Diameter 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm 1.2mm 1.6mm
Remarks 0.25Kg 0.50Kg 0.50Kg 0.25Kg 1.00Kg 1.00Kg 1.00Kg 1.00Kg
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com
ITEM MODEL Television System Stereo System Channel Coverage VHF : E02-E12 UHF : E21-E69 CATV : S01-S20 HYPER : S21-S41 D/K : R1-R12, R21-R69 L : F2-F10, B-Q, F21-F69 I : UHF B21-B69 UHF : B21-B69 Color System PAL, SECAM NTSC 3.58/4.43 (VIDEO ONLY) MPEG-2 MP@ML PAL, SECAM NTSC 3.58/4.43 (VIDEO ONLY) MPEG-2 MP@ML

B/G/H, D/K, I, L,DVB-T

GERMAN/NICAM Stereo

I, DVB-T

NICAM Stereo

Projected Picture Size

LCD (Liquid Crystal Display) Panel KDL-26P2520/P2530 (26inches) KDL-32P2520/P2530 (32inches) KDL-40P2530 (40inches).
Sound Output Right and Left speaker Sub-woofer General Specifications Power Requirements 220 - 240V KDL-26P2520/P2530: Approx. 100W or less/1W or less KDL-32P2520/P2530: Approx. 115W or less/1W or less KDL-40P2530: Approx. 190W or less/0.8W or less 2 x 10W (RMS)
Input/Output Terminals [REAR]
AV1: 21-pin Euro connector (CENELEC standard)
Inputs for Audio and Video signals. Inputs for RGB. Outputs of TV Video and Audio signals.
Power Consumption/ Standby
KDL-26P2520/P2530: Approx. 663x503x220mm (With stand) Approx. 663x472x128mm (Without stand) KDL-32P2520/P2530: Approx. 797x580x220mm (With stand) Approx. 797x548x125mm (Without stand) KDL-40P2530: Approx. 988x687x270mm (With stand) Approx. 988x653x128mm (Without stand)
Dimensions AV2: 21-pin Euro connector (CENELEC standard) Inputs for Audio and Video signals. Inputs for RGB. Outputs of Video and Audio signals (Selectable). SmartLink interface.
KDL-26P2520/P2530: Approx. 12kg (With stand) Approx. 10kg (Without stand) KDL-32P2520/P2530: Approx. 15kg (With stand) Approx. 13kg (Without stand) KDL-40P2530: Approx. 24kg (With stand) Approx. 21kg (Without stand)

Weight

AV3: Phono Jacks
Y: 1 Vp-p, 75 ohms, 0.3V negative sync PB/CB: 0.7 Vp-p, 75 ohms PR/CR: 0.7 Vp-p, 75 ohms Audio Input Jacks: 500mV rms, 47Kohms. Supplied Accessories
RM-ED007 Remote Commander (1) IEC designated R06 battery (2) Cable Holder (1) (KDL-40P2530 only) Support Belt (1) and Screws (2)

Set the time and date of a programme you want to record Manual timer REC
Digital EPG (in digital mode only) External Inputs
Launches the Digital Electronic Programme Guide (EPG). For details about settings, see page 14. Selects equipment connected to your TV.
Press. Press F/f to select Manual timer REC, then press. Press F/f to select the date, then press g. Set the start and stop time in the same way as in step 3. to set the Press F/f to select the programme, then press TV and your VCR timers.
To watch the desired external input, select the input source, then press. To assign a label to an external input, see page 20. Settings
Opens the Settings menu screen where most of advanced settings and adjustments are performed. Select a menu icon, select an option and make the desired change or adjustment using F/f/G/g. For details about settings, see page 17 to 22.

Picture Adjustment menu

Sound Adjustment Sound Effect Treble Bass Balance Standard 0 Reset Dual Sound Auto Volume TV Speakers Mono On On

Sound Adjustment menu

You can select the options listed below on the Sound menu. To select options in Settings, see Navigating through menus (page 16).

Picture Adjustment

Picture Mode Backlight Contrast Brightness Colour Hue Sharpness Colour Tone Reset Noise Reduction

Back: Enter:

Custom 5 Max Warm
You can select the options listed below on the Picture menu. To select options in Settings, see Navigating through menus (page 16).

Select: Exit:

Enter:

Picture Mode

Selects the picture mode. Vivid: For enhanced picture contrast and sharpness. Standard: For standard picture. Recommended for home entertainment. Custom: Allows you to store your preferred settings.

Sound Effect

Selects the sound mode. Standard: Enhances clarity, detail, and sound presence by using BBE High definition
Adjusts the brightness of the backlight.
Increases or decreases picture contrast.
Sound System. Dynamic: Intensifies clarity and sound presence for better intelligibility and musical realism by using the BBE High definition Sound System.BBE ViVA: BBE ViVA Sound provides musically accurate natural 3D image with Hi-Fi sound. The clarity of the sound is improved by BBE while the width depth and height of sound image are expanded by BBEs proprietary 3D sound process. BBE ViVA Sound is compatible with all TV programs including news, music, dramas, movies, sports and electronic games.
Brightens or darkens the picture.
Adjusts higher-pitched sounds. Adjusts lower-pitched sounds. Emphasizes left or right speaker balance. Resets all the sound settings to the factory settings. Selects the sound from the speaker for a stereo or bilingual broadcast. Stereo, Mono: For a stereo broadcast. A/B/Mono: For a bilingual broadcast, select A for sound channel 1, B for sound channel 2, or Mono for a mono channel, if available.

