6. ELECTRICAL PARTS LIST.. 43

laser-tap

OPTICAL PICK-UP FLEXIBLE BOARD
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.

SECTION 1 SERVICE NOTE

1-1. TO PLACE THE SET INTO PLAYBACK MODE
The this set has no key control function and cannot be placed into the Playback mode alone. For key control, the this set is controlled through serial communication with a master unit (car audio player, TV tuner or source selector compatible with the Sony BUS system.) To service the this set, the set should be connected as given below:
Master unit (CDX-C880, C880R, etc.)

BUS CONTROL OUT

BUS CONTROL IN
1-2. HOW TO CHECK THE SERVO BOARD WAVEFORMS
1. Remove the panel (rear) assy, case (upper) and panel (front) assy. Then, remove the main board from the mechanism deck. (See page 8 of SECTION 3. DISASSEMBLY.) 2. Remove the chassis (OP) block from the mechanism deck. (See page 10 of SECTION 3. DISASSEMBLY.) 3. Short each bridge points BP1 and BP2 on the main board by solder bridge.
main board (conductor side)

BP1 BP2

4. Connect the power board with the main board by the main flexible board. Connect the main board with the servo board by the servo flexible board. 5. Connect to a master unit. With the master unit OFF, press the preset buttons 4 n 5 n 1 (2 seconds or more each) in this turn to enter the TEST mode. 6. Open the doors and insert a disc in the chassis (OP) assy. Use the SOURCE button on the master unit to select to MD to playback. 7. Check the waveforms at each point on the servo board. Note: After this check is completed, remove solder between shorted bridge points BP1 and BP2 and open these points.

SECTION 2 GENERAL

This section extracted from US, Canadian, E models instruction manual.

SECTION 3 DISASSEMBLY

Note : Follow the disassembly procedure in the numerical order given.

3-1. PANEL (REAR) ASSY

4 BVTT 2.6x6

6 panel (rear) assy

3 BVTT 2.6x6

2 PTT 2.6xCNcover

3-2. CASE (UPPER)

3 case (upper)

1 BVTT 2.6x6

2 BVTT 2.6x6

3-3. PANEL (FRONT) ASSY
3 panel (front) assy 1 claw

2 claw

4 CN620

3-4. MD BLOCK

4 tension spring (FL)
6 MD block 1 damper (798)

5 tension spring (FL)

2 damper (798)

3 tension spring (FL)

3-5. MAIN BOARD
3 escutcheon 6 chassis (front)
0 CNcollar (EHS) ! CN701 ! CN601 ! CNlead stopper 2 screws (M1.7) 1 cushion 4 screws (M1.7) ! CN700
9 CN602 ! special flat screws (1.7x3)
! MAIN board ! CNsheet (MAIN PC board) ! cushion (MAIN)

3-6. CHASSIS (OP) BLOCK

9 worm wheel (ELV2) 7 bearing (ELV) 8 bearing (ELV)

6 chassis (OP) block

5 bearing (ELV) 4 bearing (ELV)

3 chassis (bottom) assy

1 precision screws (P 1.7x1.8)
2 precision screws (P 1.7x1.8)

3-7. SERVO BOARD

3 screws (M1.7x2.2)

6 CN100

5 CN300

7 SERVO board

1 CN200

4 CN400

2 Unsolder the motor lead wires.

3-8. OPTICAL PICK-UP

1 screws (K1.7x3.5)

2 optical pick-up

3-9. NOTE ON ASSEMBLY FOR THE CHASSIS (OP) BLOCK
1 worm wheel (ELV2) 3 bearing (ELV) 4 bearing (ELV)

5 chassis (OP) block

2 Turn the three feed screw (ELV) assy fully in the direction of arrows A.

A A A 6 bearing (ELV)

8 chassis (bottom) assy 7 bearing (ELV)
9 precision screw (P1.7x1.8) ! gear (ELVC)
0 precision screws (P1.7x1.8)

! gear (ELVA2)

! polyethylene washer ! polyethylene washer

!Turn the three gear (ELVB) fully in the direction of arrows B.

