English

Playing a tape
Use TYPE I (normal) tape only.

Recording

Falling asleep to music

Precautions

On safety
As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further.

On operation

If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. If the player has not been used for a long time, set it in the playback mode to warm it up for a few minutes before inserting a cassette.
If you have any questions or problems concerning your player, please consult your nearest Sony dealer.

Troubleshooting

General The power does not come on. Make sure the batteries are inserted correctly. Replace all the batteries with new ones if they are weak. You cannot turn on the player with the remote when you operate the player on batteries (CFD-S36 only). The power is not on, and "bAttErY" and "Error" are displayed alternately. Make sure the batteries are inserted correctly. Replace all the batteries with new ones if they are weak. There is no audio. Unplug the headphones when listening through speakers. Noise is heard. Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. CD Player The CD does not play or no dISC lights in the display even when a CD is in place. Place the CD with the label surface up. Clean the CD. Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. The CD-R/CD-RW was not finalized. Finalize the CD-R/CDRW with the recording device. There is a problem with the quality of the CD-R/CD-RW, recording device, or application software. The sound drops out. Reduce the volume. Clean the CD, or replace it if the CD is badly damaged. Place the player in a location free from vibration. Clean the lens with a commercially available blower. The sound may drop out or noise may be heard when using poor quality CD-Rs/CD-RWs or if there is a problem with the recording device or application software. Radio The audio is weak or has poor quality. Replace all the batteries with new ones if they are weak. Move the player away from the TV. The picture of your TV becomes unstable. If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV.
Tape Player The tape does not move when you press an operation button. Close the cassette compartment securely. The REC z button does not function or the tape does not play or record. Make sure the safety tab on the cassette is in place. Poor or distorted playback, recording or erasing quality. Clean the heads, pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol. Replace all the batteries with new ones if they are weak. TYPE II (high position) or TYPE IV (metal) tape is being used. Use TYPE I (normal) tape only. Demagnetize the heads using a commercially available tape head demagnetizer. Record/playback head Capstan

Specifications

AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 3.2-ohm loads, both channels driven from 150 - 6,300 Hz; rated 1.8 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation.

Supplied accessory AC power cord (1) Remote control (1) (CFD-S36 only) Design and specifications are subject to change without notice.

WARNING

To prevent fire or shock hazard, do not expose the player to rain or moisture.

Information

For customers in the United States
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have any questions about this product, you may call: Sony Direct Response Center 1-(800)-222-7669 or write to: Sony Direct Response Center 12451 Gateway Blvd. Fort Myers, FL 33913
Press TAPE (direct power-on).

Display

Press xZ to open the tape compartment and insert a blank tape.
With the side you want to record on facing upward

STOP/EJECT

For CFD-S36 USA model only
Play the music source you want.

Optional accessories

Sony MDR headphone series
Declaration of Conformity
Trade Name: Model: Responsible Party: SONY CFD-S36 Sony Electronics Inc. Address: 1 Sony Drive, Park Ridge, NJ 07656 U.S.A. Telephone Number: 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Press SLEEP to display SLEEP.
Press xZ to open the tape compartment and insert a recorded tape. Close the compartment.
With the side you want to play facing upward

Other Specifications

CD player section
System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 W (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20,000 Hz +1/2 dB Wow and flutter Below measurable limit

CD Radio CassetteCorder

Operating Instructions
This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Cleaning the cabinet

Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine.
Select the program source you want to record. To record from the CD player Press CD and insert a CD (See "Playing a CD").
Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: 60 t 90 t 120 t no indication t 10 t 20 t 30.

On power sources

For AC operation, use the supplied AC power cord; do not use any other type. The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. Unplug the player from the wall outlet when it is not to be used for an extended period of time. For battery operation, use six size D (R20) batteries. When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. The nameplate indicating operating voltage, power consumption, etc. is located at the bottom.

Owner's Record

The model number is located at the bottom and the serial number is located in the battery compartment. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.
Radio section Erase head Pinch roller Lens
Frequency range FM: 87.6 - 108 MHz AM: 530 - 1,710 kHz TV: 2 - 13 CH (CFD-S36 USA model only) WEATHER: 1 - 7 CH (CFD-S36 USA model only) Antennas FM/TV/WEATHER: Telescopic antenna AM: Built-in ferrite bar antenna

Press N.

CFD-S26 CFD-S36
Sony Corporation 2000 Printed in China

CAUTION

The use of optical instruments with this product will increase eye hazard.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
To record from the radio Press RADIO BANDAUTO PRESET and tune in the station you want (See "Listening to the radio").

RADIO BAND

AUTO PRESET
To cancel the sleep function
Press POWER to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end.

