2-887-146-E2 (1)

Trinitron Color TV

Operating Instructions
Before operating the unit, please read this manual thoroughly and retain it for future reference.

KV-SZ29

2006 Sony Corporation
01GB01COV-SOEMRus.p65 Black
Sony KV-SZ29M91K Group A11 (GB dummy) _2-887-146-E2 (1)

15/8/07, 9:19 am

WARNING
Dangerously high voltages are present inside the TV. TV operating voltage: V AC. Do not plug in the power cord until you have completed making all other connections; otherwise a minimum leakage current might flow through the antenna and other terminals to ground. To avoid battery leakage and damage to the remote, remove the batteries from the remote if you are not going to use it for several days. If any liquid leaks from the batteries and touches your skin, immediately wash it away with water.
For your own safety, do not touch any part of the TV, the power cord and the antenna cable during lightning storms.
For childrens safety, do not leave children alone with the TV. Do not allow children to climb onto it.
To prevent fire or shock hazard, do not expose the TV to rain or moisture.
Do not place any objects on the TV. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
Do not operate the TV if any liquid or solid object falls into it. Have it checked immediately by qualified personnel only.
Install the TV on a stable TV stand and floor which can support the TV set weight. Ensure that the TV stand surface is flat and its area is larger than the bottom area of the TV.
Do not block the ventilation openings of the TV. Do not install the TV in a confined space, such as a bookcase or built-in cabinet.
Your TV is recommended for home use only. Do not use the TV in any vehicle or where it may be subject to excessive dust, heat, moisture or vibrations.
Do not plug in too many appliances to the same power socket. Do not damage the power cord.
Do not open the cabinet and the rear cover of the TV as high voltages and other hazards are present inside the TV. Refer servicing and disposal of the TV to qualified personnel.
Clean the TV with a dry and soft cloth. Do not use benzine, thinner, or any other chemicals to clean the TV. Do not attach anything (e.g., adhesive tape, cellophane tape, glue) on the painted cabinet of the TV. Do not scratch the picture tube.
Pull the power cord out by the plug. Do not pull the power cord itself. Even if your TV is turned off, it is still connected to the AC power source (mains) as long as the power cord is plugged in. Unplug the TV before moving it or if you are not going to use it for several days.
01GB02WAR-SOEMRus.p65 Black

15/8/07, 9:20 am

Table of Contents

Installation

Securing the TV. 4 Getting Started.. 5 Setting up your TV (Initial Setup). 6

Menu Adjustment

Introducing the WEGA GATE navigator.. 17 Settings Adjustment.. 18 Changing the Picture setting. 19 Changing the Sound setting. 21 Changing the Channel Setup setting.. 22 Changing the Setup setting.. 24

Overview of Controls

TV front and rear panels. 8 Using the remote control and basic functions.. 9
GB Additional Information
Connecting optional components. 25 Troubleshooting.. 27 Specifications.. Back cover

Advanced Operations

Selecting the picture and sound modes.. 11 Enjoying the Dynamic 5-Band Visualizer.. 12 Enjoying the Party Mode. 13 Listening to the FM Radio. 14 Enjoying stereo or bilingual programs.. 15 Viewing Teletext.. 16
Made in Malaysia. Manufacturer: Sony Corporation Address: 1-7-1 Konan, Minota-ku, Tokyo 108-0075, Japan.

01GB03TOC-SOEMRus.p65

x Securing the TV
To prevent the TV from falling, use the supplied screws, clamps and band to secure the TV.
20 mm 3.8 mm screws clamps band
Screw the band to the TV stand and to the provided hole at the rear of your TV.
(1) Put a cord or chain through the clamps. (2) Screw one clamp to a wall or pillar and the other clamp to the provided hole at the rear of your TV.
(1) Attach each end of a cord or chain to the provided holders at the rear of your TV. (2) Securely fix the attached cord or chain to a wall or pillar using an attachment which can support the TV set weight.
Note Use only the supplied screws. Use of other screws may damage the TV.
01GB04INS-SOEMRus.p65 Black

15/8/07, 9:21 am

x Getting Started

Step 1

Insert the batteries (supplied) into the remote.

