Adjusting Your Setup (MENU) Introducing the menu system.. 34 Changing the Picture setting. 38 Changing the Sound setting. 41 Operating the Multi Picture using the Menu.. 44 Changing the Setup setting.. 45 Additional Information Troubleshooting.. 57 Self-diagnosis function.. 61 Identifying parts and controls. 62 Specifications.. Backcover

Getting Started

Step 1
Install the projection TV
For the best picture quality, install the projection TV within the areas below.
Optimum viewing area (Horizontal)

KP-FX432

min. 1.9 (566f 7 m (. t f.).) t

KP-FX532

min. (8 ft 2.4 m.)
Optimum viewing area (Vertical)

min. 1.9 (6 ft m.)

min. 2.4 (8 ft m.)

Step 2

Connect the antenna
If you wish to connect a VCR, see the Connect a VCR diagram on page 8.

Rear of projection TV

Antenna cable (not supplied)
Antenna cable (not supplied) : Signal flow

For optimum Performance

To connect the projection TV to the antenna or the VCR, use an antenna cable (not supplied). Note that one end of the cable has a male plug fitted while the other end is fitted with a female socket. Connect the male plug to the 8 (antenna) terminal of the projection TV.
CAUTION Do not connect the power cord until all other connections are complete; otherwise, a minimal current leakage through the antenna or other terminals to the ground could occur.
continued Using Your New Projection TV
Getting Started (continued)

Connect a VCR

To play a video tape, press t (see page 17).
To 8 (antenna) Antenna cable (not supplied) Rear of projection TV

To antenna output

To (S video input)
AUDIO R VIDEO IN VIDEO OUT L
S video cable (not supplied)

PB/ CB PR/ CR

(MONO)

Y G PB/ CB B PR/ CR R

HD SYNC VD
To video and audio outputs

To S video output

: Signal flow
Audio/Video cable (not supplied)
To t 1, 2 or 3 (video input) (yellow) -L (MONO) (white) -R (red)
Notes If you connect a monaural VCR, connect the yellow plug to (the yellow jack) and the black plug to -L (MONO) (the white jack). If you connect a VCR to the 8 (antenna) terminal, preset the signal output from the VCR to the program number 0 on the projection TV. When you connect a VCR to the S video input, display the Setup menu and select Auto for S Input (see page 47). If the signals are input to both (S video input) and (video input), the S video signal is automatically selected. To view the video signal input to (video input), select Off for S Input.

Step 3

Insert the batteries into the remote
Note Do not use old batteries or different types of batteries together.

Step 4

Set up your projection TV automatically

DRC-MF

PRO G+

PROG INDEX

HD/DVD
Press ! to turn on the projection TV. The Initial Setup menu appears, and you can select the on-screen language.
I n i t i a l Se t u p Lan g u a g e : En g l i s h

Se l e c t :

Co n f i r m:

En d :

Move up or down to select the desired language, then press. Start auto program now? appears.
F i r s t p l e a s e c on n e c t c a b l e / a n t en na S t a r t a u t o p r o g r am n ow?
Move up or down to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress. After channel presetting is complete, automatic convergence adjustment menu appears.
P r o g r am : TV Sy s t em: Au t o VHF L ow :
S t a r t d i g i t a l q u i c k f o c u s n ow? Yes No Se l e c t : Co n f i r m : End :

I n i t i a l Se t u p

Yes No Co n f i r m :

Au t o Pr o g r am

Co n f i r m : I n i t i a l Se t u p

continued

Make sure that Yes is selected, then press The convergence adjustment screen appears, and the convergence is automatically adjusted. The last Initial Setup menu appears.
I n i t i a l Se t u p D i s p l a y t h i s menu n e x t t i me? Yes No Se l e c t : Co n f i r m : End :
up or down to select No, then press
The Initial Setup menu will not appear again the next time you turn on the projection TV by pressing !. To allow this menu to appear again, select Yes, then press.
Tip If your projection TV has preset an unwanted channel or cannot preset a particular channel, then preset your projection TV manually (see page 49). Notes If you want to cancel any setup, move up or down to select No and press , or press MENU. Convergence is also adjusted manually using the menu (see page 48). You can also perform the Digital Quick Focus feature using on the front panel. Sound will mute while the Digital Quick Focus feature is running. The MENU, 2 + or and (Enter) buttons on the projection TV can be also used for the above operations instead of and MENU buttons on the remote control.
Connecting optional components
You can connect optional audio/video components, such as a VCR, a DTV (Digital Television) receiver, multi disc player, camcorder, video game, or stereo system. To watch and oprate the connected equipment, see pages 17 and 31.

