3-046-172-11(1)

English

Franais

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.

Operating the Radio

Manual Tuning
1 Press RADIO ON to turn on the radio. 2 Press BAND repeatedly to select the 3
desired band. Use TUNING + or to tune in to the desired station.
The FM channel step is set to 0.1MHz and the AM (MW) channel step is set to 10kHz (North and South American model). The FM channel step is set to 0.05MHz* and the AM (MW) channel step is set to 9kHz (Other models). * The FM frequency display is raised or lowered by a step of 0.1 MHz. For example, frequency 88.00 and 88.05 MHz is displayed as 88.0 MHz. The display shows the band and frequency for a few seconds and then changes back to the current time.

Setting the Alarm

Before setting the time for the radio and buzzer alarms, make sure you have set the current time (See Setting the Clock and date).

ALARM OFF

The alarm is turned off automatically after 60 minutes.

Precautions

Operate the unit on the power sources specified in Specifications. The nameplate indicating voltage, etc. is located at the bottom of the unit. To disconnect the power cord (mains lead), pull it out the plug, not by the cord. Do not leave the unit in a location near a heat source such as a radiator or airduct, or in a place subject to direct sunlight, excessive dust, mechanical vibration, or shock. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that block the ventilation holes. Should any liquid or solid object fall into the unit, unplug the unit and have it checked by qualified personnel before operating it further. When the casing becomes soiled, clean it with a soft cloth dampened with a mild detergent solution. Never use abrasive cleaners or chemical solvents, as they may mar the casing. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Do not connect the antenna lead to an external antenna. If you have any questions, please consult your nearest Sony dealer.

AVERTISSEMENT

Pour viter tout risque dincendie ou dlectrocution, nexposez pas lappareil la pluie ni lhumidit. Afin dcarter tout risque dlectrocution, nouvrez pas le coffret. Confiez les rparations exclusivement un technicien qualifi.
Fonctionnement de la radio

Accord manuel

1 Appuyez sur RADIO ON pour allumer

la radio.

Lafficheur indique la gamme et la frquence pendant quelques secondes puis lheure actuelle apparat.

Rglage de lalarme

Avant de rgler lheure pour les alarmes radio et sonnerie, assurez-vous de bien avoir rgl lheure actuelle (Voir Rglage de lheure et de la date.).

ALARME DSACTIVE

Lalarme se dsactive automatiquement au bout de 60 minutes.
FM/AM PLL Synthesized Clock Radio ICF-C253 FM/MW/LW PLL Synthesized Clock Radio ICF-C253L
Operating Instructions Mode demploi Bedienungsanleitung (Rckseite) Gebruiksaanwijzing (achterzijde)

To Stop the Alarm

Press ALARM RESET to turn off the alarm.
The alarm will come on again at the same time the next day.

Pour arrter lalarme

Appuyez sur ALARM RESET pour teindre lalarme.
Lalarme se dclenchera de nouveau le jour suivant la mme heure.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

To Set the Alarm Time

1 Set the alarm setting dial to either
ALARM TIME SET A (radio) or ALARM TIME SET B (buzzer). After one beep, the indicator A or B and the alarm time set in the previous time will flash in the display.
For the Customers in Canada CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Pour rgler lheure de lalarme
1 Meltez la molette de rglage de lalarme
sur ALARM TIME SET A (radio) ou ALARM TIME SET B (sonnerie). Aprs un bip, lindicateur A ou B et lheure de lalarme rgle antrieurement clignotent sur lafficheur. Appuyez sur CLOCK + ou jusqu ce que lheure souhaite apparaisse. Si vous maintenez CLOCK + ou enfonce, lheure affiche changera dabord par incrments dune minute puis, quelques secondes plus tard, par incrments de dix minutes. sur ALARM MODE OFF. Deux brefs bips confirment le rglage.
Lorsque la molette de rglage de lalarme est mise sur ALARM TIME SET A ou B, la radio sarrte.
Si le coffret est sale, nettoyez-le avec un chiffon doux humect dune solution dtergente douce. Nutilisez jamais de produits de nettoyage abrasifs ni de solvants chimiques, car ils pourraient endommager la finition du coffret. Lappareil nest pas isol du secteur tant quil est branch sur une prise secteur, mme sil est teint. Ne pas connecter le fil de lantenne a lantenne externe. Pour toute question, consultez votre revendeur Sony.

