SWITCHER PROCESSOR PACK

DVS-9000-C DVS9000SF-C
PRODUCTION SWITCHER PROCESSOR

DVS-9000 DVS-9000SF

BKDS-9160 BKDS-9470
BKDS-9161 BKDS-9162 BKDS-9210 MKS-8110SD MKS-8111SD HK-PSU04
OPERATION MANUAL 1st Edition

[English]

WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED.
Pour les utilisateurs au Canada (BKDS-9160/9161/9162/ 9210/9470, MKS-8110SD/8111SD, HK-PSU04 uniquement) Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada. WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. If used in USA, use the UL LISTED power cord specified below. DO NOT USE ANY OTHER POWER CORD. Plug Cap Cord Length Rating Parallel blade with ground pin (NEMA 5-15P Configuration) Type SJT, three 18 AWG wires Less than 2.5 m (8 ft 3 in) Minimum 10 A, 125 V
For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel. WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1. Use the approved Power Cord (3-core mains lead)/ Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2. Use the Power Cord (3-core mains lead)/Appliance Connector/Plug conforming to the proper ratings (Voltage, Ampere). If you have questions on the use of the above Power Cord/ Appliance Connector/Plug, please consult a qualified service personnel.
This symbol is intended to alert the user to the presence of important operrating and maintenance (servicing) instructions in the literature accompanying the appliance.
VORSICHT Um Feuergefahr und die Gefahr eines elektrischen Schlages zu vermeiden, darf das Gert weder Regen noch Feuchtigkeit ausgesetzt werden. Um einen elektrishen Schlag zu vermeiden, darf das Gehuse nicht geffnet werden. berlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. DIESES GERT MUSS GEERDET WERDEN.
(BKDS-9160/9161/9162/9210/9470, MKS-8110SD/8111SD, HK-PSU04 only) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device most accept any interference received, including interference that may cause undesired operation.
For customers in Canada (BKDS-9160/9161/9162/9210/ 9470, MKS-8110SD/8111SD, HK-PSU04 only) This Class A digital apparatus complies with Canadian ICES003.
AVERTISSEMENT Afin dviter tout risque dincendie ou dlectrocution, ne pas exposer cet appareil la pluie ou lhumidit. Afin dcarter tout risque dlectrocution, garder le coffret ferm. Ne confier lentretien de lappareil qu un personnel qualifi. CET APPAREIL DOIT TRE RELI LA TERRE.
For the customers in Europe (BKDS-9210/9160/9161/9470, MKS-8110SD/8111SD, HK-PSU04 only) This product with the CE marking complies with the EMC Directive (89/336/EEC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European standards: EN55103-1: Electromagnetic Interference (Emission) EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio). Fr Kunden in Europa (nur BKDS-9210/9160/9161/9470, MKS-8110SD/8111SD, HK-PSU04) Dieses Produkt besitzt die CE-Kennzeichnung und erfllt die EMV-Direktive (89/336/EEC) der EG-Kommission. Die Erfllung dieser Direktive bedeutet Konformitt fr die folgenden Europischen Normen: EN55103-1: Elektromagnetische Interferenz (Emission) EN55103-2: Elektromagnetische Empfindlichkeit (Immunitt) Dieses Produkt ist fr den Einsatz unter die folgende elektromagnetische Bedingung ausgelegt: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio). Pour les clients europens (BKDS-9210/9160/9161/9470, MKS-8110SD/8111SD, HK-PSU04 uniquement) Ce produit portant la marque CE est conforme la Directive sur la compatibilit lectromagntique (EMC) (89/336/CEE) mise par la Commission de la Communaut europenne. La conformit cette directive implique la conformit aux normes europennes suivantes: EN55103-1: Interfrences lectromagntiques (mission) EN55103-2: Sensibilit lectromagntique (immunit) Ce produit est prvu pour tre utilis dans lenvironnement lectromagntique suivant: E4 (environnement EMC contrl ex. studio de tlvision).

Overview

The DVS-9000-C or DVS9000SF-C Switcher Processor Pack is a high-performance, multi-function production switcher processor for use in an SDTV-format DVS-9000 video switcher system. It has a wide range of application, being usable in studios and the ENG and OB vans of largescale live production systems as well as in postproduction editing systems.
Powerful frame memory functions
Up to 222 SDTV still frames can be stored in frame memory, and up to eight frames can be called up for use simultaneously. Frames are called up instantly, making it possible to achieve animation effects. Image movement and paint functions are also possible. Still pictures from frame memory can be stored on the internal hard disk drive of the center control panel, and still pictures can be imported from and exported to PCs and other external devices.