Horizontal (Pixel) Vertical (Line)
Horizontal frequency (kHz)
Picture noise when viewing a TV channel
SVGA 60 VESA VESA VESA Guidelines
No colour or irregular colour when viewing a signal from the 3 Y, PB/CB, PR/CR jacks of Irregular picture when viewing a signal from PC
This TVs PC input does not support Sync on Green or Composite Sync. This TVs PC input does not support interlaced signals. This TVs PC input supports signals in the above chart with a 60 Hz vertical frequency. For other signals, you will see the message NO SYNC.

Troubleshooting

No sound, but good picture
Check whether the 1 (standby) indicator is flashing in red.
When it is flashing The self-diagnosis function is activated. 1 Measure how long the 1 (standby) indicator flashes and stops flashing.

Noisy sound

Cause/Remedy Press 2 +/ or % (Mute). Check that TV Speakers is set to On in the Sound Adjustment menu (page 18). See the Picture noise causes/remedies on page 27.
For example, the indicator flashes for two seconds, stops flashing for one second, and flashes for two seconds.

Channels

Press 1 on the TV (top side) to switch it off, disconnect the mains lead, and inform your dealer or Sony service centre of how the indicator flashes (duration and interval). When it is not flashing 1 Check the items in the tables below. 2 If the problem still persists, have your TV serviced by qualified service personnel.
Cause/Remedy Switch between digital and analogue mode and select the desired digital/ analogue channel.

Picture

The desired channel cannot be selected Some channels are blank

Cause/Remedy

No picture (screen is dark) and no sound
Check the aerial connection. Connect the TV to the mains, and press 1 on the TV (top side). If the 1 (standby) indicator lights up in red, press "/1.
Scrambled/Subscription only channel. Subscribe to the Pay Per View service. Channel is used only for data (no picture or sound). Contact the broadcaster for transmission details.
Digital channel is not displayed
No picture or no menu information from equipment connected to the scarts or HDMI IN socket
Check that the aerial is plugged directly into the TV (not through other equipment). Contact a local installer to find out if digital transmissions are provided in your area. Upgrade to a higher gain aerial.
Check that the optional equipment is on and press / repeatedly until the correct input symbol is displayed on the screen. Check the connection between the optional equipment and the TV. When connecting any equipment to the HDMI IN 6, 7 socket or when changing the resolution, some dots can appear blinking on the screen for a few seconds. HDMI signal decoding is in progress and it does not indicate a malfunction.

General

The TV turns off automatically (the TV enters standby mode)
Double images or ghosting
Check aerial/cable connections. Check the aerial location and direction.
Cause/Remedy Check if the Sleep Timer is activated, or confirm the setting of Off Time (page 20). If no signal is received and no operation is performed in the TV mode for 10 minutes, the TV automatically switches to standby mode.
The TV turns on automatically Some input sources cannot be selected The remote does not function
Only snow and noise appear on the screen
Check if the aerial is broken or bent. Check if the aerial has reached the end of its serviceable life (three to five years in normal use, one to two years at the seaside).
Distorted picture (dotted lines or stripes)
Check if the On Time is activated (page 20). Select AV Preset in the Set-up menu and cancel Skip of the input source (page 20).
Keep the TV away from electrical noise sources such as cars, motorcycles, hair-dryers or optical equipment. When installing optional equipment, leave some space between the optional equipment and the TV. Make sure that the aerial is connected using the supplied coaxial cable. Keep the aerial cable away from other connecting cables.

Replace the batteries.

SECTION 2 DISASSEMBLY

2-1. STAND REMOVAL

2-2. REAR COVER REMOVAL

Ten screws

One screw

Rear Cover

2-3. SPEAKER REMOVAL

Two screws 1

Two screws 2
2-4. A1/A1P BOARD REMOVAL

Two screws A1/A1P Board

2-5. BDTR-2 BOARD REMOVAL

Two screws BDTR-2 Board

2-6. G1 or G2 BOARD REMOVAL

Three screws

G1 Board (KDL-26/32P2520/30) or G2 Board (KDL-40P2530)
2-7. H1/H1P BOARD REMOVAL

H1/H1P Board

Two screws
2-8. H2/H2P BOARD REMOVAL
Two screws Two screws H2/H2P Board
2-9. H3/H3P BOARD REMOVAL

H3/H3P Board

2-10. LCD PANEL REMOVAL

Six screws

LCD Panel
SECTION 3 CIRCUIT ADJUSTMENTS
3-1. Electrical Adjustments
Service adjustments to this model can be performed using the supplied remote Commander RM-ED007. How to enter into the Service Mode 1. 2. Turn on the main power switch. Press the following sequence of buttons on the Remote Commander.

E C S D D C C L K

O H D C M S S
(9) (10) (11) (12) (13) (14) (15)

(17) (18)