SECTION 4 DIAGRAMS

4-1. IC PIN DESCRIPTIONS
IC100 CXA2523AR (RF AMP) Pin No. Pin Name 1 I J VC AF PD APC APCREF GND TEMPI TEMPR SWDT SCLK XLAT XSTBY FOCNT VREF EQADJ 3TADJ VCC WBLADJ TE CSLED SE ADFM ADIN ADAGC ADFG AUX FE ABCD BOTM PEAK RF RFAGC AGCI COMPO COMPP ADDC OPO OPN RFO MORFI MORFO I/O I I O I I O I I O I I I I I O I I I O I O O I I O O O O O O O I I O I I O I O I O Pin Description I-V converted RF signal input (I) from detector of optical pick-up. I-V converted RF signal input (J) from detector of optical pick-up. Center voltage (+1.65 V) generation output Signal input (A to F) from detector of optical pick-up. Quantity monitor input of light from laser diode of optical pick-up. Laser amplifier output to automatic power control circuit. Reference voltage input for laser power setting. GND Temperature sensor connecting pin (Not used in this set.) Reference voltage output for temperature sensor. (Not used in this set.) Write data signal input from System controller (IC600). Serial clock signal input from System controller (IC600). Serial latch signal input from System controller (IC600). Standby signal input (L : Standby) (Fixed at H in this set.) Center frequency control voltage input of internal circuit filter (BPF22, BPF3T and EQ). Reference voltage output (Not used in this set.) Center frequency setting input of internal circuit filter (EQ). Center frequency setting input of internal circuit filter (BPF3T). Power supply pin (+3.3 V) Center frequency setting input of internal circuit filter (BPF22). Tracking error signal output to CXD2652AR (IC200). Connecting pin for low pass filter condenser of sled error signal. Sled error signal output to CXD2652AR (IC200). FM signal output of ADIP. FM signal input of ADIP by AC combination. External condenser connecting pin for AGC of ADIP. ADIP double FM signal output (22.05 kHz 1 kHz) to CXD2652AR (IC200). Support signal (I3 signal/temperature signal) output (Not used in this set.) Focus error signal output to CXD2652AR (IC200). Quantity signal output of light to CXD2652AR (IC200). Bottom hold signal output of quantity signal (RF/ABCD) of light to CXD2652AR (IC200). Peak hold signal output of quantity signal (RF/ABCD) of light to CXD2652AR (IC200). Playback EFM RF signal output to CXD2652AR (IC200). External condenser connecting pin of AGC circuit for RF. RF signal input by AC combination. User comparator output pin (Not used in this set.) User comparator input pin (Fixed at L in this set.) External condenser connecting pin for low frequency interception of ADIP amplifier. External condenser connect pin for lower cut of ADIP amplifier. User operational amplifier inversion input pin (Fixed at L in this set.) RF signal output RF signal input of MO by AC combination. RF signal output of MO.

IC600 PD784216GC-027-8EU (SYSTEM CONTROLLER) Pin No. Pin Name I/O Pin Description 1 M1 O Elevator motor (M904) drive signal output 28, 36 37, 50 51, M1 M2 M2 MDMON LES SES HOME VDD X2 X1 VSS XT2 XT1 RESET BU IN BUS ON SQ SY STR SW CC XINT AVDD AVREF0 INIT TEMP EHS AVSS ERR PWM AVREF1 MD SI MD SO MD CKO UNISI UNISO UNI CKI LINKOFF D-BASS1, 2 MNTAGING AGCHK TFTON O O O O I I I I I I I O I O I I I I O O O O I O O O I O I O O I O O O O O O Elevator motor (M904) drive signal output Loading motor (M903) drive signal output Loading motor (M903) drive signal output Mechanism deck system power control output (H : Power ON) Loading end sensor detection switch (S902) input Store end sensor detection switch (S903) input Home position detection switch (S901) input (L : Home position) Power supply pin (+5 V) Main system clock connecting pin (14 MHz) Main system clock connecting pin (14 MHz) GND Sub system clock connecting pin (32.768 kHz) Sub system clock connecting pin (32.768 kHz) System reset input Backup OFF detection input (L : Backup OFF) BUS OFF detection of SONY BUS. (H : BUS OFF) Sub code Q sync input from CXD2652AR (IC200). STOP switch (S600) input Not used. Interruption status input from CXD2652AR (IC200). Not used. Power supply for A/D converter. (+5 V) Reference voltage for A/D converter. Initial input pin at reset. Thermistor connecting pin for temperature detection. Elevator height position detection input Connect to GND. Connect to GND. Analog GND Error data output (Not used in this set.) Not used. Reference voltage for D/A converter. Not used. Not used. Read data signal input from CXD2652AR (IC200). Write data signal output to CXA2523AR (IC100) and CXD2652AR (IC200). Serial clock signal output to CXA2523AR (IC100) and CXD2652AR (IC200). Not used. Not used. Serial data input for SONY BUS. Serial data output for SONY BUS. Serial clock input for SONY BUS. Link control signal output for SONY BUS. (H : Link OFF) Not used. Not used. Digital D-BASS select output 1, 2 (Not used in this set.) Not used. Monitor signal input from CXD2652AR (IC200). Not used. Not used. Not used.