01GB04INS-SOEMRus.p65

5 Black
Note Do not use old or different types of batteries together.

Step 2

Connect the antenna cable (not supplied) to 8 (antenna input) at the rear of the TV.
Tips Your TV can receive both TV and FM radio signal from the appropriate connections through the 8 (antenna input) terminal (see page 25). You can also connect your TV to other optional components (see page 25).

Step 3

Plug in the power cord, then press ! on the TV to turn it on.
Note The 1 (standby) indicator flashes green for a few seconds when turning on the TV. This does not indicate a malfunction.

Step 4

Set up the TV by following the instructions of the a (Initial Setup) menu (see page 6).
x Setting up your TV (Initial Setup)
When you turn on your TV for the first time, the a (Initial Setup) menu will appear. You may change the menu language, preset the TV channels automatically, sort or edit the channels and adjust the picture position using the buttons on the remote control or TV front panel.
Press V or v to select the desired menu language, then press. The selected menu language appears.

Select Confirm

Press V or v to select Yes, then press to preset the channels automatically. The screen will indicate automatic presetting is in progress.

Select Confirm End

After all available channels have been tuned and stored, the Program Sorting/Edit menu appears automatically on the screen. To skip automatic channel presetting, select No, then press. If the message No channel found. Please connect cable/antenna appears, check your TV connections, then press.
Program: TV System: VHF Low

01 Auto

The Program Sorting/Edit menu enables you to sort and edit the channels. a) If you wish to keep the channels in the current condition, press WEGA GATE to exit. b) Press V or v to select the program number with the channel you wish to change. The selected channel will appear on the screen. c) If you wish to store the channels in a different order: 1) Press b to enter sorting mode. 2) Press V or v to select the new program number position for your selected channel, then press B.
Program Sorting/Edit PROG Label Skip 01 Off 02 Off 03 Off 04 Off Edit: Sorting:

Select Confirm Exit

Program Sorting/Edit PROG Label Skip 01 Off 02 Off Off 04 Off Sorting mode

d) If you wish to edit the channels, press to change to edit mode. Press b until the mode that you wish to edit is highlighted: Label, Skip, (block symbol). Then press. 1) To label, press V or v to select the alphanumeric characters for the label. Then press. 2) To skip the program number, press V or v to select On. Then press. You can skip this program number when using PROG +/-. 3) To block unwanted program number, press V or v to select. Then press. e) Repeat step b) to d) if you wish to change other channels. Press WEGA GATE to go to the next menu.

Select

Confirm
Press B or b to adjust the bars on the top and bottom of the menu if they are. slanted, then press
Picture V-Position menu appears.
If the upper and lower bars are not equally positioned to the top and bottom of the screen, press V or v to. adjust them, then press If no adjustment is necessary, then press.
To prevent this Initial Setup menu from appearing again when you turn on the TV by pressing !, press V or v to select No,. then press To allow this menu to appear again, select Yes, then press.
Tip You can immediately go to the end of the Initial Setup menu by pressing WEGA GATE.
x TV front and rear panels

TV rear panel

(MONO)

L(MONO)

FM WEGA GATE

TV front panel

FM PROG

Button/Terminal 1 ! 2 1

4 PROG +/ +/ 6 t
Function Turn off or turn on the TV. Standby indicator. Wake Up indicator. Remote control sensor. Select program number. Adjust volume.
Select TV or video input. WEGA GATE menu operations Select and adjust items. 4,5 , , ,