Rglage du temporisateur

Vous pouvez vous endormir au son de la radio grce au temporisateur incorpor qui met automatiquement la radio hors tension lissue dune dure spcifie.

Press SLEEP.

The radio turns on. You can set the sleep timer to durations of 90, 60, 30, or 15 minutes. Every push changes the display as follows.

Features

Dual alarm FM/AM (ICF-C253) or FM/MW/ LW (ICF-C253L) PLL (phase locked loop) synthesized clock radio. LCD with backlight, and brightness adjustment for the backlight. Date button to display the year, month and day. Easy radio presetwith the pressing of a button. D.S.T. (Daylight Saving Time)Summer time adjustment (one-hour skip function). 5 random station presets. Radio and buzzer alarms. Extendable snoozesnooze time can be extended from 8 to 60 minutes in maximum every time you use.
To turn off the radio, press RADIO OFF. To listen with an earphone, connect the earphone to the v (earphone) jack. The speaker is deactivated when an earphone is connected (ICF-C253 for European model only) To improve reception FM: Extend the FM wire antenna fully to increase reception sensitivity. AM(MW)/LW: Rotate the unit horizontally for optimum reception. A ferrite bar is built in to the unit. Do not operate the unit over a steel desk or metal surface, as this may lead to interference of reception. To check the station being received, press TUNING + or lightly. The display shows the band and frequency for a few seconds and then changes back to the current time. If the radio alarm comes on while the radio is on, the unit switches to the station on preset button 1 (WAKE UP STATION).

To Activate the Alarm

Set the alarm setting dial to the desired alarm mode (radio, buzzer, or radio and buzzer), and the indicator(s) you chose will be lit. Alarm Radio Buzzer Radio and Buzzer Set the alarm setting dial to A RADIO B BUZZER A+B Lighting indicator A B A and B
Deux brefs bips retentissent lorsque la frquence infrieure de chaque gamme est accorde. Rglez le volume avec VOL.

Appuyez sur SLEEP.

La radio sallume. Vous pouvez rgler le temporisateur sur 90, 60, 30 ou 15 minutes. A chaque pression, lafficheur change de la faon suivante.
3 Mettez la molette de rglage de lalarme
Modle pour les autres pays Gamme ICF-C253 FM GO ICF-C253L Intervalle daccord

On (En service) 60

87,5-108 MHz 87,5-108 MHz 0,05 MHz 153-279 kHz 9 kHz
AM(PO) 531-1.602 kHz 531-1.602 kHz 9 kHz Haut-parleur Env. 6,6 cm (2 5/8 po.) de dia. Sortie Prise v (couteur) (minijack 3,5 mm) (modle ICF-C253 pour lEurope seulement) Puissance de sortie 200 mW ( une distorsion harmonique de 10%) Alimentation Modle pour lAmrique du Nord et du Sud: 120 V CA, 60 Hz Modle pour lAustralie: 240V CA, 50 Hz Autres modles : 220-230 V CA, 50 Hz Dimensions Env. 180,140 mm (7 1/1/5/8) (l/h/p), saillies et commandes comprises Poids Env. 640 g (1 li. 7 on.) ICF-C253L (Royaume-Uni): Env.660 g (1 li. 8 on.) La conception et les spcifications sont sujettes modification sans pravis.

Pour activer lalarme

Meltez la molette de rglage de lalarme sur le mode dalarme souhait (radio, sonnerie ou radio et sonnerie). Le ou les indicateurs choisi(s) sallume(nt). Meltez la molette de rglage de lalarme sur A RADIO B BUZZER A+B Indicateur clair A B A and B
Deux brefs bips retentissent lorsque laffichage revient On. SLEEP apparat sur lafficheur lorsque le temps est rgl. La radio fonctionne pendant la dure prrgle, puis steint. Pour teindre la radio avant lheure prrgle, appuyez sur SNOOZE/DATE/SLEEP OFF.
Alarme Radio Sonnerie Radio et Sonnerie
Model for other countries Band FM LW ICF-C253 87.5-108 MHz ICF-C253L 87.5-108 MHz 531-1,602 kHz 153 - 279 kHz Channel step 0.05 MHz 9 kHz 9 kHz

Sony Corporation 2000

Printed in Malaysia

Preset Tuning

You can preset up to five stations for one-touch tuning; one for each of the preset buttons 1 to 5.
1 Set the alarm. (See Setting the

Alarm.)