Pin No. 99 100

Pin Name EE CS EE CKO EE SIO SENS LIMIT SW DOORSW MD LAT MD RST VSS MD ON EMPH O A ATT ILLON TSTSMD TSTCKO TSTSO TSTMOD VDD TSTOUTTSTINTEST/VPP DCS1 DCS2 DCS3 DCS4 DCS5 DCS6
I/O O O O I/O I I I O O O O I O I O O I O I I I I I I I
Pin Description Not used. Chip select output to EEPROM. (Not used in this set.) Serial clock output to EEPROM. (Not used in this set.) Data input from/output to EEPROM. (Not used in this set.) Internal status input from CXD2652AR (IC200). Optical pick-up innermost track limit position detection switch (S400) input Front door open detection switch (S620) input (L : Open complete) Serial latch signal output to CXA2523AR (IC100) and CXD2652AR (IC200). Reset signal output to CXD2652AR (IC200). GND Servo system power control output (H : Power ON) De-emphasis circuit control output (H : De-emphasis ON) Analog mute control input (H : Mute ON) Illumination lamp (PL620) light-up control output (H : Lamp light-up) Single mode setting pin (L : Single mode) Serial clock output to LED for TEST mode display. (Not used in this set.) Serial data output to LED for TEST mode display. (Not used in this set.) TEST mode setting pin (L : TEST mode) Power supply pin (+5 V) TEST key output pin of matrix. (Not used in this set.) TEST key input pin of matrix. (Not used in this set.) Fixed at L in this set. Disc with/without detection 1 switch (S611) input (H : with disc) Disc with/without detection 2 switch (S612) input (H : with disc) Disc with/without detection 3 switch (S613) input (H : with disc) Disc with/without detection 4 switch (S614) input (H : with disc) Disc with/without detection 5 switch (S615) input (H : with disc) Disc with/without detection 6 switch (S616) input (H : with disc)
4-2. CIRCUIT BOARDS LOCATION

SENSOR board

POWER board

MAIN board

LAMP board

SERVO board

4-3. BLOCK DIAGRAM
OPTICAL PICK-UP BLOCK (KMS-241A/J2N) DETECTOR 9 F 6 C F B A E C D 5 B J 2 J 4 A 7 D 8 E 1 I SWDT 16 SCLK 17 XLAT 18 RFO 46 AGCI 40 RF 38 TE 26 SE 28 ADFG 32 FE 34 AUTOMATIC POWER CONTROL QAPC BOTM 36 PEAK RFI 74 TE 73 SE 78 ADFG 65 FE 63 BOTM 62 PEAK XLAT 7 SCLK 6 SWDT 5 XRST 10 XINT 14 SRDT 8 SQSY 11 DOUT 22 DADT 24 XBCK PD PD ABCD ABCD LRCK 25 XLAT SCLK SWDT XRST XINT SRDT SQSY DOUT 5 DATA 6 BCK 4 LRCK MUTE DMI VOUTR VOUTL MNT0 MNT1 MNT2 MNT3 SENS S901 (HOME POSITION DET) 8 HOME RV901 ELEVATOR HEIGHT SENSOR S400 (LIMIT) 68 LIMIT SW S611-616 DISC WITH/ WITHOUT DET 95 DCSDCS6 S620 FRONT DOOR OPEN DET 69 DOORSW S902 LOADING END SENSOR DET IC201 RAM S903 STORE END SENSOR DET 7 SES IC700 ELEVATOR MOTOR DRIVE CONTROL DRIVER 9 M904 (ELEVATOR) M1 ILL ON LES PL620 (ILLUMINATION) +3.3V +3V REG. Q800, 801 LAMP DRIVE Q600, 601 IC970 REGULATOR CONTROL INPUT 4 OUT 1 VCC 2 MDMON 5 +9V REG. Q930, EMPH O R-CH SQSY DOUT 18 SQ SY A ATT 75 MUTING SWITCH Q500 IC930 LINE AMP 67 MNT0 MNT1 MNT2 MNT3 SENS 5 + R-CH MUTING CONTROL SWITCH Q932 MUTING Q920 AUDIO OUT MUTING Q910 CN902-1 L SRDT 40 MD SI BU IN 16 BATTERY DET Q940, 941 CN902-2 R 15 RSTB XINT 3 SWDT SCLK XLAT IC200 DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR IC500 D/A CONVERTER IC602 LEVEL SHIFT CC XINT IC902 IC902 DIGITAL OUT

