qh qj qk ql

w; wa ws wd

qa qs qd qf qg
qa qs qd qf qg qh qj qk ql w; wa ws wd wf wg
SHUFFLE button CONTINUE button C.INDEX button A.SPACE button TIME button Number button >10 button FILE button ERASE button REPEAT button H (play) button X (pause) button./> (AMS) button m/M (forward/backward) button INDEX >/. button PROGRAM button PEAK SEARCH button DIGITAL FILTER button DISPLAY MODE button CLEAR button CHECK button FADER button A T B button t x (stop) button LINE OUT LEVEL button

SECTION 3 DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

LOADING PANEL

OUT IN

BOTTOM VIEW

2 tray
1 Open the tray turning the tapering screw driver to the arrow direction.

5 loading panel

3 two hexagon hole bolt (LID) 4 two screws (KTP3 8)

6 connector (CN292)

FRONT PANEL
qd connector (CN203) qs connector (CN201) 3 screw (BVTT3 6) 4 harness
qa connector (CN901) 5 spacer 6 screw (3 8)
7 bracket 5 spacer 6 screw (3 8)
7 bracket qg front panel 0 connector (CN202)

9 connector (CN461)

8 connector (CN351) qf four screws (BVTT3 8)
1 five screws (BVTT3 8) 2 bottom plate

1 five screws (BVTT3 8)

PANEL (L) , (M) , (R)
6 two claws 7 panel (L) 5 panel (MD) 4 three claws

2 two claws

1 three screws (BVTT3 8)

3 panel (R)

MECHANISM DECK (CDM32BN-12C)

1 connector (CN251)

2 connector (CN91)

9 two screws (BVTP3 6)

3 connector (CN105)

4 connector (CN104)

5 connector (CN103) 6 connector (CN953) 0 mechanism deck 7 connector (CN935) 8 connector (CN914)

SECTION 4 TEST MODE

FLUORESCENT DISPLAY TUBE FULL ON AND KEY CHECK MODE
Procedure: 1. Connect TP(AFJ) and GND on the SERVO board with a lead wire. 2. Press ! button to turn the power ON. 3. The fluorescent display tube will fully turn on. 4. Pressing any button causes the set to enter the Key Check mode. In the Key Check mode, each time a button is pressed, numeric value displayed on the tube is counted up. (However, once the button is pressed, the value is not counted up even if pressing the same button again.) Also, while a button is pressed, its button number is displayed. 5. To exit from the Test mode, press ! button to turn the power OFF.

7-segment display

SERVO board (Conductor Side)

TP (AFJ) IC204 CN101

Count-up display

Button number display

Button Name PLAY MODE Partial on

Button Number Display (Display while a button is pressed)
SIDE-A FADE C. SEC DELETE CUSTOM INDEX

REPEAT

Partial on
SIDE-B (TIME) C.FILE INDEX
TIME EDIT/TIME FADE FILE ERASE CHECK CLEAR FILTER m M
Partial on Partial on 20 Partial on Partial on
1 PROGRAM INDEX SHUFFLE PEAK EDIT REPEAT AAUTOSPACE STEP _ B (JUST) 10 N 15 5

A OPEN/CLOSE N

Full on Partial on and nearby LED on
Partial on and nearby LED on 888 23

x PUSH ENTER

AGING MODE
This set has the Aging mode for operation check of the mechanism deck. If a failure occurred The aging operation stops and a faulty status is displayed on the fluorescent display tube. If no failure occurs The aging operation continues repeatedly.
Note: To enter the Aging mode, the Aging Remote Commander (J-2501-123-A) is required. 1. Press ! button to turn the power ON.

2. 3. 4. 5.

Set a disc on the tray. Press [AGING START] button on the Aging Remote Commander. The aging starts, and the fluorescent display tube will display the following. At the completion of aging, press ! button.

Code No. 6 Load IN

Status
Display in normal operation A-0 A-1 A-2 Counter display A-4 Counter display A-6
Display in case of failure Err-0 Err-1 Err-2 Err-3 Err-4 Err-5 Err-6
Access to TOC Access to last track Play of last track (3sec) Access to first track Play of first track (3sec) Load OUT
SECTION 5 ELECTRICAL ADJUSTMENTS
Notes: 1. CD block basically constructed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise indicated. 3. Use the oscilloscope with more than 10 M impedance. 4. Clean an object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks.

RF signal waveform

VOLT/DIV: 200 mV TIME/DIV: 500 ns (with the 10 : 1 prove in use) level: 1.2

+ 0.25 0.20

S-Curve Check
Note: Operate with remote commander.

Connection:

oscilloscope SERVO board TP (FE) TP (VC)
When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity. E-F Balance (Traverse) Check (Operate with remote commander) Connection:

oscilloscope (DC range) SERVO board TP (TE) TP (VC)
Procedure: 1. Connect the oscilloscope to TP (FE) and TP (VC) on SERVO board. 2. Connect the TP (ADJ) and GND with lead wire. 3. Turned power switch( ! button) on. 4. Put disc (YEDS-18) in and press the N button. Press the qa button on remote commander. (actuate the focus search) 5. Confirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3.0 1.0 Vp-p.

S-curve waveform

symmetry

within 3.0 1.0 Vp-p

Procedure: 1. Connect the TP (ADJ) to ground with lead wire. 2. Connect the oscilloscope to TP (TE) and TP (VC) on SERVO board. 3. Turned power switch ( ! button) on. 4. Put disc (YEDS-18) in and press the N button. 5. Press the 3 button on remote commander. (Tracking servo on) 6. Confirm that the oscilloscope waveform is symmetrical on the top and bottom in relation to 0 Vdc, and check this level.