Four-channel DME

Features

SDTV format support

This unit supports the 480i/59.94 and 576i/50 formats.
Installation of an optional DME board set provides fourchannel DME functionality. You can apply DME wipes, processed keys, and a wide variety of other DME functions.
Highly expandable system configuration
By combining option boards, you can configure the optimum system for your requirements, selecting the number of inputs and outputs and the number of M/E banks. The systems flexibility guarantees its ability to meet future expansion requirements.
Optional backup power supply
Installation of one or two optional HK-PSU04 Power Supply Units provides backup power in addition to the power supply unit (s) supplied as standard equipment. This reduces the risk of power trouble and increases the reliability of live broadcast systems.

High-performance keyers

Each M/E bank is equipped with four high-performance keyers that provide the following standard functions. Ability to apply transitions to keyers independently of the background Chroma key and color vector keys in each keyer FineKeyTM, and key borders up to 8H Color mixable matte generator available for both key fill and key borders
Overview of the DVS-9000 Components
DVS-9000 Production Switcher Processor
DVS-9000 Production Switcher Processor main unit. This is the main chassis unit of the DVS-9000 Production Switcher Processor (size EIA 8RU). It is supplied with boards for 2 M/E banks, 17 inputs, and 24 outputs as standard equipment. The following options may be installed to configure different systems.
Option Name BKDS-9160 BKDS-9161 BKDS-9210 BKDS-9470 MKS-8110SD MKS-8111SD HK-PSU04 Maximum number of installable option boards 2
Simultaneous output of four programs
Each M/E bank is able to handle four simultaneous program outputs, with the ability to apply any of the four keys to program output. This gives the system the ability to handle a wide range of operating situations, for example simultaneous transmission of four programs.

Powerful preview functions
The system supports simultaneous output of look-ahead previews (next preview) and key previews, and also transition previews.
DVS-9000SF Production Switcher Processor
DVS-9000SF Production Switcher Processor main unit. This is the main chassis unit of the DVS-9000SF Production Switcher Processor (size EIA 4RU). It is supplied with boards for 1 M/E banks, 17 inputs, and 12 outputs as standard equipment. The following options may be installed to configure different systems.
Option Name BKDS-9162 BKDS-9210 BKDS-9470 MKS-8110SD HK-PSU04 Maximum number of installable option boards 1
HK-PSU04 Power Supply Unit
A backup power supply unit. By installing one or two backup units in the DVS-9000, or one backup unit in the DVS-9000SF, you can back up the systems power supply.

BKDS-Output Board Set

A 24-output board set. This option is for the DVS-9000 only. One option set can be installed.
BKDS-Monitor Output Board
An 8-output board for monitoring input signals. This option is for the DVS-9000 only. One option board can be installed.
BKDS-Output Connector Board
A 12-output connector board. This option is for the DVS9000SF only. One option board can be installed.
BKDS-9210 Mix Effect Board
A M/E board. Depending on the configuration, up to two option boards can be installed in a DVS-9000 system. One option board can be installed in a DVS-9000SF system.

BKDS-9470 DME Board Set

A 4-channel DME option board set. One option set can be installed in either the DVS-9000 or DVS-9000SF.
MKS-8110SD 17 Input Board
A 17-input board. Up to option three boards can be installed in the DVS-9000. One option board can be installed in the DVS-9000SF.
MKS-8111SD Additional 12 Input Board
A 12-input expansion board. This option is for the DVS9000 only. One option board can be installed. When more than 68 inputs (three MKS-8110SD boards) are required, this board can be installed to provide up to 80 inputs.
Location and Function of Parts

DVS-9000 Front Panel

POWER A

POWER B

Power A, B, C, D switches and status indicator

POWER C

POWER D
POWER A, B, C and D switches and status indicators The POWER switches turn the unit on and off. The unit is powered on when the POWER switches are on the ? side, and powered off when the POWER switches are on the a side. The status indicators light in green when the unit is powered on. Depending on the systems configuration when shipped, there may be no optional HK-PSU04 Power Supply Units installed. In this case, the only available POWER switches are A and B (there are no switches C and D). The unit is not powered on until two of the POWER switches (A, B, C, and D) are turned on. With HK-PSU04 units installed, the system continues to function normally as long as any two of the power supply units are operating normally.

