SDM-M51D

SERVICE MANUAL
US Model Canadian Model AEP Model

SPECIFICATIONS

LCD panel Input signal format Panel type: a-Si TFT Active Matrix Picture size: 15.1 inch RGB operating frequency* Horizontal: 28-64 kHz Vertical: 48-75 Hz Horizontal: Max. 1024 dots Vertical: Max. 768 lines Analog RGB: HD15 Digital/Analog RGB: DVI-I 29 pins Analog RGB video signal: 0.7 Vp-p, 75, positive SYNC signal: TTL level, 2.2k, Positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75, negative (Sync on green) Digital RGB video signal: TMDS (single link) 1W x 2 Stereo minijack Accepts impedance of 16-48 Stereo minijack Accepts impedance of 47 k Accepts level 0.5 Vrms 100-240 V, 50-60 Hz, 0.4 - 0.2A (including AC adapter) Power consumption Max. 22W (including AC adapter) Operating temperature 5-35 Dimensions (width/height/depth) Display (upright): Approx. 387 x 345 x 180 mm (15 x 13 x 7 inches) (with stand) Approx. 387 x 296 x 48 mm (15 x 11 x 115/16 inches) (without stand) Mass Approx. 4.6 kg (10 1b 14 oz) (with stand) Plug & Play DDC2B Power requirements
Resolution Video input connector Input signal levels
Audio output Headphones jack Audio in jack
* Recommended horizontal and vertical timing condition Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 s, whichever is larger. Horizontal blanking width should be more than 2.5 sec. Vertical blanking width should be more than 450sec. Design and specifications are subject to change without notice.
TFT LCD COLOR COMPUTER DISPLAY

Power saving function

This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below. Power mode normal operation active off** (deep sleep)* power off Power consumption* 22 W (max.) 2 W (max.) 2 W (max.)

1 (power) indicator

Automatic picture quality adjustment function
When the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitors memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen for any timing within the monitors frequency range (horizontal: kHz, vertical: Hz). Consequently, the first time the monitor receives input signals that do not match one of the factory preset modes, the monitor may take a longer time than normal for displaying the picture on the screen. This adjustment data is automatically stored in memory so that next time, the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes. In all modes as above, if the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received.
Note While the automatic picture quality adjustment function is activated, only the 1 (power) switch will operate.

green orange*** off

deep sleep is the power saving mode defined by the Environmental Protection Agency. ** When your computer enters the active off mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After 20 seconds, the monitor enters the power saving mode. *** If the horizontal or vertical sync signal is received by the monitor, the power indicator may alternately blink green and orange.

SDM-M51D(E) -2-

SDM-M51D SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are pinched or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below.

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. AVERTISSEMENT!! NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE DEMAGNETISATION EST ENLEVE. ATTENTION AUX COMPOSANTS RELATIFS LA SCURIT!! LES COMPOSANTS IDENTIFIS PAR UNE TRAME ET UNE MARQUE SONT CRITIQUES POUR LA SCURIT. NE LES REMPLACER QUE PAR UNE PICE PORTANT LE NUMRO SPECIFI. LES RGLAGES DE CIRCUIT DONT LIMPORTANCE EST CRITIQUE POUR LA SCURIT DU FONCTIONNEMENT SONT IDENTIFIS DANS LE PRSENT MANUEL. SUIVRE CES PROCDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQUUN MAUVAIS FONCTIONNEMENT EST SUSPECT.

To Exposed Metal Parts on Set

0.15 F

1.5 k

AC Voltmeter (0.75 V)

Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

SDM-M51D(E) -3-

TABLE OF CONTENTS

Section

1. DISASSEMBLY 1-1. Bezel Assy, and Back Cabinet Removal 1-2. TFT Panel and Chassis Removal Inverter Board Removal 1-3. A Board Removal 2. ADJUSTMENTS 2-1. Adjustment (1) 2-2. Adjustment (2) 2-3. Table (1) & (2) 2-4. Timing Specification 3. SCHEMATIC DIAGRAMS 3-1. Note 3-2. Block Diagrams 3-3. (1) Schematic Diagram of A (a-e) Board (2) Schematic Diagram of H Board (3) Schematic Diagram of J Board 4. EXPLODED VIEWS 4-1. LCD Monitor 4-2. Packing Materials 5. ELECTRICAL PARTS LIST

