4 Time data/menu display section (see page 2-7)
2 CHANNEL CONDITION indicator (see page 2-6) 1 Audio control section (see page 2-4) 3 Menu control buttons (see page 2-6)
5 MULTI CONTROL knob and SHIFT indicator (see page 2-8) 6 RESET button (see page 2-8)
7 Search control section (see page 2-8) 8 REC INHI indicator (see page 2-10) 9 Tape transport control section (see page 2-10)
qa ALARM indicator and KEY INHI indicator (see page 2-11)
q; Editing mode setting section (see page 2-11)
qs PLAYER button and RECORDER button (see page 2-12)
qd Editing control section (see page 2-12) qf Shot mark section (see page 2-13)

1 Audio control section

1 Audio selection function selector buttons 2 DISPLAY FULL/FINE button 3 Audio setting display section 4 Audio signal selection buttons
MIXING (mixing setting mode) button: Pressing this button puts the unit into mixing setting mode. In the audio setting display section, the MIX indicator flashes. In this state, you can use the audio signal selection buttons to specify which input channel signal will be recorded on which audio track on the tape. Pressing this button again takes the unit out of mixing setting mode and puts it into monitor signal selection mode.
On how to operate in input signal selection mode, mixing setting mode, and monitor signal selection mode, see the descriptions of the audio signal selection buttons on page 2-5.
6 PB controls 5 REC controls
In the audio control section, you can select and display input and output signals for audio channels. 1 Audio selection function selector buttons INPUT (input signal selection mode) button: Pressing this button puts the unit into input signal selection mode. In the audio setting display section, indicators flash to indicate the currently selected signal for each channel (SDI, AES/EBU, or ANA). In this state, you can use the audio signal selection buttons to select the signal to input to each channel. You can select the following signals for audio input channels 1 to 4, respectively. For input channel 1: SDI-1, SDI-5, AES/EBU-1, or ANALOG-1 For input channel 2: SDI-2, SDI-6, AES/EBU-2, or ANALOG-2 For input channel 3: SDI-3, SDI-7, AES/EBU-3, or ANALOG-3 For input channel 4: SDI-4, SDI-8, AES/EBU-4, or ANALOG-4 Pressing this button again takes the unit out of input signal selection mode and puts it into monitor signal selection mode.

1 AUDIO INPUT (AES/EBU) connectors (BNC type) Input up to two sets (4 channels: channels 1/2 and 3/4) of AES/EBU format digital audio signals. 2 AUDIO OUTPUT (AES/EBU) connectors (BNC type) These connectors output up to four sets (8 channels: channels 1/2, 3/4, 5/6 and 7/8) of AES/EBU format digital audio signals. Note that if your unit is a DVW2000/2000P, AES/EBU digital audio outputs are limited to two sets (4 channels: channels 1/2 and 3/4).
4 Digital signal input/output section

5 Power supply section

SDI INPUT
1 AC IN connector 1 SDI INPUT connectors

2 Ground terminal

OUTPUT 1
1 AC IN connector Use a power cord to connect this to an AC outlet.

2 SDI OUTPUT connectors

3(SUPER)
2 Ground terminal Connect this to ground.
6 External device connectors
1 SDI (Serial Digital Interface) INPUT connectors (BNC type) Input D1 format digital video/audio signals. Of the two connectors, the upper one is for input, and the lower one is for an active-through connection. 2 SDI (Serial Digital Interface) OUTPUT connectors (BNC type) These connectors output D1 format digital video/audio signals. When the setting of F4 (CHARA) in function menu page 4 is ON, connector 3 (SUPER) outputs a signal with superimposed time code, menu settings, alarm messages, and other text information.
REMOTE 2 PARALLEL I/O(50P)

REMOTE 1-IN(9P)

CONTROL PANEL
1 REMOTE 2 PARALLEL I/O(50P) connector 2 CONTROL PANEL connector

REMOTE 1-OUT(9P)

VIDEO CONTROL
3 VIDEO CONTROL connector

RS232C

4 OPTION connector

(OPTION)

