Note : Follow the disassembly procedure in the numerical order given.
3-1. LID ASSY, UPPER, HOLDER ASSY
Note : Holder ASSY installation
1. Attach the holes on Holder ASSY to the projections on right and left sides. 2. Attach Spring (POP/L) as shown in the figure.

3 Lid ASSY , Upper

1 Screws (1.4),MI 2 Move it away from projection
Holder ASSY Reinforcement Spring (POP/L)
5 Holder ASSY 4 Move it away from projection 4 Move it away from projection

Case ASSY

3-2. MECHANISM DECK
1 Screw (MD), step Mechanism deck Motor flexible board

7 Screws, tapping (1.7)

6 OP flexible board

Reinforcement

3 Claw Case ASSY

3-3. MAIN BOARD

Note : On installation of main board, adjust the position of
both switch (S809) and knob (HOLD).

1 Screws, tapping (1.7)

Main board

Knob (HOLD)

2 Claw
3-4. OPTICAL PICK-UP ASSY
Optical pick-up ASSY (LCX-4E)

1 Washer 2 Gear (SA) 5

3 Screw (MI 1.4)

4 Spring, thrust detent

SECTION 4 TEST MODE

Lead wires: 4 leads

4-1. GENERAL
When entered in the TEST MODE, this set provides the Overall Adjustment mode which allows CD and MO discs to be automatically adjusted. In the Overall Adjustment mode, performs adjustments in sequence automatically, and displays the faulty location if any fault is found. In the Manual mode, selected adjustments can be performed automatically. Operations in the Overall Adjustment mode can be performed either via the main unit, or the keys of a remote control unit. Note that this device does not include a remote control unit. Therefore, since no connection terminals for a remote control are provided either, a connection device must be used in order to allow a suitable remote control unit to be connected. Connection Following parts are required Remote commander: RM-MZ2N (1-418-493-71) After RM-MZE1 applicable to 2.4V (Not applicable to remote commanders before RM-MZE1). Jack: 7 poles jack for phones/remote commander (1-793-288-61)
4-2. SETTING THE TEST MODE

X key : When adjusted value is changed :

+ key : Up key : Down

3. Press the PLAY MODE/DISPLAY key. CL starts to flash.
Adjusted value is written. When adjusted value is not changed : That item is adjusted automatically.
4. During each test mode, the display is changed from one to another each time DISPLAY key is pressed (Remote control only).

AdJ cL

4. Press the PLAY MODE/DISPLAY key once more. CL stops flashing and remains lit, thus concluding NV reset.
Address Value & Adjustment Value LCD display

011 XXXSXX

5. Press the x key to return to test mode.
Block Error Value & Adjustment Value LCD display

011 XX BXX

ADIP Error Value & Adjustment Value LCD display
NV reset via remote control 1. Set the TEST MODE. 2. Set the Manual mode and set the item No. 021, Reset NV. LCD display

011 XX AXX

Jitter Value & Adjustment Value LCD display * Functions are displayed, but cannot be used via this unit.

021 AAAS CC

3. Press X key on the remote control. LCD display

011 XXXJXX

Power Adjustment Value LCD display

Flash CC

731 XX VXX
After the voltage indicator appears, press the DISPLAY key twice.
4. Press X key on the remote control again. LCD display

Memory Monitor Mode

XXX: Each Value XX: Adjustment Value for Item number
5. Press x key to terminate the Manual mode and return to the TEST MODE.
Note: In the Power mode, the item title display is only displayed. 5. To terminate the Manual mode and return to the TEST MODE, press x key.
4-6-1. Electrical offset adjustment method Note: Doing adjustment by the state that a disc does not enter. 1. Confirm the power voltage is 1.5V. 2. Set to the test mode. 3. Press the key of main unit activates the overall adjustment mode. Main unit LCD display
4-7. OVERALL ADJUSTMENT MODE
4-7-1. Overall adjustment mode structure
TEST MODE (Display Check Mode) VOL key or. key
4. Press the + key. Main unit LCD display
Overall Adjustment Title Display(ASSY**)

CD overall Adjustment

> N key > N key

035: XX

5. Press the + key once more. Adjustment is complete when the adjustment value appears in the XX position. 4-6-2. Display segment check mode 1. Enter test mode. Display continuously alternates between the following three conditions: entire LCD is lit, entire LCD is extinguished, version info is shown, and so on. 2. Press and hold the x key on the main unit to enter display segment check mode. * Should segments not be displayed correctly at this point, a shortcircuited COM terminal and/or SEG terminal on the microprocessor chip (IC801) are possible causes. 3. Display returns to condition 1 as soon as the x key is released.

