3-862-158-13(1)

CDU948S

CD-R Drive Unit

Users Guide
1997 by Sony Corporation Printed in Japan

Owners Record

The model and serial numbers are located on the bottom of the drive. Record these numbers in the spaces provided below. Refer to them whenever you call upon your sales representative regarding this product. Model No. Serial No.
Safety Regulations WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

CAUTION

As the laser beam in this CDU948S is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. The use of optical instruments with this product will increase eye hazard. The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation.

DANGER VORSICHT

INVISIBLE LASER RADIATION WHEN OPEN. AVIOD DIRECT EXPOSIRE TO BEAM UNSICHTBARE LASERSTRAHLUNG. WENN ABDECKUNG GEOFFNET NICHT DEMSTRAHL AUSSETZEN.
This label is located on the drive units internal chassis. Dieses Etikett befindet sich auf dem inneren Chassis des Laufwerkes.
INVISIBLE LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM. RADIATIONS INVISIBLES DU LASER EN CAS D'OUVERTURE. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU. VORSICHT UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEFFNET. NICHT DEM STRAHL AUSSET ZEN. ADVARSEL USYNLIG LASERSTRLING VED BNING. UNDG UDS/ETTELSE FOR STRLING.

DANGER DANGER

ADVARSEL USYNLIG LASERSTRLING NR DEKSEL PNES.
UNNG EKSPONERING FOR STRLEN.

VARNING VAROI

OSYNLIG LASERSTRLING NR DENNA DEL AR PPNAD. STRLEN R FARLIG. NKYMTN AVATTAESSA OLET ALTTINA LASERSTEILYLLE. L KATSO STEESEN.
This label is located on the bottom of the drive unit enclosure. Dieses Etikett befindet sich am Boden des Laufwerksgehuses.
This unit uses CD-R discs with the following mark.
This unit uses CD-ROM discs with the following mark.
When you use this unit as a CD player, use compact discs with the following mark.
WARNING For the customers in U.S.A.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no gurantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
CLASS 1 LASER PRODUCT LASER KLASSE 1 PRODUKT
This CD-R drive unit is classified as a CLASS 1 LASER PRODUCT. The CLASS 1 LASER PRODUCT label is located at the bottom of the enclosure.
Bei diesem CD-R-Laufwerk Serie handelt es sich um ein Laser-Produkt der Klasse 1. Dieses Etikett befindet sich am Boden des Laufwerksgehuses.

Contents

Introduction 5
Location and Function of Parts and Controls
Front Panel.... 6 Rear Panel... 7

Precautions

Example of System Setup
Installing the Drive Unit into the Computer
Getting Started... 10 Setting the Jumpers... 10 Opening the Computer... 12 Connecting the Drive.. 13 Mounting the Drive... 14 Host Adapter Installation... 16 Closing the Computer... 17

Installing the Software Driver

Using Discs and Caddies

Loading a Caddy with a Disc.. 19 Storing Discs and Caddies... 21 Care of Discs... 21

Operating the Drive

Starting Up... 22 Ejecting a Caddy... 23

Specifications

Introduction
The CDU948S is a drive unit for CD-R discs, which stores a maximum of 650 Mbytes of digital data. The drive unit has the following features: Reads and writes data in each CD-ROM, CD-ROM XA and Multi-Session standard formats. Reads standard CD-DA (Red Book) encoded discs, and reads and writes CD-R discs conforming to Orange Book Part II. Supports the following write modes: Disc at once, Session at once, Track at once, Variable packet, Fixed packet and Multisession. Outputs the audio as 16-bit digital data over the SCSI interface. Supports read and write operation at each standard speed, double speed and quadruple speed, and read-only operation at eightfold speed. Supports real time error correction at all speeds. 5 1/4 inch half-height drive form factor. SCSI bus interface embedded. (Based on SCSI-2) 2 MB buffer memory. Capable of audio CD playback provided with audio line output and headphones jack. Fast access time assures high-speed reading and writing operations. CD caddy for disc protection. Power loading and power eject. Emergency eject function which allows the caddy to be ejected manually. Capable of real time layered error correction. Employs a casing with an airtight frame. s Software requirement Install the appropriate application software before using this unit.