(19) (20)
Key: 1. Model configuration. a. To set 26 AUO (TT68). b. To set 26 Samsung (TT72). c. To set 32 AUO (TT69). d. To set 32 Samsung (TT73). e. To set 20 Chi-Mei (TT71). f. To set 40 Samsung (TT74). 2. Model destination. 3. Command prompt. 4. ECS enabled/disabled (TT31). 5. CBA is shown when the TV set is in CBA mode (This mode is available from Factory mode) (TT27). 6. Normal or Factory mode (TT19). 7. DDC enabled/disabled (TT65). 8. E is shown when EDID WP is enabled; - is shown otherwise (TT66). 9. O is shown when OTRUM is enabled; - is shown otherwise (TT38). 10. H is shown when Hotel mode is enabled; - is shown otherwise (TT37). 11. D is shown when Digital mode is enabled; A is shown when Analogue mode is enabled. 12. C (Default value) is shown when MSP Auto Carrier Mute function is enabled; - is shown otherwise (TT67). 13. M (Default value) is shown when AM sound is demodulated in MSP; A is shown when AFRIC demodulator is used (TT63). 14. S is shown when a SONY tuner is selected; P is shown when a PHILIPS tuner is selected (TT55). 15. C is shown when a Chi-Mei 20 panel is used; S is shown when a Samsung panel is used; A is shown when a AUO panel is used (Changed by TT68 and TT69) for 26 and 32 respectively; 3 is shown when a 40 Samsung A3 panel is used; 4 is shown when a 40 Samsung A4 panel is used (Changed by TT64). 16. Clk is shown when display clock is enabled; - is shown otherwise (TT36). 17. T is shown when digital test is enabled; - is shown otherwise (TT39). 18. W is shown when Watchdog is enabled; - is shown otherwise (TT54). 19. C is shown when chip select is enabled; - is shown instead (This mode is available from factory mode) (TT58). 20. V is shown when Visual I2C is enabled; - is shown otherwise (TT59).

- 24 -

4-1. BLOCK DIAGRAMS (1)
TU1300 TUNER TU AGC SCL SDA 33V 5V ANALOG IF IF AGC DIGITAL IF 2 DIGITAL IF 1 CN31 TO BDTR-2 BOARD CN15
TUNER BLOCK ANALOG AGC SW 12C SCL SW 12C SDA SW 33V +5VA IF ANALOG IF AGC DIGITAL IF DIGITAL + IF DIGITAL ANALOG AGC SW 12C SCL SW IC1000 ANALOG MULTIPLEXER/ DEMULTIPLEXER
4 Z 15 Y 14 X 9 C 10 B 11 A 12 XYXY1
33V 5V D1200 RECTIFIER 5V STBY 5V ANALOG AGC
SW1201 FILTER SURFACE WAVE

YYY4 14

BUF-MDO-CLK BUF-MDO-STRT BUF-MDO-EN IC5754 INVERTING BUFFER
MODE 2 LINE R NVM-WP LINE L MONITOR R MONITOR L SELECT OUT R SELECT OUT L
MD1 7/A25 MD1 6/A24 MD1 5/A23 MD1 4/A22 MD1 3/A21 MD1 2/A20 MD1 1/A19 MD1 0/A18 MOSTRT MOVAL MOCLK MICLK MIVAL MISTRT IOWR

AAAA7 9

IN-TSBCLK IN-TSBSYNC IN-TSPVAL
BUF-MDO-EN IN TSD(0) IN TSD(1) IN TSD(2) IN TSD(3) IN TSD(4) IN TSD(5) IN TSD(6) IN TSD(7) IN-TSBCLK IN-TSBSYNC IN-TSPVAL TXDIB RXDIB
XX5680 XIC5781 DROPOUT REGULATOR CONTROL 1
AUX-MUX OUT R AUX-MUX OUT L

IC5782 STEREO DAC

W6 Y5 AA4 W5 C21 A20 B20 W3 Y3 AA2 V16 V9
PDHDMI/MAIN ON TUNER 12C SWITCH 8.5V TCK TDO
ADO ALRCK ABCK AMCK nSMC INT CI PWR EN nCI EN PMSDIO PMSBS PMSSCLK PMSINS RESET N Q5923 SWITCH

1 DATA 4

5V AUDIO

NOISE OUT

RO 5 LO 8

2 A-IN 6 B-IN

A-OUT 1 B-OUT 7
DIGITAL RF R DIGITAL RF L
TDI TMS POWER LCD POWER DET EDID WP

AUDIO DAC & AMP

IC5783 OP AMP

IC3001 COMPARATOR

IC5786 USB POWER SWITCH nC1 EN
AUDIOWS-HDMI CI PWR EN AUDIODATA-HDMI AUDIOCLK-HDMI PC-HDMI

CN3008

JTAG RESET RXD1B TXD1B JTAG RESET JIG MODE SDA 5V SCL 5V RXD RXD TXD TXD SDA SCL JIG MODE SDA COFDM SCL COFDM VDO(0) VDO(1) VDO(2) VDO(3) VDO(4) VDO(5) VDO(6) VDO(7) VDO CLK

Q3000 HIGH SPEED SWITCH

AV LINK
SHEET 2 G CN3002 KEY KEY SHEET 2 H STBY LED ON-TIMER GREEN LED REC LED SIRCS SHEET 2 J
Q5922 BUFFER IC5780 REAL TIME CLOCK
INT-HDMI RF-DIGITAL KEY POWER ON/ POWER ON LED X5780 OSC OUT 8 PC BLUE PC GREEN PC RED VIDEO AMP BUFFER Q5780 BUFFER AMP

Q3004 HIGH SPEED SWITCH

PORT CS

TO H1/H1P BOARD CN9000

CN3003

SERVICE CONNECTOR

SDA EMMA
Q5920 BUFFER Q5921 BUFFER

SDA SDA

INTRC 4 OSC IN 9

TO H3/H3P BOARD CN9300

SCL EMMA

Q3122 BUFFER

Q3120 SWITCH

CVBS nFE-RESET

SHEET 2 K SHEET 2 L SHEET 2 M SHEET 2 N PMSBS PMSDIO PMSINS PMSSCLK SHEET 2 P SHEET 2 R

CN5883

MEMORY STICK

JTAG RESET

SHEET 2 S SHEET 2 T

- 26 -

4-1. BLOCK DIAGRAMS (3)
IC4202 HDMI RECEIVER SHEET 1 F DB(0) DB(1) DB(2) DB(3) DB(4) DB(5) DB(6) MAIN MICRO CONTROLLER, PANEL DRIVING, AUDIO & VIDEO PROCESSOR DB(7)