5 REMOTE 1-IN(9P) connector 6 REMOTE 1-OUT(9P) connector 7 RS-232C connector
1 REMOTE 2 PARALLEL I/O(50P) connector (D-sub 50-pin) Connect remote control signals from an external device.
2 CONTROL PANEL connector (round type, 10pin) In addition to the lower control panel, a similar control panel can be connected to this unit. To connect such a second control panel, use this connector. When two control panels are connected, use the PANEL SELECT switch on the switch panel (see page 2-14) to specify which control panel will control this unit. 3 VIDEO CONTROL connector (D-sub 15-pin) For remote control of the internal digital video processor, connect an optional BVR-50/50P Remote Control Unit. Always power off this unit before connecting the remote control unit. 4 OPTION connector (D-sub 9-pin) Not used. 5 REMOTE 1-IN(9P) connector (D-sub 9-pin) When using this unit together with another DVWM2000/M2000P/2000/2000P or an MPEG IMX, D-1, D-2, or Betacam VTR, and a BVE-series BVE-900/ 910/2000/9000/9000P/9100/9100P or other editor, connect the optional 9-pin remote control cable from the other unit to this connector. Depending on the setting of setup menu item 211, you can use this connector alone, or in a loop-through configuration with the REMOTE 1-OUT(9P) connector. 6 REMOTE 1-OUT(9P) connector (D-sub 9-pin) This provides the loop-through output for remote control signals from the REMOTE 1-IN(9P) connector. Depending on the setting of setup menu item 211, you can use this connector alone, or in a loop-through configuration with the REMOTE 1-IN(9P) connector. 7 RS-232C connector (D-sub 9-pin) Use this for monitoring and diagnosis of the state of this unit from an external computer, using ISR (Interactive Status Reporting).

4-2-3 Dynamic Motion Control (DMC) Playback
DMC playback allows you to vary the playback speed for a certain section of a tape, in variable speed mode (from 1 to +3 times normal speed for digital Betacam playback, from 1 to +3 times normal speed for MPEG IMX playback, from 1 to +2 times normal speed for Betacam SX playback, or from 1 to +3 times normal speed for analog Betacam playback), and store the varying speed in memory for later playback at the same varying speed.
On-air start point Preroll point Waiting for the on-air cue before starting DMC playback Stop
For example, during a live broadcast of a sporting event you can set the start and end points of highlights while recording, and then provide immediate DMC playback of those highlights. During DMC playback the tape moves as shown in the following figure.
Speed variation start point
Speed variation end point

On-air end point

Press the REVIEW button. Normal speed playback
Press the REVIEW button again at the on-air cue.

DMC playback

Normal speed playback Stop
Starting DMC playback immediately after preroll
Press the PREVIEW button. Normal speed playback

Normal speed playback

Storing a varying playback speed in memory
To store the playback speed for DMC playback, use the following procedure.
Press the DMC EDIT button, turning it on. Either while playing back the recorded tape, or during recording, press the ENTRY button and one of the following buttons simultaneously, to set the start and end points. On-air start point: AUDIO IN button Speed variation start point: IN button Speed variation end point: OUT button On-air end point: AUDIO OUT button Each press turns the corresponding button on.
Make sure that the TSO PLAY of setup menu item 111 is set to DIS beforehand.
Press the search dial or the SHUTTLE button or VAR button to enter shuttle/variable speed mode. The SHUTTLE/VAR indicator lights.
Holding down the DMC EDIT button, turn the search dial, to set the initial speed at the playback start point. The speed you set appears in the speed indication area. During this period the tape does not move. When the initial speed setting is complete, release the DMC EDIT button.

For details of deleting edit points, see the section Deleting an edit point (page 5-6).
Setting split edit points
In split editing, you can set the edit points for audio and video independently. Set the audio edit points with the AUDIO IN/OUT buttons, and the video edit points with the IN/OUT buttons. Note that split editing is only possible when the recording mode is insert editing.
During split editing, if you set six or more edit points for the recorder and player, the DELETE button starts to flash, to indicate that such a setup is impossible. Delete all unnecessary edit points, using the DELETE button.
For details of how to delete edit points, see the section Deleting an edit point (page 5-6).
Automatic setting of edit points in split editing Split editing requires a total of eight edit points: four video edit points (player IN and OUT and recorder IN and OUT) and four audio edit points (player audio IN and OUT and recorder audio IN and OUT). However, as soon as you set five points, the system automatically calculates and sets the remaining three points. Specifically, once you have set three of the four video edit points and two audio edit points, the remaining three edit points are set automatically, regardless of whether these points are for the recorder or player. In the figure below, the edit points shown within boxes are already set. The other edit points (recorder audio OUT point, and player audio IN and video OUT points) are set automatically. Note that, regardless of whether it was set manually or automatically, any edit point can be deleted or corrected later.
Press the appropriate INSERT button (VIDEO, CH1 to CH4, CUE, or TC). The IN/OUT button flash.
Press the RECORDER or PLAYER button to select the VTR for which edit points are to be set. The button you have pressed lights.
To find the edit point, rotate the search dial in jog or shuttle mode.
For details of jog/shuttle mode playback, see the sections Playback in jog mode and Playback in shuttle mode (page 4-8).

