PCG-R505JE/R505JEK/R505JEP/R505JL/ R505JLK/R505JLP/R505JS/R505JSK/R505JSP

SERVICE MANUAL

Ver. 1-2001J Revision History is appended to the end of this manual.

For American Area

US Model Canadian Model

Update

Lineup: PCG-R505JE PCG-R505JEK PCG-R505JEP PCG-R505JL PCG-R505JL/C PCG-R505JLK PCG-R505JLP PCG-R505JS PCG-R505JSK PCG-R505JSP

en id f

l ia t

Notebook Computer

9-872-269-01
Information in this document is subject to change without notice.
Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack of equipment or in both the operating and the service instructions. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions. CAUTION: The battery pack used in this device may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100C (212F) or incinerate. Dispose of used battery promptly. Keep away from children. CAUTION: Changing the back up battery. Overcharging, short circuiting, reverse charging, multilation or incineration of the cells must bi avoided to prevent one or more of the following occurrences; release of toxic materials, release of hydrogen and/or oxygen gas, rise in surface temperature. If a cell has leaked or vented, it should be replaced immediately while avoiding to touch it without any protection.
Sony and VAIO are trademarks of Sony. Microsoft, MS-DOS, Windows, the Windows 95, Windows 98, Windows 2000, Windows ME and Windows XP logo are trademarks of Microsoft Corporation. All other trademarks are trademarks or registered trademarks of their respective owners. Other trademarks and trade names may be used in this document to refer to the entitles claiming the marks and names or their produces. Sony Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas requiring special precautions. Be sure to observe these precautions, as well as all precautions listed in the operating manual and other associated documents. After servicing, inspect to make sure that all screws, components, and wiring have been returned to their original condition. Also check the area around the repair location to ensure that repair work has caused no damage, and confirm safety.
5. When replacing chip components.
Never reuse components. Also remember that the negative side of tantalum capacitors is easily damaged by heat.
2. Use designated parts only
The sets components possess important safety characteristics, such as noncombustibility and the ability to tolerate large voltages. Be sure that replacement parts possess the same safety characteristics as the originals. Also remember that the 0 mark, which appears in circuit diagrams and parts lists, denotes components that have particularly important safety functions; be extra sure to use only the designated components.
6. When handling flexible print boards.
The temperature of the soldering-iron tip should be about 270C. Do not apply the tip more than three times to the same pattern. Handle patterns with care; never apply force.
3. Always follow the original design when mounting parts and routing wires
The original layout includes various safety features, such as inclusion of insulating materials (tubes and tape) and the mounting of parts above the printer board. In addition, internal wiring has been routed and clamped so as to keep it away from hot or high-voltage parts. When mounting parts or routing wires, therefore, be sure to duplicate the original layout.
Caution: Remember that hard disk drives are easily damaged by vibration. Always handle with care.
4. Inspect after completing service

Confidential

PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)

TABLE OF CONTENTS

Section 1-1. 1-2. 1-3. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19.

CHAPTER 1. REMOVAL

Flowchart... 1-1 Main Electrical Parts Location Diagram.. 1-2 Removal... 1-2 Key Board Unit... 1-2 Palm Rest Section.. 1-3 SWX-72 Board, Encoder (Rotaly), Touch Pad. 1-3 IFX-141 Board... 1-4 Battery... 1-4 HDD... 1-5 Cover (Bottom LF/LR/R).. 1-5 Frame Housing... 1-6 SWX-76 Board, Speaker (L/R).. 1-6 CNX-119 Board... 1-7 Modem Card... 1-7 CNX-121 Board... 1-8 DC Fan.... 1-8 MBX-48 Board... 1-9 Heatsink (CPU)... 1-9 CNX-120 Board, LCD Section, CNX-131 Board. 1-10 Bezel... 1-11 LCD Unit... 1-11 LEX-29 Board, Inverter Unit... 1-12 (to 1-12)
CHAPTER 2. SELF DIAGNOSTICS. 2-1
Please confirm Self Diagnostics method which will be informed you with distribution of Self Diagnostics software.
CHAPTER 3. BLOCK DIAGRAM. 3-1

(to 3-2)

CHAPTER 4. FRAME HARNESS DIAGRAM. 4-1

(to 4-2)

CHAPTER 5. EXPLODED VIEWS AND PARTS LIST
5-1. Main Section... 5-2 5-2. LCD Section... 5-5 5-3. Accessories... 5-7 (to 5-7)
Abbreviations UC : US model / Canadian model

