4-165-483-11(1)

DVD Home Theatre System
Operating Instructions DAV-DZ170/DZ171/DZ175

2010 Sony Corporation

Owners Record

WARNING

Caution The use of optical instruments with this product will increase eye hazard.
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To reduce the risk of fire, do not cover the ventilation opening of the apparatus with newspapers, tablecloths, curtains, etc. Do not place the naked flame sources such as lighted candles on the apparatus. Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Indoor use only.

CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
The model and serial numbers are located on the rear exterior of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. DAV-DZ170/ DAVDZ171/DAV-DZ175 Serial No.______________ The following FCC statement applies only to the version of this model manufactured for sale in the U.S.A. Other versions may not comply with FCC technical regulations. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna (aerial). Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Important Safety Instructions
1) 2) 3) 4) 5) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/ accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/
For the customers in the U.S.A.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

For the customers in Canada
To reduce the risk of fire or electric shock, do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on the apparatus. ENERGY STAR is a U.S. registered mark. As an ENERGY STAR partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

About MPEG-4 Visual

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NONCOMMERCIAL USE OF A CONSUMER FOR DECODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (MPEG-4 VIDEO) THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP:// WWW.MPEGLA.COM
About These Operating Instructions
The instructions in these Operating Instructions describe the controls on the remote. You can also use the controls on the unit if they have the same or similar names as those on the remote. The Control Menu items may vary depending on the area. DVD may be used as a general term for a DVD VIDEO, DVD+RW/ DVD+R, and DVD-RW/ DVD-R. Measurements are expressed in feet (ft) for North American models. The default setting is underlined.

Table of Contents

Precautions... 3 About These Operating Instructions. 4 Playable Discs/Files on a USB Device.. 6 Package Contents.. 10 Index to Parts and Control.. 11 Guide to the Control Menu.16

Settings

Changing the Brightness of the Front Panel Display.. 53 Setting the Demonstration Mode to On/Off.. 53 Reperforming the Quick Setup. 53 Set the System to Standby Mode Automatically.. 53 Performing Further Settings.. 54

Getting Started

Step 1: Installing the System. 19 Step 2: Connecting the System. 21 Step 3: Setting up the System.. 26

Additional Information

Precautions.. 62 Troubleshooting. 64 Specifications.. 70 Index... 75

Playback

Playing a Disc.. 30 Playing Files on a Disc/USB Device. 30 Other Playback Operations.32 Selecting the Playback Mode. 35 Displaying the Information of a Disc/ USB Device. 39 Enjoying the Audio/Video of the Connected Component.40

Notes about USB devices

This system supports Mass Storage Class (MSC) devices. This system is not guaranteed to operate with all USB devices or memories. Although there are variety of complex functions for USB devices, the playable contents of USB devices connected to the system are music, photo, and video contents only. For details, refer to the operating instructions of the USB device. When a USB device is inserted, the system reads all the files on the USB device. If there are many folders or files on the USB device, it may take a long time to finish reading the USB device. Do not connect the system and the USB device through a USB hub. With some connected USB devices, there may be a delay before an operation is performed by this system. The playback order for the system may differ from the playback order of the connected USB device. Always turn off the system before removing the USB device. Removing the USB device while the system is on may corrupt the data on the USB device. Before using a USB device, make sure that no virus-ridden files are on the USB device.

Package Contents

Main unit

Speaker packages

DAV-DZ170/DAV-DZ171 DAV-DZ175
Speaker cords (1 set) (red/white/green/gray/blue)

Foot pads (1 set)

Accessories
Remote commander (remote) (1) FM wire antenna (aerial) (1)
HDMI cable (1) (DAV-DZ171 only)
R6 (size AA) batteries (2)

Calibration mic (1)

Video cord (1)
Operating Instructions Quick Setup Guide Easy Setup Disc (DVD)
Index to Parts and Control
For more information, refer to the pages indicated in parentheses.

Front panel

A Disc tray B Front panel display (page 12) C (remote sensor)

I FUNCTION

Selects the playback source.
J Play operation buttons Z (open/close)
Receives the remote signal. Point the remote toward here when using the remote.

D MASTER VOLUME control

Opens or closes the disc tray.

N (play)

Adjusts the systems volume.

E REC TO USB (page 49)

Starts or re-starts playback.

x (stop)

Transfers tracks/MP3 files onto a USB device. Lights up during transfer of tracks/MP3 files.

