SWITCHER PROCESSOR PACK

MVS8000SF-C
MULTI FORMAT SWITCHER PROCESSOR

MVS-8000SF

MKS-8110HD MKS-8110SD MKS-8160HD MKS-8160SD MKS-8170HD MKS-8170SD MKS-8210HD MKS-8210SD MKS-8440HD MKS-8440SD HK-PSU04
OPERATION MANUAL 1st Edition

[English]

WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED.
For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. (MKS-8110HD/8110SD/8160HD/8160SD/8170HD/8170SD/ 8210HD/8210SD/8440HD/8440SD/HK-PSU04 only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For customers in Canada (MKS-8110HD/8110SD/8160HD/ 8160SD/8170HD/8170SD/8210HD/8210SD/8440HD/ 8440SD/HK-PSU04 only) This Class A digital apparatus complies with Canadian ICES003. Pour les utilisateurs au Canada (MKS-8110HD/8110SD/ 8160HD/8160SD/8170HD/8170SD/8210HD/8210SD/ 8440HD/8440SD/HK-PSU04 uniquement) Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada.
WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. If used in USA, use the UL LISTED power cord specified below. DO NOT USE ANY OTHER POWER CORD. Plug Cap Cord Length Rating Parallel blade with ground pin (NEMA 5-15P Configuration) Type SJT, three 16 or 18 AWG wires Less than 2.5 m (8 ft 3 in) Minimum 10 A, 125 V
Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel. WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1 Use the approved Power Cord (3-core mains lead)/ Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2 Use the Power Cord (3-core mains lead)/Appliance Connector/Plug conforming to the proper ratings (Voltage, Ampere). If you have questions on the use of the above Power Cord/ Appliance Connector/Plug, please consult a qualified service personnel.
VORSICHT Um Feuergefahr und die Gefahr eines elektrischen Schlages zu vermeiden, darf das Gert weder Regen noch Feuchtigkeit ausgesetzt werden. Um einen elektrishen Schlag zu vermeiden, darf das Gehuse nicht geffnet werden. berlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. DIESES GERT MUSS GEERDET WERDEN.
AVERTISSEMENT Afin dviter tout risque dincendie ou dlectrocution, ne pas exposer cet appareil la pluie ou lhumidit. Afin dcarter tout risque dlectrocution, garder le coffret ferm. Ne confier
This symbol is intended to alert the user to the presence of important operrating and maintenance (servicing) instructions in the literature accompanying the appliance.
lentretien de lappareil qu un personnel qualifi. CET APPAREIL DOIT TRE RELI LA TERRE.
EN55103-2: Electromagnetic Susceptibility (Immunity) This product is intended for use in the following Electromagnetic Environment: E4 (controlled EMC environment, ex. TV studio). Fr Kunden in Europa (nur MKS-8110HD/8110SD/8160HD/ 8160SD/8170HD/8170SD/8210HD/8210SD/8440HD/ 8440SD/HK-PSU04) Dieses Produkt besitzt die CE-Kennzeichnung und erfllt die EMV-Direktive (89/336/EEC) der EG-Kommission. Die Erfllung dieser Direktive bedeutet Konformitt fr die folgenden Europischen Normen: EN55103-1: Elektromagnetische Interferenz (Emission) EN55103-2: Elektromagnetische Empfindlichkeit (Immunitt) Dieses Produkt ist fr den Einsatz unter die folgende elektromagnetische Bedingung ausgelegt: E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio). Pour les clients europens (MKS-8110HD/8110SD/ 8160HD/8160SD/8170HD/8170SD/8210HD/8210SD/ 8440HD/8440SD/HK-PSU04 uniquement) Ce produit portant la marque CE est conforme la Directive sur la compatibilit lectromagntique (EMC) (89/336/CEE) mise par la Commission de la Communaut europenne. La conformit cette directive implique la conformit aux normes europennes suivantes: EN55103-1: Interfrences lectromagntiques (mission) EN55103-2: Sensibilit lectromagntique (immunit) Ce produit est prvu pour tre utilis dans lenvironnement lectromagntique suivant: E4 (environnement EMC contrl ex. studio de tlvision).

Table of Contents

Overview... 5 Features... 5 Overview of the MVS-8000 Series Components.. 6 Location and Function of Parts.. 7 Front Panel... 7 Rear Panel... 8 Example System Configuration.. 10 MVS-8000 System Configuration.. 10 Flow of Video Signals.. 11 Power Supply Unit Status Indicators.. 12 Specifications... 13 MVS-8000SF Multi Format Switcher Processor. 13 MKS-8110HD 17 Input Board.. 14 MKS-8110SD 17 Input Board.. 14 MKS-8160HD 8 Output Board.. 14 MKS-8160SD 8 Output Board.. 14 MKS-8170HD DME Interface Board.. 15 MKS-8170SD DME Interface Board.. 15 MKS-8210HD Mix/Effect Board Set.. 15 MKS-8210SD Mix/Effect Board Set.. 15 MKS-8440HD Frame Memory Board Set. 16 MKS-8440SD Frame Memory Board Set. 16 HK-PSU04 Power Supply Unit.. 16

Overview

The MVS8000SF-C Switcher Processor Pack is a highperformance, multi-function processor for use in a MVS8000 Multi Format Switcher system. It has a wide range of application, being usable in live production systems in studios and ENG/OB vans as well as in postproduction editing systems. The MVS8000SF-C is a generic name of the switcher processor unit having two or one M/E (mix/effects) option item installed in it.
Simultaneous output of four programs
Each M/E bank is able to handle four simultaneous program outputs, with the ability to apply any of the four keys to program output. This gives the system the ability to handle a wide range of operating situations, for example simultaneous transmission of four programs.
Powerful preview functions
The system supports simultaneous output of look-ahead previews (next preview) and key previews, and also transition previews.
Powerful frame memory functions

Features

Multi format support
By exchange of system boards, this unit supports both HDTV and SDTV signal formats. Between HDTV signal formats or between SDTV signal formats, switching can be made easily from the center control panel of the MVS-8000 system without exchanging system boards. The wide range of supported signal formats allows the unit to be used in many different video production environments. The following signal formats are supported. SDTV formats: 480i/59.94, 576i/50 HDTV formats: 1080i/50, 1080i/59.94, 1080i/60, 1080p/23.976, 1080p/24, 1080p/25, 1080p/29.97, 1080p/30
Up to 58 HDTV still frames and 222 SDTV still frames can be stored in frame memory, and up to eight frames can be called up for use simultaneously. Frames are called up instantly, making it possible to achieve animation effects. Image movement and paint functions are also possible. Still pictures from frame memory can be stored on the internal hard disk drive of the center control panel, and still pictures can be imported from and exported to PCs and other external devices.

Links to DME functions

By connecting the unit to an MVE-8000 DME processor Pack with a special cable, you can apply DME wipes and processed keys and a wide variety of other DME functions as if they were native switcher functions. All DME functions can be controlled from the center control panel of the MVS-8000 system.
Highly expandable system configuration
By combining option boards, you can configure the optimum system for your requirements, selecting HDTV or SDTV, the number of inputs and outputs, and the number of M/E banks. The systems flexibility guarantees its ability to meet future expansion requirements.
Optional backup power supply
By installing two optional HK-PSU04 Power Supply Units, in addition to the two power supplies fitted as standard, this provides a 2:2 fully redundant power supply. Installing a single HK-PSU04 option provides a 2:1 backup system. The system can operate from any two of the three power supplies, reducing the risk of power failure, and increasing the reliability of live broadcasts.