C1202 0.01 25V

Q1200 MSD601-RST1 R1202 1k 1/10W AGC_DEFE A T R1200 XX

ANALOG_TUNER

~ A1/A1P Board Schematic Diagram [ Tuner, I/O Connectors & A/V Switching ] Page 2/3 ~

- 31 -

CVBS_ANALOG_RF

SCL_5V

SDA_5V

C1201 XX

Q1201 MUN2213T1

SW1200 SAW FILTER

IC1200 TDA9886TS/V4,118 IF-PLL DEMODULATOR

SCL TU AGC

R1/10W R1/10W
C1206 0.01 25V C1209 0.47 10V

R1217 R0

R1223 1.8k 1/10W

C1204 0.01 25V

R1214 3.3k 1/10W C1205 390p 50V

C1212 XX

C1215 XX

R1212 5.6k 1/10W

CN2022 49P WHT

R2148 XX R2147 0

BUFFER_V R8.5V +5VA +33V CN2024 20P WHT AGC_DEFEAT

SV_STBY/AUDIO MONO

5V_STBY
+8.5V +5V GND +33V GND PORT_CS TUNER_I2C_SW GND I2C_SCL_OFDM I2C_SDA_OFDM
AGC_DEFEAT AM R2144 XX AU_MUX_OUT_R AU_MUX_OUT_L AU_MUX_CTRL_B AU_MUX_CTRL_A
RRC2041 XX RRPORT_CS TUNER_I2C_SWITCH I2C_SCL_OFDM I2C_SDA_OFDM IF_AGC_DIGITAL SCL_5V SDA_5V IF_DIGITAL_IF_DIGITAL_+ RC2037 XX RU_YUV RRY_YUV CVBS_ANALOG_RF ANALOG_TUNER

TO BDTR-2 BOARD CN3006

GND AU_MUX_OUT_R AU_MUX_OUT_L AU_MUX_CTRL_B AU_MUX_CTRL_A QSS GND LINEOUT_R LINEOUT_L GND L2 OUT R2 OUT GND L1 IN R1 IN GND L1 OUT R1 OUT V_YUV
GND AGC_DIGITAL GND I2C_SCL I2C_SDA GND IF_DIGITAL_IF_DIGITAL_+ GND CVBS_TUNER GND V_YUV GND

TO BDTR-2 BOARD CN3005

OUT_R OUT_L AUDIO SCART2 SC2-OUT-L SC2-OUT- R SC1-IN-L SC1-IN-R AUDIO SCART1

C2042 XX RR2038 0

C2040 XX

SC1-OUT-L SC1-OUT-R

U_YUV GND Y_YUV GND CVBS2_OUT GND
TP2 C2038 XX TP3 C2039 XX

C2036 XX C2030 XX

R2044 0
V-OUT-2B RR-IN-2 V MODE2 RAV_LINK BLK2 RBLUE-2

I2C TUNER SWITCH

R1005 XX IC1000 MC74LVX8053DTR2 ANALOG MULTIPLEXER/ DEMULTIPLEXER Y1 Y0 Z1 Z Z0 ENABLE NC GND VCC Y X X1 X0 A B C RCHIP
CVBS2_IN MODE2 AV_LINK FBLK2 B2 GND G2 GND R2 GND CVBS1_OUT GND CVBS1_IN MODE1 FBLK1 B1 GND G1 GND R1

C2082 XX R2046 0

+5VA L1000 10uH C35V I2C_SCL_SW I2C_SDA_SW RRR1007 0

R1011 1k 1/10W SDA_5V

R2047 R0 C2034 RXX
GREEN-2 SCL_5V RED-2 V-OUT-1B VIDEO SCART1
R1/10W I2C_SCL_OFDM ANALOG_AGC R1000 XX

R2146 XX

C1001 0.1 25V
D1102 UDZSTE-175.6B R1/10W

R1003 0

R2061 0

V-IN-1 MODE1

C2083 XX R2049 0
BLK1 BLUE-1 GREEN-1 RED-1

R0 CHIP

RRRCHIP RCHIP
I2C_SDA_OFDM TUNER_I2C_SWITCH R1010 0

ANALOG_AGC_SW

A / B BOARD CONNECTORS
A1/A1P (3/3) Board Waveforms

R5742 XX

RDATA[1]
nMASTER_RESET NAND_WPB R5741 XX

R5743 XX

NAND_ALE,NAND_CLE,NAND_RBB

R5729 68

VDDQ VSSQ LDQS UDQS NC VDD NC LDM WE CAS RAS CS NC BS0 BS1 A10 A0 A1 A2 A3 VDD NC VREF VSS UDM CLK CLK CKE NC A12 A11 A9 A8 A7 A6 A5 A4 VSS

R5734 68

RDATA[0-15]

RB5682 100

DVREF RRRRRB5685 100

DWEB DCASB DRASB DCSB

DQM1 DCLKB DCLK_DDR DCKE DADD[12] DADD[11] DADD[9] DADD[8] DADD[7] DADD[6] DADD[5] DADD[4]
DBA0 DBA1 DADD[10] DADD[0] DADD[1] DADD[2] DADD[3]

