FLAT WIDE DISPLAY

FWD-40LX1 FWD-32LX1R
PROTOCOL MANUAL 1st Edition

Table of Contents

1. Communication Parameter... 1 2. Pin Configuration.... 1 3. Communication Data Format.. 1 4. General Function... 3 5. Picture/Sound... 11 6. Size/Shift... 13 7. Status Enquiry.... 15 8. User Reset.... 18
1. Communication Parameter
Communication system Synchronous system Baud rate Character length Parity Start bit Stop bit Flow control RS-232C Asynchronous communication 9600 bps 8 bit None 1 bit 1 bit None
3. Communication Data Format
(a) Control (Host Request of Write to Display)
No. 5 : : Item Header Category Function Data1 (Length) Data2 (Data1) : : Data (X-3) Check Sum Value 0x8C:Control 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX 0xXX

2. Pin Configuration

Display side (D-sub 9-pin) Host side (D-sub 9-pin)
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a value exceeds 255 (1 byte). * Set the command interval to 500 ms or more when transmitting the Control command continuously. * Set the command interval to 500 ms or more when transmitting the same command (Enquiry) after the Control command.
(b) Enquiry (Host Request of Read to Display)

Personal computer

Item Header Category Function Data1 Data2 Check Sum
Value 0x83:Enquiry 0xXX 0xXX 0xFF 0xFF 0xXX
_ External view _ Pin No. 9 Signal NC RD TD NC GND NC NC NC NC
* Check Sum: Sum total of 1 to 5. Lower one-byte data is validated when a value exceeds 255 (1 byte).
(c) Answer (Display Response to Host) 1 Answer at the time of Control request
No. Item Header Answer* Value 0x70: Answer 0x00: Completed (Normal completion) 0x01: Limit Over (Abnormal completion: Over upper limit) 0x02: Limit Under (Abnormal completion: Under lower limit) 0x03: Command Canceled (Abnormal completion) 3 Check Sum 0xXX

4 Error Answer

No. Item Header Answer* Value 0xE0:Answer 0x00: No Function Error 0x01: Check Sum Error 0x02: Data Length Error 3 Check Sum 0xXX

* 0x00: Completed

Packet is correctly received and process is also correctly completed. 0x01: Limit Over Packet is correctly received, but the data value is over the upper limit. 0x02: Limit Under Packet is correctly received, but the data value is under the lower limit. 0x03: Command Canceled Packet is correctly received, but the data value is not correct or the request cannot be accepted in the current host state. * Check Sum: If the value of a sum total of 1 and 2 exceeds 255 (1 byte), the data of 1 lower byte is effective.
* 0x00: No Function Error Packet header, category and function code are not included in this protocol. 0x01: Check Sum Error Check sum value of received packet is not correct. 0x02: Data Length Error Packet is correctly received, but the data size is over the upper limit. * Check Sum: If the value of a sum total of 1 and 2 exceeds 255 (1 byte), the data of 1 lower byte is effective.
2 Answer at the time of Enquiry request (Normal completion)
No. Item : : X Header Answer Value 0x70: Answer 0x00: Completed
Return Data Size 0xXX Return Data1 : : 0xXX 0xXX 0xXX
Return Data (X-3) 0xXX 0xXX

X+1 Check Sum

* 0x00: Completed Completed packet is correctly received and process is also correctly completed. * Return Data returns the read value. * Check Sum: If the value of a sum total of 1 to X exceeds 255 (1 byte), the data of 1 lower byte is effective.
3 Answer at the time of Enquiry request (Abnormal completion)
No. Item 3 Header Answer Check Sum Value 0x70: Answer 0x03: Command Canceled (Abnormal completion) 0x73
* 0x03: Command Canceled Packet is correctly received, but the data value is not correct or the request cannot be accepted in the current host state.

