2-652-380-11 (1)
To Customers and Sony Dealers

Wall-Mount Bracket

Instructions Mode demploi Instrucciones Gebrauchsanweisung Instructies Istruzioni Instrues Vejledning Bruksanvisning
GB FR ES DE NL IT PT DK SE

SU-WL51

2005 Sony Corporation
01GB01COV.book Page 2 Tuesday, December 20, 2005 4:59 PM
Thank you for purchasing this product.
To Customers Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. Sony is not liable for any damages or injury caused by mishandling or improper installation. Your Statutory Rights (if any) are not affected.

CAUTION

Specified products
The following products might be out of stock or discontinued. Also, some models are not sold in some regions. LCD Color TV / Monitor KDL-40S2000 KDL-40S2010 KLV-40U100M

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire. This instruction manual shows the correct handling of the product and important precautions necessary to prevent accidents. Be sure to read this manual thoroughly and use the product correctly. Keep this manual available for future reference. To Sony dealers Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly to do the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper installation. Please give this manual to the customer after installation.
This Wall-Mount Bracket is designed for use with the specified products above. For other TVs or monitors, refer to their operating instructions to check if this Wall-Mount Bracket can be used. Some TVs or monitors are supplied with a leaflet explaining how to install the Wall-Mount Bracket (Installing the WallMount Bracket).

To Customers

If the following precautions are not observed, serious injury or death through fire, electric shock, the product toppling over, or the product dropping can result.

On Safety

Products by Sony are designed with safety in mind. If the products are used incorrectly, however, it may result in a serious injury through fire, electric shock, the product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such accidents.
Be sure to subcontract the installation to licensed contractors and keep small children away during the installation.
If the Wall-Mount Bracket or the TV or monitor is not installed correctly, the following accidents may occur. Be sure licensed contractors carry out installation. The TV or monitor may fall and cause a serious injury such as a bruise or a fracture. If the wall on which the Wall-Mount Bracket is installed is unstable, uneven, or not perpendicular to the floor, the unit may fall and cause injury or property damage. The wall should be capable of supporting a weight of at least four times the TV or monitor weight. (See the TV or monitor installing dimensions table on page 12 for the weight of each TV or monitor.) If the installation of the Wall-Mount Bracket on the wall is not sufficiently sturdy, the unit may fall and cause injury or property damage.

2 (GB)

SU-WL51 2-652-380-11(1)
01GB01COV.book Page 3 Tuesday, December 20, 2005 4:59 PM
Be sure to subcontract moving or dismounting of the TV or monitor to licensed contractors.
If persons other than licensed contractors transport or dismount the TV or monitor, it may fall and cause injury or property damage. Be sure that two or more persons carry or dismount the TV or monitor.
Do not lean on or hang from the TV or monitor.
Do not lean on or hang from the TV or monitor as it may fall on you and cause serious injury.
Do not spill liquid of any kind on the TV or monitor.
If you allow the TV or monitor to get wet, this may result in a fire or an electric shock.
Do not expose the TV or monitor to rain or moisture.
It may cause a fire or an electric shock.
Do not remove screws, etc., after mounting the TV or monitor.
If you do so, the TV or monitor may fall and cause injury or property damage.
Never place the TV or monitor in hot, humid or excessively dusty places, or in the place where the TV or monitor is subjected to mechanical vibrations.
If you do so, it may cause a fire or an electric shock.
Do not disassemble or make alterations to the parts of the WallMount Bracket.
If you do so, the Wall-Mount Bracket may fall and cause injury or property damage.

Keep flammable objects or open flames (e.g., candles) away from the TV or monitor.
To prevent a fire, keep flammable objects or open flames (e.g., candles) away from the TV or monitor.

GB English

Do not mount any equipment other than the specified product.
This Wall-Mount Bracket is designed for the use with the specified product only. If you mount equipment other than specified, it may fall or break, and cause injury or property damage.
Do not cover the ventilation holes of the TV or monitor.
If you cover the ventilation hole (with a cloth, etc.), heat may build up inside and cause fire.
Do not apply any load other than the TV or monitor on the Wall-Mount Bracket.