High-performance keyers

Each M/E bank is equipped with four high-performance keyers that provide the following standard functions. Ability to apply transitions to keyers independently of the background Chroma key and color vector keys in each keyer FineKeyTM, and key borders up to 8H Color mixable matte generator available for both key fill and key borders
Overview of the MVS-8000 Series Components
MVS-8000SF Multi Format Switcher Processor
This is a cabinet (size: EIA 8 RU) in which to install option items to provide multi-format switcher processing capabilities. The following option boards and option power supply unit can be installed for HDTV or SDTV systems. HDTV system:
MKS-8170HD DME Interface Board
An interface board for input and output of HDTV signals with the MKS-8800 Multi Format DME Processor. Installation of this board allows up to two MKS-8800 units to be connected to the MVS-8000SF.
MKS-8170SD DME Interface Board
An interface board for input and output of SDTV signals with the MKS-8800 Multi Format DME Processor. Installation of this board allows up to two MKS-8800 units to be connected to the MVS-8000SF.
MKS-8210HD Mix/Effect Board Set
An M/E (mix/effects) board set for HDTV. Systems can be configured with one or two M/E board sets.

Board Name MKS-8110HD MKS-8160HD MKS-8170HD MKS-8210HD MKS-8440HD HK-PSU04
Maximum installable number of boards 1 2
MKS-8210SD Mix/Effect Board Set
An M/E (mix/effects) board set for SDTV. Systems can be configured with one or two M/E board sets.
MKS-8440HD Frame Memory Board Set
A frame memory board set for HDTV. Up to 58 HDTV pictures can be stored and recalled in real time.

SDTV system:

Board Name MKS-8110SD MKS-8160SD MKS-8170SD MKS-8210SD MKS-8440SD HK-PSU04
MKS-8440SD Frame Memory Board Set
A frame memory board set for SDTV. Up to 222 SDTV pictures can be stored and recalled in real time.
HK-PSU04 Power Supply Unit
This is a backup power supply unit. The MVS-8000SF is equipped with two power supplies as standard, but installing two HK-PSU04 units provides a fully redundant power supply. Installing a single HK-PSU04 unit provides a total of three power supplies, and allows the system to operate even if one of the power supplies fails.
MKS-8110HD 17 Input Board
A 17-input board for HDTV. Up to two boards can be installed in the system.
MKS-8110SD 17 Input Board
A 17-input board for SDTV. Up to two boards can be installed in the system.
MKS-8160HD 8 Output Board
An 8-ouput board for HDTV. Up to two boards can be installed in the system.
MKS-8160SD 8 Output Board
An 8-ouput board for SDTV. Up to two boards can be installed in the system.
Location and Function of Parts

Front Panel

Power A, B, C, D switches and status indicators
Power A, B, C, D switches and status indicators The POWER switches turn the unit on and off. The unit is powered on when the POWER switches are on the ? side, and powered off when the POWER switches are on the a side. The status indicators light in green when the unit is powered on. Depending on the configuration of your unit, the HKPSU04 Power Supply Unit may not be installed. In this case, only the POWER A and POWER B switches are available. There is no POWER C or POWER D switch. The unit does not operate until two of the four (A, B, C and D) power switches are on. When using the unit provided with a 2:2 fully redundant power supply, turn all the four power switches on.

Caution

When installing the HK-PSU04 in your unit, be sure to contact your Sony service representative.
If a status indicator does not light when you turn a POWER switch on, there may be a fault in the power circuits. Turn the POWER switch off and contact your Sony service representative.

Rear Panel

6 CTRL connector 7 DATA connector 8 REF IN connectors 9 REF OUT connectors q; EXT connector qa DME 1A, 1B, 2A, and 2B connectors 4 - AC IN A, B, C, and D connectors 5 U terminal 1 REMOTE 1 to 4 connectors 2 GPI connector

3 TERMINAL connector

qs PRIMARY INPUTS 1 to 34 connectors a) qd OUTPUTS 1 to 16 connectors a)
a) This figure shows the rear panel when option boards (MKS-8110HD/8110SD and MKS-8160HD/8160SD) are installed in the unit.
a REMOTE 1 to 4 connectors (D-sub 9-pin, RJ-45) These connectors are used to control the auxiliary bus of the MVS-8000 series from external devices, or to operate the MVS-8000SF from editing control systems such as the BVE-9100. Define the types of the connected devices on the center control panel. b GPI (General Purpose Interface) connector (D-sub 25-pin) Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel. c TERMINAL connector (D-sub 9-pin, RS-232C) This connector is used for factory adjustments. d - AC IN (AC power input) A, B, C, and D connectors (3-pin) Connect to 100 to 240 V AC power supply with the optional AC power cords. Depending on the configuration of your unit, the HKPSU04 Power Supply Unit may not be installed. In that case, the AC IN C and AC IN D connectors are not used. When using the unit provided with a 2:2 fully redundant power supply, connect all the four connectors (A, B, C and D) to the 100 to 240 V AC power supply.
For information about installing an HK-PSU04 Power Supply Unit, contact your Sony service representative. e U (signal ground) terminal Connect to the system ground. f CTRL (control) connector (RJ-45) Connect to an Ethernet switch*. The MKS-8800 Multi Format DME processor and the MVS-8000 systems center control panel are connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily to control the various devices from the center control panel.
* For information about Ethernet switches that can be used in an MVS system, contact your Sony service representative. * Ethernet is a trademark of Xerox Corporation.
For more information about Ethernet switch connectors, see MVS-8000 System Configuration (page 10). For detailed information about setting up the Ethernet switch, refer to the documentation supplied with the switch.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage.
g DATA connector (RJ-45) Connect to an Ethernet switch. The MKS-8800 Multi Format DME processor and the MVS-8000 systems center control panel are connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily for exchange of various types of data (key frame effects, snapshots, etc.) and still pictures of frame memory.

m OUTPUTS 1 to 16 connectors (BNC type) (MKS-8160HD/8160SD) These connectors output serial digital signals. You can assign them freely as program output, preview output, AUX output, and so on. Each output has two connectors. Make output assignments on the MVS-8000 system center control panel. The number of these connectors depends on the number of MKS-8160HD/8160SD boards that are installed in the unit. Refer to the Operation Guide for information about signals that may be assigned.
When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage. h REF IN (reference video input) connectors (BNC type) If you wish to synchronize this unit to an external reference signal, input the reference signal. For an HDTV system, input an HD tri-level sync signal, black burst signal, or analog sync signal. For an SDTV system, input a black burst signal or analog sync signal. The two connectors have a loop-through configuration. Signal input to one connector can be output from the other connector. If you will not be using the loop-through output, be sure to terminate the unused connector with the supplied 75 terminator. i REF OUT (reference video output) connectors (BNC type) These connector output reference video signals. In an HDTV system, they output HD tri-level sync signal or analog sync signal. In an SDTV system, they output analog sync signal. j EXT (extension) connector (BNC type) Connect to a device such as an HDS-X3000 series routing switcher to increase the number of inputs. k DME (Digital Multi Effects input and output) 1A, 1B, 2A, and 2B connectors (MDR 68-pin) Connect to the MVE-8000 with the special cable supplied with the MKS-8800. You can connect up to two MVE-8000 units. Connect the first unit to the DME 1A/1B connectors and the second unit to the DME 2A/2B connectors. l PRIMARY INPUTS 1 to 34 connectors (BNC type) (MKS-8110HD/8110SD) These connectors allow you to input up to 34 serial digital video signals. The number of these connectors depends on the number of MKS-8110HD/8110SD boards that are installed in the unit.
Example System Configuration
MVS-8000 System Configuration
Reference video signal b)

Ethernet switch a)

DATA LAN

CTRL EDITOR

MVE-8000 DME Processor Pack
BVE-9100 Editing Control System

CTRL REMOTE 1

CTRL PERIPH

REMOTE

Reference video signal b) BKS-R Series
MKS-8010 System Control Unit
HDS-X Series MVS8000SF-C Switcher Processor Pack DCU-8000 Device Control Unit Pack

