Ring signal off indicator Alarm indicator Silent indicator SMS indicator
No sound can be heard when you receive a call. The alarm clock has been set and is on.
All audible signals are turned off, except the alarm and timer. You have received a text message.

Voice mail indicator

You have received a voice message, depending on your subscription. Indicates that voice dialling is set to Start on Flip. Line 1 is in use for outgoing calls if you subscribe to the Two Line Service
Voice label in phone indicator Line 1 indicator Line 2 indicator
Line 2 is in use if you subscribe to the Two Line Service.
Display Information and Key Functions
Ciphering indicator Home zone indicator
Ciphering is currently not being provided by the network. You are in your home zone. Does not appear on all networks.
Note! Each menu has got its own symbol. See Menu Graphics on page 21.
The table below explains the key functions.
Key Use Flip release button

Key Functions

To open the flip and answer incoming calls. (To end a call, close the flip.)
To make calls and answer calls. To voice dial, press and hold the key. To enter the Call List from standby. To choose a menu, sub-menu or setting.

C (Clear)

To turn the phone on or off, press and hold the key in standby. To end a call. To reject a call. To go back one level in the menus, to exit a setting or to leave a setting unchanged. To get back to standby mode, press and hold the key. To enter the menu system. To move (scroll) through menus, lists and text.
To erase numbers and letters from the display. To mute the microphone during a call, press and hold down the key. To set the phone silent, press and hold the key from standby. To delete an item from a list.

Number keys

To enter the digits 0-9. The 0 key enters the international prefix (+) if held down. To call your Voice Mail, press and hold the 1 key. To enter the phone book, press and hold any of the numbers 2-9. To move through menus using shortcuts. To enter letters, for example when writing an SMS. To enter *. To shift between upper- and lower-case letters. To enter #.

# (Hash)

Volume key upwards and downwards
To increase or decrease the volume of the earpiece or handsfree loudspeaker during a call. To reject an incoming call, quickly slide the key twice. To voice dial, slide and hold the key when the flip is open To move through the menus. To open the flip without answering a call, slide and hold the key while pressing the flip release button. To enter the Status menu.

characters are sent as tone signals.
Tip! You can also save codes only or codes together with a phone number in your Phone Book. See Telephone Banking Services on page 32. However, it
may be a risk to save your codes in the phone in case it is stolen.

During a Call

The Notepad
If you want to make a note of a phone number during a call, you can use your phone display as a notepad. To use the notepad during a call Use the number keys to enter the number.
Features on page 20. page 42.
When you end the call, the number remains in the display or, if Ask to Save is on, you will be asked to save the number in your phone book. You can also find the number in Add Number in the Phone Book menu. See T28
When you enter the number, the person you are talking to will hear the tones. If you wish, you may turn the tones off during a call. See Turn off Tones on
Checking the Duration or Cost of the Call
During a call, the display normally shows the duration in minutes and seconds. Depending on your subscription, you may see the call cost displayed instead.
Note! This depends on your network and SIM subscription. See Knowing the Call Time/Call Cost on page 73.

Minute Minder

If you turn on the minute minder, you hear a beep once every minute during a call as a reminder of the duration of the ongoing call. See Minute Minder on

page 42.

More than One Call Simultaneously
Your phone is capable of handling more than one call simultaneously. You can put the current call on hold and then make or answer a second call. You can also set up a conference call with up to five people. See Handling More than One Call Simultaneously on page 65.
Er ics No so t fo nM r ob Com ile me Co rci mm al un Use ica tio ns AB

Functions and Settings

T28 Features
Sending and Receiving Text Messages (SMS) Security for Your Phone and Subscription Setting Network Preferences
Handling More than One Call Simultaneously Knowing the Call Time/Call Cost Using Two Voice Lines Voice Control
Sending and Receiving Fax and Data Calls
Using the Menus Your Personal Phone Book Using the Call List Your Voice Mail Service Personalizing Your Phone Diverting Incoming Calls Calling Card Calls Extras The Profile Concept Accessories Online Services