Confidential 3

CHAPTER 1. REMOVAL 1-1. Flowchart
POWER OFF KEY BOARD UNIT P 1-2 COVER (BOTTOM LF/ LR/R) P 1-5 FRAME HOUSING P 1-6 SPEAKER (L/R) P 1-6 SWX-76 BOARD P 1-6 SWX-72 BOARD P 1-3 ENCODER (ROTARY) P 1-3 TOUCH PAD P 1-3 BATTERY P 1-4 PALM REST SECTION P 1-3 IFX-141 BOARD P 1-4 HDD P 1-5 CNX-120 BOARD P 1-10 LCD SECTION P 1-10 CNX-131 BOARD P 1-10 BEZEL P 1-11 LCD UNIT P 1-11 LEX-29 BOARD P 1-12 INVERTER UNIT P 1-12 CNX-119 BOARD P 1-7 MODEM CARD P 1-7 CNX-121 BOARD P 1-8 DC FAN P 1-8 MBX-48 BOARD P 1-9 HEATSINK (CPU) P 1-9
P XX means pages that appears in this manual. Remember that hard disk drives are easily damaged by vibration. Always handle with care.
1-1 PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)
1-2. Main Electrical Parts Location Diagram
CNX-131 Board LEX-29 Board Speaker (L) LCD Unit Inverter Unit
CNX-121 Board DC Fan MBX-45 Board IFX-141 Board Modem Card

SWX-76 Board

Speaker (R) Battery Encoder (Rotary) SWX-72 Board HDD CNX-119 Board Touch Pad

1-3. Removal

1. Key Board Unit

Key Board Unit

2 Claw

4 Harness Claw

PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-2

1 M2X6

2. Palm Rest Section

Palm Rest Section

3 Flexible Flat Cable (10 core)
3. SWX-72 Board, Encoder (Rotaly), Touch Pad
7 Claw 8 Escutcheon (TP) Claw 7 Claw Touch Pad 2 Flexible Flat Cable (12 core) 7 Claw
Encoder (Rotary) 5 M1.4X3.Flexible Flat Cable (10 core) 3 M2X4 SWX-72 Board

4. IFX-141 Board

IFX-141 Board
4 M2XFlexible Flat Cable (12 core)

3 Cover (Bottom LF)

5. Battery
1 Harness Nickel Hydrogen Battery
PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-4

6. HDD

4 M3XFPC (HDD) 5 Bracket (HDD R)

2 M2X4

7 Bracket (HDD F) 6 M3X4 3
HDD 30 GB (PCG-R505JS, R505JSK, R505JSP) HDD 20 GB (PCG-R505JE, R505JEK, R505JEP) HDD 15 GB (PCG-R505JL, R505JL/C, R505JLK, R505JLP)
7. Cover (Bottom LF/LR/R)
Cover (Bottom LR) 3 Claw 3 Claw Cover (Bottom LF)

Claw 6

Cover (Bottom R) Assy

5 Claw

1-5 PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)

8. Frame Housing

1 Harness 3 Undo four claws and remove the cover (BP). 2 Flexible Flat Cable (8 core) 4 M2X6

Frame Housing

3 Undo four claws and remove the cover (BP).
9. SWX-76 Board, Speaker (L/R)
Button (Power) Speaker (L) 8 Speaker Bracket 2 Tapping 2XHarness SWX-76 Board 1 Flexible Flat Cable (8 core) Speaker (R) 6 Speaker Bracket
PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-6

10. CNX-119 Board

3 Flexible Flat Cable (NI Shield) 20P

1 M2X4 CNX-119 Board

11. Modem Card

1 M2X2.5

2 Connector 1 M2X2.5

Modem Card

4 Harness (2P) 3
1-7 PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)

12. CNX-121 Board

1 M2XShield CNXFlexible Flat Cable (10 core) CNX-121 Board

13. DC Fan

2 M2X6 DC Fan (With Heatsink) 1 Harness

2 M2X6

PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-8

14. MBX-48 Board

5 M2XM2XShield MBXHarness (Power 3P) 1 Harness (LCD) 5 M2XSpacer (MBX) 0 RJ-45 (For Internal) Harness 3 Harness

7 M2X3.Flexible Flat Cable (NI Shield) 20P 9 qa Lid (VGA) Assy

5 M2X4

MBX-48 Board

15. Heatsink (CPU)

Heatsink (CPU) * The heatsink (CPU) must be installed with the thermal sheet (CPU) in soft state to protect the CPU from the stress. For this purpose, with the thermal sheet (CPU) pasted, warm the heatsink (CPU) to about 70 C, and when the thermal sheet (CPU) has become soft, install the heatsink (CPU) on the main board.

