[ Cleaning

Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the set.
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power-line surges.

Service Installation

[ Water and Moisture
Do not use power-line operated sets near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
[ Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled or objects have fallen into the set. If the set has been exposed to rain or water. If the set has been subject to excessive shock by being dropped, or the cabinet has been damaged. If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the set to normal operation. When the set exhibits a distinct change in performance this indicates a need for service.

[ Power-Cord Protection

Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against them, paying particular attention to the plugs, receptacles, and the point where the cord exits from the appliance.

[ Accessories

Do not place the set on an unstable cart, stand, tripod, bracket, or table. The set may fall, causing serious injury to a child or an adult, and serious damage to the set. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer.

[ Ventilation

The slots and openings in the cabinet are provided for necessary ventilation. To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered. Never cover the slots and openings with a cloth or other materials. Never block the slots and openings by placing the set on a bed, sofa, rug, or other similar surface. Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided. Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight.

[ Servicing

Do not attempt to service the set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

[ Replacement parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.

[ Safety Check

Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition.

[ Lightning

For added protection for this set during a lightning storm, or when it is left unattended and unused for
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\020REG.fm master:Left

Read this first CAUTION

Replace the battery with the specified type only. Otherwise, fire or injury may result.
If you have any questions about this product, you may call: Sony Customer Information Center 1-800-222-SONY (7669) The number below is for the FCC related matters only.
For Customers in the U.S.A. and Canada
[ RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/ Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Regulatory Information

Declaration of Conformity Trade Name: SONY Model No.: DSC-W200 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127U.S.A. Telephone No.: 858-942-2230 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Battery charger

This power unit is intended to be correctly orientated in a vertical or floor mount position.

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The supplied interface cable must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

For Customers in Europe

This product has been tested and found compliant with the limits set out in the EMC Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the communication cable (USB, etc.) again.
[ Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)
For the State of California, USA only
Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate.
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Notice for customers in the United Kingdom
A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\010COVTOC.fm master:Right

Table of contents

IMPORTANT SAFEGUARDS... 2 Read this first.... 4 Notes on using your camera... 8

Getting started... 9

Checking the accessories supplied.. Preparing the battery pack... Inserting the battery pack/a Memory Stick Duo (not supplied). Turning the camera on/setting the clock.. 13
Shooting images easily... 14
Mode dial/Zoom/Flash/Macro/Self-timer/Display.. 15
Viewing/deleting images... 17 Learning the various functions HOME/Menu.. 19
Using the HOME screen... 19 HOME items... 20 Using menu items... 21 Menu items... 22
Enjoying your computer... 23
Supported Operating Systems for USB connection and application software (supplied)... 23 Viewing Cyber-shot Handbook and Cyber-shot Step-up Guide. 24
Indicators on the screen... 25 Battery life and memory capacity.. 27
Battery life and number of images that can be recorded/viewed.. 27 Number of still images and recording time of movies.. 28

Troubleshooting... 29

Battery pack and power... 29 Shooting still images/movies... 30 Viewing images... 30
Precautions... 31 Specifications... 32
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\030NOT.fm master:Left
Notes on using your camera
[ Internal memory and Memory Stick Duo back up
Do not turn off the camera or remove the battery pack or Memory Stick Duo while the access lamp is lighted, as the internal memory data or Memory Stick Duo data may be destroyed. Always protect your data by making a back up copy.
[ Notes on the LCD screen and lens
The LCD screen is manufactured using extremely high-precision technology so over 99.99% of the pixels are operational for effective use. However, there may be some tiny black points and/or bright points (white, red, blue or green in color) that constantly appear on the LCD screen. These points are normal in the manufacturing process and do not affect the recording in any way. When the battery level becomes low, the lens might stop moving. Insert a charged battery pack and turn on the camera again.

[ Notes on recording/playback
Before you start recording, make a trial recording to make sure that the camera is working correctly. This camera is neither dust-proof, nor splashproof, nor water-proof. Read Precautions (page 31) before operating the camera. Be careful not to get the camera wet. Water entering the inside of the camera may cause malfunctions which in some cases may not be repairable. Do not aim the camera at the sun or other bright light. It may cause the malfunction of your camera. Do not use the camera near a location that generates strong radio waves or emits radiation. The camera may not be able to record or play back properly. Using the camera in sandy or dusty locations may cause malfunctions. If moisture condensation occurs, remove it before using the camera (page 31). Do not shake or strike the camera. In addition to malfunctions and an inability to record images, this may render the recording medium unusable, or cause image data breakdown, damage or loss. Clean the flash surface before use. The heat of flash emission may cause dirt on the flash surface to become discolored or to stick to the flash surface, resulting in insufficient light emission.
[ On image data compatibility
This camera conforms with DCF (Design rule for Camera File system) universal standard established by JEITA (Japan Electronics and Information Technology Industries Association). Playback of images recorded with your camera on other equipment and playback of images recorded or edited with other equipment on your camera are not guaranteed.

[ Warning on copyright

Television programs, films, videotapes, and other materials may be copyrighted. Unauthorized recording of such materials may be contrary to the provisions of the copyright laws.
[ No compensation for contents of the recording
The contents of the recording cannot be compensated for if recording or playback is not possible due to a malfunction of your camera or recording media, etc.
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\040PRE.fm master:Right

Getting started

Checking the accessories supplied
Battery charger BC-CSG/BC-CSGB/ BC-CSGC (1) USB, A/V cable for multi-use terminal (1)
Wrist strap (1) Power cord (mains lead) (1) (not supplied in the USA and Canada) CD-ROM (Cyber-shot application software/ Cyber-shot Handbook/Cyber-shot Step-up Guide) (1) Instruction Manual (this manual) (1) Rechargeable battery pack NP-BG1 (1)/ Battery case (1)
Attach the strap and place your hand through the loop to prevent the camera from damage by being dropped, etc.
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\040PRE.fm master:Left_PrepL2
1 Preparing the battery pack
For customers in the USA and Canada Plug
For customers other than those in the USA and Canada
CHARGE lamp CHARGE lamp Power cord (mains lead)
1 Insert the battery pack into the battery charger. 2 Connect the battery charger to the wall outlet (wall socket).
The CHARGE lamp lights on, and charging starts. When the CHARGE lamp turns off, charging is finished (Practical charge). If you continue charging the battery pack for about one more hour (until it is fully charged), the charge will last slightly longer.