Page 10 25

WEGA GATE 0 qa qs qd qf qg

FM i t2 MIC 1, MIC T t1

Confirm selected items. Display or cancel WEGA GATE menu. Listen to FM Radio. Headphone jack. Video input terminal 2. Microphone input terminal 1, 2. Antenna input terminal. Monitor output terminal. Component video input terminal. Video input terminal 1.
x Using the remote control and basic

functions

Button 1 ?/1 Description Turn off temporarily or turn on the TV. Display the TV program. Jump to last program number that has been watched for at least five seconds. Select program number. To select quickly, press and hold until the desired program number appears. Adjust volume. Change the picture size: On (16:9 wide mode), Off. Select surround mode options. Display on-screen information or Dynamic 5-Band Equalizer. Mute the sound. Select TV or video input. Input numbers. For program numbers 10 and above, enter the second digit within two seconds. Select sound mode options with a 5-Band Graphic Equalizer display. Select picture mode options. Confirm selected items. GATE Display or cancel the WEGA GATE menu. Page

01GB05AVD-SOEMRus.p65

15/8/07, 9:22 am
x Enjoying the Dynamic 5-Band Visualizer
The Dynamic 5-Band Visualizer enables you to visually enjoy the sound rhythm effect of the music and other sound from the TV. repeatedly until the Dynamic 5-Band Visualizer display appears on the Press screen.

On-screen information

Display Off

Visualizer

Dynamic 5-Band Visualizer display
Notes This feature is available for all TV channels, external inputs, FM Radio and Party Mode. To enjoy the visualization effect, you must set the volume level above 0 and make sure the TV is not in mute condition. Dynamic 5-Band Visualizer only represents the original sound and it is not affected by user adjustment (e.g., Sound Mode, Sound Adjustment). The visualization effect may vary depending on the original sound. You cannot change the position of the Dynamic 5-Band Visualizer display.
01GB05AVD-SOEMRus.p65 Black
x Enjoying the Party Mode
You can sing duet along with any music program of TV broadcast or with any audio/video equipment or create visual presentations (e.g., photos or video stories) with narration and favorite background music by using the Party Mode feature.

ON ON OFF OFF

Party Mode Setup MIC 1 Level MIC 2 Level Echo Level Vocal Reducer: Off Audio Input Fix: Off Reset Select End Confirm
Select the input connected to your audio/video equipment. Connect the microphone (not supplied) to the microphone input terminal and switch it on. You can begin singing or speaking from the microphone at the last TV volume setting. You can press A/B button on remote control to switch between left (L) or right (R) channel sound for VCD karaoke source only (either music or vocal) when video input is selected and Audio Input Fix is set to Off. Press WEGA GATE and select Party Mode. Select MIC 1 Level, MIC 2 Level or Echo Level, then press. Press V,v, B or b to adjust the microphone volume and echo level of the microphone sound, then press. If you want to reduce the vocal of the singer or speaker, select On from (effective for non-karaoke stereo source and Vocal Reducer and press when Audio Input Fix is Off only). Select Audio Input Fix and press , then press V or v to select the input connected to the audio equipment from which you want to hear the sound: Video 1, Video 2 or DVD. To revert to the original sound source, select Off, then press. Selecting Reset will set your TV to the factory settings (except for Audio Input Fix).
Notes Be sure to adjust the microphone and echo level to the minimum level before plugging in and disconnecting the microphone. For your own safety, do not use or plug in the microphone during lightning storms. Keep microphone away from the speakers and adjust its volume to avoid acoustic feedback (howling) and distortion. Microphone volume will be affected by TV volume. Vocal Reducer will be set to Off if users select L or R channel sound. Advanced Operations

x Listening to the FM Radio
You are able to listen to the FM radio stations using your TV. To access to FM Radio mode: Press WEGA GATE button and select FM Radio (see page 17). or Press FM button on the front panel (see page 8). To exit from FM Radio mode: Press WEGA GATE button, select the desired items: TV or External Inputs, then press. Select the desired TV channel or external inputs and press. or Press FM button on the front panel.
Listening to preset stations
Access to FM Radio mode. Press WEGA GATE button and select Settings. Preset the desired FM radio stations in FM Radio Setup from Channel Setup menu (see page 22). Exit from Channel Setup menu by pressing WEGA GATE button. The selected preset FM radio station number and label will appear on the screen. To select the desired preset FM radio station, press PROG +/.
Tip You can also use the 1-9 buttons on the remote control to directly select the desired preset FM radio station.

