CDX-GT34W
CD Receiver MP3/WMA/AAC Player
Play CDs, CD-Rs, and CD-RWs, including discs loaded with MP3's 1 and WMA files. The front auxiliary input lets you connect almost any portable audio device to your car's sound system. 13 Segment black LCD with negative display for viewing information. The optional XA-120IP allows users to connect, charge, and control your compatible iPod2 device directly from the receiver. Experience bass-pumping sound compliments of the 52 watts of peak power delivered to all four speakers (208 watts total power). The Satellite Radio ready head unit integrates seamlessly with satellite radio Sony Bus adapters so you can receive digital satellite radio broadcasts. HD Radio ready4 capability lets you receive digital audio broadcasts when used with an optional HD Radio tuner. A built-in LPF (Low Pass Filter) and HPF (High Pass Filter) work to deliver overall better sound, and the LPF features a phase shift function that reduces low-end reverberation. Boost your car's sound system with minimal effort and maximum flexibility by using the two pre-outs to add a subwoofer and external amplifier, or another audio component, to your Xplod system Radio Data System (RDS) feature displays radio broadcast information such as artist, title, and album. The included Wireless Card Remote allows you control the basic functions of your Sony Xplod system while keeping your eyes on the road.

Features

MP3/WMA Playback1 Play CDs, CD-Rs, and CD-RWs, including discs loaded with MP3's1 and WMA files. Detachable Faceplate with Front Panel Aux In The front auxiliary input lets you connect almost any portable audio device to your car's sound system. iPod2 adaptor support The optional XA-120IP allows users to connect, charge, and control your compatible iPod2 device directly from the receiver. SAT Radio3 /HD Radio4 ready The Satellite Radio ready3 head unit integrates seamlessly with satellite radio Sony Bus adapters so you can receive digital satellite radio broadcasts. HD Radio ready4 capability lets you receive digital audio broadcasts when used with an optional HD Radio tuner. EQ3 Stage 2 and 52 Watts x 4 High Power Experience basspumping sound compliments of the 52 watts of peak power delivered to all four speakers (208 watts total power). Front & Rear/Sub switchable pre amp output with LPF/HPF A built-in LPF (Low Pass Filter) and HPF (High Pass Filter) work to deliver overall better sound, and the LPF features a phase shift function that reduces low-end reverberation. Boost your car's sound system with minimal effort and maximum flexibility by using the two pre-outs to add a subwoofer and external amplifier, or another audio component, to your Xplod system ADDITIONAL FEATURES Black 13 segment LED display Radio Data System (RDS) Supplied wireless card remote (RM-X151) Blue Key Illumination

Convenience

Tilt Range: 45

Amplifier Section

Speaker Impedance: 4-8 Ohms Max power output: 52 watts x 4 at 4 ohms
FM Usable Sensitivity: 10 dBf Selectivity: 75 dB at 400 kHz S/N Ratio: 70 dB (mono) Frequency Response: FM: 20-15,000 Hz Stereo Separation: 40 dB at 1 KHz
Power Consumption (in Operation): 45w Output Power: 52W x4 High Power - 17 watts per channel minimum continuous average power into 4 Ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. Current Drain: 3 - 5 amps Input Voltage: 12 V DC car battery (negative ground)

Inputs and Outputs

RCA Audio Output(s): Front and Rear/Sub selectable RCA preamp outputs Antenna Terminal(s): Aerial Input Terminal 12V Trigger Output(s): Power antenna Amplifier turn on Audio In: Front Aux input with variable level: -8dB +18dB Rear Sony Bus audio / controll terminal Infrared Port: Wireless remote

Dimensions

Weight: 1.2Kg Measurements: 178 x 50 x 179mm

Supplied Accessories

Parts for installation and connections (1 set) RM-X151 wireless remote

Specifications

Convenience Features
CD Text Display: CD and MP3 / WMA data displayed Illumination: Blue On-Screen Clock: 12H

Optional Accessories

Replacement remote: RM-X151 CD changer (10 discs): CDX-M757MX CD changer (6 discs): CDX-T69 Source selector: XA-C40 Aux-in selector: XA-300 iPod interface adaptor: XA-120IP HD Radio tuner: XT-100HD Color: Gun Metallic / Black UPC Code: 027242774063
1.Not all MP3, WMA, AAC files may playback due to file variations. Copyright protected ACC-LC files cannot be played back. 2.iPod connectivity requires optional adaptor (XA-120IP). 3. Satellite radio service requires a satellite radio tuner and service subscription, sold separately. 4.HD Radio capability requires an optional HD Radio tuner (XT-100HD). 2009 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony, Walkman, Xplod, and the Sony and Xplod logos are trademarks of Sony. iPhone and iPod are trademarks of Apple Inc., registered in the U.S. and other countries. All other trademarks are trademarks of their respective owners. Features and specifications are subject to change without notice. Non-metric weights and measures are approximate.

General

Disc Capacity: 1 Color: Gun Metallic / Black
Preout Impedance: 220 ohms Preout Voltage: 2 volt Frequency Response: CD: 10-20,000 Hz Wow and Flutter: Below measurable limit Station Preset(s): 18 FM / 12 AM Digital-to-Analog Converter: 24bit Tuner Frequency Range: FM:Tuner Frequency Range(MHz): 87.5107.9, AM:Tuner Frequency Range(kHz): 530-1710 Tone Control(s): Low +/- 10 dB at 60 Hz Mid +/- 10 dB at 1 kHz High +/- 10dB at 10 kHz Tuner Type: SSIR-EXA with RDS Volume Control: Tel/Nav Attenuation Circuitry CD Playback: CD, CD-R / CD-RW (MP3/WMAfiles) Band: AM / FM Signal-to-Noise Ratio (dB): CD: 120 dB
Please visit the Dealer Source for current information at www.sony.com/dealersource Sony Electronics Inc. 16530 Via Esprillo San Diego, CA 92127 1.800.222.7669 www.sony.com Last Updated: 04/13/2011

CDX-M620/M670

SERVICE MANUAL

Ver 1.0 2001. 03

US Model
AEP Model UK Model E Model

CDX-M670

The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism CD Drive Mechanism Type
CDX-M700R/M750 MG-383Z-121//K KSS-720A

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CD player section
Signal-to-noise ratio 90 dB Frequency response 10 20,000 Hz Wow and flutter Below measurable limit Laser Diode Properties (US model) Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block.