STRAP PINS

RDATA[0] = 1 = ENDIAN = Big Endian RDATA[2:1] = 10 = MRGMODE1-0 = Full merge & All bytes RDATA[3] = -- = RESERVED RDATA[5:4] = 11 = VRCLKSEL1-0 = 201MHz RDATA[8:6] = 101 = MCLKSEL2-0 = 187MHz RDATA[9] = 1 = ROMBEND = Big Endian RDATA[10] = 1 = BWSEL = 8bit RDATA[11] = 1 = MINIBOOT = use miniboot RDATA[13:12] = 11 = BOOTSEL1-0 = Nand, then Memory Stick RDATA[15:14] = 00 = BOOT_NAND_SEL1-0 = <256mbit RADD[25] = 1 = EJTAG_MODE = EJTAG RADD[24] = 0 = DINT_EN = disable RADD[23] = 1 = DSYSELB = main only RADD[22] = 1 = PCIMODE = host RADD[21:20] = 00 = PCI_SIZE1-0 = 32Mbyte RADD[19] = 0 = NANDCS = CS0

RB5683 100

RB5684 100

RB5686 100

DADD[0-12] DBA0,DBA1,DCASB,DCKE,DCLKB,DCLK_DDR,DCSB,DQM0,DQM1,DQS0,DQS1,DRASB,DVREF,DWEB

R5680 XX

R5682 XX

R5684 1k

R5689 1k
PLACE THESE CLOSE TO PIN 49 OF IC

R5721 XX

R5719 XX

R5711 XX

R5725 XX

R5715 1k

R5717 1k

R5699 1k

R5703 1k

R5707 1k

R5695 1k

R5723 1k

R5727 1k

RDATA[15]

R5730 100
BOOT_NAND_SEL_1 BOOT_NAND_SEL_0 BOOTSEL1 BOOTSEL0 MINIBOOT BWSEL ROMBEND MCLKSEL2 MCLKSEL1 MCLKSEL0 VRCLKSEL1 VRCLKSEL0 RESERVED MRGMODE1 MRGMODE0 ENDIAN
RDATA[14] RDATA[13] RDATA[12] RDATA[11] RDATA[10] RDATA[9] RDATA[8] RDATA[7] RDATA[6] RDATA[5] RDATA[4] RDATA[3]

R5731 100

C5690 0.1 10V

C5692 4.7 10V

PLEASE PLACE COMPONENTS IN THIS BOX IN SAME AREA ON PWB
RDATA[2] RDATA[1] RDATA[0]

27MHZ CLOCK

3.3V_MAIN FB5681 0uH
R5690 XX R5696 XX R5700 XX R5704 XX R5708 XX R5683 1k R5716 XX R5718 XX R5681 1k R5724 XX R5728 XX R5712 1k R5685 XX R5720 1k R5722 1k R5726 1k
LAYOUT NOTE:REMOVE GND PLANE AROUND IC3201 AND X3200 AND ALSO FROM UNDERNEATH X3200 AND IC3201 INCLUDING TRACKS FROM XTAL TO IC.

C5685 0.1 10V

C5686 1000p 50V

R6563 22k 1/10W D4207 MMDL914T1 R6565 10k 1/10W R6566 150k 1/10W

VH_DDH_3.3

CEC_IN
D4200 XX Q4219 2SK2036(TE85L)

R6571 10k 1/10W

L4208 2.2uH

R4211 4.7k 1/10W

Q4215 2SK2036(TE85L) R6564 XX

HOT_PLUG1

CEC_OUT

Q4216 UN2211

R4202 1k 1/10W

R4204 10k 1/10W

Q4217 XX JL4229

Q4214 2SK2036(TE85L)

IC4201 IP4776CZ38 HDMI INTERFACE PROTECTION

R4207 XX

R4210 4.7k 1/10W

X3001 13.5MHz

CONT VDD OUT
DDC +5V E DDC DAT DDC CLK NC CEC CLK-

R4245 33k 1/10W

RBRB4215 0

HDMI_CLKHDMI_CLK+

VH_DDH_1.8

VH_DDI

SDA_EMMA SCL_EMMA

VH_DDC

HDMI_CLK-

C4208 1000p 50V

C4210 1000p 50V

HDMI INPUT

CLK+ D0E D0+ D1E D1+ D2E D2+ CN4200 19P

RB4216 0

HDMI_D0+
HDMI_CLK+ HDMI_D0R4239 1k 1/10W R4240 1k 1/10W

R4243 R0 CHIP CHIP

R4247 XX C8926 XX

R4249 XX

HDMI_D0-

C4212 1000p 50V

RCHIP R1/10W R4254 R4255 10k 10k 1/10W 1/10W R4253 10k 1/10W C4216 1000p 50V R4256 10k 1/10W

R4251 XX

HDMI_D1HDMI_D1+ RB4217 0

HDMI_D0+ HDMI_D1-

VDDH(18)

VH_DDI TEST2 TEST1

C4213 1000p 50V

TEST12

H/CSYNC1

VSYNC1

VSYNC2

TEST13

VDDC(18) n.c.

VSYNC3

TEST7 TEST6

H/CSYNC3

H/CSYNC2

TEST10

VDDI(33)

TEST11

VH_DDH_3.3 HDMI_D1+ HDMI_D2-
C4204 1000p 50V HDM12_CLK+
VDDH(33) RXBC+ RXBCVSSH RXAC1RXAC1+ VDDH(33) RXBO+ RXBOVSSH RXAORXAO+ VDDH(33) RXB1+ RXB1VSSH RXA1RXA1+ VDDH(33) RXB2+ RXB2VSSH RXA2RXA2+ VDDH(33) WS AP0 AP1 AP2 AP3 ACLK VDDO(33) VSSO VDDC(18) VSSC CTL0 CTL1 CTL2 CTL3 VDDO(33) VSSO PL DE HS VS CS OR_R/CR OR_B/CB OR_G/Y VAI FREF
VDDA(33) VDDA(18) VSSA(PLL) VDDA(33) VSSA VSSA(R/PR) VDDA(33) VSSA R/PR1 R/PR2 R/PR3 REF_R/PR VDDA(33) VSSA SOG/Y1 SOG/Y2 SOG/Y3 VSSA(SOG/Y) VSSA VDDA(33) VSSA(G/Y) VDDA(33) VSSA G/Y1