To enter a C, slide the volume key downwards and press 2.
Tip! You can choose another alphabet by pressing and holding #.
Press and hold 0 to enter the + sign.
Saving a Number Together with a Name
Every phone number that you save gets a position number. You can save the your phone numbers. To save a number together with a name phone numbers together with a name to make it easier for you to keep track of
1. Scroll to Phone Book, Y E S , Add Number, Y E S. A list of numbers used but not saved appears. country code) and press Y E S.
2. Select Add New? or any of the numbers from the list by pressing Y E S. 3. Enter a phone number that you wish to save (including the (+) sign and the
4. Enter a name that you want to associate with the phone number and press 5. You now have three options:
To save the number in the suggested first empty position, press Y E S. To save the number in another position, press C to erase the position
number, enter a new position number and press Y E S.
To save the number in the phone memory, you need to know how many positions you have got on your SIM card. You can check this in Memory Status in the Phone Book menu. If, for example, you have 200 positions on your SIM, you can enter position number 201 to save a number in the phone memory.
If you have turned Voice Dialling on, you are asked if you want to add a voice label to your phone book entry. See Voice Control on page 76.

Ask to Save

If you wish to be asked to save any dialled or answered number that is not already saved in your phone book, you can turn on the Ask to Save option. To turn the Ask to Save function on or off
1. Scroll to Settings, Y E S , Display, Y E S , Help Functions, Y E S , Ask to Save, Y E S. 2. Select On or Off.
Note! Your subscription must support the Calling Line Identification service.
Calling a Number Saved In the Phone Book
You can either call a number by using the name saved with it or you can call the number by using the position number that it was saved in.
The order of searching for names and numbers depends on the sort order you have chosen, i.e. by name or by position.
To choose a sort order 2. Select a sort order. To call a number saved in the phone book 1. Scroll to Phone Book, Y E S , Find and Call, Y E S. associated with the number that you want to call.
3. Press Y E S. If the name displayed is not the one you want, press find the correct name and number.
2. Enter the position number or the name (or the first few letters of the name)

4. Press Y E S to make the call.
Tip! A quicker way to enter the Find and Call function is to press and hold.
Shortcuts to Phone Book Entries
When in standby, you can find an entry by:
entering the position number followed by #.
pressing and holding one of the keys 2-9 to find an entry beginning with a specific letter. For example, pressing and holding 2 takes you to the first entry beginning with the letter A (or closest following). or to
Once you are in the list of phone book entries you can use
scroll through the positions, or enter a position number or a letter to go to a certain entry.

Speed Dialling

You can call the phone numbers that you have saved in positions 19 in the
memory by entering the position number and then pressing Y E S. Example:

1. Enter the number 3.

2. Press Y E S to make the call.
Keeping the Phone Book Up to Date
You may need to change the names and numbers in the phone book from time to time. You may also want to change the position number of an entry. Editing a Phone Number In the Phone Book
You need to find the phone book entry that you wish to edit. You can use either the stored position or the name. See Calling a Number Saved In the Phone Book on page 29.

until you

1. Scroll to Phone Book, Y E S , Options, Y E S , Sort Order, Y E S.
To edit an entry 2. Enter the position number or the name of the entry that you wish to edit. Press Y E S. If the name displayed is not the one you want, press find the correct name and number. 3. Press Y E S to select the entry. 4. Select Edit. Use the or
5. Edit the number and press Y E S. or 6. Edit the name and press Y E S.
keys to move the cursor. Use the C key to delete.
7. Edit the position number and press Y E S.

Overwrite Protection

If you try to save a phone number in a position which already contains a phone number, the message Overwrite? appears together with the name saved in that position. You now have two options:
To save the number in the selected position
Press Y E S to replace the number with the new one.
To save the number in a different position

1. Press N O.

2. Enter the new position number.
3. Press Y E S to save the number in the new position.
When the Card Memory Is Full
When all SIM card positions are full, an icon appears next to the position number, see margin. From now on your entries are stored in the phone memory.
If all positions, including the phone memory are full, you have to delete an old number by entering a position that is already occupied and press Y E S. To delete an entry from the memory
1. Scroll to Phone Book, Y E S , Find and Edit, Y E S.
2. Enter the position number or the name of the number that you want to delete and press Y E S. (This depends on the sort order, i.e. by name or by position.)

