Capital City Computing, LLC
Service Manual for Sony Vaio PCG 7X2L
Tools Needed - small screw driver - small flat head screw driver or letter opener How to remove and replace the hard disk drive (HDD) NOTE: I replaced a TOSHIBA MK8034GSX 80GB 5400 RPM 8MB Cache 2.5" SATA 1.5Gb/s Notebook Hard Drive with a Seagate Momentus 7200.4 ST9500420AS 500GB 7200 RPM 16MB Cache 2.5" SATA 3.0Gb/s Internal Notebook Hard Drive. 1. Disconnect power and remove battery.
2. Turn the laptop over and remove all the screws on the bottom.
3. Remove the memory cover.
4. Remove the screw underneath the memory cover. 5. Remove the DVD drive.
6. Remove the 3 black screws underneath the DVD drive. Note the size of the screws. 7. Remove the 3 screws underneath the battery cover. Note the size of the screws. 8. Remove keyboard by using letter opener to press in 5 plastic tabs at bottom of keys. Work your way from right to left.
9. When you press in plastic tabs, carefully lift up on front black edge of keyboard. 10. Repeat step 9 for each plastic tab. 11. Remove keyboard ribbon cable by carefully sliding and lifting up on the black part of the black and white connector. The black ribbon cable will easily slide free from the connector
12. Remove the screw underneath the keyboard. Note the size of the screw. This screw is longer than the other screws.
13. Remove the mouse touchpad ribbon cable by lifting up on the black part of the black and white connector. Pull the blue tab on the ribbon cable. 14. Use blade of letter opener to carefully pry adjoined plastic cover open. I found that if you start by the DVD player, it is easier to pry open and make your way around the edge of laptop.
15. Remove the two black screws that are holding the HDD case to the motherboard.
16. Carefully slide the enclosed HDD lose from the SATA motherboard connector. NOTE: The HDD is located in the silver case located underneath the left palm rest or on the left front side of the laptop. 17. Remove the four screws from the side of the HDD. 18. Perform imaging of the existing old HDD to the new HDD. I used a SATA to USB connector and Acronis True Image to copy the data.
19. Insert the four screws into the side of the HDD. 20. Repeat the steps in reverse order.

PCG-FXA53/FXA59

SERVICE MANUAL

Ver 2-2002G

For American Area

US Model CanadianModel

Revision History
Lineup : PCG-FXA59 PCG-FXA53

de fi n

al ti n
Design and specifications are subject to change without notice.

NOTEBOOK COMPUTER

9-874-549-02
Information in this document is subject to change without notice. Sony, VAIO and CLIE are trademarks or registered trademarks of Sony. Microsoft, Windows, Windows Media, Outlook, Bookshelf and other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the United States and other countries. The word Bluetooth and the Bluetooth logo are trademarks of Bluetooth SIG, Inc. AMD, AMD logo, AMD Duron and combinations thereof, 3DNow!, are trademarks of Advanced Micro Devices, Inc. Intel Inside logo, Pentium and Celeron are trademarks or registered trademarks of Intel Corporation. Transmeta, the Transmeta logo, Crusoe Processor, the Crusoe logo and combinations thereof are trademarks of Transmeta Corporation in the USA and other countries. Graffiti, HotSync, PalmModem, and Palm OS are resistered trademarks, and the Hotsync logo and Palm are trademarks of Palm, Inc. or its subsidiaries. (M) and Motrola are trademarks of Motrora, Inc. Other Motrola products and services with (R) mark like Dragomball are the trademarks of Motrola, Inc. All other names of systems, products and services in this manual are trademarks or registered trademarks of their respective owners. In this manual, the (TM) or (R) mark are not specified.
Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the operating and the service instructions. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions. CAUTION: The battery pack used in this device may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100C (212F) or incinerate. Dispose of used battery promptly. Keep away from children. CAUTION: Changing the back up battery. Overcharging, short circuiting, reverse charging, multilation or incineration of the cells must be avoided to prevent one or more of the following occurrences; release of toxic materials, release of hydrogen and/or oxygen gas, rise in surface temperature. If a cell has leaked or vented, it should be replaced immediately while avoiding to touch it without any protection.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas requiring special precautions. Be sure to observe these precautions, as well as all precautions listed in the operating manual and other associated documents.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring have been returned to their original condition. Also check the area around the repair location to ensure that repair work has caused no damage, and confirm safety.
2. Use designated parts only
The sets components possess important safety characteristics, such as noncombustibility and the ability to tolerate large voltages. Be sure that replacement parts possess the same safety characteristics as the originals. Also remember that the 0 mark, which appears in circuit diagrams and parts lists, denotes components that have particularly important safety functions; be extra sure to use only the designated components.