Traverse waveform

6. After check, remove the lead wire connected in step 2.
Note: Try to measure several times to make sure that the ratio of A : B or B : A is more than 10 : 7. Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check Connection:
oscilloscope (AC range) SERVO board TP (RFO) TP (VC)

level: 1.5

+ 1.5 0.5
7. After check, remove the lead wire connected in step 1. E-F Balance (Traverse) Check (No remote commander) Connection:
Procedure: 1. Connect the oscilloscope to TP (RFO) and TP (VC) on SERVO board. 2. Turned power switch ( ! button) on. 3. Put disc (YEDS-18) in and press the N button. 4. Confirm that the oscilloscope waveform is clear and check RF signal level is correct or not.
Note: Clear RF signal waveform means that the shape can be clearly distinguished at the center of the waveform.
Procedure: 1. Connect the TP (TEI: IC101 pin wj) to TP (VC) with lead wire. 2. Connect the oscilloscope to TP (TE) and TP (VC) on SERVO board. 3. Turned power switch ( ! button) on. 4. Put disc (YEDS-18) in and press the N button.
5. Confirm that the oscilloscope waveform is symmetrical on the top and bottom in relation to 0 Vdc, and check this level.
6. After check, remove the lead wire connected in step 1. Skew Adjustment
Note: Do not perform the skew adjustment when not using attached stabilizer to a set.
Procedure: 1. Remove the bottom plate, put one third of the unit out from the desk. 2. Connect the osiclloscope to TP (RFO) and TP (VC) on SERVO board. 3. Turned power switch ( ! button) on. 4. Put disc (YEDS-18) in and press the N button. 5. Adjust to be clear the waveform of the oscilloscope turning the adjsutment screw with a 3 screwdriver.

Note: Clear RF signal waveform means that the shap can be clearly distinguished at the center of the waveform.

adjustment screw

3 screwdriver
6. After the adjustment, lock the adjustment screw.
SERVO BOARD (Conductor Side)

IC101 TP (FE)

TP (VC) TP (TEI) TP (RFO) TP (TE) CN101

TP (AFJ) IC204 TP (ADJ)

CDP-XA555ES SECTION 6 DIAGRAMS
6-1. BLOCK DIAGRAM SERVO Section
DIGITAL SIGNAL PROCESSOR, FOCUS/TRACKING/SLED SERVO, EFM COMPARATOR IC101 ASYO 62
PRIORITY ENCODER ADDRESS GENERATOR 32K RAM DIGITAL OUT SUBCODE P-W PROCESSOR SUBCODE Q PROCESSOR SUBQ SQCK 77

(Page 16)

39 DETECTOR INTEGRATOR Q101 RFO E RF AMP A C B D

CLOCK GENERATOR

DATA BLIS

COMPARATOR IC106

PEAK DETECTOR

78 SCLK 83

FOCUS ERROR AMP F TRACKING ERROR AMP

ASYMMETRY CORRECTION

EFM DEMODULATOR

REGISTER

D/A DATA PROCESSOR
SERIAL/PARALLEL PROCESSOR

Q103,104

SWITCHING Q105, 106

SWITCHING Q102

46 LRCK 45 BCLK 47

COMPARATOR IC107

COMPARATOR IC108

DIGITAL PLL

SYNC PROTECTOR TIMING GENERATOR 1 CLV SERVO PROCESSOR

ERROR CORRECTOR SCOR 74

TIMING GENERATOR 2 DATA 86 XLAT 87 CLK 88
LD DRIVE LD AUTOMATIC POWER CONTROL PD LDON IB TIMS OVERSAMPLING FILTER CLV SERVO PROCESSOR SERVO INTERFACE FOK M IRR DFCT DFCT FOK MIRR DETECTOR 26

CPU INTERFACE

SERVO AUTO SEQUENCER

LASER DIODE

LD VCC
FOK 93 DFCT 92 MIRR 91 XRST 81
OPTICAL PICK-UP BLOCK (KSS-273B/J1N)
FOCUS/TRACKING COIL DRIVE SLED MOTOR DRIVE IC102 T+ (TRACKING) 4 F+ (FOCUS) 24 23

TE SE EF

FOCUS SERVO A/D CONVERTER TRACKING SERVO SLED SERVO PWM GENERATOR

S STOP

SERVO DSP

MUTE GFS

TRDR TRDR
TRACKING PWM GENERATOR FOCUS PWM GENERATOR SLED PWM GENERATOR

2-AXIS DEVICE

FFDR 8 FRDR 10 SRDR 2 SFDR 100
SIGNAL GENERATOR RESET IC204
(Page 16) (Page 16) (Page 16)

F 26 M21 (SLED) 16

LOCK MUTE 15 RESET SWITCH Q151,152 98
SPINDLE MOTOR DRIVE ICL11 L4 L1113 BSL (SPINDLE) MUTE 15 SPINDLE MOTOR DRIVE ICL14 L4 MUTE 15 S22 (LIMIT IN) S21 (LIMIT OUT) CONSTANT CURRENT QCONSTANT CURRENT Q182 H12 H CONSTANT CURRENT Q171 MUTING CONTROL SWITCH Q153,CONSTANT CURRENT Q172 Q190 D+5V H11 H

RECT D935,936 D939,940

S991 (POWER) AC IN
M271 (LOADING) LOADING MOTOR DRIVE IC205 MOTOR CONTROL DRIVE LOGIC 5 6
32 SYSTEM CONTROL IC201 X201 4MHz
FL DRIVER ICDATA 18 S| S5 3A 42 3G 39 4A 37 4G 25 5A 23 5G 20

79 S14 | | 91 S26

65 LOAD IN 64 LOAD OUT
DVd+5V SYSTEM CONTROLLER(IC201) D/A CONVERTER(IC601)

+5V REGULATOR Q930

+5V S283 (LD)
13 3A3G, | 4A4G, 33 5A5G 92 S27 | | 106 S| 1A1G, 107 2A2G 6 12

S281 (IN) S282 (OUT)

45 IN/OUT SW
CLK 45 CL WR 44 WR BLK 2 BLK LED PLAY LED PAUSE LED PD/00N
18V FL DRIVER B (IC801, 802, 803)
18V REGULATOR IC932 T903 POWER TRANSFORMER (FOR DRIVE) RECT D957,958

29 LIMIT OUT RMIN

SV+7V SERVO SECTION SV7V
+7V REGULATOR IC950 7V REGULATOR IC951

16 LED DRIVE Q871873

FL DRIVER ICDATA 18 S| S1A 37 1G 39 2A 42 2G 34 28
REMOTE CONTROL RECEIVER IC804

S884892

RV870 AMS PUSH ENTER 2
D871, 872, S886 (2/2) FILTER
S850855 CLK 45 CL WR 44 WR BLK 2 BLK
NOTES FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. % : indicates tolerance. : internal component. 5 : fusible resistor. C : panel designation. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. U : B+ Line. V : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground in CD play mode. no mark : CD PLAY Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY c : digital out

Circuit Boards Location

Note on Printed Wiring Board: X : parts extracted from the component side. Y : parts extracted from the conductor side. : Through hole. b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
POWER BOARD AC BOARD COAX OUT BOARD OPT OUT BOARD SW BOARD D/O SW BOARD
Indication of transistor.
C Q B E These are omitted.
Q B C E These are omitted.