4 IC100 RF AMP XRST XLAT SWDT SCLK IC600 SYSTEM CONTROL 71 MD RST 70 MD LAT 41 MD SO 42 MD CKO UNISO 46 UNISI 45 BUS ON SW UNI CKI RESET 15 IC601 RESET 8 IC900 BUS INTERFACE RESET SW 7 4
CN900 (BUS CONTROL OUT) SYS RST 1 BATT 4 BUS CLK BUS DATA BUS ON 6 3
PEAK HOLD Q200 IC202 LASER APC SWITCH 1 APC REF 2

75 AUX2 FS1 XTI

83 APC REF
IC603 LEVEL SHIFT CONTROL DRIVER 8 FOCUS 88 FFDR MNTFRDR MNTCONTROL DRIVER 29 TRACKING 86 TFDR MNTTRDR MNTSENS 4 MNT2 MNT3 SENS MNT12 MNT0
27 EHS Q602 B+ SWITCH B/U5V

+9V P/U5V

+6V REG. Q950 Q970 B+ SWITCH DRV5V +5V REG. Q972

M901 (SPINDLE)

CONTROL

DRIVER

93 SPRD

94 SPFD 91 SRDR

M902 (SLED)
92 SFDR AOAO17 OSCO DDXOE XCAS A09 XRAS XWE AADD4 3
IC300 SLED/SPINDLE MOTOR DRIVE, FOCUS/TRACKING COIL DRIVE

Signal Path : PB

X200 22.5792MHz 16 OSCI

STR SW 19 S600 STOP

XX600 14MHz X1 11

M903 (LOADING)

DE CAS A9 RAS WE
IC701 LOADING MOTOR DRIVE 3 M2

XTX601 32.768kHz

XT1 14
THIS NOTE IS COMMON FOR PRINDED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagrams All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. % : indicates tolerance. C : panel designation. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
4-4. PRINTED WIRING BOARDS SERVO SECTION
U : B+ Line. Power voltage is dc 14.4V and fed with regulated dc power supply from Master unit. Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : PB : Impossible to measure Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. E : PB for printed wiring boards X : parts extracted from the component side. Y : parts extracted from the conductor side. r : Through hole. b : Pattern from the side which enables seeing. (The other layers patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
Semiconductor Location Ref. No. D300 IC100 IC200 IC201 IC202 IC300 Q100 Q200 Location C-4 E-2 B-4 A-3 E-5 D-4 F-4 C-4

(Page 27)

4-5. SCHEMATIC DIAGRAM SERVO SECTION Refer to page 33 for Waveforms and page 35 for IC Block Diagrams.

(Page 23)

4-6. SCHEMATIC DIAGRAM MAIN SECTION Refer to page 34 for Waveforms and page 37 for IC Block Diagrams.

(Page 22)

(Page 32)
4-7. PRINTED WIRING BOARDS MAIN SECTION
Semiconductor Location Ref. No. D500 D501 D600 D601 D602 D800 D801 IC500 IC600 IC601 IC602 IC603 IC700 IC701 Q500 Q600 Q601 Q602 Q800 Q801 ( Location C-3 C-3 C-2 B-2 E-2 A-3 A-4 B-3 D-2 C-2 D-4 D-4 C-1 B-2 C-3 E-3 E-3 B-2 B-3 A-3

) : SIDE B

(Page 30)

(Page 20)

4-8. PRINTED WIRING BOARD POWER BOARD
Semiconductor Location Ref. No. D900 D901 D902 D903 D904 D905 D930 D940 D941 D950 D951 D952 D970 IC900 (IC902) IC930 IC970 Q910 Q920 Q930 Q931 Q932 Q940 Q941 Q950 Q970 Q972 ( Location B-2 B-2 A-2 A-2 A-2 A-2 D-4 E-6 E-7 E-5 E-4 E-3 D-9 B-3 E-1 C-4 E-7 C-2 C-2 D-5 D-3 B-3 E-6 E-6 E-3 E-4 D-8
4-9. SCHEMATIC DIAGRAM POWER SECTION Refer to page 37 for IC Block Diagrams.