5. When replacing chip components.
Never reuse components. Also remember that the negative side of tantalum capacitors is easily damaged by heat.
6. When handling flexible print boards.
The temperature of the soldering-iron tip should be about 270C. Do not apply the tip more than three times to the same pattern. Handle patterns with care; never apply force.
3. Always follow the original design when mounting parts and routing wires
The original layout includes various safety features, such as inclusion of insulating materials (tubes and tape) and the mounting of parts above the printer board. In addition, internal wiring has been routed and clamped so as to keep it away from hot or high-voltage parts. When mounting parts or routing wires, therefore, be sure to duplicate the original layout.
Caution: Remember that hard disk drives are easily damaged by vibration. Always handle with care.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

Confidential 2

PCG-FXA53/FXA59 (AM)

TABLE OF CONTENTS

Section Title Page
CHAPTER 1. BLOCK DIAGRAM. 1-1

(to 1-2)

CHAPTER 2. FRAME HARNESS DIAGRAM. 1-1
CHAPTER 3. EXPLODED VIEWS AND PARTS LIST.. 3-1
3-1. Main Section... 3-2 3-2. FDD Section... 3-5 3-3. LCD Section (FXA53 Model) Made by AC . 3-7 3-3-A. LCD Section (FXA59 Model) Made by SH . 3-8(a) 3-4. Connector Section (CH Type Only).. 3-9 (to 3-10)

CHAPTER 4. OTHERS

4-1. Replacing the CPU... 4-1 1. Removing the CPU... 4-1 2. Installing the CPU.. 4-1
History of the changes is shown as the Revision History at the end of this data.

Confidential 3

CHAPTER 1. BLOCK DIAGRAM
CPU AMD Mobile Athlon XP 1500 + (Cache:128KB L1 256KB L2) (FSB 200 MHz) 462 PIN PGA SOCKET A

PCG-FX Series

BLOCK DIAGRAM Rev.A

LCD Panel PC Card

Socket 1
w/ Port Replicator (PCGA-PRFX1)

PC Card

Socket V IN

2001/08/27

14.1" TFT Main Memory
PC133 SO-DIMM 256MB X1 (Max.512MB) ADDRESS SIGNAL CTRL DATA XGA

Port Replicator

CNX-126
LCD Sig SO-DIMM Slot A SO-DIMM Slot B D RAM SIG NAL

Card bus Signal

POWER CIRCUIT CPU-VCC MAXIM 1711 CORE

VA 1 DC-IN

North Bridge VIA KT133A VT8363A
Graphic ATI 3D RAGE Mobility-M1

TV Sig

NTSC/PAL

TV out

CARD BUS
TI PCI1420 5V/5 VSUS MAXIM 1632A 3V/3 VSUS 2 RJ-45

CPU CLOCK

CLK GEN

ICS9248BF-168

PCI CLOCK USB CLOCK 14M CLOCK

Main System Board MBX-61

PCI BUS 3 VGA

10 AC LINK 4

Serial DSUB-9

i.LINK

USB USB P0 USB P1 USB P2 USB P3 TI TSB12LV26

PHY TI TSB41LV01

Realtec RTL8139CL CN 30-pin 108-pin Port Replicator CONNECTOR 108-pin Port Replicator CONNECTOR

AC97 AD1881A DAA

Amp TPA0132

Headphone

Mini PCI MDC

LAN RJ-45

SOUTH BRIDGE

VIA VT82C686-B

AC LINK COM SIGNAL

Primary IDE Bus

5 MAXExt. MIC

Parallel DSUB-25

Optical Devices

Secondary IDE Bus

Parallel D SUB-25

PS/2 MDIN-6

5 ISA 7 KBD USB 1

PCU NS KBC

BIOS Flash 4M bit 9 VA 1 V IN Touch 12 Pad CN

18-pin

8 PS/2 6

PC 87570

10-pin

60-pin SP_L

BATTERY 0

T/P BOARD CNX-129

BATTERY 1

DC/DC BOARD PWS-14

Serial D SUB-9
POWER SWITCH BOARD SWX-74

I/O SUB BOARD CNX-150

Confidential
1-1 1-2 (END) PCG-FXA53/FXA59 (AM)
CHAPTER 2. FRAME HARNESS DIAGRAM
DC-IN USB NETWORK MONITOR PRINTER SERIAL USB PHONE