F (USB) port (pages 24, 30)
Stops playback and remembers the stop point (resume point).

K "/1 (on/standby)

Turns on the unit, or sets it to standby mode.
Used for connecting a USB device or iPod.
G AUDIO IN jack (page 24)
Used for connecting other components, such as a portable audio source.
H A.CAL MIC jack (page 26)
Used for connecting the calibration mic.

Front panel display

A Playing status indicator B SLEEP indicator

F HDMI indicator

Flashes when the sleep timer is set.
C System status display D TUNED indicator (Radio only)
Lights up when a signal is established between a TV and the unit via HDMI.
G Surround format indicator H SA-CD indicator
Lights up when a station is received.
E ST indicator (Radio only)
Lights up when a Super Audio CD/CD is loaded.
Lights up when stereo sound is received.

Rear panel

SPEAKERS

SUR R SUR L

ANTENNA

COAXIAL 75 FM

TV/CABLE

DIGITAL IN

FRONT R

FRONT L

SUBWOOFER

CENTER

OPTICAL

COAXIAL

COMPONENT VIDEO OUT

VIDEO OUT

R AUDIO IN
A SPEAKERS jacks (page 21) B HDMI OUT jack (page 22) C TV/CABLE (DIGITAL IN OPTICAL/ COAXIAL) jacks (page 22) D COMPONENT VIDEO OUT jacks (page 22)
E VIDEO OUT jack (page 22) F TV/CABLE (AUDIO IN R/L) jacks (page 22) G ANTENNA (COAXIAL 75 FM) jack (page 24)

Remote control

B Buttons with black/white text labels
Function selection buttons (pages 30, 40, 42)

THEATER

ONE-TOUCH PLAY

BRAVIA Sync 1 2

DVD/CD FM
Select the playback source. The system is turned on automatically when you press the function selection button while the system is turned off.
DVD/CD FM USB TV/CABLE AUDIO IN FUNCTION

TV/ CABLE

AUDIO IN

FUNCTION

TIME/ TEXT

SOUND MODE

SYSTEM MENU

SUBTITLE D.TUNING

TV INPUT

ANGLE MEM SEL

DVD TOP MENU

DVD MENU MUTING VOLUME

Selects the functions in sequence.

RETURN

PRESET

TIME/TEXT (page 39)

DISPLAY
Changes the information in the front panel display.

SOUND MODE (page 46)

TUNING SHIFT

TUNING

Selects the sound mode.

Selected row
If [MEDIA] is set to [MUSIC/PHOTO] and [FILE] does not appear, press DISPLAY again.
When playing files, you can select the next folder by continuing to press > (c for JPEG image files) after the last file on the current folder, but you cannot return to the previous folder by pressing.(C for JPEG image files). To return to the previous folder, select the folder from the folder list. You cannot rotate the JPEG image file when you set [JPEG RESOLUTION] in [HDMI SETUP] to [(1920 1080i) HD ] or [(1920 1080i) HD] (page 56).
Press X/x to select the desired number of the title, chapter, track, scene, etc., then press.
You can also select the number by pressing the number buttons while holding down SHIFT.
98( 99) 13( 99) T 0: 03: 17
Playing a specific title/ chapter/track/scene, etc.
To select the title/chapter/track/ scene/index/folder/file number for playback
If you make a mistake, press CLEAR while holding down SHIFT to cancel the number.
To select a scene using the time code
Press X/x to select the search method, then press.
[TITLE/SCENE/TRACK] [CHAPTER/INDEX] [TRACK] [INDEX] [FOLDER] [FILE]

DISPLAY. [TIME], then

Press X/x to select press.
Input the time code using the number buttons while holding down SHIFT, then press.
For example, to find a scene at 2 hours, 10 minutes, and 20 seconds after the beginning: press 2, 1, 0, 2, 0 ([2:10:20]) while holding down SHIFT.

x DVD-VR

You cannot search for a scene on a DVD+RW using the time code.
You can toggle audio tracks when a disc contains multiple audio tracks.
x VIDEO CD/CD/DATA CD (MP3 file)/DATA DVD (MP3 file)/USB device (audio file)

Changing angles

Press ANGLE during playback to select the desired angle.
You can change the sound track. [STEREO]: The stereo sound. [1/L]: The sound of the left channel (monaural). [2/R]: The sound of the right channel (monaural).