[ Charging time

Full charge time Practical charge time

Approx. 330 min.

Approx. 270 min.
Time required to charge a fully depleted battery pack at a temperature of 25C (77F). Charging may take longer under certain circumstances or conditions. See page 27 for the number of images that can be recorded. Connect the battery charger to an easily accessible wall outlet (wall socket) close by. Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket). When charging is finished, disconnect the power cord (mains lead) from the wall outlet (wall socket), and remove the battery pack from the battery charger. Designed for use with compatible Sony batteries.
2 Inserting the battery pack/a Memory Stick Duo (not supplied)
Insert the Memory Stick Duo with the terminal side facing the LCD screen. Battery/Memory Stick Duo cover
Insert the battery pack while pressing the battery eject lever with the tip of the battery pack.
1 Open the battery/Memory Stick Duo cover. 2 Insert the Memory Stick Duo (not supplied) all the way in until it clicks. 3 Insert the battery pack. 4 Close the battery/Memory Stick Duo cover.

The z (AE/AF lock) indicator (green) flashes, a beep sounds, the indicator stops flashing and remains lit.
2 Press the shutter button fully down.

AE/AF lock indicator

When shooting movies: Press the shutter button fully down. To stop recording, press the shutter button fully down again.
Mode dial/Zoom/Flash/Macro/Self-timer/Display

[ Using the mode dial

Set the mode dial to the desired function.

Auto Adjustment

Allows easy shooting with the settings adjusted automatically.
* Scene Selection in the menu

Extra High Sensitivity

Shoots smoother images without a flash under low light conditions.
Shoots seaside or lakeside scenes with the blueness of the water captured more vividly.

Program Auto

Allows you to shoot with the exposure adjusted automatically (both the shutter speed and the aperture value). Also you can select various setting using the menu.
Shoots snow scenes in white more clearly.
M Manual Exposure shooting
Allows you to shoot after adjusting the exposure manually.

Fireworks

Shoots fireworks in all their splendor.

Movie mode

Allows you to record movies with audio.

[ W/T Using the zoom

Press T to zoom, press W to undo zoom.

High Sensitivity

Shoots images without a flash even in low lighting.
Flash (Selecting a flash mode for still images)

Soft Snap

Shoots images with a softer atmosphere for portraits of people, flowers, etc.
Press B ( ) on the control button repeatedly until the desired mode is selected.
: Flash Auto Strobes when there is insufficient light or backlight (default setting) : Flash forced on : Slow synchro (Flash forced on) The shutter speed is slow in a dark place to clearly shoot the background that is out of flash light. : Flash forced off

Twilight Portrait

Shoots sharp images of people in a dark place without losing the nighttime atmosphere.

[ To delete images in index mode
1 Press MENU while the index screen is displayed. 2 Select [Delete] with v and select [Multiple Images] with b/B, then press z. 3 Select the image you want to delete with v/V/b/B, then press z.
mark is checked in the checkbox of the image. To cancel a selection, select an image you have selected for deletion, then press z again.
4 Press MENU and select [OK] with v, then press z.
To delete all the images in a folder, select [All In This Folder], then press z in step 2.
[ To play back a series of images (Slide Show)
1 Select [ Slide Show] in (View Images) on the HOME screen. 2 Select [Start] with v, then press z.
[ To view images on TV screen
Connect the camera to the TV with the cable for multi-use terminal (supplied).

To the multi connector

To audio/video input jacks
Cable for multi-use terminal
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\050MEN.fm master:Right
Learning the various functions HOME/Menu

Using the HOME screen

The HOME screen is the gateway screen for all the functions of your camera. You can select the shooting mode or playback mode, or change the settings from the HOME screen.

HOME button

z button
1 Press HOME to display the HOME screen.

Category Item

Select a category with b/B on the control button. Select an item with v/V, then press z.

[ When you select the

(Manage Memory) or

(Settings) category

1 Select the desired item with v/V on the control button.
This is functional only when you select (Settings).
2 Move to the right with B, select a setting with v/V, then press z. 3 Select a setting with v/V, then press z.
The camera is set to the shooting mode by pressing the shutter button halfway down.
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\050MEN.fm master:Left
For details on the operation 1 page 19

HOME items

Press HOME button displays the following items. Details on the items are displayed on the screen by the guide.

Category Items

Shooting Single Image Index Display Slide Show

Shooting View Images

Printing, Other
Print Music Tool Download Music Format Music

Manage Memory

Memory Tool Memory Stick Tool Format Change REC. Folder Internal Memory Tool Format Create REC. Folder Copy

Settings

Main Settings Main Settings 1 Beep Initialize Main Settings 2 USB Connect Video Out Shooting Settings Shooting Settings 1 AF Illuminator AF Mode Conversion Lens Shooting Settings 2 Auto Orientation Clock Settings Language Setting Grid Line Digital Zoom Function Guide

Supported Operating Systems for USB connection and application software (supplied)
For Windows users USB connection Application software Picture Motion Browser For Macintosh users
Windows 2000 Professional, Windows XP*, Windows Vista* Windows 2000 Professional, Windows XP*, Windows Vista*
Mac OS 9.1/9.2/ Mac OS X(v10.1 to v10.4) not compatible
* 64-bit editions and Starter (Edition) are not supported. Must be installed with above OS at delivery. If your OS does not support USB connections, use a commercially available Memory Stick Reader/Writer. For further details on the operating environment of Picture Motion Browser Cyber-shot application software, refer to Cyber-shot Handbook.
D:\#SAGYO\sony\070322_1_841408S\3208406611\3208406611DSCW200U2\01GBDSCW200U2\060PC.fm master:Left
Viewing Cyber-shot Handbook and Cyber-shot Step-up Guide
[ For Windows users [ For Macintosh users
Turn on your computer, and insert the CDROM (supplied) into the CD-ROM drive. Follow the instructions below.
1 Turn on your computer, and insert the CDROM (supplied) into the CD-ROM drive.
The screen below appears.
To view the Cyber-shot Handbook
1 Select the [Handbook] folder and copy
Handbook.pdf stored in the [GB] folder to your computer.
2 After copying is complete, double-click

Handbook.pdf.