VOL + key

MO overall Adjustment
Electrical offset Adjustment key

PLAY MODE/DISPLAY key

NV reset
Perform overall adjustments according to the following procedures (procedures may differ depending on the microprocessor chip version used). For Ver. 1.10, if it is no good in the overall adjustment, please repeat the overall adjustment several times. Microprocessor Version 1.10

1 Clear NV.

2 Electric offset adjustment. 3 Rewriting of RAM 633h 1. switch to manual mode No. 100. 2. Press the DISPLAY key on the remote control unit 6 times consecutively to enter RAM mode. 3. Change the RAM address to 633h. Use the following keys on the remote control unit to change the digits of the RAM address: The DISPLAY key for the first digit (hundreds), the x key for the second digit (tens) and the >B key or the. key for the third digits (units). 4. Use the + and keys on the remote control unit to set the adjustment value of No.633h to 03h and press once the pause key on the remote control unit to write this value to NV. (If NV is cleared, the value is 00h.) 5. Press the DISPLAY key once more to change the display to address and adjustment value display. 6. Switch to the overall adjustment. 4 CD overall adjustment * (Not to turn off the power between the items 3 and 4.)

Ver 1.1 2001.03

5 Rewriting of the adjustment value. 1.After CD overall adjustment, switch to manual mode No. 321 in the condition the disc is in. 2.Press key on the remote control unit to set 1 step down the adjustment value of No. 321, and press the pause key on the remote control unit to write this value to NV. 3.Press the >B key on the remote control unit to switch to manual mode No. 323. 4.Press the pause key on the remote control unit to set to the automatic adjustment. During adjusting automatically, the adjustment value turns on and off, so wait for the time the adjustment value is on. 5.Press the >B key on the remote control unit to switch to manual mode No. 345. 6.Note down the current adjustment value of No. 345 (value X). Use the + and keys on the remote control unit to set the adjustment value of No. 345 to the value (Y) determined by the formula below, and press the pause key on the remote control unit to write this value to NV. Formula: X x 1.18 = Y * Since X and Y are 2sC, attention must be paid to codes. And the maximum value of Y must be 7Fh. (Never set it to the negative value.) Example: Since X = 2Bh, Y = 2Bh x 1.18 = 33h 6 Change the disc to MO overall adjustment disc (GA1 disc). Switch to manual mode No.114. Press the pause key on the remotecontrol unit to set to the automatic adjustment. After adjustment, pull out the battery from the set to turn off the power. Then insert the battery again. 7 MO overall adjustment. Microprocessor Version 1.20 and higher 1 Clear NV. 2 Electric offset adjustment. 3 CD overall adjustment. 4 Rewriting of the adjustment value. 1.After CD overall adjustment, switch to manual mode No. 321 in the condition the disc is in. 2.Press key on the remote control unit to set 1 step down the adjustment value of No. 321, and press the pause key on the remote control unit to write this value to NV. 3.Press the >B key on the remote control unit to switch to manual mode No. 323. 4.Press the pause key on the remote control unit to set to the automatic adjustment. During adjusting automatically, the adjustment value turns on and off, so wait for the time the adjustment value is on. 5.Press the >B key on the remote control unit to switch to manual mode No. 345. 6.Note down the current adjustment value of No. 345 (value X). Use the + and keys on the remote control unit to set the adjustment value of No. 345 to the value (Y) determined by the formula below, and press the pause key on the remote control unit to write this value to NV. Formula: X x 1.18 = Y * Since X and Y are 2sC, attention must be paid to codes. And the maximum value of Y must be 7Fh. (Never set it to the negative value.) Example: Since X = 2Bh, Y = 2Bh x 1.18 = 33h

2. CD overall adjustment

Item No. 300h 312h 313h 314h 571h 561h 562h 320h 323h 321h 328h 829h 323h 324h 330h 336h 337h 338h 344h 345h 521h 522h 341h 300h Description HPIT setting servo off ALFA offset adjustment IJ offset adjustment FE offset adjustment CLV start Move to inside of SLED perimeter Move to outside of SLED perimeter Focus on TE offset adjustment TE gain adjustment TWPP gain adjustment TWPP gain [LPIT] adjustment value write TE offset adjustment OFTRK adjustment Tracking ON ABCD gain adjustment KF gain adjustment RF gain adjustment FOCUS gain adjustment Tracking gain adjustment Twin axis sensitivity compensation (inside perimeter) Twin axis sensitivity compensation (outside perimeter) Field of vision oscillation check HPIT setting servo OFF