Audio IN point

IN point Audio OUT point

OUT point

Recorder

Player

Press the ENTRY button together with one of the IN, OUT, AUDIO IN, and AUDIO OUT buttons, to set the edit point. Once an edit point is set, the corresponding button changes from flashing to continuously lit.

The following figure illustrates this.
Using a single monitor for video and audio on both player and recorder
For efficient editing if only one monitor is available, use the following method.
OUT button ENTRY button REVIEW button AUTO EDIT button PREVIEW button
Connect the monitor to the recorder. In the basic setup menu, set item 008 to AUTO. Press the PLAYER button on the recorder. This forces the recorder to E-E mode, in which the player video and audio signals are output to the monitor.
To change the OUT point after starting automatic editing operation After starting the automatic editing operation, to end the operation before the preset OUT point, hold down the ENTRY button and press the OUT button. The position where you pressed the button becomes the OUT point, and editing ends. To abandon automatic editing Press the STOP button. The automatic editing operation is abandoned. At the same time, the PREVIEW button and AUTO EDIT button start flashing, and the state before the editing was started is restored. In this case, the IN and OUT points already set are preserved so that you can carry out a preview or automatic editing operation again by pressing the PREVIEW button or AUTO EDIT button. Reviewing the editing results After carrying out an editing operation, you can carry out a review, to check the editing results on the monitor. To carry out a review, after carrying out the edit, and before you set any new edit points or make other settings, press the REVIEW button. The REVIEW button lights, and the review is carried out. At the end of the review the REVIEW button goes off, and the tape returns to the OUT point.
In insert editing to tape, it is necessary for audio, video, and CTL signals to be recorded in advance throughout the insert editing section on the tape. If you execute an insert edit over a section where these signals are not present, noise or breakup can occur in the audio and video when that section is played back.
Starting automatic editing
When you have set the edit points, press the flashing AUTO EDIT button. The AUTO EDIT button changes from flashing to continuously lit, and the automatic editing operation begins. At the end of the editing operation, the AUTO EDIT button goes off.
After automatic editing, to adjust the edit points and reexecute the edit Hold down the DELETE button and press the ENTRY button to recall the edit points. After adjusting the edit points, press the AUTO EDIT button to carry out the edit again.
For details of how to adjust edit points, see Section 5-1-5 Modifying and Deleting Edit Points (page 5-6).

5-2 DMC Editing

By controlling the player playback speed from the recorder you can achieve variable speed editing.
5-2-1 Overview of DMC Editing
Conditions for DMC editing DMC editing can be used for insert or assemble editing, but not for audio split editing. Tape movement during DMC editing The following figure illustrates how the tapes move on the player and recorder during DMC editing.

For details about setup menu item 134, see Section 12-4 Items in the Extended Setup Menu (page 12-8).

Undo check mode

Chapter 7

Tele-File

7-3 Tele-File Menu

7-3-1 Clip Data Display

Shown below are examples of the default menu displays in the menu display section and the monitor display.
Menu display section Tele-File menu indicator Data type indicator Setting display area
For more information about how to display menus on the monitor, see the section To display menus on the monitor (page 12-2).
TEL Cue E-F ATTRIB SELECT HOME F1 F2 F3 F4

UNDO WR/EXT

Menu items (functions) Title Number of selected clip
Monitor display Final data recording date Data type Clip No. 0001 Clip No. 0002 Clip No. 0003
TELE-FILE : TEST 01 2001/07/21 No. 0001 Cue Point WP Mark *00:00:02:10 ON KEEP 00:00:31:10 00:00:57:10

48% R @

Remaining memory percentage a)
a) The Tele-File memory always contains the attribute data so that this indication never shows 100%.
Tele-File menu indicator Indicates that the menu display section is currently displaying the Tele-File menu. Data type indicator Indicates the type of data selected with the clip data display mode. There are the following types.
Cue: Cue point Protct: Write protected Mark: Mark R-Strt: Recording start point IN: IN point OUT: OUT point Take: Take number Cut: Cut number Scene: Scene number Comnt: Comment
Setting display area Displays the setting of the currently selected data type, and a cursor (* or >). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected. >: Indicates that the mode is clip data modify mode or attribute data display/modify mode, and prompts for data entry or modification.
Menu items (functions) Display menu items (functions). These are common for all of the data items in clip data display mode. The function assignments for each item are as follows.
Clip data display mode menu items Item name F1 (ATTRIB) Function Selects attribute data display/modify mode.
For details about attribute data display/modify mode, see Section 7-3-5 Displaying and Modifying Attribute Data (page 7-11).
F2 (SELECT) Selects a data modification mode for the data selected in the clip. The cursor changes from * to >. Note In the following cases, the SELECT item does not appear, and it is not possible to select a data modification mode. When setup menu item 133 is set to REMOTE When the memory label itself is write protected