LINE OUT BOARD VR BOARD

KEY-L BOARD DISPLAY BOARD

AUDIO BOARD KEY-R BOARD

LOADING MOTOR BOARD
SERVO BOARD FLEX RELAY BOARD

BSL BOARD

FL BOARD

LOADING SW BOARD

PRINTED WIRING BOARD SERVO Board (Component Side)
See page 17 for Circuit Boards Location.

Semiconductor Location

Ref. No. D131 D132 IC110 Q171 Q172 Q181 Q182 Location C-5 C-5 B-4 D-5 D-5 D-4 D-4
PRINTED WIRING BOARD SERVO Board (Conductor Side)
(Page 35) (Page 25) (Page 35)
Ref. No. D201 D202 D203 D204 IC101 IC102 IC103 IC104 IC105 IC106 IC107 IC108 IC109 IC111 IC201 IC202 IC203 IC204 IC205 Q101 Q102 Q103 Q104 Q105 Q106 Q151 Q152 Q153 Q154 Q190 Q201 Q202 Location D-4 C-3 C-6 A-6 B-5 C-5 C-4 D-5 D-4 B-3 A-3 A-3 B-5 A-2 D-2 D-3 C-4 B-2 B-6 A-4 A-3 A-3 A-3 A-2 A-2 D-6 D-6 D-5 D-5 C-5 C-4 C-4

(Page 28)

(Page 22)

(Page 25)

(Page 30)

(Page 30) (Page 30)

PICK UP BLOCK
SCHEMATIC DIAGRAM SERVO Board (1/2)
See page 37 for Waveforms.
See page 38 for IC Block Diagrams.
(Page 26) (Page 29) (Page 26)

(Page 23)

(Page 21)

(Page 31)

SCHEMATIC DIAGRAM SERVO Board (2/2)
See page 39 for IC Block Diagrams.

(Page 36)

Ref. No. IC801 IC802 IC803 IC804 Q801 Q802 Location A-2 A-3 A-4 B-5 A-5 A-5
6-19. SCHEMATIC DIAGRAM DISPLAY Board
See page 41 for IC Block Diagram.
6-20. PRINTED WIRING BOARDS AC/POWER (Component Side) /SW Boards

(Page 35) (Page 35)

6-21. PRINTED WIRING BOARD POWER Board (Conductor Side)
Ref. No. D910 D911 D912 D913 D914 D915 D916 D917 D918 D919 D920 D930 D931 D932 D933 D934 D935 D936 D937 D938 D939 D940 D950 D951 D952 D955 D956 D957 D958 IC910 IC911 IC930 IC931 IC932 IC950 IC951 Q930 Q931 Q932 Location C-5 A-5 B-5 A-5 B-2 B-2 A-3 A-3 A-3 A-3 A-2 D-5 B-4 B-3 D-3 D-2 C-3 D-3 C-2 D-2 C-3 C-3 E-5 E-5 E-4 E-3 D-3 E-3 D-3 C-5 A-5 C-4 B-3 D-5 E-4 E-5 C-4 C-4 C-5

(Page 34)

6-22. SCHEMATIC DIAGRAM AC/POWER/SW Boards
(Page 21) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

Waveforms SERVO Board

1 IC201 # (XTALI) 6 IC101 $ (LRCK)
AUDIO Board 1 IC600 (BCKI)

4.8 Vp-p

5.2 Vp-p
2 IC101 @ (RFDC) 200 mV/DIV, 500 ns/DIV

22.7 s

7 IC101 $ (BLCK)

474 ns

2 IC600 (LRCKI)

1.2 +0.25 Vp-p 0.20

3 IC101 @ (TE) 200 mV/DIV, 100 s/DIV 8 IC101 ^ (XTAI), IC109 5

3 IC600 ! (XIN)

Approx. 400 mVp-p

4 Vp-p

16 MHz
4 IC101 @ (FE) 200 mV/DIV, 50 ns/DIV 9 IC101 ( (MDP)

44 ns 4 IC(LVCK01)

2.8 Vp-p

Approx. 200 mVp-p

1.8 Vp-p
5 IC101# (RFAC) 200 mV/DIV, 500 ns/DIV 5 IC607 3

5.8 Vp-p

45 MHz

CXD2545Q

XRST DIRC SCLK DFSW ATSK MUTE 79 SENS 80
IC Block Diagrams SERVO Board

COUT 89

CLOK 88

DATA 86

XLAT 87

FSW 94

ADD 90

SQSO 77

SQCK 78

MIRR 91 DFCT 92 FOK 93

LOCK 98 EXCK 76 MON 95 MDS 97 MDP 96

SSTP 99

SFDR 100 75
SBSO SLED SERVO SERVO AUTO SEQUENCER SERVO MICRO PROGRAM INTERFACE CLV PROCESSOR SERVO DSP NOISE SHAPER CPU PRIORITY INTERFACE ENCODER D/A DIGITAL PROCESSOR CPU ADDRESS INTERFACE GENERATOR 32K RAM SYNC PROTECTOR TIMING GENERATOR 1 SCOR WFCK EMPH CPU INTERFACE SUBCODE Q PROCESSOR SUBCODE P-W PROCESSOR TRACKING SERVO FOCUS SERVO