Front Panel

CD Caddy
1 Caddy insertion slot Accepts a caddy loaded with a CD-ROM or CD-R disc. 2 Emergency eject hole Insert a fine rod into this hole to eject a caddy manually in emergencies. 3 Eject button Ejects the caddy from the drive unit. 4 Busy indicator This indicator shows the units status in various phases of operation. * Seek, read and write: Flashes amber * Error: Lights up amber and stays lit When the power is turned on, the indicator lights up green. 5 Volume control Controls the volume of the analog audio output provided via a headphones jack. 6 Headphones jack Provides two channel analog audio output.

Rear Panel

1 Jumper block for SCSI bus Specify assignment of the SCSI bus. 2 Terminators The terminator resistors are inserted into the sockets. Remove the resistors when the SCSI bus is to be terminated externally. Note: Some models are shipped without terminators. When installing the terminators, orient them so that the GND pin (the end marked with a dot) is toward the right side of the socket. 3 Power-in connector Connect to the power supply of the host computer. 4 SCSI bus interface connector Connect to a SCSI host adapter using a connecting cable. 5 Audio output connector Outputs analog audio signals. See page 14 for detail. 6 Frame ground tab Connect to one of the host computers ground cables when the drive frame is not in direct contact with the computer.

s Installation Avoid placing the drive in a location subject to: high humidity high temperature excessive dust mechanical vibration direct sunlight. We recommend to use the drive in a horizontal position. Do not use it in a tilted position. s Operation Do not move the drive during operation. This may cause it to malfunction during reading or writing. Avoid exposing the drive to sudden changes in temperature as condensation may form on the lens inside the drive as a result. Should the surrounding temperature suddenly rise while the drive is on, wait at least one hour before you turn off the power. Operating the drive immediately after a sudden increase in temperature, may result in a malfunction during reading or writing. s Transportation Keep the original packing materials for future transport of the drive. Remove the caddy before moving the drive and, if you take the drive out of the computer, repack the drive as you received it.
To use the CD-R device, the following components are required: Computer (IBM-PC/AT* compatible) SCSI-Host adapter SCSI-Interface cable (50 to 50 pin flat cable) Software (Device driver, utilities)
* IBM-PC/AT is a registered trademark of International Business Machines Corporation.
As you go through this section, you may wish to refer to your computers manual for a more detailed description of how to install internal drives.

Getting Started

Prepare the necessary parts and tools that have not been supplied: Screwdriver four screws 3 mm in diameter (Screws must not extend more than 4.0 mm into the side panels or the bottom plate.) two mounting rails if your computer has mounting tracks. Unplug the computer and disconnect the cables attached to the back for your own safety. Do not turn on the power of the computer before completing the entire installation process.

Setting the Jumpers

Set the jumpers on the rear panel of the drive unit in accordance with the configuration of your computer system. The jumpers are preset, as illustrated below, at the factory.
Remove the jumper to set to OFF, and install the jumper to set to ON. The recommended jumper is AMP* Shunts (14227-1), JAE** Short Socket (PS-2SH4-1) or equivalent. The following table shows the function of each jumper. Jumper DEVICE TYPE Function The setting of this jumper determines whether the SCSI device type code in the inquiry data is WO or CD-ROM. ON: WORM OFF: CD-ROM Assign the drive units ID number by setting these jumpers to ON or OFF. Do not assign the same number as one used for other SCSI device. ID number KEY PREVENT/ ALLOW Jumper settings 2 OFF OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON ON OFF ON OFF ON ON ON ON ON

ID SELECT

TEST MODE
Used to prevent the SCSI bus interface connector from being plugged in upside down. ON: Allows insert and removal of a CD caddy with the eject button and the eject command. OFF: Prevents insert and removal of a CD caddy with the eject button or an eject command. ON: Enables test mode. OFF: Enables normal operation. Factory settings