(Page 24)

Waveforms
Servo Section 1 IC(A) PLAY MODE 200 mV/DIV, 10 sec/DIV 5 IC100 # (RF) PLAY MODE 500 mV/DIV, 1 sec/DIV 9 IC200 @ (XBCK) Main Section 1 IC600 ! (X2) 5 IC(XT1)

Approx. 150 mVp-p

Approx. 1.1 Vp-p

3.2 Vp-p

2.7 Vp-p

354 ns

2 IC(E) PLAY MODE 100 mV/DIV, 10 sec/DIV 6 IC100 #, IC200 ^ (FE) PLAY MODE 200 mV/DIV, 0.5 msec/DIV ! IC200 ! (OSCI)

71 ns 2 IC600 ! (XT1)

400 mVp-p

2.8 Vp-p

2.6 Vp-p
44.3 ns 3 IC(F) PLAY MODE 100 mV/DIV, 10 sec/DIV 7 IC100 @, IC200 & (TE) PLAY MODE 500 mV/DIV, 0.5 msec/DIV

30.4 s

3 IC(LRCK)

2.0 Vp-p

22.7 s
4 IC100 1, 2 (I, J) PLAY MODE 100 mV/DIV, 10 sec/DIV 8 IC200 @ (LRCK) 4 IC(BCK)

150 mVp-p

IC Block Diagrams Servo Section

IC100 CXA2523AR

RF AGC

45 + USROP

+ BPF3T

40 RF AGC

USRC DET EQ AUX SW
RFA2 I J OFST GRV GRVA HLPT 1 2

RFA3 3T

PEAK3T P-P WBL PEAK BOTTOM WBL PBH

TEMP 36 BOTM

GSW PD 10 + + APC 11 APCREF 12 13
35 ABCD 34 FE 33 AUX BPFC 32 ADFG
31 ADAGC BB + + 30 ADIN FEA
CC BPF22 + + DD WBL WBL ATA ADIP AGC

29 ADFM

1 PTGR 2 SEA

28 SE 27 CSLED

+ EBAL

EE' EFB ESW

+ + TESW

+ FBAL

WBL 3T EQ VI CONV 25 WBLADJ

AUXSW COMMAND

BGR VREF

SCRI - PARA DECODE

IC200 CXD2652AR
APCREF F0CNT TEST3 TEST2 TEST1 SRDR DVDD DCHG SPRD EFMO TRDR LDDR DVSS FRDR SFDR ADFG CKRF SPFD DTRF TFDR XLRF FFDR FGIN APC FS4

AUTO SEQUENCER

MNTMNTMNTMNTMONITOR CONTROL EACH BLOCK

SPINDLE SERVO

PWM GENERATOR
75 AUXTE 73 SE 72 AVSS 71 ADRB
ADIP DECODER SWDT 5 SCLK 6 XLAT 7 SRDT 8 SENS 9 XRST 10 SQSY 11 DQSY 12 RECP 13 SUBCODE PROCESSOR CPU I/F EACH BLOCK SERVO DSP A/D CONVERTER ANALOG MUX
70 ADRT 69 AVDD 68 ADIO 67 VC 66 AUXFE 64 ABCD 63 BOTM 62 PEAK 61 CLTV
60 FILO 59 FILI 58 PCO 57 PDO 56 AVSS
XINT 14 TX 15 OSCI 16 OSCO 17 XTSL 18 NC 19 DVSS 20 DIN 21 DOUT 22 CLOCK GENERATOR EACH BLOCK
SHOCK RESISTANT MEMORY CONTROLLER
EFM/ACIRC ENCODER/ DECODER

DIGITAL AUDIO I/F

SAMPLING RATE CONVERTER
55 RFI 54 BIAS 53 AVDD 52 ASYI 51 ASYO

ADDT 23 DADT 24 LRCK 25

ATRAC ENCODER/DECODER
ADDRESS/DATA BUS A00 - A11, D0 - D3

IC300 MPC17A38ZVMEL

PGND PGND PGND GND PS OE F/R4 PI4 RO3 VD RO4 RI3 FI3 VD FO3 FO4 VD VG

A01 A00

DC/DC CONVERTER VC CLOCK VC CLK DETECTOR VC

PRE-DRIVER VC

PRE-DRIVER

CONTROL VC

VC CLK GND

RI1 FI1 VD FO1 PGND PGND

VD RO2 PGND

FO2 VD FI2 RI2

Main Section IC500 PCM1718E-T1 IC700, 701 LB1638MTP-T1

GND N.C.

