3-859-005-11 (1)
FM/AM Compact Disc Player
Operating Instructions Manual de instrucciones ############

EN ES C

For installation and connections, see the supplied installation/connections manual. Con respecto a la instalacin y las conexines, consulte el manual de Instalacin/ conexiones suministrado. ##### #####

CDX-4160

1997 by Sony Corporation

Actual total number:

Sony CDX-4160 (E,S,C,A) 3-859-005-11(1)

Welcome !

Thank you for purchasing the Sony Compact Disc Player. This unit lets you enjoy a variety of features. You can use an optional rotary remote (RM-X2S).

Table of Contents

Getting Started
Resetting the unit.. 4 Detaching the front panel.. 4 Setting the clock.. 5

Additional Information

Precautions... 9 Maintenance.. 9 Dismounting the unit.. 10 Attaching the label to the rotary remote. 10 Location of controls.. 11 Specifications... 12 Troubleshooting guide.. 13 Index.. 14

CD Player

Listening to a CD.. 5 Playing a CD in various modes. 6
Memorizing stations automatically Automatic Memory.. 6 Memorizing only the desired stations. 7 Receiving the memorized stations.. 7

Other Functions

Adjusting the sound characteristics.. Muting the sound.. Changing the sound and beep tone.. Turning on the clock display Power Select Function.. 8 8
Attaching the front panel

Resetting the unit

Before operating the unit for the first time or after replacing the car battery, you must reset the unit. Press the reset button with a pointed object, such as a ball-point pen.
Align part A of the front panel to part B of the unit as illustrated, and push until it clicks.
Reset button Notes Pressing the reset button will erase all the memorized program and memory functions. When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you insert a disc. Do not insert a disc within these 10 seconds, otherwise, the unit will not be reset, and you will have to press the reset button again.
Notes Be sure not to attach the front panel upside down. Do not press the front panel hard against the unit when attaching it. Press it lightly against the unit. Do not press hard or put excessive pressure on the display window of the front panel. Do not expose the front panel to direct sunlight, heat sources such as hot air ducts, and do not leave it in a humid place. Never leave it on the dashboard of a car parked in direct sunlight where there may be a considerable rise in temperature.

Caution alarm

If you turn the ignition key switch to the OFF position without removing the front panel, the caution alarm will be activated and a beep tone will be heard for a few seconds (only for cars with an accessory position on the ignition key switch). If you connect an optional power amplifier and do not use the built-in amplifier, the beep tone will be disabled.
Detaching the front panel
You can detach the front panel of this unit to prevent the unit from being stolen.
Press (OFF). Press (RELEASE) to open up the front panel, and detach the panel by pulling it towards you.
(RELEASE) Notes Be sure not to drop the panel when detaching it from the unit. If you press (RELEASE) to detach the panel while the unit is still on, the unit will turn off automatically to prevent the speakers from being damaged. When you carry the front panel with you, put it in the supplied front panel case.

Setting the clock

The clock has a 12-hour digital indication. Example: Set the clock to 10:08

Listening to a CD

Simply insert the CD. Playback starts automatically.

Labelled side up

Press (OFF) or (DSPL) during operation. Press (DSPL) for two seconds.

The hour digit flashes.

1 Set the hour digits.

To go forward To go back

2 Press (SEL) momentarily.
If a CD is already inserted, press (SOURCE) repeatedly until CD appears.

MIN SEC

Getting Started/CD Player
Elapsed playing time Note To play back an 8 cm CD, use the optional Sony compact disc single adapter (CSA-8).

The minute digits flash.

3 Set the minute digits.
To Stop playback Eject the CD

Press 6 or (OFF) 6

Press (DSPL) momentarily.
Changing the displayed items
Each time you press (DSPL), the item changes as follows:
z Elapsed playing time Time Z z Track number

The clock is activated.

Note If the car has no accessory position on the ignition key switch, the clock cannot be set unless the power is turn on. Set the clock after you have turned on the radio, or started CD playback.
Locating a specific track Automatic Music Sensor (AMS)
During playback, press either side of (SEEK/AMS) momentarily.
To locate succeeding tracks

SEEK AMS

To locate preceding tracks
Locating a specific point in a track Manual Search
During playback, press and hold either side of (SEEK/AMS) for two seconds. Release the button when you have found the desired point.

