For customers using Windows 95
Install the new model information from the Windows 95 Monitor Information Disk into your PC. (To install the file, refer to the attached About the Windows 95 Monitor Information Disk/File.) This monitor complies with the VESA DDC Plug&Play standard. If your PC/graphics board complies with DDC, select Plug and Play Monitor (VESA DDC) as Monitor type from Control Panel in Windows 95. Some PCs/graphics boards do not comply with DDC. Even if your computer complies with DDC, it may have some problems connecting with this monitor. In this case, select this monitors model name (GDM-500PS) as Monitor type in Windows 95.

EN F ES C

This monitor has two modes of input signal selection, AUTO and MANUAL. When AUTO is selected If no signal is input from the selected connector, the monitor automatically selects the other connectors signal. When you restart the computer you want to view, or that computer is in power saving mode, the monitor may automatically select the other connectors signal. This is because the monitor switches from the interrupted signal to the constant signal. If this happens, manually select the desired signal using the INPUT button. When MANUAL is selected Even if no signal is input from the selected connector, the monitor does not select the other connectors signal.
Press the >?// buttons to select AUTO or MANUAL.
The OPTION OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. For more information on using the OSD, see Introducing the On-screen Display System on page 9.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 is different from Windows 95 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors.
Selecting the On-screen Display Language
If you need to change the OSD language, see Using the LANG (Language) On-screen Display on page 17. The default setting is English.
Press the MENU button. The MENU OSD appears.

COLOR GEOM LANG

CENTER SCREEN EXIT SIZE ZOOM OPTION

Customizing Your Monitor

Before adjusting Connect the monitor and the computer, and turn them on. Select LANG in the MENU OSD, then select ENGLISH (English) (see page 17).
Getting Started Customizing Your Monitor
Introducing the On-screen Display System
Most adjustments are made using the MENU OSD.
Using the CENTER On-screen Display
The CENTER settings allow you to adjust the centering of the picture. Once the setting is adjusted, it will be stored in memory for the current input signal.
Using the SIZE On-screen Display
The SIZE settings allow you to adjust the size of the picture. Once the setting is adjusted, it will be stored in memory for the current input signal.
Adjusting the Picture Brightness and Contrast

Once the setting is adjusted, it will be stored in memory for all input signals received.

MENU OSD

Press the MENU button to display the MENU OSD. This MENU OSD contains links to the other OSDs described below.
Press the (brightness)./> or > (contrast) ?// buttons. The BRIGHTNESS/CONTRAST OSD appears.

BRIGHTNESS/CONTRAST

COLOR GEOM
Press the./> and >?// buttons to select CENTER, and press the MENU button again. The CENTER OSD appears.

CENTER

Press the./> and >?// buttons to select SIZE, and press the MENU button again. The SIZE OSD appears.

80.0kHz/ 75Hz

Horizontal Frequency*

Vertical Frequency*

1 COLOR
Displays the COLOR OSD for adjusting the color temperature.
For brightness adjustment Press the./> buttons.
For horizontal adjustment Press the >?// buttons.
>. for more brightness. for less brightness
Displays the CENTER OSD for adjusting the centering of the picture.
/. to increase picture size ?. to decrease picture size
/. to move the picture right ?. to move the picture left
For contrast adjustment Press the >?// buttons.

SCREEN

Displays the SCREEN OSD for adjusting the vertical and horizontal convergence, etc. For vertical adjustment Press the./> buttons.
For vertical adjustment Press the./> buttons.
/. for more contrast ?. for less contrast
Displays the ZOOM OSD for enlarging and reducing the picture. >. to move the picture up. to move the picture down
>. to increase picture size. to decrease picture size
The OSD automatically disappears after about 3 seconds. To reset, press the RESET button while the OSD is on. The brightness and contrast are both reset to the factory settings.
The horizontal and vertical frequencies for the received input signal appear in the BRIGHTNESS/CONTRAST OSD.
Displays the OPTION OSD for adjusting the OSD position and degaussing the screen, etc.
The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset, press the RESET button while the OSD is on. The horizontal and vertical sizes are both reset to the factory settings.
Displays the SIZE OSD for adjusting the picture size.
The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset, press the RESET button while the OSD is on. The horizontal and vertical centerings are both reset to the factory settings.
Displays the LANGUAGE OSD for selecting the language.
Displays the GEOMETRY OSD for adjusting the picture rotation and pincushion, etc.

9 EXIT

Closes the MENU OSD.
Using the GEOM (Geometry) Onscreen Display
The GEOM (geometry) settings allow you to adjust the shape and orientation of the picture. Once the rotation is adjusted, it will be stored in memory for all input signals received. All other adjustments will be stored in memory for the current input signal.