Rear Panel

KEY BOARD INVERTER DC FAN FFC LED

CON15 CON19

VIDEO OUT EXTERNAL MICROPHONE HEADPHONE IEEE 1394 i.LINK
CON5 CPU1 CON18 CON17 CON8

2 CON23

CON21 1

CON1 CON3

CNX-150 Board (Side-A)

143 144

1 CON12 29

MBX-61 Board (Side-A)

CARD MODEM

HARD DISK

PC CARD CONNECTOR

Speaker L

Speaker R

76 CON7

CON3 49

SWX-74 (Side-A)

COMBO DRIVE

RAM OPTION

RAM PC133 SO-DIMM 256MB

FLOPPY DISK DRIVE

BATTERY PACK

PWS-14 Board (Side-B)

CNX-129 Board (Side-B)
2nd BATTERY PACK (OPTION)
From board to connector (direct connection) Harness (connector at both end) Harness (soldered at one end) Connectors soldered on board and appearing on the panel

TOUCH PAD

2-1 2-2 (END) PCG-FXA53/FXA59 (AM)
CHAPTER 3. EXPLODED VIEWS AND PARTS LIST
The mechanical parts with no reference number in the exploded views are not supplied. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. When two or more parts are shown in parallel, use the part described first as the main part. The indication [CH] is used for identification of part type. Regarding the boards of this model, the discrete parts on the boards cannot be replaced. However, Some connectors can be replaced.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

3-1 PCG-FXA53/FXA59 (AM)

3-1. Main Section
Ref.No. ** 29 * * * 57 * 58 * * 74 * 76 * 125 * 157 Part No. X-4623-848-3 4-640-837-22 4-651-706-01 4-656-752-01 4-643-832-21 A-8049-276-A X-4623-389-1 1-529-287-11 1-790-639-22 A-8059-429-A 1-476-647-12 X-4623-849-3 1-772-529-72 A-8049-275-A 4-651-699-01 4-651-708-12 4-640-861-04 1-796-264-11 X-4623-436-2 4-640-860-03 4-656-727-01 4-656-735-01 4-651-714-01 4-656-736-01 A-8049-270-A 1-761-380-23 1-790-640-11 4-640-845-11 4-644-349-01 4-640-854-01 4-651-850-01 4-640-857-01 4-651-698-01 4-651-928-02 4-656-756-01 4-641-851-02 4-657-283-01 4-651-702-01 4-644-361-01 4-644-362-11 Description [CH].ASSY BOTTOM (Q) DOOR BATTERY HEATSINK BOTTOM [CH].INSULATOR HEATSINK BOTTOM DUMMY CARD COMPLETE PWB SWX-74 ASSY HOOD KEYBOARD Z (P) SPEAKER UNIT FPC 50PIN (FOR HDD) ASSY HDD 30GB (H,20,F) (S) KEY BOARD UNIT (US) [CH].ASSY PALMREST (Q) PAD, TOUCH COMPLETE PWB CNX-129 BRACKET PAD BRACKET (HDD) BRACKET CD-ROM R COMBO DRIVE (UJDA720) ASSY DOOR DVD-RW (PA) BRACKET (CD-ROM L) [CH].DOOR I/O [CH].FOOT REAR DOOR DOCKING CONNECTOR [CH].FOOT FRONT COMPLETE PWB PWS-14 CARD, MODEM FPC 50PIN (FOR CD-ROM) BUTTON BAY LATCH BAY SPRING BAY BRACKET BOTTOM DOOR BATTERY SPRING DISPLAY BASE COVER BATTERY CONNECTOR [CH].LABEL I/O SPRING (FDD), PLATE [CH].BRACKET IO DOOR DIMM BRACKET SPK PLATE PALMREST Ref.No. 180 * B1 B3 B4 B7 B8 B10 B12 B14 B15 B17 B31 B32 B33 BPart No. 4-654-019-01 4-654-047-01 4-653-936-01 A-8059-275-A 4-644-667-01 4-654-631-01 4-663-824-01 4-654-398-01 4-657-164-03 4-655-511-01 4-654-776-01 4-654-783-01 4-655-042-01 4-658-711-01 4-658-542-01 4-657-629-01 4-657-049-01 4-658-470-01 4-659-640-01 4-659-641-01 Description GASKET (AV) SHIELD (AV) GASKET (HB/M) COOLING UNIT-3 COVER RJ-11 GUARD SPK TAPE CPU (A-XP) PLATE GROUND (SH) BRACKET WIRE 2 GASCKET (DRIVE) INSULATOR (SCREW) SHIELD TAPE (HDD) SHIELD SHEET (FAN) SHIELD TAPE (FAN)2 SPACER (KEY BOARD) SPRING DRIVE (PA) SPRING DRIVE (PA-R) [CH].GASKET (DOCK) TAPE (DOCK) J SHIELD TAPE (USB) 2J