To search forward

Memorizing stations automatically

Automatic Memory

Stations with the clearest reception are automatically searched and memorized on each band (FMI, FMII, FMIII and AM). Up to 6 stations on each band can be stored on the number buttons ((1) to (6)) in the order of band frequency.
To search backward Note If _ _ or _ _ appears in the display, you have reached the beginning or the end of the disc and you cannot go any further.
Playing a CD in various modes
EN Searching for the desired track Intro Scan
Press (1) during playback. INTRO appears in the display. The first 10 seconds of all the tracks are played. When you find the desired track, press again. The unit returns to the normal playback mode.
Press (SOURCE) repeatedly to select the tuner. Each time you press (MODE), the mode changes as follows:

CD TUNER

Press (MODE) repeatedly to select the band. Each time you press (MODE), the mode changes as follows:

FMI FMII FMIII AM

Playing tracks repeatedly Repeat Play
Press (2) during playback. REPEAT appears in the display. When the currently played track is over, it will be played again from the beginning. To cancel this mode, press again.
Press (A.MEM) for two seconds. The unit will be starts scanning the selected band and memories the tuned stations on the number button (1) through (6) automatically.
Playing tracks in random order Shuffle Play

Press (3) during playback. SHUFFLE appears in the display. To cancel this mode, press again.
Notes The unit does not store stations with weak signals. If only a few stations are received, some number buttons remain empty. When a number is indicated in the display, the unit starts storing stations from the one currently displayed. If a CD is not in the unit, only the tuner band appears even if you press (SOURCE).
Memorizing only the desired stations
You can store up to 6 stations on each band (18 for FMI, FMII and FMIII, 6 for AM) in the order of your choice.
Tip If you know the frequency of the station you want to listen to, press and hold either side of (SEEK/AMS) for two seconds until the desired frequency appears (manual tuning).
If FM stereo reception is poor Monaural Mode
Press (SENS) momentarily until MONO appears. The sound improves, but becomes monaural (ST disappears). To go back to the normal mode, press again until MONO disappears.
Press (SOURCE) repeatedly to select the tuner. Press (MODE) repeatedly to select the band. Press either side of (SEEK/AMS) to tune in the station that you want to store on the number button. Press the desired number button ((1) to (6)) for two seconds until MEM appears. The number button indication appears in the display.
Each time you press (DSPL), the items alternate between the frequency and time.

CD Player/Radio

Note If you try to store another station on the same number button, the previously stored station will be erased.
Receiving the memorized stations
Select the desired band (page 6). Press the number button ((1) to (6)) momentarily where the desired station is stored.
If you cannot tune in a preset station
Press either side of (SEEK/AMS) momentarily to search for the station (automatic tuning). Scanning stops when the unit receives a station. Press either side of (SEEK/AMS) repeatedly until the desired station is received.
Note If the automatic tuning stops too frequently, press (SENS) momentarily until LCL appears in the display (local seek mode). Only the stations with relatively strong signals will be tuned in.
Digital D-BASS Level Level

Analog D-BASS

D-BASS 3 D-BASS 2 D-BASS 1
Adjusting the sound characteristics
You can adjust bass, treble, balance and fader. Each source can store the bass and treble level independently.

Frequency (Hz)

Adjusting the bass curve Turn the D-BASS dial to adjust the bass level (1, 2 or 3). D-BASS appears in the display. During CD playback, DIGITAL D-BASS appears in the display. To cancel, turn the dial to the OFF position.

Select the item you want to adjust by pressing (SEL) repeatedly. VOL (volume) n BAS (bass) n TRE (treble) n BALANCE (balance) n FADER (fader)

Muting the beep tone

Press (6) while pressing (SEL). To obtain the beep tone again, press these buttons again.
Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep tone will be disabled.
Adjust the selected item by pressing (+) or (). Adjust within three seconds after selecting the item. (After three seconds, the buttons work as volume control buttons.)

Muting the sound

Press (MUTE). MUTE flashes. To restore the previous volume level, press (MUTE) again.
Turning on the clock display Power Select Function
Only for cars with an accessory position on the ignition key switch To turn the Power Select Function ON
Changing the sound and beep tone
Boosting the bass sound D.bass
You can enjoy clear and powerful bass sound. The D-bass function boosts the low frequency signal with a sharper curve than conventional bass boost. You can hear the bass line more clearly even if the vocal sound is the same volume. You can emphasize and adjust the bass sound easily with the D-bass control. This effect is similar to the one you get when you use an optional subwoofer system. Moreover, the Digital D-bass* function creates even sharper and more powerful bass sound than Analog D-bass.
Press (OFF) while pressing (SEL). The Power Select Function ties the clock display power to the accessory position on the ignition key switch. To avoid battery wear, the clock is not displayed while the unit is initializing.
Note You cannot operate this function with the optional rotary remote (RM-X2S).
* Digital D-bass is available during CD playback.

Precautions

If your car was parked in direct sunlight resulting in a considerable rise in temperature inside the car, allow the unit to cool off before operating it. If no power is being supplied to the unit, check the connections first. If everything is in order, check the fuse. If no sound comes from the speakers of a two-speaker system, set the fader control to the center position. If your car is equipped with a power antenna, note that it will extend automatically while the unit is operating. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer.