Item number Item name 023 LOCAL KEY MAP
Settings When MAP is selected in menu item 006, the buttons that can be operated on the control panel of this unit when it is being controlled by remote control from another device can be selected from the following sub-items. The settings of each sub-item are as follows. DIS : Do not function. ENA: Function. Select whether the STOP button functions. Select whether the PLAY button functions. Select whether the REC and EDIT buttons function. Select whether the STANDBY button functions. Select whether the EJECT button functions. Select whether the JOG button functions. Select whether the SHUTTLE button functions. Select whether the VAR button functions. Select whether the F FWD and REW buttons function. Select whether the PREROLL button functions. Select whether the F1 to F6 buttons function. Select whether the audio signal buttons function. Select whether the EDIT PRESET button functions. Select whether the ENTRY, IN, OUT, AUDIO IN, AUDIO OUT, TRIM+, TRIM, GS-MARK, GS-LIST, DELETE, and DMC EDIT buttons function. Select whether or not to set the Stored Ownership UMID item. off : Do not set. on: Set. To set Stored Ownership, display this item in the menu display section, and press the F5 (SET) button to move to the Stored Ownership setting screen.
Sub-item STOP PLAY REC/EDIT STANDBY EJECT JOG SHUTTLE VAR FF/REW PREROLL F-KEY AUDIO/MONITOR EDIT PRESET OTHERS
AUTO/PRE/REVIEW Select whether the AUTO EDIT, PREVIEW, REVIEW buttons function.

STORED OWNERSHIP

For details, see the section To set Stored Ownership (page 8-2).
B01 B02 B03 B11 B12 B13 B20 RECALL BANK 1 RECALL BANK 2 RECALL BANK 3 SAVE BANK 1 SAVE BANK 2 SAVE BANK 3 RESET SETUP Set to ON to recall menu settings from menu bank 1. Set to ON to recall menu settings from menu bank 2. Set to ON to recall menu settings from menu bank 3. Set to ON to save current active menu settings to menu bank 1. Set to ON to save current active menu settings to menu bank 2. Set to ON to save current active menu settings to menu bank 3. Set this item to ON to return the current menu settings to the factory defaults. Set it to bank-4 to use the contents of menu bank 4 as the current menu settings.
12-4 Items in the Extended Extended 12-4 Items in the Setup Menu
The extended setup menu contains the following items.

Setup Menu

Menu items in the range 100 to 199, relating to the control panels Item number Item name 101 SELECTION FOR SEARCH DIAL ENABLE Settings Select how the unit enters the search mode. DIAL : Turning the search dial switches to search mode at all times except during recording/editing. KEY: One of the JOG, SHUTTLE, and VAR buttons must be pressed to switch to search mode. Select the fast forward and rewind tape speed and also search mode speed during tape playback. MAX : Perform fast forward, rewind, and search mode playback at the maximum speeds. MX/24: Perform fast forward and rewind at the maximum speeds, and search mode playback at up to 24 times normal speed. 24: Perform fast forward and rewind at 24 times normal speed, and search mode playback at up to 24 times normal speed. Maximum fast forward, rewind, and search mode speeds Analog cassette: 35 times (525-line mode) or 42 times (625-line mode) normal speed. Betacam SX/MPEG IMX cassettes: 60 times normal speed (525-line mode) or 78 times (625-line mode) Digital Betacam cassette: 50 times normal speed 103 AUDIO SELECTED LINE OUT (DVW-M2000/ M2000P only) Select the output signal to the MONITOR OUTPUT connectors during playback of analog Betacam-format tape. MANU : Output the signals selected by the audio signal selection buttons on the lower control panel. AUTO1: Output stereo, using the AFM channels (3 and 4) for playback from metal tape, and the LNG channels (1 and 2) for playback from oxide tape. AUTO2: Output the signals selected by the audio signal selection buttons on the lower control panel, but during variable speed playback, if AFM is selected, automatically switch to LNG. Select the length of time for which audio muting occurs when the unit switches to playback either from stopped or from still playback in the search mode. OFF : Set the audio muting time to zero (i.e. no muting). 0.1S. 1.0S: Set the audio muting time from 0.1 second to 1.0 second, in 0.1second increments. Select whether or not to display a warning when the video/audio reference signal selected by the function menu item OUTREF, is not supplied or is out of phase with the input video signal. OFF: No warning. ON : Flash the STOP button as a warning. Select the capstan servo lock mode. PANEL : The capstan servo lock mode is determined by the function menu item CAPSTN. 2F: The capstan servo locks every two fields regardless of the setting of the function menu item CAPSTN. 4F: The capstan servo locks every four fields regardless of the setting of the function menu item CAPSTN. 8F (for DVW-M2000P/2000P): The capstan servo locks every eight fields regardless of the setting of the function menu item CAPSTN.

