E N G L I S H

General advice
Dear client, many thanks for having chosen an Audiotechnik Dietz product. You have made a magnificent choice. While developing this product, your personal safety combined with the best operating service, modern design and an up-to-date production technique was especially taken into account. Unfortunately, despite the utmost care injuries and/or damages might occur due to improper installation and/or use. Please read the attached instruction manual completely with great care and keep it! This product meets the actual European and national directions. The conformity was proved, the respective documents and explanations are stored with the manufacturer. All articles of our production line pass through a 100 % check - for your safety and security. We reserve the right to carry out technical changes which serve the improvement at any time. According to each article and purpose, it is sometimes necessary to check each countrys legal regulations before installing and starting the unit. In case of guarantee claims, the device has to be sent back to the seller in the original packaging with the attached bill of purchase and detailed defect's description. Please pay attention to the manufacturer's return requirements (RMA). The legal warranty directions are valid. The guarantee claim as well as the operating permission becomes invalid due to: a) unauthorized changes to the device or accessories which have not been approved or carried out by the manufacturer or its partners b) opening the device's frame c) device's repairs carried out by one's own d) improper use / operation e) brute force to the device (drop, wilful damage, accident etc.) During installation, please pay attention to all safety relevant and legal directions. The device has only to be installed by trained personnel or similarly qualified people.

Scope of delivery

- 1 pc. instruction manual - 1 pc. interface - 1 pc. Cable kit (only 61007)
General safety instructions
WARNINGS Installation requires special knowledge. Do not install the unit yourself. For safe and reliable installation, consult a dealer having special knowledge. Installation may only be done during idle status. Disconnect the battery from the cars electrical system, for example. Thereby, please pay attention to the cars manufacturer-requirements. Never use bolts or nuts from the cars safety devices for installation. If bolts or nuts from the steering wheel, brakes or other safety devices are used for installation of the unit, it may cause an accident. Use the unit with a DC 12V negative ground car. This unit cannot be used in large trucks which use a DC 24V battery. If it is used with a DC 24V battery, it may cause a fire or accident. Avoid installing the unit in following places: - Where it would hinder your safe driving. - Where it could damage the cars fittings.

CAUTION Since there may be legal regulations defining the permissible installation locations for this unit, be sure to install it in a location complying with any such laws.
The references in this chapter apply to most of our products, but not to all. If you have further questions, please contact your local dealer. Do not hit this product. Avoid any damage. Warning! Risk of electric shock! Never remove the cover. There are no user-serviceable parts inside. Refer servicing to qualified personal.
Warning! Risk of fire or electric shock! Do not use this product near water (for example bathtub, washbowl, etc.) or in wet basements (swimming pool). To reduce the risk of casualties, never expose the unit any moisture. Never put a wet object (like a flower pot) on the unit. Warning! Risk of electric shock! To protect the unit against damage, unplug the power cable and the antennas of the unit if a thunder is present. Warning! Risk of fire or electric shock! Do not overload wall outlets and extension cords.
Warning! Risk of fire or electric shock! Never insert objects of any kind into this product through openings. They can cause short circuits, which could result in fire or electric shock.
Warning! Risk of fire or electric shock! When the cable or plug of this product is broken, please pull out the plug and refer servicing to qualified personal. Warning! Risk of fire or electric shock! Dont put anything on the power cable! This can damage the cable.
If smoking, abnormal sound or peculiar smell happens, disconnect the power source. Stop using this unit.
Protect the unit against any kind of heat. Never mount it close to heat sources. This product should never be placed near or over a radiator or under the sun.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided.
Unplug the power cable if: a. the unit is unused for a long time b. you want to clean the unit. (Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning). c. the unit doesnt work, even after you have consulted the troubleshooting chapter (in this case, please contact a service-partner). Do not place this unit on extension dust. If the temperature is highly damp, agglomerate dust will damage the unit.
Do not block Slots and openings in the cabinet or in the back or bottom.
The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surfaces.
Do not place this product on an unstable cart, stand, table, etc. The product may fall, causing serious injury and serious damage to the product.
Repairs should only be made by our service-partners. Never do a repair self, otherwise the claim of guarantee expires. Unplug the unit from the power source if you have to replace a burned fuse. Only use fuses of the same kind and size. Wrong fuses can damage the unit!