SECTION 5 DIAGRAMS

5-1. EXPLANATION OF IC TERMINALS
IC601 LC89642-8B-E (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, ATRAC ENCODER/DECODER, 8MBIT D-RAM, D/A CONVERTER) Pin No. 45 Pin name FR ISET VCVDD PDD TEST3 TEST2 SLCO SLCIST EFMIN RESETB TEST1 HFL VDD2 VSS VDD1 AVSS1 PEAK BOTTOM ABCD TE FE VC AVDD1 MAD9 DSW1 MAD8 DSW0 MAD7 SGC MAD6 AOFFSET MAD5 FOFFSET TOFFSET MAD4 TBAL LDREF FBAL VDD1 VSS VDD2 MAD3 SPPWMF SPPWMR SLPWMF I/O I I O I I O I I I I I I I I I I I O* O* O* O* O* O* O* O* O* O* O* O* O* O* O* O* O* O* O* Description Connected to Bias resistor for VTEC oscillating frequency Connected to Bias resistor for VTEC current charge pump Power supply for VTEC VTEC current charge pump output Input for test Input for test Slice level output for HF signal Connected to Bias resistor for the slice level adjusting amplifier HF signal input System reset Input for test Track detection signal input Power supply Ground Internal power supply Ground for digital servo PEAK signal input BOTTOM signal input Main beam quantity signal input Tracking error signal input Focus error signal input Center potential input Power supply for digital servo Address output to DRAM (NC) Disc mode select output Address output to DRAM (NC) Disc mode select output Address output to DRAM (NC) AGC control signal output Address output to DRAM (NC) ABCD offset control signal output Address output to DRAM (NC) Focus offset control signal output Tracking offset control signal output Address output to DRAM (NC) Tracking balance control signal output Laser control signal output Focus balance control signal output Internal power supply Ground Power supply Address output to DRAM (NC) Spindle PWM output Spindle PWM output Sled PWM output

Pin No. 94

Pin name MAD2 SLPWMR MAD1 FOPWMF MAD0 FOPWMR TRPWMF TRPWMR MAD10 AVDD OUTL OUTR AVSS VDD2 XIN XOUT VSS VDD1 F16M ENH LRCO DDATA BCO DDOUT SMON3 SMON2 SMON1 SMON0 FSEQ VP MRASBT MRASB FOK NWEB DEFECT MD1 FG CL CE MDO DI VDD1 DO VDD2 VSS MD3 WRQB INTB ADIPWO

Pin No. 62-72 73-76 77-79 80
Pin name CLV_W_CON SLED_1R_CON SLED_1F_CON SLED_2R_CON SLED_2F_CON BEEP NV_XCS RMC_DTCK SIO2_CLK SIO3_DI SIO3_DO DSP_VP VL_VCON PWR_CLK SEG0 VSS SEG1-11 COM0-3 VL1, 2, LVDD VSS
I/O O O O O O O O I/O O I O I O O O O O I
Description Spindle servo (W) drive signal output to SC111257FCR2 (IC551) Sled motor control signal output to SC111257FCR2 (IC551) Sled motor control signal output to SC111257FCR2 (IC551) Sled motor control signal output to SC111257FCR2 (IC551) Sled motor control signal output to SC111257FCR2 (IC551) Beep sound drive signal output to phones amplifier (IC301) Chip select signal output to EEPROM (IC802) TSB serial communication data input/output to/from remote commander with phones Serial clock signal output to LC89642-8B-E (IC601) and EEPROM (IC802) Read data input from LC89642-8B-E (IC601) and EEPROM (IC802) Write data output to LC89642-8B-E (IC601) and EEPROM (IC802) CLV servo lock decision signal input from LC89642-8B-E (IC601) PWM signal for VL voltage control signal to XPC18A32FCR2 (IC901) output External sync. clock (176.4kHz) signal to XPC18A32FCR2 (IC901) output LCD segment output Ground (Digital system) LCD segment output LCD common output LCD drive level power supply input Ground (Digital system)