Tip! If you do not wish to disturb other people, use the volume key on the side
If you subscribe to the Two Line Service, you can set different ring signals for
Provided your SIM subscription supports Fax and Data calls, you can set
If your subscription includes the Calling Line Identification (CLI) service, you can assign a personal ring signal to up to ten callers. You can, for example, have one ring signal for your friend and another one for your
If the last seven digits of a callers number correspond to a number you have
You can include question marks (?) in a phone number. For example, 012345??? means that calls from phone numbers between 012345000 and 012345999 will have the same personal ring signal. You get a question mark
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S , Personal Rings,
2. Enter the callers number and press Y E S.
You can also recall it from the Phone Book by pressing
3. Select the ring signal type you want.
To delete a callers number
2. Scroll to the number you wish to delete and press Y E S. 3. Select Delete.

Composing Ring Signals

You can compose four different ring signals. To compose a ring signal
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S , My Melodies, 2. Select My Melody 1, My Melody 2, My Melody 3 or My Melody 4.
3. Press C to clear the display.
4. Use the keypad to enter notes.
The keypad now works as a keyboard (see figure in margin above): Press and hold a key to enter a long note. Press 0 to raise the note one octave.
Press # once to raise the note one semitone.
Press # twice to lower the note one semitone.
5. To listen to your melody, press Y E S.
6. Press Y E S again to save it or press N O to continue editing.

Vibrating Alert

You can choose to be notified of an incoming call by the buzzing of the Vibrating Alert. You can set the phones Vibrating Alert to one of the following: On (all the time)
On If Silent (on when the ring volume is turned off or when you have set the phone to silent) Off (all the time)
Note! When your phone is placed in a desktop charger or a handsfree car kit, the Vibrating Alert is turned off automatically. To set the Vibrating Alert
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Vibrating Alert, Y E S. 2. Select the setting you want.

Message Signal

You can choose whether to hear clicks, tones or nothing (silent) when you receive a voice or text message (SMS).
To set the message signal

If your SIM card does not contain the phone number to your network service centre, you must specify the number yourself. Otherwise you cannot reply to received messages or send your own messages. See Enable the Phone to
Note! The Short Message Service may not be available on all networks. Some network operators may only allow SMS to be sent within their own network.
Enable the Phone to Send SMS
If you want to send or reply to a message, you need to make sure that your network operators Service centre number is set. Most modern SIM cards already contain this information at the time of purchase. You can obtain the service centre number from your network operator.
To activate a service centre number found in the list
1. Scroll to Messages, Y E S , Options, Y E S , Service Centres, Y E S. 2. Scroll to the number you want and press Y E S.

3. Select Activate.

If no number is found in the list, you have to set the number yourself. To enter the phone number to your service centre
1. Scroll to Messages, Y E S , Options, Y E S , Service Centres, Y E S , Add new?, Y E S. and press Y E S.
2. Enter the number, including the international (+) sign and country code
Sending and Receiving Text Messages (SMS)

Composing a Text Message

For more information on how to enter text and the letters, see Entering Letters on page 28. Example: To enter an A, press 2 once. To enter a B, quickly press 2 twice.
again. To enter numbers, press and hold any number key. To delete letters and numbers, press the C key. You may also use the volume key as a shortcut to certain letters: To enter a B, slide the volume key upwards and press 2. To enter a C, slide the volume key downwards and press 2. Tip! You can choose another alphabet by pressing and holding #.
Sending a New Text Message
1. Scroll to Messages, Y E S , Send New, Y E S. 2. Enter your message and press Y E S. pressing.
3. Enter the recipients phone number or recall it from the phone book by 4. Press Y E S to send the message.
5. Sending message appears in the display followed by Message has been sent.
Note! If you have turned on any of the Set On Send options (Message Type,

To divert a call
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S.
Not Reachable, Fax Calls or Data Calls) and press Y E S.
2. Scroll to the divert you want to turn on (All Voice Calls, When Busy, No Reply, 3. Select Activate.