When you click the [Cyber-shot Handbook] button, the screen for copying Cyber-shot Handbook appears.
To view the Cyber-shot Step-up Guide
2 Follow the on-screen instructions to copy.
When you click the Cyber-shot Handbook button, the both of the Cyber-shot Handbook and the Cyber-shot Step-up Guide will be installed.
1 Copy the [stepupguide] folder in the
[stepupguide] folder to your computer.
2 Select [stepupguide], [language] and then
[GB] folder stored in the CD-ROM and copy all the files in the [GB] folder, then write over them to the files in the [img] folder stored in [stepupguide] which is copied to your computer in the step 1.
3 After the installation is complete, doubleclick the shortcut created on the desktop.
3 After copying is completed, double-click
stepupguide.hqx in the [stepupguide] folder to uncompress it, then double-click the generated file stepupguide.
If an uncompress tool for HQX file is not installed, install the Stuffit Expander.

[ When viewing still images
No. of Images Battery life (min.)

Approx. 6200

Approx. 310
Viewing single images in order at about three second intervals
LCD screen ON (min.) LCD screen OFF (min.)

Approx. 120

Approx. 140
Shooting movies continuously with an image size of [320]
LCD screen No. of Images Battery life (min.)

On Off

Approx. 300 Approx. 350

Approx. 150 Approx. 175

Shooting in the following situations: [AF Mode] is set to [Single]. [SteadyShot] is set to [Shooting]. Shooting once every 30 seconds. The zoom is switched alternately between the W and T ends. The flash strobes once every two times. The power turns on and off once every ten times.
Number of still images and recording time of movies
The number of still images and the length of time for movies may vary depending on the shooting conditions.
You can select the image size to be used when shooting from the menu (pages 21, 22).
[ The approximate number of still images

(Units: Images)

Capacity Size Internal memory Approx. 31 MB 128 MB Memory Stick Duo formatted with this camera 256 MB 512 MB 1 GB 2 GB 4 GB 8 GB
12M 3:2 8M 5M 3M VGA 16:9
The number of images listed is for when [REC Mode] is set to [Normal]. When the number of remaining shootable images is greater than 9,999, the >9999 indicator appears. When images recorded using earlier Sony models are played back on this camera, the display may differ from the actual image size.
[ The approximate recording time of movies
(Units: hour : minute : second)
640(Fine) 640(Standard) 320

0:01:30 0:06:00

0:05:50 0:23:40

0:02:50 0:10:40 0:42:50

0:06:00 0:21:40 1:27:00

0:12:20 0:44:20 2:57:50

0:25:10 1:31:00 6:04:30

0:50:00 3:00:00

1:40:20 6:01:10

12:00:20 24:04:50

Movies with the size set to [640(Fine)] can only be recorded on a Memory Stick PRO Duo. The size of a movie file is limited to approx. 2 GB. During recording, movie recording stops automatically when the file size of the movie reaches approx. 2 GB. This camera does not support HD recordings or playbacks for movies.

Troubleshooting

If you experience trouble with your camera, try the following solutions.
1 Check the items below, and refer to Cyber-shot Handbook (PDF).
If a code such as C/E:ss:ss appears on the screen, refer to Cyber-shot Handbook.
2 Remove the battery pack, and insert the battery pack again after about one minute, and turn on the power.
3 Initialize the settings (page 20).
4 Consult your Sony dealer or local authorized Sony service facility.
Please understand that you give your consent that the contents of the internal memory, Music files may be checked when you send your camera to be repaired.

Battery pack and power

The battery pack cannot be inserted.
Insert the battery pack correctly to push the battery eject lever (page 11).
Cannot turn on the camera.
After installing the battery pack into the camera, it may take a little while to get the camera

powered.

Insert the battery pack correctly (page 11). The battery pack is discharged. Insert charged battery pack (page 10). The battery pack is dead. Replace it with a new one. Use a recommended battery pack (page 9).
The power turns off suddenly.
If you do not operate the camera for about three minutes while the power is on, the camera
turns off automatically to prevent wearing down the battery pack. Turn on the camera again (page 13). The battery pack is dead. Replace it with a new one.
The battery remaining indicator is incorrect.
This phenomenon occurs when you use the camera in an extremely hot or cold location. The displayed battery remaining differs from the current one. Fully discharge and then charge
the battery pack to correct the display.
The battery pack is discharged. Insert the charged battery pack (page 10). The battery pack is dead. Replace it with a new one.
Cannot charge the battery pack.
You cannot charge the battery pack using the AC Adaptor (not supplied).
Shooting still images/movies
Your camera cannot record images.
Check the free capacity of the internal memory or Memory Stick Duo (page 28). If it is full,
do one of the following: Delete unnecessary images (page 17). Change the Memory Stick Duo. You are using the Memory Stick Duo with the write-protect switch, and the switch is set to the LOCK position. Set the switch to the recording position. You cannot record images while charging the flash. When shooting a still image, set the mode dial to a position other than. Set the mode dial to when shooting movies. The image size is set to [640(Fine)] when recording movies. Do one of the following: Set the image size to other than [640(Fine)]. Insert a Memory Stick PRO Duo.
Cannot insert dates on images.
This camera does not have a feature for superimposing dates on images. By using Picture
Motion Browser, you can print or save images with the date.

[ On cleaning

Cleaning the LCD screen Wipe the screen surface with an LCD cleaning kit (not supplied) to remove fingerprints, dust, etc. Cleaning the lens Wipe the lens with a soft cloth to remove fingerprints, dust, etc. Cleaning the camera surface Clean the camera surface with a soft cloth slightly moistened with water, then wipe the surface with a dry cloth. Do not use the following as they may damage the finish or the casing. Chemical products such as thinner, benzine, alcohol, disposable cloths, insect repellent, sunscreen or insecticide, etc. Do not touch the camera with the above on your hand. Do not leave the camera in contact with rubber or vinyl for a long time.