PERIPH

Audio Mixer
a) It is recommended that the CTRL and DATA LAN networks be configured by connecting separate Ethernet switches for each LAN. However, it is also possible to make connections for both LANs on a single Ethernet switch.
b) Terminate with the supplied 75 terminators. Terminators are supplied in the product package.
Cross cable Cable with BNC connectors

Flow of Video Signals

SWITCHER B

SWITCHER A

Reference video signal c) 100 to 240 V AC power supply a) 100 to 240 V AC power supply b)
Reference video signal c)

DME 1B

Camera, VTR, routing switcher PRIMARY INPUTS 1 to 34

DME 1A

100 to 240 V AC power supply b)

Monitor

MVS8000SF-C Switcher Processor Pack

OUTPUTS 1 to 16

Cable with 68-pin connectors
Video input signal Video output signal Video/key signal AC power supply
a) For the AC power cord of the MVE-8000 DME Processor Pack, refer to Accessories not supplied for MKS-8000 Multi Format DME Processor in the MVE-8000 Operation Manual.
b) For the AC power cord of this unit, see Accessories not supplied (page 13) in this manual. c) Terminate with the supplied 75 terminators. Terminators are supplied in the product package.
Power Supply Unit Status Indicators
The power supply unit status indicators show the status of the power supply unit during operation and when the unit is powered on. Whenever a power error is detected, it is reflected immediately by the indicator.
Meaning of status indicator displays Indicator Status color Green Red Lit LIt Not lit Description Operating normally Steps to take
Power supply unit fan Exchange the fault fan unit Power supply unit fault Exchange the power unit
When the unit is powered on, the status indicators may light momentarily in red and a whining sound may be heard. This is not a malfunction. Power all of the installed power supply units on. When some of the power supply units are off and some are on, the status indicators of the units which are off may light in red. This is not a malfunction.

Specifications

TERMINAL The following specifications show the reference performance for this unit and individual option boards/ units. Design and specifications are subject to change without notice. EXT
Relay contact outputs: 4 (30 V AC/DC, 0.1 A) Open collector outputs: 4 D-sub 9-pin, female Complies with RS-232C standard Data transfer rate: 9600 bps BNC type, 75 S-BUS data transfer rate: 312/1250 Kbps
Reference input and output
REF IN BNC type, 75 with loop-through output HDTV systems: HD tri-level sync/SDTV analog black burst/SDTV analog sync SDTV systems: Analog black burst/analog sync BNC type, 75 HD tri-level sync (HDTV systems only) Signal level 300 mV 10% Analog sync Signal level 300 mV 10% Phase variation range 90H to +90H

General

Power requirements 100 to 240 V AC, 50/60 Hz Power consumption 100 V: 10 A, 240 V: 4.2 A Operating temperature 5C to 40C (41F to 104F) Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (230 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Performance guaranteed temperature 10C to 35C (50F to 95F) Storage temperature 20C to +60C (4F to +140F) Operating humidity 10% to 90% Dimensions (w/h/d, excluding projections) 482354520 mm (1914201/2 inches) Mass Approx. 45 kg (99 lb 3 oz) (when equipped with all installable option boards and option power supply unit) REF OUT

AC input

AC IN A, B, C, D 3-pin AC connector

Accessories supplied

75 terminator (1) Operation Manual (1) Installation Manual (1)

Accessories not supplied

AC power cord (for USA and Canada only) (125 V 10 A 2.4 m (8 ft)) (Part No.: 1-557-377-11) AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft)) (Part No.: 1-782-929-21)
Remote Control connectors
CTRL RJ-45 Complies with 100Base-TX standard DATA RJ-45 Complies with 100Base-TX standard REMOTE 1, 2, 3, 4 D-sub 9-pin, female Comply with RS-422A standard Data transfer rate: 38.4 Kbps GPI D-sub 25-pin, female TTL inputs: 8
Power requirements 12 V DC Power consumption Max. 10 W Dimensions (w/d) 27494 mm (107/833/4 inches) Mass Approx. 1 kg (2 lb 3 oz)
Power requirements 12 V DC Power consumption Max. 110 W Dimensions (w/d) OUT board: 317380 mm (121/215 inches) CN board: 27494 mm (107/833/4 inches) Mass Approx. 3 kg (6 lb 9 oz)
Inputs 17 (BNC type) Signal format SMPTE292M Signal level 0.8 V p-p 10% Signal transfer rate 1.5 Gbps Return loss 15 dB Cable length 100 m (5C-FB cable, BELDEN1694 or equivalent)

Output

Outputs 8 (BNC type), each with 2 outputs Signal format SMPTE292M Signal level 0.8 V p-p 10% Signal transfer rate 1.5 Gbps
Operation and Installation Guide (1) (supplied only when product is purchased separately)

Power requirements 12 V DC Power consumption Max. 80 W Dimensions (w/d) OUT board: 317380 mm (121/215 inches) CN board: 27494 mm (107/833/4 inches) Mass Approx. 3 kg (6 lb 9 oz)
Inputs 17 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal transfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-FB cable, BELDEN8281 or equivalent)
Outputs 8 (BNC type), each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal transfer rate 270 Mbps
Power requirements 12 V DC Power consumption Max. 50 W Dimensions (w/d) DIF board: 317380 mm (121/215 inches) CN board: 27494 mm (107/833/4 inches) Mass Approx. 1 kg (2 lb 3 oz)
Power requirements 12 V DC Power consumption Max. 250 W Dimensions (w/d) MIX board: 317380 mm (121/215 inches) KPC board: 317380 mm (121/215 inches) DI board: 317380 mm (121/215 inches) DO board: 317380 mm (121/215 inches) Mass Approx. 5 kg (11 lb) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)
Input and output (DME 1A, DME 1B, DME 2A, DME 2B)
Connector Signal format MDR 68-pin LVDS
Power requirements 12 V DC Power consumption 150 W Dimensions (w/d) MIX board: 317380 mm (121/215 inches) KPC board: 317380 mm (121/215 inches) DI board: 317380 mm (121/215 inches) DO board: 317v380 mm (121/215 inches) Mass Approx. 5 kg (11 lb) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)
Power requirements 12 V DC Power consumption Max. 70 W Dimensions (w/d) MY board: 317380 mm (121/215 inches) DIO board: 317380 mm (121/215 inches) Mass Approx. 2 kg (4 lb 6 oz) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)
Accessories supplied Installation Guide (1) (supplied only when product is purchased separately)
Power requirements 12 V DC Power consumption Max. 50 W Dimensions (w/d) MY board: 317380 mm (121/215 inches) DIO board: 317380 mm (121/215 inches) Mass Approx. 2 kg (4 lb 6 oz) Accessories supplied Operation and Installation Guide (1) (supplied only when product is purchased separately)
Power requirements 100 to 240 V AC, 50/60 Hz Output power 12 V DC 0.5 V Power consumption 100 V: 10 A, 240 V: 5 A Secondary power supply Max. 60 A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (230 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 40 A (230 V) Dimensions (w/h/d) 9483396 mm (33/433/8155/8 inches) Mass Approx. 3 kg (6 lb 9 oz)

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation. Le matriel contenu dans ce manuel consiste en informations qui sont la proprit de Sony Corporation et sont destines exclusivement lusage des acqureurs de lquipement dcrit dans ce manuel. Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des oprations ou entretiens de lquipement moins dune permission crite de Sony Corporation. Das in dieser Anleitung enthaltene Material besteht aus Informationen, die Eigentum der Sony Corporation sind, und ausschlielich zum Gebrauch durch den Kufer der in dieser Anleitung beschriebenen Ausrstung bestimmt sind. Die Sony Corporation untersagt ausdrcklich die Vervielfltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben fr irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausrstung ohne ausdrckliche schriftliche Erlaubnis der Sony Corporation.