AM(MW) 531-1,602 kHz
Pour utiliser simultanment le temporisateur et lalarme
Vous pouvez vous endormir au son de la radio, et tre rveill par la radio ou la sonnerie lheure prrgle.
Setting the Clock and date
1 Set the alarm setting dial to ALARM

MODE OFF.

2 Plug in the clock radio. 3 Press CLOCK for a few seconds.
The display will flash AM 12:00 or 0:00. You will hear a beep and the year will start to flash in the display.
Presetting a station Example: To preset AM 1260 kHz onto preset button 2. 1 Press RADIO ON to turn on the radio. 2 Tune in to the station you want to preset.

To Check the Alarm Time

Press ALARM TIME CHECK. The display shows the alarm time for a few seconds and then returns to show the current time. When the alarm setting dial is set to either ALARM MODE OFF or ALARM MODE A + B, the alarm time in ALARM MODE A RADIO and then ALARM MODE B BUZZER appears in the display.
Alarm time in ALARM MODE A RADIO and ALARM MODE B BUZZER is set at AM 12:00 or 0:00 when you purchased the unit.
2 Set the sleep timer. (See Setting the

Sleep Timer.)

Troubleshooting
Should any problem occur with the unit, make the following simple checks to determine whether or not servicing is required. If the problem persists, consult your nearest Sony dealer. The clock does not show the correct time. Has an electrical power outage lasting more than 1 minute occurred? The radio or buzzer alarm does not sound at the preset alarm time. Has the desired radio or buzzer alarm been activated? (i.e. Is the indicator A or B lit?) The radio alarm is activated but no sound comes on at the preset alarm time. Has a station been preset onto preset button 1? Has VOL been adjusted ? No sound comes from the speakers. Hasnt the alarm setting dial been remained setting to ALARM TIME SET ?

3 Hold down the desired

STATIONSELECT/PRESET button (in this case, 2) until you hear two short beeps.

(See Manual Tuning.)

4 Press CLOCK + or until the correct 5 6
Earphone jack (ICF-C253 for European model only) Prise dcouteurs (modle ICF-C253 pour lEurope) VOL FM wire antenna Antenne fil FM AC power cord Cordon dalimentation secteur
year appears in the display. Press CLOCK once. Repeat steps 4 and 5 to set the month, day, hour, and minute.
After setting the minute, press CLOCK to start the counting of the seconds, and you will hear two short beeps. The display shows the frequency for a few seconds and then changes back to the current time. For the radio alarm, preset the station to be used as the alarm onto preset button 1.

ALARM ON

When the alarm comes on at the preset time, the alarm indicator flashes. For the buzzer alarm, the beeping of the alarm becomes more rapid after every few seconds in five progressive stages. When both the radio and buzzer alarms are set for the same time, and you choose ALARM MODE A + B, the radio alarm takes precedence.
Speaker Approx. 6.6 cm (2 5/8 in) dia. Output v (earphone) jack ( 3.5 mm minijack) (ICF-C253 for European model only) Power output 200 mW (at 10% harmonic distortion) Power requirements North and South American model: 120 V AC, 60 Hz Australian model: 240 V AC, 50 Hz Other model: 220230 V AC, 50 Hz Dimensions Approx. 180.140 mm (w/h/d) (7 1/1/5/8 in) incl. projecting parts and controls Mass Approx. 640g (1 lb 7 oz) ICF-C253L (UK model) Approx. 660 g (1 lb 8 oz) Design and specifications are subject to change without notice.

3 Tenez la touche STATIONSELECT/
PRESET souhaite enfonce (dans ce cas, 2) jusqu ce que vous entendiez deux brefs bips.

(Voir Accord manuel.)

To display the year and date, press SNOOZE/ DATE/SLEEP OFF once for the date, and within 2 seconds press it again for the year. The display shows the date or year for a few seconds and then changes back to the current time. To set the current time rapidly, hold down CLOCK + or. The clock system varies depending on the model you own. 12-hour system: AM 12:00 = midnight 24-hour system: 0:00 = midnight In step 6, when you press CLOCK after the minute setting to activate the clock, the seconds start counting from zero. When the alarm setting dial is set to ALARM TIME SET A or B, the clock cannot be set.