Specifications

Camera

[System]

Image device: 9.29 mm (1/1.72 type) color CCD, Primary color filter Total pixel number of camera: Approx. 000 pixels Effective pixel number of camera: Approx. 000 pixels Lens: Carl Zeiss Vario-Tessar 3 zoom lens f = 7.6 22.8 mm (mm when converted to a 35 mm still camera) F2.8 5.5 Exposure control: Automatic exposure, Scene Selection (9 modes) White balance: Automatic, Daylight, Cloudy, Fluorescent 1,2,3, Incandescent, Flash File format (DCF compliant): Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media: Internal Memory (approx. 31 MB), Memory Stick Duo Flash:Flash range (ISO sensitivity (Recommended exposure Index) set to Auto): approx. 0.2 to 3.3 m (7 7/8 inches to 10 feet 10 inches) (W)/approx. 0.4 to 1.8 m (1 feet 3 3/4 inches to 5 feet 10 7/8 inches) (T)

[Power, general]

Power: Rechargeable battery pack NP-BG1, 3.6 V AC-LS5K AC Adaptor (not supplied), 4.2 V Power consumption (during shooting with the LCD screen on): 1.3 W Operating temperature: 0 to 40C (32 to 104F) Storage temperature: 20 to +60C (4 to +140F) Dimensions: 91.0 58.5 27.3 mm (3 5/3/1/8 inches) (W/H/D, excluding protrusions) Mass: Approx. 173 g (6.1 oz) (including NP-BG1 battery pack and strap, etc.) Microphone: Monaural Speaker: Monaural Exif Print: Compatible PRINT Image Matching III: Compatible PictBridge: Compatible
BC-CSG/BC-CSGB/BC-CSGC battery charger
Power requirements: AC 100 V to 240 V, 50/ 60 Hz, 2 W (BC-CSG/BC-CSGC)/ 2.6 W (BC-CSGB) Output voltage: DC 4.2 V, 0.25 A Operating temperature: 0 to 40C (32 to 104F) Storage temperature: -20 to +60C (4 to +140F) Dimensions: Approx. 91 mm (2 1/2 31/5/8 inches) (W/H/D) Mass: Approx. 75 g (2.7 oz)
[Input and Output connectors]
Multi connector: Video output Audio output (Monaural) USB communication USB communication: Hi-Speed USB (USB 2.0 compliant)

[LCD screen]

LCD panel: 6.2 cm (2.5 type) TFT drive Total number of dots: (480 240) dots

REC Mode: Selecting the continuous shooting method
Selects whether the camera performs continuous shooting or not when you press the shutter button.

(Normal) (Burst)

Does not shoot continuously. Records up to 100 images in succession when you press and hold down the shutter button.

The flash is set to

(Flash forced off).
BRK 0.3EV BRK 0.7EV BRK 1.0EV
Records a series of three images with the exposure values automatically shifted (Exposure Bracket). The larger the bracket step value, the larger the shift of the exposure value.
When you cannot decide the correct exposure, shoot in the Exposure Bracket mode, shifting the exposure value. You can select the image with the best exposure afterward.
When the mode dial is set to , the Exposure Bracket mode is not available. The flash is set to (Flash forced off).

On the Burst

When recording with the self timer, a series of a maximum of five images is recorded. The recording interval is approximately 0.46 seconds (DSC-W90) or 0.36 seconds (DSC-W80/W85). The recording interval becomes longer, depending on the setting for the image size. When the battery level is low, or when the internal memory or Memory Stick Duo is full, the Burst stops. You may not be able to shoot images in the Burst mode depending on the Scene Selection mode (page 28).

On the Exposure Bracket

The focus and white balance are adjusted for the first image, and these settings are also used for the other images. When the exposure is manually adjusted (page 41), the exposure is shifted based on the adjusted brightness. The recording interval is approximately 0.5 seconds (DSC-W90) or 0.4 seconds (DSC-W80/W85). If the subject is too bright or too dark, you may be unable to shoot properly with the selected bracket step value. You may not be able to shoot images in the Exposure Bracket mode depending on the Scene Selection mode (page 28).
Color Mode: Changing the vividness of the image or adding special effects
You can change the brightness of the image, accompanied by effects.

(Normal)

(Vivid)
Sets the image to bright and deep color.

(Natural)

Sets the image to quiet color.

(Sepia)

Sets the image to sepia color.

(B & W)

Sets the image to monochromatic color.

(Cloudy)

Adjusts for a cloudy sky or a shady location.
(Fluorescent Light 1)/ (Fluorescent Light 2)/ (Fluorescent Light 3)
Fluorescent Light 1: Adjust for white fluorescent lighting. Fluorescent Light 2: Adjust for natural white fluorescent lighting. Fluorescent Light 3: Adjust for day white fluorescent lighting.

n (Incandescent)

Adjusts for places under incandescent lamp, or under bright lighting, such as in a photo studio.

(Flash)

Adjusts for the flash conditions.
You cannot select this item when shooting movies.
For details on the white balance, see page 9. Under fluorescent lights that flicker, the white balance function may not work correctly even though you select [Fluorescent Light 1], [Fluorescent Light 2], [Fluorescent Light 3]. Except in [Flash] modes, [White Bal] is set to [Auto] when the flash strobes.
Flash Level: Adjusting the amount of flash light
Adjusts the amount of flash light.

() (Normal) (+)

To change flash mode, see page 24.
Toward : Makes the flash level lower.
Toward +: Makes the flash level higher.
Red Eye Reduction: Reducing the red-eye phenomenon
The flash strobes two or more times before shooting to reduce the red-eye phenomenon when using the flash.

(Auto) (On) (Off)

Reduces the red-eye phenomenon whenever necessary, only when using the Face Detection Function. The flash always strobes to reduce the red-eye phenomenon. Does not use Red Eye Reduction.
Because it takes about a second until the shutter clicks, hold the camera firmly to prevent the effects of vibration. Also, do not let the subject move. Red-eye reduction may not produce the desired effects depending on individual differences, the distance to the subject, if the subject does not see the pre-strobe, or other conditions. In such a case, you can correct the red-eye phenomenon using [Retouch] in the viewing menu after shooting (page 52). When the Face Detection function is not used, the Red Eye Reduction will not function even when [Auto] is selected.
SteadyShot: Selecting the anti-blur mode
Selects the anti-blur mode.

The preset-Music differs depending on the effect you select.
Music 1 Music 2 Music 3 Music 4 Off

Interval

The default setting for a [Simple] slide show. The default setting for a [Nostalgic] slide show. The default setting for a [Stylish] slide show. The default setting for a [Active] slide show. Setting for a [Normal] slide show. No Music available.
3 sec 5 sec 10 sec 30 sec 1 min Auto
Sets the display interval of images for a [Normal] slide show.
The interval is set to suit the selected [Effects] item. The setting is fixed to [Auto] when [Normal] is not selected as the [Effects].