Sony Corporation

B & P Company
MVS-8000SF (SY) 3-620-580-01 (1) http://www.sony.net/
Printed on recycled paper
Printed in Japan 2002.07.13 2002

DIF-119 board _ DIF-122 board _ DI-40 board DO-41 board MIX-45 board KPC-16 board _ _ _ _ _ _ _ _ _ _ _ _ _
MKS-8210SD Mix/Effect Board Set
DI-41 board DO-42 board MIX-45 board KPC-16 board
MKS-8440HD Frame Memory Board Set MKS-8440SD Frame Memory Board Set HK-PSU04 Power Supply Unit
DIO-62 board MY-102 board DIO-63 board MY-102 board _
Installation Procedure 1. Turn off the main power of the MVS-8000SF and disconnect the AC power cord from the wall outlet. 2. Loosen the four screws (with drop-safe) and remove the front panel to the arrow.

Screws (with drop-safe)

4. While the eject levers are opened as shown in the illustration, insert the plug-in board into the board guide rail.
Front panel Screws (with drop-safe)
3. Remove the six screws and remove the plug-in board loose-proof assembly.

Eject levers

B3 x 5
Extract PWB stopper assembly B3 x 5
Name of option MKS-8210HD/SD*1
Name of board DO-41/DO-42 board MIX-45 board KPC-16 board DI-40/DI-41 board
Slot on the front side 3, 8 4, 9 5, 10 6, 14 , 17
5. While closing the eject levers in the direction of arrow 1, push in the plug-in board.
MKS-8170HD/SD MKS-8160HD/SD*2 MKS-8440HD/SD
DIF-119/DIF-122 board OUT-23/OUT-24 board DIO-62/DIO-63 board MY-102 board
*1 : Note when installing the MKS-8210HD/8210SD The MKS-8210HD/8210SD must be inserted into the specified slot only for M/E. Be sure to insert it into the correct slot without fail. The slots into which the MKS-8210HD/8210SD can be inserted are determined in accordance with the configuration of M/Es as shown in the following table.
Slot SLOT 3 to 6 SLOT 8 to 11

M/E M/E 1 PGM/PST

*2 : Relation between the slots in which OUT-23/OUT-4 boards (MKS8160HD/8160SD) are installed and OUTPUT is shown below.

Slot SLOT 14 SLOT 15

OUTPUT 1 to to Eject lever 1 Eject lever
6. Attach the plug-in board loose-proof assembly and the front panel by reversing the installation steps of 2, 3.
1-4-2. Installing the Connector Board
1. Remove the two screws and remove the blank panel. n To install the connector board into the slot in which the other board is installed already, loosen the two fixing screws and remove the connector board that is installed already.
2. Insert the connector board horizontally level and secure it with the two fixing screws.

Fixing screw

Connector board Fixing screw
B3 x 5 Blank panel B3 x 5
Name of option MKS-8110HD MKS-8110SD MKS-8160HD
Name of board CNI-9 board CNI-10 board CNO-11 board CNO-17B board
Slot on the rear side IN 1 to to 34 Insert into the slot on the rear that corresponds to the slot on the front side.
n Store the removed blank panel in a safe place.

MKS-8160SD

1-4-3. Installing the HK-PSU04
The HK-PSU04 is used after it is installed in the MVS8000SF. n Before installing the HK-PSU04, be sure to turn off the main power. If the HK-PSU04 is installed while the main power is turned on, it can result in electrical shock or damage to printed circuit boards. Installation procedure 1. Remove the front panel of the MVS-8000SF. (Refer to Section 1-4-1.) 2. Remove the two screws (B3 x 5) fixing the power supply cover, and remove the power supply cover. 3. Remove the two screws (PSW3 x 6) fixing the blank panel to the location where the HK-PSU04 is going to be installed. Then remove the blank panel.
4. Push the portion of the HK-PSU04 marked by the arrow and insert the HK-PSU04 into deep end as far as it will go. 5. Secure the HK-PSU04 with the two screws removed in step 3.

HK-PSU04

PSW3 x 6

Blank panel B3 x 5

6. Attach the power supply cover and the front panel by reversing the installation steps of 1, 2.

PSW 3x6 PS cover

1-5. Rack Mounting
The MVS-8000SF is mounted in the 19-inch standard rack. To mount the MVS-8000SF in the rack, use the specified rack mount kit and follow the procedure described below. Specified rack mount kit : RMM-10 n If other than the specified rack mount kit is used, the unit may not be mounted in the 19-inch standard rack. Parts of the RMM-10. Rack tool. Right rack mount adapter. Left rack mount adapter. Rack tool attaching screw (B4 x 6 : 7-682-560-09). Rack tool attaching screw (B4 x 10 : 7-682-560-10)
2. Rack Mounting Procedure This section describes the rack mounting procedure using the RMM-10 rack mount kit. n Tighten the screws to the following torque. Tightening torque : 120 x 10_2 N.m {12.2 kgf.cm} 1. Attach the rack tool to the side of the equipment using the specified six screws. n Use B4 x 6 screws.

B4 x 6 Rack tool

2 pcs 1 pc 1 pc 6 pcs 6 pcs
Other required parts To mount in the rack, the rack mount kit RMM-10 and the following part are required. Screw for rack mounting 4 pcs (B5 x 12 : 7-682-576-04) 1. Precautions for Rack Mounting w. To prevent the rack from falling or moving, fix the rack on a flat and steady floor using bolt or others. If the rack falls due to the weight of the equipment, it may cause death or injury. Be sure to use the specified rack mount kit. If not, injury may result and the equipment may fall due to insufficient strength. After rack mounting, be sure to tighten the screws on the rack angle and fix the unit in the rack. If the screws on the rack angle are not tightened, the unit may slip from the rack and fall, causing injury. c When mounting the unit in the rack, note the following:. Be sure to mount in the rack with two persons or more. Be careful not to catch your fingers or hands in the rack mount rail or others. Mount in the rack in a stable position. n If several units are mounted in a rack, it is recommended to install a ventilation fan to prevent temperature rise inside the rack. 1-8

Rack tool

B4 x 6
2. Loosen the screws on the rear of the right and left adapters and adjust the length of the adapter according to the depth of the rack. (The illustration below shows the left adapter.)
6. Align the groove of the rack tool at the side of the equipment with the rail, and slide the equipment to the rear. n The rack tools are hooked on the rails as shown below.

Adapter

Portion of the rail B4 x 6
n Maximum depth of adapter : 750 mm Minimum depth of adapter : 595 mm 3. Attach the right and left adapters to the rack completely using the specified six screws. (The illustration below shows the left adapter.)
7. Fix the rack angle in the rack using the specified screws.

B5 x 12

8U B4 x 10 4U
1U 31.75 B4 x 10 Unit : mm
4. Tighten the screws (B4 x 6 : two screws each on the right and left) for adjusting the length of the adapter completely (the screws that were loosened in step 2). 5. Remove the front panel of the equipment. (Refer to Section 1-4-1.)
8. Attach the front panel to the equipment. (Refer to Section 1-4-1.)