Diverting Incoming Calls

4. A phone number recently used for the divert function or a number recently phone number, including the area code, to which you want your calls to be diverted and then press Y E S. If you need to delete numbers, press C.
Tip! If the phone number is stored in the phone book, you do not need to enter

it. Press

and then recall the number.
When you turn on the All Voice Calls divert, an icon is shown in standby. Note! When the Restricted Calls function is on, some Divert Calls options cannot be activated. See Security for Your Phone and Subscription on page

Cancelling Divert Calls

To cancel a certain Divert Calls
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S. 2. Scroll to the divert you want to cancel and press Y E S. 3. Select Cancel.
The message Please wait appears, followed by a message which informs you
that the Divert Calls has been cancelled.
Checking the Divert Status
To check the status of a certain Divert Calls
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S. 3. Select Get Status.
2. Scroll to the divert you want to check and press Y E S.
whether the Divert Calls is on or not.
To check the status of all Divert Calls
Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S , Check All, Y E S.
present in the display will be suggested as a divert number. Enter the
There are several ways to protect your phone and subscription from control.
unauthorized use. Anything from a SIM card lock to full phone number

The SIM Card Lock

The SIM card lock only protects your subscription and not your phone itself from unauthorized use. If you change SIM cards, the phone still works with the new SIM card.
Most SIM cards are locked at the time of purchase. If the SIM card lock is on, you have to enter the PIN (Personal Identity Number) every time you turn on your phone. If you enter your PIN incorrectly three times in a row, the SIM card is blocked. This is indicated by the message PIN blocked. If this happens you need to unblock it to access your subscription. To unblock your SIM card

1. PIN blocked appears.

2. Enter your PUK (or PUK2) which you will find in the information supplied by your network operator. 3. Press Y E S. 5. Press Y E S. 7. Press Y E S.
4. Enter a new four- to eight-digit PIN (or PIN2). 6. Re-enter the new PIN (or PIN2) to confirm.
Note! If you enter the wrong PUK ten times in a row, your card is permanently
blocked. If this happens, you should contact your network operator. To change your PIN code

The Fixed Dialling function allows calls to be made only to certain numbers saved on the SIM card. If an attempt is made to call other numbers, the message Number not permitted appears in the display.
It is possible to save partial numbers, for example an area code, or an area code followed by the first digits common to several numbers. Storing 0123456 allows calls to be made to all numbers starting with 0123456. Numbers beginning with the international (+) sign and country code can also be saved, allowing you to make calls abroad.
Numbers which include question marks can be saved. A question mark should be read as a wild card, i.e. it can represent any number (0-9). To enter a question mark press and hold #.
1. Scroll to Settings, Y E S , Call Options, Y E S , Restrict Calls, Y E S , Cancel All, Y E S.
Note! The Fixed Dialling service does not prohibit calls to the international
To turn the Fixed Dialling service on or off 1. Scroll to Phone Book, Y E S , Options, Y E S , Fixed Dialling, Y E S. 2. Enter your PIN2 and press Y E S. 3. Select On or Off.
To save fixed numbers 1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S , Add new?, Y E S. 2. Enter your PIN2 and press Y E S. 3. Enter the fixed number and press Y E S. To edit a saved fixed number 1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S. 3. Select Edit. 2. Scroll to the fixed number that you want to edit and press Y E S. 4. Enter your PIN2 and press Y E S. 6. Edit the name and press Y E S. 5. Edit the fixed number and press Y E S. 7. Enter the position number and press Y E S. To delete a fixed number 1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S. 3. Select Delete. 2. Scroll to the fixed number that you want to delete and press Y E S. 4. Enter your PIN2 and press Y E S. The fixed number is deleted.
4. Enter the name you want to associate with the number and press Y E S.

Closed User Groups

The Closed User Group (CUG) function is another way of lowering call
costs. It depends entirely on your operator and subscription. Not all networks support this function.
Your network operator can place certain numbers in groups. On some networks it is cheaper to make calls within a call group. You can have a maximum of 10 groups.
To add a Closed User Group
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S , Edit List, Y E S , 2. Enter the name of the Closed User Group and press Y E S.

emergency number 112.