Repeat

On Off
Plays back images in a continuous loop. After all the images have been played back, the slide show ends.
z To add /change Music files You can transfer a desired music file from your CDs or MP3 files to the camera to playback during Slide show. You can transfer music using [ Music Tool] in (Printing, Other) on the HOME screen and the Music Transfer software (supplied) installed on a computer. For details, see pages 89 and 91. You can record up to four pieces of music on the camera (The four preset pieces (Music 1-4) can be replaced with the ones you transferred). A maximum length of each music file for music playback of the camera is 180 seconds. If you cannot playback a Music file due to damage or other malfunctions to the file, execute [Format Music] (page 89) and transfer the music again.

Viewing menu

This section explains the menu items available when you press MENU button in playback mode. For details on how to use the menu, see page 35.
(Delete): Deleting images
Selects and deletes images on the single-image screen or the index screen. see page 31
(This Image) (Multiple Images) (All In This Folder)
Deletes the image that is now selected. Selects and deletes multiple images. Deletes all the images in the selected folder.
This item has same function as [ See page 48. Slide Show] on the HOME screen.
(Retouch): Retouching still images after shooting
The trimmed image is recorded as the newest file in the selected recording folder, and the original image is retained.

(Soft Focus)

Blurs the periphery around a chosen point to signalize a subject.

1 Set the center point of the desired image to retouch with v/V/ b/B, then press MENU button. 2 Select [Level] with v/V and press z, adjust level of retouch with v/V, then press z again. 3 Adjust the desired range to retouch with W/T button. 4 Select [OK] with v/V, then press z.

(Partial Color)

Surrounds a chosen point in monochrome to signalize a subject.
1 Set the center point of the desired image to retouch with v/V/ b/B, then press MENU button. 2 Adjust the desired range to retouch with W/T button. 3 Select [OK] with v/V, then press z.

(Fisheye Lens)

Applies a fisheye effect around a chosen point.
1 Set the center point of the desired image to retouch with v/V/ b/B, then press MENU button. 2 Select [Level] with v/V and press z, adjust level of retouch with v/V, then press z again. 3 Select [OK] with v/V, then press z.

(Cross Filter)

Adds starburst effects to light sources.
1 Select [Level] with v/V and press z, adjust level of retouch with v/V, then press z again. 2 Adjust the desired length to retouch with W/T button. 3 Select [OK] with v/V, then press z.

(Trimming)

Records the zoomed playback image.
1 Press W/T button to zoom in on the trimming range. 2 Set the point with v/V/b/B, then press MENU button. 3 Selects [Image Size] with v/V and press z. Selects Image Size to record with v/V, then press z again. 4 Select [OK] with v/V, then press z.

(Red Eye Correction)

Corrects the red-eye phenomenon caused by flash. Select [OK] with v/V, then press z.
You may not be able to correct the red-eye phenomenon depending on the image.
When you select [Trimming]
The image size that you can trim may vary depending on the image. The quality of trimmed images may deteriorate.
(Protect): Preventing accidental erasure
Protects images against accidental erasure.
(This Image) (Multiple Images)
Protects/unlocks the currently selected image. Selects and protects/unlocks multiple images.

To protect an image

1 Select the images you want to protect while displaying images in single-image mode or in index mode. 2 Press MENU. 3 Select [Protect] with v/V, and select [This Image] with b/B, then press z. The image is protected and the (Protect) indicator appears on the image.
To select and protect images
1 Press MENU in single-image mode or in index mode. 2 Select [Protect] with v/V, and select [Multiple Images] with b/B, then press z. In single-image mode: 3 Select the image you want to protect with b/B on the control button, then press z. is attached to the selected image. 4 Press b/B to display other images you want to protect, then press z. 5 Press MENU. 6 Select [OK] with v, then press z. In index mode: 3 Select the image you want to protect with v/V/b/B on the control button, then press z. is attached to the selected image. 4 To protect other images, repeat step 3. 5 To select all the images in a folder, select the folder selection bar with b, then press z. is attached to the selected folder. 6 Press MENU. 7 Select [OK] with v, then press z. (Protect) indicator appears on the selected images.

6 Click [Finish].

The wizard screen closes.
To continue copying other images, disconnect the cable for multi-use terminal (page 80). Then follow the procedure explained in Stage 2: Connecting the camera and your computer on page 77.
4 Select a name and destination for
the images, then click [Next].
Stage 3-B: Copying images to a Computer
For Windows XP, follow the procedure explained in Stage 3-A: Copying images to a computer on page 77.
Image copying starts. When the copying is completed, the Other Options screen appears.
This section describes an example of copying images to the My Documents folder.
This section describes an example of copying images to the My Documents folder.
1 Double-click [My Computer] t
[Removable Disk] t [DCIM].
3 Double-click the [My Documents]
folder. Then, right-click on the My Documents window to display the menu and click [Paste].
If the Removable Disk icon is not displayed, see page 104.
2 Double-click the folder where the
image files you want to copy are stored. Then, right-click an image file to display the menu and click [Copy].
The image files are copied to the My Documents folder.
When an image with the same file name exists in the copy destination folder, the overwrite confirmation message appears. When you overwrite an existing image with a new one, the original file data is deleted. To copy an image file to the computer without overwriting, change the file name to a different name and then copy the image file. However, note that if you change the file name (page 82), you may not be able to playback that image with your camera.
On the storage destination of the image files, see (page 81).
Stage 4: Viewing images on your computer
This section describes the procedure for viewing copied images in the My Documents folder.
To delete the USB connection
Perform the procedures listed below beforehand when:
Disconnecting the cable for multi-use terminal Removing a Memory Stick Duo Inserting a Memory Stick Duo into the camera after copying images from the internal memory Turning off the camera
1 Click [Start] t [My Documents].

1 Double-click

on the tasktray.
Double-click here 2 Click (Sony DSC) t [Stop].
3 Confirm the device on the confirmation window, then click [OK]. Click [OK]. The device is disconnected.
Step 4 is unnecessary for Windows XP.
The contents of the My Documents folder are displayed.
If you are not using Windows XP, double-click [My Documents] on the desktop.
2 Double-click the desired image

The image is displayed.