Before playing, clean the discs with an optional cleaning cloth. Wipe each disc from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray intended for analog discs.
Notes on moisture condensation
On a rainy day or in a very damp area, moisture may condense on the lenses inside the CD player. Should this occur, the unit will not operate properly. In this case, remove the disc and wait for about an hour until the moisture evaporates.

When you play 8 cm CDs

Use the optional Sony compact disc single adapter (CSA-8) to protect the CD player from being damaged.
Other Functions/Additional Information

Notes on handling CDs

A dirty or defective disc may cause sound dropouts while playing. To enjoy optimum sound, handle the disc as follows. Handle the disc by its edge. To keep the disc clean, do not touch the surface.

Maintenance

Fuse replacement
When replacing the fuse, be sure to use one that matches the amperage described on the fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
Do not stick paper or tape on the labeled surface.

Fuse (10 A)

Do not expose the discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in the temperature inside the car.
Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit.

Cleaning the connectors

The unit may not function properly if the connectors between the unit and the front panel are not clean. To prevent this, open the front panel by pressing (RELEASE), then detach it and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged.
Attaching the label to the rotary remote
You can control this unit with the optional rotary remote (RM-X2S). Several labels are supplied with the rotary remote. Attach the label that matches the functions of this unit and the mounting position of the rotary remote. After you mount the rotary remote, attach the label in the illustration below.

Main unit

DSPL MODE SEL

Back of the front panel

SEL MODE DSPL

Dismounting the unit

Release key (supplied)

Location of controls

SOURCE

D-BASS

RELEASE

REPEAT

Refer to the pages for details. 1 SEEK/AMS (seek/Automatic Music Sensor/manual search) button 5, 6, SOURCE (source select) button 5, 6, MODE (band select) button 6, SEL (control mode select) button 5, DSPL (display mode change/time set) button 5, Display window 7 SENS (sensitivity adjust) button 6 (eject) button A.MEM (Automatic Memory) button 6 ! RELEASE (front panel release) button 4, 10 ! (+) () (volume/bass/treble/balance/ fader control) buttons 5, 8 ! MUTE button 8 ! Reset button (located on the front side of the unit hidden by the front panel) 4 ! OFF button 4, 5, 8 ! Frequency Select switch (located on the bottom of the unit) See Frequency Select Switch in the Installation/Connections manual. ! During radio reception: Number buttons 6, 7 During CD playback: (1) INTRO button 6 (2) REPEAT button 6 (3) SHUF button 6 ! D-BASS dial 8 When the positions of switch ! have been changed, be sure to press the reset button after connecting power.

Specifications

CD player section
System Signal-to-noise ratio Frequency response Wow and flutter Compact disc digital audio system 90 dB 10 20,000 Hz Below measurable limit

General

Outputs Line output (2) Power antenna relay control/Power amplifier control lead Bass 10 dB at 100 Hz Treble 10 dB at 10 kHz 12 V DC car battery (negative ground) Approx. 180 mm (w/h/d) Approx. 163 mm (w/h/d) Approx. 1.3 kg Parts for installation and connections (1 set) Front panel case (1) Rotary remote RM-X2S RCA pin cord RC-63 (1 m), RC-64 (2 m), RC-65 (5 m) Cleaning cloth XP-CD1 Compact disc single adapter CSA-8
Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories Optional accessories

Tuner section

Tuning range FM tuning interval: 50 kHz/200 kHz switchable 87.5 108.0 MHz (at 50 kHz step) 87.5 107.9 MHz (at 200 kHz step) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 0.5 % (stereo), 0.3 % (mono) Separation 35 dB at 1 kHz Frequency response 30 15,000 Hz Capture ratio 2 dB
Design and specifications are subject to change without notice.
Tuning range AM tuning interval : 9 kHz/10 kHz switchable 531 1,602 kHz (at 9 kHz step) 530 1,710 kHz (at 10 kHz step) External antenna connector 10.71 MHz/450 kHz 30 V

Antenna terminal Intermediate frequency Sensitivity

Power amplifier section

Outputs Speaker outputs (sure seal connectors) Speaker impedance ohms Maximum power output 35 W 4 (at 4 ohms)

Troubleshooting guide

The following checklist will help you remedy the problems that you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.
Problem No sound. Cause/Solution Adjust the volume with (+). Set the fader control to the center position for two-speaker systems. The power cord or battery has been disconnected. The reset button has been pressed. n Store the settings again into the memory.
The contents of the memory have been erased.
Indications do not appear in the Remove the front panel and clean the connectors. See Cleaning display. the connectors (page 10) for details. No beep tone. An optional power amplifier is connected and you are not using the built-in amplifier. The beep tone is muted (page 8).

