3-264-085-11(1)

Step 2: Checking if the Code Number Works 1 Turn on the component you want to set up. 2 Aim the Remote Commander at the component and press a
button to check if that button works. For example, press the 1 button to see if it works on your component.
Remote Commander Operating Instructions Mode demploi (au verso)

2004 Sony Corporation

RM-V202T
Changing the Component Type on the VCR, SAT and DVD buttons
At the factory, VCR is assigned to the VCR button, satellite tuner is assigned to the SAT button and DVD player to the DVD button. By completing the following procedure, you can change this setting so that you can assign any component to these buttons.
Even if you try to program more than four operations and press the corresponding buttons in step 2 above, only the first four buttons that were pressed will be programmed. If you try to program only one operation on a macro key, the setting operation will be rejected. You can program the Channel Macro function for up to three components only. To program a fourth component, first clear all macro keys for a component. If you have programmed the Channel Macro function for TV or satellite tuner operation, the button used as a macro key cannot be used for Fastext buttons.
Remote Button Descriptions

General

TV VCR SAT DVD
Operating a satellite tuner
2 To change the programme. 3 To select double-digit numbers. Work in the same way as your satellite tuners commander. 4 To change the input mode (H/V). 8 To move the cursor upward, downward, to the right or left. 9 To call up the MENU display. qd To select a number between 20 and 29. qf PROGR+: Programme up. PROGR: Programme down. qh To operate JUMP, FLASHBACK or CHANNEL RETURN function on the satellite tuner, depending on the manufacturers setting. qj To bring up the Master Guide. qk To enter the selection. ql Fastext buttons.

Specifications

Operable distance Power requirements Battery life Dimensions Mass Approx. 7 m (23 ft) (varies depending of the component of each manufacturer) Two size AA (R6) batteries (not supplied) Approx. 6 months (varies depending on frequency of use) Approx. 32 mm (w/h/d) (2 1/7/5/16 in.) Approx. 95 g (3.4 oz.) (not including batteries)
Component code numbers / Codes des appareils
English TV/VCR/COMBO* The left row of the table shows the brand, the center row shows the component (TV, VCR or COMBO) and the right row shows the code No.
* COMBO stands for the unit combined with TV and VCR.

TV/VCR/COMBO

Brand Sony Component TV VCR (VTR1:Betamax) VCR (VTR2:8mm) VCR (VTR3:VHS) VCR (VTR4:DV) VCR (VTR5:DV) VCR (VTR6:DV) Aiwa TV VCR Akai TV VCR Alba TV VCR Amstrad VCR Audio Sonic TV Baird VCR B&O TV (Bang&Olufsen) VCR Beko TV Bestar TV Blaupunkt TV VCR Blue sky TV Brandt TV Brionvega TV Bush TV VCR CGM TV VCR COMBO Clatronic TV VCR Continental TV Crown TV Daewoo TV VCR COMBO Deccacolour TV Dual TV Emerson TV Fenner TV Ferguson TV VCR COMBO Finlux TV First line TV Fisher TV VCR Fraba TV Funai TV VCR GoldStar/LG TV VCR COMBO Goodmans TV VCR COMBO TV VCR COMBO TV TV VCR TV TV TV TV TV TV VCR Code No. 045 TV 029&VCR TV 074&VCR 024 TV 074&VCR 046 TV 054&VCR TV 074&VCR TV 009&VCR 006 007
3 Check that the other buttons of the Commander are operating
the corresponding functions of the component. You can write down the code number on the label inside the battery compartment lid.

Printed in China

English
While pressing the S (SET) button, press the 1 button. Press the VCR, SAT or DVD button. Press and release the x (stop) button. Press and release one of the following buttons: 1 to assign a VCR 3 to assign a satellite tuner 8 to assign a TV - to assign a DVD
To change or clear a program
When you want to change the setting, or if you are no longer using a programmed operation, follow the procedure below to overwrite or clear the program. 1 Hold down the macro key that you want to change or clear. 2 After waiting for about three seconds, press the new sequence of buttons, or, to clear the program, press and release -, and then press and release ENT. 3 Release the macro key.