Optical Pick-up Name

MW/LW (AEP, UK, E model) Tuning range MW: 531 1,602 kHz LW: kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 V LW: 40 V

Power amplifier section

Outputs Speaker outputs (sure seal connectors) Speaker impedance ohms Maximum power output 52 W 4 (at 4 ohms)

General

Outputs Audio outputs (front/rear) Subwoofer output (mono) Power antenna relay control lead (US model) Power aerial relay control lead (AEP, UK, E model) Power amplifier control lead

Tuner section

FM Tuning range 87.5 107.9 MHz (US model) 87.5 108.0 MHz (AEP, UK, E model) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 8 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 66 dB (stereo), 72 dB (mono) Harmonic distortion at 1 kHz 0.6% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 15,000 Hz AM (US model) Tuning range Antenna terminal Intermediate frequency Sensitivity

Continued on next page

FM/AM COMPACT DISC PLAYER
530 1,710 kHz External antenna connector 10.7 MHz/450 kHz 30 V
FM/MW/LW COMPACT DISC PLAYER

9-873-505-11

2001C0400-1 2001. 3

Sony Corporation

Audio Entertainment Group General Engineering Dept.

Inputs

Tone controls Loudness Power requirements Dimensions Mounting dimensions Mass Supplied accessories
Telephone ATT control lead Illumination control lead BUS control input connector BUS audio input connector Antenna input connector (US model) Aerial input connector (AEP, UK, E model) AUX IN connector (US model) Bass 8 dB at 100 Hz Treble 8 dB at 10 Hz +8 dB at 100 Hz +2 dB at 10 Hz 12 V DC car battery (negative earth) Approx. 182 mm (w/h/d) Approx. 160 mm (w/h/d) Approx. 1.5 kg Parts for installation and connections (1 set) Front panel case (1) Card remote commander RM-X110 (US model) RM-X111 (AEP, UK, E model)

US model: CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block.

optical pick-up block

This unit cannot be connected to a digital preamplifier or an equalizer. Design and specifications are subject to change without notice.

semi-fixed resistor

SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

5. EXPLODED VIEWS

5-1. 5-2. 5-3. 5-4. 5-5. 5-6. 5-7. 5-8. Chassis Section... 56 Cam Section... 57 Main Board Section... 58 Front Panel (Key) Assy Section.. 59 Front Panel (Dspl) Assy Section.. 60 CD Mechanism Section (1).. 61 CD Mechanism Section (2).. 62 CD Mechanism Section (3).. 63
6. ELECTRICAL PARTS LIST.. 64
CDX-M620/M670 SECTION 1 GENERAL

US MODEL

This section is extracted from instruction manual.

AEP, UK, E MODEL

US, AEP, UK, E MODEL

US MODEL Connection

AEP, UK, E MODEL Connection
CDX-M620/M670 SECTION 2 DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
2-2. FRONT PANEL ASSY (INOPERATIVE)
Front Panel Assy (Normal) Front Panel Assy (Inoperative)
CD Mechanism Block, Front Panel (KEY) Assy

4 screw (panel)

Sub Panel (CD) Sub Assy Chassis (T) Sub Assy
Motor Block Assy, Cam (R) Assy Lever Section Servo Board Shaft Roller Assy

Main Board

Heat Sink

Floating Block Assy

Optical Pick-up Block

flexible board

2 front panel (DSPL) assy 6 front panel (key) assy (Take care not to pull the flexible board excessively)

3 screw (panel)

Note : Follow the disassembly procedure in the numerical order given.
2-1. FRONT PANEL ASSY (NORMAL) 2-3. CD MECHANISM BLOCK, FRONT PANEL (KEY) ASSY
1 Turn on the power and open the front panel. 7 bracket (CD) 5 CD mechanism block 6 PTT 2.6xtension spring (flexible) 5 screw (panel) 0 cover (flexible)
9 slider (flexible) 3 PTT 2.6x4 qa CN604
slider (flexible) flexible board
screw (panel) 2 PTT 2.6x4
Note: When installing the flexible board, make the board slack as illustrated.
1 PTT 2.6xfront panel (key) assy (Take care not to pull the flexible board excessively) 4 CN401 qa front panel (key) assy
3 front panel (DSPL) assy
2-4. SUB PANEL (CD) SUB ASSY

1 CN603

4 claw 3 PTT 2.6x6

5 claw 2 PTT 2.6 x6

6 sub panel (CD) sub assy
2-5. MOTOR BLOCK ASSY, CAM (R) ASSY
Note : Install the motor block assy and cam (R) assy in this roder. For phase alignment between cams (L) and (R), see page 22 and 24. 1 PTT 2.6xPTT 2.6xmotor block assy
Note: Install the cam (R) assy with the cam fully rotated in the direction of the arrow A.