4. General Function

(a) Mode control
Syntax Control Enquiry Header 0x8C 0x83 Category 0x00 Function Code Table(1-a)[a] Data1 0x02 0xFF Data2 Code Table(1-a)[b] 0xFF Check Sum 0xXX 0xXX

Answer Control

Header 0x70 0x70 0x70 0x70
Answer 0x00 0x01 0x02 0x03
Check Sum 0x70 0x71 0x72 0x73 Completed Limit Over Limit Under Command Canceled

Answer Enquiry

Header 0x70

Answer 0x00

Return to Data Size 0x02
Return Data1 Code Table (1-a)[b]

Check Sum 0xXX Completed

Code Table(1-a)
[a]Function 0x00 Power*1 [b]Range/Switch Code 0x00 0x01 0x01 Input Select*2 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x20 0x02 Force Status Display 0x00 0x01 0x03 Audio Mute 0x00 0x01 0x04 Auto Status Display 0x00 0x01 0x05 Closed Caption 0x00 0x01 0x02 0x03 0x04 OFF ON INPUT2 RGB INPUT2 COMPONENT OPTION1 VIDEO OPTION1 S VIDEO OPTION1 RGB OPTION1 COMPONENT OPTION2 VIDEO OPTION2 S VIDEO OPTION2 RGB OPTION2 COMPONENT INPUT1 DVI ON OFF OFF ON ON OFF OFF CC1 CC2 CC3 CC4 Yes Yes Disable Enable Yes Yes Enable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Command Control Yes Enquiry Yes Standby Enable Power On Enable

[a]Function 0x06 Color System [b]Range/Switch Code 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x0F Language 0x00 0x01 0x02 0x03 0x04 0x05 0x10 0x13 Index Number Power Saving Auto NTSC NTSC4.43 PAL SECAM PAL-M PAL-N PAL60 Japanese English Deutsch Franais Espaol Italiano Yes Yes Yes Yes Disable Disable Enable Enable Yes Yes Disable Enable Command Control Yes Enquiry Yes Standby Disable Power On Enable
0x01 - 0xFF 0x00 0x01 Standard Reduce ON OFF 1080i 1035i DTV PC H/Comp Video OFF

Speaker Out

0x00 0x01

Disable

Enable

HD Mode

RGB Mode

Sync Mode

0x1B Clock Display
0x1B ON 0x24 Input Detect(Option1) 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 FW12(HD15) FW10(CVBS, Y/C) FW11(BNC) Reserved FW31/32 FW50 Reserved Reserved Reserved Reserved No Yes Disable Enable
0x0A Reserved 0x0B Reserved 0x0C Reserved 0x0D Reserved 0x0E Reserved (Continued)
[a]Function 0x24 0x25 Input Detect(Option1) Input Detect(Option2) [b]Range/Switch Code 0x0F Not Connect 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 FW12(HD15) FW10(CVBS, Y/C) FW11(BNC) Reserved FW31/32 FW50 Reserved Reserved Reserved Reserved Command Control No No Enquiry Yes Yes Standby Disable Disable Power On Enable Enable
0x0A Reserved 0x0B Reserved 0x0C Reserved 0x0D Reserved 0x0E Reserved 0x0F Not Connect 0x26 Auto Shut OFF 0x00 0x01 0x30 PAP*2 0x00 0x01 0x02 0x31 Active Picture 0x00 0x01 0x02 0x32 0x33 Picture Size(P&P) Sub Picture Size (PinP) OFF ON OFF P&P PinP Left(P&P)/Main(PinP) Right(P&P)/Sub(PinP) Swap*2 Yes Yes Yes Yes Disable Disable Enable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable
0x00 - 0x0E 0x00 0x01 Large Small Position1 Position2 Position3 Position4

Picture Position(PinP)*3

0x00 0x01 0x02 0x03
PAP Input Detect (Left/Main)
0x0A INPUT2 RGB 0x0B INPUT2 COMPONENT 0x0C OPTION1 VIDEO 0x0D OPTION1 S VIDEO 0x0E OPTION1 RGB 0x0F OPTION1 COMPONENT 0x10 0x11 0x12 0x13 OPTION2 VIDEO OPTION2 S VIDEO OPTION2 RGB OPTION2 COMPONENT

(Continued)

[a]Function 0x35 0x36 PAP Input Detect (Left/Main) [b]Range/Switch Code 0x20 INPUT1 DVI Command Control No No Enquiry Yes Yes Standby Disable Disable Power On Enable Enable