9-885-020-01 CABLE ASSY (RJ-45-CONN) 4-653-151-01 SPACER (KBF) 4-664-390-01 TAPE M/B J 4-641-726-41 4-644-899-01 4-639-112-01 4-644-402-12 4-641-726-11 4-652-498-01 4-645-177-01 4-645-497-01 4-635-301-01 7-622-205-05 4-645-214-11 7-621-772-68 4-642-852-21 4-651-989-01 SCREW SCREW SCREW SCREW SCREW (M2), SPECIAL HEAD (M2), 0 NUMBER P3 KIND M2X4 (MBX) (M2), SPECIAL HEAD
+B M2 (NOJI) SCREW (M1.7X3.5) SCREW (M2.6), CROSS (HOLE) BIND SCREW M3X4 NUT M2 TYPE2 GRIP, M2 SCREW +B 2X12 +B M2 SPACER (MBX) Refer to section 3-2.FDD Section
6-600-118-01 IC MT8LSDT3264HG-133B1 (PC-133 SO-DIMM (256MB CL3)) 6-600-114-01 IC HYS64V32220GDL-7.5-C2 (PC-133 SO-DIMM (256MB CL3)) 1-960-827-21 HARNESS (2 PIN) A-8110-217-A MAIN BOARD ASSY 4-641-630-11 COVER BAY HOLE 1-790-711-21 1-757-767-11 1-790-710-11 4-645-433-01 4-644-357-01 6-702-541-01 X-4623-561-2 1-756-148-11 4-651-701-01 4-654-701-01 FFC (PPK) FFC (TP-CNX) FFC (SWX-PWS) BRACKET BAY CONNECTOR CUSHION SPK IC AXMS1500FWS3B (Athlon XP 1500+) ASSY LATCH DETECTOR SECONDARY BATTERY, LITHIUM DOOR MODEM CUSHION (HD-M2)

NOTE :

When replacing the CPU, refer to 4-1. Replacing the CPU.

3-2 PCG-FXA53/FXA59 (AM)

B8 B1 B33 B186 N B15 K B1 BBB63 B8 H BL BL C 72 BBE B31 B3 A 11 B Supplied with 8 B3 B74 BB701 (Refer to Page 3-8.) F D E B(Refer to Page 3-5.) 162 B8 B B163 B190 B33 BD Supplied with B8 BBBM I K Supplied with 88 B8 Supplied with 88 Supplied with 19 B18 H 136 BB162 B4 BC B26 M 60 B185 BB32 A N 25 J B1 BI J
3-3 3-4 PCG-FXA53/FXA59 (AM)

3-2. FDD Section

How to use properly the FDD repair parts.
Types of service to be provided are different depending on the part No. of the FDD in use. Label FD
X-XXX-XXX-XX Label Part No.
The service types are shown below depending on the part No. that is printed in the bottom right of the FD label. [Label Part No. : 4-656-805-0*]
[Label Part No. : 4-641-763-3*]

800 806

802 B1

803 B1

Ref.No. Part No. Description 800 A-8025-674-A FDD UNIT ASSY (TN-CH)