Press the >?// buttons to adjust the settings.
Using the ZOOM On-screen Display
The ZOOM settings allow you to enlarge or reduce the picture. Once the setting is adjusted, it will be stored in memory for the current input signal.
Using the COLOR On-screen Display
You can change the monitors color temperature. For example, you can adjust or change the colors of a picture on the screen to match the actual colors of the printed picture. Once the setting is adjusted, it will be stored in memory for all input signals received.

ROTATION

/. to rotate the picture clockwise
?. to rotate the picture counterclockwise

PINCUSHION

/. to expand the picture sides
Press the./> and >?// buttons to select GEOM, and press the MENU button again. The GEOMETRY OSD appears.

GEOMETRY

?. to contract the picture sides
Press the./> and >?// buttons to select ZOOM, and press the MENU button again. The ZOOM OSD appears.
Press the./> and >?// buttons to select COLOR, and press the MENU button again. The COLOR OSD appears.
COLOR 5000K 6500K 9300K 50 50

PIN BALANCE

/. to move the picture sides to the right

H V 26 73

26 ROTATION
?. to move the picture sides to the left

R G B R G B

B I AS B I AS B I AS GAIN GAIN GAIN
Press the./> buttons to select the item you want to adjust. Select
ROTATION PINCUSHION PIN BALANCE KEYSTONE KEY BALANCE
Press the >?//buttons to adjust the picture zoom.

KEYSTONE

/. to increase the picture width at the top
/. to enlarge the picture ?. to reduce the picture
Press the >?// buttons to select the color temperature.
?. to decrease the picture width at the top
The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To
adjust the picture rotation adjust the picture sides adjust the picture side balance adjust the picture width adjust the picture shape balance KEY BALANCE /. to move the top of the picture to the right
To reset, press the RESET button while the OSD is on. Note
There are three color temperature modes in the OSD. The preset adjustments are: 5000K, 6500K, 9300K

/. to turn CANCEL MOIRE ON CANCEL MOIRE

OFF ON

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset, press the RESET button while the OSD is on. The selected item is reset to the factory settings.
Press the./> and >?// buttons to select SCREEN, and press the MENU button again. The SCREEN OSD appears.
?. to turn CANCEL MOIRE OFF

EN F ES

ADJ MOIRE ADJUST
/ or ?. to adjust the screen until the moire is at a minimum

TOP BOT 26 ADJ

The picture may become fuzzy when CANCEL MOIRE is set to ON.
H CONVERGENCE V CONVERGENCE TOP V CONVER TOP BOT V CONVER BOTTOM

H CONVERGENCE

Press the./> buttons to select the item you want to adjust.
/. to shift red shadows to the right and blue shadows to the left H CONVERGENCE
?. to shift red shadows to the left and blue shadows to the right
adjust the horizontal convergence V CONVERGENCE adjust the vertical convergence
/. to shift red shadows up and blue shadows down
?. to shift red shadows down and blue shadows up
adjust the screens upper vertical convergence TOP adjust the screens lower vertical convergence V CONVER TOP /. to shift red shadows up and blue shadows down

(continued)

Customizing Your Monitor Setting the power saving delay time
You can set the delay time before the monitor enters the power saving mode. See page 19 for more information on this monitors power saving capabilities.
Using the OPTION On-screen Display
The OPTION OSD allows you to manually degauss the screen and adjust settings such as the OSD position and power saving delay time. It also allows you to lock the controls.
Changing the on-screen display position
You can change the OSD position (for example, when you want to adjust the picture behind the OSD).

Locking the controls

The control lock function disables all of the buttons on the front panel except the u (power) switch, MENU and INPUT buttons.

Degaussing the screen

The monitor screen is automatically degaussed (demagnetized) when the power is turned on. You can also manually degauss the monitor.
Press the./> buttons to select (OSD H POSITION) or (OSD V POSITION). Select (OSD H POSITION) to adjust the horizontal position.

F ES C

Press the./> buttons to select DELAY).

(PWR SAVE

Press the./> buttons to select LOCK).

(CONTROL

AUTO 5 SEC 60 MIN 1 MIN OFF

UNLOCK LOCK CONTROL LOCK

PWR SAVE DELAY
Press the./> buttons to select DEGAUSS).

(MANUAL Select position.

OSD H POSITION
(OSD V POSITION) to adjust the vertical

OPTION AUTO

Press the >?// buttons to select the desired time.
Press the >?// buttons to select LOCK.
Press the > / button. The screen is degaussed for about 3 seconds.

