XM-SD22X

SERVICE MANUAL

Ver. 1.0 2004.12
US Model Canadian Model AEP Model UK Model E Model

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS (US MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 200 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.1% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications
OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Suitable speaker impedance (stereo) (when used as a bridging amplifier) Maximum outputs 400 W 2 (at 4 ) 600 W 2 (at 2 ) 1,200 W (BTL, at 4 ) Rated outputs (supply voltage at 14.4 V) 200 W RMS 2 (20 Hz 20 kHz, 0.1% THD + N, at 4 ) 250 W RMS 2 (20 Hz 20 kHz, 0.15% THD + N, at 2 ) 500 W RMS (BTL) (20 Hz 20 kHz, 0.15% THD + N, at 4 ) SN Ratio 93 dBA (Reference 1W into 4 ) Frequency response 5 Hz 50 kHz ( +0 dB) 3 Circuit system Input level adjustment range 0.3 6.0 V (RCA pin jacks) 1.2 12.0 V (High level input) Low-pass filter Hz, 12 dB/oct Low boost dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.V Current drain at rated output : 48 A (at 4 ) Remote input : 1 mA Dimensions Approx. 277 mm (15 7/1/in.) (w/h/d) not incl. projecting parts and controls Mass Approx. 5 kg (11 lb. 1 oz.) not incl. accessories Supplied accessories Mounting screws (4) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice.

STEREO POWER AMPLIFIER

9-879-367-01

2004L04-1 2004.12

Sony Corporation
e Vehicle Company Published by Sony Engineering Corporation
Note for Replacement of FET Change the both channels of FETs at the output stage. If one or both parts in the following combination is broken, the service kit should be ordered. Service kit part No. Q108, 110, 112 X-3383-027-1 Q208, 210, 212 Q109, 111, 113 X-3383-028-1 Q209, 211, 213
TABLE OF CONTENTS 1. GENERAL
Location and Function of Controls.. 3 Connections.... 4

2. DISASSEMBLY

2-1. 2-2. 2-3. 2-4. Bottom Plate.. 7 Main Board Section.. 8 Main Board... 8 LED Board... 9
3. ELECTRICAL ADJUSTMENT. 10 4. DIAGRAMS
4-1. 4-2. 4-3. 4-4. Block Diagram... 11 Schematic Diagram Main Section (1/2). 12 Schematic Diagram Main Section (2/2). 13 Printed Wiring Boards Main Section.. 14

5. EXPLODED VIEWS

5-1. Heat Sink (Main) Section.. 16 5-2. Main Board Section... 17
6. ELECTRICAL PARTS LIST... 18
Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.

Frequency/Frquence

Cut-off frequency (LPF) Frquence de coupure (LPF)
-10 -20 -30 -40 -50 -60 -70 -100 1k

50Hz 300Hz 170Hz

Location and Function of Controls
Hz 1 PROTECTOR indicator When the PROTECTOR is activated, the indicator lights up in red. When the PROTECTOR is activated refer to the Troubleshooting Guide. 2 LEVEL adjustment control The input level can be adjusted with this control. Turn it in the clockwise direction when the output level of the car audio unit seemslow. 3 LOW BOOST level control Turn this control to boost the frequencies around 40 Hz to a maximum of 10 dB. 4 Cut-off frequency adjustment control Setsthe cut-off frequency (Hz) for the low-pass filter. 5 FILTER selector switch When the switch is in the LPF position, the filter is set to low-pass.
Emplacement et fonction des commandes
1 Indicateur PROTECTOR Lorsque PROTECTOR est activ, lindicateur sallume en rouge. Lorsque PROTECTOR est activ, reportezvous au guide de dpannage. 2 Commande de rglage LEVEL Le niveau dentre peut se rgler avec cette commande. Tournez cette commande dans le sens des aiguilles dune montre lorsque le niveau de sortie de lautoradio semble faible. 3 Commande de niveau LOW BOOST Tournez cette commande pour amplifier les frquences autour de 40 Hz jusqu un maximum de 10 dB. 4 Commandes de rglage de la frquence de coupure Permet de rgler la frquence de coupure (Hz) pour le filtre passe-bas. 5 Slecteur FILTER Lorsque le slecteur est en position LPF, le filtre est rgl sur passe-bas.
Circuit Diagram Schma du circuit

Normal Power AMP Lch

(BTL.)