PAP Input Detect (Right/Sub) 0x0A INPUT2 RGB 0x0B INPUT2 COMPONENT 0x0C OPTION1 VIDEO 0x0D OPTION1 S VIDEO 0x0E OPTION1 RGB 0x0F OPTION1 COMPONENT 0x10 0x11 0x12 0x13 0x20 OPTION2 VIDEO OPTION2 S VIDEO OPTION2 RGB OPTION2 COMPONENT INPUT1 DVI
*1: Transmit the next command 10 seconds after Power On and Power Off commands are transmitted. If not, correct data may not be able to be acquired. *2: For INPUT SELECT, PAP, and Active Picture (SWAP), check the busy state using a Busy to INPUT command. *3: The Picture Position arrangement is as shown below.
[a]Function 0x43 0x44 BackLight Illumination [b]Range/Switch code 0x00 - 0x64 0x00 OFF 0x01 Low 0x02 High 0x45 Control Mode 0x00 Main+Remocon 0x01 Main 0x02 Remocon 0x46 On Off Timer Mode 0x00 Every Day 0x01 Day Of Week 0x47 On Timer Enable bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Sunday 1:Enable, 0:Disable Monday 1:Enable, 0:Disable Tuesday 1:Enable, 0:Disable Wednesday 1:Enable, 0:Disable Thursday 1:Enable, 0:Disable Friday 1:Enable, 0:Disable Saturday 1:Enable, 0:Disable Every day 1:Enable, 0:Disable*4 Yes Yes Enable Enable Yes Yes Enable Enable Yes Yes Disable Enable Command Control Yes Yes Enquiry Yes Yes Standby Disable Disable Power On Enable Enable
[a]Function 0x48 Off Timer Enable [b]Range/Switch code bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 0x65 IP Setting Mode Sunday 1:Enable, 0:Disable Monday 1:Enable, 0:Disable Tuesday 1:Enable, 0:Disable Wednesday 1:Enable, 0:Disable Thursday 1:Enable, 0:Disable Friday 1:Enable, 0:Disable Saturday 1:Enable, 0:Disable Every day 1:Enable, 0:Disable*4 Yes Yes Enable Enable Command Control Yes Enquiry Yes Standby Enable Power On Enable
0x00 DHCP 0x01 Manual 0x02 Speed

IP Setting Execute

0x00 No 0x01 Yes

IP Setting Result

0x00 Done 0x01 Error 1 (UART Commu.) 0x02 Error 2 (Duplication) 0x03 Error 3 (IP Add Setting) 0x04 Error 4 (GW Add Setting) 0x05 Error 5 (DNS1 Setting) 0x06 Error 6 (DNS2 Setting) 0x07 Error 7 (Sbnt Msk Setting)

Speed Setting

0x00 100Mbps/Full Duplex 0x01 100Mbps/Half Duplex 0x02 10Mbps/Full Duplex 0x03 10Mbps/Half Duplex 0x04 Auto
*4: For every day, all bits should be put in the same state. (Enable:0xff, Disable:0x00)

(b) Color matrix

Syntax Header Category Control 0x8C 0x00 Function Code Table (1-b)[a] Data1 0x04 Data2 Code Table (1-c) Data3 Code Table (1-b)[b] Data3 Check Sum

Code Table (1-d) 0xXX

Syntax Enquiry

Header 0x83

Category 0x00
Function Code Table(1-b)[a]

Data1 Code Table (1-c)

Data2 Code Table (1-d)

Check Sum 0xXX

Header 0x70 0x70

Answer 0x00 0x03

Check Sum 0x70 0x73 Completed Command Canceled

Answer Header Enquiry

Answer Return to Data Size 0x00 0x04

Return Data1

Return Data2

Return Data3

Check Sum Completed
Code Table (1-c) Code Table (1-b)[b] Code Table(1-d) 0xXX

Code Table(1-b)

[a]Function 0x1D Color Matrix [b]Range/Switch code 0x00 YCbCr 0x01 YPbPr Command Control Yes Enquiry Yes Standby Disable Power On Enable