SLED PWM GENERATOR

TRACKING PWM GENERATOR
18-TIMES OVER SAMPLING FILTER CPU ERROR INTERFACE CORRECTOR RESISTER
SRON SRDR SFON TFDR TRON TRDR TFON FFDR FRON FRDR FFON

FOCUS PWM GENERATOR

PWM GENERATOR

VCO0 VCO1

TEST DVSS TES2 TES3 CPU TIMING INTERFACE GENERATOR 2 3

MIRR DFCT FOK DETECTOR

DIGITAL OUT

D OUT MD2

C16M C4M FSTO CLOCK GENERATOR FSTI DVSS XTSL XTAO XTAI

5V I/O

CLOCK GENERATOR R CH D/F L CH D/F 3.3V/ 5V/ I/O
VSUB (D) VSUB (C) VDD2 VDD L1 () NC VSS L1 (+) VSS2

L CH PWM GENERATOR

CTLVDD MUTE SYNC MODE FIL2 FIL1 CTLVSS VSUB (D) VSUB (C) VDD2 VDD R1 () NC VSS R1 (+) VSS2

R CH PWM GENERATOR

L CH PWM BUFFER

MASTER CLOCK GENERATOR

R CH PWM BUFFER
VSS2 L2 (+) VSS NC L2 () VDD VDD2 VSUB (A) L NC XVDD XOUT NC XIN XVSS XVSUB NC VSUB (A) R
VDD2 VDD R2 () NC VSS R2 (+) VSS2
DISPLAY Board IC801, 802, 803

LC7570E

NC VDA

VFL S0 S1 S2

NC 1 BLK 2 VSS 3 SIN S33 S32 S31 S30 S29 S28 S27 SSHIFT REGISTER A/D CONVERTER

S3 NC S4

LATCH, FL DRIVER
S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 S15 S16
NC S25 S24 S23 S22 S21 NC S20 S19 S18 S17 NC
IC PIN FUNCTION DESCRIPTION
SERVO BOARD IC101 CXD2545Q (DIGITAL SIGNAL PROCESSOR, FOCUS/TRACKING/SLED SERVO, EFM COMPARATOR) Pin No. 43 Pin Name SRON SRDR SFON TFDR TRON TRDR TFON FFDR FRON FRDR FFON VCOO VCOI TEST DVSS TES2 TES3 PDO VPCO VCKI AVD2 IGEN AVS2 ADII ADIO RFDC TE SE FE VC FILO FILI PCO CLTV AVS1 RFAC BIAS ASYI ASYO AVD1 DVDD ASYE PSSL I/O O O O O O O O O O O O O I I I I O O I I I O I I I I I O I O I I I I O I I Description Sled servo drive PWM signal output terminal Not used (open) Sled servo drive PWM signal () output to the BA6297AFP (IC102) Sled servo drive PWM signal output terminal Not used (open) Tracking servo drive PWM signal () output to the BA6297AFP (IC102) Tracking servo drive PWM signal output terminal Not used (open) Tracking servo drive PWM signal (+) output to the BA6297AFP (IC102) Tracking servo drive PWM signal output terminal Not used (open) Focus servo drive PWM signal (+) output to the BA6297AFP (IC102) Focus servo drive PWM signal output terminal Not used (open) Focus servo drive PWM signal () output to the BA6297AFP (IC102) Focus servo drive PWM signal output terminal Not used (open) Oscillator circuit output terminal for analog PLL of the playback EFM Not used (open) Oscillator circuit input terminal for analog PLL of the playback EFM Not used (fixed at L) Input terminal for the test (fixed at L) Ground terminal (digital system) Input terminal for the test (fixed at L) Input terminal for the test (fixed at L) Charge-pump output terminal for analog PLL of the playback EFM Not used (open) PLL charge-pump output terminal for the variable pitch Not used (open) Clock signal input from external VCO for the variable pitch Not used (fixed at L) Power supply terminal (+5V) (analog system) Power supply terminal (+5V) (for operational amplifier) Ground terminal (analog system) Input terminal for the A/D converter Not used (open) Output terminal of the operational amplifier Not used (open) RF signal (DC level) input terminal for the digital servo process Tracking error signal input from the RF amplifier in optical pick-up Sled error signal input from the RF amplifier in optical pick-up Focus error signal input from the RF amplifier in optical pick-up Middle point voltage (+2.5V) input from the RF amplifier in optical pick-up Filter output terminal for master clock of the playback master PLL Filter input terminal for master clock of the playback master PLL Phase comparison output terminal for master clock of the playback EFM master PLL Internal VCO control voltage input of the playback master PLL Ground terminal (analog system) RF signal (AC level) input terminal for the EFM demodulator Constant current input terminal of the playback EFM asymmetry circuit Playback EFM asymmetry comparator voltage input terminal Playback EFM full-swing output terminal Power supply terminal (+5V) (analog system) Power supply terminal (+5V) (digital system) Playback EFM asymmetry circuit on/off selection input terminal (fixed at H) Audio data output mode selection input terminal (fixed at L)