No te s : The upper row of pins (without KEY position) is ground. ID SELECT, PREVENT/ALLOW, and TEST MODE are recognized when the power supply is turned on or SCSI bus is reset. TEST MODE is used exclusively for the factory testing. Do not set TEST MODE to ON. Doing so may cause an unexpected result.
* AMP is a registered trademark of AMP, Inc. ** JAE is a registered trademark of Japan Aviation Electronics Industry, Ltd. Installing the Drive Unit into the Computer

Opening the Computer

1 If your computer has its rear side covered by a plastic panel
attached with plastic hook pad, pull it off.
2 Remove the cover mounting screws. 3 Remove the cover of the computer.

Connecting the Drive

Attach one end of the flat cable (SCSI cable) to the connector on the rear of the CD-R drive.
Note: The red edge of the flat cable should be positioned next to the power supply connector. It is important that this cable be connected firmly and correctly.
s Audio output connector The audio output connector recommended is Molex 5159PBT contacts and 5051-04 housing or 5103 PBT contacts and 5102-04 housing.

Pin assignment

Mounting the Drive
1 Route the flat cable through the drive bay from the front of the
computer and insert the CD-R drive into the bay as shown. Secure the CD-R drive to the frame by using the prepared screws.

CE FA ER INT

R TO EC NN CO
12V GND UT -5% INP 5V+ DC
DLT R GN OU IO AUD ND F.G
DELLOW T MOT/A TES VEN PRE ECT SEL ID ITY PAR
Note: If you cannot secure the CD-R drive to the drive bay, you may need to install slide rails (not included) to the CD-R drive. Refer to your computer users guide for additional information.
2 Locate an available power supply cable inside your computer and
connect it to the power supply connector on the rear of the CD-R drive as shown.
Caution: Improper connection may damage the drive and void the warranty. s Frame ground When normally installed, the drive unit is not in contact with the host computer directly and should be grounded. Connect the frame ground tab to one of the host computers ground cables.

The frame ground cable recommended has a AMP 1-480435-0 housing and 170203-2 or 60711-1 contacts.
Host Adapter Installation
Connect the free end of the flat cable to the existing SCSI host adapter card and install the host adapter in the computer by inserting it securely in a system expansion slot. Refer to the operating instructions of the host adapter for complete instructions on its installation and the assignment of its switches.
No t e s : The red edge of the flat cable must be closest to pin number 1 of the interface card connector. The following illustration is a sample system configuration of the Sony CDU948S CD-R drive installation with a SCSI card.

Termination

If the CD-R drive is connected at the end of the SCSI chain, keep the drive terminator mounted at the drive. If the CD-R drive isnt the last device at the SCSI bus, remove the termination from the CD-R drive and make sure that the last device at the SCSI bus has a proper termination installed. Be aware that the SCSI bus needs to be terminated at each end of the SCSI bus cable.

Closing the Computer

1 Replace the cover on the computer, being careful to reinstall all
screws that were removed.
2 Replace the AC power cord and turn on your computer.
MSCDEX and the device driver for an ordinary SCSI CD-ROM drive can be used when using the CDU948S as a SCSI CD-ROM drive. Use the device driver for a CD-R drive when using the CDU948S as a recordable drive. Be sure to install the device driver before operating the drive. Refer to the manual supplied with the host adapter for instructions.
Loading a Caddy with a Disc
1 To open the caddy lid, press the tabs on the both sides of the
caddy at the end opposite to the shutter.
2 Set a disc, with its label upward, in the caddy.
Be careful not to touch the recording surface when setting a CDR disc in the caddy. Data cannot be recorded if the recording surface is contaminated.

3 Close the lid firmly.

Important: Do not drop the disc or the caddy. The caddy is designed so that its shutter automatically opens when it is inserted into the drive unit. Do not open the shutter manually and touch the disc. Data cannot be recorded if the recording surface is contaminated.