1-1 1-2 1-2 1-3

2-1 2-2 2-3 2-4

3-1 3-2 3-3 3-10 3-11

4-1 4-2 5-1

SDM-M51D(E) -4-

SECTION 1 DISASSEMBLY 1-1 BEZEL ASSY AND BACK CABINET REMOVAL

SDM-M51D(E) 1-1

1-2 -- TFT PANEL AND CHASSIS REMOVAL --- INVERTER BOARD REMOVAL --

SDM-M51D(E) 1-2

1-3 A BOARD REMOVAL

SDM-M51D(E) 1-3

SECTION 2 ADJUSTMENTS
2-1. FUNCTIONAL ALIGNMENT (1) Procedures of how to go to service mode. 1. Hold + and - key power on, SDM-M81 goes into service mode. 2. Press MENU key-----ODS display. 3. Press - key to go to second pages late icon. 4. Press OK key-----service menu display. 5. Select one of features. 6. Press MENU key to exit OSD. 7. Power OFF then ON again, monitor go to normal mode. If you would like to enter service mode again, performing the above procedures cycle.

ANALOG

9300K 6500K 5000K SUB-BRIGHTNESS R G B SUB-CONTRAST
DIGITAL CONFIGURATION (N/A) CHIPS SYNC SLICE (N/A) TMDS EXIT (N/A) (N/A) OK COLOR TEMP INITIAL EE PROM CLEAR ETI TIME PRESET B/C/C EEPROM TEST EXIT PERFORM

(N/A) (N/A)

BRT 1 CON 1 EXIT
INITIAL EE PRM 9300K 6500K 5000K (N/A) BRT 2 CON 2 BLK 2 EXIT

R G B EXIT

Note 1. N/A means Not applied. 2. This service menu only provides both Configuration & Sync slice functions. This other were used for design engineering. There is no guarantee of using those N/A functions.

SDM-M51D(E) 2-1

2-2. FUNCTIONAL ALIGNMENT (2)
This paper documents the functional alignment (Used Color meter) procedure of Sony LCD monitor SDM-M51D. Equipment PC workstation with Windows 95 Installed PS/2 mouse is required Software: KSi Engineering alignment software tool Color meter: Option Signal generator: Option Cable: Special RS232 interface cable Setup 1. Copy ECS software <ALIGN.EXE> into a new PC directory. 2. Prepare timing & pattern data for signal generator according to Sonys timing specifications. 3. Prepare timing files for <ALIGN.EXE>. 4. Connect monitor interface cable between flat panel monitor and PC com port. 5. Connect monitor video cable to signal generator. 6. Put Topcon 50cm from the monitor; Point it perpendicularly at the center of the display; Achieve the best focus through the eyepiece. 7. Enclose the monitor and Topcon in a light-shield chamber. 8. Set up [SERVICE MODE] of the monitor. Download In order to enhance productivity, a software utility is provided to download default data to LCD monitor. The default data includes color balance data and geometry timing data. Computer:

Operation 1. Execute software <ALIGN.EXE>. 2. Click on Setup menu. 3. Select Monitor type as Sony SDM-M51D. 4. Select COM PORT according to hardware connection. 5. Click <OK> to save the new setup configuration. 6. Quit this application and Re-enter to make the new settings effective. On Screen Adjustment 1. Click on the Monitor icon; an virtual monitor panel would show up. 2. On entry, the software tries to establish a communication link with the monitor. The monitor internal DACs are read and shown on screen sliders. A CONNECT icon would show up on the lower left corner of the dialog screen. 3. An error message would pop up should communication fail. A BREAK icon would show up on the dialog screen. If this happens, check the hardware setup, communication cable, and the connection. Warm up time Allow 30 minutes warm up time before doing any adjustment. Color Adjustment 1. 9300K color adjustment --Center adjustment-a. Click Color Temperature as 9300. b. Apply 40% IRE white video field, primary mode. c. Make sure backlight register data is 0 (100%).
d. Click Refresh. Refer to table 1 for default data for color adjustment. e. Adjust sub_brt_B to achieve color temperature. Refer to table 2 for specification. f. Click Save this color for a 9300K color save. 2. 5000K color adjustment a. Click Color Temperature as 5000. b. Repeat alignment procedure as 9300 steps b-f. 3. 6500K color adjustment a. Click Color Temperature as 6500. b. Repeat alignment procedure as 9300 steps b-f. Geometry Adjustment 1. Connect the personal computer which has alignment data. 2. Click Refresh (inside Geometry Register Box). 3. Adjust Pitch for optimum screen performance. 4. Adjust Phase for optimum screen performance. 5. Adjust H position to make the screen center horizontally. 6. Adjust V position to make the screen center vertically. 7. Repeat steps 3-6 for best picture performance. 8. Click Save Geometry to perform a user timing mode save. 9. Repeat step 1-7 for each of the user present timings.