VSSI SCL

VH_DDC C4250 1000p 50V C4217 1000p 50V

HDMI_D2-

HDM12_CLKHDMI_D2+

HDMI_D2+

C4201 0.1 16V

C4202 0.1 16V

VH_DDH_3.3 HDM12_D0+ C4258 1000p 50V HDM12_D0-

167 168

C4251 1000p 50V
D4204 MA111-TX VH_DDH_3.3 HDM12_D1+ D4203 MA111-TX FB4200 0uH IC4200 BR24L02F-WE2 BUS EEPROM

C4200 0.1 16V

R4212 10k 1/10W

C4259 1000p 50V

HDM12_D1-

C4218 1000p 50V

A1 A0 A2 E

VCC WP SCL SDA

R6053 1k 1/10W RN-CP

Q6007 MSB709-RT1
C6206 2200pF 1kV R CN6000 3P WHT

AC IN AC IN

R6205 100k 1W RS

C6210 1000p 630V

R6054 10k 1/10W RN-CP
D6203 ERA22-06AVRBT CM6000

CM6001

C6201 22p 2kV SL

C6207 330p 1kV

D6204 M1FL20U-4063 C6314 XX C10V R6218 XX R6219 XX R1/10W R6210 10k 1/10W
IC6200 STR-A6169 STANDBY SWITCHING REGULATOR

UDZSTE-174.7B

D6201 MMDL914T1 R6204 D6202 10ERB20-TB1/4W FPRD C50V

JW6200 5

FB6200 XX

FB6201 XX

C6209 470p 250V B
R6201 2.2 1W RS C6202 4.7 50V
C6203 C6204 1000p 10 50V 50V RCHIP
PH6200 PC123Y22JOOF PHOTOCOUPLER RCHIP C6208 0.1 16V R6207 1k 1/10W RCHIP

C6212 0.1 16V

R6209 33k 1/10W
IC6201 MM1431ATT(CN) SHUNT REGULATOR

R6211 10k 1/10W

~ G1 Board Schematic Diagram [ Power Supply ] Page 1/2 ~

- 46 -

AV-GND

AV_GN D

R_HP 1

PW_GND

IC6300 TDA7495S STEREO POWER AMPLIFIER

AUD_GND

R6309 1k 1/10W C6305 XX AUDIO_VCC

C6300 220p 50V

C6302 220p 50V
AUD_GND C25V C6307 0.1 50V FB6301 XX C35V C6311 0.022 25V R_IN FB6302 XX JRFB6303 XX C6313 0.01 50V JRJRFB6304 XX JR6316 0
R6306 120k 1/10W AUDIO_VCC R6304 120k 1/10W C50V

R6301 XX R6303 XX

C6312 0.01 50V
R6307 XX L_IN D6301 XX R6305 XX Q6301 XX C6306 0.22 16V AMP_MUTE D6300 UDZSTE-175.6B
C6310 0.022 25V Q6303 MSB709-RT1
AUDIO_VCC R6318 10k 1/10W D6302 UDZSTE-175.6B JW6300 15
R6300 XX R6302 XX R6312 XX

Q6300 XX

R6314 100k 1/10W
R6315 100k 1/10W RN-CP R6316 22k 1/10W

Q6302 MSD601-RST1 C50V

C6315 0.022 25V

R6317 10k 1/10W RN-CP

CN6300 4P
AUD_GND R6308 2.2k 1/10W RN-CP AUD_GND

R6311 XX R6310 XX

~ G1 Board Schematic Diagram [ Power Supply ] Page 2/2 ~

- 47 -

~ G1 Printed Wiring Board Conductor Side A ~
~ G1 Board Semiconductor Location Table Side A ~
DIODE D6014 D6015 D6018 D6202 D6203 D-5 D-7 C-7 I-7 H-6 IC6000 IC6001 IC6002 IC6200 IC I-3 G-3 F-3 I-6 IC6201 IC6300 F-7 C-4

D6000 D6008 D6011 D6013

K-6 I-4 E-6 D-7
TRANSISTOR Q6003 Q6004 I-5 H-5

- 48 -

~ G1 Printed Wiring Board Conductor Side B ~
~ G1 Board Semiconductor Location Table Side B ~
DIODE D6007 D6008 D6009 D6010 D6011 G-4 G-4 H-5 G-4 K-6 D6012 D6013 D6014 D6015 D6016 L-5 L-7 K-5 L-7 L-4 D6018 D6019 D6200 D6201 D6202 M-7 M-6 F-6 F-6 G-7 IC6000 D6203 D6300 D6302 IC G-4 H-6 N-4 M-5 IC6001 IC6002 IC6200 IC6201 IC6300 I-3 J-3 G-7 J-7 M-4 TRANSISTOR Q6000 Q6001 Q6002 Q6004 F-3 I-3 H-3 H-5 Q6005 Q6006 Q6007 Q6302 Q6303 N-7 M-7 M-7 N-4 M-5

R6002 R6007 220k 220k 1/10W R6003 1/10W 100k R6021 560k 1/10W D6000 MMDL914T1 R6005 470k 1/10W D6002 MMDL914T1 RCHIP RCHIP
Q6003 2SD1621-S C6036 0.1 50V R1/4W R6049 FPRD XX D6013 BAT54HT1
R6058 560k 1/10W R6059 560k 1/10W R6060 560k 1/10W C6037 XX R6061 470k 1/10W R6062 390k 1/10W