1-6. Matching Connectors

Use the following connectors, cables or equivalents when connecting cables to the unit.
Model name Panel indication Connector name Matching connector and cable Name MKS-8110SD/HD MKS-8160SD/HD PRIMARY INPUTS 1 to 17 OUTPUTS 1 to 8 BNC, 75 Z Belden 8281 coaxial cable (SDTV system) or Belden 1694 coaxial cable (HDTV system) MVS-8000SF REF IN REF OUT EXT REMOTE 1 to 4 TERMINAL D-sub 9-pin, Female D-sub 9-pin, Male Connector 9-pin, Male Junction Shell 9-pin GPI D-sub 25-pin, Female D-sub 25-pin, Male Connector 25-pin, Male 1-560-904-11*1 Junction Shell 25-pin DATA CTRL DME 1A, 1B, 2A, 2B MDR 68-pin, Female Dedicated cable (supplied with the MVE-8000) _ RJ-45 modular jack

Sony part No. _

BNC, 75 Z
Belden 8281 coaxial cable
1-560-651-00*1 1-561-749-00

1-563-377-11 _

*1 : The following crimp contact is required for the plug. AWG#18 to #22 : 1-566-493-21 AWG#22 to #24 : 1-564-774-11 AWG#24 to #30 : 1-564-775-11 *2 : Conforms to the IEEE 802.3 Ethernet 100BASE-TX standards.
1-7. Input/Output Signals of Connectors
The input/output signals of the connectors at the rear panel are as follows. TERMINAL : RS-232C (D-sub 9-pin, Female) to Terminal

Pin No. 25

TP1000 (E-9), TP1500 (F-9), TP2000 (G-9), TP2500 (J-9), TP3000 (K-9), TP3500 (M-9), TP4000 (K-4), TP4500 (J-4), TP6000 (H-4) : PLL LOCK signal check terminal (DO-41 board) PLL-LOCK signal measuring terminal. TP1001 (C-10), TP1501 (E-10), TP2001 (F-10), TP2501 (H-10), TP3001 (J-10), TP3501 (K-10), TP4001 (M-3), TP4501 (K-3), TP6001 (J-3) : EAV_C signal check terminal (DO-41 board) EAV_C signal measuring terminal. TP1001 (D-10), TP1501 (F-10), TP2001 (G-10), TP2501 (H-10), TP3001 (K-9), TP3501 (L-9), TP4001 (L-3), TP4501 (J-3), TP6001 (H-3) : EAV_C signal check terminal (DO-42 board) EAV_C signal measuring terminal. TP1002 (C-9), TP1502 (E-9), TP2002 (F-9), TP2502 (H-9), TP3002 (J-9), TP3502 (K-9), TP4002 (M-3), TP4502 (K-3), TP6002 (J-3) : EAV_Y signal check terminal (DO41 board) EAV_Y signal measuring terminal. TP1002 (D-10), TP1502 (F-10), TP2002 (G-10), TP2502 (J-10), TP3002 (K-9), TP3502 (L-9), TP4002 (L-3), TP4501 (J-3), TP6002 (H-3) : EAV_Y signal check terminal (DO-42 board) EAV_Y signal measuring terminal. TP1000 (D-8), TP1500 (E-8), TP2000 (F-8), TP2500 (H-8), TP3000 (J-8), TP3500 (L-8), TP4000 (L-4), TP4500 (K-4), TP6000 (H-4) : VCO-FRQ signal check terminal VCO-FRQ signal measuring terminal.
3. MIX-45 board (MKS-8210HD/SD)

S1701 D3704

4 TP3700
D3702 TP3723 D3701 TPD3700 TP3702

TP3605 TP3610

TP3611

TP3606

E3719 CN1703 DD2204 D2205 S1702 D1 D2 D2201 D2202 D2206 TP1702 TP1801
D12 D18 D19 D14 D15 D16 D17 SW2 SW1 D10 D13

CPU-DR Module

TP3607 TP3604 TP3602 TP3603 TP3601
<LED> D1 (A-9) : MIXER (Y) status LED MIXER (Y) configuration status indication Lit : Configuring not completed. Not lit : Configuring completed. D2 (A-9) : MIXER (C) status LED MIXER (C) configuration status indication Lit : Configuring not completed. Not lit : Configuring completed. D2201 (A-9) : TBC-A system status LED TBC-A system configuration status indication Lit : Configuring not completed. Not lit : Configuring completed.
D2202 (A-10) : TBC-B system status LED TBC-B system configuration status indication Lit : Configuring not completed. Not lit : Configuring completed. D2203, D2204, D2205 (A-8) : MIX-CPU status LED Indicates the CPU status on the MIX board. D2206 (A-10) : P-XPT status LED PXPT configuration status indication Lit : Configuring not completed. Not lit : Configuring completed. D3700 (A-5) : +1.8 V +1.8 V power supply status indication. Lit when the +1.8 V power is supplied.

D3701 (A-5) : +2.5 V +2.5 V power supply status indication. Lit when the +2.5 V power is supplied. D3702 (A-4) : +3.3 V +3.3 V power supply status indication. Lit when the +3.3 V power is supplied. D3704 (A-4) : +12 V +12 V power supply status indication. Lit when the +12 V power is supplied. If this LED does not light on, the fuse may have blown. <Switch> S1701 (A-4) : MIX-CPU reset switch Pressing this switch initializes the CPU on the MIX-45 board. S1702 (A-8) : Monitor reset switch The reset switch that is used to reset the monitor during maintenance through the terminal. <Connector> CN1703 (A-8) : TERMINAL pin TERMINAL pin This pin is connected to the control terminal and used during maintenance. Conforms to RS-232C. CN2201 (A-6) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP. <TEST terminal> E3719 (A-7) : GND terminal Use this terminal as the earth point for measuring the respective check terminals. TP1702 (B-8) : CPU CK (CPU clock) signal check terminal Use this terminal to check the CPU clock for video signal. TP1801 (K-7) : DLY_WE terminal Use this terminal to check the Write_Enable signal of the delay circuit. TP3601 (N-13) : FLOE (field odd even) signal check terminal Use this terminal to check the FLOE signal from the mother board. TP3602 (N-13) : HD (horizontal sync) signal check terminal Use this terminal to check the HD signal supplied from mother board.
TP3603 (N-12) : CKX (control timing) signal check terminal Use this terminal to check the CKX signal supplied from mother board. TP3604 (N-12) : VD (vertical sync) signal check terminal Use this terminal to check the VD signal supplied from mother board. TP3605 (N-5) : Buffered VD0 (vertical sync) signal check terminal Use this terminal to check the VD signal that is used on this board. TP3606 (P-6) : Buffered CKX0 (switching) signal check terminal Use this terminal to check the CKX signal that is used in this circuit board. TP3607 (N-12) : CK (clock for video) signal check terminal Use this terminal to check the clock for video signal that is used in this circuit board. TP3610 (N-6) : Buffered HD0 (horizontal sync) signal check terminal Use this terminal to check the HD signal that is used in this circuit board TP3611 (N-7) : Buffered FLOE0 (field odd even) signal check terminal Use this terminal to check the FLOE signal that is used in this circuit board. TP3700 (A-4) : +12 V check terminal +12 V measuring terminal. TP3702 (A-5) : +1.8 V check terminal +1.8 V measuring terminal. TP3717 (A-5) : +2.5 V check terminal +2.5 V measuring terminal. TP3723 (A-4) : +3.3 V check terminal +3.3 V measuring terminal. <LED on the CPU DR module> (C11) Refer to < LED on the CPU DR module > in 1. CA-44 board. <Switch on the CPU DR module> (C11) Refer to < Switch on the CPU DR module > in 1. CA-44 board. 1-21

TP6060 (A-2) : +3.3 V check terminal +3.3 V measuring terminal. TP6061 (A-4), TP6067 (G-1), TP6068 (F-4) : +1.8 V check terminal +1.8 V measuring terminal. TP6101 (N-13) : VD (vertical sync) signal check terminal Used to check the VD signal supplied from the mother board. TP6102 (N-13) : CKX (control timing) signal check terminal Used to check the CKX signal supplied from the mother board. TP6103 (N-13) : HD (horizontal sync) signal check terminal Used to check the HD signal supplied from the mother board. TP6104 (N-12) : FLOE (field odd even) signal check terminal Used to check the FLOE signal supplied from the mother board. TP6800 (N-13) : HALF VIDEO CLOCK signal check terminal Used to check the HALF VIDEO CLOCK signal. TP6801 (N-10) : VCLK (clock for video signal) signal check terminal Used to check the clock for video signal TP6802 (A-11) : DLY_WE terminal Used to check the Write-Enable signal of the delay circuit.
5. DI-40 board (MKS-8210HD)/DI-41 board (MKS-8210SD)

