2-674-862-11(1)

Remote Commander

RM-V310
4 Enter the components code number. For example, if youre entering the code for a Philips VCR, you would press. 5 Press and release the ENT button to store the code number in the Commanders memory.
1 While pressing the SET button, press the POWER button. 2 Press the VCR, CBL, SAT, AMP, CD, or DVD button. 3 Press and release the x (stop) button. 4 Press and release one of the following buttons; to assign a VCR to assign a DAV (DVD/receiver combo) to assign a digital satellite receiver, a digital cable box or a digital video recorder to assign a receiver to assign a CD player to assign a tape deck to assign an MD deck to assign a TV to assign an analog cable box to assign a DVD 5 Press and release the ENT button. 6 Enter the components code number by following steps 2 to 6 of Entering the Code Number, or steps 1 to 7 of Searching for the Correct Code.
If you are using more than one receiver (or amplifier) and have set it on the VCR, CBL, SAT, CD or DVD button, when selecting these buttons you cannot control the volume of the receiver (or amplifier) of the AMP button. If you change the setting of the AMP button to a component other than a receiver or amplifier, the volume control setting of video components will return to TV even if you have changed the factory preset volume control. In this case, you will not be able to control the volume from audio components other than a receiver or amplifier.
Even if you try to program more than four operations and press the corresponding buttons in step 2 above, only the first four buttons that were pressed will be programmed. If you try to program only one operation on a macro key, the setting operation will be rejected. You can program the Channel Macro function for up to three components only. To program for the fourth component, first clear all macro keys for a component.

Your Code Number

Remote Button Descriptions

General

TV/VIDEO
Operating a DVR (Digital video recorder)
2 To switch the output of the SAT receiver to the TV. (When connecting a TV cable or antenna to the receiver, the output switches between a TV and SAT program.) (*2THUMBS+) To select the desired recorded program. (It is necessary to have recorded the desired program.) 3 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). 8 To turn on the display. (*2THUMBS) To select the desired recorded program. (It is necessary to have recorded the desired program.) 9 To bring up Master Guide. (*2Live TV) To bring up Master Guide. q; To clear the setting. To exit the setting menu. qf (*2LIST) To call up the title of the recorded program. qg CH+: Channel up. (*2PAGE+) Page up. CH: Channel down. (*2PAGE) Page down. qh (*2REPLAY) To replay. Or to go into REC/REVIEW mode during play. (After about 5-second rewind, replay begins.) qk To call up the MENU display. (*2EPG) To access to all aspects of the service. ql To move the cursor upward, downward, to the left, or to the right. ql OK: To bring up the Station Index when a program guide is not displayed. To select the channel that is highlighted. wa N: To play. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing zREC. First release N, then release zREC. To stop recording, perform the same procedure. x: To stop. X: To pause.
Operating a digital satellite receiver
2 To switch the output of the digital satellite receiver to the TV. (When you connect a TV cable or antenna to the receiver, the output switches between a TV and SAT program.) 3, 4 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). 5 To use the FAVORITE function. 9 To bring up the Master Guide. q; To exit the mode. qg Channel up: + Channel down: To page through the guide when a program guide is displayed. qh To tune to the last tuned station. qj To bring up the Station Index. qk To call up the MENU display. ql To scroll through the Master Guide. ql OK: To select the channel that's highlighted. To bring up the Station Index when a program guide is not displayed.

Operating a CD player

3 To select the track number. 0 selects track 10. To select track numbers above 10, see the descriptions on the (DOT) button above. 4 To select numbers 10 and above. For example, to select track 15, press (DOT) and then press 5. 8 To switch the display of the CD player to on/off. qd To enter the setting. qg CH+: To select the next track. CH: To select the previous track. qh To select next disc. qj To clear the setting. wa N: To play. m: To rewind. M: To fast-forward. x: To stop. X: To pause.

TV CBL

VIDEO1

DVD CD

SAT AMP
Operating Instructions Manual de instrucciones (parte posterior)

2006 Sony Corporation

Printed in China

VIDEO2

6 Go to Step 2: Checking if the Code Number Works to finish setting up.
To change or clear the program
When you want to change the setting or if you are no longer using that programmed operation, follow the procedure below to overwrite or clear the program.
DIGITAL /ANALOG TWIN VIEW
Step 2: Checking if the Code Number Works
1 Power on the component you want to set up.
To reset to factory preset volume control
In step 3 above, press VOL instead.