Image file storage destinations and file names
The image files recorded with your camera are grouped as folders on the Memory Stick Duo. Example: viewing folders on Windows XP
Image files are named as follows. ssss stands for any number within the range from 0001 to 9999. The numerical portions of the name of a movie file recorded in movie mode and its corresponding index image file are the same. Still image files: DSC0ssss.JPG Movie files: MOV0ssss.MPG Index image files that are recorded when you record movies: MOV0ssss.THM For more information about folders, see pages 55 and 58.
A Folder containing image data recorded using a camera not equipped with the folder creating function B Folder containing image data recorded using this camera When no new folders are created, there are folders as follows:
Memory Stick Duo; 101MSDCF only Internal memory; 101_SONY only You cannot record any images to the 100MSDCF folder. The images in these folders are available only for viewing. You cannot record/playback any images to the MISC folder.
Viewing image files stored on a computer with your camera (using a Memory Stick Duo)
This section describes the process using a Windows computer as an example. When an image file copied to a computer no longer remains on a Memory Stick Duo, you can view that image again on the camera by copying the image file on the computer to a Memory Stick Duo.
Step 1 is not necessary if the file name set with your camera has not been changed. You may be unable to playback some images depending on the image size. When an image file has been processed by a computer or when the image file was recorded using a model other than that of your camera, playback on your camera is not guaranteed. When there is no folder, create a folder with your camera (page 58) first, and then copy the image file.
2 Copy the image file to the
Memory Stick Duo folder in the following order.
1Right-click the image file, then click [Copy]. 2Double-click [Removable Disk] or [Sony MemoryStick] in [My Computer]. 3Right-click the [sssMSDCF] folder in the [DCIM] folder, then click [Paste].

Dust in the air reflected the flash light and appeared in the image. This is not a malfunction.
The close-up shoot function (Macro) does not work.

(Twilight mode) or

(Landscape mode) is selected in the Scene mode (page 28).
The date and time are not displayed on LCD screen.
While shooting, the date and time are not displayed. They are displayed only during playback.
Cannot insert dates on image.
This camera does not have a feature for superimposing dates on images (page 107). By using
Picture Motion Browser, you can print or save images with the date (page 87).
The F value and shutter speed flash when you press and hold the shutter button halfway down.
The exposure is incorrect. Correct the exposure (page 41).
The screen is too dark or too bright.
Adjust the brightness of the LCD backlight (page 18).

The image is too dark.

You are shooting a subject with a light source behind the subject. Select the metering mode
(page 42) or adjust the exposure (page 41).

The image is too bright.

Adjust the exposure (page 41).
The image colors are not correct.
Set [Color Mode] to [Normal] (page 40).
Vertical streaks appear when you are shooting a very bright subject.
The smear phenomenon is occurring and white or black streaks appear on the image. This
phenomenon is not a malfunction.
Noise appears in the image when you view the screen in a dark place.
The camera is attempting to increase the visibility of the screen by temporarily brightening
the image under conditions of low illumination. There is no effect on the recorded image.
The eyes of the subject come out red.
Set [Red Eye Reduction] to [On] (page 46). Shoot the subject at a distance closer than the flash range using the flash. Light the room and shoot the subject. Retouch the image using [Red Eye Correction] (page 52).
Dots appear and remain on the screen.
This is not a malfunction. These dots are not recorded (page 2).
The image seen through the finder does not match with the actual recordable range.
The parallax phenomenon is occurring when the subject is close. In this case, to confirm the
recordable range, use the LCD screen.
Images cannot be confirmed through the finder while the digital zoom is in use.
Cannot shoot images in succession.
The internal memory or Memory Stick Duo is full. Delete unnecessary images (page 31). The battery level is low. Install charged battery pack.
Your camera cannot playback images.
Press (Playback) button (page 29). The folder/file name has been changed on your computer (page 82). When an image file has been processed by a computer or when the image file was recorded

using a model other than that of your camera, playback on your camera is not guaranteed.
The camera is in USB mode. Delete the USB connection (page 80).
The date and time are not displayed.
v (DISP) button is turned off (page 18).
The image appears rough right after playback starts.
The image may appear rough right after playback starts due to image processing. This is not a

malfunction.

The image does not appear on the TV screen.
Check [Video Out] to see if the video output signal of your camera is set to the color system of

your TV (page 64).

Check whether the connection is correct (page 70). If the USB connector of the cable for multi-use terminal is connected to another device,

disconnect it (page 80).

Your camera cannot delete an image.
Cancel the protection (page 53). You are using the Memory Stick Duo with the write-protect switch, and the switch is set to
the LOCK position. Set the switch to the recording position (page 113).
You have deleted an image by mistake.
Once you have deleted an image, you cannot restore it. We recommend that you protect
images (page 53), or use the Memory Stick Duo with the write-protect switch and set the switch to the LOCK position (page 113) to prevent accidental erasure.
You do not know if the OS of your computer is compatible with the camera.
Check Recommended computer environment on page 74 for Windows, and page 90 for

Macintosh.

Memory Stick PRO Duo is not recognized by a computer with a Memory Stick slot.
Check that the computer and the Memory Stick Reader/Writer support Memory Stick PRO
Duo. Users of computers and Memory Stick Readers/Writers made by manufacturers other than Sony should contact those manufacturers. If Memory Stick PRO Duo is not supported, connect the camera to the computer (pages 77 and 90). The computer recognizes the Memory Stick PRO Duo.
Your computer does not recognize your camera.
Turn on the camera. When the battery level is low, install the charged battery pack or use the AC adaptor (not

supplied) (page 76).

Set [USB Connect] to [Mass Storage] (page 63). Use the cable for multi-use terminal (supplied) (page 77).
Disconnect the cable for multi-use terminal from both the computer and the camera, and

connect it again firmly.

Disconnect all equipment other than the camera, the keyboard and the mouse from the USB
connectors of your computer.
Connect the camera directly to your computer without passing through a USB hub or other

device (page 77).

The software (supplied) is not installed. Install the software (page 75). Your computer does not properly recognize the device because you connected the camera and

page 87 and check what folder is used for importing.
You want to change the Folder to be imported.
Access the Import Settings screen to change Folder to be imported. You can specify a
different folder after using Picture Motion Browser to register it in Viewed folders (page 87).
The date of all imported images is displayed differently from the date on the calendar.
The date on the camera is not set correctly. Set the date and time correctly (page 68).
is displays on the screen.
The recorded data is outdated, due to changing or deleting of the name of an image or a folder.
Select [Update Database] from the [Tools] menu, and execute.