5-2. BLOCK DIAGRAMS

Iy Ix 6 Jx

MAIN BOARD

CN501 VREF Iy
RF AMP,FOCUS/TRACKING ERROR AMP
4 VREF Iy Ix Jx Jy A B C D RF OUT PEAK /BOTM PEAK BOTM ABCD FE TE
DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, ATRAC ENCODER/DECODER, 8M BIT D-RAM, D/A CONVERTER

HEADPHONE AMP

EFMIN 17 PEAK 18 BOTTOM 19 ABCD 21 FE 20 TE AVDD ADIPWO 37 LDREF 2 RFVC MON 12 HFL VA VCVDD VDD2 VDD2 VDD2 VDD2 VOUT VIN 18 STB 17 MUTE OUT L 56 RCH OUT R 57 VD VDDVDDVDDREGULATOR UNREG VIF VC 1 +B 20 VCC 21 22
RCH 2 IN B OUT B 4 RCH LCH J301 i
Jy Jx Jy Jx A Ix Iy Ix B a bc d F C D PD
9 Ix 10 Jx 14 Jy 15 A 16 B 17 C D
RF AMP, FOCUS ERROR, TRACKING ERROR

BEEP OUT A BEEP OUT B

REFERENCE VOLTAGE SWITCHING Q301
A-C 13 D-C MON VIF 18 PD-I
1 ADIP IN 44 TPP/WPP ADIP 21 PD-NI 19

BEEP VREF IN 13

VC 31 OFTRK DVDD SERIAL I/F XRST 25 SBUS 23 SCK 24 S MON 43
DI RESET B DO 3 STATE BUFFER
5 LD-A LD LD-K 13 AVCC AVCC S0 AVCC S11 LASER AUTO POWER CONTROL Q501 PD-O S-MONITOR

Q801 EEPROM

22 VC 52 TRPWMF 53 TRPWMR 49 FOPWMF 51 FOPWMR

SYSTEM CONTROL

WRQB INTB SMON3 CE VP XIN XCLK DSP WRQB DSP INTB DSP SMON3 DSP CE DSP VP BEEP 51 HP STB 19 MUTE 18 NV XCS 52 S102 CLK 54 S102 DO 56 S102 DI 55 SEGSEGCOMCOMSLD1MON HOLD SW 15 SET KEY 4

1 XCS 2 SK 3 DI 4 DO

19 FOCUS/TRACKING COIL DRIVE, SPINDLES/SLED MOTOR DRIVE
33 PD SS BUS DATA 31 S BUS CLK 6 RF SMON
MINIDISC OPTICAL PICK-UP BLOCK (LCX-4E) 2 TRACKING COIL FOCUS COIL 3 TRK+ MINIDISC MECHANISM BLOCK M902 (SLED)

LIQUID CRYSTAL DISPLAY

OFF ON S808 (OPEN/CLOSE) S809 HOLD S807 DIGITAL MEGABASS/ AVLS DVDD 44 VD S806 S805 PLAY MODE VOLUME /DISPLAY POWER SUPPLY S804 VOLUME + VL VC VIF AVDD VG D903 LG 18 UNREG VL 9 VL 11 D902 LLVB 50 LLD901 DRY BATTERY SIZE "AA" (IEC DESIGNATION LR6) 1PC, 1.5V

35 SLD2MON

PRE DRIVER

HI-BRIDGE CONTROL BIAS

X801 16.9344MHz

OPEN CLS SW XIN 16 XOUT

S802 >N

S801 x

VLO 10 VCO 35 VIF 42 VA 41 VG XWKXWK1

HI-BRIDGE CONTROL

RMC KEY 3
CN551 SLED1+ SLEDPRE DRIVER HI-BRIDGE CONTROL SLED 1R CON 48 SLED 1F CON 37 SLD VCON

UNREG MON 1

VRMC XWK3 VSTB XWK2
VC VCOM 38 VL VCOM 58 PWR CLK PWR VLON PWR SLEEP PWR FFCLR XRST AVDD VL MON 8
26 INMRFRF34 INM2 CLK VLON SLEEP FFCLR XRST VC VC 45 VC2

SLED2+ 6 SLED2- 8

50 SLED 2F CON 49 SLED 2R CON XCS NV SICLV U MON SCKCLV V MON SCLV W MON
M901 (SPINDLE) CLVU CLVV CLVW 4 UNREG
PRE DRIVER 3 PHASE CONTROL