MENU GUIDE OK

Setting Up the Remote Commander
About Presetting the Commander
The Commander is preset at the factory to operate Sony brand components. If you are using the Commander with a Sony component, you will not need to preset the Commander before you start using it. To set up the Commander to use with other (non-Sony) manufacturers components, or to use with a component that is not preset at the factory, you will need to follow the instructions in this manual to preset the Commander with the correct code number for your component(s). (See the supplied Component Code Numbers table also.)

Component that can be preset Button Factory setting

Notes on Batteries

Do not mix old batteries with new ones or mix different types of batteries together. If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent the electrolyte from leaking, remove the batteries when you plan not to use the Commander for a long period of time.
If the Commander Does not Seem to be Working.
First, try repeating these setup procedures using the other codes listed for your component (see the supplied Component Code Numbers table). If after trying all the codes listed for your component you still cannot get the Commander to work properly, try the search method described in Searching for the Correct Code.
5 Press and release the t button. 6 Enter the components code number by following steps 2 to 6
of Entering the Code Number, or steps 1to 6 of Searching for the Correct Code.
1 To set up the Commander, press S (SET) while pressing 1. 5 2+: Volume up. 2: Volume down. 7 To mute the volume on the TV. qa To turn on and off the power of the selected component. qs Component select buttons. To switch to the operations of each component, press the button on which that component is assigned.
Design and specifications are subject to change without notice. The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area).
SAT (Satellite tuner) The left row of the table shows the brand and the right row shows the code No. digital: digital satellite tuner analog: analog satellite tuner DVD The left row of the table shows the brand and the right row shows the code No. Franais TV/VCR/COMBO* La colonne gauche du tableau indique la marque, la colonne du milieu indique lappareil (tlviseur (TV), magntoscope (VCR) ou COMBO) et la colonne droite le n de code.
* COMBO dsigne un combin tlviseur-magntoscope.

Operating a DVD

2 Number buttons: To set items selected from the screen. 3 To select numbers 10 and above. 4 To change the sound. 6 To show the current play status on the screen. 8 To move the cursor upward, downward, to the left, or to the right. 9 To display the DVD menu. 0 To record, press N while pressing zREC. First release N, then release zREC. qd To enter the setting. To set items selected from the screen. qf PROGR+: To proceed to the next location or song. Programme up. PROGR: To proceed to the previous location or song. Programme down. qg To switch the subtitle. qh To display the title menu. qj To clear the selected characters from the screen. To select the deck. qk To execute items selected from the screen. ql N: To play. m: To rewind. M: To fast-forward. x: To stop. w; X: To pause.

Setting the Code

Follow steps 1 and 2 below for each component you plan to use with the Commander.
Searching for the Correct Code
If you have tried all the code numbers listed for your component and you still cannot get the Commander to work (or if your component is not listed in the Component Code Numbers table), try these steps.

Operating a Component

1 Press the button of the desired
component on the Commander.
Be sure to wait for about three seconds in step 2 above. While you are holding down the macro key and waiting, the programmed signals are transmitted; therefore, if you are aiming the Commander at your component, the programmed operations may be performed before you go on with the procedure. z The number 5 button and the PROGR+ button each have a tactile dot for ease of use.
Step 1: Entering the Code Number 1 See the supplied Component Code numbers table, and find
the three-digit code number for the desired component. If more than one code number is listed, use the number that is listed first to complete the steps below. For example, if you are setting up a Philips TV, you would use the code number 086. If your component is not listed, see Searching for the Correct Code.
Before starting the Search function
Set each component to the following status to enable the Search function. TV: power-on Other components: power-off
2 Point the Commander directly at the component. 3 Press the button for the function you want to use.
See Remote Button Descriptions for complete descriptions of the buttons on the Commander.
TV VCR/Satellite tuner/DVD/TV