3. Enter the index number of the group and press Y E S. Note! The index numbers are provided by your network operator. To activate a Closed User Group 2. Scroll to the group you want to activate and press Y E S. Calls can only be made within the selected user group. To call outside Closed User Groups

If the Call Waiting service is on, you hear a tone in the earpiece if you receive a second call. The number or name of the caller is normally shown at the top of the display together with a list of the alternatives Answer, Busy and
Unknown is shown. You can do one of the following: Put the current call on hold and answer the waiting call Press Y E S to answer the waiting call. The current call is now put on hold. in black. Continue the current call and reject the waiting call Select Busy. hears a busy tone. you have specified. End the current call and answer the waiting call Select Release&answer.
Release&answer. If the incoming call is a restricted number, the display shows Withheld. If the incoming call is a number without any CLI service,
Your held call is marked in grey in the display and the active call is marked
The waiting call is rejected. If the callers network supports it, the caller
Note! If Divert When Busy is on, the waiting call is diverted to the number
One Active Call and One Call On Hold
When you have one active call and one call on hold, you can do one of the following:
Switch between the two calls Press Y E S.
End the active call and return to the call on hold
1. Press N O. The question Retrieve call? appears. 2. Press Y E S.
If you press N O , also the call on hold will be ended.

End both calls

Scroll to Call Handling, Y E S , Release All, Y E S.
Connect the two calls (Call Transfer) The two calls are now connected to each other, and you are disconnected from both calls.
Note! The Call Transfer service may not be available on all networks.
Join the two calls into a Conference Call See Conference Calls below. Scroll to Call Handling, Y E S , Join Calls, Y E S.

Receiving a Third Call

If the Call Waiting service is on, you may receive a third call when you have one active call and a second call on hold. From now on, you cannot answer any more calls without disconnecting one, if you do not want to create a conference call. You hear a tone in the earpiece and Busy and

Preparing your Phone for Voice Dialling
When you buy your phone, voice dialling is set to on. If, for some reason, it has been turned off, you will need to turn it on again before you can start using it.
To turn Voice Dialling on
1. Scroll to Settings, Y E S , Voice Control, Y E S , Voice Dialling, Y E S. Your phone is now ready to record voice labels.
Note! Once you have turned voice dialling on, you are asked if you want to record a voice label every time you save a new number in your phone book. See Saving a Number Together with a Name on page 29.
Before you can use voice dialling, you need to record voice labels for your phone book entries. To get a good result when recording voice labels, make sure you are in a quiet environment.
To record voice labels for existing phone book entries
1. Scroll to Phone Book, Y E S , Voice Labels, Y E S , Add voice?, Y E S.
2. Select a phone book entry to which you want to add a voice label. 3. Wait for the tone and say the name (voice label) that you want to save. The voice label is played back to you. 4. Press Y E S to save the voice label you have recorded. If you do not find the recording OK, repeat step 3.
An icon appears next to those phone book entries for which you have saved a voice label. You can save 10 voice labels in the phone.
You can also record voice labels in Find and Edit in the Phone Book menu.

Voice Control

Note! To use voice dialling with a vehicle handsfree unit, you need to record Voice labels for phone book entries recorded in the phone will not be available in the car, and vice versa. For more information about the Vehicle Handsfree unit, see Vehicle Handsfree on page 94. Recording Problems happened:
you spoke too softly - try speaking louder you spoke too late or too soon - speak after the tone Go back to step 1 of To record voice labels for phone book entries. Listening to and Editing Voice Labels have voice labels. To listen to and/or edit the voice labels saved in your phone book 1. Scroll to Phone Book, Y E S , Voice Labels, Y E S. The voice label is played back to you. 2. Scroll to the entry that you want to edit. 3. Press Y E S.