English

For the customers in the U.S.A. WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Installing the Batteries

Before replacing the batteries, have new ones ready beforehand. Slide open the battery compartment and insert two size AA (R6) batteries (not supplied). Be sure to line up the + and on the batteries with the + and on the battery compartment.

2 Aim the Remote Commander at the component and press a button to check if that button works. For example, press the POWER button to see if it works on your component. 3 Check that the other buttons of the Commander is operating the corresponding functions of the component. You can write down the code number on the label inside the battery compartment lid.

MUTING

RECALL
1 Hold down the macro key that you want to change or clear.

Operating a Component

1 Press the button of the desired component on the Commander. 2 Point the Commander directly at the component. 3 Press the button for the function you want to use. See Remote Button Descriptions for complete descriptions of the buttons on the Commander.
TV CBL VCR DVD CD SAT AMP
2 After waiting for about three seconds, press the new sequence of buttons, or, to clear the program, press and release , and then press and release ENT. 3 Release the macro key.

EXIT TOOLS

1 To set up the Commander, press SET while pressing POWER. 6 *1Volume up: + Volume down: 7 *1To mute the volume on TV or receiver (amplifier). qa To turn on and off the power of the selected component. qs Component select buttons. To switch to the operations of each component, press the button on which that component is assigned. *1These buttons control the volume of either TV or receiver (amplifier). See Controlling the Volume of Video Components Connected to an Audio System for details.

Operating an MD deck

3 To select the track number. 0 selects track 10. To select track numbers above 10, see the descriptions on the (DOT) button above. 4 To select numbers 10 and above. For example, to select track 15, press (DOT) and then press 5. 8 To change the display mode or turn the display on/off. qd To enter the setting. qg CH+: To select the next track. CH: To select the previous track. qh To select next disc. qj To clear the setting. wa N: To play. m: To rewind. M: To fast-forward. x: To stop. X: To pause. zREC: To record, press N while pressing zREC./ First release N, then release zREC.

Operating a DVD

2 To change the sound. 3 Number buttons : To set items selected from the screen. 4 To select numbers 10 and above. For example, to select track 15, press PIP and then press 5. 8 To show the current play status on the screen. 9 To clear the selected characters from the screen. qd To enter the setting. To set items selected from the screen. qg CH+: To proceed to the next location or song. Channel up. CH: To proceed to the previous location or song. Channel down. qh qj qk ql To display the title menu. To switch the subtitle. To display the DVD menu. To move the cursor upward, downward, to the left, or to the right. ql OK: To execute items selected from the screen. wa N: To play. m: To rewind. M: To fast-forward. x: To stop. X: To pause. zREC: To record, press N while pressing zREC. First release N, then release zREC.

Be sure to wait for about three seconds in step 2 above. While you are holding down the macro key and waiting, the programmed signals are transmitted; therefore, if you are aiming the Commander at your component, the programmed operations may be performed before you go on with the procedure.
If the Commander Doesnt Seem to Be Working.
First, try repeating these setup procedures using the other codes listed for your component (see the supplied Component code numbers). If after trying all the codes listed for your component you still cannot get the Commander to work properly, try the search method described in Searching for the Correct Code.
Controlling the Volume of Video Components Connected to an Audio System
The Commander is factory preset based on the assumption that you hear the sound of your video components from your TVs speakers, and that you hear the sound of your audio components from the loudspeakers connected to your receiver (or amplifier).

Operating a TV

2 To change the input mode. 3, 4 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). 8 To display the current channel on TV. qf To operate the Picture-inPicture function. Press each button or combination of buttons as described in the table below. qg CH+: Channel up. CH: Channel down. qh To operate JUMP, FLASHBACK or CHANNEL RETURN function on the TV depending on the setting of the TV's manufacturer. qj To operate SLEEP function on the TV. (Works only for a TV with the SLEEP function.) qk To call up the MENU display. ql To move the cursor upward, downward, to the left, or to the right, or to enter the selection.
Notes on Using the Remote Commander
Basically, use this Commander in the same way as the Commanders supplied with your components. Using this Commander will not increase the functions of your components. The functions of the Commander are limited to the functions of the components themselves. For example, if your TV does not have a MUTING function, the MUTING button on this Commander will not function with your TV. Some functions of the component may not work with this Commander. If your cable box can control volume, be sure to set its volume switch to a medium position. If the volume on the cable box is turned down completely, you will not be able to adjust your TVs volume with the Commander.