D1 TP3 D2 TPD3 TP2

D6 CN1 S1 E1
TP3007 TP3006 TP3002 TP3005 TP3004 TP3001 TP3003 TP3000
TP3507 TP3506 TP3502 TP3505 TP3504 TP3501 TP3503 TP3500
TP8007 TP8006 TP8002 TP8005 TP8004 TP8001 TP8003 TP8000
TP4007 TP4006 TP4002 TP4005 TP4004 TP4001 TP4003 TP4000
TP4507 TP4506 TP4502 TP4505 TP4504 TP4501 TP4503 TP4500
TP5507 TP5506 TP5502 TP5505 TP5504 TP5501 TP5007 TP5006 TP5002 TP5005 TP5004 TP5001 TP5003 TP5000

TP5503 TP5500

E7 TP2000 TP2003 TP2001 TP2004 TP2005 TP2002
TP2500 TP2503 TP2501 TP2504 TP2505 TP2502
TP1000 TP1003 TP1001 TP1004 TP1005 TP1002 TP1006 TP1007
TP1500 TP1503 TP1501 TP1504 TP1505 TP1502 TP1506 TP1507
TP7000 TP7003 TP7001 TP7004 TP7005 TP7002 TP7006 TP7007
TP7500 TP7503 TP7501 TP7504 TP7505 TP7502 TP7506 TP7507
TP6500 TP6503 TP6501 TP6504 TP6505 TP6502 TP6506 TP6507
TP6000 TP6003 TP6001 TP6004 TP6005 TP6002

TP201 TP202 TP203 TP204

DI-40 board A side/Component side

TP3001

TP3501 TP4001

TP4501

TP5001 TP5501
D1 TP3 D2 TPD3 TP2 E1 DD6 CN1

TP4000

TP4500

TP5000

TP5500
E6 TP2000 TP2500 TP1000 TP1500 TP7000 TP7500 TP6500 TP6000
TP2501 TP2001 TP1001 TP1501 TP7001 TP7501 TP6501 TP6001
E7 TP201 TP202 TP203 TP204
DI-41 board A side/Component side
<LED> D1 (A-3) : +12 V +12 V power supply status indication. Lit when the +12 V power is supplied. If this LED does not light, the fuse may have blown. D2 (A-4) : +3.3 V +3.3 V power supply status indication. Lit when the +3.3 V power is supplied. D3 (A-4) : +2.5 V +2.5 V power supply status indication. Lit when the +2.5 V power is supplied. D5 (A-5) : CONF1 status LED H2 to L2 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuring is complete.
D6 (A-5) : CONF2 status LED D10 to L10 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuring is complete. <Switch> S1 (A-6) : DI reset switch Pressing this switch initializes the DI-40 and D-I41 boards. <Connector> CN1 (A-6) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP. <TEST terminal> E1 (C-6), E2 (J-2), E3 (P-5), E4 (B-11), E5 (H-11), E6 (N-8), E7 (A-7) : GND terminal bard Use this terminal as the earth point for measuring the respective check terminals.

<LED on the CPU DK module> (C-10) Refer to < LED on the CPU DK module > in 1. CA-44 board. <Switch on the CPU DK module> (C-10) Refer to < Switch on the CPU DK module > in 1. CA-44 board.
8. OUT-23 board (MKS-8160HD)/OUT-24 board (MKS-8160SD)
TP1306 TP1206 TP1106 TP1006 S100 D100 TP101 D104 TP102 D105 TP103 D106 TP104 D1400 D1401 CN1400

TP1308 TP1307

TP1208 TP1207

TP1108 TP1107

TP1008 TP1007
TP502 TP1001 TP1000 TP1002 TP1005 TP1004 TP1003 TP501
E103 E102 TP206 TP207 S1501

CN1502 D503 D502 D501

DI1 DI4 SW2
TP908 TP907 TP808 TP807 TP708 TP707 TP608 TP607

CPU-DK Module*

TP601 TP600 E104 TP205 TP203 TP204 TP602 TP605 TP604 TP603 TP202 TP201 E105

D8 D7 D6 D3 D2

* : The CPU-DK module is installed only in the OUT-23 board of slot 14.
OUT-23 board A side/Component side

TP1301

TP1201

TP1101

TP1001
S100 D100 TP101 D107 D104 TP102 D105 TP103 D106 TP104 D1400 D1401 CN1400

TP1302

TP1202

TP1102

TP1002 TP502

TP1300

TP1200

TP1100

TP501 E107
S1501 CN1502 D503 D502 D501 TP901 TP801 TP701 TP601
TP900 TP902 TP800 TP802 TP700 TP702 TP600 TP602 TP204 TP203 TP202 TP201 E105

E104 TP205

* : The CPU-DK module is installed only in the OUT-24 board of slot 14.
OUT-24 board A side/Component side
<LED> D100 (A-3) : +12 V +12 V power supply status indication. Lit when the +12 V power is supplied. If this LED does not light, the fuse may have blown. D104 (A-3) : +5 V (OUT-23 board) +5 V power supply status indication. Lit when the +5 V power is supplied. D104 (A-4), D107 (A-3) : +5 V (OUT-24 board) +5 V power supply status indication. Lit when the +5 V power is supplied. D105 (A-4) : +3.3 V +3.3 V power supply status indication. Lit when the +3.3 V power is supplied.

D106 (A-4) : +2.5 V +2.5 V power supply status indication. Lit when the +2.5 V power is supplied. D501, D502, D503 (A-8) : OUT-CPU status LED OUT-23 board CPU status indication. D1400 (A-5) : TBC-1 system status LED TBC-1 system configuration status indication Lit : Configuring not completed. Not lit : Configuring completed. D1401 (A-5) : TBC-2 system status LED TBC-2 system configuration status indication Lit : Configuring not completed. Not lit : Configuring completed.
<Switch> S100 (A-3) : OUT-CPU RESET switch Pressing this switch initializes the CPU on the OUT-23/24 board. S1501 (A-7) : MONITOR reset switch The reset switch that is used to reset the monitor during maintenance through the terminal. <Connector> CN1400 (A-5) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP. CN1502 (A-8) : TERMINAL pin This pin is connected to the control terminal and used during maintenance. <TEST terminal> E102 (E-7), E103 (H-6), E104 (J-12), E105 (P-13), E107 (P-6) : GND terminal (OUT-23 board) Use this terminal as the earth point for measuring the respective check terminals. E103 (J-6), E104 (K-13), E105 (P-13), E107 (P-5), E109 (D-13), E108 (J-1), E1010 (P-1) : GND terminal (OUT-24 board) Use this terminal as the earth point for measuring the respective check terminals. TP101 (A-3) : +12 V check terminal +12 V measuring terminal. TP102 (A-4) : +5 V check terminal +5 V measuring terminal. TP103 (A-4) : +3.3 V check terminal +3.3 V measuring terminal. TP104 (A-4) : +2.5 V check terminal (OUT-23 board) +2.5 V measuring terminal. TP104 (A-5) : +2.5 V (OUT-24 board) +2.5 V measuring terminal. TP201 (P-13) : VD (vertical sync) signal check terminal VD signal measuring terminal. TP202 (P-12) : CKX (control timing) signal check terminal CKX signal measuring terminal.
TP203 (N-12) : HD (horizontal sync) signal check terminal (OUT-23 board) HD signal measuring terminal. TP204 (N-13) : FLOE (field odd even) signal check terminal FLOE signal measuring terminal. TP203 (P-12) : HD (horizontal sync) signal check terminal (OUT-24 board) HD signal measuring terminal. TP204 (P-12) : FLOE (Field Odd Even) signal check terminal FLOE signal measuring terminal. TP205 (J-13), TP206 (J-7) : CK (clock for video) signal check terminal (OUT-23 board) Uses this terminal when checking the clock signal for video. TP205 (J-13), TP206 (J-6) : EAV_C signal check terminal (OUT-24 board) CLOCK signal measuring terminal. TP207 (K-7) : VCO CLOCK signal check terminal (OUT-23 board) VCO CLOCK signal measuring terminal. TP501 (P-5) : CPU_OE signal check terminal CPU_OE signal measuring terminal. TP502 (P-5) : CPU_WE signal check terminal CPU_WE signal measuring terminal. TP600 (N-12), TP1000 (N-5) : 1R001 signal check terminal (OUT-23 board) 1R001 signal measuring terminal. TP601 (N-12), TP1001 (N-5) : HANC signal check terminal (OUT-23 board) HANC signal measuring terminal. TP602 (N-11), TP1002 (N-5) : LINE signal check terminal (OUT-23 board) LINE signal measuring terminal. TP603 (N-12), TP1003 (N-5) : FRAME signal check terminal (OUT-23 board) FRAME signal measuring terminal.