1. Scroll to Phone Book, Y E S , Calling Cards, Y E S. 3. Select Delete. 4. Press Y E S. 2. Scroll to the card number that you want to delete and press Y E S. The question Delete? appears in the display. The card number has been deleted. To edit a card number 1. Scroll to Phone Book, Y E S , Calling Cards, Y E S. 2. Scroll to the card number that you want to edit and press Y E S. You may now edit the card number. 3. Select Edit. 4. Press Y E S to confirm the new number. You may now also edit the name and code.

Choosing a Card

If you have saved two card numbers, you must choose which card you want to use before making a calling card call. To select a card
1. Scroll to Phone Book, Y E S , Calling Cards, Y E S. 2. Enter your phone lock code and press Y E S. 3. Select the card that you want to use. 4. Select Activate card.
Making a Calling Card Call
1. Enter the phone number of your calling card server or retrieve it from the Phone Book by pressing and holding.

2. Press and hold Y E S.

The access number of the calling card server is called and during the connecting phase, you are asked to send the phone number of the person that you want to call and the verification code, in the order chosen earlier (see above).
verification code first and press Y E S to confirm your choice.
3. To send the number and verification code during the connecting phase, sent automatically. Now you are connected to your personal phone call.
press Y E S when the display shows Send or wait a few seconds and they are

browser.

Note! To be able to use various communications services you need the appropriate software such as a fax program, an e-mail program or an Internet
Sending Fax and Data Calls
All fax and data calls are initiated from the appropriate computer software. To send fax and data calls you need to connect your phone to a computer, for example by means of an infrared modem and then start the appropriate software program.
Receiving Fax and Data Calls
The procedure of receiving fax and data calls depends on your network and subscription. If you have different numbers for voice, fax and data calls, this is referred to as multi numbering. This means that you can have up to three numbers in your subscription. If you only have one number for all call types, this is referred to as single numbering.

Line 1/2 Silent

L1 Off On Off Off Off On
Auto Activation Off Accessories

Vehicle HF -

Handsfree -
You can always choose a profile manually. To select a profile manually
1. Scroll to Settings, Y E S , Profiles, Y E S , Select Profile, Y E S.
2. Select the profile you want.
You can also find Select Profile in the My Shortcuts menu. The quickest way to reach this sub-menu is to press and hold.
If you choose a profile other than Normal, an icon is shown in standby.
Note! A profile which is not associated with any accessory, such as Meeting
or Normal, must be chosen manually, even if automatic activation is on. The profiles associated with accessories can be chosen automatically. See

Accessories on page 91.

Changing the profile settings
You can re-name the pre-programmed profiles and change the settings
according to your wishes.
To change the name of a profile
1. Scroll to Settings, Y E S , Profiles, Y E S , Profile Name, Y E S. 2. Enter a new name and press Y E S. To change a profile setting
1. Scroll to Settings, Y E S , Profiles, Y E S , Edit Profile, Y E S. A list of the profile settings appears. 2. Select a setting by pressing Y E S.
3. Change the profile setting according to your wishes.
For information, see the relevant chapters Personalizing Your Phone on page 39, Security for Your Phone and Subscription on page 58, Calling
Off From All Off None Auto L1 Off Off 89
Card Calls on page 79 and Accessories on page 91. If you change a setting which is included in a certain profile, the profile is back to the way they were set when you bought your phone. To reset the profile settings
updated. With the Reset Profiles function, you can change all profile settings
1. Scroll to Settings, Y E S , Profiles, Y E S , Reset Profiles, Y E S. The profile settings are reset.

90 The Profile Concept

the phone is used separately. charger Portable handsfree calling Handsfree calling in your car Infrared communication between your phone and computer different profiles. activated automatically. wish, you may turn it off. To turn automatic activation on or off 1. Scroll to Settings, Y E S , Profiles, Y E S , Auto Activation, Y E S. 2. Select On or Off. activated automatically. See The Profiles on page 88.