3 (GB)

01GB01COV.book Page 4 Tuesday, December 20, 2005 4:59 PM
If the following precautions are not observed, injury or property damage may occur.
Installing the Wall-Mount Bracket

To Sony Dealers

Do not install the Wall-Mount Bracket on wall surfaces where the corners or the sides of the TV or monitor protrude away from the wall surface.
Do not install the Wall-Mount Bracket on wall surfaces such as a pillar, where the corners or the sides of the TV or monitor protrude away from the wall surface. If a person or object happens to hit the protruded corner or side of the TV or monitor, it may cause injury or property damage.
WARNING to Customers Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation. To Sony Dealers The following instructions are for Sony Dealers only. Be sure to read safety precautions described above and pay special attention to safety during the installation, maintenance and checking of this product.
Do not handle the product with excessive force during cleaning or maintenance.
Do not apply excessive force on the topside of the TV or monitor. If you do so, the TV or monitor may fall and cause injury or property damage.
Be sure to install the Wall-Mount Bracket securely to the wall following the instructions in this instruction manual.
If any of the screws are loose or fall out, the Wall-Mount Bracket may fall and cause injury or property damage. Be sure to use the appropriate screws for the material of the wall and install the unit securely, using four or more M8 (or equivalent) screws.

Do not install the TV or monitor over or under an air-conditioner.
If the TV or monitor is exposed to water leaks or air current from an air-conditioner for a long time, it may cause a fire, an electric shock or a malfunction of the TV or monitor.

Precautions

If you use the TV or monitor installed on the Wall-Mount Bracket for a long time, the wall behind or above the TV or monitor may become discolored or the wallpaper may come unstuck, depending on the material of the wall. If the Wall-Mount Bracket is removed after installing it on the wall, the screw holes are left. If you have routed 300-ohm feeder cables behind the wall, we recommend that you change them to 75-ohm coaxial cables. If it is necessary to continue to use 300-ohm feeder cables, be sure there is sufficient space available between the TV or monitor and the feeder cables behind the wall before installing. Consult your licensed contractor regarding an appropriate location (free from radio noise, etc.) before installing.
Be sure to use the supplied screws and attachment parts properly following the instructions given in this instruction manual. If you use substitute items, the TV or monitor may fall, and cause bodily injury to someone or damage to the TV or monitor. Be sure to assemble the bracket properly following the instructed procedure explained in this instruction manual.
If any of the screws are loose or fall out, the TV or monitor may fall, and cause bodily injury to someone or damage to the TV or monitor.

4 (GB)

01GB01COV.book Page 5 Tuesday, December 20, 2005 4:59 PM
Be sure to tighten the screws securely in the designated position.
If you fail to do so, the TV or monitor may fall, and cause bodily injury to someone or damage to the TV or monitor.
Before installation If you intend to install a TV or monitor that is not specified on page 2, be sure to refer to the leaflet Installing the Wall-Mount Bracket supplied with your TV or monitor.
Be careful not to subject the TV or monitor to shock during installation.
If the TV or monitor is exposed to shock, it may fall or break apart. This may cause injury.

Be sure to install the TV or monitor on a wall that is both perpendicular and flat.
If you fail to do so, the TV or monitor may fall and cause injury.
Step 1: Checking the parts required for the installation 1
Prepare four or more M8 or equivalent screws (not supplied) and a screwdriver. Select screws suitable for the material of the wall. Unpack the carton and check to see that all the following items are included.
After proper installation of the TV or monitor, secure the cables properly.
If people or objects get tangled with cables, this may result in injury or damage to the TV or monitor.
Do not allow the AC power cord or the connecting cable to be pinched.
If the AC power cord or the connecting cable is pinched between the unit and the wall or is bent or twisted by force, the internal conductors may become exposed and cause a short circuit or an electrical break. This may cause a fire or an electric shock.
Be careful not to hurt your hands or fingers during the installation.
Be careful not to hurt your hands or fingers when installing the Wall-Mount Bracket or the TV or monitor.