References of legal regulations for operation
Only use this unit in the intended domain. If you use it in a foreign domain, if the unit is not installed properly, or if the unit will be reconstructed, the guarantee will expire.
Following types of cars are supported
ALFA ROMEO 147*, BRERA, 159 CITRON C3, C4, C5 10/04 on, C8 with MOST CITRON Jumper 10/06 on CITRON Jumpy 2008 on CITRON Nemo*** FIAT Panda 2006 on, Ducato 2006 on FIAT Stilo*, Grande Punto 2006 on, FIAT 500, Scudo 2007 on, Bravo 2007 on, Croma 2005 on FORD Focus**, Focus C-MAX**, Mondeo (B4Y/B5Y/BWY) 07/03 - 04/07**, Mondeo* (BA7) 04/07 on, S-MAX, Galaxy 06/06, Kuga*, Fiesta 10/05 09/08, Transit* (2009 on); with MOST LANCIA Ypsilon 11/03~ LAND ROVER Discovery 3, Range Rover 05~, Range Rover Sport LEXUS GS Serie: GS300, GS430 MAZDA 2, 5, 6 MERCEDES Actros 1847, 1850 PEUGEOT Boxer 2006 on PEUGEOT 207, 307, 308, 407, Expert* with MOST SAAB 9-3, 9-5 SAAB 9-3 with MOST VOLVO FH12, FH16 VOLVO S60, V70, XC70 VOLVO V70 Model year 2008 on VOLVO XC90

Cable kit:

61038* 61019* 61024* 61024 61025* 61024* 61019* 61024* 61038**** 61023
* = no / partly support for steering wheel for more detail information have a look at the car cable kit. ** = speed pulse output only *** = no support for illumination **** = activation of OEM sound system X = suitable, no cable kit needed 61XXX = suitable with this cable kit

Operating mode 61007

The assembly mentioned above is an interface able to read out following signals from the CAN protocol of a car: Speed impulse
ATTENTION! Connection only to +12V!!! Pin assignment
I/O input input input output input marking CAN high CAN low ground

Speed impulse

voltage +12 V permanent, terminal 30
cable yellow blue black orange red
Tap off locations for CAN high and CAN low are described in the appendix from page 18.

Operating mode 61009

The assembly mentioned above is an interface able to read out following signals from the CAN protocol of a car. Decryption as follows (depending on cars configuration): ignition (terminal 15, 1A maximum load!) illumination (terminal. 58, 1A maximum load!) speed impulse: square wave signal, 0,64 Hz per km/h reverse gear (depends on cars configuration, 100mA maximum load!) steering wheel remote control (if exists) for afterwards mentioned BECKER units
For more specific information about features please refer to the installation manual from the cable kit of the concerning car. For installation of stand-alone navigation systems with use of 61009, where the originally built in radio remains in the car, we recommend using the cable kit 61019. No steering wheel controls are supported with this cable kit. Tap off locations of CAN high and CAN low for installation of the cable kits 61019 and 61023 are described in the appendix from page 18. Steering wheel remote control will only be adapted when it was originally built in and communicates via CAN data bus with the OEM radio.

Compatible units for adaptation of the steering wheel controls with 61009: BECKER: Cascade 7944, Traffic Pro 472X, 794X, Traffic Pro high speed 782X, Online Pro 7800, DTM 780X, DTM high speed 791X, Mexico Pro 793X, Monza mp3 788X, Indianapolis 792X JVC: KD-NX1R, KD-NX10 SONY: MEX-100NV
ATTENTION: The steering wheel remote control will only work when ignition is on. If the Interface is installed, you can only connect the current CD-Changer which is announced to fit with your head unit! You can not connect the BECKER Remote kit for iPod and the steering wheel control in the same time. It is possible to connect only one of both.