PROG +/

V, v, B, b
Listening to non-preset stations
Access to FM Radio mode. Press V or v to search for the desired FM radio station. The preset number and label will not be displayed. If the station has a weak signal, press B or b to fine tune the radio frequency manually.
Notes You can only operate V, v, B and b functions using the remote control buttons in FM Radio mode. The available radio frequency is only for temporary listening pleasure and cannot be stored in the memory. If the message Please setup FM Radio appears, display the Channel Setup menu and select FM Radio Setup to preset the desired FM radio stations (see page 22).
Note When a FM stereo program has static noise, press A/B until Mono appears. There will be no stereo effect, but the noise will be reduced.
x Enjoying stereo or bilingual programs
You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo systems by using the A/B button.
When receiving a NICAM program

Broadcasting

On-screen display (Selected sound)

NICAM (Stereo sound)

NICAM stereo

Mono (Regular sound)

NICAM bilingual
NICAM Main t NICAM Sub t Mono (Main sound) (Sub sound) (Regular sound)

NICAM monaural

NICAM Main (Main sound)
When receiving an A2 program

Broadcasting A2 stereo

Stereo (Stereo sound)

A2 bilingual

Main (Main sound)

Sub (Sub sound)

Note If the stereo sound is noisy when receiving a stereo program, select Mono. The sound becomes monaural, but the noise is reduced.

x Viewing Teletext

Some TV stations broadcast an information service called Teletext which allows you to receive various information, such as stock market reports and news. You can use the buttons on the remote to view Teletext.
To display a Teletext page on the TV picture Do this Press. Each time you press , the screen changes as follows: Teletext t Teletext and TV t TV. If there is no Teletext broadcast, 100 is displayed at the top left corner of the screen. Press. An overview of the Teletext contents, including page numbers, appears on the screen. Press the number buttons to enter the three-digit page number of the desired Teletext page. If you make a mistake, reenter the correct page number. To access the next or previous page, press or. Press to display the symbol at the top left corner of the screen. To resume normal Teletext viewing, press. Press. To conceal the information, press the button again. Press. Each time you press , the Teletext display changes as follows: Enlarge upper half t Enlarge lower half t Normal size.
check the contents of a Teletext service

select a Teletext page

RETURN WEGA WEGA GATE GATE
(red, green, yellow, blue)
hold (pause) a Teletext display
reveal concealed information (e.g., an answer to a quiz) enlarge the Teletext display
stand by for a Teletext (1) Enter the Teletext page number that page while watching you want to refer to, then press. a TV program (2) When the page number is displayed, press to show the text. select a FASTEXT menu or the colored boxes turn off Teletext Press (red, green, yellow and blue) that corresponds to the desired menu or page number. Press a.
Note The FASTEXT feature can be used only when the FASTEXT broadcast is available.
x Introducing the WEGA GATE navigator
WEGA GATE is a gateway that allows you access to preset TV channels, connected external inputs, FM Radio mode, Party Mode and Settings menu.
WEGA GATE TV External Inputs FM Radio Party Mode Settings Select Confirm
watch the preset TV channels (see page 6)

External Inputs

External Inputs FM Radio

Select End

Video 1 Video 2 DVD
select the inputs for the connected equipment (see page 25)

FM Radio

Preset 1:
---.-Please setup FM Radio
Select Preset 1-9 Search Fine

Party Mode

Party Mode Setup MIC 1 Level MIC 2 Level Echo Level Vocal Reducer: Off Audio Input Fix: Off Reset Select End Confirm Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Signal Level Indicator: On Select End Confirm
adjust your TV for Party Mode (see page 13)
listen to the FM Radio (see page 14) Settings
change the settings of your TV (see page 18)