x Super VCD

Displaying subtitles
Press SUBTITLE during playback to select the desired subtitle language.

iPod models that can be operated via USB
You can operate an iPod using the buttons on the remote by connecting the iPod via the (USB) port to the system. The battery of the iPod is charged via the system. The iPod models that can be operated via USB are as follows. Update your iPod with the latest software before using it with the system.
The iPod is charged when connected to the system while the system is turned on. You cannot transfer songs onto the iPod. Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod connected to this unit. This product has been designed specifically to work with iPod and has been certified to meet Apple performance standards.
To change the preset number
Presetting Radio Stations
You can preset 20 FM stations.
Current station Current band and preset number

FM FM 10 : 88.00 MHz

Select the desired preset number by pressing PRESET +/ (page 42), then perform the procedure from Step 3.

Listening to the Radio

Preset radio stations in the systems memory first (see Presetting Radio Stations (page 42)).
Press FM. Press PRESET +/ repeatedly to select the preset station. Adjust the volume by pressing VOLUME +/.
Press FM. Press and hold TUNING +/ until the auto scanning starts.
To listen to radio stations when you know the frequencies
Press D.TUNING in Step 2, press the number buttons while holding down SHIFT to select the frequencies, then press.
Scanning stops when the system tunes in a station. TUNED appears in the front panel display. When a stereo program is received, ST also appears in the front panel display.
To listen to non-preset radio stations
Use manual or automatic tuning in Step 2. For manual tuning, press TUNING +/ repeatedly. For automatic tuning, press and hold TUNING +/. The automatic tuning stops automatically when the system receives the radio station. To stop the automatic tuning manually, press TUNING +/ or x.
Press SYSTEM MENU. Press X/x to select MEMORY. Press or c.
A preset number appears in the front panel display.
If an FM program is noisy
Press X/x to select the preset number you want.
If an FM program is noisy, you can select monaural reception. There will be no stereo effect, but reception will improve.
Press SYSTEM MENU. Press X/x to select FM MODE.
COMPLETE appears in the front panel display, and the station is stored.
Repeat Steps 2 to 7 to store other stations. Press SYSTEM MENU. Press or c.
Press X/x to select MONO.

Enhancing compressed sound
You can enhance compressed sound such as an MP3 file. This effect is activated automatically when all the following conditions are satisfied: The function is set to AUDIO IN or USB. SUR.SETTING is set to A.F.D. STD or A.F.D. MULTI (page 44).
To turn off the sound effect
Select other than A.F.D. STD or A.F.D. MULTI for SUR.SETTING (page 44).
Make sure that the system and your TV are connected with an HDMI cable. Turn on your TV and press [/1 to turn on the system. Switch the input selector on your TV so that the signal from the system through the HDMI input appears on the TV screen. Set the Control for HDMI function of your TV.
Using the Control for HDMI Function for BRAVIA Sync
This function is available on TVs with the BRAVIA Sync function. By connecting Sony components that are compatible with the Control for HDMI function with an HDMI cable, operation is simplified as below: System Power Off (page 47) One-Touch Play (page 48) Theater Mode (page 48) System Audio Control (page 48) Volume Limit (page 48) Remote Easy Control (page 48) Language Follow (page 48) Control for HDMI is a mutual control function standard used by CEC (Consumer Electronics Control) for HDMI (High-Definition Multimedia Interface).
For details of the setting of your TV, refer to the operating instructions of your TV.
On the system, press DVD/CD. Press DISPLAY while the system is in stop mode. Press X/x to select then press. [SETUP],
Press X/x to select [CUSTOM], then press. Press X/x to select [HDMI SETUP], then press. HDMI], then press.
10 Press X/x to select [CONTROL FOR 11 Press X/x to select [ON], then press
Turning the system off in sync with your TV
(System Power Off) When you turn your TV off by using the POWER button on your TVs remote or TV [/1 on the systems remote, the system turns off automatically.
Depending on the connected component, the Control for HDMI function may not work. Refer to the operating instructions of the component.
Preparing the Control for HDMI function
(Control for HDMI - Easy Setting) If your TV is compatible with the Control for HDMI - Easy Setting function, you can set the systems [CONTROL FOR HDMI] function automatically by setting your TV. For details, refer to the operating instructions of your TV. If your TV is not compatible with the Control for HDMI - Easy Setting function, set the Control for HDMI function of the system and TV manually.
This function depends on the settings of your TV. For details, refer to the operating instructions of your TV. Depending on the status of the system (ex. while playing a CD), the system may not turn off automatically.
Watching a DVD by a single button press

(One-Touch Play)

Press ONE-TOUCH PLAY
You can also operate the System Audio Control function via the TV menu. You can operate the volume and mute control of the system via the TV remote.