Plate Unit (1)

The screws needed to secure the Wall-Mount Bracket to the wall are not supplied.
Use the appropriate screws for the wall material and structure when mounting the Wall-Mount Bracket.

Mounting Hook Unit (2)

Hook (4)

Screw (+B6 L20) (2)

Paper Template (1)

Screw (+PSW5 L16) (6)

5 (GB)
01GB01COV.book Page 6 Tuesday, December 20, 2005 4:59 PM
Step 2: Deciding on the installation location 1
Referring to the TV or monitor installing dimensions table on page 12 and placing the supplied paper template on a perpendicular and flat wall, decide on the installation location.
Allow for suitable clearance between the TV or monitor and the ceiling and protruding parts of the wall as shown below.

Unit: mm (inches)

Step 3: Installing the Plate Unit on the wall 1
Secure the Plate Unit to the wall using four or more M8 or equivalent screws (not supplied).
Select at least four screw holes with the same mark shown in the diagram below, and tighten the screws securely so that they will not become loose.
Align the unit so that it is exactly level.

100 (4) 100 (4)

300 (11 7/8)

100 (4)

Plate Unit

WARNING Note

If you intend to route the cables in the wall, make a hole in the wall to insert the cables. The position for the cable hole is shown in the diagram on page 13.
Referring to the diagram on page 13, determine the positions of the screws for installing the plate unit. If you intend to route the cables in the wall, also determine the position of the cable hole and bore a hole in the wall.

The screws used in this procedure are not supplied. Select screws suitable for the material and the structure of the wall. If the Plate Unit cannot be attached securely enough, use additional screws. Be sure to confirm that the Plate Unit is securely attached to the wall.
The wall that the TV or monitor will be installed on should be able to support a weight of at least four times that of the TV or monitor (page 12). Make sure of the strength of the wall the TV or monitor will be installed on. Reinforce the wall sufficiently, if necessary.

6 (GB)

01GB01COV.book Page 7 Tuesday, December 20, 2005 4:59 PM
Adjust the angle of the arms.
When installing the TV or monitor perpendicularly (0 degrees), adjustment of the arm angle (procedures 1 and 2 below) is not necessary. Make sure that each arm base is screwed in securely. 1 Remove the screws from the top and bottom centre of the both arm bases. Then choose the notch corresponding to the desired angle (5, 10, 15 or 20 degrees) and fit each arm base to them. If you are installing the KLV-40U100M, do not choose the notch for 20 degrees. 2 Firmly secure each arm base using the screws removed in the above procedure 1.
Notes Be sure to adjust the angles of the right and left arms to the same angle. Be careful not to pinch your fingers when adjusting the angle of the arms. When using an electric screwdriver, set the torque setting to approximately 2 Nm {20 Kgfcm}. Make sure that the two arm bases are screwed in securely. Notes on the adjustment angles
Change the position of the Mounting Hook Unit support shafts.
1 Remove the screws securing the both left and right Mounting Hook Unit support shafts, and then move the Mounting Hook Unit support shafts to the inner position. Make sure the marks on the both Mounting Hook Unit support shafts align with the F marks on the plate unit. 2 Secure the Mounting Hook Unit support shafts using the screws from procedure 1.
Mounting Hook Unit support shaft
When installing TV or monitor models other than those specified on page 2 (depending on the model's size and dimensions, etc.), the adjustment angles listed (0, 5, 10, 15, 20 degrees) for the arms may be limited. For the available adjustment angles of the arms when installing TV or monitor models other than those specified on page 2, refer to the operating instructions or the leaflet (Installing the WallMount Bracket) supplied with the TV or monitor.

