Sony TA-FB940R Manual
Sony TA-FB940r Home Cinema Amplifier, size: 491 KB
Sony TA-FB940r Annexe 1
Sony TA-FB940r Service Manual
Here you can find all about Sony TA-FB940R like manual and other informations. For example: review.
Sony TA-FB940R manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Sony TA-FB940R please write about it to help other people. [ Report abuse or wrong photo | Share your Sony TA-FB940R photo ]
User reviews and opinions
|Kellinom||10:22pm on Sunday, September 12th, 2010|
|Great little amp if you can afford to leave it on. i used this with an old pair of dm330i that are very sensitive and the 60w rms was plenty.|
|cburley||9:57pm on Wednesday, March 17th, 2010|
|This is a beast! Had this for several years, I used to power a pair of hefy AE120 floorstanding speakers with them.|
Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.
Integrated Stereo Amplifier
Operating Instructions Mode demploi Manual de instrucciones Manual de instrues
GB FR ES PT
2000 Sony Corporation
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
On the prevention of howling
Do not disassemble the cabinet as this may result in an electrical shock. Refer servicing to qualified personnel only. Should any solid object or liquid fall into the cabinet, unplug the amplifier and have it checked by qualified personnel before operating it any further.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Do the following: lower the volume. keep the turntable as far from the speakers as possible. use commercially available audio insulators on the bottom of the turntable. keep the microphone away from the speakers during use. For further protection against howling, set the speakers or turntable on top of a heavy wooden board or concrete slab. If you have any questions or problems concerning your amplifier, please consult your nearest Sony dealer.
On power sources
Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.
Before operating the amplifier, check that the operating voltage of the amplifier is identical with your local power supply. The operating voltage is indicated on the nameplate at the rear of the amplifier. If you are not going to use the amplifier for a long time, be sure to disconnect the amplifier from the wall outlet. To disconnect the AC power cord (mains lead), grasp the plug itself; never pull the cord. AC power cord must be changed only at the qualified service shop.
Place the amplifier in a location with adequate ventilation to prevent heat built-up and prolong the life of the amplifier. Do not place the amplifier near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. Do not place anything on top of the cabinet that might block the ventilation holes and cause malfunctions.
Before connecting other components, be sure to turn off and unplug the amplifier.
On cleaning the amplifier
Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.
Thank you for purchasing the Sony Integrated Stereo Amplifier. Before operating the amplifier, please read this manual thoroughly and retain it for future reference.
TABLE OF CONTENTS
Hookup Overview 4 Audio Component Hookups 4 Speaker System Hookups 5 Mains Lead Hookups 6
About This Manual
The instructions in this manual are for models TA-FB940R and TA-FB740R. Check your model number by looking at the rear panel of your amplifier. The TA-FB940R is the model used for illustration purposes unless stated otherwise. Any difference in operation is clearly indicated in the text, for example, TA-FB940R only.
Listening to the Music 7 Recording 9 Additional Information
Troubleshooting 10 Specifications 10 Rear Panel Descriptions 11 Remote Button Descriptions 11
Instructions in this manual describe the controls on the amplifier. For details on the remote buttons control, see Remote Button Descriptions on page 11. The following icon is used in this manual:
Check that you have received the following supplied items: Remote commander (remote) (1) RM-S336 Sony batteries R6 (size-AA) (2)
Indicates hints and tips for making the task easier.
Inserting batteries into the remote
Insert two R6 (size-AA) batteries, matching the + and on the batteries with the markings inside the battery compartment. When using the remote, point it at the remote control sensor g on the amplifier.
When to replace batteries
With normal use, the batteries should last for about 6 months. When the remote no longer operates the amplifier, replace all the batteries.
Do not leave the remote near an extremely hot or humid place. Do not drop any foreign object into the remote casing, particularly when replacing the batteries. Do not expose the remote sensor to direct sunlight or lighting equipment. Doing so may cause a malfunction. If you dont use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion.
The amplifier allows you to connect and control the following audio components. Follow the hookup procedure indicated for each component that you want to connect. To learn the location and name of each jack, see Rear Panel Descriptions on page 11.