2 cam (R) assy 3 CN602

2-6. MAIN BOARD

5 MAIN board

4 PTT 2.6x6 ground point

3 PTT 2.6x6 ground point

2 PTT 2.6x6

1 PTT 2.6x6

2-7. HEAT SINK

5 heat sink

4 PTT 2.6x6

3 PTT 2.6x10

2 PTT 2.6xPTT 2.6x6
2-8. CHASSIS (T) SUB ASSY

2 P 2xP 2x3

1 Unsolder the lead wires.

IC5 CXP84640-072Q (CD SYSTEM CONTROL) (SERVO BOARD) Pin No. Pin Name I/O 1 ITRPT Not used in this set. 2, 3 4, 11 12, 13 14, NCO OPEN CLOSE LINKOFF NCO D SW SSTP NCO EMPH O CDMON CD ON A MUT LD ON CD RST HOLD AGC CONT PH3 TSTIN0 TSTIN1 TST.CLV NCO RESET X IN X OUT GND XT OUT XT IN AVSS AVREF TEP L TEP H SLED PH2 SEK/SMET GFS/MNT2 SEL SC-JIG ON/OFF SCLK LOCK SCK2 SI2 BUS CLK BUS SI BUS SO F OK GFS TEST MODE I O I I I O O O O O O O O I I I I I I O O I I I I I I I I I O I/O O I I/O I O I I I Not used in this set. Not used in this set. Front panel open detection input Front panel close control output Bus interface link input Not used in this set. Down switch input (SW1) Limit switch input (SW4) Not used in this set. Not used in this set.

Pin Description

De-emphasis ON/OFF control output CD mechanism deck power control output CD power control output System attenuate control output Laser power ON/OFF control output CD system reset output Hold switch output AGC control output Not used in this set. Not used in this set. Not used in this set. Not used in this set. Not used in this set. Not used in this set. System reset input (L=Reset) Xtal oscillator input from system clock. (10 MHz) Xtal oscillator output for system clock. (10 MHz) Analog ground Not used in this set. Not used in this set. A/D converter ground A/D converter reference voltage input Not used in this set. Not used in this set. Sled drive input Not used in this set. Fixed at H in this set. Fixed at H in this set. Fixed at H in this set. CD-TEXT data read clock output Lock signal input/output Not used in this set. Sub Q read clock output Sub Q 80 bit, PCM peak and level data 16 bit input. Not used in this set. Bus system serial clock input/output Bus system serial interface input Bus system serial interface output Focus OK signal input GFS signal detection input Fixed at H in this set.

Pin No. 80

Pin Name SENS BU.IN BUSON IN SW SELF SW SCOR CD-CKO LM LOD CD DATA CD-XLAT LM-EJ DRV-OE MD2 VDD NIH V/Z PH1 DOUT-SEL

I/O I I I I I O O O O O O O O I I I I
Pin Description SENS signal input Not used in this set. Not used in this set. Back-up power detection input Bus on control input Disc in switch input (SW3) Self switch input (SW2) Sub-code sync output CD signal process serial clock output Loading motor control output CD signal process serial data output CD signal process serial data latch output Loading motor control output Focus/tracking coil/sled motor control output Digital out ON/OFF control output (L: OFF, H: ON) Power supply pin Fixed at H in this set. Fixed at H in this set. Not used in this set. Not used in this set. Fixed at H in this set. Not used in this set.
IC501 MB90574BPMT-G-321-BND (SYSTEM CONTROL) (MAIN BOARD) (US MODEL) IC501 MB90574BPMT-G-322-BND (SYSTEM CONTROL) (MAIN BOARD) (AEP, UK, E MODEL) Pin No. Pin Name I/O Pin Description 13 (NCO) O Not used. (Open) 56 SP LATCH ATT SYS RST (NCO) VCC (NCO) E2P SIO E2P CKO FLS SI FLS SO BUS ON BEEP TEL ATT UNI SI UNI SO UNI CKO (NCO) SIRCS DSP SI DSP SO DSP CKO DSP PLL DSP MST (NCO) VOL ATT TU ATT VSS C DSP LAT DSP RST SHIFT DVCC DVSS FP CTRL (NCO) AVCC AVRH AVRL AVSS KEY IN0 KEY IN1 RC IN0 (NCO) QUALITY (NCO) MPTH VSM VCC STBY NS MASK O O O O O I/O I/O I O O O I I O O O I I O O O O O O O O O O O O I I I O I O I I O O Spectrum analyzer data latch signal System mute signal System reset signal Not used. (Open) Power supply pin (+5 V) Not used. (Open) Tuner unit EEPROM BUS serial data input/output Tuner unit EEPROM BUS serial clock input/output Flash CPU write-in data input Flash CPU write-in data output BUS ON signal Beep signal Telephone mute signal SONY BUS serial data input SONY BUS serial data output SONY BUS serial clock output Not used. (Open) Wireless remote data input DSP serial data input DSP serial data output DSP serial clock output DSP PLL clock control signal DSP master/slave control signal Not used. (Open) Electronic volume mute signal Not used. (Open) Ground Not used. (Open) DSP latch signal DSP reset signal OSC frequency shift signal for DC/DC conv. Power supply pin (+5 V) Ground OPEN/CLOSE motor voltage control signal Not used. (Open) Power supply pin (+5 V) Power supply pin (+5 V) Ground Ground Key input 0 Key input 1 Rotary commander input 0 Not used. (Open) Noise detection signal Not used. (Open) Tuner multi path detection signal S-meter voltage detection signal Power supply pin (+5 V) Power amplifier drive signal Noise detection ON/OFF control signal