Ref.No. B1

Part No. A-8048-966-A 4-640-828-01 1-796-231-11 X-4623-835-1 1-790-641-11 4-641-629-01
Description ASSY BAY FD (TE) PLATE FDD FDD (FD-07-7760) ASSY BOTTOM FDD Z (TCY3) FPC 50PIN (FOR FDD) INSULATOR FDD
4-641-763-31 LABEL FD 4-644-053-01 SPACER FDD 4-646-807-PLATE M2.5 (FDD)
3-5 3-6 PCG-FXA53/FXA59 (AM)
3-3. LCD Section (FXA53 Model) Made by AU

B8 B305

Ref.No. * 322
Part No. 1-476-318-21 X-4623-378-1 X-4623-409-3 4-635-277-22 4-635-276-22 4-637-902-31 A-8023-466-A 4-637-903-01 X-4623-379-1 X-4623-458-1 4-642-762-31 4-664-249-11 1-757-605-11 4-654-966-01 4-644-163-11 4-644-164-11 4-642-760-12 1-961-018-81 4-650-831-01 4-645-219-01
Description INVERTER UNIT HINGE LEFT MV ASSY HOU, BEZEL 14SA-Z COVER SCREW LOWER COVER SCREW UPPER LATCH ASSY LCD XGA 14AU (S) SPRING LATCH HINGE RIGHT MV ASSY HOU, DISPLAY 14FV-Z COVER HINGE (15) LABEL ID (U) PWB, FLEXIBLE PRINT (SINGLE) SHEET (BEZEL), ADHESIVE BRACKET LCD LEFT 14 (SA) BRACKET LCD RIGHT 14 (SA) CUSHION CENTER HARNESS, LCD (XGA-F-N) SHIELD TAPE (SK) LCD TAPE 13.3

Ref.No. Part No.

Description ACCESSORIES ************
A-8048-965-A ASSY WEIGHT SAVER (Z) (Refer to Page 3-4.) 1-476-342-41 ADAPTOR, AC A-8110-712-A BP71A SNT (U) ASSY (S) 1-575-875-51 CORD, CONNECTION 1-757-562-21 CORD, POWER 4-664-750-11 SPECIFICATIONS SHEET, 2420 U 4-664-754-11 QUICK START, 2420 U

Weight saver (1)

Battery pack (1)

Supplied with 303 B22

319 306

BB8 307

314 308
4-665-934-01 TAPE LCD2 4-665-931-01 SPACER LCD 4-641-726-11 SCREW (M2), SPECIAL HEAD 7-628-254-00 SCREW +PS 2.6X5 4-658-316-01 ACE (M2), +B LOCK

B8 B20 B22

AC adaptor (1)

Video cable (1)

Set the DIP switch on the MBX-61 board (Main board) to match with the LCD (A-8023-466-A) that is used in this computer.

330 B8 BBB8

The upper position where ON indication is shown is the ON position. The lower position is the OFF position.

No. ON/OFF

1: OFF

0 : ON

Supplied with 312
3-7 3-8 PCG-FXA53/FXA59 (AM)

3-3-A.

LCD Section (FXA59 Model) Made by SH

424 BB435 403

Ref.No. 414 419
Part No. 1-476-316-11 X-4623-380-1 X-4623-448-2 4-637-902-31 A-8023-483-A 4-637-903-01 X-4624-622-1 4-642-762-31 4-664-249-11 1-757-604-11 4-642-755-01 4-642-756-01 4-642-757-01 4-642-758-01 4-646-217-11 4-635-277-22 4-643-549-12 X-4623-381-1 4-643-366-11 4-643-837-01 4-635-276-22 4-642-760-12 1-961-017-31 4-650-831-01 4-645-219-01
Description INVERTER UNIT HINGE LEFT 15 ASSY HOU, BEZEL 15SA-Z LATCH ASSY LCD SXGA+ 15SH (S) SPRING LATCH ASSY HOU, DISPLAY 15SA-Z COVER HINGE (15) LABEL ID (U) PWB, FLEXIBLE PRINT (SINGLE) BRACKET LCD BRACKET LCD BRACKET LCD BRACKET LCD COVER SCREW (DL) (BL) (DR) (BR) SIDE (15)

Ref.No. B8 B22 B23 B30

Part No. 4-641-726-11 4-642-761-01 4-644-165-01 4-643-550-01
Description SCREW (M2), SPECIAL HEAD +P M2X3 LOCK SCREW (M2.6X4), 0 PLATE P1 MAIN +P 2.6X6 LOCK PRECISION TYPE3

406 B434 408

Supplied with 403 423
COVER SCREW LOWER COVER SCREW SHAFT HINGE RIGHT 15 EDGE GUARD HINGE (15) SHIELD (LCD) COVER SCREW UPPER CUSHION CENTER HARNESS,LCD (SXGA+) SHIELD TAPE (SK) LCD TAPE 13.3

407 B431

438 B431
Set the DIP switch on the MBX-61 board (Main board) to match with the LCD (A-8023-483-A) that is used in this computer.