Memory Stick Duo

Cannot insert a Memory Stick Duo.
Insert it in the correct direction.
Cannot format a Memory Stick Duo.
You are using the Memory Stick Duo with the write-protect switch, and the switch is set to
You have formatted a Memory Stick Duo by mistake.
All the data on the Memory Stick Duo is deleted by formatting. You cannot restore it. We
recommend that you set the write-protect switch on the Memory Stick Duo to the LOCK position to prevent accidental erasure (page 113).
Cannot playback or record images using the internal memory.
There is a Memory Stick Duo inserted in the camera. Remove it.
Cannot copy the data stored in the internal memory to a Memory Stick Duo.
The Memory Stick Duo is full. Check the capacity (32 MB or more recommended).
Cannot copy the data on the Memory Stick Duo or the computer to the internal memory.
Data on a Memory Stick Duo or a computer cannot be copied to the internal memory.
Also see PictBridge compliant printer (as follows) in conjunction with the following items. Images are printed with both edges cut off.
Depending on your printer, the left, right, top, and bottom edges of the image may be cut off.
Especially when you print an image shot with the image size set to [16:9], the lateral end of the image may be cut off. When printing images using your own printer, cancel the trimming or borderless settings. Consult the printer manufacturer as to whether the printer provides these functions or not. When having images printed at a digital print shop, ask the shop whether they can print the images without cutting off both edges.
Cannot print images with the date.
Using Picture Motion Browser, you can print images with date (page 87). This camera does not have a feature for superimposing dates on images. However, because the
images shot with the camera include information on the recording date, you can print images with the date superimposed if the printer or the software can recognize Exif information. For compatibility with Exif information, consult the manufacturer of the printer or the software. When you print images at a shop, images can be printed with the date if you ask them to do so.

Internal memory error

Reinsert the Memory Stick
Insert the Memory Stick Duo

correctly.

The inserted Memory Stick Duo
cannot be used in your camera (page 113). The Memory Stick Duo is damaged. The terminal section of the Memory Stick Duo is dirty.

E:61:ss E:62:ss E:91:ss

A camera malfunction has occurred.

Memory Stick type error

cannot be used in your camera (page 113).
Initialize the camera (page 62), then turn the power on again.
Cannot access Memory Stick Access denied
You are using the Memory Stick with

the access controlled.

Memory Stick formatting error Internal memory formatting error
Format the media again (pages 58 and
Cannot create more folders
The folder with a name beginning with
999 exists on the Memory Stick Duo. You cannot create any folders if this is the case.

Memory Stick locked

You are using the Memory Stick Duo

File error

An error occurred while the image was
with the write-protect switch, and the switch is set to the LOCK position. Set the switch to the recording position (page 113).

playing back.

Read only folder
You have selected a folder that cannot
No memory space in internal memory No memory space on Memory Stick
Delete unnecessary images or files
be set as a recording folder on your camera. Select another folder (page 59).

(page 31).

File protect
Release the protection (page 53).

Read only memory

Your camera cannot record or delete

Image size over

You are playing back an image with size
images on this Memory Stick Duo.

No Images

No images that can be played have been
that cannot be played back on your camera.
recorded in the internal memory.

Invalid operation

You are trying to playback a file that is
recorded in this folder. The selected folder does not contain a file that can be played in a Slide Show with music.
not compatible with the camera.
You have selected a function that is not

available for movies.

(Vibration warning indicator) Folder error
A folder with the same first three digit Camera shake may occur due to
number already exists on the Memory Stick Duo (for example: 123MSDCF and 123ABCDE). Select another folders, or create a new folder (pages 58, 59).

a a*1*2

Write-protect switch Memo area
Some Memory Stick Duo cards do not have a write-protect switch. On Memory Stick Duo with this switch, the position and shape may vary depending on the Memory Stick Duo.
Do not remove the Memory Stick Duo while reading or writing data. Data may be corrupted in the following cases: When the Memory Stick Duo is removed or the camera is turned off during a read or write operation When the Memory Stick Duo is used in locations subject to static electricity or electrical noise We recommend backing up important data. Do not press down hard when you write down on the memo area. Do not attach a label on the Memory Stick Duo itself nor on a Memory Stick Duo Adaptor. When you carry or store the Memory Stick Duo, put it in the case supplied with it. Do not touch the terminal section of the Memory Stick Duo with your hand or a metal object. Do not strike, bend or drop the Memory Stick Duo. Do not disassemble or modify the Memory Stick Duo. Do not expose the Memory Stick Duo to water. Do not leave the Memory Stick Duo within the reach of small children. They might accidentally swallow it.

a*1*2*3

Memory Stick Duo, MagicGate Memory Stick Duo and Memory Stick PRO Duo are equipped with MagicGate functions. MagicGate is copyright protection technology that uses encryption technology. Data recording/playback that requires MagicGate functions cannot be performed with this camera. *2 Supports high-speed data transfer using a parallel interface. *3 640(Fine) size movies can be recorded. This product is compatible with Memory Stick Micro (M2). M2 is an abbreviation for Memory Stick Micro. A Memory Stick Duo formatted with a computer is not guaranteed to operate with this camera. Data read/write speeds differ depending on the combination of the Memory Stick Duo and the equipment used.
Do not use or store the Memory Stick Duo under the following conditions: High temperature locations such as the hot interior of a car parked in direct sunlight Locations exposed to direct sunlight Humid locations or locations with corrosive substances present
Notes on using the Memory Stick Duo Adaptor (not supplied)
To use a Memory Stick Duo with a Memory Stick compliant device, be sure to insert the Memory Stick Duo into a Memory Stick Duo Adaptor. If you insert a Memory Stick Duo into a Memory Stick compliant device without a Memory Stick Duo Adaptor, you might not be able to remove it from the device. When inserting a Memory Stick Duo into a Memory Stick Duo Adaptor, make sure the Memory Stick Duo is inserted facing in the correct direction, then insert it all the way in. Incorrect insertion may result in a malfunction. When using a Memory Stick Duo inserted into a Memory Stick Duo Adaptor with a Memory Stick compliant device, make sure that the Memory Stick Duo Adaptor is inserted facing the correct direction. Note that improper use may damage the equipment. Do not insert a Memory Stick Duo Adaptor into a Memory Stick compliant device without a Memory Stick Duo attached. Doing so may result in malfunction of the unit.

