How to pair my Bluetooth Headset/Handsfree HBH-30/-35/-60/-65/-200/-300/-600/-602/-608/-610/ -660/-662 with a D750
Pairing, sometimes called bonding/adding, two devices with each other means that both devices will work together when switched on and within range. Pairing is done once and normally there is no need to repeat this procedure. Please follow the description below. Note that the description for preparing your phone is found at the end. 1. 2. 3. HBH-30/HBH-35/HBH-60/HBH-65 (NOT the HBH-200) Make sure that the headset is fully charged, switched on and within 1 m (3 ft) of the phone. Press the CALL HANDLING BUTTON for approximately 5 seconds until your hear a long high frequent beep and the light flashes red and green. The headset is now in Pairing mode. Prepare the phone according to the description below. HBH-200 Make sure that the handsfree is fully charged, switched on and within 1 m (3 ft) of the phone. Enter the menu in the HBH-200 by pressing the ON/OFF BUTTON and the CALL BUTTON (the round button on the side) at the same time quickly. Use the + or the - button and scroll to ADVANCED and press the CALL BUTTON to confirm. Select NEW PHONE and press the CALL BUTTON. In the HBH-200 display, READY TO ADD PREPARE PHONE appears. Prepare the phone according to the description below. HBH-300/-600/-602/-608/-610 Make sure that the headset is fully charged, switched on and within 1 m (3 ft) of the phone. The first time you turn your headset on, it immediately goes into pairing mode. The light flashes red and green. If so, please proceed to the phone instructions below. To manually prepare the headset, press the two VOLUME BUTTONS, (+) and (-), at the same time for approximately 5 seconds until your hear a long high frequent beep and the light flashes red and green. The headset is now in Pairing mode.

1. 2. 3. 4. 5. 6.

1. 2. 3.
HBH-660/-662 Make sure that the headset is fully charged, switched on and within 1 m (3 ft) of the phone. The first time you turn your headset on, it immediately goes into pairing mode. There are three symbols showing in the headset display: a headset, two rotating arrows and a phone. If so, please proceed to phone instructions below. To manually prepare the headset, press the two VOLUME BUTTONS, (+) and (-), at the same time for approximately 5 seconds, until your hear a long high frequent beep. There are three symbols showing in the headset display: a headset, two rotating arrows and a phone. The headset is now in Pairing mode. D750 Enter the main menu, scroll to SETTINGS, and select the CONNECTIVITY tab. Select BLUETOOTH, MY DEVICES. Select NEW DEVICE, Add. The phone starts searching for devices. Make sure that the headset is in pairing mode. When the HBH-xxx becomes visible in the DEVICES FOUND menu, highlight it and press Select. Enter the PASSKEY (0000 by default) and press Ok. HBH-xxx is now added to the list of paired devices and is ready to use.

1. 2. 3. 4. 5. 6. 7.

How to pair my Bluetooth Headset/Handsfree HBH-30/-35/-60/-65/-200/-300/-600/-602/-608/-610/-660/-662 with a P900/P908
Pairing, sometimes called bonding/adding, two devices with each other mean that both devices will work together when switched on and within range. Pairing is done once and normally there is no need to repeat this procedure. Please follow the description below. Note that the description for preparing your phone is found at the end. 1. 2. 3. HBH-30/-35/-60/-65 (NOT the HBH-200) Make sure that the headset is fully charged, switched on and within range from the phone. (Not more than 1 meter) Press the CALL HANDLING BUTTON for approximately 5 seconds until your hear a long high frequent beep and the light flashes red and green. The headset is now in Pairing mode. Prepare the phone according to the description below. HBH-200 (The handsfree does not support full functionality with the P900/P908.) Make sure that the handsfree is fully charged, switched on and within 1 m (3 ft) of the phone. Enter the menu in the HBH-200 by pressing the ON/OFF BUTTON and the CALL BUTTON (the round button on the side) at the same time quickly. Use the (+) or the (-) button, and scroll to ADVANCED and press the CALL BUTTON to confirm. Select NEW PHONE and press the CALL BUTTON. In the HBH-200 display, READY TO ADD PREPARE PHONE appears. Prepare the phone according to the description below. HBH-300/-600/-602/-608/-610 Make sure that the headset is fully charged, switched on and within 1 m (3ft) of the phone. The first time you turn your headset on, it immediately goes into pairing mode. The light flashes red and green. If so, proceed to phone instructions below. To manually prepare the headset, press the VOLUME BUTTONS, (+) and (-), at the same time for approximately 5 seconds until your hear a long high frequent beep and the light flashes red and green. The headset is now in Pairing mode.

1. 2. 4. 5. 6. 7.

1. 2. 3.
HBH-660/-662 Make sure that the headset is fully charged, switched on and within 1 m (3 ft) of the phone. The first time you turn your headset on, it immediately goes into pairing mode. There are three symbols showing in the headset display: a headset, two rotating arrows and a phone. Proceed to the phone instructions below. To manually prepare the headset, press the VOLUME BUTTONS, (+) and (-), at the same time for approximately 5 seconds, until your hear a long high frequent beep. There are three symbols showing in the headset display: a headset, two rotating arrows and a phone. The headset is now in Pairing mode.

1. 2. 3. 4. 5. 6. 7.

P900/P908 In the Application view, tap CONTROL PANEL, CONNECTIONS tab, BLUETOOTH. Tap the SETTINGS tab and set Bluetooth to ON. Select the DEVICES tab and press ADD. The phone starts searching for Bluetooth devices. Make sure that the headset is in pairing mode When the HBH-xxx becomes visible in the AVAILABLE DEVICES menu, tap it. Enter the PASSKEY (0000 by default) and press DONE. On the screen, BONDING COMPLETED appears. Tap DONE and HBH-xxx is added to the list of Bluetooth devices and is ready to use.