1 P2X3

3 Bracket (CPU)
1-9 PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)
16. CNX-120 Board, LCD Section, CNX-131 Board

LCD Section

3 Harness (2P)

6 M2X5

1 M2X5
CNX-120 Board 7 M2X4 CNX-131 Board 0 Harness (Power 3P) qa qd Cover (BBL) 9

5 M2X5 qs Cover (BBR)

4 Harness (LCD)

8 M2X4

PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-10

17. Bezel

4 M2XHole Blind (Side)

5 Claw Claw

2 Cover (DL)
3 Hole Blind (Side) 4 M2XClaw
5 Claw Housing (Bezel) Assy 1 Cover (DR)

18. LCD Unit

3 Harness (LCD)
7 Bracket (LCD-L) 6 M2X3 2
4 M2X3 LCD Unit 5 Bracket (LCD-R) 1 Harness
19. LEX-29 Board, Inverter Unit

3 Harness 5 Harness

1 M2X3

LEX-29 Board

Inverter Unit 6 Harness
PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 1-12 (END)
CHAPTER 2. SELF DIAGNOSTICS
< ATTENTION > Please confirm Self Diagnostics method which will be informed you with distribution of Self Diagnostics software.
2-1 (END) PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)

CHAPTER 3. BLOCK DIAGRAM

Copper mine Copperwith Processor Core mine 256/ ProcessorL2 Cache 256/ 128KB Core with 128KB L2 Cache BGA2 BGA2

CLKGEN IMI C9835

12 XGA LCD & INVERTER

Docking Station

CPU Local Bus

100MHz Memory Bus

Refer to Clock Generator Block Diagram

LCD CONN

DC-IN CONN
Display Display Cash Cash
On Board Memory Graphics & Memory Graphics & Memory CONTROLLER CONTROLLER HUB HUB GMC H2-m GMCH2-m 1,2 Bus #0 Dev #0,

ROW#2 ,3

SO-DIMM VCH VCH Cable VGA DB-15

USB CONN

ROW#0 ,1

VGA DB-15

RJ11 i.LINK

DVO(3.3V)

FDD x1

MS CONN Internal HDD

Memory USB2 Memory Stick Stick Mod ule Mod ule Cable( Primary IDE)
IO Control Hub IO Control Hub ICH2-m ICH2-m Bus #0 Dev #8,31

EEPROM EEPROM For LAN

Et her Ether PHY PHY PCI-1394 PCI-1394 TI TI TSB43LV22 TSB43LV22

EEPROM EEPROM For i.LINK

LAN-A1

Port Connector 100+4pin

i.LINK0

PCI BUS(3.3V)

CardBus/16b itCard CARDBUS CARDBUS RICOH RICOH RC5C475II RC5C475II PC Card Connector 1 Slot

i.LINK0 i.LINK1

Bus #1 Dev #8

Bus #1 Dev # 12

Seri al

Serialx1 Printerx1

AC LINK
EEPROM EEPROM For Password

Paral lele

FWH FWH (Flash BIOS ROM) (Flash BIOS ROM)
Super I/O Super SMsC I/O SMsC LPC47N227 Audio Audio AD1881A AD1881A

Headphone

LPC47N227
H8S/2149 H8S/2149 KBC/EC KBC/EC SPIC SPIC
I/O Expander I/O Exp MUX & SM BUSander & SM BUS MUX
FAN BATTERY USB3 USB1 USB(A) CONN x1 USB(B) CONN x1

LAN-A0

Speaker
Parallele i.LINK1 FDD SWX- 72 Bo ard JOG JOG Contro ller Contro ller

BAT CONN

BATTERY
POWER SUPPLY & CHARGE R
MDC (ModemMDC Daughter (Modem Da ghter Card) u Card) Mod ule Mod ule
i.LINK i.LINK PHY & PHY ATAPI & ATAPI Bridge Bridge

i.LINK

Membr ane

PHONE OUT

MIC IN

Speaker L&R

is can not connect on main unit when connected dockin g stataion

TouchP ad KeyBoard

CD-ROM/ RW/DVD
3-1 3-2 (END) PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)
CHAPTER 4. FRAME HARNESS DIAGRAM

CN4901

LEX-29 BOARD SIDE A
FROM board connector (direct connection) Harness (connector at both end) Harness (soldered at one end)