Troubleshooting

If you have problems setting up or using the Commander: When setting up the Commander, carefully go through the procedures described in Setting the Code. If the code thats listed first for your component doesnt work, try all the codes for your component - in the order in which theyre listed. If all the codes fail to work (or if your component is not listed in this manual), try using the procedures in Searching for the Correct Code. Check that youre aiming the Commander directly at the component, and that there are no obstructions between the Commander and the component. Make sure the batteries youre using are not worn out, and that theyre inserted correctly. Check that the button of the TV, VCR, CBL, SAT, AMP, CD or DVD is pressed to choose your desired component. Check that the component has infrared remote capability. For example, if your component didnt come with a remote commander, it probably isnt capable of being controlled by a remote commander. If your video components are connected to an audio system, make sure youve set up the Commander as described in Controlling the Volume of Video Components Connected to an Audio System. Should any problem persist, reset the Commander to the factory setting by pressing the POWER, TV/VIDEO and VOL buttons simultaneously.

Operating a tape deck

4, and wa Tape operation buttons. For dual cassette decks, operation buttons for Deck A (for Sony-brand dual cassette deck, buttons for Deck B). (DOT): To reverse. N: To play. m: To rewind. M: To fast-forward. zREC: To record, press N while pressing zREC. First release N, then release zREC. x: To stop. X: To pause 0, qd, ql and w; Operation buttons for Deck B (for Sony-brand dual cassette deck, buttons for Deck A). ENT: To reverse. : To play. : To rewind. : To fast-forward. : To stop. EXIT: To record, press while pressing MENU. First release , and then release MENU. TOOLS: To pause. qh To select Deck A or Deck B (dual cassette deck only).
If your tape decks commander has one set of tape operating buttons, and has an A/B button for the deck selection, use the RECALL button to select Deck A or Deck B.
When to replace the batteries
Under normal conditions, batteries will last up to six months. If the Commander does not operate properly, the batteries might be worn out. Replace the batteries with new ones.
Searching for the Correct Code
If youve tried all the code numbers listed for your component and you still cannot get the Commander to work (or if your component is not listed in the Component code numbers tables), try these steps. 1 Power on the component you want to set up. Insert a tape or disc if necessary. 2 While pressing the SET button, press the POWER button. 3 Press the button of the component on the Commander that you want to set up. 4 Press and release the CH+ button. Then press and release the POWER button. 5 Repeat step 4 until the correct code number is found. Each time you press the CH+ button and then the POWER button, a new code number will be transmitted. Keep trying until your component operates by receiving the transmitted signal from the Commander (e.g., the power turns off, the CH+ function works, playback starts, etc.). Be patient as you do this; it may take about 100 tries until the correct code number is located. 6 When the correct code is found, press the ENT button to store the code number in the Commanders memory. 7 Check that the Commander is operating the other functions of your component by pressing the corresponding buttons on the Commander. If they seem to be working properly, youre done setting up the Commander. If the component does not operate properly, repeat steps 1 to 6 and search for another code. If you still cannot get the Commander to work properly, see Troubleshooting.

Factory Setting:

Button TV VCR*, CBL*, SAT*, DVD* AMP CD* Controls the volume of TV TV Receiver (or amplifier) Receiver (or amplifier) on the AMP button
*2 This key corresponds to Tivo service or the replay service. Refer to its
instruction manual for details.
Replace both batteries with new ones. Do not take more than 20 minutes to replace the batteries; otherwise, your setting of the code numbers will be erased.
Operating an analog cable box
3 and qd To change the channel. For example, to change to channel 5, press 0 and 5 (or press 5 and ENT). qg CH+: Channel up. CH: Channel down. Notes
There may be cases you may turn on/off the cable box by pressing the CH+ or CH buttons on the Commander. If your cable box can control volume, be sure to set its volume control to a medium position. If the volume on the cable box is turned down completely, you will not be able to adjust your TVs volume with the Commander.
Setting Up the Remote Commander
About Presetting the Commander
The Commander is preset at the factory to operate Sony brand components. If youre using the Commander with a Sony component, you wont need to preset the Commander before you start using it. To set up the Commander to use with other (non-Sony) manufacturers components, or to use with a component that is not preset at the factory, youll need to follow the instructions in this manual to preset the Commander with the correct code number for your components. (See the supplied Component code numbers also.)
Component that can be preset TV Video cassette recorder/Analog cable box/Digital cable box/Digital satellite receiver/Receiver/CD player/Tape deck/MD deck/DVD/ TV/VCR/Digital video recorder/ DAV (DVD/Receiver combo) Button TV VCR CBL AMP CD SAT DVD Factory setting Sony TV Sony VHS VCR analog cable box Sony receiver Sony CD player Sony digital satellite receiver Sony DVD player

Notes on Batteries

Do not mix old batteries with new ones or mix different types of batteries together. If the electrolyte inside the battery should leak, wipe the contaminated area of the battery compartment with a cloth and replace the old batteries with new ones. To prevent the electrolyte from leaking, remove the batteries when you plan not to use the Commander for a long period of time.
* If you assign an audio component on the VCR, CBL, SAT, CD or DVD button, you can control the volume of the receiver (or amplifier) on the AMP button. If you assign video components on these buttons, you can control the volume of the TV.