Caution

When installing the HK-PSU04 in your unit, be sure to contact your Sony service representative.
If a status indicator does not light when you turn a POWER switch on, there may be a fault in the power circuits. Turn the POWER switch off and contact your Sony service representative.

DVS-9000 Rear Panel

1SWITCHER REMOTE 1 to 4 connectors 2SWITCHER CTRL connector 3 EXT connector 4REF OUT connector 5SWITCHER DATA connector 6REF IN connectors 7DME EXT IN 1 to 4 connectors 8DME DATA connector 9DME CTRL connector 0 DME MONI OUT 1 to 4 connectors qaDME REMOTE connector qsDME GPI connector qdSWITCHER GPI connector qfTERMINAL connector

EXT IN MONI OUT

- AC IN

DATA CTRL REMOTE GPI

REF IN DATA CTRL REMOTE 2 REMOTE 1 GPI
REF OUT EXT REMOTE 4 REMOTE 3 TERMINAL

OUT SD

qjOUTPUTS 1 to 48 connectors qkPRIMARY INPUTS 1 to 68 connectors qlEXTEND INPUTS 69 to 80 connectors w;MONITOR OUTPUTS 49 to 56 connectors qgU terminal qh-AC IN A, B, C, D connectors
a SWITCHER REMOTE 1 to 4 connectors (D-sub 9-pin, RS-422A) Used to control the DVS-9000 AUX bus from external devices, and to operate the DVS-9000 from editing control systems such as the BVE-9100. Specify the types of connected devices on the center control panel. b SWITCHER CTRL (Switcher Control) connector (RJ-45) Connect to an Ethernet switch*. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel.
* For information about Ethernet switches that can be used in an DVS-9000 system, contact your Sony service representative. * Ethernet is a trademark of XEROX Corporation.
two connectors have a loop-through configuration. Signal input to one connector can be output from the other connector. If you will not be using the loop-through output, be sure to terminate the unused connector with the supplied 75 terminator. g DME EXT IN (Digital Multi Effects External input) 1 to 4 connectors (BNC type) (BKDS-9470) Connectors for four serial digital video signal inputs. Dedicated input for DME external video. h DME DATA (Digital Multi Effects Data) connector (RJ-45) (BKDS-9470) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices.

For more information about Ethernet switch connectors, see DVS-9000 System Configuration (page 15). For detailed information about setting up the Ethernet switch, refer to the documentation supplied with the Ethernet switch.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. i DME CTRL (Digital Multi Effects Control) connector (RJ-45) (BKDS-9470) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. c EXT (extension) connector (BNC type) Used to expand inputs by connecting devices such as an HDS-X series routing switcher. d REF OUT (reference video output) connector (BNC type) Output analog sync signals. e SWITCHER DATA connector (RJ-45) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily for exchange of various types of data (key frame effects, snapshots, etc.) and still pictures of frame memory.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. j DME MONI OUT (Digital Multi Effects Monitor Output) 1 to 4 connectors (BNC type) (BKDS-9470) Connectors for four serial digital video signal outputs. These connectors allow you to monitor any desired output signal with the DME signal (video, key, or with graphics). k DME REMOTE (Digital Multi Effects Remote) connector (D-sub 9-pin, RS-422A) (BKDS-9470) When a BKDS-9470 is installed, enables control of DME operations from remote devices. l DME GPI (Digital Multi Effects General Purpose Interface) connector (D-sub 25-pin) (BKDS-9470) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel.