INVERTER UNIT

HARNESS (LCD)
Side L CNX-131 BOARD SIDE A

CN4401 DC IN 1

DOCKING STATION PCGA-DSD5/DSM5 EXTENSION MEMORY MODULE PCGA-MM64N/MM128N /MM256N

LITHIUM ION BATTERY PACK

CN2702
CN2004 CN8 FCC (8P) 2 CN8 8

CN4402 3

SWX-76 BOARD SIDE B

S4801 POWER CN1

HARNESS (POWER 3P)

SPEAKER R ch

RJ-45 HARNESS (FOR INTERNAL)

Side R

CNX-121 BOARD SIDE B

CN4302 USB

DC FAN (WITH HEATSINK)

CN2801

NETWORK

CNX-120 BOARD SIDE B

CN30 J29

SPEAKER L ch

CN5001 MODULAR JACK

CN1 CNCNCN1 2

MODEM CARD

1 CN5002

HARNESS (2 PIN)

FCC (10P)

KEY BOARD

MBX-48 BOARD SIDE A

CN1 CNCN702 EXT. DISPLAY 50 FPC (HDD) CN2201

PC CARD CONNECTOR

CN1202

PC CARD

CN1301 i.LINK

NICKEL HYDROGEN BATTERY

CN2802 1

CN2003 10

HDD PCG-R505JL, R505JL/C, R505JLK, R505JLP : 15GB PCG-R505JE, R505JEK, R505JEP: 20GB PCG-R505JS, R505JSK, R505JSP: 30GB

CNX-119 BOARD SIDE B

CNCN4002 MIC/LINE INPUT CN4003 HEAD POHNE CN4004 USB
FLEXIBLE FLAT CABLE (NI SHIELD) 20P 1 CN10 CN4702

FCC (10P) FCC (12P)

MEMORY STICK

CN4502 1

IFX-141 BOARD SIDE A

CN4501 12

FLEXIBLE FLAT CABLE (12 CORE)
S4703 LEFT BUTTON S4701 ENCODER (ROTALY)

SWX-72 BOARD SIDE A

S4702 CENTER BUTTON S4704 RIGHT BUTTON

TOUCH PAD

4-1 4-2 (END) PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)
The mechanical parts with no reference number in the exploded views are not supplied. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. When the same reference numbers are written down in the list, please use the one listed in the first place as the main part.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

5-1 PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)

5-1. Main Section

Ref.No. 31 * 32 * 34 Part No. A-8066-926-A 1-757-785-11 1-476-060-32 4-652-922-03 4-652-940-02 4-652-921-04 4-652-920-04 4-652-935-02 4-652-907-03 4-652-944-01 4-659-257-01 X-4624-418-1 4-652-923-03 4-653-410-01 1-772-529-61 1-790-729-11 4-653-370-01 1-757-787-12 1-544-847-11 4-653-371-01 A-8066-928-A 4-653-372-01 4-652-919-01 1-544-846-11 X-4623-665-6 4-652-913-02 1-476-671-22 1-763-688-11 1-815-304-11 4-654-327-01 4-653-411-02 4-652-932-01 4-652-924-01 A-8058-454-A Description COMPLETE PWB SWX-72 FLEXIBLE FLAT CABLE (10 CORE) ENCODER (ROTARY) BRACKET (JOG) DETECTOR, LATCH BUTTON (PAD) R BUTTON (PAD) L LENS (PALM REST) HOUSING (PALM REST) COVER, LENS COVER (BOTTOM LF) COVER (BOTTOM LR) ASSY ESCUTCHEON (PAD) INSULATOR (PAD) PAD, TOUCH CABLE, FLEXIBLE FLAT (12 CORE) BRACKET, SPEAKER FLEXIBLE FLAT CABLE (8 CORE) SPEAKER (16MM, WITH HARNESS) R CUSHION, SPEAKER COMPLETE PWB SWX-76 CUSHION BUTTON PW BUTTON (PW) SPEAKER (16MM, WITH HARNESS) L HOUSING (FRAME) ASSY COVER (BP) KEY BOARD UNIT (US) FAN, DC (WITH HEATSINK) CONNECTOR, PC CARD 1 SLOT SHEET (GMCH), THERMAL Ref.No. B1 B2 B3 B5 B6 B7 B8 B9 B10 B11 B12 B14 Part No. X-4623-610-1 A-8066-941-A 1-757-786-11 4-641-449-01 X-4624-332-1 4-652-918-01 X-4624-331-1 4-654-610-03 1-756-038-21 1-961-147-11 A-8066-938-A 1-757-784-11 4-653-716-01 1-757-792-11 A-8066-942-A A-8066-933-A 4-653-432-01 4-654-326-01 4-654-384-01 4-654-450-02 4-654-382-01 4-654-518-02 4-653-506-02 4-654-517-02 4-654-239-01 Description HOUSING (BOTTOM) ASSY COMPLETE PWB CNX-119 FLEXIBLE FLAT CABLE (NI SHIELD) 20P FOOT (F) COVER (BOTTOM R) ASSY LID (ETHER) LID (VGA) ASSY COVER AIR DUCT BATTERY, NICKEL HYDROGEN HARNESS (POWER 3PIN) COMPLETE PWB IFX-141 FLEXIBLE FLAT CABLE (12 CORE) SPRING (BT), COMPRESSION COIL FLEXIBLE FLAT CABLE (10 CORE) COMPLETE PWB CNX-121 COMPLETE PWB CNX-131 CLAMP SHEET (CPU), THERMAL GND GASKET 5X15X1 SHEET (COVER LR) CUSHION HDD CONNECTOR SHIELD CNX 1 SHEET (MODEM) SHIELD MBX 1 INSULATING SHEET