[LANGUAGE SETUP] (page 54) [VIDEO SETUP] (page 55) [HDMI SETUP] (page 56) [AUDIO SETUP] (page 57) [SYSTEM SETUP] (page 58) [SPEAKER SETUP] (page 60)

Selected setting

To reset all of the [SETUP] settings
To reset all of the [SETUP] settings, see [RESET] (page 59).

Example: [VIDEO SETUP]

VIDEO SETUP TV TYPE: PROGRESSIVE (COMPONENT OUT): 4:3 OUTPUT: BLACK LEVEL: BLACK LEVEL (COMPONENT OUT): PAUSE MODE: 16:9 OFF FULL ON OFF AUTO
Setting the display or sound track language
[LANGUAGE SETUP] Set various languages for the on-screen display or sound track.
x [OSD] (On-Screen Display)

Setup items

You can switch the display language on the TV screen.

x [MENU]

You can switch the language for the discs menu.

x [AUDIO]

You can switch the language of the sound track. When you select [ORIGINAL], the language given priority on the disc is selected.

x [SUBTITLE]

[4:3 PAN SCAN]: Select this when you connect a 4:3 standard TV. The system automatically displays a wide picture on the entire screen and cuts off the portions that do not fit.
You can switch the language of the subtitles recorded on the DVD VIDEO. When you select [AUDIO FOLLOW], the language for the subtitles changes according to the language you selected for the sound track.
x [PROGRESSIVE (COMPONENT OUT)]
When you select a language in [MENU], [AUDIO], or [SUBTITLE] that is not recorded on the DVD VIDEO, one of the recorded languages will be automatically selected (depending on the disc, the language may not be selected automatically).
You can set the progressive signal that is output from the COMPONENT VIDEO OUT jacks to on/off. For details, see To select the type of video signal output from the COMPONENT VIDEO OUT jacks (page 29). [OFF]: The system outputs interlace signals. [ON]: The system outputs progressive signals. When you select [ON], follow the Steps below.
If you select [OTHERS t] in [MENU], [AUDIO], and [SUBTITLE], select and enter a language code from Language Code List (page 74) using the number buttons.

Select [ON], then press

Settings for the display
[VIDEO SETUP] Select settings according to your TV.

x [TV TYPE]

The system outputs a progressive signal. If you select [NO], the system will not output a progressive signal.
You can select the aspect ratio of the connected TV. [16:9]: Select this when you connect a widescreen TV or a TV with a wide-screen mode.

x [PAUSE MODE]

(DVD VIDEO/DVD-R/DVD-RW only)

x [CONTROL FOR HDMI]

This function is available when you connect the system and TV that is compatible with the Control for HDMI function with an HDMI cable. [ON]: On. You can operate mutually between components that are connected with an HDMI cable. [OFF]: Off.

x [VOLUME LIMIT]

You can select the picture in pause mode. [AUTO]: The picture, including subjects that move dynamically, is output with no jitter. This setting is for normal usage. [FRAME]: The picture, including subjects that do not move dynamically, is output in high resolution.
When the System Audio Control (page 48) is activated, loud sound may be output depending on the volume level of the system. You can prevent this by limiting the maximum level of the volume when the System Audio Control function activates. [OFF]: Off. [LEVEL3]: Maximum volume level is set to 10. [LEVEL2]: Maximum volume level is set to 15. [LEVEL1]: Maximum volume level is set to 20.
This function is available only when [CONTROL FOR HDMI] is set to [ON].

x [YCBCR/RGB (HDMI)]

You can select the type of HDMI signal output from the HDMI OUT jack. [YCBCR]: The system outputs YCBCR signals. [RGB]: The system outputs RGB signals.

x [AUDIO (HDMI)]

Settings for the audio

[AUDIO SETUP]

x [SPEAKER FORMATION]
You can select the audio output status from the HDMI OUT jack. [OFF]: The system does not output sound from the HDMI OUT jack. [ON]: The system outputs audio signals by converting Dolby Digital, DTS, or 96 kHz/24bit PCM signals to 48 kHz/16-bit PCM.
Depending on the shape of the room, you may not be able to install some speakers. For better surround sound, Sony recommends that first you decide the position of the speakers.
Press C/c to select a setting, then press.
When you set the function to other than DVD/CD or USB, the system does not output the sound from the HDMI OUT jack even if you set [AUDIO (HDMI)] to [ON].