SDM-M51D(E) 2-2

2-3. Table 1 & 2 Table 1: Default data for analog color adjustment Color Brightness (G) Contrast (G) Sub-Brt-R Sub-Brt-B Sub-Brt-G Sub-Cont-R Sub-Cont-B Sub-Cont-G 9300K 6500K 5000K 70 70

Table 2: Specifications for color adjustment Color 5000 Tole x y 358 Y (40% IRE) 35
Y: Luminance measurements are in cd/m

SDM-M51D(E) 2-3

2-4. TIMING SPECIFICATION
PRESET MODE SIGNAL MODE RESOLUTION DOT CLOCK HORIZONTAL H. TOATL H. SYNC H. BP H. ACTIV VERTICAL V. TOTAL V. SYNC V. BP V. ACTIV H/V POLARITY MODE 1 VESA 60Hz 640 X 480 25.175 MHz usec 31.778 3.813 1.907 25.422 msec 16.683 0.064 1.049 15.253 N/N MODE 2 MAC 66Hz 640 X 480 30.240 MHz usec 28.571 2.116 3.175 21.164 msec 15.000 0.086 1.114 13.714 N/N MODE 3 VESA 75Hz 640 X 480 31.500 MHz usec 26.667 2.032 3.810 20.317 msec 13.333 0.080 0.427 12.800 N/N MODE 4 VESA 70Hz 720 X 400 28.350 MHz usec 31.746 3.810 1.905 25.397 msec 14.254 0.095 1.079 12.698 N/P MODE 5 VESA 56Hz 800 X 600 36.000 MHz usec 28.444 0.889 4.667 22.222 msec 17.778 0.057 0.626 17.067 N/N MODE 6 VESA 60Hz 800 X 600 40.000 MHz usec 26.400 3.200 2.200 20.000 msec 16.579 0.106 0.607 15.840 P/P MODE 7 VESA 72Hz 800 X 600 50.000 MHz usec 20.800 2.400 1.280 16.000 msec 13.853 0.125 0.478 12.480 N/N MODE 8 VESA 75Hz 800 X 600 49.500 MHz usec 20.110 1.616 3.232 16.162 msec 13.333 0.064 0.448 12.800 P/P
PRESET MODE SIGNAL MODE RESOLUTION DOT CLOCK HORIZONTAL H. TOATL H. SYNC H. BP H. ACTIV VERTICAL V. TOTAL V. SYNC V. BP V. ACTIV H/V POLARITY
MODE 9 PMAC X 624 57.285 MHz usec 20.110 1.117 3.910 14.524 msec 13.413 0.060 0.744 12.549 N/N
MODE 10 VESA 60Hz 1024 X 768 65.000 MHz usec 20.677 2.092 2.462 15.754 msec 16.666 0.124 0.600 15.880 N/N
MODE 11 VESA 70Hz 1024 X 768 75.000 MHz usec 17.707 1.813 1.920 13.653 msec 14.272 0.106 0.513 13.599 N/N
MODE 12 VESA 75Hz 1024 X 768 78.750 MHz usec 16.660 1.219 2.235 13.003 msec 13.328 0.050 0.466 12.795 P/P
MODE 13 MAC 768 75Hz 1024 X 768 80.000 MHz usec 16.600 1.200 2.200 12.800 msec 13.346 0.050 0.498 12.749 N/N