The caddy is precisely adjusted at the factory. Do not disassemble it.
Storing Discs and Caddies
Remove the caddy from the drive unit before moving the drive. Do not store the disc and caddy in a location subject to: high humidity high temperature excessive dust direct sunlight

Care of Discs

Hold the disc by its edge. Do not touch the surface. Wipe the CD-ROM disc with the optional CD cleaner to clean it. Do not wipe a CD-R disc with a cleaner before recording data. To avoid scratching the recording surface, blow away dust using an air blower.
Make sure that the application software is installed in the host computer before using the drive.

Starting Up

1 Turn on the power supply. 2 Insert the caddy into the drive slot with the discs label facing up,
and push it partially into the drive until the automatic loading mechanism pulls the caddy in. Important: When inserting the caddy, let the automatic loading mechanism pull it into the drive by itself. Do not hold onto the caddy or attempt to overpower the loading mechanism.
The drive begins reading the Table of Contents (TOC) data. The busy indicator lights amber while the TOC data is being read. When the busy indicator changes to green, the drive is ready to receive commands, and data may be retrieved from the disc. After loading the CD-R disc, it takes a moment for the drive to become ready while the Program Memory Area is read. From here on, follow the instructions provided with the application software. No t e s : The drive unit does not allow a caddy to be inserted if: PREVENT/ALLOW of the jumper block is set to OFF. the host computer is set to the PREVENT mode by the software. The busy indicator keeps on lighting amber if: the disc is not properly inserted. a malfunction occurs.
In such a case, eject the caddy and re-insert it properly. If the busy indicator remains lit amber, consult your dealer or qualified service personnel. The busy indicator also lights amber during audio play. However, this is not a malfunction.

Ejecting a Caddy

1 Turn on the power supply. 2 Press the eject button on the drive unit.
No te s : The eject button does not work if it is disabled by the software. To eject a caddy when the eject button is disabled by the software: Make sure that the jumper blocks PREVENT/ALLOW is set to ON. Turn the power of your computer off, and turn it on again. (Or reset the SCSI bus using a software command.)
s Ejecting a caddy manually in an emergency In the event of electrical or mechanical failure of the drive unit, a manual emergency eject is provided to allow removal of the caddy from the drive unit.

1 Turn off the power of your computer. 2 Insert a pointed object, such as a paper clip, into the emergency
eject hole, and push with hand. (Typical required force is 59N [6.0kg])
After removing the caddy from the drive unit, consult your dealer or qualified service personnel.
s General Host interface Read Function Acceptable discs: SCSI-2, single ended, 50 pin CD-ROM mode-1 data discs CD-ROM XA discs CD-Audio discs Audio-combined CD-ROM discs CD-I discs CD-I Ready Discs Photo CD (Single and Multi session) Video CD CD-R discs (Conforming to Orange Book Part II) CD-ROM Mode-1 CD-ROM XA CD-Audio Audio-combined CD-ROM CD-I Video CD CD-Text Disc at once Session at once Track at once Variable packet writing (Packet size : max. 2 Mbyte) Fixed packet writing (Packet size : max. 2 Mbyte) Multi-session 2 Mbyte 12 cm(8cm Read Only) 600 min-1 (600 rpm) at CLV = 1.4 m/s (1x) 1200 min-1 (1200 rpm) (2x) 2400 min-1 (2400 rpm) (4x) 4240 min-1 (4240 rpm) (8x) 200 min-1 (200 rpm) at CLV = 1.2 m/s (1x) 400 min-1 (400 rpm) (2x) 800 min-1 (800 rpm) (4x) 1600 min-1 (1600 rpm) (8x)
Write Function Applied Format:

Writing Method:

Cache memory(R/W) Disc diameter: Rotational speed Innermost track:

Outermost track:

s Drive performance Data transfer rate Sustained rate: 150 kbytes/s (1x) 300 kbytes/s (2x) 600 kbytes/s (4x) 1200 kbytes/s (8x) 5 Mbytes/s (asynchronous) 10 Mbytes/s (synchronous) 500 ms (typical/1x) 450 ms (typical/2x) 400 ms (typical/4x) 350 ms (typical/8x) 350 ms (typical/1x) 300 ms (typical/2x) 250 ms (typical/4x) 220 ms (typical/8x)
SCSI Interface Burst rate: Access time Full stroke:

Average:

s Reliability Read error rate (includes retry, normal disc) L-EC on: 1 Block / bits (double) L-EC off: 1 Block / 109 bits (double) s Audio Output level Line out: Head phone: s Environmental conditions Temperature and humidity Operating 5 C to 40 C(41F to 104 F) (no condensation) Transportation 40 C to 60 C(40 F to 140 F), 10 % to 90 % (within 72 hours, no condensation) Storage 30 C to 50 C(22 F to 122 F, 10 % to 90 % (within 6 months, no condensation) Temperature and humidity gradients 10 C/hour, 10 %/hour Vibration Operating Read: 1.96 m /s 2 (0.2 G o-p) at 5 Hz to 300 Hz (sweep) Write: 0.98 m /s 2 (0.1G o-p) at 5Hz to 300 Hz(sweep) 0.7 V at 47 k 0.55 V at 32

Non-operating Transportation Shock Operating
19.6 m /s2 (2 G o-p) at 7 Hz to 300 Hz 1.44 m2 /s3 -Hz (0.015 G2 /Hz) at 5 Hz to 50 Hz Read: 49 m /s2 (5 G o-p) at 11 ms half sine wave (includes 5 retries) Write:4.9 m/s2 (0.5 G o-p) at 11ms half sine wave 490 m /s2 (50 G o-p) at 11ms half sine wave 76 cm drop (with standard individual package) 146.0 x 41.4 x 203.0 mm ( w / h / d ) (5 3/4 x 1 5/8 x 8 inches) 1.0 kg +5 V 5 % DC and +12V DC 10 % +5 V: 0.05 Vp-p +12 V: 0.1 Vp-p +5 Vdc +12 Vdc 700 mA (Typ) < 900 mA (Max) 500 mA (Typ) < 800 mA (Max) 760 mA (Typ) < 1000 mA (Max) 1000 mA (Typ) < 1400 mA (Max) 760 mA (Typ) < 1000 mA (Max) 900 mA (Typ) < 1400 mA (Max) 500 mA (Typ) < 800 mA (Max) 120 mA (Typ) < 200 mA (Max)
Non-operating Transportation s Dimensions and weight Dimensions Mass s Power requirement Voltage Ripple Current Hold track state

Seeking

+5 Vdc +12 Vdc

Spin up/Write

Stand by
s Connectors Power-in/Interface connector Audio connectors Molex 53450-5411 or equivalent Molex 50460-4A or equivalent
s Laser Type Wave length Output power Beam divergence s Supplied accessory Users Guide Disc Caddy OPA-2000 s Optional accessories CD ROM discs: YHDS-50 CD-ROM Test Disc Type 1.3 (equivalent to YHDS-4) YHDS-100 CD-ROM Test Disc Type 2.0" (audio-combined) OPA-2000 (1 each) (1 each) Semiconductor laser GaAlAs 778 to 787nm (at 25 C 2 C) 2.5 mW (Read) 60 mW (Write) 60 degree
Additional caddies: s Crystal frequency
33.8688 MHz 34.5744 MHz Design and specifications are subject to change without notice.
Diese Ausrstung erfllt die Europischen EMC-Bestimmungen fr die Verwendung in folgender / folgenden Umgebung(en): Wohngegenden Gewerbegebiete Leichtindustriegebiete (Diese Ausrstung erfllt die Bestimmungen der Norm EN55022, Klasse B.)

s Dimension diagram

Important: Screws must not extend more than 4.0mm into the side panels or the bottom plate.

USB SCSI Adapter with Termpower

P73276

F5U015-TPW
Introduction and System Requirements
Thank you for purchasing the Belkin Components USB-SCSI Adapter. Now, you can easily add up to 7 SCSI devices on your Windows 98 PC, or Mac through USB port! No more opening your computer case, no more IRQ conflicts or driver problems! Simply plug it in!