0 degrees: Leave the white screws tightened as they are. Other than 0 degrees: Remove the white screws.
When using an electric screwdriver, set the torque setting to approximately 2 Nm {20 Kgfcm}. Make sure that the two Mounting Hook Unit support shafts are screwed in securely.

Arm base

7 (GB)
01GB01COV.book Page 8 Tuesday, December 20, 2005 4:59 PM
Step 4: Preparing for the installation of the TV or monitor
The procedure differs depending on the TV or monitor. Apply the procedure appropriate for the TV or monitor you are installing.
KDL-40S2000/KDL-40S2010. A KLV-40U100M.. B
If you intend to install a TV or monitor that is not specified on above, be sure to refer to the leaflet Installing the WallMount Bracket supplied with your TV or monitor.
Detach the Table-Top Stand from the TV or monitor. A
Remove the screws from the rear side of the TV or monitor. A
Attach the supplied four hooks on the rear side of the TV or monitor.
Place the TV or monitor with its screen facing down on a stable cloth-covered work surface. Attach the supplied four hooks with the four supplied screws (+PSW5 L16).
Remove the eight screws from these eight holes in the rear side of the monitor.

Soft cloth

Align the hook with the circle on the rear side of the TV or monitor.
Notes When using an electric screwdriver, set the torque setting to approximately 2 Nm {20 Kgfcm}. Be sure not to use any screws other than the supplied ones (+PSW5 L16) when attaching the hooks.

8 (GB)

01GB01COV.book Page 9 Tuesday, December 20, 2005 4:59 PM
Step 5: Installing the TV or monitor on the Plate Unit
If you intend to install a TV or monitor that is not specified on page 2, be sure to refer to the leaflet Installing the WallMount Bracket supplied with your TV or monitor.
Connect the AC power cord and the connecting cable(s) supplied with the TV or monitor to the TV or monitor.
Connect the AC power cord and the connecting cable(s) to the connectors on the rear side of the TV or monitor. For details on connecting the AC power cord and the connecting cable(s), refer to the instruction manual of the TV or monitor. When you route the cord and the cable in the wall, feed them through the bored hole (page 13).

Notes You cannot connect the cables to the TV or monitor after installing it on the Plate Unit. Subcontract the cable routing in the wall to licensed contractors.
Be sure to complete the installation before connecting the AC power cord to the wall outlet. If you allow the AC power cord to be pinched under or between pieces of equipment, this may result in a short circuit or an electric shock. Be careful not to stumble over the AC power cord or the TV or monitor, as you may hurt yourself.
Attach the Mounting Hook Units on the hooks on the rear side of the TV or monitor. Then slide the Mounting Hook Units, as illustrated below, and secure them using the supplied screws (+PSW5 L16).
Rear side of the TV or monitor
Note Be sure not to use any screws other than the supplied ones (+PSW5 L16) when securing the Mounting Hook Units.

(Continued) 9 (GB)

01GB01COV.book Page 10 Tuesday, December 20, 2005 4:59 PM
Step 5: Installing the TV or monitor on the Plate Unit (Continued)
6 Firmly tighten the securing screws screwed in temporarily in procedure 1.
Install the TV or monitor onto the Plate Unit.
1 Insert the screws (+B6L20, supplied) into the screw holes on the outer left and right sides of the Mounting Hook Unit support shafts, and tighten them temporarily.
Be sure to tighten both left and right securing screws firmly. If you fail to do so, the TV or monitor may fall when it is pushed upward and cause injury.
Tighten the screws to halfway so that they do not protrude from the opposite side.
Confirming the completion of the installation
Check the following points.
The eight hooks of the Mounting Hook Units are firmly hooked on the four shafts of the Plate Unit. The cord and the cable are not twisted or pinched. The two securing screws on the Mounting Hook Unit are securely tightened.
Note If the temporarily attached screws protrude inside the Mounting Hook Unit support shafts, the lower hooks of the Mounting Hook Unit cannot be fitted in (procedure 4).
2 Hitch the upper hooks of the two Mounting Hook Units on to the support shafts of the arms. 3 Place the lower hooks of the two Mounting Hook Units so that they touch the front side of the Mounting Hook Unit support shafts. 4 Slightly push the TV or monitor toward the Plate Unit and upward, to hitch the lower hooks of the two Mounting Hook Units to the Mounting Hook Unit support shafts. 5 Confirm the eight hooks are firmly hooked on the four shafts on the Plate Unit.
Incomplete installation may cause the product falling and result in injury or product damage. Also, improper placement of the AC power cord, etc., may cause fire or electric shock through a short circuit. Be sure to confirm the completion of the installation for safety.