Code Table(1-c)

Format Select 0x00 0x01 0x02 0x03 480p 1080i 720p 480i

Code Table(1-d)

Input Select 0x00 0x01 0x02 Input2 Option1 Option2 (Invalid for FWD-32LX1R)
(c) Time control Clock Set (Hour, Minute)
Syntax Control Header 0x8C Category 0x00 Function 0x22 Data1 0x03 Data2 Hour:0x00 - 0x17 Data3 Minute:0x00 - 0x3B Check Sum 0xXX

Function 0x22

Data1 0xFF

Data2 0xFF

Check Sum 0xA3

Return to Data Size 0x03

Return Data1 Hour:0x00 - 0x17*
Return Data2 Minute:0x00 - 0x3B
* Data of Hour: 0x80 and Minute: 0x00 is set as Return Data when a timer is not set after factory setting.

Clock Set (Week)

Syntax Control Header 0x8C Category 0x00 Function 0x23 Data1 0x02 Data2 Week:Code Table(1-e) Check Sum 0xXX

Function 0x23

Check Sum 0xA4
Return Data1 Week:Code Table(1-e)

Code Table(1-e)

Week Select 0x00 0x01 0x02 0x03 0x04 0x05 0x06 Sunday Monday Tuesday Wednesday Thursday Friday Saturday

On Timer, Off Timer

Syntax Control Header 0x8C Category 0x00 Function Code Table(1-f)[a] Data1 0x03 Data2 Hour:0x00 - 0x17 Data3 Minute:0x00 - 0x3B Check Sum 0xXX
Function Code Table(1-f)[a]
Return Data1 Hour:0x00 - 0x17
Return Data2 Minut:0x00 - 0x3B

Code Table(1-f)

[a]Function Clock Set 0x22 0x23 On Timer 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 Off Timer 0x58 0x59 0x5A 0x5B 0x5C 0x5D 0x5E 0x5F Sunday Monday Tuesday Wednesday Thursday Friday Saturday Every day Yes Yes Disable Enable Sunday Monday Tuesday Wednesday Thursday Friday Saturday Every day Yes Yes Disable Enable Hour, Minute Week Yes Yes Disable Enable [b]Range/Switch code Command Control Enquiry Standby Power On
(d) IP Address Setting IP Address
Syntax Control Header 0x8C Category 0x00 Function 0x42 Data1 0x05 Data2 Address 0 0x00 - 0xFF Data3 Address 1 0x00 - 0xFF Data4 Address 2 0x00 - 0xFF Data5 Address 3 0x00 - 0xFF Check Sum 0xXX

Subnet Mask

Syntax Control Header 0x8C Category 0x00 Function 0x61 Data1 0x05 Data2 Address 0 0x00 - 0xFF Data3 Address 1 0x00 - 0xFF Data4 Address 2 0x00 - 0xFF Data5 Address 3 0x00 - 0xFF Check Sum 0xXX

Gateway Address

Syntax Control Header 0x8C Category 0x00 Function 0x62 Data1 0x05 Data2 Address 0 0x00 - 0xFF Data3 Address 1 0x00 - 0xFF Data4 Address 2 0x00 - 0xFF Data5 Address 3 0x00 - 0xFF Check Sum 0xXX

DNS Primary

Syntax Control Header 0x8C Category 0x00 Function 0x63 Data1 0x05 Data2 Address 0 0x00 - 0xFF Data3 Address 1 0x00 - 0xFF Data4 Address 2 0x00 - 0xFF Data5 Address 3 0x00 - 0xFF Check Sum 0xXX

DNS Secondary

Syntax Control Header 0x8C Category 0x00 Function 0x64 Data1 0x05 Data2 Address 0 0x00 - 0xFF Data3 Address 1 0x00 - 0xFF Data4 Address 2 0x00 - 0xFF Data5 Address 3 0x00 - 0xFF Check Sum 0xXX
Example of IP Address 192.128.14.(0xC0) Address (0x80) Address (0x0E) Address (0x01) Address 3 * IP Address command can be carried out even in the standby state.
[a]Function 0x42 0x61 0x62 0x63 0x64 IP Address Subnet Mask Gateway Address DNS Primary DNS Secondary [b]Range/Switch code Command Control Yes Enquiry Yes Standby Enable Power On Enable