D6026 XX

D6029 XX
L6004 1uH LHL08 D6040 FCH08U10
RCHIP D6046 XX AUDIO_VCC D6047 XX
IC6000 FA5501AN-D1-TE1 ACTIVE PFC CONTROL FB COMP MUL IS

VCC OUT GND ZCD

C6050 XX

C6054 0.22 25V

Q6014 2SK3469

R6128 2.2M 1/4W

L6005 1uH LHL08

Q6004 2SD1621-S

R1/10W D6028 UF4005PKG23 R6089 XX D6032 CUMZ16NT106 25V

R6102 10k 1/10W

C6059 470p 1kV

R6106 0.22 2W RS

C6060 0.018 800V C35V

PS6301 4A CXX

D600 MMDL914T11 R6008 470k 1/10W R6009 47k 1/10W
R6024 R6051 22k 22k 1/10W 1/10W C6030 XX C6033 XX R6063 15k 1/10W R6064 1.5k 1/10W D6020 MMDL914T1 R1/10W RN-CP C50V

R6023 22k 1/10W

C6027 0.01 25V C6026 1000p 50V

R6107 0.22 2W

D6021 MMDL914T1

R6066 100k 1/10W

R1/10W D6040(1)

R6127 4.7 1/4W FPRD

Mount Mecha A6006

CN6005 13P

SIGNAL_VCC SIGNAL_VCC SIGNAL_VCC GND GND GND L GND R GND +33V GND AMP_MUTE

TO BDTR-2 BOARD CN6500

C6016 6800p 25V D6006 DTZ5.1B D6007 MMDL914T1

C6024 0.47 16V

407727701

D6019 MMDL914T1

R6053 330k 1/10W RN-CP R6054 22k 1/10W RN-CP

D6023 MA113-(TX)

RCHIP C6023 XX

R6081 2.2 1/4W FPRD

R6109 1k 1/10W RN-CP C6063 XX

MAIN FB

R6114 1k 1/10W RN-CP R6115 1k 1/10W RN-CP
R1/10W R6122 5.6k 1/10W C6064 R6118 0.022 4. 7 k 25V 1/10W
C6077 XX C6065 XX R0 1/4W FPRD L_I N R_I N

R6055 100k 1/10W RN-CP

R6123 XX

C6019 XX

PH6003 PC123Y22JOOF PHOTOCOCOUPLER IC6004 MM1431ATT(CN) SHUNT REGULATOR
D6048 UDZS-TE17-33B R6124 1k 1/10W RN-CP

C6078 XX AMP_MUTE

CARBON 0.47 5% 1/4W CARBON 4.7 5% 1/4W METAL 2.2M 2% 1/4W METAL 2.2M 2% 1/4W SHORT CHIP 0 SHORT CHIP 0 CARBON 820 5% 1/4W SHORT CHIP 0 FUSIBLE 10 5% 1/2W METAL OXIDE 2.2 5% 1W CARBON 330K 5% 1/2W CARBON 2.2 5% 1/4W METAL CHIP 220 5% 1/10W CARBON 2.2 5% 1/4W METAL CHIP 470 5% 1/10W METAL METAL METAL METAL SHORT CHIP 1.5K 5% 1/10W CHIP 100 5% 1/10W CHIP 10K 0.5% 1/10W CHIP 10K 0.5% 1/10W CHIP 0
R6131 1-216-864-11 R6132 1-249-416-11 R6133 1-216-295-91 R6200 1-212-958-00 R6201 1-216-353-00 R6202 R6203 R6204 R6205 R6206 R6207 R6208 R6210 R6211 R6217 R6218 R6304 R6306 R6308 R6309 R6313 R6314 R6315 R6316 R6317

- 69 -

METAL CHIP 27K 0.5% 1/10W METAL CHIP 12K 0.5% 1/10W CARBON 2.2 5% 1/4W METAL CHIP 10K 5% 1/10W METAL CHIP 10K 5% 1/10W METAL METAL METAL METAL METAL METAL METAL METAL METAL METAL CHIP 4.7K 0.5% 1/10W CHIP 47K 0.5% 1/10W CHIP 10K 5% 1/10W CHIP 10K 5% 1/10W CHIP 1M 5% 1/10W CHIP 47 0.5% 1/10W CHIP 4.7K 5% 1/10W CHIP 220K 0.5% 1/10W CHIP 3.3K 0.5% 1/10W CHIP 39K 0.5% 1/10W
1-260-129-11 1-249-385-11 1-216-813-11 1-249-385-11 1-216-817-11 1-216-823-11 1-216-809-11 1-218-871-11 1-218-871-11 1-216-295-91 1-216-295-91 1-216-864-11 1-216-864-11 1-216-825-11 1-216-049-11 1-216-864-11 1-216-845-11 1-216-845-11 1-216-837-11 1-216-833-11
SHORT CHIP 0 METAL CHIP 120K 5% 1/10W METAL CHIP 120K 5% 1/10W METAL CHIP 2.2K 5% 1/4W RES-CHIP 1K 5% 1/10W SHORT METAL METAL METAL METAL CHIP 0 CHIP 100K 5% 1/10W CHIP 100K 5% 1/10W CHIP 22K 5% 1/10W CHIP 10K 5% 1/10W
RES-CHIP 22 5% 1/10W METAL CHIP 1K 5% 1/10W METAL CHIP 10K 5% 1/10W METAL CHIP 1K 5% 1/10W RES-CHIP 22 5% 1/10W
Note : The components identified by mark contain confidential information. Strictly follow the instructions when ever the components are repaired and/or replaced