UNLOCK OSD V POSITION

When PWR SAVE DELAY is set to OFF, the monitor does not go into power saving mode. The OPTION OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset, press the RESET button while the OSD is on.
The OPTION OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. Once you select LOCK, you cannot select any items except EXIT and OPTION in the MENU OSD. If you press any button other than the u (power) switch, MENU and INPUT buttons, the mark appears on the screen.
Press the >?// buttons to move the OSD to the desired position.
If you need to degauss the screen a second time, wait for at least 20 minutes before repeating the steps above. The OPTION OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. The OPTION OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset, press the RESET button while the OSD is on.
To cancel the control lock
Repeat steps 1 through 3 above and press the >?// buttons to select UNLOCK.

Technical Features

Using the LANG (Language) Onscreen Display
English, French, German, Spanish, Italian and Japanese versions of the OSDs are available.
Resetting the Adjustments
Resetting an adjustment item 1
Press the MENU,./> and >?//buttons to select the OSD containing the item you want to reset.

Preset and User Modes

This monitor has factory preset modes for the 27 most popular industry standards for true plug and play compatibility. When a new input signal is entered, the monitor selects the appropriate factory preset mode and momentarily adjusts the phase calibration to provide a high quality picture to the center of the screen. The calibration is stored in memory and is immediately recalled whenever the same input signal is received. Resolution Horizontal Vertical No. (dots lines) Frequency Frequency Graphics Mode

ENGLISH: English, FRANAIS: French, DEUTSCH: German, ESPAOL: Spanish, ITALIANO: Italian, or : Japanese. The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again. To reset to English, press the RESET button while the OSD is on.
When there is no OSD displayed, press the RESET button. All of the adjustments data for the current input signal is reset to the factory settings. Note that adjustment data not affected by changes in input signal (OSD language, OSD position, input signal selection, power saving delay time and the control lock function) is not reset to the factory settings.
48.4 kHz 56.5 kHz 60.0 kHz 60.2 kHz

60 Hz 70 Hz 75 Hz 75 Hz

Click the Start button and point to Settings. Then double-click the Control Panel. Double-click the Display icon. Click Settings. Click the Color palette. Point to the desired color number and click. Point to the Desktop area and drag the slider to the desired resolution. Click OK.
68.7 kHz 67.5 kHz 68.7 kHz

85 Hz 75 Hz 75 Hz

60.0 kHz 85.9 kHz 64.0 kHz 80.0 kHz 91.1 kHz 75.0 kHz 81.3 kHz 87.5 kHz 93.8 kHz 106.3 kHz
60 Hz 85 Hz 60 Hz 75 Hz 85 Hz 60 Hz 65 Hz 70 Hz 75 Hz 85 Hz
Resetting all of the adjustment data for all input signals
Press and hold the RESET button for more than two seconds. All of the adjustment data, including the brightness and contrast, is reset to the factory settings.
Some settings may require that the computer be turned off then back on to take effect. In this case, follow the on-screen instructions.

About the color number

The Color palette setting and the actual number of colors is as follows: High Color (16 bit) n 65,536 colors True Color (24 bit) n about 1,677 million colors In True color mode (24 bit), speed may be slower. The color number may vary according to your computer or video board.

Additional Information

Getting StartedInformation Additional
1 The input signal condition
OUT OF SCAN RANGE indicates that the input signal is not supported by the monitors specifications. NO INPUT SIGNAL indicates that no signal is input, or the input signal from the selected input connector is not received. Symptom

CN503 7P WHT :S-MICRO

CN507 2P WHT :VH

-COM, DEFLECTION
CN508 9P WHT :VH CN512 9P WHT :S-MICRO

CN901 5P WHT :S-MICRO

HCENT H HCENT N HCENT L +200V +200V NC +80V GND +15V GND -15V

CN504 5P WHT :S-MICRO

H CENT H H CENT N H CENT L +200V +200V NC +80V GND +15V GND -15V

CN673 5P WHT :S-MICRO

CN672 9P WHT :S-MICRO CN605 3P

CN891 3P WHT :VH

Common Diode Anode Diode Cathode Common Anode Diode Cathode

POWER SW

AC L OUT NC AC L IN

(POWER SUPPLY)

CN610 10P B-TO-B
1 GND 2 GND 3 DRIVE I SENCE VCC V SENCE 6 L SENCE 7 AC SENCE OVP 10 LVP 9 10

(POWER SW)

Common Anode Anode

Common Diode Anode Anode

ROTATION H.STA V.STA
1 IK DET 2 HV ADJ 3 X RAY DET 4 1ST IK PROT 5 GND
LED0 LED1 CONT VR BRT VR KEY_DET D GND STBY+5V ANV_DRI D GND
GND H CONV V CONV VX VY GND
+15V GND -15V GND LCC_RB LCC_RT LCC_LB LCC_LT LCC_NS