PREREAD SELECT

DIGITAL AUDIO PB PROCESS ON EDIT POINT AUTOMATIC IN ENTRY AFTER AUTO EDIT

EE REFERENCE CONTROL

EDIT PRESET INHIBIT IN Specify which buttons are disabled in the editing mode setting section on the lower control panel. KEY PANEL CONTROL off : Disable all buttons. TC: Disable the TC button.
Item number Item name 401 FUNCTION MODE AFTER CUEUP
Menu items in the range 400 to 499, relating to preroll Settings Select the state that the unit goes into after a cuing-up operation. STOP : Stop (the stop mode) STILL: Still playback (in search mode) Note When controlling this unit from an editor with the standard constants set, select STOP.
TIME REFERENCE FOR PREROLL
When prerolling a tape with time code discontinuities, select whether or not to use CTL pulses to count time code from before a discontinuity. CTL : Use CTL pulses to count time code. TC: Do not use CTL pulses to count time code. Select whether or not the edit IN point is automatically set by pressing the PREROLL button, when the IN point is not set before starting preroll. DIS : IN point is not set automatically. ENA: IN point is set automatically. Select the tape transport mode when cuing. This setting is valid only when the function menu item CTL/TC is set to CTL. CAP. : During cuing up, the tape transport is in the pinch ON state (maximum tape speed 10 times normal). REEL : During cuing up, the tape transport is in the pinch OFF state. As the tape approaches the cue up point and the tape speed drops, the tape transport switches to the pinch ON state.a) To give priority to editing accuracy, select CAP.
AUTOMATIC PREROLL REFERENCE ENTRY

CUEUP BY CTL

a) When controlled from an editor (BVE-2000/9100 etc.), selecting REEL allows high-speed cuing up.
Menu items in the range 500 to 599, relating to tape protection Settings Select the time delay from the tape transport stopping (either the stop mode or the still playback mode in search mode) until the unit automatically switches to the tape protection mode, in order to protect the video heads and the tape. 0.5S. 8M. 30M: Set the value in the range 0.5 seconds to 30 minutes. Select the operation of the protection mode to protect the video heads and tape when in the still playback mode in search mode (jog/shuttle). STEP : Step forward at 1/30 normal speed every 2 seconds. STDBY: Switch to Standby OFF mode (the unit not on standby). T.REL: Switch to tension release mode (the tape tension slackened). Select the operation of the protection mode to protect the video heads and tape when stopped (the stop mode). STDBY : Switch to Standby OFF mode (the unit not on standby). T.REL: Switch to tension release mode (the tape tension slackened). Select whether the drum rotates in Standby OFF mode. OFF : Drum does not rotate. ON: Drum rotates. Select the tape tension state in the still playback mode. NORM : Normal tape tension is maintained during still playback mode, ready for playback. LOOSE: Reduce the tape tension further from the NORM setting. (Select LOOSE when the unit is on standby for a long period of still playback, for example, in a library management system (LMS).) Note When LOOSE is selected, playback cannot be guaranteed.

Menu items in the range 700 to 799, relating to video control (Continued) (Items 715 to 721: Settings for controlling the video processing system according to the menu settings) Item number Item name Settings

717 718

VIDEO GAIN CONTROL CHROMA GAIN CONTROL CHROMA PHASE CONTROL SETUP LEVEL (DVWM2000/2000)/BLACK LEVEL (DVW-M2000P/ 2000P) SYSTEM PHASE SYNC SYSTEM PHASE SC Y/C DELAY (DVWM2000/M2000P only)
Adjust the video output level. 2048 to 0 to +848 Adjust the chroma output level. 2048 to 0 to +848 Adjust the chroma phase. 128 to 0 to +127 Adjust the setup level (black level). 272 to 0 to +272
Adjust the output signal sync phase. 128 to 0 to +127 Adjust the output signal subcarrier phase. 0 to 1023 For playback from an analog Betacam cassette, adjust the Y/C delay. 2048 to 0 to +2047
When you make settings for items 715 to 721, set the function menu item V.PROC to MENU. When it is set to MENU, all controls for video output processing on the control panel are disabled.
Item number Item name 723 INPUT VIDEO BLANK Sub-Item 0 ALL LINE Settings Switch blanking on or off for individual lines in the vertical blanking interval of an input video signal. The Y/C signal and odd/even fields are blanked simultaneously. A signal with blanking carried out according to this setting is recorded. - - - : Specify the blanking for each line separately. BLANK: Regardless of the setting of other sub-items, blank all lines which can be specified in this menu item. THROU: Regardless of the setting of other sub-items, switch off blanking for all lines which can be specified in this menu item. Specify blanking for lines 12 to 20. BLANK: Carry out blanking. THROU : Switch off blanking.
DVW-M2000/ 12. DVWM2000P/ 2000P