LOW BOOST

Power AMP

Inverted

PROTECTOR

LOW BOOST (40Hz)

FILTER

Connections

Caution
Before making any connections, disconnect the ground terminal of the car battery to avoid short circuits. Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. Do not connect the # terminal of the speaker system to the car chassis, and do not connect the # terminal of the right speaker with that of the left speaker. Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the speaker cords supplied with the car. If your car is equipped with a computer system for navigation or some other purpose, do not remove the ground wire from the car battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected.

For details on the settings of switches and controls, refer to Location and Function of Controls. Note Make sure that the line output from the car audio unit is connected to the jack marked L (BTL) on the unit.
Pour plus de dtails sur les rglages des commutateurs et commandes, reportez-vous Emplacement et fonction des commandes. Remarque Vrifiez que la sortie de ligne de lautoradio est raccorde la prise portant lindication L (BTL) sur lappareil.
Power Connection Wires Cbles dalimentation
As the Monaural Amplifier for a Subwoofer Comme amplificateur monaural pour un haut-parleur dextrmes graves
to a metal point of the car vers une partie mtallique de la carrosserie
less than 450 mm (18 in) moins de 450 mm (18 po)

OFF LPF

Remote output *1 Sortie de commande *1 (REM OUT)
Fuse (80 A) Fusible (80 A) +12 V car battery Batterie de voiture +12 V Subwoofer (min. 4 ) Haut-parleur dextrmes graves (min. 4 )

Car audio unit Autoradio

*1 If you have the factory original or some other car audio unit without a remote output for the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. *1 Si vous disposez du modle dorigine ou dun autre autoradio sans aucune sortie de commande distance pour lamplificateur, raccordez la borne dentre de la commande distance (REMOTE) la prise dalimentation accessoires.
For details on the settings of switches and controls, refer to Location and Function of Controls. Note If you wish to use a subwoofer as a monaural speaker, connect the speaker as illustrated above. The output signals to the subwoofer will be the combination of the both right and left output signals.
Pour plus de dtails sur les rglages des commutateurs et commandes, reportez-vous Emplacement et fonction des commandes. Remarque Si vous dsirez utiliser un haut-parleur dextrmes graves comme haut-parleur monaural, raccordez le haut-parleur comme illustr ci-dessus. Les signaux de sortie vers le haut-parleur dextrmes graves seront une combinaison des signaux de sortie droit et gauche.
Notes on the power supply Connect the +12 V power supply wire only after all the other wires have been connected. Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier. Be sure to connect the remote control wire of the car audio unit to the remote terminal. When using a car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessorypower supply. Use the power supply wire with a fuse attached (80 A). All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post, and before they pass through any metal. Make sure that the vehicles battery wires connected to the vehicle (ground to chassis) *2 are of a wire gauge at least equal to that of the main power wire connected from the battery to the amplifier. Make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 4-Gauge (AWG-4) or have a sectional area of more than 22.0 mm 2 ( 7/8 in 2).

Full range speakers (min. 2 ) Haut-parleurs gamme tendue (min. 2 ) Subwoofers (min. 2 ) Haut-parleur dextrmes graves (min. 2 )
High Level Input Connection (As a Monaural Amplifier for a Subwoofer) Connexion dentre haut niveau
(Comme amplificateur monaural pour un haut-parleur dextrmes graves)
Left speaker Haut-parleur gauche
For details on the settings of switches and controls, refer to Location and Function of Controls. Note In this system, the volume of the subwoofers will be controlled by the car audio unit fader control.
Pour plus de dtails sur les rglages des commutateurs et commandes, reportez-vous Emplacement et fonction des commandes. Remarque Dans ce systme, le volume des haut-parleurs dextrmes graves est contrl par la commande de balance avant/arrire de lautoradio.
Car audio unit Autoradio Right speaker Haut-parleur droit
Subwoofer (min. 4 ) Haut-parleur dextrmes graves (min. 4 )
For details on the settings of switches and controls, refer to Location and Function of Controls. Note If you wish to use a subwoofer as a monaural speaker, connect the speaker as illustrated above. The output signals to the subwoofer will be the combination of both right and left output signals.
High Level Input Connection (2-Speaker System) Connexion dentre haut niveau