LUMI STBY+5 GND

USB_TX USB_RX GND

AC L NC AC N

DGC NC NC DGC
ROTATION+ ROTATIONH STAT+ H STATV STATV STAT+

CN501 9P YEL :S-MICRO

CN514 3P WHT :S-MICRO

CN510 3P WHT :S-MICRO

DGC POWER HTR_SW STBY 8V GND
DGUS SW POWER SW HEATER SW STBY+8V GND
CN603 4P WHT :VH CN604 3P WHT :VH
GND GND DRIVE I SENCE VCC V SENCE L SENCE AC SENCE OVP LVP
Common Diode Cathode Diode Cathode Common Cathode Anode Anode Cathode Drain Cathode Cathode Anode Anode Source Gate

G D G S S D

CN7501 10P B-TO-B

(POWER SENSOR)

Diode Transistor (FET) Transistor (FET) Transistor (FET) Transistor Discrete semiconductot
B-SS3414<U/C>-KESSENZU-05 FASTEN
1 LEDLEDLEDLED3 KEY_DET D GND STBY+5V 7 TEMP_DRI GND 10 GND 11 GND 9

(CRT SHIELD)

+15V GND -15V GND LCC-RB LCC-RT LCC-LB LCC-LT LCC-NS

CN801 11P WHT :S-MICRO L

Source Gate Source Drain Gate Emitter Collector Base

D G G S

LCC-LT

LCC-LB

LCC-RT

LCC-RB

STAT+ STATSTAT+ STAT-

LCC-NS

CN5002 6P LCC-LT(+) WHT :S-MICRO LCC-LT(-)

CN5001 9P WHT :S-MICRO

LCC-LB(+) CN5003 LCC-LB(-) 10P WHT LCC-RT(+) :S-MICRO LCC-RT(-) LCC-RB(+) LCC-RB(-) LCC-NS(+) LCC-NS(-)
V.STAT,H.STAT, LCC,GEO, MAGNETIC SENSOR

CN5004 4P WHT :VH

(USER CONTROL)

G Board

D680, R687,
(Chip semiconductors that are not actually used are included.)

Ver.1.5

D Board
IC901, D904, D907, D908, R011, R908, R909, R921, R925, R926, R929, R930, T902 Mounted D board

D913 UDZ-12B

PIN_FB

R041 4.7k :CHIP

C025 1
R043 4.7k :CHIP R941 10k :CHIP

D907 UDZ-TE-17-12B

D904 MA111

L002 100H

R921 5.1k :RN-CP

PS502 2.0A

PS503 2.0A

D908 UDZ-TE-17-12B

1 IK DET 2 HV ADJ X RAY DET 3

5-13 5-14

1ST IK PROT GND

TO G BOARD CN671

R507 4.7k :CHIP R027 10k :CHIP

R582 10k :CHIP

R525 C523 18k :RN-CP 0.01 :PT

R1/2W :RN

T503 :HST
R039 1k :CHIP R040 1k :CHIP

RXD TXD

STBY5V R026 10k :CHIP

Q504 2SC2412K H DRIVE

C506 0.22 :MPS

Q503 2SA1036K PIN DRIVE

C508 0.022 B:CHIP

Q506 2SC3746 H DRIVE

C510 0.0047 :PT C544 0.0047 :PT R1W :RS
C554 R583 0.1 12k 25V :RN-CP B:CHIP R511 2.2 10W :RN

R581 10k :CHIP

C555 R580 0.022 10k B:CHIP :CHIP
Q517 2SA1037K PIN AMP D509 1SS119

R585 22k :CHIP

GND V.DY C V.DY H NC H.DY C H.DY C NC NC H.DY H H.DY H

T504 2.0MH HCC

Q661 Q701

Q703 Q704 Q705 Q706 Q707

Q703 2SC2459-GR H DF OUT Q704 2SC3421 H DF OUT D713 1SS119
R737 0.47 :FPRD R738 0.47 :FPRD

L701 100H R741 12k

R739 1SS:FPRD D715

1SS119

Q701 2SC2362KG H DF OUT

R743 1k :CHIP

Q706 2SA1358 H DF OUT

Q708 Q901 Q902

R742 1.5k

Q705 2SA1049-GR H DF OUT

Q905 Q908 Q909

R784 22k :CHIP

D718 UDZ-5.1B
B-SS3414<U/C>-D.-05

5-15 5-16

(2) Schematic Diagrams of G, GA, H, J and L or L3 Boards

C7504 0.1 :PT

GA BOARD VOLTAGE LIST

INPUT1

D812 SLR-325YCT31

R812 220

INPUT2

Q7504 2SA1037AK SW

R7509 10k :CHIP R7510 10k :CHIP
Pin No. Voltage [V] B C E B C B C B 2.6 2.5 1.7 0.8.6 14.14.0 0.7 0.14.0 13.4