XTI 1 DGND 2 VDD 3 LRCIN 4 DIN 5 BCKIN 6 ZERO 7
CLK CONTROL INPUT INTERFACE MODE CONTROL DIGITAL FILTER
20 XTO 19 CLKO 14 MUTE DM1 DM0 RSTB FORMAT

CONTROL LOGIC

9 OUTVS 7 OUT2

VCC 3 INGND 5

NOISE SHAPER 5 LEVEL DAC LOWPASS FILTER 5 LEVEL DAC LOWPASS FILTER CMOS AMP 13 D/C L 12 VOUTL 11 VCC

6 N.C.

D/C R 8 VOUTR 9 AGND 10

CMOS AMP

Power Section IC900 BA8272F-E2
DATA OUT LINK OFF CLK OUT DATA IN BUS ON

IC970 TL5001CPS-E20

FEED BACK

RESET SWITCH

U.V.L.O REFERENCE VOLTAGE + OSC + S.C.P. COMPARATOR 1 SWITCH 'ON' AT 'H' DEAD-TIME COMPARATOR +

BUS CLK

BUS ON OUT

BUS DATA

BUS RESET

BUS ON IN

ERROR AMP
+ PWM COMPARATOR + S.C.P. LATCH

S.C.P. COMPARATOR 8

Description HOLDER(OPGUIDEB) GUIDE(OPB) SCREW(EL V)ASSY ,FEED EHSFLEXIBLEBOARD SLEEVE(EL V2) SPRING(EL V), COMPRESSION PLA TE (B), EL V LIMITER CHASSIS(OP)ASSY PLA TE (A), EL V LIMITER SPRING(EL V2), COMPRESSION WHEEL(SL),WORM WASHER (0.8-2.5) SCREW(K1.7X3.5) RET AINER(SP) HOLDER(SLB) DETENT ,SL
Ref. No. ! 221 * 224 * M901 M902 RV901 S901
Part No. X-3371-213-1 X-3371-214-1 3-930-331-01 3-020-346-01 8-583-037-02 A-3294-337-A 3-932-755-01 3-703-816-32 3-018-070-01 3-930-333-01 A-3291-507-A A-3291-508-A 1-223-817-11 1-570-771-21
Description HOLDER(SLA)ASSY SCREW(SL)ASSY ,FEED GUIDE(OP A) SPRING(SLOUT2),FEED PICK-UP ,OPTICALKMS-241A/J2N SERVOBOARD,COMPLETE SCREW (M1.7X2.2) SCREW(M1.4X1.6),SPECIALHEAD SHEET(TT) SLEEVE(EL V)
MOTORBLOCKASSY ,SP(SPINDLE) MOTORBLOCKASSY ,SL(SLED) RES, VAR, SLIDE 10K (ELEV ATOR HEIGHT SENSOR) SWITCH(HOMEPOSITIONDET)
SECTION 6 ELECTRICAL PARTS LIST
NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable Abbreviation G : German model Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : , for example: uA. : A. uPA. : PA. uPB. : PB. uPC. : PC. uPD. : PD. CAPACITORS uF : F COILS uH : H
The components identified by mark ! dotted line with mark. or ! critical for safety. are Replace only with part number specified. Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. When indicating parts by reference number, please include the board.

Ref. No. *

Part No. 1-672-198-11
Description LAMPBOARD ************ <CAP ACIT OR>
Ref. No. C604 C605 C606 C607 C608
Part No. 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-104-852-11
Description CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP TANT AL. CHIP <CONNECTOR> 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 22uF 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 20%