Mounting Hook Units

10 (GB)
01GB01COV.book Page 11 Tuesday, December 20, 2005 4:59 PM
When removing the TV or monitor

Specifications

Unit: mm (inches) Weight: 9.5 kg (21 lb) Plate Unit 670 (26 3/8) 54 (2 1/8)
Unplug the AC power cord from the wall outlet. Remove the two securing screws on the right and left Mounting Hook Unit support shafts. Be sure that two or more persons hold the TV or monitor and slide it upward to remove the TV or monitor.
Mounting Hook Unit 51 (2)
Be sure that two or more persons hold the TV or monitor when carrying it. Be careful not to allow the cord and cables to get hung up when removing the TV or monitor. Be careful not to hurt your hands or fingers when removing the TV or monitor.
Design and specifications are subject to change without notice.

388 (15 9/32)

420 (16 17/32)

11 (GB)

01GB01COV.book Page 12 Tuesday, December 20, 2005 4:59 PM
TV or monitor installing dimensions table
The table below shows dimensions of the TV or monitor that is mounted on this product. Refer to this table to decide on the installation location. If you intend to install a TV or monitor that is not specified on page 2, be sure to refer to the leaflet Installing the Wall-Mount Bracket supplied with your TV or monitor. KDL-40S2000/KDL-40S2010

Screen centre line

KLV-40U100M
Display Dimensions (0) Display Model A B C
Length for each mounting angle Mounting angle ( ) F G

393 (15 15/32)

Unit: mm (inches) H

Weight

KDL-40S2000/ KDL-40S2010

988 (39) 989 (39)

664 (26 1/4) 653 (25 3/4)

103 (4 1/8) 127 (5)

288 (11 3/8) 199 (7 7/8)

83 (3 3/8) 160 (6 3/8)

161 (6 3/8) 336 (13 1/4) 185 (7 3/8) 288 (11 3/8)
188 (7 1/2) 132 (5 1/4) 100 (4) 63 (2 1/2)
83 (3 3/8) 115 (4 5/8) 160 (6 3/8) 190 (7 1/2)
21 kg 84 kg (46 lb 5 oz) (185 lb 4 oz) 25 kg 100 kg (55 lb 2 oz) (220 lb 8 oz)
Figures in the above table may differ slightly depending on the installation. * The wall that the TV or monitor will be installed on should be capable of supporting a weight of at least four times that of the TV or monitor.

12 (GB)

01GB01COV.book Page 13 Tuesday, December 20, 2005 4:59 PM
Wall processing dimensions diagram
Unit: mm (inches) 670 (26 3/8) 610 (24) 455 (17 29/32) 406 (16)
131 (5 5/32) 65.5 (2 37/64) 60 (2 23/64) Hole for cable routing Slot hole 13.5 (17/32) 20 - (23/64 5/6) 131 (5 5/32)

2-652-380-11(1)

393 0.5 (15 15/32 5/256)

131 (5 5/32)

13 (GB)
Nous vous remercions davoir fait lacquisition de ce produit.
lattention des clients Une certaine exprience est requise pour installer ce produit. Veillez confier linstallation des revendeurs Sony ou des installateurs agrs et portez une attention particulire aux consignes de scurit pendant linstallation. Sony ne saurait tre tenue responsable de tout dommage ou de toute blessure dcoulant dune mauvaise utilisation ou dune installation incorrecte. Vos droits lgaux (ventuels) ne sont pas affects.