SDM-M51D(E) 2-4

SECTION 3 SCHEMATIC DIAGRAMS
NOTE: *All capacitors are in uF unless otherwise noted.(pF:uuF) Capacitors without voltage indication are all 50V. *Indication of resistance,which dos not have one for rating electrical power,is as follows. Chip resistor type 0603 1/16W *All resistor are in ohms. *Resistors with # mark are not mounted. *the circuit diagram of the A mount is splitted to 6 sheets.(A-a,A-b,>>A-e) *Circled number snown at edge or each circuit diagrams indicate connections between different sheets. (Example; ab1 indicate connection between same marking points of sheet A-a and A-b)

-- H BOARD (Conductor Side) --

SW803 SW-DPST

KEY UP

1 SW804 SW-DPST 2

KEY DOWN

1 SW805 SW-DPST 4

KEY PLUS

KEY MINUS

SW806 SW-DPST

1 SW807 SW-DPST 2

KEY AUTO

CN801 B11B-PH-K

TO A BOARD CN5 1-12pin

LED801

3 LED AMB LED GRN LED 5V 2 1

DUAL_LED_CA

SDM-M51D(E) 3-10
-- Schematic Diagram of J Board --
-- J BOARD (Conductor Side) --

R702 150

R701 150

C702 10F

OPL+ OPLOPROPR+

CN702 B5BPH-PH-K

C701 10F

PHONEJACK STEREO SW

Input From M/B`s Amp

CN703 S4B-PH-K

SPK SPK SPK SPK L+ LRR+ 2 1

Speakers

SDM-M51D(E) 3-11

4-1 LCD MONITOR

REF NO. 7
PART NO. 1-476-422-11 1-803-808-11 X-4038-946-1 4-079-642-21 A-1272-429-A A-1372-905-A 4-082-985-01
DESCRIPTION INVERTER PANEL, LCD CABINET ASSY, BACK COVER, REAR A MOUNT H MOUNT
REMARK 241-SM15012 245-151LG01 422-S-0305020 422-0145020 209-5020010 209-5010030

REF NO. 12 13

PART NO. A-1388-294-A X-4038-369-1 1-529-902-11 X-4038-370-1 1-518-777-11 1-518-777-21
DESCRIPTION J MOUNT BEZEL ASSY SPEAKER (20x40mm) STAND ASSY LAMP ASSY (UPPER) LAMP ASSY (LOWER)
REMARK 209-5010040 422-S-0105010 KSI40X20 422-S-0205010 N/A N/A

SDM-M51D(E) 4-1

LABEL, INFORMATION 610-0605022

REF NO. 61 62

PART NO. 4-082-376-01 4-079-619-01 4-079-620-01 1-476-397-11 1-823-049-11 1-765-720-21 1-765-719-21 Pending 1-778-967-21 1-785-512-31 4-082-179-11 1-757-372-11 4-080-078-01
DESCRIPTION INDIVIDUAL CARTON CUSHION (LEFT) CUSHION (RIGHT) ADAPTOR, AC CABLE, RGB (HD15-DVI) CORD SET, POWER (U/C) CORD SET, POWER (AEP) DISK, INFORMATION(CD-ROM) ADAPTOR, CONVERSION (U/C) MANUAL, INSTRUCTION CORD, CONNECTION (WITH PLUG) BOARD, SPACER
REMARK 600-9105020 404-9135010 404-9145010 201-6018012 186-8010001 181-IS105011 181-IS205012 617-0105022 204-MAC2101 612-0105022 186-8010002 604-9185010
CONNECTOR, D SUB (15P CHANGER) (AEP) 204-TRYG301
SECTION 5 ELECTRICAL PARTS LIST NOTE:
The components identified ! Marked are critical for safety. Replace only with the part number specified. Les composants identifis par la marque ! sont critiques pour la securit. Ne les remplacer que par une pice portant le numro spcifi. Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. RESISTORS All resistors are in ohms F: nonflammable CAPACITOR MF: uF COIL UH: uH

When indicating parts by reference number, please include the board name.
All variable and adjustable resistors have characteristic curve B, unless otherwise noted.