Pin No. 110 111

Pin Name DDC ON CD EJECT OK CD OPEN REQ (NCO) OPEN KEY NOSE SW VSS DETACH SW PWM (NCO) FLASH W I2C SIO I2C CKO RC IN1 X1A X0A DAVN CDON IN BU IN DSP READY KEY ACK AD ON ACC IN FLS PWON PW ON TEST IN RAM BU HSTX MD2 MD1 MD0 RSTX VSS X0 X1 VCC ILL IN I DET MOT MOT + CLOSE SW OPEN SW CENT SW (NCO) CDMD SEL DEST SEL1 DEST SEL2 BOOT (NCO) DSP ON SENS ON EMPH IN PACK IN

Spectrum analyzer data latch signal Back-up power detection signal Ground Not used. (Open) BUS ON signal Power supply pin (+5 V) Not used. (Open) Ground Spectrum analyzer data select signal Illumination select control signal 1 Illumination select control signal 2 Not used. (Open) Not used. (Open) Link OFF control signal Not used. (Open) Illumination power control signal Ground Not used. (Open) Display CPU write-in control signal Power supply pin (+5 V) Not used. (Open) LCD driver serial data output Spectrum analyzer data input Flash CPU write-in data input Spectrum analyzer clock input LCD driver serial clock output Ground LCD driver chip enable output Ground LCD driver inhibit control signal LCD driver chip enable output LCD driver chip enable output Not used. (Open) Flash write control signal Flash write enable signal System reset signal Non maskable interrupt signal

Pin No. 98 99, 126 128

Pin Name STBY VCC XTAL EXTAL VSS PF7 VCC PF6 PF0 UNI SO UNI SI VSS UNI CKI P53 AVCC VREF P40 P47 AVSS VSS P17 P10 MD0 MD1 MD2 PG0 PG2
I/O I O O O I I O I O I I I O
Pin Description Hardware standby signal Power supply pin (+5 V) Crystal oscillator (18.432 MHz) Crystal oscillator (18.432 MHz) Ground Not used. (Open) Power supply pin (+5 V) Not used. (Open) SONY BUS serial data output SONY BUS serial data input Ground SONY BUS serial clock input Not used. (Open) Power supply pin (+5 V) Power supply pin (+5 V) Connecting to ground in this set. Ground Ground Not used. (Open) Mode setting 0 Mode setting 1 Mode setting 2 Not used. (Open)
4-2. CIRCUIT BOARDS LOCATION

DISC IN SW board

LIMIT SW board SERVO board
tuner unit (TUX201) DISPLAY board MAIN board

SUB (CD) board KEY board

4-3. BLOCK DIAGRAM CD SECTION
OPTICAL PICK-UP KSS-720A A RF AMP, LD APC, ERROR AMP IC1 DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC501 CDL ATT CD SYSTEM CONTROL IC5 A MUT 19 OPEN 6 CLOSE 7 RF EQ RFO RFAC EFM DEM D/A I/F LOUT1 D/A LOUT2 CONV. 79 79

TUNER SECTION (Page 35)

SYSTEM CONTROL IC501 (1/3) 5 ATT 58 CD EJECT OK 59 CD OPENREQ 86 UNI CLK UNI SI UNI SO BUS ON SYS RST BU IN RAM BU RSTX SIRCS 24 HSTX IC502
Signal path :CD R-ch : same as L-ch.

C 7 B 6 I-V CONV.

(Page 36)

R-CH CD ON MD ON

BUS CLK 51 BUS SI 52

RDS DECODER IC202 RDSDET 9 X201 4.3MHz 16 MPX 4 OSCO 5 OSCI 20 LV IN SDA 9 SCL 10 MPTH 2 DAVN MPTH 75 DAVN
ST-BY TEL ATT ILL IN ACC IN X1A
73 X501 32.768kHz ACC CHECK Q405

Q406 ILLUM CHECK Q407

X0A 74
AEP,UK,E S METER 14 SDA 12 SCL 13 SDA 17 SCL S-METER 70 I2CSDA 71 I2CSCL 10 E2PSDA 11 E2PSCL TEST IN 84 PW ON 83 XXTUN ON 114 X503 3.68MHz 9V Q402

EEPROM

POWER CONT Q110,111

AUDIO 9V

BATT Q404

POWER CONT Q401

AMP REM ANT REM
Signal path : FM : AM/MW : CD R-ch : same as L-ch.

POWER CONT Q107,108

F901 TUNER 8V POWER CONT Q306-308 BATT

DC-DC CONVERTER 8 IC306

REG Q201

TUNER 5V

4-5. BLOCK DIAGRAM DISPLAY SECTION

(Page 35)

SUB SYSTEM CONTROL IC702 BUS SI UNI SO 98 UNI SI 97 UNI SO 101 UNI CKI 38 BUS ON 34 BU IN BUF 7 IC701 SA CLK 1 SA IN 112 SA CLK SA OUT

TUNER SECTION

AD ON SW QAD ON SYSTEM CONTROL IC501 (3/3)

BUS CLK BUS ON BU CHECK

S RST LINK OFF SIRCS D70
81 SYS RES 50 LINK OFF AEP,UK,E J651 (REMOTE IN) 72 RC INRC INKEY ACK
IR 16 RECEIVE 7 IC62 D908 IR 16 RECEIVE 7 IC901 LCD DRIVER ICXTAL 86 EXTAL X701 18.432MHz BOOT 57 LED SWLED SWRX 62 LCD SO/TX CEO INH CKO LCD CEI CE2 ILL ON 52

KEY IN MATRIX

46 KEY INKEY IN1
INH CLK DATA CEO DIMMER LED SW1
106 BOOT 116 LED SWLED SWRX 13 TX 82 FLSWPWON BATT M601 OPEN/CLOSE MOTOR 1 REG IC2 MT +B DDC ON 57

(Page 34)