5. Picture/Sound

(a) Picture/Sound
Syntax Control Enquiry Header 0x8C 0x83 Category 0x10 Function Code Table(2-a)[a] Data1 0x02 0xFF Data2 Code Table(2-a)[b] 0xFF Check Sum 0xXX 0xXX
Return Data1 Code Table(2-a)[b]

Code Table(2-a)

[a]Function 0x00 0x01 0x02 0x03 0x04 Contrast Brightness Chroma Phase Color Temp [b]Range/Switch code 0x00 - 0x64* 0x00 - 0x64* 0x00 - 0x64 0x00 - 0x64 0x00 0x01 0x02 0x03 0x04 0x05 0x09 0x0A Sharpness NR 0x00 - 0x0A 0x00 0x01 0x02 0x03 0x0B Cinema Drive 0x00 0x01 0x0C Dynamic Picture 0x00 0x01 0x02 0x0D Color Correct 0x00 0x01 0x0E Gamma Correct 0x00 0x01 0x02 0x10 Picture Mode 0x00 0x01 0x02 0x03 0x04 0x30 0x31 0x32 0x33 0x34 Volume Treble Bass Balance Surround 0x00 - 0x64 0x00 - 0x64 0x00 - 0x64 0x00 - 0x64 0x00 0x01 0x02 OFF Hall Simulate OFF Low Mid High Auto OFF OFF Low High ON OFF High Mid Low Standard Vivid User1 User2 User3 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Enable Disable Disable Disable Disable Enable Enable Enable Enable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Cool Neutral Warm Color1 Color2 Color3 Yes Yes Yes Yes Disable Disable Enable Enable Command Control Yes Yes Yes Yes Yes Enquiry Yes Yes Yes Yes Yes Standby Disable Disable Disable Disable Disable Power On Enable Enable Enable Enable Enable
*: The setting value during two-screen display is as follows: Contrast: Setting value 12 during one-screen display Brightness: Setting value 24 during one-screen display

(b) Color temperature

Syntax Control Header 0x8C Category 0x10 Function Code Table(2-b)[a] Data1 0x03 Data2 Code Table(2-c) Data3 Code Table(2-b)[b] Check Sum 0xXX

Category 0x10

Function Code Table(2-b)[a]

Data1 Code Table(2-c)

Return Data1 Code Table(2-c)
Return Data2 Code Table(2-b)[b]

Code Table(2-b)

[a]Function 0x05 0x06 0x07 Red Gain Green Gain Blue Gain [b]Range/Switch code 0x00 - 0x0A 0x00 - 0x0A 0x00 - 0x0A Command Control Yes Enquiry Yes Standby Disable Power On Enable

Code Table(2-c)

Format Select 0x03 0x04 0x05 Color1 Color2 Color3

6. Size/Shift

(a) 8 bit register
Syntax Control Enquiry Header 0x8C 0x83 Category 0x20 Function Code Table(3-b)[a] Data1 0x02 0xFF Data2 Code Table(3-b)[b] 0xFF Check Sum 0xXX 0xXX
Return Data1 Code Table(3-b)[b]

Code Table(3-b)

[a]Function 0x00 0x01 0x02 0x03 0x04 H Size H Center V Size V Center Aspect [b]Range/Switch code 0x00 - 0x64 0x00 - 0x64 0x00 - 0x64 0x00 - 0x64 0x00 0x01 0x02 0x03 0x04 0x05 Multi Display 0x00 0x01 0x02 0x03 0x07 0x08 Dot Phase Auto Wide 0x00 - 0x1F 0x00 0x01 0x09 4:3 Mode 0x00 0x01 0x0B Multi Position(x2)* 0x00 0x01 0x02 0x03 0x0C Multi Position(x3)* 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x0D Multi Position(x4)* 0x00 0x01 0x02 0x03 0x04 0x05 0x06 OFF ON Normal Wide Zoom Position1 Position2 Position3 Position4 Position1 Position2 Position3 Position4 Position5 Position6 Position7 Position8 Position9 Position1 Position2 Position3 Position4 Position5 Position6 Position7 Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Yes Yes Disable Enable Wide Zoom Zoom Full Sub Title Normal OFF x2 x3 x4 Yes Yes Yes Yes Disable Disable Enable Enable Yes Yes Disable Enable Command Control Yes Yes Yes Yes Yes Enquiry Yes Yes Yes Yes Yes Standby Disable Disable Disable Disable Disable Power On Enable Enable Enable Enable Enable
[a]Function 0x0D Multi Position(x4)* [b]Range/Switch code 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F
*: The Multi Position arrangement is as shown below.