When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. f REF IN (reference signal input) connectors (BNC type) If you wish to synchronize this unit to an external reference signal, input a black burst signal or analog sync signal. The
m SWITCHER GPI (Switcher General Purpose Interface) connector (D-sub 25-pin) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. n TERMINAL connector (D-sub 9-pin, RS-232C) This connetor is used for factory adjustments. o U (signal ground) terminal Connect to the system ground. p - AC IN (AC power input) A, B, C, D connectors (3-pin) Connect to 100 to 240 V AC power supply with the optional AC power cords. Depending on the systems configuration when shipped, there may be no optional HK-PSU04 Power Supply Units installed. In that case, the AC IN C and D connectors is not used.
t MONITOR OUTPUTS 49 to 56 connectors (BNC type) (BKDS-9161) Use these connectors as outputs for primary input monitors or as auxiliary outputs for external devices. These connectors are effective if you wish to output primary inputs with as little delay as possible.
For information about installing an HK-PSU04, contact your Sony service representative. q OUTPUTS 1 to 48 connectors (BNC type) (BKDS-9160) These connectors output serial digital signals. They can be freely assigned to program output, preview output, AUX output and so on. There are two BNC connectors for the lower numbers on each slot (1 to 4, 13 to 16, 25 to 28, 37 to 40) and one BNC connector for the upper numbers (5 to 12, 17 to 24, 29 to 36, 41 to 48). Make output assignments using the center control panel of the DVS-9000 system. The number of connectors varies depending on the number of BKDS-9160 sets installed. Refer to the Users Guide for information about signals that may be assigned. r PRIMARY INPUTS 1 to 68 connectors (BNC type) (MKS-8110SD) These connector accept up to 68 serial digital video signal inputs. The number of connectors varies depending on the number of MKS-8110SD boards installed. s EXTEND INPUTS 69 to 80 connectors (BNC type) (MKS-8111SD) These connectors accept up to 12 expansion serial digital video signal inputs. Use these connectors when 69 or more inputs are required.

DVS-9000SF Front Panel

Power A, B switches and status indicator
Power A, B switches and status indicators
The POWER switches turn the unit on and off. The unit is powered on when the POWER switches are on the ? side, and powered off when the POWER switches are on the a side. The status indicators light in green when the unit is powered on. Depending on the systems configuration when shipped, there may be no optional HK-PSU04 Power Supply Unit installed. In this case, the only available POWER switch is A (there is no switch B). The unit is powered on when either of the two POWER switches (A or B) is turned on. With an HK-PSU04 unit installed, the system continues to function normally as long as either of the two power supply units is operating normally.

DVS-9000SF Rear Panel

1EXT connector 2REF OUT connector 3SWITCHER CTRL connector 4SWITCHER DATA connector 5REF IN connectors 6DME EXT IN 1 to 4 connectors 7DME DATA connector 8DME CTRL connector 9 DME MONI OUT 1 to 4 connectors
0DME REMOTE connector qaDME GPI connector qsSWITCHER GPI connector qdSWITCHER REMOTE 1 to 4 connectors qfTERMINAL connector

REF OUT

REMOTE 4

REMOTE 3

TERMINAL
qjPRIMARY INPUTS 1 to 34 connectors qkOUTPUTS 1 to 24 connectors
qgU terminal qh-AC IN A, B connectors
a EXT (extension) connector (BNC type) Used to expand inputs by connecting devices such as an HDS-X series routing switcher. b REF OUT (reference video output) connector (BNC type) Output analog sync signals. c SWITCHER CTRL (Switcher Control) connector (RJ-45) Connect to an Ethernet switch*. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel.
* For information about Ethernet switches that can be used in an DVS-9000 system, contact your Sony service representative.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage.
d SWITCHER DATA connector (RJ-45) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily for exchange of various types of data (key frame effects, snapshots, etc.) and still pictures of frame memory.