(Systme 2 haut-parleurs)

White Blanc
Left speaker output Sortie haut-parleur gauche
Black-striped cord Cordon ray noir

Grey Gris

Right speaker output Sortie haut-parleur droit
For details on the settings of switches and controls, refer to Location and Function of Controls.
Pour plus de dtails sur les rglages des commutateurs et commandes, reportez-vous Emplacement et fonction des commandes.
High Level Input Connection (As a Monaural Amplifier) Connexion dentre haut niveau
(Comme amplificateur monaural)
Left speaker (min. 4 ) Haut-parleur gauche (min. 4 )
Right speaker (min. 4 ) Haut-parleur droit (min. 4 )
* High Level Input Connector * Connecteur dentre haut niveau
Grey/Black striped Gris/Ray noir
White/Black striped Blanc/Ray noir
XM-SD22X SECTION 2 DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET 2-1. BOTTOM PLATE (Page 7) MAIN BOARD SECTION (Page 8)

MAIN BOARD (Page 8)

LED BOARD (Page 9)
Note : Follow the disassembly procedure in the numerical order given.

2-1. BOTTOM PLATE

2 two screws (+BTP 3 x 6) 1 two screws (+BTP 3 x 6)

4 bottom plate

5 insulating sheet 3 two screws (+BTP 3 x 6)

2-2. MAIN BOARD SECTION

4 screw (+P 3 x 8) 3 three screws (+P 3 x 8) 2 three screws (+P 3 x 8)

5 MAIN board section

1 four screws (+P 3 x 8)

heat sink (main)

6 CN810

2-3. MAIN BOARD

4 MAIN board
2 three screws (+P 3 x 8)

3 front panel

1 two screws (+P 3 x 8)

2-4. LED BOARD

1 three screws (+P 3 x 8) 2 bracket (LED) 3 LED board
XM-SD22X SECTION 3 ELECTRICAL ADJUSTMENT

Bias Adjustment

Note : In Bias Adjustment, adjust RV103 if any of Q108 through Q113 are replaced. Adjust RV203 if any of Q208 through Q213 are replaced. Condition : This adjustment should be performed about one minute after the remote mode is turned on at a room temperature of about 25C. Setting :

B+, REM terminal

set Stabilized Power supply GND terminal
Procedure : 1. Turn the variable resistors RV103 (L-CH) and RV203 (R-CH) full clockwise as seen from the component side to minimize the bias current. 2. The input signal is to be no signal. 3. Apply the voltage to the B+ and REM terminals from the stabilized power supply and gradually increase it up to 12.0 V while checking for any unusual current. 4. Adjust each of RV103 (L-CH) and RV203 (R-CH) so that the power current of the stabilized power supply is increased in steps of 700 mA (total of 1.4 A). 5. After adjustment, check that the power current is at 1.65 to 2.05 A.
Adjustment Location : Main board (component side)
MAIN BOARD (CONDUCTOR SIDE)
RV103 BIAS ADJUSTMENT (L-CH)
RV203 BIAS ADJUSTMENT (R-CH)
XM-SD22X SECTION 4 DIAGRAMS

4-1. BLOCK DIAGRAM

PRE AMP IC101 (1/2) S801-1 FILTER OFF LPF 6 L.P.F IC301 RV101-1 LEVEL 1 RV301-1 FILTER RV301-2 FILTER INV. AMP IC302 (2/2) CNJ801-2,-4 -2 PRE AMP IC101 (2/2) PRE AMP IC202 (1/2) S801-2 FILTER OFF RV101-2 LEVEL LPF 1 LOW BOOST IC202 (2/2) LINE SWITCH QRV102-1 LOW BOOST (40Hz) 5 L.P.F IC302 (1/2) 7 BOOST EQUALIZER Q101 16.7V (B-) DIFFERENTIAL AMP Q104 DRIVE AMP Q106 BIAS Q107