SDM-M51D(E) 5-1

No. # Board Type ! / * Ref. No. A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C005 CAPACITOR 5 A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C014 CAPACITOR 14 A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C025 CAPACITOR 25 A C026 CAPACITOR 26 A CCAPACITOR A C028 CAPACITOR 28 A C029 CAPACITOR 29
Part No. 1-131-992-11 1-128-126-11 1-164-505-11 1-162-970-21 1-128-126-11 1-128-126-11 1-128-126-11 1-117-370-11 1-117-370-11 1-117-370-11 1-107-820-11 1-107-820-11 1-107-820-11 1-107-820-11 1-128-126-11 1-164-933-11 1-164-933-11 1-164-933-11 1-164-933-11 1-162-970-21 1-162-970-21 1-162-970-21 1-117-370-11 1-162-970-21 1-107-820-11 1-107-820-11 1-107-820-11 1-164-933-11 1-164-933-11
Description CAP- Y5V 0.1UFZ 25V CHIP 0603 CAP-EC 100UF 25V 6.3*7.0 SAX CAP- Y5V 2.2UFZ 16V CHIP 0805 CAP-X7R 0.01UFK 50V CHIP 0603 CAP-EC 100UF 25V 6.3*7.0 SAX CAP-EC 100UF 25V 6.3*7.0 SAX CAP-EC 100UF 25V 6.3*7.0 SAX CAP- Y5V 10UFZ 10V CHIP 1206 CAP- Y5V 10UFZ 10V CHIP 1206 CAP- Y5V 10UFZ 10V CHIP 1206 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-EC 100UF 25V 6.3*7.0 SAX CAP-X7R 220PFJ 50V CHIP 0402 CAP-X7R 220PFJ 50V CHIP 0402 CAP-X7R 220PFJ 50V CHIP 0402 CAP-X7R 220PFJ 50V CHIP 0402 CAP-X7R 0.01UFK 50V CHIP 0603 CAP-X7R 0.01UFK 50V CHIP 0603 CAP-X7R 0.01UFK 50V CHIP 0603 CAP- Y5V 10UFZ 10V CHIP 1206 CAP-X7R 0.01UFK 50V CHIP 0603 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-Y5V 0.1UFZ 16V CHIP 0402 CAP-X7R 220PFJ 50V CHIP 0402 CAP-X7R 220PFJ 50V CHIP 0402
Remarks 122-CY104Z25TV 162-SAX101M25 122-CY225Z16TX 122-CX103K50TV 162-SAX101M25 162-SAX101M25 162-SAX101M25 122-CY106Z10TW 122-CY106Z10TW 122-CY106Z10TW 122-CC104Z16TZ 122-CC104Z16TZ 122-CC104Z16TZ 122-CC104Z16TZ 162-SAX101M25 122-CX221J50TZ 122-CX221J50TZ 122-CX221J50TZ 122-CX221J50TZ 122-CX103K50TV 122-CX103K50TV 122-CX103K50TV 122-CY106Z10TW 122-CX103K50TV 122-CC104Z16TZ 122-CC104Z16TZ 122-CC104Z16TZ 122-CX221J50TZ 122-CX221J50TZ

Defference

SDM-M51D(E) 5-2
No. # Board Type ! / * Ref. No. A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C034 CAPACITOR 34 A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C043 CAPACITOR 43 A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A CCAPACITOR A C054 CAPACITOR 54 A C055 CAPACITOR 55 A CCAPACITOR A C057 CAPACITOR 57 A C058 CAPACITOR 58