Your PC must have:

486 processor or faster 16MB memory or more A free USB port (on the computer or at a hub) Windows 98 or Windows 98 SE
Your Macintosh must have:
OS 8.6 or higher A free USB port (on the computer or at a hub)

Notes:

It is NOT recommended that you plug in the USB-SCSI adapter to the USB ports on the iMac keyboard. The keyboard does not supply enough power, and is a low-speed device. 2. If you own a non-iMac machine and wish to add USB ports, please obtain a Belkin USB BusPort for Mac (model # F5U005-Mac) Your SCSI device must be able to supply termination power to the USB SCSI Adapter. Some devices such as Iomega Zip Drives and some brands of scanners will not be able to provide the required +5V termination power. In such an event, a SCSI device that can provide termination power must be connected to the device chain or you can use the power supply adapter supplied with the package. If you are going to plug the USB-SCSI Adapter into a USB Hub, make sure that it is a self-powered hub. (A self-powered hub has its own power supply.) 1 1.

Package Contents

Belkin Components USB SCSI Adapter withTermpower CD containing both Windows and Macintosh drivers Power supply adapter (7.5VDC, 600mA) with DB25 adapter Registration card This manual
Macintosh Installation and Usage

MACINTOSH INSTALLATION:

1. Insert the Belkin USB to SCSI Adapter with Termpower CD into your CD-ROM drive. Double-click on the CD icon. You will see two folders: MAC Driver and PC Driver. Double click on the "MAC Driver" folder. Now, you will see two files named: "Belkin USB-SCSI" "Belkin USB-SCSI SIM" 2. Double click on your "Hard Drive" icon and look for "System Folder". Double click on "System Folder". 3. In "System Folder", look for another folder called "Extensions". Once you have located the "Extensions" folder, you will need to select the two files in the Belkin USB to SCSI CD (see #1 above), and drag the two files onto the "Extensions" folder. You will see your system copying both files over.

USAGE:

1. When copying is finished connect your SCSI device or device chain to the USB SCSI Adapter. See appendices for adapters and cables you may need. Make sure that the devices are powered up. Plug in the USB SCSI Adapter to a free USB port on your computer, or USB Hub. Restart your computer. To do this click on "Special" at the top menu bar, and choose "Restart". 2. After restart, icons of your SCSI device(s) should appear on your desktop.
Macintosh Installation and Usage (continued)
If you unplug the USB SCSI Adapter from the computer, or the device(s) from the SCSI chain, the operating system may not recognize this and might think that the device(s) are still connected. In the event that the device(s) and/or the USB-SCSI Adapter is unplugged from the computer, and an application tries to access the device(s), your computer will hang. You must cycle power in order to recover your system. Hence, to disconnect a device from the SCSI chain, always drag its icon to the TRASH first, then disconnect the USB SCSI Adapter or devices.
Windows 98 Installation and Usage

WINDOWS 98 INSTALLATION:

1. Connect your SCSI device or device chain to the USB SCSI Adapter. See appendices for adapters and cables you may need. Make sure that the device(s) are powered up. 2. Plug in the USB SCSI Adapter to a free USB port on your computer, or USB Hub. A "New Hardware Found" dialog box will appear:

Click on NEXT.

Even if the Adapter is plugged into your USB port (or Hub), it must first be plugged into a SCSI device that provides termination power, before Windows will detect and enumerate the Adapter, and the SCSI device(s). If your SCSI device(s) does not provide termination power, make sure the power supply adapter that came with the package is connected. 5

Windows 98 Installation and Usage (continued)
3. On the screen that appears select "Search for the best driver for your device (Recommended)", and then click Next. 4. Windows will now prompt you for drivers. Insert the Belkin USB SCSI Adapter CD-ROM in your CD-ROM drive. Put a check mark at the box named "Specify a location:". Type D:\PC Driver. (In this example, D is the driver letter for the CD-ROM drive; it may be different on your computer, you may need to check it.) Click Next.
5. Windows will automatically find and install the drivers from the CD-ROM, and display the next dialog box, confirming it has loaded the correct files:
Click on NEXT. 6. Lastly, Windows will display this final dialog box.
Click FINISH. Windows will then detect the "USB Mass Storage Class Adapter", and automatically install its drivers. There will be no more prompts. 7