x [JPEG RESOLUTION]

You can select the resolution of JPEG image files output from the HDMI OUT jack. [SD ]: The system outputs standard resolution with a black frame. [HD ]: The system outputs HD resolution with a black frame. [HD]: The system outputs the HD resolution without a black frame. [(1920 1080i) HD ]: The system outputs full size HD resolution with a black frame. [(1920 1080i) HD]: The system outputs full size HD resolution without a black frame.

Other Settings

[SYSTEM SETUP]
Press C/c to select [YES] or [NO], then press. Disconnect the calibration mic when the measurement completes correctly.

x [SCREEN SAVER]

You can reduce the damage to the display device (ghosting). Press any button (e.g., N) to cancel the screen saver. [ON]: The screen saver image appears if you do not operate the system for about 15 minutes. [OFF]: Off.

x [BACKGROUND]

The system outputs a loud test sound when [AUTO CALIBRATION] starts. You cannot turn the volume down. Give consideration to children and neighbors. The measurement for [SUBWOOFER] is always [YES] and [SPEAKER SETUP] returns to the default setting when you perform [AUTO CALIBRATION].
You can select the background color or picture on the TV screen.
[JACKET PICTURE]: The jacket picture (still picture) appears, but only when the jacket picture is already recorded on the disc (CDEXTRA, etc.). If the disc does not contain a jacket picture, a preset picture stored in the system appears. [GRAPHICS]: A preset picture stored in the system appears. [BLUE]: The background is blue. [BLACK]: The background is black.

x [PARENTAL CONTROL]

enter a new 4-digit password, replace the disc in the unit and press N. When the display for entering your password appears, enter your new password.

Changing the password

Enter your 4-digit password using the number buttons, then press. Press X/x to select [CHANGE PASSWORD t], then press.
Enter a new 4-digit password using the number buttons, then press.
The [PARENTAL CONTROL] function allows you to restrict playback of DVDs that have ratings. Scenes may be blocked or replaced with different scenes.
If you make a mistake entering your password, press C before you press then input the correct number.
Enter or re-enter your 4-digit password using the number buttons, then press. Press X/x to select [STANDARD], then press. Press X/x to select a geographic area as the playback limitation level, then press.
To confirm your password, re-enter it using the number buttons, then press.

x [MULTI-DISC RESUME]

This system recalls the point where you stopped the disc the last time it was played and resumes playback from that point the next time you insert the same disc. [ON]: The system stores the resume points in memory for up to 10 discs. [OFF]: The system does not store the resume points in memory. Playback restarts at the resume point only for the current disc in the unit.
When you select [OTHERS t], select and enter a standard code from Parental Control Area Code List (page 74) using the number buttons.
Press X/x to select [LEVEL], then press. Press X/x to select the desired level, then press.
When the resume playback memory is full, the resume playback point for the earliest disc is deleted.
The lower the value, the stricter the limitation.
To turn off the [PARENTAL CONTROL] function

x [RESET]

Set [LEVEL] to [OFF] in Step 5.
To play a disc for which [PARENTAL CONTROL] is set
You can return the [SETUP] settings other than [PARENTAL CONTROL] to the default settings.
When you load the disc and press N, the display for entering your password appears. Enter your 4-digit password using the number buttons, then press.
You can also quit the process and return to the Control Menu by selecting [NO] here. Do not press [/1 while resetting the system as it takes a few seconds to complete.
If you forget your password, enter 199703 using the number buttons, then press. The display will ask you to enter a new 4-digit password. After you
The [MEDIA], [INTERVAL], [EFFECT], and [MULTI/2CH] settings also return to the default settings.
0.9 to 6.9 meters for North American models. to 6.9 meters for North American models.
Settings for the speakers

[SPEAKER SETUP]

x [DISTANCE (SURROUND)]
You can adjust the speaker settings manually without performing the Quick Setup. Select the speakers you will use, set the speaker distance from your listening position, and then adjust the sound level for each speaker. You can adjust the sound level by using the [TEST TONE] function.

x [CONNECTION]

[FRONT]
Set the distance for the surround speakers from the listening position. For the best possible surround sound, place all speakers at the same distance from the listening position. The distance can be between 1.0 to 7.0 meters* (0 to 23 ft). If you cannot place surround speakers at the same distance, you can move the surround speakers up to 5.0 meters (16 ft) closer to the listening position. [L/R] 3.0 m/10 ft: Set the surround speaker distance.
* 0.0 to 6.9 meters for North American models.