VCR SAT DVD

Sony TV Sony VHS VCR (VTR3) Sony satellite tuner Sony DVD player

Operating a TV

2 To change the programme. Also to turn on the power. 3 To select double-digit numbers. Works in the same way as your TVs commander. 4 To change the input mode. 6 To switch to Teletext. 8 To move the cursor upward, downward, to the right or left. 9 To call up the MENU display. qd To select a number between 20 and 29. qf PROGR+: Programme up. PROGR: Programme down. qg To turn on. To return from Teletext to TV. qh To operate JUMP, FLASHBACK, or CHANNEL on the TV, depending on the manufacturers setting. qk To enter the selection. ql Fastext buttons.
SAT (rcepteur satellite) La colonne gauche du tableau indique la marque et la colonne droite le n de code. digital: rcepteur satellite numrique analog: rcepteur satellite analogique DVD La colonne gauche du tableau indique la marque et la colonne droite le n de code. To set a Component Code (see the instruction manual for details) Pour enregistrer un code dappareil (voir le mode demploi pour plus dedtails)

010 119

Troubleshooting
If you have problems setting up or using the Commander: When setting up the Commander, carefully go through the procedures described in Setting the Code. If the code that is listed first for your component does not work, try other codes for that component in the order in which they are listed. If all the codes fail to work (or if your component is not listed in this manual), try using the procedures in Searching for the Correct Code. Check that you are aiming the Commander directly at the component, and that there are no obstructions between the Commander and the component. Make sure the batteries you are using are not worn out, and that they are inserted correctly. Check that the button of the TV, VCR, SAT, or DVD is pressed to choose your desired component. Check that the component has infrared remote capability. For example, if your component did not come with a remote commander, it is probably not capable of being controlled by a remote commander. Should any problem persist, reset the Commander to the factory setting by pressing the 1, t and 2 buttons simultaneously. Customer Service
If you have any questions or problems concerning the Remote Commander that are not covered in this manual, please call the customer remote helpline. The number is mentioned in the warranty card.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the Commanders supplied with your components. Using this Commander will not increase the functions of your components. The functions of the Commander are limited to the functions of the components themselves. For example, if your TV does not have a MUTING function, the % button on this Commander will not function with your TV. Some functions of the component may not work with this Commander.
The Commander can be set up to operate only one component per button unless their code numbers happen to be the same. For example, you cannot set up the Commander to operate a Sony TV and a Panasonic TV simultaneously (because they use different code numbers). You may not be able to operate even a Sony brand component with the factory presetting. In such a case, follow the procedure in Setting the Code.
1 While pressing the S (SET) button, press the 1 button. 2 On the Commander, press the button of the component that

you want to set up.

123 124
2 While pressing the S (SET)
button, press the 1 button.
3 Press and release the PROGR+ button. Then press and release

the 1 button.

3 Press the button of the
component that you want to set up.
4 Repeat step 3 until the correct code number is found.
Each time you press the PROGR+ button and then the 1 button, a new code number will be transmitted. Keep trying until your component operates as follows: TV: power-off Other components: power-on TV without a power switch: the Channel + function works. Be patient as you do this; it could take as many as 120 tries before the correct code number is located.
While pressing the S (SET) button, press the 1 button. Tout en maintenant la touche S (SET) enfonce, appuyez sur la touche 1.
On the VCR, SAT and DVD buttons, VCR, satellite tuner, and DVD player are assigned respectively at the factory. But you can also assign other components on these buttons. For details, see Changing the Component Type on the VCR, SAT and DVD buttons.

Installing the Batteries

Before replacing the batteries, have new ones ready beforehand. Slide open the battery compartment and insert two size AA (R6) batteries (not supplied). Be sure to line up the + and on the batteries with the + and on the battery compartment.
Setting a channel with a single button (Channel macro function)
You can program the Channel Macro function on any of the buttons listed below (macro keys). For example, instead of pressing 1, 2, and then ENT button to change the TV channel, you can perform these operations by pressing only the N button. The macro keys are: N, m, M, x, X, and zREC. (During TV or satellite tuner operations only.) The series of operations that can be programmed must consist of two to four sequential pressings of the - to 9 buttons or ENT button.

Operating a VCR

2 To change the programme. 3 To select double-digit numbers. Works in the same way as your VCRs commander. 4 To switch the signals supplied to the TV. 6 To expose the on-screen display. 8 To move the cursor upward, downward, to the left, or to the right. 9 To call up the MENU display. 0, ql and w; N: To play. x: To stop. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing zREC. X: To pause. qd To select a number between 20 and 29. qf PROGR+: Programme up. PROGR: Programme down. qg To change the input mode. qk To enter the selection.
4 Enter the components code number.
For example, if you are entering the code for a Philips TV, you would press -86.