CD SECTION
CD ON MD ON POWER CONT. Q117,118 VOLTAGE CHECK IC102 CD 6V REG Q114,1

LCD 9V

POWER CONT. Q60,61
DIMMER CONTLROL Q98 9V POWER CONT. Q109,112 LCD9V
9V 3 MOTOR DRIVE ICVREF CONT. Q651,652

REG Q119

CD 5V BATT REG Q113,116 BU 5V
LCD DRIVER IC61 CN902 ILL ON 9V TX (SO) RX (SI) FL SW LCD 9V I DET 7 IC650

INH CLK DATA CE1

98 MOT+ 97 MOT

MT +B BEEP DRIVE Q502

40 FPCRTL I DET Q650 SW1001 (OPEN/CLOSE) D903 (DISC IN) LED DRIVE Q901,902

BEEP 15

BZ501 POWER CONT. Q101,102
96 I DET DC/DC CONV. CONTROL ICOPEN SW 99 CLOSE SW

(X IN)

(XOUT)
4-6. PRINTED WIRING BOARDS CD MECHANISM SECTION
Semiconductor Location Ref. No. IC1 IC5 IC7 IC501 Q101 Location C-2 C-6 F-2 F-5 B-2

(Page 43)

Refer to page 37 for Waveforms. 4-7. SCHEMATIC DIAGRAM CD MECHANISM SECTION (1/2) Refer to page 54 for IC Block Diagrams.

IC B/D

(Page 41)

(Page 46)

Note: Voltage is dc with respect to ground under no-signal conditions. no mark : CD PLAY
Refer to page 37 for Waveforms. 4-8. SCHEMATIC DIAGRAM CD MECHANISM SECTION (2/2) Refer to page 54 for IC Block Diagrams.

(Page 40)

4-9. PRINTED WIRING BOARDS MAIN SECTION
Semiconductor Location Ref. No. Location Ref. No. D104 K-8 IC502 D107 E-2 IC650 D109 G-2 IC651 D202 C-13 IC652 D203 B-13 IC702 D204 G-8 IC801 D205 G-9 D302 B-7 Q101 D303 B-6 Q102 D304 B-6 Q105 D309 G-7 Q107 D311 C-7 Q108 D404 C-4 Q109 D406 D-4 Q110 D407 C-6 Q111 Q112 D503 H-6 Q114 D505 H-5 Q115 D506 J-8 Q116 D507 J-8 Q117 D509 I-8 Q118 D511 H-5 Q201 D602 F-5 Q202 D604 G-4 Q203 D605 F-5 Q301 D606 G-4 Q302 D609 G-7 Q303 D612 G-6 Q304 D650 I-2 Q305 D804 J-10 Q306 D807 H-10 Q307 Q308 IC101 F-2 Q309 IC102 D-2 Q310 IC201 G-9 Q312 IC202 F-13 Q401 IC301 G-8 Q402 IC302 F-9 Q404 IC303 C-11 Q405 IC304 C-11 Q406 IC305 E-10 Q407 IC306 E-8 Q602 IC307 D-9 Q651 IC308 D-9 Q652 IC310 C-12 IC501 I-6
Location J-9 J-2 I-3 I-3 I-12 I-9 F-2 F-1 E-3 H-4 G-4 K-9 F-4 E-4 K-8 D-2 E-2 E-2 G-1 G-1 C-13 H-10 G-9 B-10 B-9 B-11 B-10 B-11 E-8 E-7 E-8 C-8 C-7 C-8 C-4 D-5 D-5 D-6 D-7 D-6 G-5 J-3 I-3

(Page 50)

(Page 39)
(Page 48) Semiconductor Location Ref. No. D101 D102 D105 D106 D301 D305 Location E-3 F-3 D-1 E-2 B-7 B-8 Ref. No. D306 D307 D308 D401 D405 D501 Location B-8 B-8 B-8 B-3 C-5 B-2 Ref. No. D502 D504 D508 D510 D603 D607 Location H-4 I-4 H-4 G-4 G-5 G-4 Ref. No. D608 D610 D611 D651 D652 D801 Location G-7 B-2 B-2 I-3 J-4 J-12 Ref. No. D802 D803 D805 D806 IC309 Location J-10 J-5 J-10 J-11 A-7 Ref. No. IC601 IC701 Q103 Q106 Q113 Location G-5 I-12 E-2 F-2 E-1 Ref. No. Q119 Q501 Q502 Q603 Q650 Location F-1 I-5 G-14 G-5 I-2

32 VIN4

20 AGCCONT + VC 19 RF BOT
31 VIN4+ + VIN1/VREF SW 5V REG + + 24 VIN3

30 VREF-IN

29 VIN1-SW
VEE C 7 VC D 8 RF SUMMING AMP VC VEE 9 VEE VC ERROR AMP FOCUS + RF EQ AMP + VC +

18 RFTC

28 VREF-OUT

IC101 TL1451ACDB-E20

S.C.P DTC2 REFO INA2 INB2 VCC FB2

17 RF I

IC601 BA8270F-E2

16 RFO

VO2+ 10 LEVEL SHIFT VO2 11

VC F 10

15 RFE

VO1+ 12

+ E 11 VC 14 FE

VO1 13

+ VC VCC VEE VC

VC BUFFER

13 TE TRACKING ERROR AMP

VCC1 14

MAD PSWN

VIN1+A 17

20 VIN2

13 PAUSE DETECTOR

+ VIN1B VIN1 +B
16 RNF DRIVER CONTROL LOGIC DRIVER 15 NC 14 OUTNC 12 VREF

CLOCKED COMPARATOR

SIGNAL QUALITY DECODER 4 CLOCK CLOCK INTERFACE REGISTER DATA

NC 2 OUTM BATT 4 VCC 5

RDS/RDBS DEMODULATOR

RDS/RDBS DECODER

POWER SAVE

10 NC TSD 9 NC

TEST CONTROL

OSCILLATOR & CLOCK

IIC BUS SLAVE TRANSCEIVER

MRO MPTH

CLOSE 6

11 OPEN

MULTI PATH DETECTOR
POWER SUPPLY & RESET 57kHz 8th ORDER BAND-PASS FILTER

IC651 BA6288FS-E2

IC202 SAA6588T-V2-118

VIN1A 16 +

VIN1 15
+ 27 REG-OUT 26 REG-IN 25 VIN3+ LEVEL SHIFT 23 VINVIN2+ + 21 VIN2
16 VERF. +2.5V VCC REFERENCE VOLTAGE +2.5V SHORT CIRCUIT PROTECTION COMPARATOR + + VREF/2

