H:\Data Disk\2348403211\234840321CDXS2050VEUR\00GB+00COV-EUR.fm

masterpage:Right

2-348-403-21 (1)
FM/MW/LW Compact Disc Player
Operating Instructions Bedienungsanleitung Mode demploi Istruzioni per luso Gebruiksaanwijzing

GB DE FR IT NL

Wichtig! Bitte nehmen Sie sich etwas Zeit, um den Gerte-Pass vollstndig auszufllen. Dieser befindet sich auf der hinteren Umschlagseite dieser Bedienungsanleitung.
Si dichiara che lapparecchio stato fabbricato in conformit allart. 2, Comma l del D.M. 28.08. 1995 n. 548.
For installation and connections, see the supplied installation/connections manual. Zur Installation und zum Anschluss siehe die mitgelieferte Installations-/Anschlussanleitung. En ce qui concerne linstallation et les connexions, consulter le manuel dinstallation/ raccordement fourni. Per linstallazione e i collegamenti, fare riferimento al manuale di istruzioni per linstallazione e i collegamenti in dotazione. Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding "Installatie en aansluiting en".

CDX-S2050V CDX-S2050

2005 Sony Corporation

CDX-S2050C

CDX-S2050V/S2050C/S2050 2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB01INT-EUR.fm

masterpage:Left

Welcome !
Thank you for purchasing this Sony Compact Disc Player. You can enjoy your drive with the following functions. CD playback: You can play CD-DA and CD-R/CD-RW for audio use.
Radio reception: You can store up to 6 stations per band (FM1, FM2, FM3, MW and LW). BTM (Best Tuning Memory) function: the unit selects strong signal stations and stores them. RDS services: You can use FM station with Radio Data System (RDS).
Warning if your cars ignition has no ACC position After turning the ignition off, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain.
This label is located on the bottom of the chassis.
H:\Data Disk\2348403211\234840321CDXS2050VEUR\00GB+00COV-EURTOC.fm

Table of Contents

Getting Started
Resetting the unit. 4 Setting the clock. 4 DEMO mode. 4 Detaching the front panel. 4 Attaching the front panel. 5

Other functions

Changing the sound settings. 9 Adjusting the sound characteristics BAL/FAD/SUB. 9 Adjusting the equalizer curve EQ3. 9 Adjusting setup items SET. 9 Using optional remote commanders. 10 Card remote commander RM-X114. 10 Rotary commander RM-X4S. 10
Location of controls and basic operations

Main unit. 6

Additional Information
Precautions. Notes on discs. Maintenance. Removing the unit. Specifications. Troubleshooting. Error displays/Messages. 14
Storing and receiving stations. 7 Storing automatically BTM. 7 Storing manually. 7 Receiving the stored stations. 7 Tuning automatically. 7 RDS. 7 Overview. 7 Setting AF and TA/TP. 8 Selecting PTY. 8 Setting CT. 8
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm

DEMO mode

When the unit is turned off, the clock is displayed first, then demonstration (DEMO) mode starts the demonstration display. To cancel the DEMO mode, set DEMO-OFF in setup (page 9) while the unit is turned off.

Resetting the unit

Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Detach the front panel and press the RESET button with a pointed object, such as a ballpoint pen.

Detaching the front panel
You can detach the front panel of this unit to prevent theft.
RESET button Note Pressing the RESET button will erase the clock setting and some stored contents.

Caution alarm

If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used.

Setting the clock

The clock uses a 24-hour digital indication.
Press and hold (SEL). The setup display appears. Press (SEL) repeatedly until CLOCKADJ appears. Press (DSPL). The hour indication flashes.
Press (OFF). The unit is turned off. Press , then pull it off towards you.
Press the volume +/ button to set the hour and minute. To move the digital indication, press (DSPL). Press (SEL). The clock starts and the next setup display appears. Press and hold (SEL). The setup is complete.
Notes Do not drop or put excessive pressure on the front panel and display window. Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Tip When carrying the front panel, use the supplied front panel case.
To display the clock, press (DSPL). Press (DSPL) again to return to the previous display.
Tip You can set the clock automatically with the RDS feature (page 8). With the card remote commander In step 2 and 4, to select the item or setting, press M or m. In step 4, to move the digital indication, press < or ,.
Attaching the front panel
Engage part A of the front panel with part B of the unit, as illustrated, and push the left side into position until it clicks.
Note Do not put anything on the inner surface of the front panel.