Appendices

Troubleshooting
The SCSI device(s) connected to the USB-SCSI Adapter is not detected by my computer. Make sure the SCSI device(s) are powered up and at least one device provides termination power necessary for the Adapters operation. If you are just connecting one device and that device does not have termination power, make sure the power supply adapter provided with the package is connected. The SCSI device(s) must be powered up AND connected to the Adapter prior to plugging into the USB port. If you are using a USB Hub or composite device that has a built-in hub, make sure that the device is self-powered, providing the full 500mA of current required by the Adapter. After shutting down your computer, try unplugging then plugging in the Adapter from the USB port. Try unplugging the Adapter, turn the power off and back on of the SCSI device(s), then plugging the Adapter back into the USB port. Restart your computer with the Adapter connect to the USB port, and all the SCSI device(s) powered up.
Belkin External SCSI Cross-Reference Table
This is only a partial listing of our most common SCSI Cable Assemblies. Contact your Belkin sales representative for assistance in choosing the cable you need.
Belkin USB to SCSI Uninstall
To uninstall the USB to SCSI Adapter, do the following: Note: Do not unplug the Belkin USB to SCSI from the

computer until completing the following.

A. For PC

1. Right click on the "My Computer" icon on your desktop. Select Properties then Device Manager. Look for "Universal serial bus controller", click on the "Plus" sign beside it, highlight "Belkin eUSB SCSI Adapter" then click Remove. Click OK. Close Device Manager. 2. Click on Start/Find/Files and Folders. Under "Named" type Bel*.*, under "Look In" put it on the C drive then click on "Find Now". Delete all the four items that will appear namely: Beluscsi.sys, Belsmsd.pdr, Belsmsd, and Belkin Component. 3. You can now unplug the Belkin USB to SCSI adapter from the computer. Restart your computer.

B. For Mac

1. Double click on your "Hard Drive" icon and look for "System Folder/Double click on "System Folder". 2. In "System Folder", look for another folder called "Extensions". Under "Extensions" look for the following files: "Belkin USB-SCSI" and "Belkin USB-SCSI SIM". Drag these 2 files to the Trash Bin. 3. You can now unplug the Belkin USB to SCSI adapter from the computer. Restart your computer.

Information

FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY
We, Belkin Components, of 501 West Walnut Street, Compton CA 90220, declare under our sole responsibility that the product: F5U015-TWP to which this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CE Declaration of Conformity
We, Belkin Components, declare under our sole responsibility that the F5U105-TWP, to which this declaration relates, is in conformity with Generic Emissions Standard EN50081-1 and with Generic Immunity Standard EN500A1-1 1992.
Belkin Components Limited Lifetime Product Warranty
Belkin Components warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced. THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty. BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING, OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH BELKIN PRODUCTS. Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties, so the above limitations of exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

Compatibility List

A. Devices that work Stand-alone " SCSI Hard Drives Seagate ST31220A - 2GB Seagate ST51080N - 1GB Microtech P-E-2000 - 2GB " SCSI Removable Media Drives Coniglio MO 230MB ( FujitsuDrive M2512A ) Fujitsu 640 Dyna MO - M2513A - F/W: 1300 Fujitsu 640 Dyna MO SE - M2513EL - F/W: 0010 Iomega Jaz - 1 GB F/W J.66 Iomega Jaz - 2GB F/W E.17 Olympus 640 MO - S350 - F/W: 1.20 SCSI - Panasonic PD device - LF 1000 SyQuest SQ270 - 270MB " SCSI CDD\CDR\CD-Changer Sony 4X - CDU 76S SCSI CDD F/W 1.0a. NAKAMICHI 4 tray CD-Changer - MJ 4.8 NEC Multispin 4x - 7 tray CD-Changer - NRC MBR - 7.4 Sanyo CRD-254S F/W 1.02 Philips Omniwriter26 (Ricoh) F/W 2.03 Sony CDR CDU948S F/W 1.0h Philips CDD2600 F/W 1.07 Plextor DX-327S F/W 1.02 Teac CD-532S 1.0a " SCSI Tape drives Exabyte 8585S F/W 06M0 Conner-TR4 CTT- 8000IS F/W 1.17 HO-C1533A F/W 9503 Microtech MicroDAT 8000
Compatibility List (cont.)