Command Control Yes

Enquiry Yes

Standby Disable

Power On Enable
Position8 Position9 Position10 Position11 Position12 Position13 Position14 Position15 Position16

Multi Position(x2)

Multi Position(x3)

Multi Position(x4)

7. Status Enquiry

(a) Model name enquiry

Syntax Enquiry Header 0x83 Category 0x30 Function 0x00 (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xB1
Return Data1 Code Table(4-a)

Code Table(4-a)

Format Select 0x0A 0x0B FWD-40LX1 FWD-32LX1R
(b) Serial number enquiry

Syntax Enquiry Header 0x83 Category 0x30 Function 0x01 (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xB2
Answer Header Enquiry 0x70

Return to Data Size 0x05

Return Data1 Upper 8bit Data
Return Data2 Middle Upper Data
Return Data3 Return Data4 Check Sum Middle Lower Data Lower 8bit Data 0xXX Completed
Return Data1-Data4: 0x001E8480 - 0x002DC6BF(2,000,000 - 2,999,999)
(c) Operating time enquiry
Syntax Enquiry Header 0x83 Category 0x30 Function 0x02 (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xB3
Return Data1-Data4: 0x00000000 - 0xD693A3FF(0sec._3,599,999,999sec.)
(d) Software version enquiry (Main CPU)
Syntax Enquiry Header 0x83 Category 0x30 Function 0x03 (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xB4
Return Data2 Lower 8bit Data
Return Data1-Data2: 0x0000 - 0xFFFF Example) For version 1.000, they become 10 and 00, respectively.
(e) 8 bit register enquiry
Syntax Enquiry Header 0x83 Category 0x30 Function Data1 Data2 0xFF Check Sum 0xXX

Code Table(4-b)[a] 0xFF

Return Data1 Code Table(4-b)[b]

Code Table(4-b)

[a]Function 0x07 0x09 0x0A 0x0D 0x10 0x20 Digital 3.3 V Digital 5 V Temp1 Temp(P/S) Analog5 V/9 V Busy to Input [b]Return Data 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF 0x00: Not Busy 0x01: Busy 5 V power output Unit
(f) Software version enquiry (Scaler)
Syntax Enquiry Header 0x83 Category 0x30 Function 0x0F (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xC0
Return Data1 - Data2: 0x0000 - 0xFFFF Example) For version 1.000, they become 10 and 00, respectively.

(g) Shutdown Log enquiry

Syntax Enquiry Header 0x83 Category 0x30 Function 0x11 (Code Table(4-d)[a]) Data1 0xFF Data2 0xFF Check Sum 0xC2
Return Data1 Code Table(4-c)
Return Data1: 0x00 - 0xFF

Code Table(4-c)

Shutdown Information bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Reserved 1: FAN operation is abnormal 1: Backlight is abnormal 1: Temperature sensor is abnormal 1: Main power supply is abnormal 0: Normal 0: Normal 0: Normal 0: Normal

1: Digital power supply is abnormal (3.3 V, 5 V) 0: Normal 1: Analog supply is abnormal (5 V/9 V) 1: Scaler is abnormal 0: Normal 0: Normal

Code Table(4-d)

[a]Function 0x00 0x01 0x02 0x03 0x07 0x09 0x0A 0x0D 0x0F 0x10
[b]Range/Switch code 0x0A - 0x0B 0x001E8480 - 0x002DC6BF (2,000,000 - 2,999,999) 0x00000000 - 0xD693A3FF (0sec._3,599,999,999sec.) 0x0000 - 0xFFFF 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF 0x0000 - 0xFFFF 0x00 - 0xFF