Audio Component Hookups
Here you learn how to connect your audio components to the amplifier.
IMPEDANCE USE 416 A+B USE 816 BI WIRE USE 416
DAT deck MD deck
Tape deck Turntable
Tuner SACD CD player
EON CONTROL A
R IN IN
R IN REC OUT IN REC OUT IN
TAPE2/MD EON CONTROL IN
EON LINK TAPE1/DAT TAPE2/MD AUX SACD/CD TUNER PHONO
What cords will I need?
TAPE MONITOR SOURCE DIRECT 0 10
SOURCE ON OFF ON OFF TAPE1 TAPE2
Audio connecting cord (not supplied) (2 for each tape deck, DAT deck, or MD deck; 1 for other components)
TV or video deck
Before you get started
Turn off the power to all components before making any connections. Do not connect the mains leads of the various components until all connections are completed. Use the audio connecting cords supplied with each component for hooking up with the amplifier. Purchase and use optionally available cords as required. Be sure to make connections firmly to prevent hum and noise. When connecting an audio connecting cord, be sure to match the R (right) and L (left) jacks of the amplifier to the R and L jacks on the other components.
White (L) Speaker (R) Red (R)
White (L) Red (R)
The arrow indicates signal flow. SACD/CD player
Amplifier SACD/CD player
Tape deck, DAT deck, or MD deck
Speaker System Hookups
OUT IN TAPE1/DAT
Here you learn how to connect speakers to the amplifier. You can connect two pairs of speakers, SPEAKERS A and B. Note that the SPEAKERS A terminals comprise the bottom row of the SPEAKERS terminals.
SPEAKERS A SPEAKERS B
Use the configuration above to connect the OUTPUT and INPUT jacks of: a tape deck or DAT deck to the TAPE1/DAT jacks. a tape deck or MD deck to the TAPE2/MD jacks.
PHONO IN L
Speaker cord (not supplied) (1 for each speaker)
To prevent hum, connect the earth lead to SIGNAL GND (y) on the amplifier.
IN AUX OUTPUT
Twist the stripped ends of the cord about 10 mm. Be sure to match the speaker cord to the appropriate terminal on the components: + to + and to. If the cords are reversed, the sound will be distorted and will lack bass.
If your tuner is equipped with an EON CONTROL OUT terminal, connect it to the EON CONTROL IN terminal on the amplifier to allow use of the EON (Enhanced Other Networks) function of the RDS (Radio Data System) (see page 8).
Connecting to bi-wire system speakers
Since the two pairs of speaker terminals on your amplifier, SPEAKERS A and B, can provide simultaneous speaker output, you can use them to connect a bi-wire speaker system. To drive both speaker systems simultaneously, set SPEAKERS to A+B. To select the speaker system A or B
Set SPEAKERS to A or B. To drive both speaker systems simultaneously, set SPEAKERS to A+B.
Mains Lead Hookups
Connecting the mains lead
Connect the mains lead from this amplifier and from your audio/video components to wall outlets.
You can power other components through AC OUTLET on the amplifier
By connecting other audio components to AC OUTLET on the amplifier, you can supply power to the connected components through the amplifier and turn them all on or off when you turn the amplifier on or off.
Use speakers with a nominal impedance of 4 to 16 ohms. When outputting at the same time to two speaker systems, use speakers with a nominal impedance of 8 to 16 ohms.
Make sure that the total power consumption of all components connected to the outlets on the amplifier does not exceed 100 watts. Do not connect electrical home appliances such as an electric iron, fan, TV, or other highwattage appliances to these outlets.
Separate the mains lead, audio connecting cords and speaker cords. Noise or sound deterioration may occur when audio connecting cords are in contact with the mains lead, or when the mains lead or speaker cords are placed near the tuners loop aerial or aerial wire.
Listening to the Music
INPUT SELECTOR VOLUME
SACD/CD AUX TUNER
TAPE1/DAT EON LINK
A OFF A+B B
TAPE MONITOR SOURCE DIRECT
PHONES TAPE1 SOURCE
SOURCE DIRECT 0 10
To listen through the headphones
Connect the headphones to PHONES and set SPEAKERS to OFF.