G2 H1/H1P BDTR-2

DESCRIPTION < VARISTOR > VARISTOR, VARISTOR, VARISTOR, VARISTOR, VARISTOR, REMARK

REF.NO. R6318

PART.NO DESCRIPTION REMARK 1-216-833-11 METAL CHIP 10K 5% 1/10W < RELAY > RELAY, POWER
REF.NO. VD9000 VD9001 VD9002 VD9003 VD9004 VD9005 VD9006

PART.NO

RY6000 1-755-579-11
< TRANSFORMER > CONVERTER TRANSFORMER (PIT) CONVERTER TRANSFORMER (PIT) TRANSFORMER, CONVERTER (SBT)
1-803-974-21 1-803-974-21 1-803-974-21 1-803-974-21 1-803-974-21 1-803-974-21 1-803-974-21
CHIP (1608) CHIP (1608) CHIP (1608) CHIP (1608) CHIP (1608)
T6002 1-443-983-11 T6003 1-443-986-11 T6200 1-443-313-21
VARISTOR, CHIP (1608) VARISTOR, CHIP (1608)

CN6000 CN6002 CN6003 CN6200 CN6300 D6000 D6004 D6005 D6006 D6007 D6008 D6009 D6010 D6011 D6012 D6013 D6014 D6015 D6018 D6019 D6023 D6200 D6201 D6202 D6203 D6204 D6300 D6302 ET6000
8-719-510-53 8-719-082-03 8-719-081-97 8-719-082-03 8-719-082-03 8-719-979-64 8-719-082-03 8-719-082-03 6-501-505-01 8-719-310-56 6-500-567-31 6-501-505-01 6-500-567-31 8-719-310-56 8-719-083-70 8-719-083-87 8-719-083-60 8-719-081-97 6-500-567-31 8-719-948-45 8-719-080-75 8-719-069-55 8-719-069-55
DIODE M1FL20U-4063 DIODE UDZSTE-175.6B DIODE UDZSTE-175.6B
< TERMINAL BOARD > TERMINAL BOARD, GROUND
1-537-770-21 < FUSE >
F6000 1-576-231-51 FH6000 1-533-725-11 IC6000 IC6001 IC6002 IC6200 IC6201 < IC >
FUSE 4A 250V FUSE HOLDER
6-705-810-01 6-709-368-01 6-709-368-01 6-709-368-01 8-759-586-17

IC IC IC IC IC

MCZ3001DB MM1431ATT(CN) MM1431ATT(CN) MM1431ATT(CN) TL1431CZ-AP

- 82 -

REF.NO. IC6300 PART.NO DESCRIPTION 8-759-831-57 IC TDA7495S < COIL > LINE FILTER COIL INDUCTOR 37MH INDUCTOR 10UH INDUCTOR 10UH LINE FILTER COIL INDUCTOR 100UH REMARK REF.NO. R6024 R6025 R6026 R6027 R6028 R6029 R6030 R6031 R6033 R6035 R6036 R6037 R6038 R6039 R6040 R6041 R6042 R6043 R6044 R6045 R6046 R6047 R6048 R6049 R6050 R6051 R6052 R6053 R6054 R6055 R6057 R6058 R6061 R6062 R6063 R6064 R6066 R6068 R6201 R6202 R6203 R6204 R6205 R6206 R6207 R6208 R6209 R6210 R6211 R6212

- 83 -

L6000 1-456-507-12 L6001 1-457-243-11 L6004 1-406-971-11 L6005 1-406-971-11 L6006 1-456-507-12 L6200 PH6000 PH6001 PH6002 PH6200 1-412-537-31
PART.NO DESCRIPTION REMARK 1-216-845-11 METAL CHIP 100K 5% 1/10W 1-216-833-11 METAL CHIP 10K 5% 1/10W 1-216-833-11 METAL CHIP 10K 5% 1/10W 1-216-837-11 METAL CHIP 22K 5% 1/10W 1-218-823-11 METAL CHIP 100 0.5% 1/10W 1-216-837-11 1-249-393-11 1-249-393-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-821-11 1-216-864-11 1-216-864-11 1-245-494-21 1-245-494-21 1-216-817-11 1-245-315-71 1-216-864-11 1-245-315-71 1-216-829-11 1-216-821-11 1-216-837-11 1-216-837-11 1-216-833-11 1-249-377-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-864-11 1-216-822-11 1-216-833-11 1-216-837-11 1-218-849-11 1-218-868-11 1-218-847-11 1-216-829-11 1-260-332-51 1-216-353-00 1-216-864-11 1-216-864-11 1-249-393-11 1-243-725-21 1-216-817-11 1-216-821-11 1-216-864-11 1-216-839-11 1-218-871-11 1-218-871-11 1-216-295-91 METAL CHIP 22K 5% 1/10W CARBON 10 5% 1/4W CARBON 10 5% 1/4W METAL CHIP 1K 5% 1/10W METAL CHIP 10K 5% 1/10W METAL CHIP 10K 5% 1/10W METAL CHIP 1K 5% 1/10W SHORT CHIP 0 SHORT CHIP 0 METAL 2.2M 2% 1/4W METAL 2.2M 2% 1/4W METAL CHIP 470 5% 1/10W METAL OXIDE 0.1 5% 2W SHORT CHIP 0 METAL OXIDE 0.1 5% 2W METAL METAL METAL METAL METAL CHIP 4.7K 5% 1/10W CHIP 1K 5% 1/10W CHIP 22K 5% 1/10W CHIP 22K 5% 1/10W CHIP 10K 5% 1/10W