R-AUDIO-L

LINE OUT
To t 1, 2, or 3 (video input) DVD player
: Signal flow (yellow) -L (MONO) (white) -R (red)
Notes Since the high quality pictures on a DVD disc contain a lot of information, picture noise may appear. In this case, display the Picture menu and select Personal for Picture Mode, then adjust the sharpness (Sharpness) under Picture Adjustment (see page 40). (S video input) on the projection You can also connect a DVD player to TV.
Connecting a DTV (digital television) receiver to 1 or 2 (component video input) jacks
Rear of projection TV Component video cable (not supplied) To 1 or 2 (Component video input)
To component video output Digital TV receiver To audio outputs
Audio cable (not supplied) To
Note The projection TV is equipped with the G/B/R/HD/VD inputs. If your DTV receiver is equipped with the Y/PB/PR output connectors, connect it to the Y/PB/PR connectors of 1 or 2. Connect nothing to the HD/VD connectors of 2. If your DTV receiver is not equipped with the Y/PB/PR output connectors, connect it to the G/B/R/HD/VD connectors of 2. Tip The projection TV accepts the following signal formats: Total scanning line 1125i 750p 625p 625i 525p 525i Effective scanning line 1080i 720p 576p 576i 480p 480i fV (Hz) 50/60 50/60

Watching the TV

This section explains various functions and operations used while watching the TV. Most operations can be done using the remote.

1 indicator

Number buttons JUMP

PROG +/

OPTION RESET
Press ! to turn on the projection TV. When the projection TV is in standby mode (the 1 indicator on the projection TV is lit red), press !/1 on the remote. Press PROG +/ or the number buttons to select the TV channel. For double digit numbers, press -/--, then the number (e.g., for 25, press -/--, then 2 and 5).
Note When you turn on the projection TV, either the program number or video mode is displayed for approximately 40 seconds. The Eco Mode ( ) icon will also appear if Eco Mode in the Setup menu is set to On (see page 47).

01GB05GET.p65

10/8/03, 11:39 AM
To select a projection TV program quickly
1 Press and hold PROG +/. 2 Release PROG +/ when the desired program number appears.
Note When you select a TV program quickly, the picture may be disrupted. This does not indicate a malfunction.

Additional tasks

To Turn off temporarily Press @/1. The 1 indicator on the projection TV lights up red. ! on the projection TV. 2 +/. %. t (or t on the projection TV) to select VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, HD/DVD 1 or HD/DVD 2. To return to the TV screen, press a (or t on the projection TV). HD/DVD to select HD/DVD 1 or HD/DVD 2. To return to the TV screen, press a (or t on the projection TV). JUMP.

Stereo

A2 (German) bilingual
Receiving area for NICAM and A2 (German) programs
System NICAM A2 (German) Receiving area Hong Kong, Singapore, New Zealand, Malaysia, Thailand, etc. Australia, Malaysia, Thailand, etc.
Notes If the signal is very weak, the sound becomes monaural automatically. If the stereo sound is noisy when receiving a NICAM program, select Mono. The sound becomes monaural, but the noise is reduced. Before receiving a NICAM stereo program in China, please check the NICAM broadcast condition at your area. When receiving a NICAM stereo program, the receiving conditions might vary depending on area. In addition, different strength of the NICAM broadcast signal might affect the receiving quality.
If the sound is distorted or noisy when receiving a monaural program through the 8 (antenna) terminal
Press A/B repeatedly until Mono appears on the screen. To cancel the monaural sound setting, press A/B again until Auto appears on the screen.

Mono Auto

Notes The Mono or Auto setting is memorized for each program position. You cannot receive a stereo broadcast signal when the projection TV is in the Mono setting. Normally, set the projection TV to Auto.

Viewing Teletext

Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news.