ALARME ACTIVE

Lorsque lalarme sactive lheure prrgle, lindicateur dalarme clignote. Pour lalarme sonnerie, le bip de lalarme devient plus rapide aprs quelques secondes en cinq tapes progressives. Lorsque les alarmes radio et sonnerie sont rgles la mme heure et que vous choisissez ALARM MODE A+B, la radio a priorit.
To change a preset station
Tune in manually to the station you want to store and hold down the preset button until you hear two short beeps. The previously stored station will be replaced by the new one.
Tuning in to a preset station 1 Press RADIO ON to turn on the radio. 2 Press STATIONSELECT/PRESET where the desired station is stored. 3 Adjust volume using VOL.
After a few seconds, the display will return to the current time but the preset button number will remain.
To Doze for a Few More Minutes
Press SNOOZE/DATE/SLEEP OFF.
The radio or buzzer turns off but will automatically come on again after about 8 minutes. Every time you press SNOOZE/DATE/SLEEP OFF, the snooze time changes as follows:
La frquence est indique pendant quelques secondes, puis lheure rapparat. Pour lalarme radio, prrglez la station qui doit tre utilise comme alarme sur la touche 1.
Pour changer une station prrgle

ICF-C253

SERVICE MANUAL

Ver 1.0 2000. 04

Australian Model

SPECIFICATIONS

FM/AM PLL SYNTHESIZED CLOCK RADIO

SECTION 1 GENERAL

This section is extracted from instruction manual.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.

SECTION 2 DISASSEMBLY

The equipment can be removed using the following procedure.
Set Cabinet (upper) Key board Main board Power board

Note :

Follow the disassembly procedure in the numerical order given.

CABINET (UPPER)

1 Five screws (M3 14)

2 Cabinet (upper)

4 Speaker
3 Remove the two solderings.

KEY BOARD

4 Key board

1 Two claws

2 Two claws

5 Two claws

6 Chassis
3 Remove the eight solderings.

7 Cabinet (lower)

MAIN BOARD
5 Remove the four solderings. 2 Two screws (BTP 2 8) 3 Alarm dial board

6 LED board

1 Remove the five solderings.
7 Remove the four solderings.

8 Main board 4 Claw

SECTION 3 ELECTRICAL ADJUSTMENTS

2-4. POWER BOARD

4 Power cord 6 Transformer power
[FM] Setting: BAND switch: FM
FM RF signal generator 0.01 F level meter +
Adjusting Location: MAIN board (Component Side)
T1 AM IF adjustment CT3 FM TRACKING adjustment L3 L1 AM FREQUENCY COVERAGE adjustment

2 Terminal

22.5 kHz frequency speaker terminal deviation by 400 Hz signal FM lead wire antenna terminal

7 Power board

[AM] Setting: BAND switch: AM
Put the lead-wire antenna close to AM RF SSG the set. set
level meter + speaker terminal
CT1 AM TARCKING adjustment L4
5 Remove the six solderings.
30% amplitude modulation by 400 Hz signal Output level: as low as possible
Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors.
FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L3 87.5 MHz CTHz

2-5. POWER CORD SETTING

AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. LkHz

Power board

AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter.
Set the power cord as illustrated below, then install the lower cabinet.

LkHz AM IF ADJUSTMENT

CT1 1,404 kHz
Adjust for a maximum reading on level meter. TkHz

FM antenna

power cord

lower cabinet

ICF-C253 SECTION 4 DIAGRAMS
4-1. PRINTED WIRING BOARDS
S202 OFF S210 DST S204 ON 1 TUNING CNS200 S201 SP1 (SPEAKER)

FM ANTENNA

C9 S213 CLOCK S212 A-RESET S214 TIME S203 BAND S209 M5 S208 M4 S207 M3 S206 M2 S211 SNOOZE S215 TIME S205 M1 W151 C30 E C19 C10 CF1 T1

11 1-676-850(11)