PWR CLKSEL 30

52 CLK SEL VC OUT 33
46 CLV W CON 45 CLV V CON 44 CLV U CON 36 CLV VCON

BP801 (TEST) XADJUST 14

Signal path. F : Analog J : Digital

5-3. PRINTED WIRING BOARDS MAIN SECTION (1/2)
Refer to page 24 for Notes.
DRY BATTERY SIZE "AA" (IEC DESIGNATION LR6) 1PC, 1.5V A

Semiconductor Location

Ref. No. Location C-9 C-9 A-2 C-6 F-3 C-8 D-8 F-9 D101 D351 D903

MAIN BOARD (SIDE B)

TP924 TP912

R615 C616

C608 C607

TP954 TP616 C620 CTP617

C614 R95 75

TP618 TP612 TP611 TP610

IC501 IC551 IC601 IC801 Q801
TP908 TP909 TP910 TP917 TP920 TP911

R607 C601 C517

TP904 TP907

TP570 TP571 TP1

TAP501 C509 TP527

TP572 TP573

S808 (OPEN/CLOSE)
TAP502 TP806 D101 TP302 TP103

C M902 SLED MOTOR 6

CN501 TP506 1

MOTOR FLEXIBLE BOARD

TP507 5

1-679-187-11

TP504 C25 23
OPTICAL PICK-UP BLOCK LCX-4E

TPTP817 TP575TP574

R804 R805

R808 R807 R806

TP61 TPTP812

M901 SPINDLE MOTOR

TP807 TP810 TP814

C803 C805 R821

BP801 (TEST) C806 TP809 TP808 R907

Q801 BCE 11 (11)

1-679-460-
5-4. PRINTED WIRING BOARDS MAIN SECTION (2/2)
Ref. No. Location E-1 B-7 B-8 B-2 C-2 E-2 F-2 B-7 D-1 E-5 D201 D901 D902

TP803 TP802 L905 TP804

R204 C203

C103 R104

TP805 TP806 TP30

L902 C953

C905 R909

R203 R603 R903 C902

C909 C901
C204 R202 R201 R101 R102 C104
IC301 IC602 IC802 IC803 IC901 Q301 Q501

56 C915

L904 C903

C610 C617

C605 C604

C913 R901

C304 C B E C301

C351 R303

J301 i

R946 R948

S804 VOL+ R814
LCD801 LIQUID CRYSTAL DISPLAY

S805 VOL C529 C524

R815 RB552 S806 PLAY MODE
RB553 S807 DIGITAL MEGABASS AVLS(2SEC)

C558 C557

Q501 L502 S809 HOLD. OFFtON

CF 1 R824

DISPLAY(2SEC) RB551

42 C917 R947 R936

11 (11)
5-5. SCHEMATIC DIAGRAM MAIN SECTION (1/3)
Refer to page for IC Block Diagrams.
Refer to page 25 for Waveforms.

IC B/D

5-6. SCHEMATIC DIAGRAM MAIN SECTION (2/3)

IC B/D IC B/D

5-7. SCHEMATIC DIAGRAM MAIN SECTION (3/3)
Note on Printed Wiring Boards: MAIN SECTION X : parts extracted from the component side. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from the (Side B) pattern face are indicated. Parts face side: Parts on the parts face side seen from the (Side A) parts face are indicated.

Note on Schematic Diagram: MAIN SECTION All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. : B+ Line. Power voltage is dc 1.5V and fed with regulated dc power supply from battery terminal. Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : PLAY Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : Analog J : Digital

Waveforms

1 IC(TE), IC601 w; (TE) (PLAY Mode) 200 mV/DIV, 1 s/DIV 5 IC601 y; (XIN) 400 mV/DIV, 20 ns/DIV 9 IC551 ta, ts, td, tf (COM, CPWI, CPVI, CPUI) 400 mV/DIV, 5 s/DIV

Approx. 396 mVp-p

1.1 Vp-p

16.34MHZ

11.5 s
2 IC501 8, 9, 0, qa (IY, IX, JX,JY) (PLAY Mode) 200 mV/DIV, 500 ns/DIV 6 IC(PWM), IC801 eh (CLV V CON) (PLAY Mode) 1 V/DIV, 2 s/DIV 0 IC801 qh (XOUT) 1 V/DIV, 20 ns/DIV

Approx. 540 mVp-p

2.2 Vp-p

3 Vp-p

16.934MHz
3 IC501 ed (RF), IC(EFMIN) (PLAY Mode) 400 mV/DIV, 1 s/DIV 7 IC551 2, 3, 4 IC801 rf, rg, rh (CLV U CON, CLV V CON, CLV W CON) (PLAY Mode) 1 V/DIV, 5 ms/DIV qa IC901 th (CLK) 1 V/DIV, 2 s/DIV