Main unit

SOURCE MODE

qh qj qk

CDX-S2050V CDX-S2050C CDX-S2050
Refer to the pages listed for details. a Volume +/ button To adjust volume. b SEL (select) button 4, 9 To select items. c SOURCE button To power on/change the source (Radio/CD). d MODE button 7 To select the radio band (FM/MW/LW). e Disc slot Insert the disc (label side up), playback starts. f Display window g ATT (attenuate) button To attenuate the sound. To cancel, press again. h EQ3 (equalizer) button 9 To select an equalizer curve (XPLOD, VOCAL, CLUB, JAZZ, NEW AGE, ROCK and CUSTOM). i Z (eject) button To eject the disc. j SEEK +/ button Radio: To tune in stations automatically (press); find a station manually (press and hold). CD: To skip tracks (press); fast-forward/reverse a track (press and hold). k (front panel release) button 4 l DSPL (display)/DIM (dimmer) button 4, 7 To change display items (press); change the display brightness (press and hold). m SENS/BTM button 7 To improve weak reception: LOCAL/MONO (press); start the BTM function (press and hold). n RESET button (located behind the front panel) 4 o Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD: (3): REP To play the current track/disc repeatedly. (4): SHUF To play the tracks in random order. p PTY (Programme Type) button 8 To select PTY in RDS. q AF (Alternative Frequencies)/TA (Traffic Announcement) button 8 To set AF and TA/TP in RDS. r OFF button To power off/stop the source. s Receptor for the card remote commander 10

Storing and receiving stations

Caution

When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident.
Tip If you know the frequency of the station you want to listen to, press and hold (SEEK) +/ to locate the approximate frequency, then press (SEEK) +/ repeatedly to fine adjust to the desired frequency (manual tuning).

Overview

FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio programme signal.
Storing automatically BTM 1
Press (SOURCE) repeatedly until TUNER appears. To change the band, press (MODE) repeatedly. You can select from FM1, FM2, FM3, MW or LW. Press and hold (BTM) until BTM flashes. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored.

Display items

A Radio band, Function B Frequency*1 (Station name), Clock, RDS data C TA/TP*2
*1 While receiving the RDS station, * is displayed on the left of the frequency indication. *2 TA flashes during traffic information. TP lights up while such a station is received.

Storing manually 1

While receiving the station that you want to store, press and hold a number button ((1) to (6)) until MEM appears. The number button indication appears in the display.
To change display items B, press (DSPL).

RDS services

This unit automatically provides RDS services as follows: AF (Alternative Frequencies) Selects and retunes the station with the strongest signal in a network. By using this function, you can continuously listen to the same programme during a long-distance drive without having to retune the same station manually. Provides current traffic information/programmes. Any information/ programme received, will interrupt the currently selected source.
Note If you try to store another station on the same number button, the previous stored station will be replaced. Tip When an RDS station is stored, the AF/TA setting is also stored (page 8).

Receiving the stored stations 1
Select the band, then press a number button ((1) to (6)). TA (Traffic Announcement)/ TP (Traffic Programme)
With the card remote commander To select preset stations, press M or m.

Tuning automatically 1

Select the band, then press (SEEK) +/ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received.
PTY (Programme Displays the currently Types) received programme type. Also searches your selected programme type. CT (Clock Time) The CT data from the RDS transmission sets the clock. continue to next page t
Notes Depending on the country/region, not all RDS functions may be available. RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data.
Local Link function (UK only)
This function enables you to select other local stations in the area, even if they are not stored on your number buttons. 1 During FM reception, press a number button ((1) to (6)) on which a local station is stored. 2 Within 5 seconds, press again a number button of the local station. Repeat this procedure until the local station is received.

Setting AF and TA/TP 1

Press (AF/TA) repeatedly until the desired setting appears.

Select

AF-ON TA-ON AF, TA-ON AF, TA-OFF
activate AF and deactivate TA. activate TA and deactivate AF. activate both AF and TA. deactivate both AF and TA.

Selecting PTY 1

Press (PTY) during FM reception.
Storing RDS stations with the AF and TA setting
You can preset RDS stations along with the AF/ TA setting. If you use the BTM function, only RDS stations are stored with the same AF/TA setting. If you preset manually, you can preset both RDS and non-RDS stations with the AF/TA setting for each. 1 Set AF/TA, then store the station with BTM or manually.
The current programme type name appears if the station is transmitting PTY data.
Press (PTY) repeatedly until the desired programme type appears. Press (SEEK) +/. The unit starts to search for a station broadcasting the selected programme type.
With the card remote commander In step 2, to select the programme type, press M or m.