About this manual

The instructions in this manual are for the CFD-S26 and CFD-S36. Before you start reading, check your model number. The CFD-S36 is the model used for illustration purpose.

3-227-155-14(1)

For customers in Canada
To prevent electric shock, match wide blade of plug to wide slot, fully insert.

Cassette-corder section

Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10,000 Hz
To adjust the volume stop playback fast-forward or rewind the tape pause playback
Press VOLUME +, (VOL +, on the remote, CFD-S36 only) xZ M or m X Press the button again to resume play after pause. xZ POWER

Choosing Power Sources

Connecting the AC power cord
Insert one end of the supplied AC power cord to the AC IN socket located at the rear of the player, and the other end to the wall outlet.

On placement

Remote (CFD-S36 only) The remote does not function. Replace all the batteries in the remote with new ones if they are weak. Make sure that you are pointing the remote at the remote sensor on the player. Remove any obstacles in the path of the remote and the player. Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. Move closer to the player when using the remote.
After trying the above remedies, if you still have problems, unplug the AC power cord and remove all the batteries. After all the indications in the display disappear, plug the power cord and insert the batteries again. If the problem persists, please consult your nearest Sony dealer.
Press z to start recording. (N is depressed automatically).
eject the cassette turn on/off the player

Notes on cassettes

Break off the cassette tab from side A or B to prevent accidental recording. If you want to reuse the tape for recording, cover the broken tab with adhesive tape. Side A To stop recording pause recording turn on/off the player Tab for side B Tab for side A Tips Adjusting the volume or the audio emphasis will not affect the recording level. For the best results, use the AC power as a power source for recording. To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z. Press xZ X Press the button again to resume recording. POWER

Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. Do not place the player on an inclined or unstable place. Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet.

General

Speaker Full range: 10 cm dia., 3.2 ohms, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 ohms impedance headphones Power output (excluding USA model) 2.3 W + 2.3 W (at 3.2 ohms, 10 % harmonic distortion in AC operation) Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz 9 V DC, 6 size D (R20) batteries For remote control (CFD-S36 only): 3 V DC, 2 size AA (R6) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h Tape playback Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h CD playback Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h Dimensions Approx. 284 mm (w/h/d) (inches) (incl. projecting parts) Mass Approx. 3.8 kg (8 lb. 6 oz) (incl. batteries)
Inserting batteries into the remote (CFD-S36 only)
Insert two size AA (R6) batteries (not supplied)

to AC IN

Replacing batteries
With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace all the batteries with new ones. Note When you operate the player on batteries, you cannot turn on the player using the remote.

to a wall outlet

The use of a cassette with more than 90 minutes of play time is not recommended except for long, continuous recording or playback.
Using the player on batteries
Insert six size D (R20) batteries (not supplied) into the battery compartment. Notes Replace the batteries when the OPR/BATT indicator dims or when the player stops operating. Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player. To use the player on batteries, disconnect the AC power cord from the player.

Location of controls

REC PLAY REW FF STOP/EJECT PAUSE

Playing a CD

Listening to the radio

Using the display

Checking the total track number and playing time
Press DISPLAY ENTMEMORY in stop mode.
VOLUME +, BX Number buttons for CD/RADIO DIRECT OPERATION SLEEP POWER Tape compartment Z PUSH OPEN/CLOSE CD compartment MEGA Xpand (CFD-S36 only) MEGA BASS x
Press CD (direct power-on).

Shuffle Play

About CD-Rs/CD-RWs
This player is compatible with CD-Rs/CD-RWs but playback capability may vary depending on the quality of the disc, the recording device and application software.
If a station cannot be preset automatically
Press CD. Press MODE until SHUF appears in the display. Press u to start shuffle play.
Remote Control (CFD-S36 only)
Total track number Total playing time

Notes on CDs

Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out.
Press RADIO BANDAUTO PRESET until the band you want appears in the display (direct power-on). Each time you press the button, the indication changes as follows: CFD-S36 USA model: FM t AM t TV. Other models: FM t AM.
You need to preset a station with a weak signal manually.
1 Press RADIO BANDAUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station
on for about 2 seconds. To select the preset number over 10, press >10 first, then the corresponding number buttons. You need to hold down the last number button to enter for about 2 seconds. (Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.) Display
CD/RADIO DIRECT OPERATION
FUNCTION Number buttons MODE TUNE +, BAND WEATHER (USA model only) N

FUNCTION SLEEP

>10 VOL

CD/RADIO (AC ONLY)

Press Z PUSH OPEN/CLOSE down to open the CD compartment and place a CD in the CD compartment.
Checking the remaining time
Press DISPLAY ENTMEMORY while playing a CD. To display the current track number and the remaining time on the current track* the number of tracks left and remaining time on the CD Press DISPLAY ENTMEMORY once twice

To cancel Shuffle Play

Press MODE until SHUF disappears from the display.