437 422

401 B414 Supplied with 428

ON/OFF 1 1

No. 0 : ON 1: OFF
3-8(a) 3-8(b) PCG-FXA53/FXA59 (AM)
3-4. Connector Section (CH Type only)

Ref.No. 901

Part No.

Description

1-779-745-21 [CH].JACK, DC

DC IN connector

Bracket I/O 902 901
9-885-018-97 [CH].CONNECTOR (1.2MM), USB

USB connector

9-885-018-98 [CH].CONNECTOR (1.6MM), USB
Among the parts that are used on the boards of this model, only the connectors that are show in the list can be replaced. (The parts other that the specified connectors cannot be replaced.)
Before replacing the connector of reference number 901, 902 and 903, remove the bracket I/O.

901 902

3-10 (END) PCG-FXA53/FXA59 (AM)
CHAPTER 4. OTHERS 4-1. Replacing the CPU

1. Removing the CPU

J-2507-309-1 JIG FOR COU Fig. Part No. Description
Install the special tool in the CPU. 2 Insert a flat head (-) screwdriver tip into the groove as shown. 3 While holding the special tool, slant the screwdriver in the direction of the arrow. 4 The base under the CPU moves slightly in the direction of the arrow and the CPU lock is released. 5 Remove the special tool. 6 The CPU can be removed upward.

2. Installing the CPU

NOTE : Attach the CPU while aligning the cut-out with this position. 1 3
1 Insert all pins of the replacement CPU into the holes of the base and push the CPU in the direction of the arrow. 2 Install the special tool in the CPU.
3 Insert a flat head (-) screwdriver tip into the groove as shown. While holding the special tool, slant the screwdriver it in the direction of the arrow. 4 The base under the CPU moves slightly in the direction of the arrow and the CPU is locked. 5 Remove the special tool.

NOTE : Do not use screwdrivers having a large tip than the width of the groove. Otherwise, it may cause the groove to be damaged. When installing the special tool in the CPU, align the convex of the base.
4-1 (END) PCG-FXA53/FXA59 (AM)
List of PCG-FX Series (As of July, 2002)

Model Name

PCG-FX190 PCG-FX170 PCG-FX150 PCG-FX140 PCG-FX120 PCG-FX190K PCG-FX170K PCG-FX150K PCG-FX140K PCG-FX120K PCG-FX290K PCG-FX290 PCG-FX270K PCG-FX270 PCG-FX250K PCG-FX250 PCG-FX240K PCG-FX240 PCG-FX220K PCG-FX220 PCG-FX210 PCG-FX215 PCG-FX390 PCG-FX370 PCG-FX340 PCG-FXA36 PCG-FXA33 PCG-FXA32 PCG-FX410 PCG-FXA49 PCG-FXA47 PCG-FXA678 PCG-FXA53 PCG-FXA59 9-874-505-01 9-874-507-01 9-874-509-01 9-874-549-02 : Additional Models
This manual and the constituent data may not be replicated, copied nor reprinted in whole or in part without prior written authorization of Sony Corporation.

Service Manual Part No.

9-872-179-11

9-872-194-11

9-874-409-11

9-874-427-11

9-874-404-11 9-874-432-11 9-874-495-01

9-874-453-01

Sony Corporation
English 2002D1600-Sony Corporation Published by Sony EMCS VAIO-GSC [SNT]

Suffix

-01 -02

Ver. 1 Ver. 2

2002.04.26 2002.07.01 First Edition

Contents

QM No.
Front Page (Model Line Up), Page 3-8(a), Page 3-8(b), Back Cover

N2002_064K

< Remarks >
[Confidential] PCG-FXA53/FXA59 (AM)