Number buttons

(red, green, yellow, blue) PROG +/

Displaying Teletext

Select a TV channel that carries the Teletext broadcast you want to watch. Press text. to display the
P166 SECTEXT 166 FR1 MAR 03:59:09 From Singapore Day 1.6 To PARIS To OSAKA To ROMA To SYDNEY 2.5 4.6 2.1 2
A Teletext page (normally the index page) is displayed. If there is no Teletext broadcast, 100 is displayed at the top left corner of the screen.
Dep/Arr 220/0588 2130/1225 2115/1330 1000/1715 0930/2015 2130/0745 2300/0915 2210/0610 2100/0835
Flight Alrcraft SQPA115 L15 SQSQ6 CX522 SQ24 AZ487 SQ21A SQ21A 747 L747

Language Convergence Digital Quick Focus Manual Adjust Channel Setup Auto Program Manual Program TV System Program Label Program Block Wide Mode
Program Edit Changes the order of the preset channels. Activate or deactivate Wide Mode feature. Activate or deactivate GAME MODE feature. Assign labels to the audio/video equipment connected to the projection TV. Select the input to which the audio/video equipment is connected. Video 1 t Video 2 t Video 3 t Video 4 t HD/DVD 1 t HD/DVD 2 Selects one of the prefixed labels or assign your own label in Edit position. Video 1 t VCR t SAT t Game t Edit Selects the color system: Auto t PAL t SECAM t NTSC3.58 t NTSC4.43 Activates or deactivates ECO MODE feature. Selects the S video input mode: Auto or Off
Game Mode Video Label Video Input

Color System

Eco Mode S Input
continued Adjusting Your Setup (MENU)

01GB08ADJ.p65

Introducing the menu system (continued) To restore the factory settings
Press the RESET button on the remote. The settings other than the following items in the menu can be reset by using the RESET button: Language Convergence Program and Skip in Manual Program Fine in Manual Program TV System Personal in Picture mode/Sound mode Program Label Video Lavel
36 Adjusting Your Setup (MENU)

How to use the menu

Press MENU to display the menu.
Pi c t ure DRC - MF : DRC P i c t u r e M o d e : Pe r s o n a l P i c t u r e Ad j u s t men t 3D - NR : Off
Move the button joystick ( ) up, down, left or right to select the desired item. Press the button joystick ( ) to confirm the selection and/or go to the next level.

Mu l t i P i c t u r e

Twi n : On Swap P r o g r am I n d e x
Tw i n : On Swap P r o g r am I n d e x

Other menu operations

To Adjust the setting value Move to the next/previous menu level Cancel the menu Press/Move Move Move up, down, left or right. left or right.

Press MENU.

Tips If you want to exit from Menu level 2 to Menu level 1, move up or down until the return icon (3) is highlighted, then press. The MENU, (Enter), and 2 + or buttons on the projection TV can also be used for the operations above. Note If more than 90 seconds elapse between entries, the menu screen automatically disappears.
Changing the Picture setting
The Picture menu allows you to: adjust the picture setting, view higher quality pictures and reduce picture noise.
Pi c t ure DRC - MF : DRC P i c t u r e Mod e : Pe r s o n a l P i c t u r e Ad j u s t men t 3D - NR : Off

Move select

up or down to , then press.

Pi c ture

DRC1250 DRC-MF: P i c t u r e M od e : P e r s o n a l P i c t u r e Ad j u s t men t 3 D - NR: Off
Move up or down to select the desired option (see the table below), then press.
DRC-MF: DRC1250 P i c t u r e Mode : Pe r sDn a l100 o RC P i c t u r e Ad j u s t mP no g r es s i v e er t 3 D - NR : Off

Select DRC-MF

To activate the Digital Reality Creation-Multi function feature to display higher quality pictures. Move up or down to select DRC1250, DRC100 or Progressive, then press. receive suitable picture mode. Move up or down to select Dynamic, Standard, Hi-Fine, Personal*, then press.

Picture Mode

* When the Personal mode is selected, the last adjusted picture setting in the Picture Adjustment menu is received (see page 40).
38 Adjusting Your Setup (MENU)
Select Picture Adjustment
To adjust the picture quality when Picture Mode is set to Personal.
P i c t u r e Ad j u s t me n t Pi c t u r e 80 Br i g h t n e s s 50 Co l o r 50 Hue 00 Sha r p n e s s 50 Co l o r Tempe r a t u r e : Neu t r a l Res e t Se l e c t : Co n f i r m : End :
improve the picture quality of TV or video if a signal received is weak. Move up or down to select On, then press. To cancel, select Off, then press.
Tips For details on the options under the DRC-MF and Picture Mode modes, see pages 19 and 20, respectively. When high-definition (HD) or progressive signals are input, DRC-MF does not function.