LINE 12. LINE 20

9. 22 LINE 9. LINE 22 Specify blanking for lines 9 to 22. BLANK: Carry out blanking. THROU : Switch off blanking.
Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings 726 H BLANKING WIDTH Select the horizontal blanking width of the video output signal. NAROW : Digital blanking (narrow) WIDE: Analog blanking (wide) When WIDE is selected, the horizontal blanking width complies with RS170A, and normally the blanking is widened and the image becomes narrower. It is recommended to select NAROW at the editing stage, then later, for broadcast transmission to select WIDE, to output a signal conforming to the standard. Note, however, that NAROW has to be always selected for SDI signals. Set the output phase for the video playback signal when any of the ASSEMBLE, VIDEO, AUDIO CH1 to CH4, CUE, and TC buttons is lit. INT : The video playback signal output phase is the same as the output phase in E-E mode. Use this setting when editing with a single VTR, or when previewing while watching the VTR output signal. EXT: The video playback signal output phase is the same as the phase of an input video signal or external reference signal. Note Whichever setting is used, the correct editing results will be obtained. When, however, you are using an external switcher to switch the video output signal from this unit for the purposes of preview, select EXT. This will prevent any image shifts at editing IN and OUT points. OUTPUT SCH PHASE C.PHASE TYPE Set the subcarrier H phase. 2048 to 0 to +2047 Select the PAL chroma phase type. (DVW-M2000P/2000P) HUE : Vary the hue. L.ALT: Vary the SC phase of composite output.

When carrying out head cleaning without using the automatic cleaning function, be sure to eject the cleaning cassette after use in order not to damage the heads. You cannot use the BCT-5CLN cleaning cassette.

Chapter 14

Maintenance and Inspection
14-5 Regular Checks 14-3 Error Messages
This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor. If an error message appears, contact your Sony service representative.

Error message displays

To display error messages and codes superimposed on the monitor, set the CHARA in function menu page 4 to ON. Some error messages have no associated error codes. In this case, they appear over the time data area. Error messages with error codes are saved in nonvolatile memory as an error log. In some cases the error message is slightly different on the monitor and in the time data area.
Indications in the time data display
If a problem is detected, the ALARM indicator in the lower control panel lights, and an error message and error code appear in time data display area 1.
Chapter 14 Maintenance and Inspection
ALARM indicator Time data display area 1
Indications on the monitor
The error message and code also appear superimposed on a monitor connected to the COMPOSITE VIDEO OUTPUT 3(SUPER) connector or SDI OUTPUT 3(SUPER) connector. Depending on the error code, an indication of the source of the problem may appear as a secondary error message.

ERROR-01 REEL TROUBLE-1

Error Message List
Code 09 0A Message NO COMMUNICATION REEL TROUBLE REEL TROUBLE REEL TROUBLE REEL TROUBLE REEL TROUBLE TAPE TENSION CAPSTAN TROUBLE DRUM TROUBLE TH/UNTH MOTOR THREADING HUMID TAPE T/E SENSOR TAPE TOP SENSOR TAPE END SENSOR FAN MOTOR CASS COMP MOTOR REEL SFT MOTOR REEL POS SENSOR THRED RING SENS INTERNAL I/F1 CPU INITIALIZE ERROR OTHERS NV-RAM ERROR SY NV-RAM ERROR SV NV-RAM RF NV-RAM ERROR INTERNAL I/F 2 Description Abnormality in the interface between the lower control panel and SYS CPU (SS-89 board) has been detected in the lower control panel side. Tape slacking has been detected in the threading or unthreading operation. Tape slacking or tape breaking has been detected in the SEARCH, FF,or REW mode. Tape slacking,tape breaking,or supply or take-up reel locking has been detected in the REC or PLAY mode. A malfunctional tape transport speed has been detected in the FF or REW mode. A malfunctional operation of the supply or take-up reel has been detected during cassette insertion. Excessive tape tension has been detected in the REC or PLAY mode. Malfunction of capstan motor has been detected. Malfunction of drum motor has been detected. Malfunction of threading or unthreading operation has been detected. The tape top processing has not been completed in the threading mode. Dew condensation has been detected. The tape top and tape end have been detected simultaneously. Malfunction of tape top sensor has been detected. Malfunction of tape end sensor has been detected. Malfunction of cooling fan motor has been detected. Malfunction of cassette compartment-up or down operation has been detected. Malfunction of movement of the reel table corresponding to the cassette size has been detected. The L-cassette and S-cassette positions of the reel table have been detected simultaneously. The thread end and unthread end states of the threading ring have been detected simultaneously. Abnormality in the interface between SYS CPU (on SS-89 board) and other CPU/ MPU has been detected. Abnormality in the interface between SV CPU (on SS-89 board) and DRUM CPU (on DR-414 board) has been detected. Abnormality has been detected in the operation of an NV-RAM (on FP-133 board). Abnormality has been detected in the operation of an NV-RAM (on SS-89 board) for the system control system. Abnormality has been detected in the operation of an NV-RAM (on DR-508 board) for the servo system. Abnormality has been detected in the operation of an NV-RAM (on EQ-84 board) for the RF system. Abnormality in the interface between SYS CPU (on SS-89 board) and SERVO CPU (on SS-89 board) or MPU (on EQ-84 or DM-123 board) has been detected.