L (BTL)

CNJ801-1,-3 -1 INPUT

PRE AMP IC102 (1/2) 2

LOW BOOST IC102 (2/2)

LINE SWITCH Q102 7

OUTPUT (THROUGH) -3 CNJ803 L

DIFFERENTIAL AMP Q103

DRIVE AMP Q105 RV103 BIAS

POWER AMP Q108,Q110,Q112

CN804 BTL L

+16.7V (B+)

HIGH LEVEL INPUT R

OVER CURRENT DET Q114

POWER AMP Q109,Q111,Q113

SPEAKER OUT

OUTPUT (THROUGH) R INPUT

DIFFERENTIAL AMP Q203

DRIVE AMP Q205 RV203 BIAS BIAS Q207

POWER AMP Q208,Q210,Q212

CNBTL 2 R
+16.7V (B+) BOOST EQUALIZER Q201 DIFFERENTIAL AMP Q204

OVER CURRENT DET Q214

RV102-2 LOW BOOST (40Hz)
16.7V (B-) LINE SWITCH CONTROL Q701,702

DRIVE AMP Q206

POWER AMP Q209,Q211,Q213
DC OFFSET DET Q802,Q803,Q804
CN801 REM POWER ON/OFF Q903 DC DET IC902 F902 +12V GND F901 B+ SWITCH Q901,QD850,852 (POWER) D851,853 (POWER) PROTECT LATCH Q801,Q805,Q806 D854 PROTECTOR 14 TEMP.DET Q809 TH801,803,808 PTH801 D820,822,827,2 +45V (B+) -45V (B-) DRIVER Q911 SWITCHING DRIVER Q907,Q908,Q909 REF. REG SWITCHING Q913 RECT D910 RECT D912,918 B-REG Q915 RECT D906 D920 54V (B) -45V (B-) 10 DRIVER Q910 SWITCHING Q912 DC-DC CONVERTER ICSWITCHING DRIVER Q904,Q905,Q906 DC-DC CONVERTER TRANSFORMER T901 RECT D911,917 RECT D909 D919 RECT D905 +45V (B+)

B+REG Q914

+16.7V (B+) +54V (B+)

16.7V (B)

HI-VOLTAGE DET IC903,Q920

Signal path : AUDIO

4-2. SCHEMATIC DIAGRAM MAIN SECTION (1/2) Refer to page 15 for Waveform and IC Block Diagram.

CNJ801

IC101(1/2) R101 C130 C109

IC102(1/2)

C111 R120

C231 R254 C221

R154 C102 R102 C107 R107

R104 R301 C110 C104

R303 R304 C301 C303 RV301 RV101 R302 IC301 R307 R305 R306 R308 C304 IC302(1/2) RV301

C106 CN803 C105

C108 R106
C207 R205 C208 C201 CNJ801

C902 R309 R310

R207 IC101(2/2) R202 C230 C209 IC202(1/2) C305 C211 R220
R201 C210 RV101 C204 R204 R208 R210 IC302(2/2) C212

R939 R938

(Page 13)
R941 C914 F902 F901 R834 C915 L901 L903 R942 D915 Q920 IC903 CN801
R853 R815 R809 C805 Q809 R901 Q901

D851 JR800

R851 R850

Q805 R810 R819

IC B/D

IC901 IC902

R909 Q902

D832 D827 D822

R908 R906 D901 C908 R905

PTH801

R812 D803

R821 R844 R902

D902 C907
Q903 C911 C912 R910 R912 C913
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note: Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice por tant le numro spcifi.
4-3. SCHEMATIC DIAGRAM MAIN SECTION (2/2)
R131 R155 IC102(2/2) Q103
C124 R147 Q105 R143 RV103 D108 Q108 R139 D106 R149 R160 R145 Q110 R150 D801 R802 Q114 CN804 R800 R801 Q112 C801
R133 Q102 C116 C123 R141 Q104 R123 RV102 C117 C118 Q101 R129 R134 C132 C126 R138 D104