TP604 (N-12), TP1004 (N-5) : CRC signal check terminal (OUT-23 board) CRC signal measuring terminal. TP605 (N-11), TP1005 (N-5) : SIG_DET signal check terminal (OUT-23 board) SIG_DET signal measuring terminal. TP606 (N-8), TP706 (L-9), TP806 (J-9), TP906 (G-9), TP1006 (N-2), TP1106 (L-2), TP1206 (J-2), TP1306 (F-2) : PLL_LOCK signal check terminal (OUT-23 board) PLL_LOCK signal measuring terminal. TP607 (N-10), TP707 (L-10), TP807 (J-10), TP907 (G-10), TP1007 (N-4), TP1107 (L-4), TP1207 (J-4), TP1307 (F-4) : EAV_Y signal check terminal (OUT23 board) EAV_Y signal measuring terminal. TP602 (P-10), TP702 (L-10), TP802 (J-10), TP902 (G-10), TP1002 (N-4), TP1102 (L-4), TP1202 (J-4), TP1302 (F-4) : EAV_Y signal check terminal (OUT-24 board) EAV_Y signal measuring terminal. TP608 (N-10), TP708 (L-10), TP808 (J-10), TP908 (G-10), TP1008 (N-3), TP1108 (L-3), TP1208 (J-4), TP1308 (F-4) : EAV_C signal check terminal (OUT-23 board) EAV_C signal measuring terminal. TP600 (M-12), TP601 (M-8), TP700 (K-11), TP701 (K-8), TP800 (H-12), TP801 (H-8), TP900 (E-12), TP901 (F-8), TP1000 (M-5), TP1001 (M-2), TP1100 (J-5), TP1101 (K-2), TP1200 (G-5), TP1201 (G-2), TP1300 (E-5), TP1301 (E-2) : V_FRQ signal check terminal (OUT-24 board) V_FRQ signal measuring terminal. <LED on the CPU DK module> (C10) Refer to < LED on the CPU DR module > in 1. CA-44 board. <Switch on the CPU DK module> (C10) Refer to < Switch on the CPU DR module > in 1. CA-44 board.
9. DIO-62 board (MKS-8440HD)/DIO-63 board (MKS-8440SD)
D1 TP2000 TP2001 TP2002 TP2501 TP2502 TP2500 TP3001 TP3002 TP3000 TP3501 TP3502 TP3500 E1
D5 TPD6 TP1 DTP3 D100 D101 E5

TP4 E2

E6 TP4001 TP4002

TP4000 TP4501 TP4502

TP4500 TP5001 TP5002

TP5501 TP5502

TP1007 TP1006 TP1002 TP1005 TP1004 TP1001 TP1503 TP1000 E7 TP6 TP5 TP1507 TP1506 TP1502 TP1505 TP1504 TP1501 TP1503 TP1500 E3
DIO-62 board A side/Component side

DTP2 D6 TPD7 TP3

TP2500

TP3500 E1

E5 TP3501 TP3502

TP2001 TP2002

TP2501 TP2502

TP3001 TP3002

D100 D101

6 CN1 7

S1 TP4000

E4 TP4500

TP4 E2 TP5000 TP5500
TP1001 TP1501 TP5501 TP5502 E3

TP1000 TP1500

TP4001 TP4002

TP4501 TP4502

TP5001 TP5002

TP7 TP8 TP9 TP10 TP6 TP5

DIO-63 board A side/Component side
<LED> D1 (A-3) : +12 V +12 V power supply status indication. Lit when the +12 V power is supplied. If this LED does not light, the fuse may have blown. D5 (A-3) : +5 V (DIO-62 board) +5 V power supply status indication. Lit when the +5 V power is supplied. D6 (A-4) : +3.3 V +3.3 V power supply status indication. Lit when the +3.3 V power is supplied. D7 (A-5) : +2.5 V +2.5 V power supply status indication. Lit when the +2.5 V power is supplied.

D100 (A-5) : CONF1 H2 to L2 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuring is complete. D101 (A-6) : CONF2 D10 to L10 FPGA (Spartan II) CONFIG DONE status indication. Not lit when configuring is complete. <Switch> S1 (A-7) : DIO reset switch Pressing this switch initializes the CPU on the DIO-62 and DIO-63 board. <Connector> CN1 (A-6) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP.
<TEST terminal> E1 (N-3), E2 (P-6), E3 (P-11), E4 (H-6), E5 (F-3), E6 (A-8), E7 (E-12) : GND terminal (DIO-62 board) Use this terminal as the earth point for measuring the respective check terminals. E1 (N-2), E2 (P-6), E3 (P-10), E4 (H-6), E5 (F-3), E6 (A-5), E7 (A-12) : GND terminal (DIO-63 board) Use this terminal as the earth point for measuring the respective check terminals. TP1 (A-4) : +3.3 V check terminal +3.3 V measuring terminal. TP2 (A-3) : +12 V check terminal +12 V measuring terminal. TP4 (K-6), TP5 (L-13), TP6 (H-13) : CK (clock for video) signal check terminal (DIO-62 board) Uses this terminal when checking the clock signal for video. TP7 (N-13) : VD (vertical sync) signal check terminal (DIO-62 board) VD signal measuring terminal. TP8 (P-13) : CKX (control timing) signal check terminal (DIO-62 board) CKX signal measuring terminal. TP9 (P-13) : HD (horizontal sync) signal check terminal HD signal measuring terminal. TP10 (P-13) : FLOE (field odd even) signal check terminal FLOE signal measuring terminal. TP4 (K-6), TP5 (J-13), TP6 (H-13) : CK (clock for video) signal check terminal (DIO-63 board) Uses this terminal when checking the clock signal for video. TP7 (L-12) : VD (vertical sync) signal check terminal (DIO-63 board) VD signal measuring terminal. TP8 (L-12) : CKX (control timing) signal check terminal (DIO-63 board) CKX signal measuring terminal.
TP9 (L-12) : HD (horizontal sync) signal check terminal (DIO-63 board) HD signal measuring terminal. TP10 (L-12) : FLOE (field odd even) signal check terminal (DIO-63 board) FLOE signal measuring terminal. TP100 (A-4) : +5 V check terminal (DIO-62 board) +5 V measuring terminal. TP3 (A-5) : +2.5 V check terminal +2.5 V measuring terminal. TP1000 (E-11), TP1500 (F-11) : 1R001 signal check terminal (DIO-62 board) 1R001 signal measuring terminal. TP1001 (E-11), TP1501 (F-11) : HANC signal check terminal (DIO-62 board) HANC signal measuring terminal. TP1002 (E-11), TP1502 (F-11) : LINE signal check terminal (DIO-62 board) LINE signal measuring terminal. TP1003 (E-11), TP1503 (F-11) : FRAME signal check terminal (DIO-62 board) FRAME signal measuring terminal. TP1004 (E-11), TP1504 (F-11) : CRC signal check terminal (DIO-62 board) CRC signal measuring terminal. TP1005 (E-11), TP1505 (F-11) : SIG DET signal check terminal (DIO-62 board) SIG DET signal measuring terminal. TP1006 (E-11), TP1506 (F-11) : EAV_Y signal check terminal (DIO-62 board) EAV_Y signal measuring terminal. TP1007 (E-10), TP1507 (F-10) : EAV_C signal check terminal (DIO-62 board) EAV_C signal measuring terminal. TP2000 (H-2), TP2500 (K-2), TP3000 (L-3), TP3500 (N-3), TP4000 (L-3), TP4500 (K-8), TP5000 (L-8), TP5500 (N-8) : PLL_LOCK signal check terminal (DIO-62 board) PLL_LOCK signal measuring terminal. 1-39