CD playback

Problem CD cannot be loaded. Play does not begin. CD is automatically ejected. CD will not eject. The operation buttons do not function. The sound skips due to vibration. Cause/Solution Another CD is already loaded. The CD was forcibly inserted upside down. Dusty disc. The ambient temperature is more than 50C. Press the 6 button for two seconds. Press the reset button. The unit is installed at an angle of more than 20. The unit is not installed in a sturdy part of the car.

Radio reception

Problem Preset tuning is not possible. Automatic tuning is not possible. The ST indication flashes. Cause/Solution Store the correct frequency. The broadcast signal is too weak. The broadcast signal is too weak. n Use manual tuning. Tune in the frequency correctly. The broadcast signal is too weak. n Set to the MONO mode (page 7).

Error displays

The following indications will flash for about five seconds. Display Cause A CD is dirty or inserted upside down. The CD player cannot be operated because of some problem. Solution Clean or insert the CD correctly. Press the reset button or 6.
If the above-mentioned solutions do not help improve the situation, consult your nearest Sony dealer.
Automatic Memory 6 Automatic Music Sensor (AMS) Automatic tuning 7 5

M, N, O

Manual search 6 Manual tuning 7 Memorizing a station Monaural mode 7 Mute 8 6

Antes de iniciar a reproduo, limpe os discos com um pano de limpeza (venda avulsa). Limpe o disco no sentido indicado pelas setas. No utilize solventes tais como benzina, diluentes, produtos de limpeza disponveis no mercado ou aerosis anti-estticos destinados a discos de gravao analgica.

Installation

Choose the mounting location carefully, observing the following: The unit is not subject to temperatures exceeding 55C (such as in a car parked in direct sunlight). The unit is not subject to direct sunlight. The unit is not near heat sources (such as heaters). The unit is not exposed to rain or moisture. The unit is not exposed to excessive dust or dirt. The unit is not subject to excessive vibration. The fuel tank should not be damaged by the tapping screws. There should be no wire harnesses or pipes under the place where you are going to install the unit. The spare tire, tools or other equipment in or under the trunk should not be interfered with or damaged by the screws or the unit itself. Be sure to use only the supplied mounting hardware for a safe and secure installation. Use only the supplied screws. Make holes of 3.5 mm only after making sure there is nothing on the other side the mounting surface.

Instalacin

Elija cuidadosamente el lugar de montaje, teniendo en cuenta lo siguiente: La unidad no queda sometida a temperaturas superiores a los 55C (como en un automvil aparcado a la luz solar directa). La unidad no queda sometida a la luz solar directa. La unidad no queda cercana a fuentes trmicas (como aparatos de calefaccin). La unidad no queda expuesta a la lluvia o a la humedad. La unidad no queda expuesta a polvo o suciedad excesivos. La unidad no queda sometida a vibraciones excesivas. El depsito de combustible no deber daarse con los tornillos autorroscantes. No deber haber mazos de conductores ni tubos debajo del lugar donde vaya a instalar la unidad. La rueda de repuesto, las herramientas, u otros equipos situados dentro o debajo del portaequipajes no debern verse interferidos ni daados por los tornillos ni por la propia unidad. Para realizar una instalacin segura, emplee solamente la ferretera de montaje suministrada. Utilice slo los tornillos suministrados. Antes de hacer los orificios de 3,5 mm, compruebe que no haya nada en el otro lado de la superficie de montaje.

Montering

Var noga vid monteringslgets val. Observera fljande: Utstt inte enheten fr temperaturer som verstiger 55C (som t ex i en bil parkerad i direkt solljus). Utstt inte enheten fr direkt solljus. Placera inte enheten i nrheten av vrmekllor (som varmluftsventler m.m.). Undvik att enheten utstts fr regn eller fukt. Undvik att enheten utstts fr mycket damm eller smuts. Undvik att enheten utstts kraftiga vibrationer eller skakningar. Att brnsletanken inte skadas nr du drar t de sjlvgngande skruvarna. Att det inte finns ngra kabelhrvor, rr, ledningar eller slangar under platsen dr CD-skivvxlaren monteras. Att reservdcket, verktygen i bagageutrymmet eller delarna under det inte skadas nr du drar t skruvarna eller av CD-vxlare. Var noga med att endast anvnda de medfljande monteringstillbehren fr att vara sker p att CD-skivvxlaren monteras ordentligt och p ett korrekt stt. Anvnd endast medfljande skruvar. Kontrollera frst att det inte finns ngot p andra sidan monteringsytan som kan ta skada nr du borrar hlen ( 3,5 mm).