"

SCSI Scanners HP 5P C5110A F/W 3638 Pixelcraft Pro Image 2400 Scanner UMAX ProLook 2000 Other Microtech Digital PhotoAlbum - PC Card Reader Microtech Digital PhotoAlbum.p - PC Card Reader Microtech Digital PhotoAlbum Pro - PC Card Reader SCM Microsystems (Intermart) PCD-10 SCM Microsystems (Intermart) PCD-15 SCM Microsystems (Intermart) PCD-25
B. Devices that work on a SCSI chain/or may require the included power adapter and DB25 adapter " SCSI Hard Drives Seagate ST31220A - 2GB Seagate ST51080N - 1GB Microtech P-E-2000 - 2 GB " SCSI Removable Media Drives Iomega Jaz - 1 GB F/W J.66 Iomega Jaz - 2GB F/W E.17 Iomega Zip 100 (SCSI) F/W J.66 Fujitsu 640 Dyna MO - M2513A - F/W: 1300 Fujitsu 640 Dyna MO SE - M2513EL - F/W: 0010 Olympus 640 MO - S350 - F/W: 1.20 SCSI - Panasonic PD device - LF 1000
SyQuest SQ270 - 270MB SCSI CDD\CDR\CD-Changer Sony 4X - CDU 76S SCSI CDD F/W 1.0a. NAKAMICHI 4 tray CD-Changer - MJ 4.8 NEC Multispin 4x - 7 tray CD-Changer - NRC MBR - 7.4 Sanyo CRD-254S F/W 1.02 Philips Omniwriter26 (Ricoh) F/W 2.03 Sony CDR CDU948S F/W 1.0h Philips CDD2600 F/W 1.07 Plextor DX-327S F/W 1.02 Teac CD-532S 1.0a SCSI Tape drives Exabyte 8585S F/W 06M0 Conner-TR4 CTT- 8000IS F/W 1.17 HO-C1533A F/W 9503 Microtech MicroDAT 8000 SCSI Scanners HP 5P C5110A F/W 3638 Pixelcraft Pro Image 2400 Scanner UMAX Power Look 2000 Other Microtech Digital PhotoAlbum - PC Card Reader Microtech Digital PhotoAlbum.p - PC Card Reader Microtech Digital PhotoAlbum Pro - PC Card Reader SCM Microsystems (Intermart) PCD-10 SCM Microsystems (Intermart) PCD-15

SCM Microsystems (Intermart) PCD-25 C. Currently incompatible devices " Nikon LS-2000 Film Scanner (Super Coolscan 2000) " Microtech Digital PhotoAlbum_P (Old MP01625) " Microtech Digital PhotoAlbum (Old MP01610A) " UMAX Power Look III

belkin.com

Belkin Components
501 West Walnut Street Compton CA 90220 USA Tel: 310.898.1100 Fax: 310.898.1111

Belkin Components, Ltd.

Unit 13 Gatelodge Close Round Spinney Northampton Northants NN3 8RX UK Tel: +44 (0) 1604678300 Fax: +44 (0) 1604678330

Belkin Components B.V.

Diamantlaan WV Hoofddorp The Netherlands Tel: +31 (0) 235698765 Fax: +31 (0) 235612694
2000 Belkin Components. All rights reserved. All trade names are registered trademarks of respective manufacturers listed.