POWER BOARD
T150 POWER TRANSFORMER P150 AC IN

S1 BRIGHTNESS HI H L

CF2 CCND155 E D154 D152 D151

C24 C158 Q151

AM FERRITE-ROD ANTENNA L4

CT3 L1 L3 K

C157 DW200 8

D153 CND101 C108

TO ALARM DIAL

LED BOARD

A VR1 VOL

Semiconductor

Location
Ref. No. D5 D6 D7 D8 D9 D10 D100 D101 D151 D152 D153 D154 D155 D156 IC1 IC100 Q2 Q3 Q6 Q7 Q8 Q9 Q10 Q100 Q101 Q151 Location E-8 E-7 E-6 E-5 E-3 E-3 D-5 D-5 D-4 D-4 D-4 C-4 C-4

ALARM MODE

D5-D8 BACK LIGHT

1-676-85111

W2 1-1 -852-

11 (11)

LCD100 (LIQUID CRYSTAL DISPLAY)

11 1-676-849(11)

C-8 E-6 C-7 B-8 E-9 D-6 D-6 E-4 E-4 E-5 E-5 C-6
Note on Printed Wiring Boards: X : parts extracted from the component side. b : Pattern from the side which enables seeing.

4-2. SCHEMATIC DIAGRAM

Note on Schematic Diagram: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. C : panel designation. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. U : B+ Line. H : adjustment for repair. Voltages are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ) : AM : Impossible to measure Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Signal path. F : FM f : AM

C116 0.1

Waveform

1 IC100 wf (XOUT)

1V/div 10sec/div

TUNING

SECTION 5 EXPLODED VIEWS
4-3. IC PIN FUNCTION DESCRIPTION
Pin Name INT OUT MUTE BAND1 ALARM A ALARM B KS0 to KS3 XR0 to XR3 P0 P1 to P3 GND E0 VCOL VCOH Vreg0 VDD Xout Xin Vreg1 VLCD0 CAP0, CAP1 VLCD1 COM0 to COM3 LCD0 to LCD12 LCD13, LCD14 CE INT BEEP BAND2 INIT IN I/O O O O O O O I I O I I O I O O O I I O O I LCD drive. Common signal. LCD drive. Segment signal. Not used. Power failure detection. Not used. Buzzer output. Band output. Initialization input. LCD bubbler. Initialization output. Mute output. Band output. ALARM A indicator. ALARM B indicator. Key strove signal. Key return signal. ALARM-TIME input. DIAL signal. Ground. PLL error output. LW/MW VCO input. FM VCO input. Regulator. VDD System clock output. System clock input. Regulator. Description IC100 LCD CONTROL (PD17072GB-019-1A7) Pin No. to to 15 to 27 28, 31 to to 47 48, to 56 NOTE: -XX, -X mean standardized parts, so they may have some differences from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are not supplied. Accessories and packing materials are given in the last of this parts list.

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

not supplied

SP1 P150

Ref. No. * 13

Part No. 3-045-666-11 3-045-669-01 3-045-670-11 3-045-668-11 7-685-647-79 3-045-675-01 X-3378-799-1 3-049-387-01 3-045-677-01 3-045-672-01
Description CABINET (UPPER) KNOB(ALARM) BUTTON (ALARM) BUTTON (MAIN) SCREW+P 3X10 TYPE2 NON-SLIT PANEL, FRONT PANELASSY, FRONT SHEET(WINDOW), ADHESIVE WINDOW (LED) CHASSIS