R161 D802 Q109

D109 R144

C128 R151 Q111 Q113 R153

R124 R121 R122 R125 R126

R130 R156 R132

R146 R148

R235 R231 R255

C224 R247 Q212 Q205 R245 Q210 R250 R243
Q203 IC202(2/2) R233 Q202 C216 Q204 R242
RV203 D208 C227 D204 R241 D206 R239 R249

C228 R252

R223 R229 C217 RV102 C218 Q201 R230

R234 C232 C226 R238

D209 R244

Q209 R251 Q211

(Page 12)

R224 R221 R222 R225 R226

Q206 R256

R246 Q213 R248

D702 R701
R702 Q701 R808 Q804 R806 Q803 R807

C904 C905

C906 C903

R704 Q702

D703 R805 R804 Q802
Q914 T901 Q904 R918 Q911 R914 Q912 R924 R927 R915 Q913 R931 R932 Q908 R920 R917 R921 Q907 R933 R944 D910 R860 C860 Q909 C943 C916 D906 D918 L908 D920 C917 L907 R919 Q905 R930 R929 Q906 C942 C918 L902 C919 L906 C921 C922 C923 C927 R943 C920 D905 L905 D909 D919 C938 D917 D913 L904 C934 C940 D911 C932 R936 C936

R916 Q910

C928 C939 D912
JW100 JW104 R933 JW105 R928 JW101

JW102 Q909 JW103

C860 R919 R920 R921 R918 R917 R916 R915 Q907 R927 D906 R932 R930 R929 Q906 Q908 Q905 Q904 R931 R914 R924 D905

TP01 Q913 Q912

R860 JW137
JW138 JW141 JW148 JW151 JW150 JW140 JW152

R944 C943

JW139 JW142 JW149 JW153
CN801 TP04 TP07 JW109 JW145 JW144

JW123 JW124 JW110 JW143

JW154 JW356

JW159 C928 C927

JW127 TP13

JW129 TP08

JW130 TH801 JW115 JW116

JW135 JW131

JW353 Q911

JW121 C916 JW120 JW117

JW354 JW136 JW355

C922 C925

D909 D910
R911 JW293 R912 R821 D820 R903 C806 R844 C907 R905 R901 JW184 R818 JW189 R902 JW187 C913 R910 JW113 R820 C918

CN805 Q903

JW114 R913 C917

R252 JW290

C933 R937 D914 C935
JW179 TP21 C932 D913 R936
C938 JW178 C939 JW171 JW170

JW287 Q901

JW289 JW161
R909 C912 JW285 JW288 R907
C934 JW188 C908 JW164 C909 JW166 R904 JW165 C911 C941
4-4. PRINTED WIRING BOARDS MAIN SECTION Refer to page 15 for Semiconductor Location.