5 When the correct code is found, press the t button to store
the code number in the Commanders memory.

Your Code Number

6 Check that the Commander is operating the other functions of
your component by pressing the corresponding buttons on the Commander. If they seem to be working properly, you are done setting up the Commander. If the component does not operate properly, repeat steps 1 to 5 and search for another code. If you still cannot get the Commander to work properly, see Troubleshooting.

013 116

5 Press and release the t button to store

Code No.

015 075
6 Go to Step 2: Checking if the Code Number Works to finish

setting up.

Grundig

022 104

If you press a wrong button in step 4 When to replace the batteries
Under normal conditions, batteries will last up to 6 months. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones. Press the 1 button while pressing the S (SET) button and then go back to step 2.
The Channel Macro function may not work correctly for some components.

Helpline available

Be sure to proceed to each next step in the above procedure within 10 seconds; otherwise setting mode will be canceled.
Hansol Hitachi Hher Hyper ICE Inno-Hit Irradio JVC

011 015

To program a series of operations
1 Press the desired component select button. (You can select TV or satellite tuner only.) 2 While pressing the desired macro key, press the buttons required for the operations in sequence. For example, to program 1 t 2 t ENT on the N button, hold down N first, press 1, 2, and ENT in sequence, and then release N.
Replace both batteries with new ones. Do not take more than 3 minutes to replace the batteries; otherwise, your code number settings will be erased.
Continued on reverse side Suite au verso

Brand Kendo

Kiton Lenco Loewe
Component TV VCR COMBO TV TV TV VCR COMBO TV VCR TV TV

Luxor Mark Matsui

VCR COMBO Medion TV Mitsubishi TV VCR Miver TV NEC TV NEI TV Nokia TV VCR Nokia/ITT TV VCR Nokia Oceanic TV VCR Nordmende TV VCR Okano TV VCR Onwa TV Orion TV VCR COMBO Panasonic TV VCR Philips TV VCR COMBO TV TV VCR TV TV TV TV TV TV VCR TV VCR TV VCR TV VCR COMBO Sanyo Schneider TV VCR TV VCR COMBO TV VCR TV VCR TV VCR TV VCR TV TV COMBO
Phoenix Phonola Pioneer Provision PYE Radio Radiola Roadstar SABA Salora Samsung
SEG Seleco Sharp Siemens Sinudyne Supertech
Code No. 052 TV 054&VCR TV 011&VCR 012, TV 017&VCR 012, TV 018&VCR 046 TV 051&VCR 038, TV 052&VCR TV 051&VCR TV 013&VCR 018, TV 013&VCR 022 TV 060&VCR 022, TV 014&VCR 022, TV 060&VCR 055, TV 060&VCR 020 TV 013&VCR 013 TV 068&VCR 057

LASYSTEMS - Brusselsesteenweg 208 - 1730 Asse - Belgium
Phone: +32-2-4531312 - Fax: +32-2-4531763 E-mail: info@lasystems.be
Sony AFST.BEDIENING RM-V 202T (RMV202T)

Price details:

Price excl. VAT: 15.86 Eco fees: 0.32 VAT 21 %: 3.40
PDF generated on: 6 June, 2011

Product details:

Product code: RMV202T EAN: 4901780861392 Manufacturer: Sony

19.58

* VAT included / Main specifications:
Product is discontinued. You can not order it anymore.

Technical details

Connectivity technology: Wireless AA 55 x 32 x 200 mm 95 g

Energy management

Battery type:

Weight & dimensions

Dimensions W x D x H: Weight:
*PLEASE NOTE: Every effort has been made to ensure the accuracy of all information contained herein. Lasystems makes no warranty expressed or implied with respect to accuracy of the information, including price, editorials or specifications. Lasystems or its suppliers shall not be liable for incidental, consequential or special damages arising from, or as a result of, any electronic transmission or the accuracy of the information contained herin, even if Lasystems has been advised of the possibility of such damages. Product and manufacturer names are used only for the purpose of identification.