How to use WEGA GATE

TV 05 Select
(1) Press WEGA GATE to display or cancel the WEGA GATE menu.
(3) Press V or v to select the desired item.
(2) Press (or b) to confirm your selection or go to the next level. Tip The WEGA GATE, operations above. and
(4) Press RETURN to move to the previous level.
buttons on the front panel can also be used for the Menu Adjustment

x Settings Adjustment

You are able to change the settings of your TV from Settings in WEGA GATE menu. Press WEGA GATE button to display WEGA GATE menu. Press V or v to select Settings and press. The following is an overview of the items that can be adjusted.
Picture Picture Mode: Vivid Picture Adjustment Color Temperature: Cool VM: High Intelligent Picture: On Signal Level Indicator: On Select End Confirm

Picture (see page 19)

Picture Mode: Vivid Standard Custom Picture Adjustment: Picture, Brightness, Color, Hue, Sharpness, Reset Color Temperature: Cool Neutral Warm VM: High Low Off Intelligent Picture: On Off Off Signal Level Indicator: On
Sound Sound Mode: Dynamic Sound Adjustment Balance Intelligent Volume: Off Surround: Off Select Confirm End

Sound (see page 21)

Sound Mode: Dynamic Standard Sound Adjustment: Adjust, Reset Balance Intelligent Volume: On Off Surround: On Simulated Off Custom
Channel Setup Auto Program Manual Program Program Sorting/Edit FM Radio Setup
Channel Setup (see page 22) Auto Program Manual Program Program: 00 - 99 TV System: B/G I D/K VHF Low/VHF High/UHF Fine: Auto Manual Off Signal Booster: Auto Program Sorting/Edit FM Radio Setup Setup (see page 24)
Setup Language: Picture Position Video Label Color System: Factory Settings

Adjusting the Sound Adjustment items under Custom mode
The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings of Custom mode in the menu.
Make sure that Adjust is selected, then press
Selecting Reset will set your TV to the factory settings. Press B or b to select the desired sound frequency, then press V or v to adjust the setting and press. The adjusted settings will be received when you select Custom.
Notes Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency will affect lower pitched sound. You may display the settings directly by using button on the remote control (see page 9).

01GB06ADJ-SOEMRus.p65

15/8/07, 9:23 am
x Changing the Channel Setup setting
The Channel Setup menu allows you to adjust settings below.
Press WEGA GATE and select Settings. Press V or v to select the Channel Setup icon ( ), then press.
Press V or v to select the desired item (e.g., Auto Program), then press
Select Auto Program Manual Program To preset channels automatically. manually preset desired channels and channels that cannot be preset automatically (see Presetting channels manually in page 23).
Program Sorting/Edit change the order in which the channels appear on the screen, label the program number, skip the program number and block unwanted programs (see step 3 of the section Initial Setup in page 6). FM Radio Setup* preset up to nine FM radio stations. You can manually preset each FM radio station that can be received in your area and then store the radio frequency of the desired FM radio stations. (1) Press V or v to select the desired FM radio station position, then press. (2) Press V or v to search the FM radio stations. Searching stops automatically when a station is tuned in. If the station has a weak signal, press B or b to fine tune the radio frequency manually, then press to store the FM radio station. (3) You may edit the FM radio station label. Press V or v to select alphanumeric characters for the label, then press. (4) Repeat steps (1) through (3) to preset other FM radio stations. * The FM Radio Setup feature is only available in FM Radio mode. To enable this feature, access to FM Radio mode by using WEGA GATE system (see page 17) or pressing the FM button on the front panel (see page 8), then preset your desired FM radio stations according to the steps mentioned above.