Type of programmes

NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Popular Music), ROCK M (Rock Music), EASY M (Easy Listening), LIGHT M (Light Classical), CLASSICS (Classical), OTHER M (Other Music Type), WEATHER (Weather), FINANCE (Finance), CHILDREN (Childrens Programmes), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary)

Note You cannot use this function in countries/regions where no PTY data is available.
Presetting the volume of traffic announcements
You can preset the volume level of the traffic announcements so as to not miss hearing them. 1 Press the volume +/ button repeatedly to adjust the volume level. 2 Press and hold (AF/TA) until TA appears.
Receiving emergency announcements
With AF or TA on, the emergency announcements will automatically interrupt the currently selected source.
Staying with one regional programme REG
When the AF function is on: this units factory setting restricts reception to a specific region, so you will not be switched to another regional station with a stronger frequency. If you leave this regional programmes reception area, set REG-OFF in setup (page 9).
Note This function does not work in the UK and in some other areas.

Setting CT 1

Set CT-ON in setup (page 9).
Notes The CT function may not work even though an RDS station is being received. There might be a difference between the time set by the CT function and the actual time.
With the card remote commander In step 3, to adjust the selected item, press < or ,.
Changing the sound settings
Adjusting the sound characteristics BAL/FAD/SUB
You can adjust the balance, fader, and subwoofer volume.
Adjusting setup items SET
Press and hold (SEL). The setup display appears. Press (SEL) repeatedly until the desired item appears. Press the volume +/ button to select the setting (example ON or OFF). Press and hold (SEL). The setup is complete and the display returns to normal play/reception mode.
Press (SEL) repeatedly until BAL, FAD or SUB appears. The item changes as follows:
LOW* t MID* t HI* t BAL (left-right) t FAD (front-rear) t SUB (subwoofer volume)*2
*1 When EQ3 is activated (page 9). *2 When the audio output is set to SUB (page 9). ATT is displayed at the lowest setting, and can be adjusted up to 20 steps.
Note Displayed items will differ, depending on the source and setting. With the card remote commander In step 2, to select the setup item, press M or m. In step 3, to select the setting, press < or ,.

Press the volume +/ button repeatedly to adjust the selected item. After 3 seconds, the setting is complete and the display returns to normal play/reception mode.
The following items can be set (follow the page reference for details): z indicates the default settings. CLOCK-ADJ (Clock Adjust) CT (Clock Time) BEEP (page 4) To set CT-ON or CT-OFF (z) (page 7, 8). To set BEEP-ON (z) or BEEP-OFF.
Note Adjust within 3 seconds of selecting the item. With the card remote commander In step 2, to adjust the selected item, press < or ,.
Adjusting the equalizer curve EQ3
You can adjust and store the equalizer settings for different tone ranges.
REAR/SUB*1 To switch the audio output. REAR: to output to a power amplifier. SUB (z): to output to a subwoofer. DIM (Dimmer) To change the brightness of the display. DIM-ON: to dim the display. DIM-OFF (z): to deactivate the dimmer. ILM-1/ILM-2 (Illumination) (CDX-S2050C only) To change the illumination colour. ILM-1 (z): Amber ILM-2: Green
Select a source, then press (EQ3) repeatedly to select the EQ3 mode. Press (SEL) repeatedly until LOW, MID or HI appears. Press the volume +/ button repeatedly to adjust the selected item. The volume level is adjustable in 1 dB steps, from 10 dB to +10 dB.
Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold (SEL) before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode.
DEMO*1 To set DEMO-ON (z) or (Demonstration) DEMO-OFF (page 4). REG*2 (Regional) To set REG-ON (z) or REG-OFF (page 8). continue to next page t

LPF*3 (Low Pass Filter)

To select the cut-off frequency 78HZ, 125HZ or OFF (z).
Replacing the lithium battery
Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the card remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion.
*1 When the unit is turned off. *2 When FM is received. *3 When the audio output is set to SUB.
Using optional remote commanders
Card remote commander RM-X114

Location of controls

The corresponding buttons on the card remote commander control the same functions as those on this unit.
DSPL MENU* SOURCE </, (SEEK /+) SOUND OFF VOL (+/)

+ side up

MODE LIST*
Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur.