Move up or down to select one of the prefixed labels, then press. To assign your favorite label, see page 56.
Vi d e o I n p u t : V i de o 1 VCR La b e l :
To assign labels to other equipment, select Video Input, then repeat steps 2 to 4.
Changing the Setup setting (continued) To assign your favorite label
1 Follow steps 1 to 3 on the page 55 and select Edit in step 4, then press. 2 Move up or down to scroll through the label characters (A to Z, 0 to 9, etc.), then press to confirm the highlighted character.
V i d e o La b e l Vi d e o I n p u t : V i de o 1 V i deo 1 La b e l : VCR SAT Game Ed i t [ V _ _ _ _ ] Se l e c t : Co n f i r m : End :
To insert a blank, leave _ and move right. To change the confirmed character, move left to highlight it, then move up or down to select the correct character. 3 Repeat step 2 to add up to 5 characters to the label.
56 Adjusting Your Setup (MENU)

Additional Information

Troubleshooting
If you have any problem while viewing your projection TV, please check the following troubleshooting guide. If the problem persists, contact your Sony dealer.

Symptom

Snowy picture
Possible cause The connection is loose or the cable is damaged. Channel presetting is inappropriate or incomplete.
Solutions Check the antenna cable and connection on the projection TV, VCR and on the wall.

Page 7

Noisy sound
Display the Channel Setup menu under the Setup menu and select Manual Program to preset the channel again. Check the antenna type (VHF/UHF). Contact a Sony dealer for advice. Adjust the antenna direction. Contact a Sony dealer for advice. Try using a booster. Display the Channel Setup menu under the Setup menu and select Manual Program. Then, select Sensitivity: Low. Turn off or disconnect the booster if it is in use.
The antenna type is inappropriate. The antenna direction needs adjustment. Signal transmission is low.

Distorted picture

Broadcast signals are too strong.

Good picture

The TV system setting is inappropriate.
If the sound of all the channels are noisy, display the Channel Setup menu under the Setupmenu and select Auto Program to preset the channels again. If the sound of some channels is noisy, select the channel, then display the Channel Setup menu under the Setupmenu and select the appropriate TV system (TV System).
The sound of the right picture is selected when TWIN pictures are displayed.

Press

Troubleshooting (continued)

No picture

Possible cause The power cord, antenna or VCR is not connected.
Solutions Check the power cord, antenna and the VCR connections.

No sound

The projection TV is not Press I/1 on the remote. turned on. Press ! on the projection TV to turn off the projection TV for about five seconds, then turn it on again.
The volume level is too low. The sound is muted. The broadcast signal has a transmission problem. The sound of the right picture is selected when TWIN pictures are displayed.
Press 2 + to increase the volume level. Press % to cancel the muting. Press A/B until a better sound is heard. Press or.

Dotted lines or stripes

There is local interference from cars, neon signs, hair dryers, power generators, etc.
Do not use a hair dryer or other equipment near the projection TV. Adjust the antenna direction for minimum interference. Contact a Sony dealer for advice.

Double images or ghosts

Broadcast signals are reflected by nearby mountains or buildings. The antenna direction needs adjustment. Use of a booster is inappropriate.
Use a highly directional antenna. Use the fine tuning (Fine) function.

50 40

Adjust the antenna direction. Contact a Sony dealer for advice. Turn off or disconnect the booster if it is in use. Display the Picture menu and select Personal of Picture Mode, then adjust the Color level under Picture Adjustment. Display the Setup menu and check the color system (Color System) setting (usually set this to Auto). Adjust the antenna direction. Contact a Sony dealer for advice.

No color

The color level setting is too low.
The color system setting is inappropriate. The antenna direction needs adjustment.
58 Additional Information
Projection TV cannot receive stereo broadcast signal.

Possible cause

Solutions

Page 28 22

The stereo reception Press A/B until Auto appears on setting is inappropriate. the screen. The sound of the sub picture is selected when TWIN pictures are displayed. The connection is loose or the cable is damaged. The antenna direction needs adjustment. The broadcast signal has a transmission problem. The channel carries no Teletext broadcast. Press or.