BUS ON 1

BUS ON SWITCH RESET SWITCH BATTERY SWITCH

14 VCC

+ ERROR AMP2 VERF VERF VERF PWM COMPARATOR2

BATT 3

OUTPUT2
RESET BUS ON CLK IN BU IN

CLK 4 VREF 5 DATA 6

OUTPUT1

9 DATA IN 8 DATA OUT

S R LATCH

R U.V.L.O

PWM COMPARATOR1

TRIANGLE OSCILLATOR 3 4

+ ERROR AMP1 GND 7 8

IC102 RN5VD53AA-TL

IC305 TDA7406TR
OUTSWR OUTSWL OUTSSL OUTSSR

ACINRL ACINRF ACINRR

29 MIXER
MONO- MONOFADER FADER ACINLF 34 SWINR 35 SWINL 36 ACOUTR 37 ACOUTL 38 CREF 39 FRONT ACIN OUTPUT SELECTOR MAIN SECOND REAR SW

MONO- MONOFADER FADER

SUBWOOFER +PHASE CONTROL

VOICE BANDPASS HP

IIC-BUS

22 VDD 21 SCL 20 SDA

BASS SUPPLY TREBLE HIGH-CUT 19 GND 18 EXT-ATT PULSE FORMER QUAL 17 QUAL

PANEL (KEY) SUB ASSY, FRONT (M670:US) PANEL (KEY) SUB ASSY, FRONT (M620) PANEL (KEY) SUB ASSY, FRONT (AEP,UK,E) BUTTON (ENTER) BUTTON (EQ7) BUTTON (EJECT) BUTTON (SEEK) PLATE (RING), LIGHT GUIDE BUTTON (+/) BUTTON (SOURCE) BUTTON (CLOSE) CUSHION (ELECTROSTATIC) BUTTON (6 KEY) (US) BUTTON (6 KEY) (AEP,UK,E) BUTTON (MODE) (US)
3-230-479-11 BUTTON (MODE) (AEP,UK,E) A-3283-164-A KEY BOARD, COMPLETE (US) A-3283-176-A KEY BOARD, COMPLETE (AEP,UK,E)
1-804-349-11 DISPLAY PANEL, LIQUID CRYSTAL
5-5. FRONT PANEL (DSPL) ASSY SECTION

213 210

215 204
not supplied (DISPLAY board)

Ref. No. * 205 * * 208

Part No. 3-230-470-01 3-230-472-01 3-230-471-01 3-230-378-01 3-230-469-01
Description PANEL (FRONT BACK) SPRING (LOCK), TENSION LOCK (DETOUCH) SHEET, INSULATING SHEET (DSPL), REFLECTION

Ref. No. * 215 LCD60

Part No. 3-230-466-01 3-230-426-01 3-230-422-01 3-230-427-01 X-3380-903-1
Description HOLDER (LCD-DSPL) BUTTON (OPEN) PLATE (LOGO), LIGHT GUIDE BUTTON (RESET-DSPL) PANEL SUB (DSPL) ASSY, FRONT
3-230-467-01 PLATE (LCD-DSPL), LIGHT GUIDE 1-694-806-21 CONDUCTIVE BOARD, CONNECTION 3-230-468-01 SHEET (DSPL), DIFFUSION
3-230-423-01 FILTER (IR-DSPL) 3-232-858-01 CUSHION (LIGHT GUIDE PLATE) 1-804-348-11 DISPLAY PANEL, LIQUID CRYSTAL
5-6. CD MECHANISM SECTION (1) (MG-383Z-121//K)

253 257

259 251

264 255

255 263

261 260

Ref. No. * 259
Part No. 1-676-709-11 3-040-039-01 3-040-038-01 3-040-050-01 3-040-022-01 3-040-044-01 3-040-067-01 A-3301-980-A 3-040-037-01
Description DISC IN SW BOARD CHASSIS (T) SPRING (LR), TENSION LEVER (L) RETAINER (ROLLER), SHAFT ROLLER (S) LEVER (R) SHAFT ROLLER ASSY GUIDE (DISC)

Ref. No. 260 * 267 M903

Part No. 3-040-040-01 A-3294-809-A 3-221-779-01 3-040-034-01 3-040-042-01 3-043-880-01 3-044-206-11 3-231-392-01 A-3315-039-A
Description ARM (ROLLER) SERVO BOARD, COMPLETE BRACKET (MOTOR) SPRING (RA), TENSION WASHER RING (RA), RETAINING SCREW, SPECIAL PLATE (CD), SHIELD MOTOR SUB ASSY, LO (LOADING)
5-7. CD MECHANISM SECTION (2) (MG-383Z-121//K)

307 308

314 310

not supplied

312 313

Ref. No. 307

Part No. 3-040-025-01 3-040-031-01 3-040-056-01 3-040-024-01 3-040-054-01
Description ARM, CHUCKING DAMPER (T) LEVER (D) RETAINER (DISC) WHEEL (LW), WORM