To display the hours meter Press the F5 (MENU) button, then turn the MULTI CONTROL knob to display the required item in the time data display. To exit from the hours meter Press the F6 (EXIT) button.
14-5-2 Maintenance Timings
Use the following table as a timing guide for checking and replacing components of the unit. These intervals are not guaranteed lifetimes; the timing for replacing components depends on the particular conditions of use. In particular, depending on the degree of dirt contamination and abrasion, pinch rollers and cleaners may require replacement earlier than suggested by this table.
Note that an arrow in the table means that the component to be replaced is part of the assembly the arrow points to, which must be replaced as a whole.
For information on severe conditions (frequent threading/ unthreading) or how to replace components, refer to the Maintenance Manual Volume 1.
Component Upper drum Drum assembly Brush slip ring assembly Video head cleaner (roller) Pinch roller assembly Reel table assembly Pinch application assembly Fan motor (card) Fan motor (MD) Power supply unit
Guideline replacement intervals Digital hours meter indication (menu number in R: Replace C: Check, and replace if necessary parenthesis) 1000 hrs 2000 hrs 3000 hrs 4000 hrs 5000 hrs 6000 hrs C C C C() Drum running time (H02) C R R Tape running time (H03) R R (Replace at interval of 4000 hours.) Tape running time (H03) Operation time (H01) Replace after 40,000 hours Replace after 40,000 hours Replace after 40,000 hours R R() R R

Specifications

General
Recording format Digital Betacam Power requirements 100 to 240 VAC, 50/60 Hz Power consumption 2.2 A (220 W) (DVW-M2000/ M2000P) 2 A (200 W) (DVW-2000/2000P) Peak inrush current (1) Power ON, current probe method: 54 A (240 V), 20 A (100 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 16 A (230 V) Operating temperature 5C to 40C (41F to 104F) Storage temperature 20C to +60C (4F to +140F) Humidity 20 to 90% Mass DVW-M2000/M2000P: 23.5 kg (51 lb 12 oz) DVW-2000/2000P: 22 kg (48 lb 8 oz) Dimensions (w/h/d) 544 mm (16 7/3/1/2 inches) Betacam SX playback time (DVW-M2000/M2000P) 194 minutes with BCT-194SXLA Analog Betacam playback time (DVW-M2000/ M2000P) 90 minutes with BCT-90MLA (525/60) 108 minutes with BCT-90MLA (625/50) Fast forward/ rewind time Approx. 3 minutes with BCT184MXL Search speed Shuttle mode Digital Betacam playback: Still to approx. 50 times normal playback speed MPEG IMX playback (DVWM2000/M2000P): Still to approx. 78 times normal playback speed Betacam SX playback (DVWM2000/M2000P): Still to approx. 78 times normal playback speed Analog Betacam playback (DVWM2000/M2000P): Still to 35 times normal playback speed (525/60) Still to 42 times normal playback speed (625/50) Variable speed mode Digital Betacam playback: 1 to +3 times normal playback speed MPEG IMX playback (DVWM2000/M2000P): 1 to +3 times normal playback speed Betacam SX playback (DVWM2000/M2000P): 1 to +2 times normal playback speed Analog Betacam playback (DVWM2000/M2000P): 1 to +3 times normal playback speed Jog mode Still to 1 times normal playback speed Servo lock time 0.5 (525/60)/0.7 (625/50) second or less (from standby on) Load/unload time 6 seconds or less