KDL-46V2500

Key Features 16:9 Native 1080p HD Resolution Panel (1920 x 1080) 7000:1 Dynamic Contrast Ratio with ACE1 BRAVIA ENGINE Full Digital Video Processor Live Color Creation featuring WCG-CCFL backlight HDMI (High Definition Multimedia Interface) x2 (1080p) 16:9 Native 1080p HD Resolution Panel (1920 x 1080) 7000:1 Dynamic Contrast Ratio with ACE

BRAVIA LCD Television

BRAVIA ENGINE Full Digital Video Processor Live Color Creation featuring WCG-CCFL backlighting system HDMI (High Definition Multimedia Interface) x2 (1080p) Key Technologies
1920 x 1080 Panel Resolution When it comes to high-definition TV the pinnacle of performance is achieved by using 1920 x 1080
display panels. And BRAVIA V-Series televisions have them. Full HD 1920 x 1080 panel resolution with over 2 million pixels (more than twice that of 720p HDTV) is exactly what you need to reproduce the 1080p content that can be delivered by our cutting edge 1080p Bluray disc player. And working with BRAVIA Engine standard definition is upconverted to 1080p for a picture so real its like youre actually there.
Advanced Contrast Enhancer (ACE) Function Sonys Advanced Contrast Enhancer (ACE) builds on our excellent on-contrast
ratio performance. A Dynamic Contrast Ratio of up to 7000:11 is achieved by using real-time image processing to adjust the contrast along with optimizing backlight levels. But rather than focus on the "numbers", Sony focuses on actual picture performance avoiding exaggerated blacks where detail can be lost. ACE translates to blacker blacks in darker scenes, as well as better shadow detail in other scenes for a difference that you can see.
Full HD 1080 There are a lot of ways to define high-definition but BRAVIA Full HD means youre getting the best resolution that highdefinition has to offer consumers. With Sony BRAVIA V-Series HDTVs, Full HD 1080 means 1920 x 1080 pixels and 1080p video inputs. Your lifestyle demands the best in high-definition and with BRAVIA Full HD 1080 products you get it.
BRAVIA Engine Full Digital Video Processor BRAVIA V-Series LCD televisions use Sony's BRAVIA Engine full digital video
processor for crisp and clear images. Several special picture enhancement technologies are integrated into the processor to create better gradations and details, enhance contrast, dynamically improve color, and reduce image flicker.
Live Color Creation System Decades of television know how allow us to realize that an LCD TV is more than just the panel; its
actually a system. Uncompromised picture quality starts with combining carefully chosen components and circuits to optimize system quality, among these are the color creation and processing functions. Thats what Live Color Creation is all about. It starts with the BRAVIA Engine PRO video processing system, which enhances primary colors and corrects half-tone colors for natural overall color. Next, a WCG-CCFL backlight using Sonys phosphor formula delivers a specific spectrum of light designed to work with our specially formulated color filters. The combination of these three components creates deep, deep blues and natural greens for overall colors that draw you right into the picture itself.

HDMI and PC Connectivity Designed for maximum versatility, Sonys BRAVIA V-Series LCD TVs are equipped with a
comprehensive range of input interfaces. The HDMI (High-Definition Multimedia Interface) is the first industry-supported, uncompressed, all-digital audio/video interface. HDMI technology supports enhanced or High Definition video, together with multi-channel digital audio to provide matchless image and sound reproduction. BRAVIA V-Series TVs include (2) HDMI 1080/60p inputs. The PC input (HD15-pin) offers easy connection to your PC, allowing you to use your high resolution BRAVIA V-Series Digital TV as a computer monitor.