1-500-329-21 INDUCTOR, FERRITE BEAD < IC >

* * * *

IC60 IC61 IC62
8-759-653-26 IC LC75878W 8-759-653-26 IC LC75878W 8-759-830-18 IC RRX9000-0601#1 < LIQUID CRYSTAL DISPLAY >
3-230-469-01 SHEET (DSPL), REFLECTION < CAPACITOR > LCD60 C60 C61 C62 C63 C64 C65 C66 C67 C70 C71 C72 C73 C74 C75 C76 C77 C78 C79 C80 C81 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-115-412-11 1-165-176-11 1-165-176-11 1-165-176-11 1-115-412-11 1-165-176-11 1-165-176-11 1-165-176-11 1-107-826-11 1-107-826-11 1-107-826-11 1-124-778-00 1-162-970-11 1-125-837-11 1-164-388-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < CONNECTOR > CN60 1-815-500-21 PLUG, CONNECTOR 15P < DIODE > D61 D62 D63 D64 D65 D66 D67 D68 D70 8-719-422-41 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 8-719-977-12 8-719-420-14 8-719-977-12 8-719-083-14 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE MA8051-L-TX KDZ6.8V KDZ6.8V KDZ6.8V KDZ6.8V KDZ6.8V MA8082-M(TX) KDZ6.8V RRX9000-0501 R60 R61 R62 R63 R64 R65 R66 R67 R68 R69 R70 R71 1-216-829-11 1-216-833-11 1-216-829-11 1-216-037-00 1-216-037-00 1-216-025-11 1-216-025-11 1-216-025-11 1-216-025-11 1-216-033-00 0.1uF 0.1uF 0.1uF 0.1uF 680PF 0.047uF 0.047uF 0.047uF 680PF 0.047uF 0.047uF 0.047uF 0.1uF 0.1uF 0.1uF 22uF 0.01uF 1uF 270PF 0.1uF 10% 10% 10% 10% 5% 10% 10% 10% 5% 10% 10% 10% 10% 10% 10% 20% 10% 10% 5% 10% 16V 16V 16V 16V 25V 16V 16V 16V 25V 16V 16V 16V 16V 16V 16V 6.3V 25V 6.3V 50V 16V 1-804-348-11 DISPLAY PANEL, LIQUID CRYSTAL < DIODE > LED60 LED62 LED63 LED64 LED65 LED66 LED67 LED68 LED69 8-719-079-49 8-719-076-58 8-719-076-58 8-719-076-58 8-719-076-58 8-719-076-58 8-719-076-58 8-719-076-58 8-719-076-58 LED LED LED LED LED LED LED LED LED LWT673-R1S2-34 (SONY) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT) NSSW440-BRS (LCD BACK LIGHT)
< SWITCH > LSW60 1-771-883-11 SWITCH, TACTILE (WITH LED) (OPEN) < TRANSISTOR > Q60 Q61 Q62 8-729-106-60 TRANSISTOR 2SB1132-T101-QR 8-729-038-67 TRANSISTOR KRC102S 8-729-904-66 TRANSISTOR DTD113EK-T-146 < RESISTOR > METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 4.7K 10K 4.7K 220 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-864-11 SHORT 1-216-033-00 METAL CHIP
Ref. No. R72 R73 R74 R76 R77 R78 R79 R80 R81 R82 R83 R84 R85 R86 R87 R88 R89 R90 R91 R92 R93 R94 R95 R96 R97 Part No. 1-216-811-11 1-216-805-11 1-216-864-11 1-216-841-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-817-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-841-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-825-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-817-11 1-216-864-11 1-216-846-11 1-216-850-11 1-216-033-00 Description METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP METAL CHIP < SWITCH > S60 1-771-884-11 SWITCH, TACTILE (WITH LED) (RESET) ************************************************************* * 1-676-709-11 DISC IN SW BOARD **************** < SWITCH > SW2 1-529-566-21 SWITCH, PUSH (1 KEY) (SELF) SW3 1-529-566-21 SWITCH, PUSH (1 KEY) (DISC IN) ************************************************************* * * A-3283-164-A KEY BOARD, COMPLETE (US) A-3283-176-A KEY BOARD, COMPLETE (AEP,UK,E) ******************** 1-694-807-21 1-694-808-21 3-230-486-01 3-230-487-01 3-230-488-01 CONDUCTIVE BOARD, CONNECTION CONDUCTIVE BOARD, CONNECTION HOLDER (LCD-KEY) PLATE (LCD-KEY), LIGHT GUIDE SHEET (LCD-KEY), DIFFUSION < CAPACITOR > C1 C2 C3 C4 C5 C6 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-115-412-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 680PF 0.047uF 10% 10% 10% 10% 5% 10% 16V 16V 16V 16V 25V 16V LED6 LED7 LED8 LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 8-719-078-39 LED LED LED LED LED LED LED LED LED LED CL-170SR-CD-T (RING ILLUMINATION) CL-170SR-CD-T (CLOSE) CL-170SR-CD-T (MODE) CL-170SR-CD-T (Z) CL-170SR-CD-T (OFF) CL-170SR-CD-T (DSPL/PTY) CL-170SR-CD-T (SCRL) CL-170SR-CD-T (ENTER) CL-170SR-CD-T (LIST) CL-170SR-CD-T (MENU) 0 47K 2.2K 2.2K 2.2K 2.2K 47K 2.2K 2.2K 2.2K 2.2K 0 120K 270K 220 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W LED1 LED2 LED3 LED4 LED5 8-719-079-26 8-719-079-26 8-719-078-39 8-719-078-39 8-719-078-39 LED LED LED LED LED NSSB440-WRST-THR (LCD BACK LIGHT) NSSB440-WRST-THR (LCD BACK LIGHT) CL-170SR-CD-T (RING ILLUMINATION) CL-170SR-CD-T (RING ILLUMINATION) CL-170SR-CD-T (RING ILLUMINATION) Ref. No. C7 C8 C9 C10 Part No. 1-165-176-11 1-165-176-11 1-164-156-11 1-162-974-11