Accessories

By using your T28 together with Ericsson original accessories, you have access to a large range of useful features, in addition to those you have when Automatic divert of incoming calls when the phone is placed in a desktop

Note! This is on condition that the specific accessories exist in your market. The Profiles concept, see The Profile Concept on page 88, allows you to
instruct your phone to activate a specific profile automatically when used together with a certain accessory. On the following pages you can find information on how different accessories interact with your phone and its
Note! You are informed of the current profile when you slide the volume key upwards or downwards in standby mode or when you choose another profile. Every time you disconnect your phone from the accessory, the profile is changed to the one which was active before, if the current profile was
For the profiles associated with an accessory to change automatically, the automatic activation must be on. When you buy your phone, the automatic activation is set to On for the Vehicle and Portable handsfree units. If you
Note! You can always choose a profile manually, even if a profile has been

Desktop Charger

If you use the T28 with a specific Ericsson Desktop Charger you have access to some useful features besides ordinary charging. You can choose to make home number when you place your phone in the charger.
the phone switch to the Home profile automatically and divert all calls to your
you place your phone in the desktop charger. Placing the Phone in the Desktop Charger 1. Place the phone in the desktop charger as shown and press backwards to attach the phone. contact your local Ericsson retailer. in the display. with any profile). example the Home profile. 4. The message Divert when connected to accessory? appears. Press Y E S. for example, you place the phone in the desktop charger. (If you press N O , your calls will not be diverted).

92 Accessories

To be able to use these features, you need to make some settings the first time
2. Pull the phone towards you and upwards to detach the phone from the charger.
Note! For further instructions on how to connect the desktop charger, please
To associate the desktop charger with a profile and a divert number
1. Place the phone in the desktop charger. The message Choose profile? appears
2. Press Y E S. (If you press N O , the desktop charger will not be associated 3. Select a profile that you want to associate with the desktop charger, for

dm o [ m b

dm o [m b {

p YES

m m d m

^ dm o {

dm o

j YES

dm m

SIM m b

V b V

SIM ? m n

? m

? f ?

SIM m ?

SIM ?

SIM q i

SIM ?

YES YES YES YES

V D

? V C

YES YES YES YES

? V D

j m

m m m m

m m Ef

YES m m

YES m

YES o YES

o o m

m m b

SIM ? q m m b

YES YES YES

GBP m V

Z

z mm

YES

p p

q k [

l i n

(SMS)

< P

< a

YES < YES<

b <

YES n

b i

YES YES n b

b ^ ?

?

m mm

YES <

YES < YES YES

[k D

YES YES n YES

YES YES n YES

YES YES n YES

m m mm

D n

YES E YES

?

m

[q [ n

Tetris

Tetris n Tetris

YES YES YES
Start l ? Quit Help High-score

Tetris Start

Tetris; Elorg. Classic Tetris; Elorg Tetris logo by Roger Dean; The Tetris Company

Solitaire

Solitaire n

E ?

? m o ?
Solitaire Resume game New game Help Resume game { Start

Solitaire YES

o b
Normal Meeting In Car Outdoors Port H-free Home

v ? m Z

v D

YES YES v YES

? ?

Z oPm

YES v YES YES

YES v YES v YES

f Z {

YES v YES v

Ericsson T28

[ v v q

YES v YES

Ericsson T28

EWm D

m ? n

m ? n D

Ericsson m m

? n W D

v D D b ?

[ v D {

T28 D Ericsson

Z m D b ;

?

b <

< ?

? v b

T28 Ericsson m

Z m b

Ericsson

b <

n ? m n

n { V [q [ [

? mm @

k y

? m j

NO m

k b

T28 Ericsson k b [{ PC x k

PC { //NT. m SMS

Ericsson m m

YES YES v YES

YES YES v YES C

i c ?

H l

SIM D b n p D b

b ; V

[ l y

T28 l

SIM l

SIM l V SIM
SIM m SIM SIM b

T28 ?

j YES l YES

SIM Y E SIM l

Stockholm June 8, 1999 Johan Siberg, President

? m < <

c c

? Z Z

SMS n [d

MIS m

[m f

Accepted Callers

Set on Send

function

[ o ?

[ [ Z Z

Accepted Callers List

Z Z

[ o

Accepted Callers List

m [ m

^ dm o

m b

? m j

PIN PIN PIN PUK