Notes on using Memory Stick PRO Duo (not supplied)
Memory Stick PRO Duo with a capacity up to 8 GB have been confirmed to operate properly with this camera.
Notes on using Memory Stick Micro (not supplied)
To use a Memory Stick Micro with this camera, be sure to insert the Memory Stick Micro into an M2 Adaptor as large as of Duo size. If you insert a Memory Stick Micro into the camera without an M2 Adaptor as large as of Duo size, you might not be able to remove it from the camera. Do not leave the Memory Stick Micro within the reach of small children. They might accidentally swallow it.

On the battery pack

On charging the battery pack
We recommend charging the battery pack in an ambient temperature of between 10C to 30C (50F to 86F). You may not be able to efficiently charge the battery pack outside of this temperature range. The battery life varies according to how it is stored and the operating conditions and environment in which each battery pack is used.
Effective use of the battery pack
Battery performance decreases in low temperature surroundings. So, the time that the battery pack can be used is shorter in cold places. We recommend the following to ensure longer battery pack use: Put the battery pack in a pocket close to your body to warm it up, and insert it in your camera immediately before you start shooting. The battery pack will run out quickly if you use the flash or zoom frequently. We recommend having spare battery packs handy for two or three times the expected shooting time, and making trial shots before taking the actual shots. Do not expose the battery pack to water. The battery pack is not water-resistant. Do not leave the battery pack in extremely hot places, such as in a car or under direct sunlight.
How to store the battery pack
If the battery pack is not to be used for a long time, fully charge it and then fully use it up once a year on your camera before storing the battery pack in a dry, cool place. Repeat this charging and using up once a year to maintain the battery packs function. To use the battery pack up, leave your camera in slide show (page 48) playback mode until the power goes off. To prevent staining the terminal, shortcircuiting, etc., be sure to use a supplied battery case when carrying and storing.

On battery life

The battery life is limited. Battery capacity decreases little by little as you use it more and more, and as time passes. If the battery operating time seems shortened considerably, a probable cause is that the battery pack has reached the end of its life. Buy a new battery pack.

On the battery charger

Do not charge any other battery pack other than the NP-BG type battery packs in the battery charger supplied with your camera. Batteries other than the specified kind may leak, overheat, or explode if you attempt to charge them, posing a risk of injury from electrocution and burns. Remove the charged battery pack from the battery charger. If you leave the charged battery pack in the charger, battery life may be shortened. When the CHARGE lamp flashes, this may indicate a battery error or that a battery pack other than the specified type have been inserted. Check that the battery pack is the specified type. If the battery pack is the specified type, remove the battery pack, replace it with new one or another one and check if the battery charger operates correctly. If the battery charger operates correctly, a battery error may have occurred. If the battery charger is dirty, charging may not be performed successfully. Clean the battery charger with dry cloth, etc.

Adjusting EV.19, 41 AE/AF lock indicator.22, 44 AF Illuminator..65 AF lock..44 AF Mode.66 AF range finder frame..42 Aperture..8 Auto Adjustment mode.22 Auto Focus..7 Auto Orientation.67 Auto Review..67 Viewing image files stored on a computer with your camera.. 82 Windows.. 73 Connecting Computer.. 77 Printer.. 94 TV.. 70 Copy.. 60 Copying images to your computer.. 76 Create REC. Folder. 58 Cross Filter.. 52 Flash mode..24 Fluorescent Light 1, 2, 3.45 Focus..7, 23, 42 Focus preset.43 Folder.55 Changing..59 Creating..58 Selecting.55 Format..58, 61 Format Music.89 Function Guide.62

Grid Line..65

B & W..40 Battery charger..116 battery pack..115 Beach mode.27 Beep..62 Blur...7 Burst..39
Date. 68, 87, 95 Daylight.. 45 Delete.. 51 Format. 58, 61 Deleting images.. 31 Digital Zoom. 66 DirectX.. 74 DISP.. 18 Download Music. 89 DPOF.. 54, 96
High Sensitivity mode..27 Histogram..18, 19 Holding the camera.7, 22 HOME..33
Identifying parts..12 Image file storage destinations and file names.81 Image quality.10 Image Size..37 Image size..10 Incandescent..45 Index Display.48 Index screen.30 Indicator..14 Initialize..62 Install.75
Cable for multi-use terminal..70, 77, 94 Center AF..43 Center-weighted metering.42 Change REC. Folder.59 Clock Settings..68 Cloudy..45 Color..9 Color Mode..40 COMPONENT.63 Computer..73 Copying images.76, 90 Macintosh..90 Recommended environment.74, 90 Software..75
EV.. 41 Exposure.. 8 Exposure Bracket.. 39 Extension.. 82
Face Detection.. 38 File name.. 81 File storage destination. 81 Fisheye Lens.. 52 Flash (White Bal).. 46 Flash forced off.. 24 Flash forced on. 24 Flash Level.. 46
Internal memory.20 Internal Memory Tool.61 ISO.8, 41

JPG..81

Landscape mode.27 Language Setting.69 LCD backlight..18 LCD Screen.18
Optical zoom. 23, 66 OS.. 74, 90 Overexposure.. 8
SETUP.. 47 Shooting. 37 Movies. 22, 23 Still image. 22 Shooting Settings 1.. 65 Shooting Settings 2.. 67 Shutter speed. 8 Single. 66 Single Image.. 48 Slide Show.. 48, 51 Slow synchro. 24 Smart zoom. 66 Snow mode.. 27 Soft Focus.. 51 Soft Snap mode.. 27 Software. 75, 83, 89 Spot AF.. 43 Spot metering.. 42 Spot metering cross hairs.. 42 SteadyShot.. 47
PAL.. 64 Partial Color.. 51 PC... 73 PictBridge.. 63, 93 Picture Motion Browser. 83 Pixel.. 10 Playback zoom. 29 Precision digital zoom. 66 Pressing halfway down.. 7 Print.. 54, 92 Print order mark. 96 Printing at a shop.. 96 Printing directly. 93 Program Auto mode. 21 Protect.. 53
Macintosh computer.90 Recommended environment.90 Macro.24 Main Settings 1.62 Main Settings 2.63 Manage Memory.58 Map View..86 Mass Storage.63 Memory Stick Duo..113 Memory Stick Tool..58 Menu Items..36 Shooting.37 Viewing..51 Metering Mode.42 Mode Dial..21 Monitor..66 MPG..81 Multi AF.42 Multi Connector.70, 77, 94 Multi-pattern metering.42 Music.50 Music Tool..89 Music Transfer.89, 91