Pin No. 99 100

Pin Name SBSO EXCK SUBQ SQCK MUTE SENS XRST DIRC SCLK DFSW ATSK DATA XLAT CLOK COUT DVDD MIRR DFCT FOK FSW MON MDP MDS LOCK SSTP SFDR
I/O O I O I I O I I I I I I I I O O O O O O O O O I O
Description Sub-code P-W serial data output terminal Not used (open) Sub-code P-W serial data reading clock signal input terminal Not used (fixed at L) Sub-code Q data signal output to the system controller (IC201) Sub-code Q data reading clock signal input from the system controller (IC201) Mute signal input from the system controller (IC201) Internal status (SENSE) signal output to the system controller (IC201) System reset signal input from the reset signal generator (IC204) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H 1-track jump mode input terminal Not used (fixed at H) Sense serial data reading clock signal input from the system controller (IC201) Defect on/off select signal input terminal Not used (fixed at L) Input terminal for the anti-shock Not used (fixed at L) Serial data input from the system controller (IC201) Serial data latch pulse signal input from the system controller (IC201) Serial data transfer clock signal input from the system controller (IC201) Track number count signal output terminal Not used (open) Power supply terminal (+5V) (digital system) Mirror detection signal output terminal Not used (open) Defect signal output terminal Not used (open) Focus OK signal output terminal Not used (open) Selection signal output terminal of the output filter for spindle motor Not used (open) Spindle motor on/off control signal output terminal Not used (open) Spindle servo control signal output terminal Spindle servo control signal output terminal Not used (open) GFS is sampled by 460 Hz H output when GFS is H Not used (open) Detection input from the sled limit-in detect switch (S22) The optical pick-up is inner position when H Sled servo drive PWM signal (+) output to the BA6297AFP (IC102)
SERVO BOARD IC201 CXP84124-085Q (SYSTEM CONTROLLER) Pin No. Pin Name A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 WE NC NC LED-PLAY LED-PAUSE LED-FILTER SPDL-MUTE SHIFT-ON/OFF VOL UP VOL DOWN BLANK FL D0 FL D1 FL D2 FL CLK FL WR SENSER SW SENSER LIMIT OUT RESET XTALI XTALO VSS TX TEX AVSS AVREF K0 K1 K2 I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O I I I I O O I I I I I Description Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Address signal output to the static RAM (IC202) Write enable signal output to the static RAM (IC202) Not used (fixed at H) Not used (fixed at H) N LED (D871) drive signal output terminal H: LED on X LED (D872) drive signal output terminal H: LED on FILTER LED (S886(2/2)) drive signal output terminal H: LED on Mute signal output to the spindle motor driver (IC104, 105) Reset signal output terminal Not used (open) Volume up control signal output to the volume control motor driver (IC350) Volume down control signal output to the volume control motor driver (IC350) Blank signal output to the fluorescent indicator tube driver (IC801 to IC803) Serial data output to the fluorescent indicator tube driver (IC803) Serial data output to the fluorescent indicator tube driver (IC802) Serial data output to the fluorescent indicator tube driver (IC801) Serial data transfer clock signal output to the fluorescent indicator tube driver (IC801 to IC803) Read/write select signal output to the fluorescent indicator tube driver (IC801 to IC803) On/off control signal output to the stabilizer detect sensor (IC203) H: on Detect signal input from the stabilizer detect sensor (IC203) H: on Detection input from the sled limit-out detect switch (S21) The optical pick-up is outer position when L System reset signal input from the reset signal generator (IC204) L: reset For several hundreds msec. after the power supply rises, L is input, then it changes to H Main system clock input terminal (4 MHz) Main system clock output terminal (4 MHz) Ground terminal Sub system clock output terminal Not used (open) Sub system clock input terminal Not used (fixed at L) Ground terminal (for A/D converter) Reference voltage input terminal (+5V) Key input terminal (A/D input) ERASE key (S850) input Key input terminal (A/D input) FILE, EDIT/TIME FADE, TIME, REPEAT, P MODE keys (S851 to S855) input Key input terminal (A/D input) CHECK, CLEAR, FILTER, m, M , PUSH ENTER keys (S884 to S888, RV870) input

20% 20%

* * * *
20% 20% 5% 5% 20% 5% 5% 5% 5% 20% 5% 5% 10% 10% 10% 20% 20% 20% 20% 10% 20%
* CN607 * CN608 CN609 * CN610 * CN612 CN613 * CN614
1-691-459-21 PIN, CONNECTOR (PC BOARD) 3P 1-564-507-11 PLUG, CONNECTOR 4P < DIODE >

D601 D602 D603 D604

8-719-114-30 8-719-114-30 8-719-402-47 8-719-801-78
DIODE DIODE DIODE DIODE < IC >
RD5.1JS-T2AB2 RD5.1JS-T2AB2 MA3130M-TX 1SS184-TE85L
IC401 IC402 IC403 IC501 IC502 IC503 IC600 IC601 IC602 IC603 IC604 IC605 IC606 IC607
8-759-371-51 8-759-566-39 8-759-566-39 8-759-371-51 8-759-566-39 8-759-566-39 8-759-573-17 8-759-596-81 8-759-296-74 8-759-296-74 8-759-566-39 8-759-566-39 8-759-711-85 8-759-242-70
IC IC IC IC IC IC IC IC IC IC IC IC IC IC
CXA8042AS OPA2132UA/2K5 OPA2132UA/2K5 CXA8042AS OPA2132UA/2K5 OPA2132UA/2K5 CXD8762Q CXD9521Q AD712JR-REEL AD712JR-REEL OPA2132UA/2K5 OPA2132UA/2K5 NJM4580E-D (T1) TC7WU04F-TE12L
20% 5% 5% 20% 10% 20% 20% 20% 20% 20% 5% 5% 5% 5% 5% 5% 20% 20% 20%
< SHORT > JW610 JW611 1-216-295-00 SHORT 1-216-295-00 SHORT < COIL > L451 L452 L453 L454 L455 L551 L552 L553 L554 L555 L600 1-410-757-21 1-414-520-21 1-414-512-21 1-414-512-21 1-414-512-21 1-410-757-21 1-414-520-21 1-414-512-21 1-414-512-21 1-414-512-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 0.33mH 10uH 6.8uH 6.8uH 6.8uH 0.33mH 10uH 6.8uH 6.8uH 6.8uH 0.33mH 0 0