Program Play

VOL +, x X

PUSH OPEN/CLOSE

WEATHER TUNE

With the labeled side up

Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. Do not stick paper or sticker on the CD, nor scratch the surface of the CD. After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error.
Press CD. Press MODE until PGM appears in the display. Press the number buttons for the tracks you want to program in the order you want. You can arrange the playing order of up to 20 tracks on a CD.
Hold down TUNE + or until the frequency digits begin to change in the display.

>10

MEGA Xpand

MEGA BASS

MEGA Xpand TAPE TUNE ,+.,> DISPLAY ENT MEMORY i (headphones) jack MODE OPR/BATT indicator RADIO BAND AUTO PRESET CD

.,> MEGA BASS

three times the current track number and playing time * For a track whose number is more than 20, the remaining time appears as - -:- - in the display.
WEATHER Display (CFD-S36 USA model only) Remote sensor (CFD-S36 only)
Locating a specific track
Close the CD compartment.
To locate a specific track directly
The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step.
The new station replaces the old one.
Press a number button of the track. > (forward) or. (backward) while playing until you find the point. > (forward) or. (backward) in pause until you find the point.
Programmed track Playing order To adjust the volume Press VOLUME +, (VOL +, on the remote, CFD-S36 only) POWER
a point while listening to the sound a point while observing the display
Playing preset radio stations
Press u to start program play.
Press RADIO BANDAUTO PRESET to select the band. Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then corresponding number buttons. (Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)

turn on/off the radio

To cancel Program Play
Press MODE until PGM disappears from the display.
Tip To listen through headphones, connect the headphones to the i (headphones) jack.
To improve broadcast reception
Reorient the antenna for FM/TV/WEATHER. Reorient the player itself for AM.
Press u (N on the remote, CFD-S36 only). The player plays all the tracks once.
Tip When you locate a track numbered over 10, press >10 first, then the corresponding number buttons. Example:To play track number 23, press >10 first, then 2 and 3. Note You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by pressing x.
To check the order of tracks before play
Press DISPLAY ENTMEMORY. Every time you press the button, the track number appears in the programed order.
Adjusting the sound emphasis (MEGA BASS/MEGA Xpand)
Reinforcing the bass sound
Press MEGA BASS. "MEGA BASS" appears in the display. To return to normal sound, press the button again.
To change the current program
Press x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programming procedure. Tip You can record your own program. After youve created the program, insert a blank tape and press z to start recording. FM/TV/WEATHER Tip
If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in monaural.

Track number

Playing time

Repeat Play

To adjust the volume stop playback pause playback Press VOLUME +, (VOL +, on the remote, CFD-S36 only) x u (X on the remote, CFD-S36 only) Press the button again to resume play after pause. >. Z PUSH OPEN/CLOSE POWER
Press CD. Proceed as follows:
To repeat a single track Do this 1 Press MODE until REP 1 appears. 2 Press the number button for the track you want to repeat. 1 Press MODE until REP ALL appears. 2 Press u. 1 Press MODE until SHUF REP appears. 2 Press u. 1 Press MODE until PGM REP appears. 2 Press the number buttons for the tracks you want to program in the order you want up to 20 tracks. 3 Press u.
Checking the weather forecast (CFD-S36 USA model only)
Getting the MEGA Xpand effect (CFD-S36 only)
Press MEGA Xpand. "MEGA Xpand" appears in the display. You can get the effect of expansion of the sound field.
Presetting radio stations

You can store radio stations into the players memory. You can preset up to 40 radio stations (CFD-S36 USA model), 20 for FM and 10 for AM and TV in any order, or 30 radio stations (other models), 20 for FM and 10 for AM in any order.
Press WEATHER. The power turns on automatically.

WEATHER

all the tracks tracks in random order programmed tracks
Hold down TUNE + or - until the channel indication begins to change in the display. The player automatically scans the weather forecast stations and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step.
Press RADIO BANDAUTO PRESET to select the band. Hold down RADIO BANDAUTO PRESET for 2 seconds until "AUTO" flashes in the display.
go to the next track go back to the previous track remove the CD turn on/off the player

To cancel Repeat Play

Press MODE until REP disappears from the display.
Press DISPLAY ENTMEMORY. The stations are stored in memory from the lower frequencies to the higher ones.
Tip Weather band provides continuous broadcast of the latest weather information (directly from National Weather Service offices).