i DME MONI OUT (Digital Multi Effects Monitor Output) 1 to 4 connectors (BNC type) (BKDS-9470) Connectors for four serial digital video signal outputs. These connectors allow you to monitor any desired output signal with the DME signal (video, key, or with graphics). j DME REMOTE (Digital Multi Effects Remote) connector (D-sub 9-pin, RS-422A) (BKDS-9470) When a BKDS-9470 DME Board Set is installed, use this connector to control the unit from an external device. k DME GPI (Digital Multi Effects General Purpose Interface) connector (D-sub 25-pin) (BKDS-9470) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. l SWITCHER GPI (Switcher General Puropose Interface) connector (D-sub 25-pin) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. m SWITCHER REMOTE 1 to 4 connectors (D-sub 9-pin, RS-422A) Used to control the DVS-9000SF AUX bus from external devices, and to operate the DVS-9000SF from editing control systems such as the BVE-9100. Specify the types of connected devices on the center control panel. n TERMINAL connector (D-sub 9-pin, RS-232C) This connetor is used for factory adjustments. o U (signal ground) terminal Connect to the system ground. p -AC IN (AC power input) A, B connectors (3-pin) Connect to 100 to 240 V AC power supply with the optional AC power cords. Depending on the systems configuration when shipped, there may be no optional HK-PSU04 Power Supply Unit installed. In that case, the AC IN B connector is not used.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. e REF IN (reference signal input) connectors (BNC type) If you wish to synchronize this unit to an external reference signal, input a black burst signal or analog sync signal. The two connectors have a loop-through configuration. Signal input to one connector can be output from the other connector. If you will not be using the loop-through output, be sure to terminate the unused connector with the supplied 75 terminator. f DME EXT IN (Digital Multi Effects External input) 1 to 4 connectors (BNC type) (BKDS-9470) Connectors for four serial digital video signal inputs. Dedicated input for DME external video. g DME DATA (Digital Multi Effects Data) connector (RJ-45) (BKDS-9470) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. h DME CTRL (Digital Multi Effects Control) connector (RJ-45) (BKDS-9470) Connect to an Ethernet switch. The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel.

Video input signal Video output signal AC power supply
Power Supply Unit Status Indicators
The power supply unit status indicators show the status of the power supply unit during operation and when the unit is powered on. Whenever a power error is detected, it is reflected immediately by the indicator.
Meaning of status indicator displays Indicator Status color Green Red Lit Lit Not lit Description Operating normally Steps to take
Power supply unit fan Exchange the fault fan unit Power supply unit fault Exchange the power unit
When the unit is powered on, the status indicators may light momentarily in red and a whining sound may be heard. This is not a malfunction.When some of the power supply units are off and some are on, the status indicators of the units which are off may light in red. This is not a malfunction. Power all of the installed power supply units on.

Specifications

The following specifications show the reference performance for this unit and individual option boards/ modules. Design and specifications are subject to change without notice.
Complies with RS-232C standard Data transfer rate: 9600 bps BNC type, 75 S-BUS data transfer rate: 312/1250 Kbps
Reference input and output
REF IN BNC type, 75, with loop-through output Analog black burst/analog sync BNC type, 75 Analog sync Signal level 300 mV 10% Phase variation range 90H to +90H

General

Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 8.5 A, 240 V: 4.2A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Operating temperature 5C to 40C (41F to 104F) Performance guaranteed temperature 10C to 35C (50F to 95F) Storage temperature 20C to +60C (4F to +140F) Operating humidity 10% to 90% Dimensions (w/h/d, excluding projections) 482354520 mm (1914201/2 inches) Mass Approx. 43 kg (9 lb 7 oz)

Video input

Inputs 17 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent)

Video output

Outputs 24 (BNC type): 1 to 4 and 13 to 16, each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps

AC input

AC IN A, B, C, D 3-pin AC connector
Accessories supplied Control connectors
CTRL RJ-45 Complies with 100Base-TX standard DATA RJ-45 Complies with 100Base-TX standard REMOTE 1, 2, 3, 4 D-sub 9-pin, female Comply with RS-422A standard Data transfer rate: 38.4 Kbps GPI D-sub 25-pin, female TTL inputs: 8 Relay contact outputs: 4 (30V AC/DC, 0.1A) Open collector outputs: 4 TERMINAL D-sub 9-pin, female 75 terminator (1) Bracket (4) Support angle (2) Screw (+B410) (8) Screw (+PSW 410) (8) Operation Manual (1) Installation Manual (1)

Accessories not supplied

AC power cord (for USA and Canada only) (125 V 10 A 2.4 m (8 ft)) (Part No.: 1-557-377-11) AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft)) (Part No.: 1-782-929-21)
Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 5.4 A, 240 V: 2.5 A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Operating temperature 5C to 40C (41F to 104F) Performance guaranteed temperature 10C to 35C (50F to 95F) Storage temperature 20C to +60C (4F to +140F) Operating humidity 10% to 90% Dimensions (w/h/d, excluding projections) 482177520 mm (197201/2 inches) Mass Approx. 25 kg (5 lb 8 oz)
Analog sync Signal level 300 mV 10% Phase variation range 90H to +90H
Outputs 12 (BNC type): 1 to 4, each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps
AC IN A, B 3-pin AC connector