Part No. 1-162-964-11 1-162-964-11 1-162-964-11 1-162-964-11 1-162-964-11 1-162-964-11 1-162-964-11 Pending 1-507-834-31 1-573-792-11 1-793-962-21 1-779-745-21 Pending Pending Pending 1-137-939-11 1-137-939-11 1-137-939-11 1-137-939-11 1-137-939-11 1-807-635-11 1-807-635-11 1-807-635-11 8-719-976-20 1-807-635-11 1-808-077-11 8-719-976-20 8-719-976-20 8-719-902-49
Description CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-X7R 1000PFK 50V CHIP 0603 CAP-EC 47UF 25V 6.3*5.5 SAX PHONE-JACK SCJ356M0NXS0B00 MINI DIN. 4P MH11041-H1 CONN, DVI-I QH11121-CP0 W/HEX 5 MM DC-JACK EIAJ-5 (HEC3900-010110) CONN, 16P 2.0mm JST:S16B-PHDSS CONN, 5P 2.0mm JST:S5B-PH-SM3-TB CONN,41P SMD DF9-41P-1V CAP ARRAY 22PF ISO8P4C 1206 CAP ARRAY 22PF ISO8P4C 1206 CAP ARRAY 22PF ISO8P4C 1206 CAP ARRAY 22PF ISO8P4C 1206 CAP ARRAY 22PF ISO8P4C 1206 DIODE.ZENER RLZ5.1B DIODE.ZENER RLZ5.1B DIODE.ZENER RLZ5.1B DIODE, RLS4148 --LL-34-DIODE.ZENER RLZ5.1B DIODE.SCHOTTKY SB-540 DO-210AD DIODE, RLS4148 --LL-34-DIODE, RLS4148 --LL-34-DIODE, BAV70 SOT-23
Remarks 122-CX102K50TV 122-CX102K50TV 122-CX102K50TV 122-CX102K50TV 122-CX102K50TV 122-CX102K50TV 122-CX102K50TV 162-RV2470M25 203-0235601B 203-0411041 203-11211CP0 203-0139001 197-S16BPHD 197-S5BPHM3 197-DF941P1V 137-010220T 137-010220T 137-010220T 137-010220T 137-010220T 150-RLZ5V1B 150-RLZ5V1B 150-RLZ5V1B 151-RLS4148 150-RLZ5V1B 150-00SB540 151-RLS4148 151-RLS4148 170-BAV70T

SDM-M51D(E) 5-7

No. # Board A 175 A 176 A 177 A 178 A 179 A 180 A 181 A 182 A 183 A 184 A 185 A 186 A 187 A 188 A 189 A 190 A 191 A 192 A 193 A 194 A 195 A 196 A 197 A 198 A 199 A 200 A 201 A 202 A 203
Type DIODE FUSE FUSE FUSE INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
! / * Ref. No. D010 F001 F002 F003 FBA001 FBA002 FBA003 FBA004 FBA005 IC001 IC002 IC003 IC004 IC005 IC005 IC005 IC006 IC007 IC008 IC009 IC010 IC011 IC012 IC013 IC014 IC015 IC016 IC017 IC018
Part No. 8-719-976-20 1-576-491-11 Pending 1-576-491-11 Pending Pending Pending Pending Pending 8-759-426-55 Pending 8-759-478-64 Pending 8-759-712-43 Pending Pending 8-759-011-65 8-759-527-77 8-759-541-69 8-759-442-20 Pending 8-759-582-37 8-759-011-65 8-759-634-77 8-759-467-94 8-759-033-07 8-759-033-19 8-759-998-92 Pending

Description DIODE, RLS4148 --LL-34-Micro Fuse 1.5A --MQ1.5-Micro Fuse 3.0A --MQ3.0-Micro Fuse 1.5A --MQ1.5-BEAD ARRAY N3216A4Z121T01 BEAD ARRAY N3216A4Z121T01 BEAD ARRAY N3216A4Z121T01 BEAD ARRAY N3216A4Z121T01 BEAD ARRAY N3216A4Z121T01 IC CMOS, 74HC4066 SO-14 IC Regulator, SI9181-25 2.5V TSSOP-8 IC, TDA7053A-N2 DIP-16 IC Regulator, SI9181-33 3.3V TSSOP-8 MTV212M PLCC-44 F/W VER: V010 C/S IC, Socket SMD PLCC-44 IC, 74HC4053 SOIC IC, EEPROM M24C16-MN6 SOIC IC, SI786CG SSOP-28 IC, EEPROM 24LC21BT-SN SOIC IC Regulator, SI9181-33 3.3V TSSOP-8 IC Regulator, PQ2TZ15 IC, 74HC4053 SOIC IC, M51951BML -SOT89IC, LM358DT SOIC IC, 74F14 SOIC IC, 74F125 SOIC IC, LM393DT SOIC IC, GM5020 BGA292
Remarks 151-RLS4148 147-BLMQ015 147-BLMQ030 147-BLMQ015 282-1206A4Z121 282-1206A4Z121 282-1206A4Z121 282-1206A4Z121 282-1206A4Z121 160-HC4066T 160-918125T 160-07053A0 160-918133T 160-MTV212M 610-5020V01 197-0448111 160-HC4053T 160-024016T 160-SI786CG 160-024021T 160-918133T 160-PQ2TZ15 160-HC4053T 160-051951T 160-035800T 160-F0140T 160-F1250T 160-039300T 160-005020T