TP2001 (G-3), TP2501 (J-3), TP3001 (K-3), TP3501 (M-3), TP4001 (G-9), TP4501 (J-9), TP5001 (K-9), TP5501 (M-9) : EAV_Y signal check terminal EAV_Y signal measuring terminal. TP2002 (G-3), TP2502 (J-3), TP3002 (K-3), TP3502 (M-3), TP4002 (G-9), TP4502 (J-9), TP5002 (K-9), TP5502 (M-9) : EAV_C signal check terminal EAV_C signal measuring terminal. TP1000 (D-11), TP1500 (E-11), TP2000 (G-2), TP2500 (J-2), TP3000 (K-2), TP3500 (M-2), TP4000 (G-7), TP4500 (J-7), TP5000 (K-7), TP5500 (M-7) : VCO_FRQ signal check terminal (DIO-63 board) VCO_FRQ signal measuring terminal. TP1001 (E-9), TP1501 (G-9), TP2001 (H-5), TP2501 (J-5), TP3001 (L-5), TP3501 (N-9), TP4001 (H-10), TP4501 (K-10), TP5001 (L-10), TP5501 (N-9) : EAV_Y signal check terminal (DIO-63 board) EAV_Y signal measuring terminal. TP2002 (H-5), TP2502 (J-5), TP3002 (L-5), TP3502 (N-4), TP4002 (H-10), TP4502 (J-10), TP5002 (L-10), TP5502 (N-10) : EAV_C signal check terminal (DIO-63 board) EAV_C signal measuring terminal.
10. MY-102 board (MKS-8440HD/SD)
TP203 TP704 TP705 S202 D201 D202 D203 S201 D3 D2 D1 TP706

E131 E124 E132

E601 E801

TP904 TP905 TP906

TP504 TP507 E1001

TP506 TP505

<LED> D1, D2, D3 (A-6) : MY-CPU status LED Status indication of the CPU on the MY-102 board. D201 (A-5) : +12 V +12 V power supply status indication. Lit when the +12 V power is supplied. If this LED does not light, the fuse may have blown. D202 (A-5) : +3.3 V +3.3 V power supply status indication. Lit when the +3.3 V power is supplied. D203 (A-5) : +1.8 V +1.8 V power supply status indication. Lit when the +1.8 V power is supplied.
<Switch> S201 (A-5) : MY-CPU reset switch Pressing this switch initializes the CPU on the MY-102 board. S202 (A-5) : MONITOR reset switch The reset switch that is used to reset the monitor during maintenance through the terminal. <Connector> CN12 (A-8) : ISP common connector Used only for production in the assembly factory. Used for program writing into the JTAG device with ISP. CN14 (A-7) : TERMINAL pin This pin is connected to the CPU control terminal and used during maintenance. Conforms to RS-232C.
<TEST terminal> E121 (P-8), E122 (P-10), E123 (P-3), E124 (P-4), E129 (P-11), E130 (P-9), E131 (P-4), E132 (P-5), E508 (E-12), E601 (D-7), E801 (N-7), E1001 (N-12) : GND terminal Use this terminal as the earth point for measuring the respective check terminals. TP203 (C-3) : +3.3 V check terminal +3.3 V measuring terminal. TP204 (C-5) : +1.8 V check terminal +1.8 V measuring terminal. TP504 (F-2) : CKX (control timing) signal check terminal CKX signal measuring terminal. TP505 (E-12), TP706 (L-4), TP906 (L-8) : FLOE (field odd even) signal check terminal FLOE signal measuring terminal. TP506 (E-12), TP704 (L-4), TP904 (K-8) : VD (vertical sync) signal check terminal VD signal measuring terminal. TP507 (F-12), TP705 (K-4), TP905 (K-8) : HD (horizontal sync) signal check terminal HD signal measuring terminal. <LED on the CPU DR module> (C-10) Refer to < LED on the CPU DR module > in 1. CA-44 board. <Switch on the CPU DR module> (C-10) Refer to < Switch on the CPU DR module > in 1. CA-44 board.

1-8-2. Checks on the Number of Power Supply Units Setting Switch
Before turning on the power of the MVS-8000SF, confirm that the switch S303 on the CA-44 board is set in the following position (default setting when shipped from the factory). S303 (B-1)/CA-44 board : Number of power supply units setting switch (DIP type) S303-1 : OFF S303-2 : OFF S303-3 : ON S303-4 : OFF
A 1 B S303 F E D C C 3 D E
CPU-DK Module A (COM CPU-1)

B F E D C B 5

A A 1 B
CPU-DK Module (COM CPU-2)

1-9. System Connection

Configure the MVS-8000 system connections referring to the connection example as shown below. 1. Connection example

Reference video signal

Ethernet switch *a
Ethernet switch *a DATA LAN CTRL EDITOR DME Processor Pack MVE-8000
Editing Control System BVE-9100

CTRL REMOTE 1

CTRL PERIPH
REMOTE Reference video signal
System Control Unit MKS-8010

BKS-R series

HDS-X series Switcher Processor Pack MVS8000SF-C Device Control Unit Pack DCU-8000 PERIPH

Audio mixer

Crossover cable *a : Connect each LAN (CTRL, DATA) to the separate Ethernet switches respectively. BNC cable However, a single Ethernet switch can be used for connecting each LAN. *b : Terminate the system with the 75 Z terminators supplied. The 75 Z terminators are supplied with the equipment.

2. Flow of Video Signals

DME Processor Pack MVE-8000

SWITCHER B

SWITCHER A
Reference video *c signal Reference video *c signal
AC100 to 240 V Power Supply *a AC100 to 240 V Power Supply *b
DME 1B Camera VTR Routing Switcher PRIMARY INPUTS 1 to 34

DME 1A

AC100 to 240 V Power Supply *b
Switcher Processor Pack MVS8000SF-C MONITOR

OUTPUTS 1 to 16

68-pin Cable
Video Signal Input Video Signal Output Video/Key Signal AC Power Supply
*a : For the AC power cord, refer to Optional Items of the DME Processor Pack MVE-8000 Operation Manual. *b : For the AC power cord, refer to Optional Items of the Multi-Format Switcher Processor MVS-8000 Operation Manual (15 page). *c : Terminate the system with the 75 Z terminators supplied with this unit.
Section 2 Service Overview

2-1. Troubleshooting

The main power of the MVS-8000 cannot be turned on. (Indicator does not light green.)