Operating mode 61303

The assembly mentioned above is an interface able to read out following signals from the CAN protocol of a car. Decryption as follows (depending on cars configuration): ignition (terminal 15, 1A maximum load!) illumination (terminal. 58, 1A maximum load!) speed impulse: square wave signal, 0,64 Hz per km/h reverse gear (depends on cars configuration, 100mA maximum load!) telephone mute (depends on cars configuration) steering wheel remote control (if exists) for afterwards mentioned units from different manufacturers
For more specific information about features, please refer to the installation manual from the cable kit of the concerning car. Tap off locations of CAN high and CAN low for installation of the cable kit 61323 are described in the appendix from page 18. Steering wheel remote control will only be adapted when it was originally built in and communicates via CAN data bus with the OEM radio. Compatible units for adaptation of the steering wheel controls with via radio specific adapter: 61401: PANASONIC: CQ-C8301 and identical 61402: BECKER: Cascade 7944, Traffic Pro 472X, 794X, Traffic Pro high speed 782X, Online Pro 7800, DTM 780X, DTM high speed 791X, Mexico Pro 793X, Monza mp3 788X, Indianapolis 792X KD-NX1R, KD-NX10 MEX-100NV all with connection for remote control model year 03 on KDCM4524 and identical CDE-9821R and identical DEH 1600R and identical DXZ848RMC and identical
61404: BLAUPUNKT: TravelPilot DX-R 52, Virginia DJ 50 and identical
ATTENTION: The steering wheel remote control will only work when ignition is on. If the Interface is installed with Becker head units, you can only connect the current CD-Changer which is announced to fit with your head unit! You can not connect the BECKER Remote kit for iPod and the steering wheel control in the same time. It is possible to connect only one of both.

Service notes

This unit does not need any servicing. Do not open the housing. There are no user-serviceable parts inside. Wipe gently with a dry cloth over the surface to clean the unit. If there is more tough dirt, first use a light wet cloth and then uses a dry one. Never use corrosive cleaners to clean the unit.

Technical data

Software: Power supply: Working Voltage: Quiescent current: 4.0.9 (61007), 3.0.8 (61009) 12 V DC 10,0 14,6 V DC 2 mA
Power consumption: 0,58 W Temperature range: -40 - +85 C Weight: Dimensions: 0,068 kg 70 x 50 x 30 mm
Software: Power supply: Working Voltage: Quiescent current: 2.5.V DC 10,0 14,6 V DC 40 mA
Power consumption: 0,58 W Temperature range: -40 - +85 C Weight: Dimensions: 0,110 kg 80 x 60 x 30 mm
This unit is only for automotive use and has therefore a lifetime of max. 10 years.
Abgriffpunkte des CAN Bus fr die Interfaces 61007, sowie die Kabelstze mit losen Enden 61019, 61023, 61323 Tap off locations of the CAN Bus for interfaces 61007, as well as for cable kits with loose ends 61019, 61023, 61323
ALFA ROMEO / FIAT / LANCIA: - Abgriff am Strom ISO Stecker im Radioschacht: CAN low: Pin 3 wei / rosa, CAN high: Pin 1 schwarz / rosa. - Tap off at the power ISO connector in the radio slot: CAN low: pin 3 white / pink, CAN high: pin 1 black / pink. ______________________________________________________________________________________
CITRON C3, C4, C4 Picasso, C5, Jumpy: - Abgriff im Radioschacht am MOST Stecker, CAN low: Pin 13 grau oder blau, CAN high: Pin 10 wei. - Tap off in the radio slot at the MOST connector, CAN low: pin 13 grey or blue, CAN high: pin 10 white.
CITRON Jumper ab 10/06: - Abgriff im Sicherungskasten am blauer 52 poliger Stecker, CAN low: Pin 48 braun / blau CAN high: Pin 49 grn / blau. - Tap off in fuse box at the blue 52 pin connector, CAN low: pin 48 brown / blue CAN high: pin 49 green / blue.
CITRON Nemo: Abgriff an OBD Stecker im Fahrerfuraum links am Sicherungskasten: CAN high: Pin 6 CAN low: Pin 14 Tap off on the OBD plug in the drivers food space left of the fuse box: CAN high: Pin 6 CAN low: Pin 14 PIN 16 PIN 9 PIN 1