[CENTER]

[YES]: Normally select this. [NONE]: Select this if no center speaker is used.

[SURROUND]

Depending on the input stream, the [DISTANCE] setting may not be effective.
[YES]: Normally select this. [NONE]: Select this if no surround speakers are used.

[SUBWOOFER]

x [LEVEL (FRONT)]
When you change the [CONNECTION] setting, the [STANDARD] of [SPEAKER FORMATION] setting remains the same, but the other settings of [SPEAKER FORMATION] return to [STANDARD].
You can adjust the sound level of the front speakers, center speaker, and subwoofer. You can set the parameters from 6.0 dB to 0 dB for [L/R], and from 6.0 dB to +6.0 dB for [CENTER] and [SUBWOOFER]. Be sure to set [TEST TONE] to [ON] for easy adjustment. [L/R] 0.0 dB: Set the front speaker level. [CENTER] 0.0 dB: Set the center speaker level. [SUBWOOFER] +2.0 dB: Set the subwoofer level.

x [LEVEL (SURROUND)]

x [DISTANCE (FRONT)]
Set the distance of the front and center speakers from the listening position. For the best possible surround sound, place all speakers at the same distance from the listening position. The distance can be between 1.0 to 7.0 meters1) (3 to 23 ft) for the front speakers, and 0.0 to 7.0 meters2) (0 to 23 ft) for the center speaker. If you cannot place the center speaker at the same distance, you can move the center speaker up to 1.6 meters closer to the listening position. [L/R] 3.0 m/10 ft: Set the front speaker distance. [CENTER] 3.0 m/10 ft: Set the center speaker distance.
You can adjust the sound level of the surround speakers. You can set the parameter from 6.0 dB to +6.0 dB. Set [TEST TONE] to [ON] for easy adjustment. [L/R] 0.0 dB: Set the surround speaker level.

x [TEST TONE]

You can adjust the sound level of the speakers by using the [TEST TONE] function. [OFF]: The test tone is not emitted from the speakers.
[ON]: The test tone is emitted from each speaker in sequence while adjusting the level. Adjust the sound level as follows.
Set the [TEST TONE] to [ON]. Press C/X/x/c repeatedly to select the desired speaker and the level, then press. Repeat Step 2. Press C/X/x/c to set [TEST TONE] to [OFF] after adjusting the speaker level.

Emission Duration: Continuous Laser Output: Less than 44.6 W * This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture. Laser Diode Properties

Signal format system

Subwoofer DAV-DZ170/DAV-DZ171 (SS-WS102)
Speaker system Speaker unit Rated impedance Dimensions (approx.) Subwoofer Bass reflex 180 mm (7 1/8 in) cone type 3 ohms 225 mm 395 mm 315 mm (8 7/8 in 15 5/8 in 12 1/2 in) (w/h/d) 6.5 kg (14 lb 6 oz) Subwoofer Bass reflex 160 mm (6 3/8 in) cone type 3 ohms 169 mm 300 mm 320 mm (6 3/4 in 11 7/8 in 12 5/8 in) (w/h/d) 5.3 kg (11 lb 11 oz)

USB Section

(USB) port: Maximum current: 500 mA PLL quartz-locked digital synthesizer

Tuner Section

System Tuning range North American models:
87.5 MHz - 108.0 MHz (100 kHz step) Other models: 87.5 MHz - 108.0 MHz (50 kHz step) Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced Intermediate frequency 10.7 MHz
Mass (approx.) Speaker system Speaker unit Rated impedance Dimensions (approx.)

DAV-DZ175 (SS-WS101)

Video Section
Outputs VIDEO: 1 Vp-p 75 ohms COMPONENT: Y: 1 Vp-p 75 ohms

Mass (approx.)