Q801 2SC3311A LED DRIVE

R813 220

L or L3 BOARD

CN801 11P :S-MICRO L

11 TO D BOARD CN501

IC5101, 5301, 5401 LA6510

IC7501

1 GND 2 GND 3 DRIVE 4 I SENSE 5 VCC 6 V SENCE 7 L SENCE 8 AC SENSE 9 OVP 10 LVP TO G BOARD CN610

D813 SLR-325YCT31

R814 10k R815 10k R816 22k R817 22k R824 22k

SG402 C417 10000p 2kV F
A or A3 BOARD * MARK LIST
Ref. No. C109 C113 C213 C309 C313 C413 JR401 JR402 JR403 JR404 Q202 R112 R129 R140 R145 R229 R240 R245 R312 R329 R340 R345 R461 A BOARD 27pF CH:CHIP 100K :CHIP 100K :CHIP 27pF CH:CHIP 100K :CHIP 100K :CHIP # # # # 2SC3545-T1T43T:RN-CP 1M :CHIP 2.2M :CHIP # 1M :CHIP 2.2M :CHIP # 68 :RN-CP 1M :CHIP 2.2M :CHIP # 100K 1/4W A3 BOARD 33pF CH:CHIP # # 22pF CH:CHIP # # 2SC2735JTL 56 :RN-CP 560K :CHIP # 470K :CHIP 560K :CHIP # 470K :CHIP 47 :RN-CP 560K :CHIP # 470K :CHIP 100K 1/2W # : NOT USED

C410 0.01 B:CHIP

Q201 2SA1738 BUFFER

Q206 Q301 Q305

R477 22k :CHIP
R417 C453 47k 0.01 :CHIP B:CHIP
C211 R114 4700p 270 B:CHIP :CHIP R:CHIP R:CHIP

D402 UDZ-TE-17-5.1B

R:CHIP R:CHIP R425 C10p :CHIP CH:CHIP R426 C0.01 :CHIP B:CHIP R:CHIP C435 0.01 B:CHIP R409 1k :CHIP CR406 1k :CHIP R434 4.7k :CHIP R412 1.5k :CHIP C407 C408 0.B:CHIP C405 10p CH:CHIP R423 47k :CHIP R440 47k :CHIP D410 MA111 R413 4.7k :CHIP R:CHIP

C112 0.1 25V B:CHIP

R120 100k :CHIP
CLP LOWB_DET C.BLK GREEN GND INPUT SW GND VIDEO

TO D BARD CN506

D106 1SS376

R111 2.2k :CHIP

C115 0.22 250V L101 0.15H :ALI

R121 100k :CHIP

FB:CHIP C250V
R132 R47 :CHIP :CHIP R117 3.9k :CHIP C111 4700p B:CHIP

Q404 DTC124EKA ASC SW

C491 0.01 B:CHIP

Q101 2SA1738 BUFFER

R329 * :CHIP R367 1M :CHIP

D107 1SS376

+200V R330 100k:CHIP R333 1k R337 :CHIP 100k:CHIP C320 2.2 200V R331 2.2k :CHIP

D105 1SS376

+200V +80V

FB406 1.1UH

C484 1000p R478 500V 1 B :FPRD
R334 100k:CHIP R336 100k:CHIP B_CUTOFF

R416 1k :CHIP

D104 1SS376

C464 10

R407 47k :CHIP R408 100k :CHIP

R411 4.7k :CHIP

D401 MA111 Q405 D403 MA111 2SB709A BUFFER
D103 MA111 D303 D203 MA111 MA111

R325 56k :CHIP 2

Q306 2SA10910 BUFFER

IC406 NJM7812FA 12V REG

O +12V I G

PS401 1A R461 * C465 10

C460 FB405 1000p 1.1UH 500V B

Q401 2SB709A G SYNC

R410 1k :CHIP

12V 4 1

Q403 2SB709A G SYNC

R340 2.2M :CHIP

A ro A3 BOARD WAVEFORMS

ASC_SW OSD_SEL MOSI CLK DAC_SEL HFBP VRET

TO D BARD CN503

Q402 2SC2412 G SYNC
C414 R415 5p 4.7k CH:CHIP :CHIP
Q305 2SC4015 B CUT OFF AMP
R234 100k:CHIP R236 100k:CHIP G_CUTOFF C469 10