Stereo broadcast sound switches on and off or is distorted. or The sound switches between stereo and monaural frequently. 100 appears at the top of the screen after approximately 10 seconds and there is no Teletext display. Teletext display is incomplete (snowy picture or double images).
Check the antenna cable and connection on the projection TV, VCR and on the wall. Adjust the antenna direction. Contact a Sony dealer for advice. Press A/B until a better sound is heard.
Connection is loose or the cable is damaged. The antenna direction is inappropriate. Signal transmission is too low.
Check the antenna cable and connection on the projection TV, VCR, and at the wall. Adjust the antenna direction. Contact a Sony dealer for advice. Try using a booster. Use the fine tuning (Fine) function. Use the fine tuning (Fine) function.

50 50

Lines moving across the TV screen.
There is interference from external sources, e.g., heavy machineries, nearby broadcast station.
continued Additional Information
Cannot play shooting games.
Possible cause Some shooting games which involve pointing a light beam at the projection TV screen with an electronic gun or rifle cannot be used with your TV. For detail, see the instruction manual supplied with the video game software. Changes in room temperature sometimes make the projection TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. This is the same static discharge that is felt when touching metal door handles or car doors especially when the air is dry, for example in winter. This does not indicate a malfunction.

Page _

Projection TV cabinet creaks.
Static discharge is felt when touching the projection TV cabinet.
60 Additional Information

Self-diagnosis function

Your projection TV is equipped with a self-diagnosis function. If there is a problem with your projection TV, the 1 (standby) indicator flashes red. The number of times the 1 indicator flashes indicates the possible causes.
Check that the 1 indicator flashes red a number of times between 3-second intervals. Count the number of times the 1 indicator flashes. Press ! (main power) to turn off your projection TV. Inform your nearest Sony service center about the number of times the 1 indicator flashed. Be sure to note the model name and serial number located on the rear of your projection TV.

Identifying parts and controls
Front and inside the drop-down panel

Front panel

Inside the drop-down panel
Button/connector 1! 2 PROG +/ +/ 4t 5 MENU 8i 9 t4( q; t 4 (

) , L(MONO)

Function Turn off completely or turn on the TV. Select program number. Adjust volume. Select items in the menu. Select TV or video input. Display the menu. Confirm selected items. Adjust convergence automatically. Headphone jack Connect to S video output of video equipment. Connect to video/audio outputs of equipment.

Page 11 11

62 Additional Information
Function Page Connect to S video output of 8 video equipment. t 1/t 2/t 3 Connect to video/audio 8 outputs of video equipment. T Connect to video/audio inputs 12 of audio/video equipment. 1 Connect to component video 13 outputs on a DVD player. 2 Connect to component video 13 outputs on a DVD player. Connect to a digital TV receiver 15 equipped with the G/B/R/HD /VD outputs. SYNC HD/VD Connect to HD/VD outputs 15 on a digital TV receiver. 8 Connect the antenna cable. 7

Connector

Identifying parts and controls (continued)

Remote control

Label color White Green Yellow Pink Button function For general TV operations For Teletext operations For TWIN picture operations For optional components operations
64 Additional Information

Button ?/1 2

% 4 HD/DVD 5 t
6 a 9, 8 JUMP 9 PROG +/ q;

qs 2 +/

Function Turn off temporarily or turn on the projection TV. Display on-screen information. Reveal Teletext concealed information. Mute the sound. Select component input. Select TV or video input. Stop Teletext page from Scrolling. Display the TV program. Turn off Teletext. Input numbers. Jump to previous channel. Select program number. Set the projection TV to turn off automatically. Show TV screen while waiting for Teletext page. Set the projection TV to turn on automatically. Display Teletext service contents. Adjust volume.

Page 17

), , , ( /+ PROG
P166 SECTEXT 661 FR1 MAR 90:95:30

. ) ( . , 001 .

From Singapore Day 6.1 To PARIS To OSAKA To ROMA To SYDNEY 5.2 6.4 7.1 2
Dep/Arr 8850/022 5221/0312 0331/5112 5171/0001 5102/0390 5470/0312 5190/0032 0160/0122 5380/0012
Flight Alrcraft 82SQ 747 511PA 51L 62SQ 747 6SQ 225CX 42SQ 784AZ SQ21A SQ21A 747 01L 747 747
. , : T T. . . , .* , . , /+ PROG . z . , . . , . . , : T T. , . , .

)( ) (

), (

* .

FASTEXT
FASTEXT . ,FASTEXT . - ) (. , ,

FASTEXT

- . .