Approx. 1.1 Vp-p

2.8 Vp-p

5.76 s

11.1 ms
4 IC501 rs (FE), IC601 wa (FE) (PLAY Mode) 200 mV/DIV, 1 s/DIV 8 IC551 1, tg, th (CPUO, CPWO, CPVO) IC801 el, rs, rd (CLV U MON, CLV V MON, CLV W MON) 1 V/DIV, 5 ms/DIV

Approx. 416 mVp-p

11.8 ms
IC BLOCK DIAGRAMS IC301 TA2131FL-EL
BST SW BEEP IN VREF IN 13 V REF 12 VREF 11 LPF1 TC MT 19 VCC 20 INR 21 BST1 INL LPF2 ADD 10 BST NF1 MUTE GND 14 BST2 STB 18 PW SW

6-1. MAIN SECTION

not supplied

LCD801

Ref. No. 6 6

Part No.

Remark

Ref. No. * * 15 16

Part No. 4-218-233-25 3-375-114-41 3-226-522-01 4-223-906-01 A-3323-668-A 1-694-743-11 3-226-523-01 X-3380-004-1 3-226-518-01 3-226-520-01
Description SCREW (1.4), MI SCREW, TAPPING (1.7) SPRING (POP/L) SCREW (MD), STEP MAIN BOARD, COMPLETE CONDUCTIVE BOARD, CONNECTION HOLDER, LCD PLATE ASSY, FULCRUM BUTTON (CONTROL) SPRING, TERMINAL COIL
X-3380-002-1 CASE ASSY (S).(SILVER) (CND,AEP,FR,EE,E,CH) X-3380-005-1 CASE ASSY (L).(BLUE) 4-225-572-03 KNOB (HOLD).(SILVER) (CND,AEP,FR,EE,E,CH) 4-225-572-11 KNOB (HOLD).(BLUE) 3-226-517-01 WINDOW (LCD) 3-226-512-01 LID, BATTERY CASE.(SILVER) (CND,AEP,FR,EE,E,CH) 3-226-512-11 LID, BATTERY CASE.(BLUE) X-3379-511-1 HOLDER ASSY X-3380-003-1 LID ASSY (S), UPPER.(SILVER) (CND,AEP,FR,EE,E,CH) X-3380-006-1 LID ASSY (L), UPPER.(BLUE)
17 3-226-519-01 TERMINAL (PLUS), BATTERY 18 3-229-530-01 SHEET, SHIELD LCD801 1-804-162-11 DISPLAY PANEL, LIQUID CRYSTAL
6-2. MECHANISM DECK SECTION (MT-MZE300-176)

M902 M901

Ref. No. 59
Part No. 1-679-187-11 3-222-392-01 3-223-833-01 3-224-779-01 4-222-216-01 3-338-645-51 4-218-233-13 4-218-233-01 4-222-208-01
Description MOTOR FLEXIBLE BOARD SCREW (M1.4), TAPPING CHASSIS SPRING, THRUST DETENT GEAR (SA) WASHER SCREW (1.7), MI SCREW (1.4), MI GEAR (SB)

Ref. No. 65 M901 M902

Part No. 4-222-204-01 4-222-203-01 X-3379-869-1 3-222-391-01 3-225-278-11
Description BEARING (N) SCREW, LEAD OPTICAL PICK-UP ASSY (LCX-4E) SPRING (M), RACK SCREW, TAPPING
X-3379-529-1 BASE ASSY, MOTOR 8-835-706-01 MOTOR, DC SSM18A (SPINDLE) 1-763-399-11 MOTOR, DC (SLED) (INCLUDING PULLEY GEAR)

MZ-E300 MAIN

NOTE : Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX, -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms METAL : Metal-film resistor METAL OXIDE :Metal oxide-film resistor F : nonflammable Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Ref. No. * Part No. Description
SECTION 7 ELECTRICAL PARTS LIST
SEMICONDUCTORS In each case, u : , for example : uA. : A. , uPA. : PA. uPB. : PB. , uPC. : PC. uPD. : PD. CAPACITORS uF : F COILS uH : H Abbreviation CND : Canadian FR : French EE : East European CH : Chinese The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi. When indicating parts by reference number, please include the board.