FORD: - Fiesta, Focus, Focus C-MAX, S-MAX, Mondeo, Galaxy, Kuga. Abgriff im Radioschacht am MOST Stecker, CAN low: Pin 10 blau, CAN high: Pin 9 grau. - Fiesta, Focus, Focus C-MAX, S-MAX, Mondeo, Galaxy, Kuga. To tap off in the radio slot at the MOST connector: CAN low: pin 10 blue, CAN high: pin 9 grey. ______________________________________________________________________________________ FIAT: - Stilo, Grande Punto, 500, Bravo, Panda, Croma. Abgriff im Radioschacht am ISO Stecker: CAN low: Pin 3, CAN high: Pin 1. - Stilo, Grande Punto, 500, Bravo, Panda, Croma. To tap off in the radio slot at the ISO connector: CAN low: pin 3, CAN high: pin 1. - Ducato Abgriff hinter Sicherungskasten: CAN low: Pin 5 rosa/wei, CAN high: Pin 6 rosa/schwarz. - Ducato Tap off behind fuse box: CAN low: pin 5 pink/white, CAN high: pin 6 pink/black. - Scudo siehe Peugeot / see Peugeot ______________________________________________________________________________________ Land Rover: - Discovery 3, Range Rover 2005~, Range Rover Sport: Abgriff am Diagnosestecker: CAN low: gelb/schwarz Pin14, CAN high: gelb/braun Ppin 6. - Discovery 3, Range Rover 2005~, Range Rover Sport: Tap off at the diagnostic connector: CAN low: yellow/black pin14, CAN high: yellow/brown pin 6. ______________________________________________________________________________________
MAZDA: - 2: Abgriff hinterm Kombiinstrument: CAN low: wei, CAN high: rot. - 2: Tap off behind the dashboard: CAN low: wei, CAN high: red. - 5: Abgriff im Radioschacht: CAN low: grau / silber, CAN high: blau / wei. - 5: Tap off behind the dashboard: CAN low: grey / silver, CAN high: blue / white. - 6: Abgriff hinterm Kombiinstrument: CAN low: blau, CAN high: rot. - 6: Tap off in the radio slot: CAN low: blue, CAN high: red. ______________________________________________________________________________________ MERCEDES: - Actros 1846, 1850 ACHTUNG! Nur an +12V anschlieen!!! Abgriff im Radioschacht am 10 poligen ISO Stecker CAN low: Pin 2 gelb / schwarz, CAN high: Pin 1 blau - Actros 1846, 1850 ATTENTION! Connection only to +12V!!! To tap off in the radio slot at the 10 pin ISO connector CAN low: pin 2 yellow / black, CAN high: pin 1 blue. ______________________________________________________________________________________

PEUGEOT 207, 307, 407, Expert, FIAT Scudo : - Abgriff im Radioschacht am MOST Stecker, CAN low: Pin 13 grau oder blau CAN high: Pin 10 wei. - Tap off in the radio slot at the MOST connector, CAN low: pin 13 grey or blue CAN high: pin 10 white.
______________________________________________________________________________________ SAAB: - 9-3, 9-5 alle mit Innenraum CAN-Bus. Abgriff im Radioschacht am 10 poligen ISO Stecker. CAN low: Pin 2 wei, CAN high: Pin 4 grn. 9-3 nach Facelift: Abgriff am 20 poligen Stecker des Radiobedienteils. CAN high: Pin 1 oder 2 grn, CAN low wird nicht angeschlossen!!!
- 9-3, 9-5 all with interior CAN-Bus. Tap off in the radio slot at the 10 pin ISO connector. CAN low: pin 2 white, CAN high: pin 4 green. 9-3 after facelift: Tap off at the 20 pin connector located in the back from the radio control panel. CAN high: pin 1 or 2 green, CAN low mustnt be connected!!!
VOLVO: - V70, S60 mit Innenraum CAN Bus. Abgriff im Radioschacht am grnen Stecker CAN high: Pin 7 wei, CAN low: Pin 8 grn. - V70, S60 with interior CAN Bus. Tap off in the radio slot at the green connector, CAN high: pin 7 white CAN low: pin 8 green - V70 ab Modelljahr 2008 mit Innenraum CAN Bus Abgriff unter linker Abdeckung von Mittelkonsole, Hauptkabelstrang mit mehreren verdrillten Aderpaaren. CAN-High: grn orange CAN-Low: lila orange - V70 model year 2008 on with interior CAN Bus. Tap off under left center console cover, main wire with several twisted cable pairs. CAN high: green orange CAN low: purple orange
- XC90 mit Innenraum CAN Bus. Abgriff im Radioschacht am grnen Stecker CAN high: wei CAN low: grn - XC90 with interior CAN Bus. Tap off in the radio slot at the green connector, CAN high: white CAN low: green
- FH12 und FH16 mit Innenraum CAN Bus. ACHTUNG! Nur an +12V anschlieen!!! Abgriff im Radioschacht am Mini ISO Stecker CAN low: Pin 5 grn, CAN high: Pin 1 gelb / schwarz. - FH12 and FH16 with interior CAN Bus. ATTENTION! Connection only to +12V!!! Tap off in the radio slot at the MINI ISO connector, CAN low: pin 5 green, CAN high: pin 1 yellow / black