120 V AC, 60 Hz On: 170 W Standby: 0.2 W* * Valid when the system is in the following status: DEMO is set to OFF. [CONTROL FOR HDMI] is set to [OFF]. Dimensions (approx.) 430 mm 66 mm 385 mm (17 in 2 5/8 in 15 1/4 in) (w/h/d) incl. projecting parts Mass (approx.) 4.4 kg (9 lb 12 oz) Power requirements Power consumption
PB/CB, PR/CR: 0.7 Vp-p 75 ohms
HDMI OUT: Type A (19 pin)
Speakers Front (SS-TS102)
Speaker system Speaker unit Rated impedance Dimensions (approx.) Full range Bass reflex 65 mm (2 5/8 in) cone type 3 ohms 103 mm 164 mm 85 mm (4 1/8 in 6 1/2 in 3 3/8 in) (w/h/d) 0.5 kg (1 lb 2 oz) Full range Bass reflex, Magnetically Shielded 65 mm (2 5/8 in) cone type 3 ohms 265 mm 94 mm 70 mm (10 1/2 in 3 3/4 in 2 7/8 in) (w/h/d) 0.6 kg (1 lb 6 oz) Full range Bass reflex 65 mm (2 5/8 in) cone type 3 ohms 103 mm 164 mm 85 mm (4 1/8 in 6 1/2 in 3 3/ 8 in) (w/h/d) 0.5 kg (1 lb 2 oz)
Supported file format MP3 (MPEG 1 Audio Layer-3)
File Extension: Bitrate: Sampling frequencies: File Extension: Bitrate: Sampling frequencies: File Extension: Bitrate: Sampling frequencies: mpkbps - 320 kbps 32/44.1/48 kHz wma 48 kbps - 192 kbps 44.1 kHz m4a 48 kbps - 320 kbps 44.1 kHz MP4 File Format mp4/m4v MPEG4 Simple Profile (AVC is not compatible.) 4 Mbps 30 fps AAC-LC (HE-AAC is not compatible.)

Center (SS-CT101)

DAV-DZ170

Key Features 1000 watt (167x5+165 3ohm, 1kHz, 10%THD) 5.1 channel surround sound DVD upscaling to near HD picture quality via HDMI 1 BRAVIA Sync controls compatible devices w/ one remote2 Digital Cinema Audio Calibration for quick speaker set-up Easy Set-up Disc is included to guide you through the set-up process Smart Remote Control Multiple format disc playback3 iPod compatibility and connectivity4 Rip your CDs to your USB drive5 Key Technologies
Sony BRAVIA Theater System
1000 watt (167x5 + 165, 3 ohm, 1kHz, 10%THD) 5.1 channel surround sound Enough power to
get the most from the included speakers and subwoofer.
Upscales DVDs to Near HD via HDMI? Play and upscale the quality of your DVDs to near HD
quality when using an HDMI cable (sold separately) and compatible HDTV.1
BRAVIA Sync Capable Conveniently operate and control all your HDMI connected BRAVIA
Sync devices with one remote including: Blu-ray Disc Players, BRAVIA HDTVs, home theater products, Handycam Camcorders and Cyber-shot Digital Cameras.
Digital Cinema Auto Calibration - Quick Speaker Set Up Ensure you get the best sound
experience from your surround sound system with Digital Cinema Auto Calibration. Simply place the included microphone where you will be seated and settings are automatically optimized based on the distance, delays and placement of your speakers.
Easy Set-up DVD Easy set-up DVD and a one page guide, gives basic speaker set-up instructions
and simple connection options.
Smart Remote Control Convenient, one-touch access for key activities like watching your TV,
listening to the radio, watching a DVD, or playing back MP3s from the USB port.
Multiple format disc playbackMultiple format disc playback View movies and photos and listen
to music using this DVD player with multiple format playback. The DAV-DZ170 supports DVD/DVDRW/DVD-R/DVD+RW/DVD+R DL and CD-R/CD-RW discs plays WMA, AAC, and JPEG files.3
iPod compatibility and connectivity Rip CDs to your USB driveEasy MP3 ripping to your USB drive so you can take your favorite songs on-the-go. Connect your iPod product to the front USB port and access all of your favorite

music.4

Rip CDs to your USB drive Easy MP3 ripping to your USB drive so you can take your favorite songs

on-the-go.