Setting a channel with a single button (Channel Macro function)
You can program the Channel Macro function on any of the buttons listed below (macro keys). For example, instead of pressing , , and then the ENT button to change the TV channel, you can perform these operations by pressing only the N button. The macro keys are: N, m, M, x, X, and zREC. (During TV, analog cable box, digital cable box, digital satellite receiver or digital video recorder operations only.) The series of operations that can be programmed must be consisted to buttons or ENT of two to four sequential pressings of button.
When setting the component code of a TV to 088 or 089 (codes for a Sony TV) 5 To switch between digital
broadcast and analog broadcast.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use with the Commander.
Step 1: Entering the Code Number
1 See the supplied Component code numbers, and find the threedigit code number for the desired component. If more than one code number is listed, use the number thats listed first to complete the steps below. For example, if youre setting up a Philips VCR, you would use the code number 035. If your component isnt listed, see Searching for the Correct Code. 2 While pressing the SET button, press the POWER button. 3 Press the button of the component that you want to set up.

SET POWER

Thus you can control the volume of your TV or receiver (or amplifier) while operating a video or audio component without first having to press the TV or AMP button. For example, to control the volume for your VCR channels, you dont need to press the TV button first. However, if your video components are connected to an audio system, you probably hear your TVs or VCRs sound from the loudspeakers connected to your receiver (or amplifier), not from your TV speakers. In this case, you need to change the factory setting so that you can control the volume of your video components without first having to switch to the receiver (or amplifier). To change the factory setting for the volume control, follow the procedures below.
q; EXIT qf TWIN VIEW w; OPTION
For the customers in the U.S.A.

Customer Support Information
If after youve read through this manual you still cannot get the Remote Commander to work properly, call the Sony Customer Support Helpline at 1-800-822-2217.

PIP operations

Press TWIN VIEW GUIDE m or M zREC x N X
wa To select TV input source. m: VIDEO 1 N: VIDEO 2 M: VIDEO 3 zREC: VIDEO 4 x: VIDEO 5 X: VIDEO 6
qh To operate JUMP, FLASHBACK or CHANNEL RETURN function on the TV depending on the setting of the TV's manufacturer.
Operating a receiver/amplifier
2 To switch input source by each pressing. 3 To select the input source: 1 selects VIDEO selects VIDEO selects AUX 4 selects TUNER 5 selects CD 6 selects TAPE 7 selects MD 8 selects TV 9 selects PHONO 0 selects DVD qg Presetting frequency up: +, down: Tuning frequency up: +, down: qh To shift band (FM/AM). wa Work as N, M, m, x, X buttons of the CD player. (When a CD player is set up on the CD button.)
This feature is effective only when a receiver (or amplifier) is set up on the AMP button. You cannot control the volume of a receiver (or amplifier) set up on VCR, CBL, SAT, CD or DVD button while operating a component of another button.
The Channel Macro function may not work correctly for some components.
To Turn on/off the window picture. Turn off the window picture. Change the TV channel in the window picture. Change the input mode of the window picture. Move the location of the window picture. Swap the main picture and the window picture. Freeze the window picture.
Operating a digital cable box
2 To switch the output of the SAT receiver to the TV. (When connecting a TV cable or antenna to the receiver, the output switches between a TV and SAT program.) 3 and qd To change the channel (for example, to change to channel 5, press 0 and 5, or press 5 and ENT). 8 To turn on the display. 9 To call up the title bar and toggle the title bar on/off in CABLE mode. q; To exit the setting menu. qf To use the FAVORITE function. qg CH+: Channel up. CH: Channel down. qh To turn on the display of a shortcut menu. qk To call up the MENU display. ql To move the cursor upward, downward, to the left, or to the right. ql OK: To bring up the Station Index when a program guide is not displayed. To select the channel that is highlighted. 3 wa * N: To play. 3 * m: To rewind. *3M: To fast-forward. *3zREC: To record, press N while pressing zREC. First release N, then release zREC. To stop recording, perform the same procedure. 3 * x: To stop. 3 * X: To pause.