1/VIDEO I

,Beta , VHS DVD.
, : 1/@ ,VIDEO 0 , ) (.
1/@ VIDEO 1/@ VIDEO 1/@ VIDEO 1/@ VIDEO 1/@ VIDEO 1/@ VIDEO 1/@ VIDEO
DVD )VTR1 (Beta )VTR2 (8mm )VTR3 (VHS MDP CD MD

, .

) (N 1/@ VIDEO , ,OPTION ) ,(X ) ,(x ).(, )>( ) (.
/ 1/@ VIDEO N OPTION . x OPTION . > OPTION . . OPTION . X OPTION . . > . OPTION . . / )(M )(m ) (M )(m

DVD

/ 1/@ VIDEO N OPTION . x OPTION . X OPTION . . /

> . OPTION .

MDP
/ 1/@ VIDEO N OPTION . x OPTION . X OPTION . . > . OPTION . . /

CD MD

MENU . .
Picture Sound Multi Picture Setup
Se t u p En g l i s h : La n g u a g e Convergence Channel Setup Auto :Wide Mode Gam e Mod e : Of f Vi d e o L a b e l Co l o r S y s t em: Au t o : Se l e c t : Co n f i r m : End

Navigation Help

Setup ) (, ) (.
Cha n n e l S e t u p Au t o P r o g r am Manua l P r o g r am TV S y s t em:B/G P r o g r am L a b e l P r o g r am B l o c k P r o g r am Edit : Se l e c t : Co n f i r m : End Au t o P r o g r am : P r o g r am TV Sy s t em: Au t o : VHF L ow

: Co n f i r m

/ / DRC-MF : 0521Progressive T DRC100 T DRC : Personal T Hi-Fine T Standard T Dynamic Personal : T Hue T Color T Brightness T Picture Reset T Color Temperature T Sharpness . : Personal T Soft T Drama T Dynamic Personal : Reset T *BBE T Bass T Treble . Surround : Off T Simulated T TruSurrond
/ DRC-MF Picture Mode Picture Adjustment 3D-NR Sound Mode Sound Adjustment Balance Surround

Picture

Intelligent Volume .
* BBE Sound USP . BBE BBE BBE Sound.

) (MENU

/ / . . . ) ( )( T : ) English( T . . . . , . Auto Program . .
/ Swap Program Index Language Convergence Digital Quick Focus Manual Adjust Channel Setup Auto Program

Twin Multi Picture

Manual Program Manual Program . . : M T D/K T I T B/G ) ( . . TV System Program Label Program Block Program Edit Wide Mode Game Mode Video Label Video Input

. WIDE MODE . GAME MODE . / . / . 1 T Video 4 T Video 3 T Video 2 T Video 1 HD/DVD 2 T HD/DVD Edit . 1 Edit T Game T SAT T VCR T Video : T NTSC3.58 T SECAM T PAL T Auto 34.4NTSC .ECO MODE S : Auto Off
RESET . RESET : Language Convergence Program Skip Manual Program Fine Manual Program TV System Personal Picture Mode Sound Mode Program Label- Video Label

Pi c t ure

: DRC - MF DRC P i c t u r e Mod e : Pe r s o n a l P i c t u r e Ad j u s t men t : 3D - NR Off

MENU .

)3(
, . , ) (, + 2 ,MENU . , .
: Twi n On Swap P r o g r am I n d e x

) ( , , .

: Tw i n On Swap P r o g r am I n d e x

) ( .

/ , , . . .MENU /

Picture

, .
Pi c t ure : DRC - MF DRC P i c t u r e Mod e : Pe r s o n a l P i c t u r e Ad j u s t men t : 3D - NR Off

MENU .

0521DRC :DRC-MF P i c t u r e Mode : Pe r s o n a l P i c t u r e Ad j u s t men t :3 D - NR Off

, .

:DRC-MF 0521DRC 001P i c t u r e Mode : Pe r sDn a l o RC P i c t u r e Ad j u s t mP no g r es s i v e er t :3 D - NR Off

) (, .

. 0521 DRC100 ,DRC . *Progressive , . ,Hi-Fine ,Standard ,Dynamic . *Personal ,
* Personal , Picture Adjustment ) (.
Picture Mode Personal .
P i c t u r e Ad j u s t me n t Pi c t u r e 08 Br i g h t n e s s 05 Co l o r 05 Hue 00 Sha r p n e s s 05 Co l o r Tempe r a t u r e : Neu t r a l Res e t : Se l e c t : Co n f i r m : End

Picture Adjustment

. On , . . , Off ,
DRC-MF ,Picture Mode , . - ) (HD , DRC-MF .