3-031-503-01

10% 20% 5% 10%
Ref. No. C973 C974 C975 C976 C977 C978 C980 C981 C983 C984 Part No. 1-164-004-11 1-164-004-11 1-126-204-11 1-128-590-11 1-128-590-11 1-128-590-11 1-128-590-11 1-127-485-00 1-164-004-11 1-164-004-11 Description CERAMICCHIP CERAMICCHIP ELECTCHIP ELECTCHIP ELECTCHIP ELECTCHIP ELECTCHIP ELECT CERAMICCHIP CERAMICCHIP <CONNECTOR> CN900 * CN901 1-580-907-12 1-573-939-11 PLUG,CONNECTOR(BUSCONTROLOUT) CONNECTOR,FFC/FPC(ZIF)30P <JACK> CN902 1-580-441-11 JACK,PIN2P(AUDIOOUT) <DIODE> D900 D901 D902 D903 D904 D905 D930 D940 D941 D950 D951 D952 D970 8-719-421-27 8-719-057-80 8-719-421-27 8-719-057-80 8-719-421-27 8-719-057-80 8-719-422-97 8-719-977-12 8-719-988-61 8-719-988-61 8-719-422-62 8-719-041-79 8-719-210-43 DIODE MA728 DIODE MA8160-M-TX DIODE MA728 DIODE MA8160-M-TX DIODE MA728 DIODE MA8160-M-TX DIODE MA8091-M DIODE DTZ6.8B DIODE 1SS355TE-17 DIODE 1SS355TE-17 DIODE MA8062-L-TX DIODE MA721W A-TX DIODE EC10QS-06 <JUMPERRESISTOR> FB903 1-216-295-00 SHOR T < IC > IC900 IC902 IC930 IC970 8-759-444-86 8-749-923-53 8-759-711-82 8-759-983-96 IC BA8272F-E2 IC TOTX193 (DIGIT AL OUT) IC NJM4580E IC TL5001CPS <COIL> L970 L971 L972 1-409-640-21 1-403-584-11 1-409-640-21 INDUCTOR INDUCTOR INDUCTOR <FIL TER> NF900 1-239-466-21 FIL TER, EMI <FUSE> PC1 1-533-351-11 FUSE, CHIP (2A/125V) 10uH 33uH 10uH 0 R942 R943 R950 R951 R970 R971 R972 R973 R974 R975 R976 R977 R978 R979 R980 R981 1-216-109-00 1-216-089-00 1-216-049-11 1-216-085-00 1-216-214-00 1-216-206-00 1-216-206-00 1-216-061-00 1-216-081-00 1-216-077-00 1-216-174-00 1-216-198-00 1-216-198-00 1-216-663-11 1-216-649-11 1-216-158-00 MET ALCHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP MET ALCHIP MET ALCHIP MET ALCHIP RES,CHIP RES,CHIP RES,CHIP MET ALCHIP MET ALCHIP RES,CHIP <SWITCH> SW1 1-572-552-11 SWITCH, SLIDE(ANALOG/DIGIT AL) ************************************************************* 330K 47K 1 K 33K 4.7K 2.2K 2.2K 3.3K 22K 15K K 1 K 3.3K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/8W R913 R914 R915 R920 R921 R922 R923 R924 R925 R930 R931 R932 R933 R940 R941 1-216-081-00 1-216-033-00 1-216-097-00 1-216-079-00 1-216-097-00 1-216-081-00 1-216-081-00 1-216-033-00 1-216-097-00 1-216-049-11 1-216-057-00 1-216-057-00 1-216-009-00 1-216-097-00 1-216-093-00 MET ALCHIP MET ALCHIP RES,CHIP MET ALCHIP RES,CHIP MET ALCHIP MET ALCHIP MET ALCHIP RES,CHIP RES,CHIP MET ALCHIP MET ALCHIP RES,CHIP RES,CHIP RES,CHIP 22K 220 100K 18K 100K 22K 22K 220 100K 1 K 2.2K 2.2K 22 100K 68K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W R900 R901 R910 R911 R912 1-216-089-00 1-216-071-00 1-216-079-00 1-216-097-00 1-216-081-00 0.1uF 0.1uF 47uF 100uF 100uF 100uF 100uF 33uF 0.1uF 0.1uF 10% 10% 20% 20% 20% 20% 20% 20% 10% 10% Remark 25V 25V 16V 6.3V 6.3V 6.3V 6.3V 6.3V 25V 25V Ref. No. Part No. Description <TRANSISTOR> Q910 Q920 Q930 Q931 Q932 Q940 Q941 Q950 Q970 Q972 8-729-920-21 8-729-920-21 8-729-424-59 8-729-920-85 8-729-424-12 8-729-230-49 8-729-901-06 8-729-920-85 8-729-106-60 8-729-822-84 TRANSISTOR DTC314TKH04 TRANSISTOR DTC314TKH04 TRANSISTOR UN2212 TRANSISTOR 2SD1664-QR TRANSISTOR UN2112 TRANSISTOR 2SC2712-YG TRANSIST OR DT A144EK TRANSISTOR 2SD1664-QR TRANSISTOR 2SB1115A TRANSIST OR 2SB1202F AST <RESISTOR> RES,CHIP MET ALCHIP MET ALCHIP RES,CHIP MET ALCHIP 47K 8.2K 18K 100K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Remark