Notes If you preset a blocked program number, that program number will be unblocked automatically. If you sort a blocked program, that program will remain blocked. Menu Adjustment
01GB06ADJ-SOEMRus.p65 Black
Presetting channels manually
After selecting Manual Program, select the program number to which you want to preset a channel. (1) Make sure Program is selected, then press.
(2) Press V or v until the program number you want to preset appears on the menu, then press.
Manual Program Program : 01 D/K TV System: VHF Low Auto Fine: Auto Signal Booster: Confirm
Select the desired channel. (1) Make sure either VHF Low, VHF High or UHF is selected, then press. (2) Press V or v until the desired channels broadcast appears on the TV screen, then press.
If the sound of the desired channel is abnormal, select the appropriate TV system. (1) Press V or v to select TV System, then press.
(2) Press V or v until the sound becomes normal, then press
If you are not satisfied with the picture and sound quality, you may be able to improve them by using the Fine tuning feature. (1) Press V or v to select Fine, then press.
(2) Press V or v to select Manual, then press
(3) Press V,v,B or b until the picture and sound quality are optimal, then press The + or icon on the menu flashes while tuning.
If the TV signal is too strong (picture distorted; picture with lines; signal interference) or weak (snowy picture), you may be able to improve the picture quality by setting the Signal Booster feature. (1) Press V or v to select Signal Booster, then press.
(2) Press V or v to select either Off(for picture distorted; picture with lines; signal interference) or Auto (for snowy picture), then press.
x Changing the Setup setting
The Setup menu allows you to adjust settings below.
Press WEGA GATE and select Settings. Press V or v to select the Setup icon ( then press. ),
Setup Language: Picture Position Video Label Color System: Factory Settings Select Confirm English
Press V or v to select the desired item (e.g., Language), then press

Select Language To

change the menu language. Press V or v to select either English or (Russian), then press. adjust the picture position when it is not aligned with the TV screen. Press V or v to select Picture Rotation or Picture V-Position,. then press Press V, v, B or b to adjust the picture position, then press.

Picture Position

Video Label
label the connected equipment. (1) Select Video Input and press. Press V or v to select the input you want to label, then press. (2) Select Label and press , then press V or v to select the label options: Video 1/ Video 2/ DVD, VCR, SAT, Game or Edit*. * You may edit the video label to your favorite name. Press V or v to select alphanumeric characters for the label,. then press select the color system. Press V or v to select either Auto, PAL, SECAM,. Normally, set this to NTSC3.58 or NTSC4.43, then press Auto. reset your TV to factory settings. and press V or v to select Yes, then press Press To cancel, select No, then press.

Color System

Factory Settings
Note Color system is not selectable in FM Radio mode.

Additional Information

x Connecting optional components
Connecting to the video input terminal ( t )
TV front panel Audio/Video cable (not supplied)

Camcorder

Audio cable (not supplied) CD Player
Antenna cable (not supplied)
TV, CATV, Satellite or When there is no FM signal Antenna selector FM signal

TV signal

Antenna cable (not supplied) Audio/Video cable (not supplied)

DVD player

Note If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the program number 0 on the TV (see page 23). continue Additional Information
01GB07ADJ-SOEMRus.p65 Black
Connecting to the monitor output terminal ( T )
Audio/Video cable (not supplied)

Audio system

Connecting to the component video input terminal (
Component video cable (not supplied)
Audio cable (not supplied)

CR L R

Notes If your DVD player can output interlace and progressive mode signals, select the interlace output when connecting to (component video input) on your TV. Your TV can receive either 525i/60Hz or 625i/50Hz interlace signals. The component video terminals on your DVD player are sometimes labeled Y/CB/CR, Y/PB/ PR, Y/Cb/Cr or Y/B-Y/R-Y. If you select DVD on your TV screen, the signal from the T (monitor output) jacks will not be output properly. This does not indicate a malfunction.

x Troubleshooting

If you find any problem while viewing your TV, you can either use the Factory Settings function or check the Troubleshooting guide below. If the problem persists, contact your Sony dealer.
Factory Settings function
Press the WEGA GATE button. Choose Settings and go to Setup ( ) menu. From Setup menu, select Factory Settings. Then select Yes and press. Your TV will go blank for a few seconds, then the Initial Setup menu will appear. Your TV will be set to factory settings, but certain problems may be solved.