Picture ) (

Picture Adjustment
Personal Picture Mode Picture Adjustment . Picture Personal Picture Mode.
Pi c t u r e 08 Br i g h t n e s s 05 Co l o r 05 Hue 00 Sha r p n e s s 05 Co l o r Tempe r a t u r e : Neu t r a l Res e t : Se l e c t : Co n f i r m : End

Picture Adjustment , .

) ,(Color .

,

Picture Brightness Color *Hue Sharpness Color Temperature Reset
Natural ,Cool Warm . Reset .

* Hue NTSC.

. Personal .

Sound

Sound . .

. MENU

, .
S o u n d Mo d e : D y n am i c So u n d Ad j u s t menD r ama t 5f B a l a nc e So 0 t I n t e l l i g e n t Vo l umeeOs o na l P:r f f S u r r ou n d : O f f Se l e c t : Co n f i r m : End :

) (, .

/ 1 ! 2 /+ PROG 3 /+ t 5 MENU 8 i (4t 9 )

0 , (4t )L(MONO)/R

S. /. / /. .DVD .DVD /G/B/R/HD.VD HD/VD . .

3 t 1/t 2/t 3 T 5 2

6 SYNC HD/VD 7 8

TWIN

. . . . . . . . . . . . . . . .

1 1/? 2

% 4 HD/DVD t 7
6 a 0, - 8 JUMP 9 /+ PROG ;q

;q qa qs

2 +/ qs
. . .DRC-MF /. . . . , . PROGRAM.INDEX . . .TWIN . . . .FASTEXT . .FASTEXT . .FASTEXT . .FASTEXT . .

VIDEO ?/1 qd

DRC-MF qf A/B qg

PROG INDEX qh qk

MENU qj

qg qh qj qk ql ;w

.

ql ;w wa 7

ws )( )( )( )( wd

RESET wj OPTION wk

,

, , , ,

(KP-FX432/532 M91) , , (KP-FX432 M31) ,

, ,

KP-FX532 KP-FX432

, , 8

,t 1 -L (MONO) -R

, ,8 ,

(MONO) L S , S ,

! Initial ,Setup ? , ,

Sel e c t :

Con f i rm:

, , , !

, (Enter)

2 + ,MENU MENU

t4 -L (MONO) -R :

,t 1 ,

-L (MONO) -R

HD/DVD 2 HD/DVD 1 T

-L DVD -R
Y PB B-Y ,Cb PR R-Y ,Cr 1 , DVD HD/VD

Y PB/CB PR/CR 2

HD/DVD 2 HD/DVD 1 t , ,

DVD DVD

-L -R :
G/B/R/HD/VD ,Y/PB/PR DTV Y/PB/PR 2 HD/VD ,Y/PB/PR DTV 2 G/B/R/HD/VD
: 1080i 720p 576p 576i 480p 480i 1125i 750p 625p 625i 525p 525i

! !/1

PROG +/ , , 5

-/--/--

PROG +/ PROG +/
1 @/1 ! 2 +/ % , , , t HD/DVD 2 HD/DVD 1 , t a , t ,

HD/DVD 2 HD/DVD 1 t a ,

HD/DVD ,DVD DTV JUMP *

!/1

, , , ,

DRC-MF

(DRC-MF)

Progressive

Progressive

, , ,

/ TWIN PROG +

DVD HD HD ,

HD HD

, HD

(TWIN PROG +/)

(TWIN PROG +/) (PAP)

(TWIN PROG +/)

PAP HD PAP HD PAP ,HD

PROG INDEX

, ,

PROG INDEX

*TruSurround

SRS Labs, Inc SRS Labs, Inc
SRS TruSurround * SRS TruSurround

, , ,

A/B , A/B
From Singapore Day 1.6 To PARIS To OSAKA To ROMA To SYDNEY 2.5 4.6 2.Dep/Arr 220/0588 2130/1225 2115/1330 1000/1715 0930/2015 2130/0745 2300/0915 2210/0610 2100/0835 Flight Alrcraft SQPA115 L15 SQSQ6 CX522 SQ24 AZ487 SQ21A SQ21A 747 L747