1-216-864-11 SHORT 1-216-850-11 METAL CHIP 1-216-846-11 METAL CHIP < SWITCH >
1-762-944-12 SWITCH, DETECTION (SMALL TYPE) (DOWN) < VIBRATOR >
SW901 1-692-135-21 SWITCH, KEYBOARD (RESET) ************************************************************* * 1-681-375-11 SW BOARD ********** < SWITCH > SW1001 1-771-937-21 SWITCH, DETECTION (OPEN/CLOSE) SW1002 1-529-566-31 SWITCH, PUSH (1 KEY) (CENTER) ************************************************************* MISCELLANEOUS *************** 360 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US) 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) (AEP,UK,E) 1-777-246-41 CORD (WITH CONNECTOR) (ANT) 1-790-375-21 CORD (WITH CONNECTOR) (SUB OUT (MONO)) 1-757-775-11 CORD (WITH CONNECTOR) (AUX-IN (AUDIO)) 1-681-390-11 X-3378-480-1 1-676-707-11 1-677-182-11 8-820-103-03 FLEXIBLE BOARD CHASSIS (OP) ASSY (including M901) PICK-UP FLEXIBLE BOARD MOTOR FLEXIBLE BOARD PICK-UP, OPTICAL KSS-720A/K1RP
X1 1-781-758-21 VIBRATOR, CERAMIC (CHIP TYPE) (10MHz) X2 1-781-759-21 VIBRATOR, CERAMIC (CHIP TYPE) (16MHz) ************************************************************* * 1-681-373-11 SUB (CD) BOARD ************** < CAPACITOR > C903 C904 C905 C906 C907 C908 1-164-156-11 1-164-156-11 1-124-778-00 1-162-970-11 1-125-837-11 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 22uF 0.01uF 1uF 270PF 25V 25V 6.3V 25V 6.3V 50V

20% 10% 10% 5%

1-164-388-11 CERAMIC CHIP < FLAT CABLE >
1-783-268-11 CABLE, FLAT 11P < DIODE >
D901 D902 D903 D906 D907 D908
8-719-988-61 8-719-017-95 8-719-079-10 8-719-422-41 8-719-977-12
DIODE 1SS355TE-17 DIODE KDZ18V LED CL-220UB-X-TS (DISC IN) DIODE MA8051-L-TX DIODE MA8068-M-TX
F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A M601 X-3378-769-1 MOTOR ASSY (OPEN/CLOSE) M902 A-3301-985-A MOTOR ASSY, SLED (SLED) M903 A-3315-039-A MOTOR SUB ASSY, LO (LOADING) *************************************************************
8-719-083-14 DIODE RRX9000-0501 < FERRITE BEAD >
8-759-830-18 IC RRX9000-0601#1
ACCESSORIES & PACKING MATERIALS ******************************** 1-476-546-11 REMOTE COMMANDER (RM-X111) (AEP,UK,E) 1-476-546-21 REMOTE COMMANDER (RM-X110) (US) 3-230-446-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) (US) 3-230-447-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH,SPANISH) (US) 3-230-448-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH, SWEDISH,PORTUGUESE,GREEK, RUSSIAN) (AEP,UK,E) 3-230-449-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, GERMAN,FRENCH,ITALIAN, DUTCH) (AEP,UK,E) 3-230-549-01 LID, BATTERY CASE (for RM-X110/X111) X-3378-390-1 CASE ASSY (for FRONT PANEL) ************************************************************* ************** HARDWARE LIST ************** #1 #2 #3 #4 #5 #6 #7 #8 #9 #10 7-685-790-09 7-685-792-09 7-685-794-09 7-627-553-28 7-624-102-04 7-627-552-88 7-685-105-19 7-627-553-37 7-628-253-00 7-627-553-17 SCREW +PTT 2.6X4 (S) SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X10 (S) SCREW, PRECISION +P 2X2.5 STOP RING 1.5, TYPE -E SCREW, PRECISION +P 1.7X2.2 SCREW +P 2X8 TYPE2 NON-SLIT SCREW, PRECISION +P 2X3 TYPE3 SCREW, SPECIAL SCREW, PRECISION +P 2X2 TYPE414

PARTS FOR INSTALLATION AND CONNECTIONS ************************************** 3-014-370-21 3-916-012-01 7-682-160-01 X-3368-725-1 3-386-828-01 3-349-410-01 X-3366-405-1 3-230-445-01 3-934-325-01 1-465-459-21 FRAME, FITTING BRACKET (ND), FITTING ASSIST (US) SCREW +P 4X6 (US) SCREW ASSY, FITTING (US) SCREW, FITTING (AEP,UK,E) BUSHING (AEP,UK,E) SCREW ASSY (EXP), FITTING (AEP,UK,E) COLLAR SCREW (+K 5X8 TP) ADAPTOR, ANTENNA (AEP,UK,E)
3-030-929-01 SPRING, FITTING 1-776-207-72 CORD (WITH CONNECTOR) (POWER) (US) 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) (AEP,UK,E) 3-231-993-01 KEY (01)

404 403

#11 7-627-850-28 SCREW, PRECISION +P 1.4X3 #12 7-621-255-25 SCREW +P 2X4 *************************************************************

REVISION HISTORY

Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2001. 03 Description of Revision New