4-657-622-01 FOOT (R2) 8-749-019-00 (R505JL/C, R505JS, R505JSK, R505JSP).IC HYM71V16M655AT6-P 1-695-514-21 JACK (SMALL TYPE) 1P (HEAD PHONE) 1-793-100-11 CONNECTOR, USB 1-779-745-31 JACK, DC 1-793-430-11 4-656-224-01 4-657-779-01 4-657-623-01 4-644-492-31 3-930-461-01 4-644-492-01 4-648-320-01 4-635-966-01 4-645-016-31 3-713-786-51 4-651-989-11 4-635-301-01 4-654-273-01 4-644-492-51 JACK, SMALL TYPE (MIC) SPACER PC CARD FRAME SPACER (PALM REST) CUSHION (COVER LR) ACE (M2), LOCK (2X4) SCREW (DIA. 1.4X3.5), PRECISION ACE (M2), LOCK (2X6) TAPPING (M2) (2X4) SCREW (HEX) ACE (M2) (DIA. 4.6), LOCK (2X2.5) SCREW +P 2X3 SPACER (MBX) SCREW M3X4 ACE (M2), LOCK (2X5) ACE (M2) (DIA. 4.6), LOCK (2X3.5)
SHEET (PC CARD), INSULATING HEATSINK BRACKET (VGA) (R505JL, R505JL/C, R505JLK, R505JLP).MBX-48 (P750) (S) A-8058-453-A (R505JE, R505JEK, R505JEP, R505JS, R505JSK, R505JSP).MBX-48 (P850-A) (S) 4-652-925-01 1-960-827-31 1-761-380-23 4-653-412-01 1-961-140-11 X-4623-577-4 4-652-941-03 A-8058-459-A 4-652-942-03 1-790-750-13 BRACKET (CPU) HARNESS (2 PIN) CARD, MODEM SHEET (BOTTOM), INSULATING HARNESS, RJ-45 (FOR INTERNAL) LID (DOG) ASSY COVER (BBL) CNX-120 (COM) (S) COVER (BBR) FPC (HDD)