Command Control No Yes

Enquiry Yes Yes

Standby Enable Enable

Power On Enable Enable
Model Name Serial Number Operation Time Soft Version(Main) Digital 3.3 V Digital 5 V Temp1 Temp(P/S) Soft Version(Scaler) Analog5 V/9 V
[a]Function 0x11 0x12 0x13 0x14 0x20 Shutdown Log Digital 3.3 V(Failure) Digital 5 V(Failure) [b]Range/Switch code 0x00 - 0xFF 0x00 - 0xFF 0x00 - 0xFF Command Control No Enquiry Yes Standby Enable Power On Enable
Analog5 V/9 V(Failure) 0x00 - 0xFF Busy to INPUT* 0x00 Non Busy 0x01 Busy
* Busy to INPUT should be judged by Busy Non Busy. Busy to INPUT may be incorrectly judged during start when it is judged by only Non Busy.

8. User Reset

Syntax Control Header 0x8C Category 0x50 Function Code Table(5) Data1 0x02 Data2 0xFF Check Sum 0xXX

Code Table(5)

Function 0x00 0x01 0x03 0x04 Picture Reset Audio Reset Picture Reset2 All Reset Contrast, Brightness, Chroma, Phase Range/Switch code Command Control Yes Enquiry No Standby Disable Power On Enable
The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
Le matriel contenu dans ce manuel consiste en informations qui sont la proprit de Sony Corporation. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des oprations ou entretiens de lquipement moins dune permission crite de Sony Corporation.

FWD-40LX1

LCD Pro Display - Crystal Bezel / Matte Bezel
Key Features WEGA Engine system High Resolution Panel - 1366 x 768 WXGA Burn-in resistant LCD technology Networking and Tuner Options Crystal Coated or Matte Bezel
Shown with optional speakers.
Key Technologies Exceptional LCD performance High brightness, superior contrast and super-fast 16 ms video response time
combine to deliver crisp, clear text and smooth motion images for video applications.
WEGA Engine system Intelligent digital processing system delivers superb picture quality by minimizing
signal deterioration caused by digital-to-analog conversion.
Cost of Ownership Burn-in resistant LCD technology ensures long life when using static images. Low power
consumption and long-life panel delivers hours of use to keep your total cost of ownership low.
Upscale style Scratch-resistant crystal-look bezel in a choice of three elegant colors including pearl white adds
upscale refinement to any interior. A matte finished bezel is also available. Cable management system conceals wires and cables, keeping the back looking streamlined and uncluttered.
Networking options Optional network cards and boxes (sold separately) let you centrally control, deliver and
troubleshoot digital content across a standard IP network to one or hundreds of networked displays. Reduce labor and production costs associated with managing individual content.
Shown with optional stand and speakers.

Features

Picture Modes: Custom (3), Vivid, Standard Color Temperature: Cool, Neutral, Warm Panel Type: a-Si-TFT Active Matrix LCD Panel Screen or Display Technology: LCD Video Processing: WEGA Engine Technology Composite Video Input(s): 1 (Side) Control-S Input(s): 1 (Side) Control-S Output(s): 1 (Side) Dual Option Slot: Yes RCA Audio Input(s): RCA (L/R) RF Connection Input(s): 1 (optional) RS232 Control: 1 (Side) S-Video Input(s): 1 (Side) S-Video Output(s): 1 (Side) Video In (BNC): 1 (optional)