PRESET +

DISC +

SOURCE

PRESET

R ENTE

m/M (DISC*/ PRESET +/) ENTER* ATT

WARNING

The following buttons on the card remote commander have also different buttons/functions from the unit. </, (SEEK /+) buttons To control radio/CD, the same as (SEEK) +/ on the unit. (For details of other operations, see With the card remote commander on each pages.) SOUND button The same as (SEL) on the unit. M/m (DISC*/PRESET +/) buttons For details, see With the card remote commander on each pages.
* Not available for this unit. Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.
Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire.

Rotary commander RM-X4S

Attaching the label
Attach the indication label depending on how you mount the rotary commander.

SEL MODE DSPL

DSPL MODE SEL
The corresponding buttons on the rotary commander control the same functions as those on this unit.
ATT SEL PRESET MODE SOURCE DSPL VOL SEEK/AMS OFF

Precautions

If your car has been parked in direct sunlight, allow the unit to cool off before operating it. Power aerial will extend automatically while the unit is operating.

Moisture condensation

On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated.
The following controls on the rotary commander require a different operation from the unit. PRESET control To select preset stations (push in and rotate). VOL control The same as the volume +/ button on the unit (rotate). SEEK/AMS control The same as (SEEK) +/ on the unit (rotate, or rotate and hold).
To maintain high sound quality
Be careful not to splash juice or other soft drinks onto the unit or discs.

Notes on discs

To keep a disc clean, do not touch its surface. Handle the disc by its edge. Keep your discs in their cases or disc magazines when not in use. Do not subject discs to heat/high temperature. Avoid leaving them in a parked car or on a dashboard/rear tray. Do not attach labels, or use discs with sticky ink/residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc.

Changing the operative direction
The operative direction of the controls is factoryset as shown below.

To increase

To decrease
If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. 1 While pushing the VOL control, press and hold (SEL). Do not use any discs with labels or stickers attached. The following malfunctions may result from using such discs: Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism). Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp. Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs. You cannot play 8 cm CDs. continue to next page t
Before playing, clean the discs with a commercially available cleaning cloth. Wipe each disc from the centre out. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analogue discs.

Removing the unit

Remove the protection collar. 1 Detach the front panel (page 4). 2 Engage the release keys together with the protection collar.
Notes on CD-R/CD-RW discs
Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. You cannot play a CD-R/a CD-RW that is not finalized. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.
Orient the release keys as shown.
3 Pull out the release keys to remove the protection collar.

Maintenance

Fuse replacement
When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
Remove the unit. 1 Insert both release keys simultaneously until they click.

Hook facing inwards.

Fuse (10A)

Cleaning the connectors

The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 4) and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. 2 Pull the release keys to unseat the unit.

3 Slide the unit out of the mounting.

Back of the front panel

Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device.

Specifications

CD Player section
Signal-to-noise ratio: 120 dB Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit
Lead-free solder is used for soldering certain parts. (more than 80 %) Halogenated flame retardants are not used in the certain printed wiring boards. Halogenated flame retardants are not used in cabinets. Packaging cushions do not use polystyrene foam.

Tuner section

Tuning range: 87.5 108.0 MHz Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 kHz Usable sensitivity: 9 dBf Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz: 0.5 % (stereo), 0.3 % (mono) Separation: 35 dB at 1 kHz Frequency response: 30 15,000 Hz

Troubleshooting

The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures.
Tuning range: MW: 531 1,602 kHz LW: kHz Aerial terminal: External aerial connector Intermediate frequency: 10.7 MHz/450 kHz Sensitivity: MW: 30 V, LW: 40 V

General

No power is being supplied to the unit.

Power amplifier section

Outputs: Speaker outputs (sure seal connectors) Speaker impedance: ohms Maximum power output: 50 W 4 (at 4 ohms)
Check the connection. If everything is in order, check the fuse. If the unit is turned off and the display disappears, it cannot be operated with the remote commander. t Turn on the unit.
The power aerial does not extend.
Outputs: Audio outputs terminal (rear/sub switchable) Power aerial relay control terminal Power amplifier control terminal Inputs: Telephone ATT control terminal Remote controller input terminal Aerial input terminal Tone controls: Low: 10 dB at 60 Hz (XPLOD) Mid: 10 dB at 1 kHz (XPLOD) High: 10 dB at 10 kHz (XPLOD) Power requirements: 12 V DC car battery (negative earth) Dimensions: Approx. 178 mm (w/h/d) Mounting dimensions: Approx. 161 mm (w/h/d) Mass: Approx. 1.2 kg Supplied accessories: Parts for installation and connections (1 set) Front panel case (1) Optional accessories: Card remote commander: RM-X114 Rotary commander: RM-X4S

Design and specifications are subject to change without notice.
The power aerial does not have a relay box.