DAV (DVD/Receiver combo)

2 To change the input mode. 3 Number buttons: To set items selected on the screen. 4 To select numbers 10 and above. 8 To show the current play status on the screen. 9 To change the sound. qd To enter the setting. qg CH+: To proceed to the previous location or song. CH: To proceed to the next location or song. qh To display the Top Menu. qj To switch the subtitle. qk To call up the MENU. ql To move the cursor upward, downward, to the left, or to the right. OK: To enter the selection of the MENU display. wa N: To play. m: To rewind. M: To fast-forward. zREC*: To record. x: To stop. X: To pause.

* To avoid accidental recording, the REC key does not work unless pressed for more than 1 second (factory setting).

Specifications

Operable distance Power requirements Battery life Dimensions Mass Approx. 7 m (23 ft) (varies depending of the component of each manufacturer) Two size AA (R6) batteries (not supplied) Approx. 1 year (varies depending on frequency of button use - up to approx. 300 times per day.) Approx. 29 mm (w/h/d) (2 1/3/3/16 in.) Approx. 132 g (4.6 oz.) (not including batteries)
If you have programmed the Channel Macro function for TV operation, the button used as a macro key cannot be used for PIP operation.
To program a series of operations
1 Press the desired component select button. (You can select TV, analog cable box, digital cable box digital satellite receiver or digital video recorder only.) 2 While pressing the desired macro key, press the buttons required for the operations in sequence. For example, to program t t ENT on the N button, hold down N first, press , , and ENT in sequence, and then release N.
Design and specifications are subject to change without notice.
The Commander can be set up to operate only one component per button unless their code numbers happen to be the same. For example, you cannot set up the Commander to operate a Sony TV and a Panasonic TV simultaneously (because they use different code numbers). You may not be able to operate even a Sony brand component with the factory presetting. In such a case, follow the procedure in Setting the Code.

TV CBL VCR

Changing the Component Type on the VCR, CBL, SAT, AMP, CD and DVD buttons
At the factory, video cassette recorder is assigned on the VCR button, digital satellite receiver on the SAT button, analog cable box on the CBL button, receiver on the AMP button, CD player on the CD button and DVD player on the DVD button. By completing the following procedure, you can change this setting so that you can set up any component on these buttons.
Changing the Factory Setting for the Volume Control
1 While pressing the SET button, press the POWER button. 2 Press the AMP button. 3 Press the VOL+ button. 4 Press the ENT button. The volume control setting is changed to receiver/amplifier. You can control the volume of the receiver (or amplifier) of the AMP button while selecting any component.

RM-V310

TV/VCR COMBO

Code No.

001 (VTR1:Betamax) 002 (VTR2:8mm) 003 (VTR3:VHS) 004 (VTR4:DV) 005 (VTR5:DV) 006 (VTR6:DV) 030 041, 050, 035 052, 053, 054 017, 040 033, 046 020, 022, 017, 066 012, 018, 035 007, 041, 012 044, 015, 012, 064 017, 039, 044, 022, 023, 019, 020, 021, 041, 058, 070, 071 033, 037, 038, 032, 007, 012, 051, 042, 043 011, 007, 012, 011 012, 008, 007, 033, 017, 039, 040 017, 047, 048, 049, 039, 040 017, 039, 035, 040 041, 035, 008, 036, 037, 033, 038, 052 013, 011, 012, 010, 063, 073 017, 039, 012, 038 008, 007 026, 027, 028, 029, 056, 057, 065, 059 028, 041, 024 017, 039, 040 012, 055, 072 009, 010, 011, 012, 060, 068 008, 007 011, 012, 044, 020, 064 035, 013, 011, 012, 011, 012, 009, 010, 006 007, 008, 011, 012, 013, 014, 015, 016, 063 012, 033, 031, 038, 027, 041 025, 016, 033, 038, 046, 044, 035, 074, 064 015, 016, 024, 038, 026, 027, 028, 029 030, 041, 013, 011, 012, 041, 067, 063 041, 075, 017, 039, 040 017, 039, 041, 040 012, 011 015, 014, 052, 069 030, 031, 038, 034, 035 033, 017, 039, 040 034
Component code numbers / Codes dappareils / Nmeros de cdigo de componentes