Remarks

Ref. No. 18 * 19 * SPPT150
Part No. 3-045-667-11 3-368-852-01 7-685-649-79 3-371-765-21 1-553-856-00 1-676-851-11 1-535-771-11 A-3638-829-A 1-676-850-11 1-676-852-11
Description CABINET (LOWER) FOOT SCREW +P 3X14 TYPE2 NON-SLIT SCREW (2X8), +BTP SWITCH, KEYBOARD POWER BOARD TERMINAL DIAL (ALARM) ASSY KEY BOARD LED BOARD
A-3683-190-A MAIN BOARD, COMPLETE 3-933-547-01 SHEET (BAND) 3-919-268-01 KNOB(VOL)
1-504-748-21 SPEAKER (6.6cm) 1-790-431-11 CORD, POWER 1-435-504-11 TRANSFORMER, POWER
SECTION 6 ELECTRICAL PARTS LIST
NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Ref. No. Part No. Description CAPACITORS: uF: F RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable COILS uH: H
SEMICONDUCTORS In each case, u: , for example: uA.: A. , uPA. , PA. , uPB. , PB. , uPC. , PC. , uPD., PD.
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No. C8 C9 C10 C11 C13 C14 C15 C17 C18 C19 C20 C21 C23 C24 C25 C27 C28 C29 C30 C31 C32 C33 C34 C35 C37 C38 C39 C100 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C116 C118
Part No. 1-126-964-11 1-126-963-11 1-126-964-11 1-163-085-00 1-163-021-91 1-163-809-11 1-164-489-11 1-163-021-91 1-163-021-91 1-128-551-11 1-163-021-91 1-163-231-11 1-163-132-00 1-126-960-11 1-126-934-11 1-163-021-91 1-109-982-11 1-109-982-11 1-126-934-11 1-163-021-91 1-163-009-11 1-110-501-11 1-163-125-00 1-163-009-11 1-163-021-91 1-163-259-91 1-163-009-11 1-163-133-00 1-163-133-00 1-163-133-00 1-163-133-00 1-163-009-11 1-163-133-00 1-163-133-00 1-163-133-00 1-126-916-11 1-163-038-91 1-164-346-11 1-163-108-00 1-163-233-11 1-163-021-91 1-163-038-91 1-163-038-91 1-163-038-91 1-163-022-00

Description ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 4.7uF 10uF 2PF 0.01uF 0.047uF 0.22uF 0.01uF 0.01uF 22uF 0.01uF 15PF 430PF 1uF 220uF 0.01uF 1uF 1uF 220uF 0.01uF 0.001uF 0.33uF 220PF 0.001uF 0.01uF 220PF 0.001uF 470PF 470PF 470PF 470PF 0.001uF 470PF 470PF 470PF 1000uF 0.1uF 1uF 43PF 18PF 0.01uF 0.1uF 0.1uF 0.1uF 0.012uF 20% 20% 20% 10% 10% 10% 10% 10% 20% 10% 5% 5% 20% 20% 10% 10% 10% 20% 10% 10% 10% 5% 10% 10% 5% 10% 5% 5% 5% 5% 10% 5% 5% 5% 20%
Remarks 50V 50V 50V 50V 50V 25V 16V 50V 50V 25V 50V 50V 50V 50V 10V 50V 10V 10V 10V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 25V 16V 50V 50V 50V 25V 25V 25V 50V
1-676-850-11 KEY BOARD ********* < CONNECTOR > * CN200 1-580-187-11 SOCKET, CONNECTOR 8P < JUMPER > JC200 1-216-296-91 SHORT < SWITCH > S200 S201 S202 S203 S204 S205 S206 S207 S208 S209 S210 S211 S212 S213 S214 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 1-692-014-11 SWITCH, KEY BOARD (+) SWITCH, KEY BOARD (-) SWITCH, KEY BOARD (OFF) SWITCH, KEY BOARD (BAND) SWITCH, KEY BOARD (ON) SWITCH, KEY BOARD (M1) SWITCH, KEY BOARD (M2) SWITCH, KEY BOARD (M3) SWITCH, KEY BOARD (M4) SWITCH, KEY BOARD (M5) SWITCH, KEY BOARD (D.S.T) SWITCH, KEY BOARD (SNOOZE) SWITCH, KEY BOARD (A-RESET) SWITCH, KEY BOARD (CLOCK) SWITCH, KEY BOARD (TIME +) 0
S215 1-692-014-11 SWITCH, KEY BOARD (TIME -) ************************************************************ 1-676-852-11 LED BOARD ********* < DIODE > D9 8-719-079-31 LED SLI-342YCT32-RS (B) D10 8-719-079-31 LED SLI-342YCT32-RS (A) ************************************************************ * A-3683-190-A MAIN BOARD, COMPLETE ********************* < FILTER > BPF1 1-236-022-11 FILTER, BAND PASS < CAPACITOR > C3 C4 C5 C6 C7 1-163-251-11 1-163-141-00 1-163-021-91 1-163-227-11 1-163-141-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 0.001uF 0.01uF 10PF 0.001uF 5% 5% 10% 0.50PF 5% 50V 50V 50V 50V 50V