No sound.

The volume is too low. The ATT function is activated, or the Telephone ATT function (when the interface cable of a car telephone is connected to the ATT lead) is activated. The position of the fader control (FAD) is not set for a 2-speaker system.

No beep sound.

The beep sound is cancelled (page 9). An optional power amplifier is connected and you are not using the built-in amplifier.
The contents of the memory have been erased.
The RESET button has been pressed. t Store again into the memory. The power connecting lead or battery has been disconnected. The power connecting lead is not connected properly.
Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition key is switched.
The leads are not matched correctly with the cars accessory power connector. continue to next page t
The display disappears from/does not appear in the display window.
During FM reception, the ST indication flashes.
The dimmer is set DIM-ON(page 9). The display disappears if you press and hold (OFF). t Press and hold (OFF) again until the display appears. The connectors are dirty (page 12).
Tune in the frequency accurately. The broadcast signal is too weak. t Press (SENS) to set the monaural reception mode to MONO-ON.
An FM programme broadcast in stereo is heard in monaural.

CD playback

The disc cannot be loaded.
The unit is in monaural reception mode. t Press (SENS) until MONO-OFF appears.
Another disc is already loaded. The disc has been forcibly inserted upside down or in the wrong way.
The disc does not playback.
The SEEK starts after a few seconds of listening.
Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 12).

The sound skips.

The station is non-TP or has weak signal. t Deactivate TA (page 8).
No traffic announcements.
Installation is not correct. t Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc.
The operation buttons do not function. The disc will not eject.
Activate TA (page 8). The station does not broadcast any traffic announcements despite being TP. t Tune in another station.

PTY displays - - - - - - - -.
Press the RESET button (page 4).
The current station is not an RDS station. RDS data has not been received. The station does not specify the programme type.

Radio reception

The stations cannot be received. The sound is hampered by noises.

Error displays/Messages

Error displays
The following indications will flash for about 5 seconds, and an alarm sound will be heard.
Connect a power aerial control lead (blue) or accessory power supply lead (red) to the power supply lead of a cars aerial booster (only when your car has built-in FM/MW/LW aerial in the rear/side glass). Check the connection of the car aerial. The auto aerial will not go up. t Check the connection of the power aerial control lead. Check the frequency.
Preset tuning is not possible.
The disc is dirty or inserted upside down. t Clean or insert the disc correctly. The disc cannot play because of some problem. t Insert another disc.

FAILURE

Store the correct frequency in the memory. The broadcast signal is too weak.
Automatic tuning is not possible.
The speaker/amplifier connection is incorrect. t See the supplied installation/connections manual to check the connection.

OFFSET

Setting of the local seek mode is not correct. t Tuning stops too frequently: Press (SENS) until LOCAL-ON appears. t Tuning does not stop at a station: Press (SENS) repeatedly until MONOON or MONO-OFF (FM), or LOCALOFF (MW/LW) appears. The broadcast signal is too weak. t Perform manual tuning.
There may be an internal malfunction. t Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer.
The unit cannot be operated because of some problem. t Press the RESET button (page 4). If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began.