C461 0.01 B:CHIP

IC408 TA78L05S 5VREG

O +5V I G

CC463 0.01 B:CHIP

TO G BOARD CN672

Q306 Q401

Q406 Q410

R326 R308 100k 120k :CHIP :CHIP R309 680k :CHIP
R:CHIP C25V R435 1M :CHIP R436 5.6k :CHIP R:CHIP R:CHIP R:CHIP R:CHIP R:CHIP R:CHIP C443 47p :CHIP C445 1000p :CHIP R438 1.5k R439 :CHIP 1.5k :CHIP C409 22p C448 0.1 CH:CHIP 25V C450 B:CHIP 22p CH:CHIP C447 0.125V B:CHIP
IC409(1/4) LM324M-FL63 R230 B CUT OFF 100k:CHIP R233 1k R229 AMP
* :CHIP R267 1M :CHIP :CHIP R237 100k:CHIP C220 2.2 200V R231 2.2k :CHIP
L401 100H STBY+5V C446 IC404 0.1 25V LSC4380DW2AR2 B:CHIP OSD

C317 0.01 B:CHIP

Q206 2SA1091O BUFFER

R470 4.7k :CHIP

C434 0.001 500V :B FB403 1.1UH 1KV

C471 1000p 500V B

Q101 Q105

3.0 Vp-p (H)

37.0 Vp-p (H)
IC410 M62352GP-75ED D/A CONVERTER
Vss AO3 AO4 AO5 AO6 AO7 AO8 AO9 AO10 VDD GND AO2 AO1 MOSI CLK LD MISO AO12 AO11 Vcc

R225 56k :CHIP 6

R226 R208 100k 120k :CHIP :CHIP R209 680k :CHIP C217 0.01 B:CHIP OSD_CONT CONT R126 100k :CHIP R240 2.2M :CHIP
Q205 2SC4015 R CUT OFF CONT

C487 10

C486 0.01 B:CHIP R456 2.2M :CHIP

1KV N.C.

TO D BOARD CN507
C436 47p CH:CHIP C440 47p CH:CHIP C438 47p CH:CHIP C455 47p CH:CHIP C442 47p CH:CHIP C444 47p CH:CHIP
VSSA VCO RP VDDA HFLB SS MOSI CLK NC NC NC NC NC PWM0
VSS R G B FBKG INT VFLB VDD NC NC NC NC NC PWM1
IC409(2/4) LM324M-FL63 R130 G CUT OFF 100k:CHIP R133 1k R129 AMP
* :CHIP R167 1M :CHIP R137 :CHIP 100k:CHIP C120 2.2 200V R131 2.2k :CHIP
R457 22M 1/4W :RN C479 470p :CHIP
R459 R458 10M 2.2M 1W 1W :RN :RN C478 4700p 2kV F

R134 100k:CHIP

R471 6.8k R136 100k:CHIP :CHIP R_CUTOFF

G_CUTOFF B_CUTOFF R_DRV

Q106 2SA1091O BUFFER

35.0 Vp-p (H)

G_DRV C451C0.01 B:CHIP B_DRV BRT

R125 56k :CHIP 9

C457 0.01 B:CHIP R464 2.2k :CHIP
Q410 2SC5022-02 R442 G2 CONT 2.2k

:RN-CP

A or A3 BOARD

D408 MA111

IC402 M52722P
R108 120k :CHIP R109 680k :CHIP R140 2.2M :CHIP
IC409(3/4) LM324M-FL63 R CUT OFF AMP
Q105 2SC4015 R CUT OFF CONT

R462 47k :CHIP

R466 10k :RN-CP R428 1k :CHIP

C466 10

C467 0.01 B:CHIP

C127 0.01 B:CHIP

D405 MA111

C420 47

D406 MA111

C421 10

C424 Q408 0.1 DTA124EKA 25V Q409 B:CHIP SW 2SC2412K SW D409 R451 MA:CHIP R452 4.7k :CHIP R453 10k :CHIP

R454 10k :CHIP

D407 0.01 MA111 B:CHIP

R463 180k :CHIP

IC409(4/4) LM324M-FL63 G2 CONT
R419 33k :RN-CP R420 47k :RN-CP

Q406 DTA124EKA G2 CONT

B-SS3414<U/C>-A.-05

VIDEO AMP RGB OUT

A or A3 BOARD (Conductor Side)
A or A3 BOARD SEMICONDUCTOR LOCATION
A or A3 BOARD (Component Side)
IC401 IC402 IC403 IC404 IC406 IC408 IC409 IC410 B3 B3 A1 A1 A1 B1 B1 A2 A3 A3 C1 A2
Q101 Q105 Q106 Q201 Q202 Q205 Q206 Q301 Q305 Q306 Q401 Q402 Q403 Q404 Q405 Q406 Q408 Q409 Q410 B3 D3 D3 B3 A3 C3 C3 B3 C3 C3 A2 D1 D1