Symptom

Snowy picture, noisy sound
Solutions Check the antenna cable and connection on the TV, VCR and at the wall (see page 25). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and select Manual Program to preset the channel again (see page 23). Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 23). Try using an external booster. Turn off or disconnect the external booster if it is in use. Display the Channel Setup menu and set the Signal Booster to Off from Manual Program(see page 23). Display the Channel Setup menu and select the appropriate TV System from Manual Program (see page 23). Check the power cord, antenna and VCR connections (see page 25). Press ?/1 (power) to turn on the TV (see page 9). Press ! (main power) on the TV to turn off the TV for about five seconds, then turn it on again (see page 8). Press 2 + to increase the volume level (see page 9). Press to cancel the muting (see page 9). Display the WEGA GATE menu and set the Audio Input Fix to Off from Party Mode Setup (see page 13) Do not use a hair dryer or other equipment near the TV. Check the antenna setup. Contact a Sony dealer for advice. Use a highly directional antenna. Use the fine tuning (Fine) function (see page 23). Check the antenna setup. Contact a Sony dealer for advice. Turn off or disconnect the external booster if it is in use.

Distorted picture, noisy sound
Good picture, noisy sound No picture, no sound
Good picture, no sound No sound or inappropriate sound Dotted lines or stripes Double images or ghosts
continue Additional Information
01GB08ADV-SOEMRus.p65 Black

15/8/07, 9:24 am

No color
Solutions Display the Picture menu and select Custom from Picture Mode, then adjust the Color level from Picture Adjustment (see page 20). Display the Setup menu and check the Color System setting (usually set this to Auto) (see page 24). Check the antenna setup. Contact a Sony dealer for advice. Keep external speakers or other electrical equipment away from the TV. Display the Picture Position under Setup menu, then adjust Picture Rotation and Picture V-Position so that the picture is aligned to the TV screen (see page 24).

Picture slant

Abnormal color patches
Keep external speakers or other equipment away from the TV. Do not move the TV while the TV is turned on. Press ! (main power) on the TV to turn off the TV for about 15 minutes, then turn it on again to demagnetize the TV. Check the antenna cable and connection on the TV, VCR and at the wall (see page 25). Check the antenna setup. Contact a Sony dealer for advice.
TV cannot receive stereo broadcast sound or Stereo broadcast sound switches on and off or is distorted. Teletext display is incomplete (snowy picture or double images).
Check the antenna cable and connection on the TV, VCR and at the wall (see page 25). Check the antenna setup. Contact a Sony dealer for advice. Display the Channel Setup menu and set the Signal Booster to Auto from Manual Program (see page 23). Try using an external booster. Use the fine tuning (Fine) function (see page 23).
TV cannot receive FM radio station.
Connect a separate FM antenna and the TV channel source through an antenna selector (switch) to your TV (see page 25).
The 1 (standby) Count the number of times the 1 (standby) indicator flashes. indicator on your Press ! (main power) to turn off your TV. Contact your nearest Sony TV flashes red service center. several times after every three seconds. The TV screen sometimes goes blank for slightly longer than usual during channel change. TV cabinet creaks. A small boom sound is heard when the TV is turned on.
The Signal Booster is functioning to detect a weak signal. This does not indicate a malfunction.
Changes in room temperature sometimes make the TV cabinet expand or contract, causing a noise. This does not indicate a malfunction. The TVs demagnetizing function is working. This does not indicate a malfunction.