Unlock Desbloqueo Ls upp Destranque

Tab Lengeta Flik Patilha

10 discs, one in each tray 10 discos, uno en cada bandeja 10 CD-skivor, med en CD-skiva i varje skivfack 10 discos, um em cada tabuleiro
Anvnd medfljande skivmagasin eller skivmagasinet XA-250. Skivmagasinet XA-10B kan anvndas med denna enhet. Anvnd inget annat magasin, eftersom det kan orsaka fel. Utilize o carregador de discos fornecido ou o carregador XA-250. No pode utilizar o carregador de discos XA-10B com este aparelho. Se utilizar outro carregador qualquer pode provocar uma avaria.
Use the supplied disc magazine or the disc magazine XA-250. The disc magazine XA-10B can not be used with this unit. If you use any other magazine, it may cause a malfunction. Emplee el cargador de discos suministrado o el XA-250. El cargador de discos XA-10B no puede utilizarse con esta unidad. Si emplea otro tipo de cargador, puede producir fallos de funcionamiento.
Release, and slide open. Suelte y deslice para abrir. Lossa och skjut t sidan. Solte e abra.
Disc magazine Cargador de discos Skivmagasin Carregador de discos
To remove Extraccin Urtagning Para retirar
If the disc magazine does not lock properly Take out the magazine, and after pressing the EJECT button, reinsert it. Si el cargador de discos no encaja adecuadamente. Extraiga el cargador y, despus de presionar el botn EJECT, vuelva a insertarlo. Nr skivmagasinet inte kommer p plats ordentligt Ta ut skivmagasinet. Tryck drefter p EJECT och stt i det igen. Se o carregador de discos no fechar bem Retire o carregador, carregue na tecla EJECT e volte a introduzi-lo. EJECT
Use the unit with the door closed Otherwise, foreign matter may enter the unit and contaminate the lenses inside the changer. Emplee la unidad con la puerta cerrada. De lo contrario podran entrar objetos extraos y contaminar las lentes del interior del cambiador. Kom ihg att stnga locket till skivmagasinsfacket Fr att frhindra frmmande freml frn att trnga in i CD-vxlare och smutsa ned de inbyggda linserna. Utilize o aparelho com a porta fechada Caso contrrio, objectos estranhos podero penetrar no aparelho e sujar as lentes no interior do permutador.
Notes on the disc magazine
Do not leave the disc magazine in locations with high temperatures and high humidity such as on a car dashboard or in the rear window where the disc magazine will be subjected to direct sunlight. Do not place more than one disc at a time onto one tray, otherwise the changer and the discs may be damaged. Do not drop the disc magazine or subject it to a violent shock.

Before playing, clean the discs with an optional cleaning cloth. Wipe each disc in the direction of the arrows. Do not use solvents such as benzine, thinner, commercially available cleaners or antistatic spray intended for analog discs.
No exponga los discos a la luz solar directa ni a fuentes trmicas, como conductos de aire caliente. No deje los discos en un automvil aparcado bajo la luz solar directa donde pueda producirse un considerable aumento de temperatura en el interior de dicho automvil.
Utstt inte CD-skivor fr direkt solljus eller vrmekllor som varluftsventiler. Lmna inte CDskivor i bilen om den str parkerad i direkt solljus, eftersom kraftiga temperaturstegringarr skadligt fr skivorna.
No exponha os discos luz solar directa ou a fontes de calor como condutas de ar quente. No deixe os discos dentro de um automvel estacionado ao sol pois pode ocorrer um aumento considervel de temperatura no seu interior.
Antes de reproducir un disco, lmpielo con un pao limpiador opcional. Hgalo en el sentido de las flechas. No emplee disolventes tales como bencina, diluyente de pintura, ni limpiadores o aerosoles destinados a discos analgicos.
Torka CD-skivan med en rengringsduk (medfljer inte) innan du spelar den. Torka frn mitten ut mot kanten (i pilarnas riktning). Anvnd inte lsningsmedel som bensin och thinner, eller rengringsmedel och antistatspray avsedda fr vinylskivor.
Antes de iniciar a reproduo, limpe os discos com um pano de limpeza (venda avulsa). Limpe o disco no sentido indicado pelas setas. No utilize solventes tais como benzina, diluentes, produtos de limpeza disponveis no mercado ou aerosis anti-estticos destinados a discos de gravao analgica.

Installation

Choose the mounting location carefully, observing the following: The unit is not subject to temperatures exceeding 55C (such as in a car parked in direct sunlight). The unit is not subject to direct sunlight. The unit is not near heat sources (such as heaters). The unit is not exposed to rain or moisture. The unit is not exposed to excessive dust or dirt. The unit is not subject to excessive vibration. The fuel tank should not be damaged by the tapping screws. There should be no wire harnesses or pipes under the place where you are going to install the unit. The spare tire, tools or other equipment in or under the trunk should not be interfered with or damaged by the screws or the unit itself. Be sure to use only the supplied mounting hardware for a safe and secure installation. Use only the supplied screws. Make holes of 3.5 mm only after making sure there is nothing on the other side the mounting surface.