To listen directly to the input signal
Press SOURCE DIRECT so that the indicator lights up. Since the circuits of TONE controls, BALANCE control, LOUDNESS button, and SUBSONIC button are bypassed, you cannot adjust bass, treble, the balance, reinforce the bass and treble, or reduce subsonic noise components while listening to a source directly.
Avoid high speaker output at which the sound is distorted. High-frequency distortion may damage the tweeters.
Press POWER to turn on the amplifier and turn VOLUME fully anticlockwise to prevent damaging the speakers with excessive output. The PROTECTION indicator lights up, then goes off. Turn on the programme source you want to listen to.
Set INPUT SELECTOR to the respective programme source. The indicator for the programme source lights up.
To listen to a
Record Radio broadcast Compact disc or SACD Source connected to AUX Source connected to: TAPE1/DAT TAPE2/MD
Turn INPUT SELECTOR for
PHONO TUNER SACD/CD AUX TAPE1/DAT TAPE2/MD
Start the programme source.
Adjust the volume by turning VOLUME.
Press or turn
BASS TREBLE BALANCE LOUDNESS SUBSONIC
Adjust the bass Adjust the treble Adjust the balance Reinforce the bass and treble at low listening level Reduce subsonic noise components created by warped records, etc.
What is the Enhanced Other Networks (EON)?
One convenient RDS service is Enhanced Other Networks (or EON). This allows the unit to automatically switch to a programme type of your choice when one starts in your broadcast area.
To receive the Enhanced Other Networks (EON) programmes
When your amplifier is connected to a Sony tuner with the EON CONTROL system, the amplifier switches to any EON programme that is broadcast in your EON area, and switches back to the last selected programme source when the programme ends. TA-FB940R
Make sure that the amplifier and the tuner are connected through the EON CONTROL terminals (see page 5). Press EON LINK so that the indicator lights up. Whenever an EON programme starts on the radio frequency that your tuner is set to, you will receive it.
To cancel EON reception
Press EON LINK again so that the indicator goes off.
If you select another programme source while receiving an EON programme, EON reception ends. However, as long as the EON LINK indicator lights up, you can receive EON programmes automatically. Make sure to cancel EON reception before starting to record since an EON programme may interfere with your recording. If you activate the Tape Monitor function (see page 9) while the EON LINK indicator is lit, the indicator goes off and you cannot receive EON programmes. If this happens, deactivate the Tape Monitor function so that the indicator lights up again.
TAPE1/DAT TAPE2/MD AUX SACD/CD TUNER PHONO SPEAKERS
You can record the same source on two recording components at the same time You can monitor the recorded sound (Tape Monitor function)
You can monitor the recorded sound if the tape deck you are recording on has separate playback and recording heads. To monitor the sound, set TAPE MONITOR to TAPE1 or TAPE2. Note that on the TA-FB740R, you can monitor the only sound being recorded from the TAPE1/DAT jacks.
Before you begin recording, press the EON LINK button to turn off the EON LINK indicator (see page 8).
Press POWER to turn on the amplifier.
Turn on the programme source you want to record.
Select the programme source that you want to record by turning INPUT SELECTOR. The indicator for the programme source lights up.
To record a
Set INPUT SELECTOR to
Prepare the recording component for recording, then start recording. Start playing the programme source.
If you experience any of the following difficulties while using the amplifier, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. No sound output.
/ Connect the audio connecting cords firmly. / Connect the amplifier and other audio components correctly. / Turn INPUT SELECTOR to the appropriate programme source. / Make sure the speaker wires are correctly connected to the SPEAKERS A terminals (on the bottom row) and SPEAKERS B terminals (on the top row). / Make sure the proper selection is made on the SPEAKERS control (A, B, A+B, or OFF).