Ref. No. C553 C554 C555 C556 C557 C558 C559 C561 C601 C602 C603 C604 C605 C606 C607 C608 C609 C610 C611 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C801 C802 C803 C804 C805 C806 C807 C808 C810 C811 C813 C851 C901 C902
Part No. 1-135-211-11 1-135-211-11 1-107-826-11 1-107-826-11 1-110-563-11 1-110-563-11 1-110-563-11 1-164-156-11 1-164-156-11 1-107-826-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-135-259-11 1-135-259-11 1-164-156-11 1-164-156-11 1-164-227-11 1-107-826-11 1-107-826-11 1-107-826-11 1-164-156-11 1-164-156-11 1-162-969-11 1-164-156-11 1-164-156-11 1-131-862-91 1-131-862-91 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-165-176-11 1-165-176-11 1-162-962-11 1-164-156-11 1-162-964-11 1-162-970-11 1-164-156-11
Description TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 6.8uF 6.8uF 0.1uF 0.1uF 0.068uF 0.068uF 0.068uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF 0.1uF 0.1uF 0.022uF 0.1uF 20% 20% 10% 10% 10% 10% 10%
Remark 6.3V 6.3V 16V 16V 16V 16V 16V 25V 25V 16V 25V 25V 25V 25V 6.3V 6.3V 25V 25V 25V 16V 16V 16V 25V 25V 25V 25V 25V 4V 4V 25V 25V 25V 25V 16V 16V 50V 25V 50V 25V 25V 25V 6.3V 4V
A-3323-668-A MAIN BOARD, COMPLETE ********************* 1-694-743-11 CONDUCTIVE BOARD, CONNECTION 3-226-523-01 HOLDER, LCD 3-229-530-01 SHEET, SHIELD < CAPACITOR > C101 C102 C103 C104 C201 C202 C203 C204 C301 C302 C303 C304 C305 C306 C351 C501 C502 C503 C504 C505 C508 C509 C510 C511 C513 C515 C516 C517 C519 C524 C527 C529 C530 C551 C552 1-109-982-11 1-119-944-22 1-115-467-11 1-162-962-11 1-109-982-11 1-119-944-22 1-115-467-11 1-162-962-11 1-135-259-11 1-164-156-11 1-109-982-11 1-135-210-11 1-125-838-11 1-104-847-11 1-164-156-11 1-162-964-11 1-164-677-11 1-162-967-11 1-162-967-11 1-162-970-11 1-162-965-11 1-162-967-11 1-162-915-11 1-162-919-11 1-162-915-11 1-164-156-11 1-107-826-11 1-162-970-11 1-162-968-11 1-117-920-11 1-165-176-11 1-117-920-11 1-162-966-11 1-104-912-11 1-104-912-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP 1uF 470uF 0.22uF 470PF 1uF 470uF 0.22uF 470PF 10uF 0.1uF 1uF 4.7uF 2.2uF 22uF 0.1uF 0.001uF 0.033uF 0.0033uF 0.0033uF 0.01uF 0.0015uF 0.0033uF 10PF 22PF 10PF 0.1uF 0.1uF 0.01uF 0.0047uF 10uF 0.047uF 10uF 0.0022uF 3.3uF 3.3uF 10% 20% 10% 10% 10% 20% 10% 10% 20% 10V 4V 10V 50V 10V 4V 10V 50V 6.3V 25V 10V 10V 6.3V 4V 25V 50V 16V 50V 50V 25V 50V 50V 50V 50V 50V 25V 16V 25V 50V 6.3V 16V 6.3V 50V 6.3V 6.3V

