1. Introduction

The Fantasea BigEye Lens MPK Series is a patented wet accessory wide angle lens that was specially designed for Sony MPK-WE, MPK-WEB, MPK-WD and MPK-WF underwater camera housings. The lens fits onto the housing lens port and can be installed and removed during the course of the dive. It is perfect for photographing seascapes, divers, ship wrecks and schools of fish without moving further away from the subject, thereby still taking full advantage of water clarity and artificial light sources.

2. Technology

The BigEye Lens MPK Series makes use of a new patented lens technology, which allows for high quality underwater wide angle images free of distortions. The new technology uses air instead of glass as an optical element and enables recovering 100% of the camera lens optical properties that would normally be lost underwater. The air pocket inside the lens enhances the angle of light refraction, thereby restoring the original angle of coverage of the camera lens (see figures below). This patented technology was specially designed for underwater photography and therefore the lens should only be used when the system is submerged in water.

3. Included in Packaging

BigEye Lens MPK Series Neoprene Lens Cover Secure Line Warranty Instruction Manual

4. Specifications

For Sony MPK-WE, MPK-WEB, MPK-WD and MPK-WF housings Depth rated to 60 meters / 200 feet Field of view recovery (magnification): 100% (x 0.75) Angle of coverage: Varies according to camera lens specs Lens material: Optical glass, hard coated plastic and anodized aluminum Weight: 489g Dimensions: 157x77mm

5. Instructions for Use

A. Please use the utmost care and do not use excessive force when assembling and disassembling the lens, in order to not cause any damage to the product. B. During the dive, install the BigEye Lens on your housing lens port by following the instructions below and the images on the following page: a. Hold the BigEye Lens in front of the housing lens port so that the TOP marking printed on the lens configuration is pointed upwards. b. To install the BigEye Lens, push it against the lens port starting from the bottom (image A) and proceeding towards the top (image B).

Image A

Image B
C. Attach the secure line to the lens and the housing, in order to secure the lens to the housing. D. Please note that the BigEye Lens was designed to work underwater only. Therefore, the lens should only be installed underwater, while letting water enter the gap between the BigEye Lens and the housing lens port. Make sure that there are no air bubbles trapped between the BigEye Lens and the housing lens port before taking images. E. During the beginning of your dive, your lens might become foggy as a result of an increase in the air temperature inside the lens, following submersion in cooler water. Storing the lens in a cool dry place when not being used, such as a padded housing bag with a few silica gel packs inside, and submerging it in cool water for 10 minutes prior to the dive, will assist in preventing such condensation. However, even if your BigEye Lens starts fogging up at the beginning of the dive due to temperature differences, please note that continuing to dive with it for about 10 minutes will eventually dissolve the fog.

F. When taking photos with the BigEye Lens installed, set your camera focus mode to MACRO. Failing to do so will result in blurred images. G. The BigEye Lens can be removed and installed repeatedly throughout the course of the dive. Whenever removing the lens, set your camera focus to the desired mode, if it is not Macro. H. In order to remove the BigEye Lens from the housing lens port, first detach the secure line and then gently push the BigEye Lens off, starting from the top and proceeding with the bottom. I. When removing the BigEye Lens from the housing, it can be conveniently stored by attaching it to the EyeGrabber MPK Series, which mounts on Fantasea Flex Arms, thereby making it easily available for future use. For further information, please visit our website at www.fantasea.com/FantaseaEyes J. It is recommended to use an external strobe when the BigEye Lens is mounted on the housing. The BigEye Lens blocks the camera internal flash, resulting in underexposed or shaded images. K. When using an external flash, there are a few techniques that should be followed in order to avoid a lens flare, which is often encountered when using dome ports of any kind due to the reflection of the sub or strobe: a. Make sure that the wings of the BigEye Lens are positioned at an angle that blocks the strobe output, as well as the sun. In order to prevent the wings from unintentionally changing position, some friction has been added, but rotating them can be easily done by following a simple technique. In order to rotate the wings, simply hold them and push them against the housing when the BigEye Lens is mounted on your housing lens port. At the same time, rotate them around the lens, till they have reached the desired position. Images in which the sun is captured can be usually taken during mornings or afternoons, when the sun is not as strong as during the middle of the day. In general, the sun will have a much
softer and successful effect during early and late hours of the day and will also cause less of a flare. b. Make sure that the strobe is not positioned towards the lens. When shooting a nearby subject, for instance, it is better to position the strobe a little bit in front of the camera housing rather than behind it (so the light doesn't reflect on the BigEye Lens), or if you choose to position the strobe behind the camera housing, make sure it's not pointed directly towards the lens, but a little bit tilted towards the side.
6. Care & Maintenance
A. Please use the utmost care and do not use excessive force when assembling and disassembling the different accessories, in order not cause any damage to the product. B. Keep the BigEye Lens away from extreme high temperatures, as under direct sunlight, since it might damage the O-ring and interfere with the watertight seal of the lens. C. Do not clean the lens with any chemical solvents or other materials, which might cause damage to the plastic dome. D. Never look at the sun through the lens. E. When storing the lens and during transportation, make sure that it is properly protected in order to prevent scratches, cracks or any other damage to the lens. F. After Dive Care: I. Detach the BigEye Lens from the housing lens port and rinse all lens components in fresh water. II. To ensure that the accumulated salt has completely dissolved, it is recommended to soak the lens in warm fresh water once in a while. III. Wipe the water drops with a soft cloth. Do not leave any droplets to dry on lens surface, as permanent water spots may remain.

Store the lens in a dry and protected area. Storing the lens in a low humidity environment will decrease the chances of the lens fogging up when submerged in water.
Do not store the lens in the presence of chemicals, solvents or fuels.
Complete Compact Digital Housing Accessory System
For further information, please contact us at www.fantasea.com/contact or visit our website www.fantasea.com

Fantasea EyeDaptor MPK-F67

(Cat. No. 4711)

Instruction Manual
The EyeDaptor MPK-F67 enables mounting accessory lenses and filters with a 67mm thread mount on the Sony MPK-WE, MPK-WEB, MPK-WD and MPK-WF housings. Mounting Lens Accessories with a 67mm Thread Mount on Sony MPK-WE/WEB/WD/WF Housings: 1. Please use the utmost care and do not use excessive force when assembling and disassembling the different lens accessories, in order not to cause any damage to the products. 2. Install the EyeDaptor MPK-F67 by attaching it to the housing lens port: a. Hold the adaptor in front of the housing lens port so that the TOP marking printed on the adaptor configuration is pointed upwards (image A).

Image A

EyeDaptor MPK-F67 Instruction Manual
b. To install the adaptor, push it against the lens port starting from the bottom (image B) and proceeding towards the top (image C).

Image B

Image C
c. After adaptor installation, make sure it is properly attached by gently trying to pull it out. If properly installed, the adaptor should not easily come off the lens port. 3. Attach the secure line to the adaptor and the housing, in order to secure the lens and adaptor to the housing. 4. During the dive, install the 67mm threaded accessory lens on the thread of the EyeDaptor MPK-F67 by gently screwing it in. The accessory lens can be installed and removed during the course of the dive. 5. After the dive, detach the accessory lens and adaptor from the housing lens port and rinse all lens components in fresh water. In order to remove the adaptor from the housing lens port, first detach the secure line and then gently push the adaptor off, starting from the top and proceeding with the bottom. 6. Dry and store in a safe protected place.
For further information please contact us at http://www.fantasea.com/contact or visit our website at www.fantasea.com.