SENSOR

Ref. No. Part No.
Description Remark Ref. No. Part No. Description <CONNECTOR> CN100 CN200 * CN300 CN400 1-573-929-11 1-573-370-21 1-770-619-11 1-573-346-21 CONNECTOR,FFC/FPC(ZIF)20P CONNECTOR,FFC/FPC30P PIN,CONNECTOR2P CONNECTOR,FFC/FPC6P <DIODE> D300 15uF 10uF 10uF 0.001uF 0.0068uF 0.022uF 0.1uF 0.068uF 0.0047uF 1uF 0.1uF 0.022uF 0.01uF 0.1uF 15uF 22PF 22PF 150PF 0.01uF 0.47uF 0.1uF 100PF 0.0047uF 0.47uF 0.015uF 0.1uF 1uF 0.1uF 0.1uF 0.1uF 100PF 0.1uF 0.01uF 0.01uF 22uF 0.1uF 1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 20% 20% 20% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 10% 20% 5% 5% 5% 10% 10% 10% 5% 10% 10% 5% 10% 10% 10% 10% 10% 5% 10% 10% 10% 20% 10% 10% 10% 10% 10% 10% 10% 10% 6.3V 4V 4V 50V 25V 25V 16V 16V 50V 10V 16V 25V 25V 16V 6.3V 50V 50V 50V 25V 16V 16V 50V 50V 16V 50V 16V 10V 16V 16V 16V 50V 16V 25V 25V 10V 16V 16V 16V 16V 16V 16V 16V 16V 8-719-988-61 DIODE 1SS355TE-17 <FERRITEBEAD> FB200 1-414-594-11 INDUCTOR,FERRITEBEAD < IC > IC100 IC200 IC201 IC202 IC300 8-752-080-95 8-752-384-47 8-759-498-44 8-759-058-62 8-759-442-80 IC CXA2523AR IC CXD2652AR IC MSM51V4400-70TS-K IC TC7S08FU(TE85R) IC MPC17A38ZVMEL <COIL> L100 L200 L300 1-412-058-11 1-412-058-11 1-412-034-11 INDUCTORCHIP INDUCTORCHIP INDUCTORCHIP <TRANSISTOR> Q100 Q200 8-729-216-22 8-729-230-49 TRANSISTOR 2SA1162-G TRANSISTOR 2SC2712-YG <RESISTOR> 10uH 10uH 330uH Remark
SENSORBOARD,COMPLETE ************************ WhenreplacinganypartsintheSENSORboard, thewholemountedboardshouldbereplaced. ************************************************************* * A-3294-337-A SERVOBOARD,COMPLETE *********************** <CAP ACIT OR> C100 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C200 C202 C203 C204 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C217 C218 C219 C220 C221 C300 C301 C302 C303 C304 C305 C306 C400 C401 1-107-685-11 1-135-201-11 1-135-201-11 1-162-964-11 1-162-969-11 1-164-227-11 1-107-826-11 1-110-563-11 1-162-968-11 1-109-982-11 1-107-826-11 1-164-227-11 1-162-970-11 1-107-826-11 1-107-685-11 1-162-919-11 1-162-919-11 1-164-217-11 1-162-970-11 1-107-823-11 1-107-826-11 1-162-927-11 1-162-968-11 1-107-823-11 1-163-023-00 1-107-826-11 1-109-982-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-927-11 1-107-826-11 1-162-970-11 1-162-970-11 1-104-852-11 1-107-826-11 1-107-682-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 TANT AL. CHIP TANT ALUMCHIP TANT ALUMCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP TANT AL. CHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP TANT AL. CHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP CERAMICCHIP

#6 7-627-552-18 SCREW ,PRECISION+P1.7X1.6 #7 7-627-852-58 SCREW ,PRECISION+P1.7X5 TYPE3 ************************************************************* PAR TSFORINST ALLA TIONANDCONNECTIONS *************************************** 257 3-930-163-21 X-3371-178-1 3-930-166-01 7-682-961-01 4-304-511-00 1-590-519-21 1-777-284-11 BASE(FITTING) BRACKETASSY CUSHION(FITTING) SCREW+PSW4X8 NUT(M5),FLANGE CORD(WITHCONNECTOR)(BUSCABLE)(5.5m) CORD,CONNECTION(RCAPINCORD)(5.5m)
S901 1-570-771-21 SWITCH(HOMEPOSITIONDET) S902 1-570-771-11 SWITCH(LOADINGENDSENSORDET) S903 1-570-771-21 SWITCH(STOREENDSENSORDET) ************************************************************* ACCESSORIES&P ACKINGMA TERIALS ******************************** MANU AL, INSTR UCTION, INST ALL(ENGLISH, FRENCH,SP ANISH,CHINESE) (US,Canadian,E) 3-865-928-11 MANU AL, INSTR UCTION(ENGLISH,SP ANISH, SWEDISH,POR TUGUESE)(AEP ,UK) 3-865-928-21 MANUAL,INSTRUCTION(FRENCH,GERMAN, DUTCH,IT ALIAN)(AEP ,UK) 3-865-928-31 MANUAL,INSTRUCTION(GERMAN,RUSSIAN)(G) ************************************************************* 3-865-667-11
The components identified by mark ! dotted line with mark. or ! critical for safety. are Replace only with part number specified.
Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

Sony Corporation

9-926-423-11
Personal & Mobile Communication Company
99A0478-1 Printed in Japan C1999. 1 Published by Quality Assurance Dept.