x Specifications

KV-SZ29M91K Power requirements Television system Color system Stereo/Bilingual system Teletext language Channel coverage B/G I D/K 220-240 V AC, 50/60 Hz B/G, I, D/K, M PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43 NICAM Stereo/Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G English, Russian VHF : E2 to E12 /UHF : E21 to E69 / CATV : S01 to S03, S1 to S41 UHF : B21 to B68 /CATV : S01 to S03, S1 to S41 VHF : C1 to C12, R1 to R12 / UHF : C13 to C57, R21 to R60 / CATV : S01 to S03, S1 to S41, Z1 to Z39 VHF : A2 to A13 /UHF : A14 to A79 / CATV : A-8 to A-2, A to W+4, W+6 to W+84 75-ohm external terminal 6W+6W Input: 2 Input: 3 Input: 1 Output: 1 Output: 1 Phono jacks; 1 Vp-p, 75 ohms Phono jacks; 500 mVrms Phono jacks; Y: 1 Vp-p, 75 ohms, sync negative CB: 0.7 Vp-p, 75 ohms CR: 0.7 Vp-p, 75 ohms Large jack Stereo minijack Note Power consumption (W) Indicated on the rear of the TV

M 8 (Antenna) Audio output (Speaker) Number of terminal (Video) (Audio) (Component Video)
MIC (Microphone) i (Headphone) FM Radio Tuning Range Intermediate Frequency Picture tube Tube size (cm)
Input: 2 Output: 1 87.5 - 108.0 MHz 10.7 MHz 29 in. 72 68
Measured diagonally Measured diagonally
Screen size (cm) Dimensions (w/h/d, mm) Mass (kg) Design and specifications are subject to change without notice.

2-887-146-12 (1)

.
02RU01COV-SOEMRus.p65 Black

15/8/07, 9:25 am

Sony KV-SZ29M91K Group A11 (RU)_2-887-146-12 (1)
. : 220-240 . , . () , . , .

- , .

. .

-. , - , ,.

, - . .

, , . , .

. , , .

. , , , .

. , .

, . .

. , . - (, , ) . .
, . . , , . , .
02RU02WAR-SOEMRus.p65 Black

.. 4 .. 5 ( a). 6

WEGA GATE.. .. .. . .. .. RU

.. 8 .. 9

B . 5- .. c pa (Party Mode). FM.. .. Teee.. 13 14

.. 25 . 27 .

. : Co A: 1-7-1 o, M-, To 108-0075,
02RU03TOC-SOEMRus.p65 Black

15/8/07, 9:32 am

, .

20 3,8

, .

(1) . (2) , .

(1) . (2) , , .

. .

02RU04INS-SOEMRus.p65 Black

15/8/07, 9:33 am

() .

( ) 8 ( ) .

FM 8 (. 25). (. 25).

, ! .

1 ( ) . .

, a (. 6).

x ( a)

a , . , , , .

V v , . .
V v a , . . , , /. , , . a. , .
/. . a) , WEGA GATE . b) V v , . . c) , : 1) b . 2) V v , B.

d) , . b : , , ( ).

1) V v - . . 2) , V v . . PROG +/-. 3) , V v . . e) b) - d), . WEGA GATE .
aae B b pepo e epxy y e, ec cy,. ae ae y . E , V v, , . E , .

!, V v , . , a ,.

a , WEGA GATE.

/ 1 ! 2 1

. . . 2 . 3 . 4 PROG +/ . +/ . 6 t WEGA GATE . 4,5 , , , . 6 WEGA GATE WEGA GATE . 7 FM. 8 FM . 9 i 2. 0 t2 1, 2. qa MIC 1, MIC 2 . qs 8 a /a. qd T a . qf t1 a 1. qg

. 10 25

1 ?/1 . . , . .

4 PROG +/ .

. :. (16:9 -. ), . . 5-. . . ( ). 10 . , 5- . .

qa qd t qf 0 9

WEGA GATE 6 .

7 WEGA WEGA GATE

GATE . .

qj V, v,

qk RETURN .
(. - 12 ). . , .