DIN power output
TA-FB940R: 120 W + 120 W (4 ohms at 1 kHz) 80 W + 80 W (8 ohms at 1 kHz) TA-FB740R: 100 W + 100 W (4 ohms at 1 kHz) 60 W + 60 W (8 ohms at 1 kHz)
Total harmonic distortion
Less than 0.008% (at 10 W output 1 kHz)
PHONO (20 Hz - 20 kHz): RIAA equalization curve 0.5 dB TUNER, SACD/CD, AUX, TAPE1/DAT, TAPE2/MD: 7 Hz - 300 kHz+0 dB 3
S/N (network A)
No audio from one channel or unbalanced speaker output.
/ Turn BALANCE to adjust the balance. / Check the speaker and input connections of silent channel.
PHONO TA-FB940R: 94 dB TA-FB740R: 90 dB TUNER, SACD/CD, AUX, TAPE1/DAT, TAPE2/MD: 105 dB
Weak bass or treble.
/ Adjust the TONE controls. / Change speaker positions or room conditions to eliminate obstructions in sound path.
REC OUT 1, 2: 150 mV, 1 kilohm PHONES: 10 mW (at 8 ohms)
4 - 16 ohms, 8 - 16 ohms (SPEAKERS A+B)
/ Improperly selected input signal. / Insufficient input capacity of speakers. Lower the volume.
500 (8 ohms, 1 kHz)
Lack of bass or ambiguity in instrument positions.
/ Speaker cord and terminal polarity are reversed. Reconnect the cords with correct polarity.
Hum or noise.
/ Ground the turntable system (see page 5). / Connect the audio connecting cords firmly. / The amplifier is picking up interference from a TV set. Move the amplifier away from the TV set or turn the TV set off.
Power amplifier: Pure-complementary SEPP OCL power amplifier with all stages directly coupled Preamplifier: Low-noise, equalizer amplifier
230 V AC, 50/60 Hz
TA-FB940R: 210 W TA-FB740R: 180 W
Dimensions (approx.) (w/h/d)
The remote does not function.
/ Remove any obstructions between the remote control sensor on the amplifier and the remote. / Point the remote towards the remote sensor on the front of the amplifier. / The remote is too far from the amplifier. Move closer to the amplifier. / Replace the batteries in the remote. TA-FB940R: 420 mm TA-FB740R: 420 mm incl. projecting parts and controls
TA-FB940R: 10.3 kg TA-FB740R: 8.6 kg
The PROTECTION indicator lights up and/or sudden loss of audio.
TH-42PX8BA TX-NR900E HF-300 KV-29CS60B TX100 Truck VSX-32 M1717A-BZ Review PM-T990 37ET-35S Adventure SCX-4720FN Ow 5000 CD2502S 53 AH215-JD LFX23961ST CDR560-00S Casio DA-7 Management PD125 Precision 530 CT-S510 KX-T9000BS Essentials 3 Es20 TX-SR503 TX-SR574 GT-9800F Amilo Asko 1402 DVD-7880K Vapeur AG-HPG20 CDP-CE315 GPS 100 Pltv-27M ST-61 Readimanagerse200 Ericsson T300 HDR-CX520VE DR-550mkii DAV-DX250 TH-42PA60E Sedan 11 CH-X500 WD-8050FH KIP 3000 EC990SW Fostex D-90 Radio Sdvic IPS33B P2770HD Nanopad LBE 129 EL-546W 601-602-604 HT-BD1220 KM-5530 Sport NWZ-A846 ES-TG55G AWM 129 Hblg1004R WF0602nuwg 3X10W NV-A1 Hmnc096D4A0 85099 GR-409GLQ FRS 104 Calybox 20 PSR-125 URC22D-8B GL350SB RX-6010vbkj-RX-6010 E821 ST AVH-5200DVD EL-531RH CE283GN Canon S5IS 50PX4R LBP5100 Seiko 7019 SGH-F200 AQ09FAN DCR-HC90 DM1200 Odelia 753 FE-100 425618X51 C-MAX AJ3540 WRT54G2 DV-HRD1 KEH-P7100RDS PZ42X 85544 MFC-3100C SP-URC-81-ME
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101