1-164-156-11 CERAMIC CHIP < CONNECTOR >

* CN501 * CN551

1-778-168-11 CONNECTOR, FFC/FPC (ZIF) 20P 1-815-284-21 CONNECTOR, FPC (ZIF) 8P < DIODE >
D101 D201 D351 D901 D902 D903
8-719-056-72 8-719-056-72 8-719-017-58 8-719-081-33 8-719-081-33
DIODE DIODE DIODE DIODE DIODE
UDZ-TE-17-2.4B UDZ-TE-17-2.4B MA8068 MA2YD1500LS0 MA2YD1500LS0
8-719-049-09 DIODE 1SS367-T3SONY < FERRITE BEAD >
0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
1-414-226-21 FERRITE < IC >
IC301 IC501 IC551 IC601 IC602 IC801 IC802 IC803 IC901
8-759-598-15 8-759-689-67 8-759-698-62 8-759-697-82 8-759-834-07 6-700-663-01 8-759-468-72 8-759-592-49 8-759-698-61
IC IC IC IC IC IC IC IC IC
TA2131FL(EL) SN761057DBT SC111257FCR2 LC89642-8B-E XC62FP2302MR RU6615MF-0005 AK6420AM-E2 TC7SZ125FU(TE85R) XPC18A32FCR2
< JACK > J301 1-794-084-31 JACK < COIL > L502 L551 L552 L553 L554 L901 L902 1-469-570-21 1-410-389-31 1-410-389-31 1-414-400-41 1-414-400-41 INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR 10uH 47uH 47uH 22uH 22uH 68uH 47uH
1-419-258-21 INDUCTOR 1-419-646-21 INDUCTOR
Ref. No. R822 R824 R826 R827 R830 R901 R903 R905 R906 R907 R909 R910 R912 R936 R946 R947 R948 R949 R951 Part No. 1-216-821-11 1-216-845-11 1-216-864-91 1-216-857-11 1-216-833-11 1-218-871-11 1-216-825-11 1-216-825-11 1-216-847-11 1-216-833-11 1-216-827-11 1-216-827-11 1-218-907-11 1-218-744-11 1-218-895-11 1-218-911-11 1-218-907-11 1-218-911-11 1-216-864-91 Description METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT 1K 100K 0 1M 10K 10K 2.2K 2.2K 150K 10K 3.3K 3.3K 330K 150K 100K 470K 330K 470K 0 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% Remark 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W LCD801 M901 M902 1-694-743-11 1-679-187-11 X-3379-869-1 1-804-162-11 8-835-706-01 1-763-399-11 Ref. No. Part No. Description MISCELLANEOUS *************** CONDUCTIVE BOARD, CONNECTION MOTOR FLEXIBLE BOARD OPTICAL PICK-UP ASSY (CLX-4E) DISPLAY PANEL, LIQUID CRYSTAL MOTOR, DC SSM18A (SPINDLE) MOTOR, DC (SLED) (INCLUDING PULLEY GEAR) ************************************************************** ACCESSORIES & PACKING MATERIALS ******************************** 3-021-018-11 LABEL, FRANCE (FR) 3-224-084-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,SPANISH,PORTUGUESE) (US,CND,AEP,FR,E) 3-224-084-21 MANUAL, INSTRUCTION (GERMAN,ITALIAN,DUTCH,SWEDISH) (AEP) 3-224-084-31 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN,HUNGARIAN, CZECH,FINNISH) (AEP,EE) 3-224-084-41 MANUAL, INSTRUCTION (ENGLISH,SIMPLIFIED CHINESE, POLISH,SLOVAK) (EE,CH) 3-224-084-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE,KOREAN) (E) 8-953-301-92 RECEIVER,EAR MDR-E805LP (CND,AEP,FR,EE,E,CH) 8-953-775-95 HEAD SET MDR-026LP (US) Remark

< COMPOSITION CIRCUIT BLOCK > RB551 RB552 RB553 1-233-959-21 RES, NETWORK (CHIP TYPE) 470 1-233-979-11 RES, NETWORK (CHIP TYPE) 1M 1-233-967-11 RES, NETWORK (CHIP TYPE) 10K < SWITCH > S801 S802 S803 S804 S805 S806 S807 S808 S809 1-786-033-21 1-786-033-21 1-786-033-21 1-786-033-21 1-786-033-21 SWITCH, TACTILE (x) SWITCH, TACTILE (> N) SWITCH, TACTILE (.) SWITCH, TACTILE (VOL+) SWITCH, TACTILE (VOL)
1-786-033-21 SWITCH, TACTILE (PLAY MODE/DISPLAY(2SEC)) 1-786-033-21 SWITCH, TACTILE (DIGITAL MEGABASS/AVLS(2SEC)) 1-786-061-21 SWITCH, PUSH (1 KEY) (OPEN/CLOSE) 1-762-078-11 SWITCH, SLIDE (HOLD.) < VIBRATOR >
X801 1-781-575-21 VIBRATOR, CERAMIC (16.9344MHz) **************************************************************
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

REVISION HISTORY

Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.2 1.1 1.0 Date 2001.12 2001.03 2001.02 Description of Revision Change of microprocessor (IC801 : Ver 1.3). Correction of Overall Adjustment Mode. Correction of Electrical Parts List. New

(SPM-01052)