1-410-757-21 INDUCTOR

Ref. No. L601 L604 L605 L607 L609 L611 L614 L616 L619 L620 L621 L622 L625 L626 L627 L628 L629 L630 L631 L632 Part No. 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-424-090-11 1-414-520-21 1-424-090-11 1-410-757-21 1-424-090-11 1-424-090-11 Description COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER COIL, LINE FILTER INDUCTOR 10uH COIL, LINE FILTER INDUCTOR 0.33mH COIL, LINE FILTER COIL, LINE FILTER Remark Ref. No. R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R428 R429 R451 R452 R453 R454 R455 R456 R481 R482 R483 R484 R491 R501 R502 R503 R504 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R518 R519 R520 R521 R522 R523 R524 R525 R526 R528 R529 R551 R552 R553 R554 R555 R556 R581 R582 Part No. Description 100 3.3K 3.3K 3.3K 3.3K 1K 1K 1K 10 1K 4.7K 100K 15K 33K 47K 330 3.3K 2.4K 3.3K 1K 3.3K 3.3K 3.3K 3.3K 1K 1K 1K 10 1K 4.7K 100K 15K 33K 47K 330 1% 2% 2% 2% 2% 2% 2% 2% 2% 2% 1% 2% 2% 2% 2% 2% 2% 2% 5% 5% 5% 5% 2% 5% 5% 5% 5% 2% 2% 1% 2% 2% 1% 1% 2% 2% 1% 1% 2% 2% 2% 2% 2% 2% 2% 2% 2% 1% 2% 2% 2% 2% 2% 2% 2% 5% 5% Remark 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/2W 1/8W 1/8W 1/2W 1/2W 1/8W 1/8W 1/2W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/10W 1/10W 1-259-545-11 CARBON 1-259-978-11 1-259-983-11 1-260-002-11 1-260-002-11 1-260-002-11 1-260-002-11 1-259-995-11 1-259-995-11 1-259-995-11 1-259-507-11 1-259-995-11 1-260-004-11 1-260-020-11 1-260-010-11 1-260-014-11 1-260-016-11 1-259-979-11 1-216-037-00 1-216-037-00 1-216-037-00 1-216-037-00 1-260-002-11 1-216-029-00 1-216-029-00 1-216-029-00 1-216-029-00 1-259-927-11 1-260-002-11 1-259-549-11 1-259-983-11 1-259-995-11 1-259-507-11 1-259-545-11 1-259-978-11 1-259-983-11 1-259-507-11 1-259-545-11 1-259-978-11 1-259-983-11 1-260-002-11 1-260-002-11 1-260-002-11 1-260-002-11 1-259-995-11 1-259-995-11 1-259-995-11 1-259-507-11 1-259-995-11 1-260-004-11 1-260-020-11 1-260-010-11 1-260-014-11 1-260-016-11 1-259-979-11 1-216-037-00 CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF METAL CHIP METAL CHIP METAL CHIP METAL CHIP CARBON MELF METAL CHIP METAL CHIP METAL CHIP METAL CHIP CARBON MELF CARBON MELF CARBON CARBON MELF CARBON MELF CARBON CARBON CARBON MELF CARBON MELF CARBON CARBON CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF CARBON MELF METAL CHIP

8-719-210-21 DIODE < IC >
IC101 IC102 IC103 IC104 IC105 IC106 IC107 IC108 IC109 IC110 IC111 IC201 IC202 IC203 IC204 IC205
8-752-369-78 8-759-071-79 8-759-100-96 8-759-071-79 8-759-071-79 8-759-980-44 8-759-711-85 8-759-100-96 8-759-242-70 8-759-100-96 8-759-100-96 8-752-909-65 8-759-336-84 8-749-010-61 8-759-636-16 8-759-822-09
IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
CXD2545Q BA6297AFP-T1 NJM4558M-T1 BA6297AFP-T1 BA6297AFP-T1 TL712CPS-E05 NJM4580E-D (T1) NJM4558M-T1 TC7WU04F-TE12L NJM4558M-T1 NJM4558M-T1 CXP84124-085Q LC3564SM-10-TRM IS471F M51957AL LB1641
< SHORT > JW104 JW105 1-216-295-00 SHORT 1-216-295-00 SHORT < COIL > L101 L102 L103 L104 1-424-122-11 1-424-122-11 1-414-510-21 1-414-510-21 FILTER, NOISE FILTER, NOISE INDUCTOR INDUCTOR < TRANSISTOR > Q101 Q102 Q103 Q104 Q105 Q106 Q151 Q152 Q153 Q154 Q171 Q172 Q181 Q182 Q190 8-729-232-69 1-801-806-11 8-729-900-53 8-729-900-53 8-729-027-23 8-729-900-53 8-729-027-38 1-801-806-11 8-729-027-38 1-801-806-11 8-729-232-69 8-729-232-69 8-729-232-69 8-729-232-69 8-729-027-38 FET 2SK208-GRT5LSONY-1 TRANSISTOR DTC144EKA-T146 TRANSISTOR DTC114EKA-T146 TRANSISTOR DTC114EKA-T146 TRANSISTOR DTA114EKA-T146 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114EKA-T146 DTA144EKA-T146 DTC144EKA-T146 DTA144EKA-T146 DTC144EKA-T0
0.5% 0.5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
FET 2SK208-GRT5LSONY-1 FET 2SK208-GRT5LSONY-1 FET 2SK208-GRT5LSONY-1 FET 2SK208-GRT5LSONY-1 TRANSISTOR DTA144EKA-T146
Ref. No. R155 R156 R157 R161 R162 R163 R164 R165 R166 R167 R168 R171 R172 R173 R174 R175 R176 R177 R178 R179 R181 R182 R183 R184 R185 R186 R187 R188 R189 R190 R191 R192 R193 R194 R195 R196 R197 R198 R199 R201 R202 R203 R204 R205 R206 R207 R208 R209 R211 R212 R213 R214 R215 R216 R217 R218 R219 Part No.
Description 100K 33K 33K 12K 56K 68K 68K 68K 100K 4.7K 100K 2.2K 2.2K 470K 470K 220K 220K 1M 1M 10 2.2K 2.2K 470K 470K 220K 220K 1M 1M 10 10K 6.8K 1K 10 470K 470K 33K 220 1K 1K 6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 6.8K 10K 100K 33 10K 10K 68 39K 15K 3.3K 680 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. R220 R221 R222 R223 R224 R230 R231 R232 R233 Part No. 1-216-073-00 1-216-073-00 1-216-097-00 1-216-073-00 1-216-073-00 1-216-295-00 1-216-061-00 1-216-061-00 1-216-085-00 Description METAL CHIP METAL CHIP RES, CHIP METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP METAL CHIP < VIBRATOR > X201 1-577-082-11 VIBRATOR, CERAMIC (4MHz) ************************************************************** 1-674-836-11 SW BOARD ********* < CONNECTOR > 10K 10K 100K 10K 10K 0 3.3K 3.3K 33K 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W