Optional Accessories

Networking: NSP-1 (Digital Signage Player), NSP100 (Network Video Player), EBS-N200 (Status Control and Streaming realtime video sent over IP with connectivity to PJNet), BKMFW32 (Internal Network Management Device for status and control over IP), ICS-SP20 (TV Tuner and Hospitality System) Stationary Wall Mount Kit supports Landscape mode (SFM1). Wall Mount Kit supporting Portait, Landscape and Tilt (up to 15 degrees). Also, allows room for EBS accessories (PLP-91/D). Input Boards: BKM-FW11 (Component/RGB Input Adapter), BKM-FW12 (RGB Component Loop Through) Speakers: SS-SP40FW/B, SS-SP40FW/S (Speakers for Black and Silver models), SS-SP40FW/W (Speakers for White Model) Software: PJNet (Asset Management tool to control up to 255 Sony Plasmas or Projectors), DCDS (Asset Management tool to schedule and control up to 10,000 points) Color: Crystal Black (FWD-40LX1/B), Crystal Silver (FWD-40LX/S), Crystal White (FWD40LX1/W), Matte Black (FWD-40LX1/BI), Matte Silver (FWD-40LX1/SI)
2005 Sony Electronics Inc. Features and specifications are subject to change without notice. Nonmetric weights and measures are approximate. Sony is a trademark of Sony. All other trademarks are property of their respective owners.

Convenience

Multiple Language Display: English, French, Spanish, Italian, German, Japanese, Dutch, Swedish, Russian, Chinese Picture and Picture: Yes Picture-in-Picture: Yes HDMI Technology: Yes (Video thru DVID and Audio thru RCA)
Internal Power Supply: Yes Power Consumption: 220W (typical) Power Requirements: 100V - 240V AC, 50-60Hz
Regulation and Standard Compliance
Emissions/Ergonomics: N/A Energy Star Compliant: N/A Plug & Play: N/A Safety Regulations: Ul1950, CSA No.950 (c-UL), CE LVD (EN60950), FCC Class B, VCCI Class B, CE EMC (EN55022 Class B, EN61000-3-2, EN61000-3-3), C-Tick (AS/NZS 3548/95, AS/NZS 4252.1), CCIB, JEIDA, CB, KTL, MIC

Specifications

General
Screen Size: 40.0" Color: Crystal Black (FWD-40LX1/B), Crystal Silver (FWD-40LX/S), Crystal White (FWD40LX1/W), Matte Black (FWD-40LX1/BI), Matte Silver (FWD-40LX1/SI)
Horizontal Scan (KHz) for PC: N/A Closed Caption Decoder: Yes Contrast Ratio: N/A Display Resolution: 1366 x 768 Display Response Time: 8 ms Image Retention Protection: Auto Wide Mode, Multi-Mode Picture Orbit, Picture Inversion, Power Save, Smart Fan Technology, Timers, White Screen Viewing Angle: Horizontal: 178 Vertical: 178 ,
Service and Warranty Information
Extended Warranty: Optional Plans for up to 5 years on-site, or 3 years depot service Limited Warranty: 2 years parts, 2 years labor, 1 year panel

Dimensions

Weight: 60.5 lbs Measurements: 39.3 x 23.5 x 4.9 inches

Operating Conditions

Colors: 16.7 million Luminance: TBD Pixel Pitch: 0.648 x 0.648mm Screen Treatment: Anti-Glare, Anti-Reflective Vertical Refresh Range: N/A
Audio Power Output: 14W Total (7Wx2 Digital AMP)
Cable Management System: Yes On Screen Controls: Yes Wall/Arm Mount: Yes

Software

Operating System Compatibility: N/A

Hardware

Color Systems: NTSC, PAL, SECAM, NTSC4.43, PAL60, PAL-M, PAL-N Mount Design: Landscape, Portrait Remote Control: Multi-Function Remote

Inputs and Outputs

Analog Audio Input(s): 1 (Side) Analog Audio Output(s): Speakers (L/R) Optional Analog Video Input(s): 1 (Side) DVI Connection Input(s): 1 (Side) PC Audio Input(s): 1 (per input) PC Video Input(s): 2 (1-DVI-D, 1-HD15) Component Video (Y/Pb/Pr ) Input(s): 1 (Side) Optional

Supplied Accessories

AC Power Cord, Operating Instructions, AC Plug Holder (2), AA/R6 Size Battery (2), Cable Holder (4), Remote Control
Please visit the Dealer Network for current information at www.sony.com/dn
Sony Electronics Inc. 16530 Via Esprillo San Diego, CA 92127 800.222.7669 www.sony.com

Last Updated: 08/04/2006