C1 C1 C1 C1 A1 A2 B2 B2

D1 D3 D3 D1

1 1

D101 D102 D103 D104 D105 D106 D107 D201 D202 D203 D204 D205 D206 D207 D301 D302 D303 D304 D305 D306 D307 D401 D402 D403 D404 D405 D406 D407 D408 D409 D410 A1 A1 B3 C1 C3 B3 B3 A1 A1 B3 C1 C3 B3 B3 A2 A1 B3 C1 C2 B2 B3 B2 B3 B2 C3 D3 D3 D1 D1 D1 B2

5-5. SEMICONDUCTORS

BA9756FS-E2 M62352GP-75E M62352GP-75ED

LA6510

NJM4558M TC7W04FU PC4558G2 24LC16BT/SN 24LC21AT/SN

PC78L05J

2SA1175-HFE 2SA1309A-QRSTA 2SC2784 2SC2785-HFE 2SC3311A-QRSTA

LETTER SIDE

TOP VIEW

20 pin SOP

LA7841L

8 pin SOP

CXA2043Q

MARKING SIDE VIEW

48 pin QFP

pin SIP

NJM78L05A NJM78L09A TA78L05S TA78L09S

LM324M TC74HCT04AF

CXA2044M LSC4380DW2AR2

14 pin SOP

NJM78M09FA NJM7812FA TA7805S
DTA114GKAT146 DTA124EKA-T146 DTC114GKA DTC114GKAT146 DTC124EK DTC124EKA-T146 2SA1036K-Q 2SA1036K-T-146-Q 2SA1037AK-T146-QR 2SA1037AK-T146-R 2SA1037K-T-146-QR 2SA1162G 2SA1462-Y33 2SA1738-TX 2SB709A-QRS-TX 2SC1623-L5L6 2SC2411K-CQ 2SC2411K-T-146-CQ 2SC2412K-T-146-QR 2SC3545-T43 2SC2735JTL

2SA1358-Y 2SC3421-Y

2SC2362KG-AA

28 pin SOP

MB90553PF-G-120-BND

2SC3209LK

MX0841AB-F SI-3050F

MC33262P MM1170BFB

FA4111

8 pin DIP

TOP223Y-BB
2SA1049-GR 2SC2458-YGR 2SC2459-GR
2SC3746 2SC5022-02 2SJ449 2SJ449 (1) 2SJ449 (2)

M52722P

LA6500-FA

SOURCE CONTROL DRAIN

52 pin DIP
PC1093J 2SA1091-O 2SC2362K-G

2SC4015TV2

M52755FP

36 pin SOP

2SC5047-CA
D1NL20-TR GMA01 RD12ES-B2 RD16ES-B2 RD16ES-B3 RD18ES-B2 RD22ES-B2 RD5.1ES-B2 RD6.2ESB2 1SS119-25TD 1SS119-25 1SS120TD

CATHODE

FMQ-G5GS D5L60

RM11A RM11C

2SK1120LBSONY2 2SK2098-01MR

MA151WK 1SS184

CATHODE MARK

D2S4MF D2S4MTA1 YG911S3R

2SK2195F04 MA153 1SS226

CATHODE ANODE

AG01A-V0 ERA91-02 S2LA20F
D4SBS4 D4SBS4-F D4SBL40 D4SB60L
1PS226-115 PC123F2 PC123FY2
1SS376TE-17 DTZ-TT11-16B DTZ10B DTZ13B DTZ24B DTZ33B DTZ4.7C DTZ5.1B MA111-TX RD12SB2 RD5.6SB UDZ-TE-17-10B UDZ-TE-17-12B UDZ-TE-17-13B UDZ-TE-17-16B UDZ-TE-17-24B UDZ-TE-17-33B UDZ-TE-17-4.7B UDZ-TE-17-5.1B UDZ-TE-17-5.6B UDZ-TE-17-6.2B D5LC20U P6KE200AG23

CATHODE 12

EGP20G ERA34-10 RGP02-17EL-6433 RGP02-17PKG23 RGP02-20EG23 RGP02-20EL-6394 RGP15GPKG23 UF4005PKG23

RD6.2M-B1

SECTION 6 EXPLODED VIEWS
Items with no part number and no description are not stocked because they are seldom required for routine service. The construction parts of an assembled part are indicated with a collation number in the remark column. Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
The components identified by shading and mark are critical for safety. Replace only with part number specified.

6-1. CHASSIS

4 p 7-685-647-79 7-685-663-71 7-685-872-09 7-685-881-09 +BVTP 3X10 +BVTP 4X16 +BVTT 3X8 +BVTT 4X8
Les composants identifis par un tram et une marque sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

U/C for USA-made set

REF.NO. PART NO.