Features
DVD (VR Mode) Playback: Yes2 DVD Playback: Yes2 DVD+R DL Read Compatibility: Yes2 DVD+R Read Compatibility: Yes2 DVD+RW Read Compatibility: Yes2 DVD-R Read Compatibility: Yes2 DVD-RW Read Compatibility: Yes2 JPEG Playback: Yes1 Precision Cinema Progressive Technology: Yes Progressive Scan: Yes VCD Playback: Yes1 Play Mode: Shuffle (CD/VCD/SA-CD); Program (CD/VCD); Repeat (DVD/CD/VCD/SA-CD)

UPC Code: 027242781672

1. Requires HDTV with HDMI connector (sold separately) and equivalent display capability. Image quality will vary. 2. Works with other BRAVIA Sync or Theatre Sync labeled home audio/video products when connected via HDMI interface. 3. DVD Media/Formats are not universally compatible. Playback depended on recording conditions. 4. This device supports the following models: iPod touch, iPod classic, iPod Nano 1st, 2nd & 3rd generation, iPod 4th& 5th generation &iPod Mini. Using the iPods USB connector. 5. This feature may not be compatible with all CDs. 2010 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony, BRAVIA, their respective logos are trademarks of Sony. iPhone,iPod and iPod touch are trademarks of Apple Computers, Inc. HDMI is a trademark of HDMI Licensing LLC. dts is a trademark of DTS, Inc. Dolby is a registered trademark of Dolby Laboratories. All other trademarks are trademarks of their respective owners. Features and specifications are subject to change without notice. All weights and measures are approximate.
Tuner Type: FM Station Preset(s): 20 FM Audio Power Output: Amplifier: 1000W (167 x 5 at 3ohms, 1kHz, 10%THD) Impedance: 3 ohms Tuning: FM: 87.5 MHz-108.0 MHz (100 kHzstep) Speaker Type: Full Range Bass Reflex

Convenience

Timer: Yes- Sleep
Dolby Pro Logic II Decoding: Yes Surround Effect: Movie/Music Mode; Multistereo link; Speaker formation dts Decoding: Yes Dolby Digital Decoding: Yes Dolby Pro Logic Decoding: Yes A/V Synch: Yes Dolby Digital: Yes

Inputs and Outputs

Coaxial Audio Digital Input(s): 1 (Rear) Optical Audio Input(s): 1 (Rear) Antenna Terminal (FM 75 Ohm): Yes HDMI Connection Output(s): 1 (rear)- Up to 1080P Analog Audio Input(s): 1 (Rear-RCA) & 1 (Front-Mini Jack) Component Video (Y/Pb/Pr) Output(s): 1 (Rear) Composite Video Output(s): 1 (Rear) D.C.A.C. (Auto Calibration): Yes Speaker Terminal: 6 DAV Clips (Rear- 2 Front/ 2 Surround/ 1 Center/ 1 Sub) USB Port(s): 1 (Front)-See Owners Manual for devices supported
Multiple Disc Resume: Yes (10 Discs) Power Save Mode: Yes On-Screen Display: Yes

General Video

HDMI Upscaling: Yes4
Power Consumption (in Standby): less than 0.2 W Power Requirements: 120V AC, 60Hz Power Consumption (in Operation): 170W

(upto 1080p)

Speaker
Speaker System: Bass Reflex (Ported) Speaker Type: Bass Reflex (Ported) Speaker Unit: 160mm Speaker Terminal Type: DAV Speaker Clips

Specifications

General
Disc Capacity: Single disc tray Function: Tuner (FM), DVD/CD, TV/VIDEO, Audio In, USB Enclosure Type: Bass Reflex (Ported) Input Terminal: Push Type Model name: SS-TS102 Rated Impedance: 3 ohm Speaker System: 1 Way (Full Range) Speaker Unit: 1 Front Grille/Material: Fixed - Punched Metal Type: Micro Sat. Woofer Unit: 65mm Magnetically Shielded: Yes

Weights and Measurements

Dimensions (Approx.): 17" x 2.6" x 15.2" (430 x 66 x 385mm) Weight (Approx.): 9.7 lbs (4.4Kg)

General Power

Battery Type: AA / Manganese for remote (RM-ADU078) Power Save Mode: Yes
Dimmer: Yes VACS: Yes DEMO Mode: Yes Illumination Mode: Yes
Digital-to-Analog Converter: 108MHz/12bit Picture Ability: Picture Navigation and On Screen Display Sony Electronics Inc. 16530 Via Esprillo San Diego, CA 92127 1.800.222.7669 www.sony.com
Please visit the Dealer Source for current information at www.sony.com/dealersource Last Updated: 03/03/2010