Daewoo Emerson

Code No. TV
027 003, 013, 012, 030, 046, 050, 051, 049 011, 018, 018, 034, 027 034
012, 012, 009, 024, 025, 029 041

2006 Sony Corporation

Printed in China

2-674-863-11(1)

English
TV, VCR, Analog cable box, Digital cable box, SAT (digital satellite receiver), RECEIVER/AMP (receiver or amplifier), CD (CD player), TAPE (tape deck), MD (MD deck), DVR (digital video recorder), DVD and DAV (DVD/Receiver COMBO) The left row of the table shows the brand and the right row shows the code No. TV/VCR COMBO* The left row of the table shows the brand, and the right two rows show the code No. for each section of the TV and VCR.
* COMBO stands for the unit combined with TV and VCR.
Sony Admiral Akai AOC Audinac Bell&Howell Broksonic Craig Croslex Crown Curtis Mathis Daewoo Daytron Durabrand Emerson ESA Fisher General Electric GoldStar/LG Hitachi JC Penny Jensen JVC KTV LXI(Sears) Magnavox Marantz Memorex Mitsubishi/MGA NEC Orion Panasonic Philco Philips Pioneer Portland Proton Quasar Radio Shack RCA/PROSCAN Samsung Sanyo Scott Sharp Signature 2000 Sylvania Symphonic Toshiba Videch Wards Zenith
001, 088, 089 002, 014, 014, 009, 038 003, 012, 072 022, 034, 020, 034 003, 019, 034 035, 036, 003, 041, 077, 078 022, 013, 020, 021, 003, 015, 042, 034, 025 002, 018, 003, 007, 045, 049 003, 013, 012, 030, 046, 050, 051, 049 031, 013, 003, 032 003, 002, 030, 028 033, 013, 003, 034 002, 003, 011, 025, 019, 012, 052 011, 012, 013, 003, 043, 047, 083, 084, 077 024, 003, 012, 066 003, 012 082, 087 018, 016, 007, 049, 067, 074, 076 011, 013, 003, 068, 035, 031 011, 056, 043, 017 037, 018, 019 003, 018, 007, 048 002, 012, 024, 034, 015 002, 003, 004, 005, 006, 007, 008, 044, 045, 046, 053, 086 026, 012, 013, 003, 055, 027 025, 054, 034 034, 012 014, 013, 015, 070 014, 009 011, 012, 003, 073 023, 039, 040, 034 060, 019, 014, 052, 059, 075 031, 003, 012 013, 003, 015, 012 009, 010
Mini Hi-Fi Component System The left row of the table shows the brand, and the right four rows show the code No. for each section of the Mini Hi-Fi Component System.
Admiral Aiwa Akai Audio Dynamic Bell&Howell Broksonic Canon Citizen Craig Curtis Mathis Daewoo DBX Dimensia Emerson Fisher Funai General Electric GoldStar/LG GO VIDEO Hitachi HQ Instant Replay JC Penny JVC Kenwood LXI(Sears) Magnavox Marantz Marta Memorex Minolta Mitsubishi/MGA Multitech NEC Olympic Optimus Orion Panasonic Pentax Philco Philips Pioneer Quasar RCA/PROSCAN Realistic Samsung Sansui Sanyo Scott Sharp Shintom Signature 2000 Singer Sylvania Symphonic Tashiro Tatung Teac Technics Toshiba Wards Yamaha Zenith
General Electric GoldStar/LG Magnavox Panasonic Quasar RCA/PROSCAN Samsung Symphonic

Analog cable box

Hamlin/Regal Jerrold/G.I. Oak Panasonic Pioneer Scientific Atlanta Tocom Zenith

Franais

TV (tlviseur), VCR (magntoscope), dcodeur analogique, dcodeur numrique, SAT (rcepteur satellite numrique), RECEIVER/AMP (ampli-tuner ou amplificateur), CD (lecteur CD), TAPE (platine cassette), MD (platine MD), DVR (magntoscope numrique), DVD et DAV (combin DVD/ampli-tuner) La colonne gauche du tableau indique la marque et la colonne droite le numro de code. TV/VCR COMBO* La colonne de gauche du tableau indique la marque et les deux colonnes de droite indiquent le numro de code pour chaque section du tlviseur (TV) et du magntoscope (VCR).
* COMBO dsigne un combin tlviseur-magntoscope.
022, 023, 024, 025, 026 031, 001, 002, 003, 004, 005, 006, 007, 008, 018, 022, 032 027, 028, 029 019, 020, 021 014, 015 009, 010, 011 031, 016, 017 012, 013