REMARK REF.NO. PART NO. DESCRIPTION REMARK All variable and adjustable resistors have Items marked " * " are not stocked since characteristic curve B, unless otherwise they are seldom required for routine noted. service. Some delay should be anticipated when ordering these items. RESISTORS All resistors are in ohms F : nonflammable
When indicating parts by reference number, please include the board name. REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK
* 8-933-275-00 A BOARD, COMPLETE * 8-933-364-00 A3 BOARD, COMPLETE ***************************** Note: A complete board and A3 complete board have interchangeability though it is a little different because the material of the circuit board is different. 4-382-854-11 SCREW (M3X10), P, SW (+) (IC403)
C211 C212 C213 C215 C217 C220 C221 C222 C230 C301 C302 C303 C304 C305 C306 C307 C308 C309 C309 C310
1-163-017-00 CERAMIC CHIP 0.0047F 10% 50V 1-164-004-11 CERAMIC CHIP 0.1F 10% 25V 1-216-097-91 RES, CHIP 100K 5% 1/10W (A BOARD) 1-104-514-11 FILM 0.22F 10% 250V 1-163-021-91 CERAMIC CHIP 0.01F 10% 50V 1-107-949-11 ELECT 2.2F 1-163-021-91 CERAMIC CHIP 0.01F 1-164-004-11 CERAMIC CHIP 0.1F 1-163-021-91 CERAMIC CHIP 0.01F 1-163-021-91 CERAMIC CHIP 0.01F 1-104-664-11 ELECT 47F 1-163-021-91 CERAMIC CHIP 0.01F 1-104-664-11 ELECT 47F 1-163-021-91 CERAMIC CHIP 0.01F 1-163-021-91 CERAMIC CHIP 0.01F 1-164-004-11 CERAMIC CHIP 0.1F 1-107-903-11 ELECT 2.2F 1-163-235-11 CERAMIC CHIP 22pF 1-163-237-11 CERAMIC CHIP 27pF 1-163-275-11 CERAMIC CHIP 0.001F 20% 10% 10% 10% 10% 20% 10% 20% 10% 10% 200V 50V 25V 50V 50V 25V 50V 25V 50V 50V
<CAPACITOR> C101 C102 C103 C104 C105 C106 C107 C108 C109 C109 1-163-021-91 1-104-664-11 1-163-021-91 1-104-664-11 1-163-021-91 1-163-021-91 1-164-004-11 1-107-903-11 1-163-237-11 CERAMIC CHIP 0.01F ELECT 47F CERAMIC CHIP 0.01F ELECT 47F CERAMIC CHIP 0.01F CERAMIC CHIP 0.01F CERAMIC CHIP 0.1F ELECT 2.2F CERAMIC CHIP 27pF 10% 20% 10% 20% 10% 50V 25V 50V 25V 50V
1-163-239-11 CERAMIC CHIP 33pF
10% 50V 10% 25V 20% 50V 5% 50V (A BOARD) 5% 50V (A3 BOARD) 5% 50V 10% 50V 10% 25V 5% 1/10W (A BOARD) 10% 250V 20% 10% 10% 10% 10% 10% 20% 10% 20% 10% 10% 10% 20% 5% 5% 200V 50V 25V 50V 50V 50V 25V 50V 25V 50V 50V 25V 50V 50V 50V
10% 25V 20% 50V 5% 50V (A BOARD) 5% 50V (A3 BOARD) 5% 50V
C110 C111 C112 C113 C115 C120 C121 C122 C127 C130 C201 C202 C203 C204 C205 C206 C207 C208 C209 C210
1-163-275-11 1-163-017-00 1-164-004-11 1-216-097-91
CERAMIC CHIP 0.001F CERAMIC CHIP 0.0047F CERAMIC CHIP 0.1F RES, CHIP 100K 0.22F
C311 C312 C313 C315 C317 C319 C320 C321 C322 C330 C401 C402 C403 C404 C405 C407 C408 C409 C410

sci.electronics.repair: Q: Sony GDM500PST monitor problem
Q: Sony GDM500PST monitor problem
Source: http://sci.techarchive.net/Archive/sci.electronics.repair/200502/0757.html
From: Joe (jankro__at_vip.fi) Date: 02/07/05
Date: Mon, 7 Feb 2005 19:13:39 +0200
I'm getting one of these, where the picture rotates horizontally like a figure eight. Is it the CXA2043Q and what else should I check first? Thanks guys, jan finland
jan piste kronlund at tuubi1 piste net Please notice my new address! Osoitteeni on muuttunut, oikea on yll.