SDM-M51D(E) 5-8

No. # Board A 204 A 205 A 206 No. # Board A 207 A 208 A 209 A 210 A 211 A 212 A 213 A 214 A 215 A 216 A 217 A 218 A 219 A 220 A 221 A 222 A 223 A 224 A 225 A 226 A 227 A 228 A 229 A 230 A 231
Type IC COIL COIL Type COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL
! / * Ref. No. IC019 L001 L002 ! / * Ref. No. L003 L004 L005 L006 L007 L008 L009 L010 L011 L012 L013 L014 L015 L016 L017 L018 L019 L020 L021 L022 L023 L024 L025 L026 L027
Part No. 8-759-442-20 Pending 1-414-183-11 Part No. 1-469-977-11 Pending Pending Pending 1-469-977-11 Pending Pending 1-469-977-11 1-469-977-11 1-469-975-11 1-469-975-11 Pending Pending Pending Pending 1-400-044-11 Pending Pending Pending 1-469-977-11 1-216-296-11 1-469-977-11 1-469-977-11 Pending Pending
Description IC, EEPROM 24LC21BT-SN SOIC FERRITE BEAD, FCM1608K-301T03 INDUCTOR-SMD 10UH CSN043B-100M Description FERRITE BEAD HCB3216K-501T30 FILMAC, BMS200 FILMAC, BMS200 FILMAC, BMS200 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD, FCM1608K-301T03 FILMAC, BMS200 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD, FCM1608K-301T03 INDUCTOR-SMD 15UH CSN105B-150M INDUCTOR-SMD 15UH CSN105B-150M FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 SELMAC, STC104B FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD HCB3216K-501T30 RES, CHIP +-5% 0R 1206 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03

Remarks 160-024021T 143-B1608301 141-3L043100 Remarks 143-NG3216501 280-NGBMS200 280-NGBMS200 280-NGBMS200 143-NG3216501 143-B1608301 280-NGBMS200 143-NG3216501 143-B1608301 141-3L105150 141-3L105150 143-B1608301 143-B1608301 143-B1608301 143-B1608301 280-STC104B 143-B1608301 143-B1608301 143-B1608301 143-NG3216501 100-CR00JT08 143-NG3216501 143-NG3216501 143-B1608301 143-B1608301

SDM-M51D(E) 5-9

No. # Board Type ! / * Ref. No. A LCOIL A LCOIL A LCOIL A LCOIL A L032 COIL 236 A LCOIL A LCOIL A LCOIL A LCOIL A LCOIL A TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA TRANSISTOR QA RRESISTOR A RRESISTOR A RRESISTOR A RRESISTOR A RRESISTOR A RRESISTOR A R007 RESISTOR 256 A R008 RESISTOR 257 A RRESISTOR A R010 RESISTOR 259 A R011 RESISTOR 260
Part No. Pending 1-469-977-11 1-469-977-11 Pending Pending Pending Pending Pending Pending 1-469-977-11 8-729-054-62 8-729-054-62 8-729-054-61 8-729-044-58 8-729-054-61 8-729-054-61 8-729054-60 8-729-054-61 1-216-821-11 1-216-850-11 1-216-841-11 1-216-841-11 1-216-809-11 1-216-809-11 1-216-850-11 1-216-829-11 1-216-809-11 1-216-829-11 1-216-809-11
Description FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD HCB3216K-501T30 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD, FCM1608K-301T03 FERRITE BEAD HCB3216K-501T30 MOSFET-N,SI4808DY SO-8 MOSFET-N,SI4808DY SO-8 TRS,SST3904 T-116 SOT-23 MOSFET-N,SI2304DS SOT-23 TRS,SST3904 T-116 SOT-23 TRS,SST3904 T-116 SOT-23 TRS,SST3906 T-116 SOT-23 TRS,SST3904 T-116 SOT-23 RES,CHIP +-5% 1K 0603 RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 47K 0603 RES,CHIP +-5% 47K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 100R 0603
Remarks 143-B1608301 143-NG3216501 143-NG3216501 143-B1608301 143-B1608301 143-B1608301 143-B1608301 143-B1608301 143-B1608301 143-NG3216501 160-SI4808DY 160-SI4808DY 170-SST3904 160-SI2304DS 170-SST3904 170-SST3904 170-SST3906 170-SST3904 100-C102JT16 100-C274JT16 100-C473JT16 100-C473JT16 100-C101JT16 100-C101JT16 100-C274JT16 100-C472JT16 100-C101JT16 100-C472JT16 100-C101JT16