Accessories supplied

75 terminator (1) Bracket (4) Support angle (2) Screw (+B410) (8) Screw (+PSW 410) (8) Operation Manual (1) Installation Manual (1)

Control connectors

CTRL RJ-45 Complies with 100Base-TX standard DATA RJ-45 Complies with 100Base-TX standard REMOTE 1, 2, 3, 4 D-sub 9-pin, female Comply with RS-422A standard Data transfer rate: 38.4 Kbps GPI D-sub 25-pin, female TTL inputs: 8 Relay contact outputs: 4 (30V AC/DC, 0.1A) Open collector outputs: 4 TERMINAL D-sub 9-pin, female Complies with RS-232C standard Data transfer rate: 9600 bps EXT BNC type, 75 S-BUS data transfer rate: 312/1250 Kbps
Power requirements 12 V DC Power consumption Max. 50 W Dimensions (w/h) OUT board: 317380 mm (121/215 inches)
REF IN BNC type, 75, with loop-through output Analog black burst/analog sync BNC type, 75
CN board: 27494 mm (107/833/4 inches) (using 2 boards) Approx. 2 kg (4 lb 6 oz)

Output

Outputs 12 (BNC type), 1 to 4, each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 Vp-p 10% Signal transfer rate 270 Mbps
Outputs 24 (BNC type), 1 to 4 and 13 to 16, each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 Vp-p 10% Signal transfer rate 270 Mbps
Operation and Installation Guide (1) (supplied only when product is purchased separately)
BKDS-9210 Mix/Effect Board
Power requirements 12 V DC Power consumption Max. 80 W Dimensions (w/d, excluding projections) 317380 mm (121/215 inches) Mass Approx. 2 kg (4 lb 6 oz) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)
BKDS-9161 Monitor Output Board
Power requirements 12 V DC Power consumption Max. 10 W Dimensions (w/d, excluding projections) 27494 mm (107/833/4 inches) Mass Approx. 1 kg (2 lb 3 oz)
Power requirements 12 V DC Power consumption Max. 100 W Dimensions (w/h) DVP board: 317380 mm (121/215 inches) CA board: 317380 mm (121/215 inches) CN board: 27494 mm (107/833/4 inches) (When used with two boards) Mass Approx. 4 kg (8 lb 13 oz)
Outputs 8 (BNC type), each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 Vp-p 10% Signal transfer rate 270 Mbps
Power requirements 12 V DC Power consumption Max. 5 W Dimensions (w/d, excluding projections) 27494 mm (107/833/4 inches) Mass Approx. 1 kg (2 lb 3 oz)
Remote Control connectors
CTRL DATA REMOTE RJ-45 Complies with 100Base-TX standard RJ-45 Complies with 100Base-TX standard D-sub 9-pin, female Complies with RS-422A standard Data transfer rate: 38.4 Kbps D-sub 25-pin, female TTL inputs: 8
Relay contact outputs: 4 (30V AC/DC, 0.1A) Open collector outputs: 4
Power requirements 12 V DC Power consumption Max. 10 W Dimensions (w/h) 27494 mm (107/833/4 inches) Mass Approx. 1 kg (2 lb 3 oz)
Inputs 4 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent)
Outputs 4 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps
Inputs 12 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent)
Power requirements 100 to 240 V AC, 50/60 Hz Power consumption 100 V: 10 A, 240 V: 5 A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Output power 12 V DC 0.5V Secondary power supply Max. 60 A Dimensions (w/h/d) 9483396 mm (33/433/8155/8 inches) Mass Approx. 3 kg (6 lb 9 oz) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matriel contenu dans ce manuel consiste en informations qui sont la proprit de Sony Corporation et sont destines exclusivement lusage des acqureurs de lquipement dcrit dans ce manuel. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des oprations ou entretiens de lquipement moins dune permission crite de Sony Corporation. Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind, und ausschlielich zum Gebrauch durch den Kufer der in dieser Anleitung beschriebenen Ausrstung bestimmt sind. Die Sony Corporation untersagt ausdrcklich die Vervielfltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben fr irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrstung ohne ausdrckliche schriftliche Erlaubnis der Sony Corporation.

Sony Corporation

B & P Company
DVS-9000 (WW) 3-690-433-01 (1)
Printed on recycled paper
Printed in Japan 2002.07.13 2002