S22 1-571-958-11 SWITCH, PUSH (1 KEY) (LIMIT IN) 0 T901 1-435-067-11 TRANSFORMER, POWER 0 T902 1-435-068-11 TRANSFORMER, POWER 0 T903 1-435-069-11 TRANSFORMER, POWER ************************************************************ ************** HARDWARE LIST ************** #1 #1 #2 #3 #4 #6 #7 #8 #9 #10 #11 #12 #13 #14 #15 #16 #17 #18 #19 7-685-246-14 7-685-246-19 7-685-886-09 7-682-548-09 7-621-775-10 7-685-646-79 7-685-871-01 7-685-872-09 7-682-903-01 7-682-902-11 7-621-775-60 7-628-253-00 7-621-772-30 7-685-534-19 7-685-647-79 7-685-902-21 7-627-852-07 7-627-852-58 7-685-645-79 SCREW +KTP 3X8 TYPE2 NON-SLIT (GOLD) SCREW +KTP 3X8 TYPE2 NON-SLIT (BLACK) SCREW +BVTT 4X20 (S) SCREW (3X8) SCREW +B 2.6X4 SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTT 3X6 (S) SCREW +BVTT 3X8 (S) SCREW +PWH 3X5 SCREW +PWH 2.6X5 SCREW +B 2.6X12 SCREW +PS 2X4 SCREW +B 2X6 SCREW +BTP 2.6X8 TYPE2 N-S SCREW +BVTP 3X10 TYPE2 N-S SCREW +PTPWH 2.6X8 (TYPE2) SCREW, PRECISION +P 1.7X2.5 SCREW, PRECISION +P 1.7X5 TYPE3 SCREW +BVTP 3X6 TYPE2 N-S
************************************************************ ACCESSORIES & PACKING MATERIALS ******************************** 1-418-691-11 REMOTE COMMANDER (RM-D951) 1-791-732-11 CORD, CONNECTION 3-867-064-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH) 3-867-064-21 MANUAL, INSTRUCTION (GERMAN, DUTCH, SWEDISH, ITALIAN, PORTUGUESE) (AEP) 3-867-064-31 MANUAL, INSTRUCTION (CHINESE) (Singapore) 4-981-643-01 COVER, BATTERY (for RM-D951)

9-928-966-11

Sony Corporation

Home Audio Company

99H0546-1 Printed in Japan 1999. 8 Published by Quality Assurance Dept.

BESTENLISTE

To p 0

Die AUDIO

Bestenliste

LAUTSPRECHER

Die AK = AUDIO-Kennzahl gibt Auskunft ber die Kombinationsfhigkeit des Lautsprechers mit Vollverstrkern und Endstufen (a = aktiv). Die BoxenKennzahl sollte mglichst nicht ber der entsprechenden AK des zu kombinierenden Verstrkers liegen; dann ist auch bei hheren Lautstrken die unverflschte Reproduktion der Dynamikspitzen mglich. Zustzlich geben Abkrzungen Auskunft ber die Gre der Boxen: (S) steht fr Standbox, (K) fr Kompaktbox und (SSS) fr Subwoofer/Satelliten-System. Die Buchstaben A bis F kennzeichnen die Verarbeitungsqualitt von berragend (A) bis mangelhaft (F).
Modell Preis/Paar AK Test Punkte Prdikat HGP Fuga 2 (S) JM Lab Electra 936 (S) Lua 1.3 Con Brio Diva (S) Martin Logan Re-Quest (S) Aerial Model 8 (S) Avalon Symbol (S) B&W Nautilus 804 (S) HGP Fuga Supertech (S) Lindemann Venice (S) Lua 1.3 Con Brio (S) Magnepan MG 3.6 SE (S) Quadral Aurum Vulkan (S) 7/01 11/01 10/99 7/98 1/98 5/01 12/99 2/97 4/98 2/99 12/00 5/91

SPITZENKLASSE
Cabasse Iroise 500 (S) 12/Dynaudio Contour 3.3 (S) 2/Heco Anniversary (S) 1/HGP Corda (S) 6/JBL Ti 6 K (S) 11/Linn Trikan aktiv + Sizmik (K) 10000 a 11/Audiodata Elance (S) 2/Linear Acoustic LA 20 Jet (S) 2/Manger Zerobox 103 (S) 11/Audio Physic Libra (S) 4/Isophon Enigma (S) 8/T+A TAL 160 (S) 11/ALR Factor 2 (S) 5/Dali Grand (S) 2/Dynaudio Contour 3.0 (S) 10/Fischer & Fischer SN 400 (S) 9/JM Lab Micro Utopia (K) 11/Mirage OM 5 (S) 11/Moll Audio Antares (K) 7900 a 12/Wilson Benesch ACT One (S) 2/Canton Ergo RCA (S) 9/Dynaudio Special Twenty-Five (K) 10/Visonik Concept 7 (S) 5/ALR Take 6 (S) 3/B&W CDM 9 NT (S) 12/B&W Signature 805 (K) 1/03 84/A Elac 518 (S) 11/ProAc Studio 125 (S) 7/Quadral Aurum Montan (S) 11/Elac Dolce Vita (S) 7/Sony SSX 90 ED (S) 1/03 83/C Triangle Ventis XS (S) 5/Audio Physic Tempo 3i (S) 5/Dynaudio Contour 1.3 SE (K) 5/Infinity Kappa 600 (S) 8/JM Lab Cobalt 826 S (S) 2/Mission 783 (S) 11/Monitor Audio Gold Reference 20 (S) 7/B&W Nautilus 805 (K) 3/Canton Ergo 1200 (S) 2/Elac Authentic 330 (K) 3/Magnepan Magneplanar 1.6 (S) 7/MBL 311 E (K) 12/ProAc 2.5 (S) 2/Canton Karat M 80 (S) 10/Elac 512 (S) 11/Isophon Galileo (K) 2/JM Lab Electra 906 (K) 3/Tannoy D-900 (S) 2/Thiel MCS 1 (K) 1/Visonik Concept 5 (S) 11/A.D.A.M. A.R.T. Compact (K) 10/ASW Cantius VI (S) 12/Audio Physic Tempo (S) 5/Elac 516 (S) 8/Infinity Kappa 400 (S) 2/Isophon Spirit (S) 2/JM Lab Cobalt 816 Signature (S) 8/Quadral Aurum 9 (S) 5/