SDM-M51D(E) 5-10

No. # Board A 261 A 262 A 263 A 264 A 265 A 266 A 267 A 268 A 269 A 270 A 271 A 272 A 273 A 274 A 275 A 276 A 277 A 278 A 279 A 280 A 281 A 282 A 283 A 284 A 285 A 286 A 287 A 288 A 289

Type RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR RESISTOR
! / * Ref. No. R012 R013 R014 R015 R016 R019 R020 R021 R023 R024 R025 R026 R027 R030 R031 R032 R033 R034 R035 R036 R037 R038 R039 R041 R042 R043 R044 R045 R046
Part No. 1-216-821-11 1-216-835-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-833-11 1-216-821-11 1-216-829-11 1-216-850-11 1-216-845-11 1-244-284-11 1-244-284-11 1-216-833-11 1-216-841-11 1-216-833-11 1-216-829-11 1-216-809-11 1-216-850-11 1-216-841-11 1-216-825-11 1-216-829-11 1-216-809-11 1-216-809-11 1-216-801-11 1-216-624-11 1-216-624-11 1-216-624-11 1-216-801-11
Description RES,CHIP +-5% 1K 0603 RES,CHIP +-5% 15K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100K 0603 RES,CHIP +-5% 10K 0603 RES,CHIP +-1% 1K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 100K 0603 RES, CHIP +-5% 0.045R 1206 RES, CHIP +-5% 0.045R 1206 RES,CHIP +-5% 10K 0603 RES,CHIP +-5% 47K 0603 RES,CHIP +-5% 10K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 47K 0603 RES,CHIP +-5% 2.2K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 22R 0603 RES,CHIP +-5% 75R 0603 RES,CHIP +-5% 75R 0603 RES,CHIP +-5% 75R 0603 RES,CHIP +-5% 22R 0603
Remarks 100-C102JT16 100-C153JT16 100-C101JT16 100-C101JT16 100-C101JT16 100-C104JT16 100-C103JT16 100-C1001IT16 100-C472JT16 100-C274JT16 100-C104JT16 100-C457JT08 100-C457JT08 100-C103JT16 100-C473JT16 100-C103JT16 100-C472JT16 100-C101JT16 100-C274JT16 100-C473JT16 100-C222JT16 100-C472JT16 100-C101JT16 100-C101JT16 100-C220JT16 100-C750JT16 100-C750JT16 100-C750JT16 100-C220JT16

SDM-M51D(E) 5-11

No. # Board A 290 A 291 A 292 A 293 A 294 A 295 A 296 A 297 A 298 A 299 A 300 A 301 A 302 A 303 A 304 A 305 A 306 A 307 A 308 A 309 A 310 A 311 A 312 A 313 A 314 A 315 A 316 A 317 A 318
! / * Ref. No. R047 R048 R049 R050 R051 R052 R053 R054 R055 R056 R057 R058 R059 R060 R061 R062 R063 R064 R065 R066 R067 R068 R069 R071 R072 R073 R074 R075 R076
Part No. 1-216-850-11 1-216-850-11 1-216-809-11 1-216-833-11 1-216-829-11 1-216-829-11 1-216-817-11 1-216-817-11 1-216-829-11 1-216-830-11 1-216-829-11 1-216-801-11 1-216-833-11 1-216-833-11 Pending 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-821-11 1-216-821-11 1-216-833-11
Description RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 270K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 10K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 470R 0603 RES,CHIP +-5% 470R 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 5.6K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 22R 0603 RES,CHIP +-5% 10K 0603 RES,CHIP +-5% 10K 0603 FERRITE BEAD, FCM1608K-101T06 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 4.7K 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 100R 0603 RES,CHIP +-5% 1K 0603 RES,CHIP +-5% 1K 0603 RES,CHIP +-5% 10K 0603