Features

General
Video Label: Yes Closed Captions (CC): Yes On-Screen Display: Menu

Inputs and Outputs

Component Video (Y/Pb/Pr ) Input(s): 2 (Rear) Composite Video Input(s): 3 (2 Rear/1 Side) Digital Audio Output(s): 1 (Rear) RF Connection Input(s): 1 (Rear) S-Video Input(s): 2 (1 Rear/1 Side) Headphone Output(s): 1 (Side) PC Audio Input(s): 1 (Rear) PC Video Input(s): 1 (Rear)4 Analog Audio Input(s) (Total): 5 (4 Rear/1 Side) Audio Out: 1 (Rear) HDMI Connection(s) (Total): 2 (Rear) HDMI Connection(s) (w/ Analog Audio In): 1 with L/R RCA audio connections
Video Processing: Yes (BRAVIA Engine System) Noise Reduction: Yes CineMotion Reverse 3:2 Pulldown Technology: Yes Picture Modes: Vivid, Standard, Custom Display Technology: LCD (178 wide viewing angle LCD display panels) High Definition: Yes (Full HD 1080) 3D Comb Filter: Yes Live Color Creation Technology: Yes
Power Consumption (in Standby): Less than 0.1W
MTS Stereo Decoder: Yes A/V Synch: Off/1/2/3 Digital Amplifier: Yes SRS TruSurround XT Audio Effect: Yes Auto SAP: Yes Steady Sound Automatic Volume Control: Yes Dolby: Dolby Digital (AC3/ATSC only) Audio Mode: Dynamic, Custom, Standard SRS: SRS TruSurround XT Audio Effect
Regulation and Standard Compliance
Energy Star Compliant: Yes VESA Hole Spacing Compatible: Yes VESA Hole Pitch: 200 x 200 hole pattern / M6 thread size / 14mm hole depth
Service and Warranty Information
Limited Warranty: 1 Year Parts / 1 Year Labor

Convenience

Channel Label: Yes Channel Skip/Add: Yes Favorite Channel: Yes Parental Control (V-Chip): Yes Sleep Timer: 15, 30, 45, 60, 90, Off Timer Events: Timer 1, Timer 2 Clock: Yes Power Save Mode: Standard, Reduced, Picture Off Picture Freeze: Yes Input Skip: Yes Remote Control: Yes LightSensor : Yes

Dimensions

Weight: 70.55lbs (32.0kg) with pedestal; 57.32lbs (26.0kg) without pedestal

Supplied Accessories

Remote Control (RM-YD012) Pedestal (swivel) Batteries (AA x2) HD-15 to HD-15 cable Operating Instructions Quick Setup Guide

Optional Accessories

Wall-Mount Bracket (SU-WL51) Color: Black UPC Code: 027242696129
1. Black-white range seen at the same time. 2. Black-white range seen over a period of time. 3. Screen Size measured diagonally. 4. Limited to resolutions supported by both the PC and the Sony TV. See Sony TV users manual and PC documentation for supported resolutions 2006 Sony Electronics Inc. All rights reserved Sony, BRAVIA, BRAVIA Engine, DRC, Speed Surf, and CineMotion are trademarks of Sony. SRS and the SRS symbol, TruSurround are trademarks of SRS Labs, Inc. Dolby Digital is a registered trademark of Dolby Laboratories. This TV incorporates High-Definition Multimedia Interface (HDMI ) technology. HDMI, the HMDI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. All other trademarks are property of their respective owners. Features and specifications are subject to change without notice. Nonmetric weights and measures are approximate. Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities CA 92127 800.222.7669 www.sony.comor the Electronic Industries Alliance (www.eiae.org)

Specifications

Aspect Ratio: 16:9 Television Type: Flat Panel LCD HDTV
Audio Power Output: 20W (10w x2)

Timer Clock: Yes

Please visit the Dealer Network for current information at www.sony.com/dn Last Updated: 05/23/2008
Sony Electronics Inc. 16530 Via Esprillo San Diego,