JW183 R941 C936

C305 R310

R942 TP28 C940 D915

R938 Q920

R309 C304 JW328

JW281 JW282

JW167 IC901

JW193 JW192

R853 R854 C111 R307

R111 R211
L904 R815 JW264 JW190 JW191

R939 D919

R308 C303

R110 R210

R857 R856 IC301 RV301

D854 C212

JW325 JW324 JW323 JW322 JW321 JR800 R222

C301 R303 R304 R301 R302 R305 R306 C302

R850 R851 C217 CN852

R122 JW350 JW320 C218 JW319 R224 JW318 C210 R208 R226 R225 Q201

JW265 JW266

JW326 JW327

R125 C118 R124 R126 D701

R245 JW270 JW271
R809 R703 D702 JW272 R702

R834 R812 C804

JW210 JW209

R828 JR216

JW313 JW162
IC202 JW312 C209 C201 JW311

C701 D703

R801 C801

R223 C216 R221 R220

R701 R108 R229

R243 D802 D801 R260

JW317 JW316 JW315 R123 JW314 C116 R121 R120

JR215 R238 D204

R261 R249

JW341 JW340

R232 R256 R255 R231

C231 C221

JW299 JW298

JW302 JW301 JW300

C105 C106

JW295 JW294

JW339 Q102 R130 JW329 JW330 JW331 JW338 JW337

JW343 JW342

JW212 JW211

R236 C225

R239 D208

R244 D207 D209

JW216 JW348

C202 C101 C222 C102

R154 C131

C224 R235

R204 C204 R206 R201 C230 R202 C203

R203 R207

JW309 JW308 JW307 R104 C104 R106 R101 C130 R102 C103

JW335 R135

JW347 JW346 Q205

JW305 JW304 JW303 R107

RV103 C125 R136

C206 C205 R205

R134 C107 C207 C208 JW296

R132 R155 R156 JW332

C108 C128

C901 C902

JW255 JW260 JW186 R150 JW185 JW258 JW334 JW259 JW256

JW251 JW252

JW248 JW249 R160 R161 JW234 JW235 JW238 Q114

JW245 JW246 R151

JW220 JW221 JW222 JW244 JW230 JW241 JW242 R143 JW239 JW243 R152 JW181 Q112 Q110 Q108 R139 R144 TH803 R146 Q111 R148 Q113 JW240 Q109 JW253 JW254 R149

C906 C903 JW225

JW236 JW237

JW231 JW232 JW233

JW227 JW228 JW229

R803 R153

C904 C905 R804 R805 Q804 C803 R806 R807

Q802 Q803

R140 D109

JR204 Q107 D104 R138

JW261 JW262 JW263 PTH801 D832 R833

TP24 FMB1

Semiconductor Location (MAIN BOARD)
Ref. No. D104 D106 D107 D108 D109 D204 D206 D207 D208 D209 D701 D702 D703 D801 D802 D803 D820 D822 D827 D832 D850 D851 D852 D853 D854 D901 D902 D905 D906 D909 D910 D911 D912 D913 D914 D915 D917 D918 D919 D920 IC101 IC102 IC202 IC301 IC302 IC901 IC902 IC903 Q101 Q102 Location F-11 E-12 E-12 E-12 E-12 B-9 C-9 B-9 C-9 B-9 F-8 E-8 F-8 D-9 D-8 E-8 E-5 E-12 B-8 B-12 J-7 J-8 J-7 J-6 J-7 G-6 G-6 B-2 C-2 D-5 D-5 D-5 E-5 D-6 E-6 D-6 D-5 E-5 D-7 D-6 G-9 G-8 H-8 G-7 H-6 F-6 F-8 D-6 G-8 F-9 Ref. No. Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q113 Q114 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 Q212 Q213 Q214 Q701 Q702 Q801 Q802 Q803 Q804 Q805 Q806 Q809 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Q915 Q920 Location F-10 F-10 E-10 E-10 F-11 F-11 E-11 F-11 D-11 G-11 D-11 D-11 H-8 F-9 D-9 D-9 D-10 D-9 B-9 B-8 B-9 B-8 B-10 B-7 B-10 C-9 E-8 F-8 D-8 B-11 B-11 B-11 D-8 D-8 E-8 F-6 F-6 G-5 D-2 D-2 E-2 G-2 F-2 F-2 E-4 E-4 E-2 E-2 E-6 E-6 C-6

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: Note: All capacitors are in F unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. % : indicates tolerance. 2 : nonflammable resistor. C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice por tant le numro spcifi.
A : B+ Line. B : B Line. H : adjustment for repair. Power voltage is dc 14.4V and fed with regulated dc power supply from +12V and REM terminals. Voltage and waveform are dc with respect to ground under no-signal condition. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO
for printed wiring boards: Note: X : parts extracted from the component side. : Pattern from the side which enables seeing.
IC Block Diagram IC901 TL5941NSR Waveform

REF. REG. 10 9

IC901 5

3.0Vp-p

0.1V OSC

15 sec 1V/div, 5 sec/div

XM-SD22X SECTION 5 EXPLODED VIEWS
NOTE: The mechanical parts with no reference number in the exploded views are not supplied. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE). (RED) R R Parts Color Cabinets Color Accessories are given in the last of this parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