REFERENZKLASSE

Martin Logan Statement (S) Dynaudio Evidence (S) 3 Wilson Audio X-1 Grand Slamm III (S) Audio Physic Cerubin (S) B&W Nautilus + Accuphase DF-35 (S) Krell LAT-1 (S) Wilson Audio Maxx (S) Avalon Eidolon Diamond (S) Backes & Mller BM 30 (S) Linn Komri (S) 1 Avalon Opus (S) Genesis 200i (S) B&W Nautilus 800 (S) TAG McLaren F1 AvantGarde (S) Wilson Audio Watt/Puppy 6 (S) B&W Nautilus (S) Revel Ultima Salon (S) Wilson Audio Sophia (S) B&W Nautilus 801 (S) Cabasse Adriatis (S) Dynaudio Confidence C4 (S) Martin Logan Prodigy (S) Revel Ultima Studio (S) T+A TCI 1 RE (S) Ascendo System Z (S) Backes & Mller BM 18 (S) Infinity Intermezzo (S) Avalon Arios (S) Isophon Europa 2 (S) MBL 101D (S) Revel Performa F 50 (S) Audio Physic Avanti 3 (S) B&W Nautilus 802 (S) Backes & Mller BM 12 (S) Canton Karat R 2 DC (S) Isophon Europa (S) JM Lab Electra 946 (S) Martin Logan Odyssey (S) MBL 111 B (S) A.D.A.M. A.R.T. Column (S) ALR Factor 7 (S) Audio Physic Caldera (S) Cabasse KI + Thor (SSS) Isophon Vieta (S) KEF Reference 203 (S) Quadral Aurum Titan (S) Revel Performa F-30 (S) Ascendo System E (S) B&W Nautilus 803 (S) JBL Ti 10 K (S) Moll Audio Atair (S) Piega LDR P 8 Limited (S) Tannoy Dimension TD 10 (S) T+A TCI 3R (S) Aerial 10 T (S) Burmester 961 MK2 (S) Elac Spirit Of Music (S) 8200 aaa aa 57 a 48 7/4/6/6/1/7/12/1/03 101/A 6/11/12/5/11/9/11/12/8/6/9/6/4/11/2/11/7/6/8/6/1/03 96/B 7/2/1/12/4/6/6/7/10/5/2/3/2/3/7/1/03 94/C 3/10/01/11/10/01/9/6/9/11/12/6/

Mark Levinson No. 40 ab 48000 1/03 117/A (100/110/140) Proceed AVP 2 ab 9800 8/02 112(105/100/130) Lexicon MC-12 ab 13200 12/(105/100/125) Bryston SP 1.7 700012/(105/95/120) 1 Lexicon MC-3/(105/95/120) Meridian 2/(105/90/120) Krell HTS 10000 8/(105/85/115) Integra Research RDC-3/(95/90/115) TAG McLaren AV-32 R 4000 6/(100/85/115) TAG McLaren AV 30 R (7.1) 350012/(90/90/110)

NAD S 170

480012/(95/85/105)

Marantz AV-9000

Denon DL 304 (MC) Goldring Eroica LX (MC) Ortofon Nr. 2 (MC)

330 6/280 6/180 6/

Marantz DR 60501

750 1/(A75/D80)

Harman/Kardon CDR 21 LG ADR-6201 Pioneer PDR-609 Philips CDR Philips CDR-602 Pioneer PDR-W Pioneer PDR-W Teac RW-800 JVC XL-RPanasonic SL-PR Thomson DAR 20601 Yamaha CDR-D 6511 Pioneer PDR-W Teac RW-H 500 Hitachi DV-W 1 3

2000 7/(90/80/100)

Clearaudio Beta-S (MM) Goldring 1025 (MM) Ortofon Vinyl Master Blue (MM) Ortofon Vinyl Mater Red (MM) Sumiko Blue Point (MCHO) Ortofon OM 30 Super (MM) Benz MC 20 E2 (MCHO) Denon DL 103 (MC) Denon DL 160 (MCHO) Dynavector DV 50 X Mk.2 (MCHO) Denon DL 110 (MCHO) Grado Prestige Gold (MM) Ortofon MC 3 Turbo (MCHO) Rega Elys (MM) Ortofon Vinyl Master White (MM) Audio Technica AT 110 E (MM) Audio Technica AT 440 ML (MM) Linn K 9 (MM) Sumiko Pearl (MM) Ortofon OM 10 Super (MM) 6/99 6/99 11/02 11/02 6/99 6/99 6/99 6/99 6/99 6/99 6/99 6/99 6/99 6/99 11/02 6/99 6/99 6/99 6/99 6/38
nachbewertet in AUDIO 5/00
P L AT T E N S P I E L E R
Die AUDIO-Bewertung gilt jeweils fr die aufgefhrte Laufwerk/ Tonarmkombination. Mit anderen Tonarmen kann das Ergebnis abweichen. Die Buchstaben A bis F kennzeichnen die Verarbeitungsqualitt von berragend (A) bis mangelhaft (F).
Transrotor Gravit Transrotor Tourbillon Clearaudio Maximum Solution /TQ-I/Sigma VPI TNT Mk 4 mit Audioquest AQ 7000 Fe5 SME Model 30 mit Ortofon Vero Clearaudio Reference mit Clearaudio Insider Transrotor Pianta SL 80, SME V, Goldring Elite Transrotor Super Seven, SME 3050, Clearaudio Insider Wilson Benesch mit Ortofon Vero 1/3/12/1/7/1/98 95