* * * 47

4-645-016-11 ACE (M2) (DIA. 4.6), LOCK (2X3.5)
4-652-927-01 BRACKET (HDD R) 1-796-206-11 (R505JS, R505JSK, R505JSP). ASSY HDD 30GB (TO, 15, F) (S) 1-796-272-11 (R505JE, R505JEK, R505JEP). ASSY HDD 20GB (TO) (S) 1-796-162-21 (R505JL, R505JL/C, R505JLK, R505JLP).ASSY HDD 15GB (T, 15B) (S) 4-652-926-01 BRACKET (HDD F)
To paste the thermal sheet (CPU) (65) to the heatsink (CPU), warm the thermal sheet (CPU) adequately until it becomes soft. For further information, refer to the removal (page 1-9).
PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 5-2
28 wf wf BH wa 1 B1 B11 B6 qh 42 F B11 P 21 E B5 ws A qa 8 wa BB1 BB2 A B1 qs B12 B 80 B3 B3 B4 qd 55 B3 qf 51 B1 qd B1 K 6 w; qg 52 L qs ql qk w; 9 wj 45 B68 qj B1 wh ws 16 C I qh D E 58 N qa O BJ wd wg 7 B2 G 39 qk B12 qf 69 qj BI ql 38 B J 35 L wg 9 qg 74 K B1 B3 B12 N M H 32 wd C O B1 F B12 B9 D G B7 Bwh B3 BB1 wj 31 B7 P 7 M B1 B3

5-2. LCD Section

Ref.No. 107 * 114 * 115

B4 B13

Part No. X-4623-574-4 4-652-902-01 4-652-933-01 4-652-934-01 4-652-938-01 4-652-904-03 4-639-623-11 4-652-898-01 A-8058-456-A 4-652-900-02 X-4623-573-1 4-652-901-03 1-476-317-12 A-8066-930-A 4-652-899-01 1-961-063-11 4-652-903-01 4-657-053-01 4-657-053-11 4-657-053-21 4-657-053-31 4-657-053-41 4-657-053-51 4-657-053-61 4-657-053-71 4-657-053-81 4-659-345-01 4-643-356-01 4-645-016-01
Description HOUSING (BEZEL) ASSY COVER (DL) BLIND (SIDE), HOLE BLIND (LCD), HOLE CUSHION (LATCH) LATCH SPRING (LATCH), COIL BRACKET (LCDL) LCD (12.1) (H) (S) TILT UNIT (L) HOUSING (DISPLAY) ASSY TILT UNIT (R) INVERTER UNIT COMPLETE PWB LEX-29 BRACKET (LCDR) HARNESS, LCD COVER (DR) (R505JSP).LABEL (ID) (U) (R505JSK).LABEL (ID) (U) (R505JS).LABEL (ID) (U) (R505JEP).LABEL (ID) (U) (R505JEK).LABEL (ID) (U) (R505JE).LABEL (ID) (U) (R505JLP).LABEL (ID) (U) (R505JLK).LABEL (ID) (U) (R505JL).LABEL (ID) (U) (R505JL/C).LABEL (ID) (U) SCREW (M2X5) ACE (M2) (DIA. 4.6), LOCK (2X3)

B107 B4 BB A

BB B116 1

119 117

PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) 5-5 5-6

5-3. Accessories

201 Power Cord

Ref.No. Part No.

Description ACCESSORIES ***********
1-757-562-21 CORD, POWER 1-756-152-31 BATTERY PACK, LITHIUM ION (L) 1-476-342-22 ADAPTOR, AC 4-658-992-01 QUICK START, R505 SERIES LOOK AT EXPLODED VIEWS OF THE PART **********************************

203 Battery Pack

208 208
(R505JL, R505JLK, R505JLP). PCGA-DSD5 (R505JL/C, R505JS, R505JSK, R505JSP).PCGA-DSM5

204 AC Adaptor

208 Docking Station (PCGA-DSD5: R505JL, R505JLK, R505JLP) (PCGA-DSM5: R505JL/C, R505JS, R505JSK, R505JSP)
* The main unit is not assigned with a part number. Refer to the PCGA-DSD5/DSM5 Service Manual (9-872-201-11).
5-7 (END) PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM)
PCG-R505JE/R505JEK/R505JEP/R505JL/R505JLK/ R505JLP/R505JS/R505JSK/R505JSP (AM) List of PCG-R505 Series for American Area (As of October, 2001)
PCG-R505TE PCG-R505TEK PCG-R505TS PCG-R505TSK PCG-R505DE PCG-R505TL PCG-R505TLK PCG-R505JE PCG-R505JEK PCG-R505JEP PCG-R505JL PCG-R505JLK PCG-R505JLP PCG-R505JS PCG-R505JSK PCG-R505JSP

Service Manual Parts No.

9-872-185-11 9-872-220-11 9-872-242-11
: Additional Model American Area : North, Central and South Americas
This manual and the constituent data may not be replicated, copied nor reprinted in whole or in part without prior written authorization of Sony Corporation.

Sony Corporation

English 2001J0500-1