AC IN connector 2-17 ALARM indicator 2-11 Analog audio input/output section 2-15 device connection 3-2 video input/output section 2-16 ASSEMBLE button 2-11 Audio monitor signal output section 2-18 selection function selector buttons 2-4 setting display section 2-5 signal selection buttons 2-5 AUDIO IN/OUT buttons 2-12 AUDIO INPUT (AES/EBU) connectors 2-16 AUDIO INPUT CH1 to CH4 connectors 2-15 AUDIO INPUT CH1 to CH4 and CUE IN LEVEL switches 2-15 AUDIO OUTPUT (AES/EBU) connectors 2-16 AUDIO OUTPUT CH1 to CH4 connectors 2-15 AUTO EDIT button 2-13 Auto Event Detector output/recording 10-1 overview 10-1 Connector panel 2-15 Continuous editing 5-13 CONTROL PANEL connector 2-18 Control panels 2-1 CTL/TC (function menu) 11-3 CUE button 2-11 CUE IN/OUT connectors 2-15, A-5 recording 9-2 Extended menu items 12-8 External device connectors 2-17
F FWD button 2-11 Features 1-1 525/625 indicator 2-7 F1 to F6 buttons 2-6 Format indicators 2-2, 2-7 Function menu configuration 11-1 item 11-3 operation 2-6
DELETE button 2-12 DF (function menu) 11-4 DF indicator 2-7 Digital audio input/output section 2-16 device connection 3-1 hours meter 14-5 signal input/output section 2-17 Digital Betacam cassettes 3-10 format 1-1 tapes A-2 DISPLAY FULL/FINE button 2-4 DMC editing 5-11 playback 4-12 DMC EDIT button 2-12 DOLBY (function menu) 11-7 DOLBY NR indicator 2-8 Drop frame mark 3-9 mode 11-4

Ground terminal 2-17

Head Cleaning 14-1 Head configuration 1-1 Headphones 2-2 HOME button 2-6 HUE (function menu) 11-5
IN/OUT buttons 2-12 INPUT button 2-4 Input signal selection 2-4 INSERT buttons 2-11
Basic menu items 12-5 Betacam Cassette 3-10 compatibility 1-2 SX/SP cassette 3-10 BLACK (function menu) 11-5
EDIT button 2-10 Edit point 5-3 cue-up and preroll 5-7 modifying and deleting 5-6 setting buttons 2-12 Editing automatic editing 5-1 carrying out 5-8 continuous editing 5-13 control section 2-12 cross-fade editing 12-14 manual editing 5-14 mode setting section 2-11 preread editing 5-14 quick editing 5-13 selecting the editing mode 5-3 special methods 5-13 split editing 5-4 standalone editing 5-14 switch/menu settings 5-2 E-E mode 2-5, 2-10 EJECT button 2-2 EMPHSS (function menu) 11-6 ENTRY button 2-13 Error messages 14-2 Essence mark output 9-2 overview 9-1
JOG button 2-9 indicator 2-9 Jog mode 4-8
C PHAS (function menu) 11-5 CAPSTN (function menu) 11-7 Capstan override function 4-9 Cassettes 3-10 CD-ROM manual 1-5 CH1 to CH4 buttons 2-11 CHANNEL CONDITION indicator 2-6 CHARA (function menu) 11-7 CHROMA (function menu) 11-5 COMPONENT VIDEO INPUT connectors 2-16 COMPONENT VIDEO OUTPUT connectors 2-16 COMPOSITE VIDEO INPUT connectors/ 75 termination switch 2-16 COMPOSITE VIDEO OUTPUT connectors 2-16 CONFI (ON)/PREREAD indicators 2-8 CONFI (function menu) 11-3 CONFI playback 2-8 Connections to analog devices 3-2 to digital devices 3-1

UMID (function menu) 11-8 UMID display 8-4 output 8-4 overview 8-1 recording 8-2 Upper control panel 2-2 User bit values 4-2
VAR button 2-9 Variable speed mode 4-9 VIDEO (function menu) 11-5 VIDEO button 2-11 VIDEO CONTROL connector 2-18 Video test signal (setup menu item 710) 12-22 VID.IN (function menu) 11-3 VIN LV (function menu) 11-6 VITC (function menu) 11-4 VITC external sync 4-4 field 3-9 V.PROC (function menu) 11-5

Quick Editing 5-13

REC button 2-10 controls 2-6 REC INHI indicator 2-10
YC DLY (function menu) 11-5
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.

Sony Corporation

DVW-M2000/M2000P DVW-2000/2000P (SY) 3-826-013-07(1) Printed in Japan 2009.2004