IC101 IC102 IC202 IC301 IC302 IC901
8-759-710-97 8-759-710-97 8-759-710-97 8-759-909-71 8-759-909-71

IC IC IC IC IC

NJM4565M-D NJM4565M-D NJM4565M-D BA4558F BA4558F
6-703-643-01 IC TL594INSR < PHOTO TRANSISTOR >

IC902 IC903

6-600-354-01 PHOTO TRANSISTOR PC-17K1 6-600-354-01 PHOTO TRANSISTOR PC-17K1 < JUMPER RESISTOR >
JR100 JR103 JR106 JR107 JR204 JR205 JR206 JR207 JR208 JR215 JR216 JR217
1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
1-216-295-11 SHORT CHIP 1-216-295-11 SHORT CHIP < COIL >

L901 L902 L903 L904 L905

1-456-139-12 1-410-396-71 1-456-139-12 1-410-396-71 1-410-396-71
INDUCTOR FERRITE INDUCTOR FERRITE FERRITE
35uH 0.45uH 35uH 0.45uH 0.45uH
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.
Ref. No. L906 L907 L908 Part No. Description 0.45uH 0.45uH 0.45uH Remark Ref. No. Q914 Q915 Q920 Part No. Description Remark
1-410-396-71 FERRITE 1-410-396-71 FERRITE 1-410-396-71 FERRITE
6-550-693-01 TRANSISTOR KTC4373 6-550-690-01 TRANSISTOR KTA1661 6-550-693-01 TRANSISTOR KTC4373 < RESISTOR >
< THERMISTOR (POSITIVE) > PTH801 1-805-163-21 THERMISTOR, POSITIVE < TRANSISTOR > Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q113 Q114 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q211 Q212 Q213 Q214 Q701 Q702 Q801 Q802 Q803 Q804 Q805 Q806 Q809 Q901 Q902 Q903 Q904 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 8-729-034-51 6-550-686-01 6-550-031-01 6-550-032-01 6-550-691-01 6-550-692-01 8-729-041-66 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 8-729-034-51 8-729-034-51 6-550-686-01 6-550-031-01 6-550-032-01 6-550-691-01 6-550-692-01 8-729-041-66 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 X-3383-027-1 X-3383-028-1 8-729-034-51 6-550-690-01 8-729-034-51 8-729-034-50 8-729-034-51 8-729-034-50 8-729-034-51 8-729-034-50 8-729-034-51 6-550-693-01 8-729-052-82 8-729-034-50 8-729-034-51 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 6-550-693-01 6-550-693-01 8-729-034-51 8-729-034-51 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC3875 KTC2875-B-RTK HN4C06J-GRBL(TE85R) HN4A06J-GRBL(TE85R) KTA1045L-Y R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R120 R121 R122 R123 R124 R125 R126 R129 R130 R131 R132 R133 R134 R135 R136 R138 R139 R140 R141 R142 R143 R144 R145 R146 R147 R148 R149 R150 R151 R152 R153 R154 R155 R156 R160 R161 R201 R202 R203 R204 R205 R206 1-216-837-11 1-216-837-11 1-216-837-11 1-216-837-11 1-216-206-00 1-216-845-11 1-216-845-11 1-216-833-11 1-216-033-00 1-216-845-11 1-216-845-11 1-216-077-11 1-216-843-11 1-216-295-11 1-216-827-11 1-216-045-00 1-216-837-11 1-216-829-11 1-216-841-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-077-11 1-216-077-11 1-216-033-00 1-216-033-00 1-216-821-11 1-216-845-11 1-216-845-11 1-249-421-11 1-249-428-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-234-499-11 1-234-499-11 1-234-499-11 1-215-880-31 1-216-853-11 1-216-065-11 1-216-829-11 1-216-829-11 1-216-827-11 1-216-821-11 1-216-837-11 1-216-837-11 1-216-837-11

METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP SHORT CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP CARBON CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP
22K 22K 22K 22K 2.2K 100K 100K 10K 220 100K 100K 15K 68K 0 3.3K 680 22K 4.7K 47K 4.7K 4.7K 4.7K 15K 15K 1K 100K 100K 2.2K 8.2K 47 47
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/4W 1/4W 1/10W 1/10W 1/10W 1/10W
TRANSISTOR KTC2025L-Y TRANSISTOR 2SC4015TV2 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) TRANSISTOR KTC3875 TRANSISTOR KTC3875 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC2875-B-RTK HN4C06J-GRBL(TE85R) HN4A06J-GRBL(TE85R) KTA1045L-Y KTC2025L-Y
TRANSISTOR 2SC4015TV2 FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) FET PAIR ASSY (N) (IRF540) (set of 3) FET PAIR ASSY (P) (IRF9540) (set of 3) TRANSISTOR KTC3875 TRANSISTOR KTA1661 TRANSISTOR KTC3875 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET FET FET FET FET FKV550N FKV550N FKV550N FKV550N FKV550N KTA1504 KTC3875 KTA1504 KTC3875 KTA1504 KTC3875 KTC4373 KTA1281Y-AT KTA1504 KTC3875
RES-CHIP 47 5% 1/10W RES-CHIP 47 5% 1/10W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W METAL OXIDE METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10 470K 4.7K 4.7K 4.7K 3.3K 1K 22K 22K 22K 22K 2.2K 100K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W
FET FKV550N TRANSISTOR KTC4373 TRANSISTOR KTC4373 TRANSISTOR KTC3875 TRANSISTOR KTC3875
1-216-837-11 METAL CHIP 1-216-206-00 RES-CHIP 1-216-845-11 METAL CHIP
Ref. No. R207 R208 R209 R210 R211 R220 R221 R222 R223 R224 R225 R226 R229 R230 R231 R232 R233 R234 R235 R236 R238 R239 R240 R241 R242 R243 R244 R245 R246 R247 R248 R249 R250 R251 R252 R253 R254 R255 R256 R260 R261 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R701 R702 R703 R704 R800 R801 R802 Part No. 1-216-845-11 1-216-833-11 1-216-033-00 1-216-845-11 1-216-845-11 1-216-077-11 1-216-843-11 1-216-295-11 1-216-827-11 1-216-045-00 1-216-837-11 1-216-829-11 1-216-841-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-077-11 1-216-077-11 1-216-033-00 1-216-033-00 1-216-821-11 1-216-845-11 1-216-845-11 1-249-421-11 1-249-428-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-216-017-11 1-234-499-11 1-234-499-11 1-234-499-11 1-215-880-31 1-216-853-11 1-216-049-11 1-216-829-11 1-216-829-11 1-216-827-11 1-216-821-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-827-11 1-216-827-11 1-216-837-11 1-216-837-11 1-216-839-11 1-216-845-11 1-216-833-11 1-216-841-11 Description METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP SHORT CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP CARBON CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100K 10K 220 100K 100K 15K 68K 0 3.3K 680 22K 4.7K 47K 4.7K 4.7K 4.7K 15K 15K 1K 100K 100K 2.2K 8.2K 47 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/4W 1/4W 1/10W 1/10W 1/10W 1/10W 1/10W Ref. No. R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R815 R818 R819 R820 R821 R823 R828 R833 R834 R835 R844 R860 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919 R920 R921 R924 R927 R928 R929 R930 R931 R932 R933 R936 R937 R938 R939 R940 R941 R942 Part No. 1-216-857-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-857-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-295-11 1-216-845-11 1-216-815-11 1-216-817-11 1-216-827-11 1-216-828-11 1-216-828-11 1-216-829-11 1-216-841-11 1-216-295-11 1-216-833-11 1-216-206-00 1-216-825-11 1-216-827-11 1-216-837-11 1-216-836-11 1-216-849-11 1-216-065-11 1-216-190-00 1-216-190-00 1-216-061-11 1-216-073-00 1-216-073-00 1-216-073-00 1-216-186-00 1-216-049-11 1-216-049-11 1-216-009-11 1-216-009-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-049-11 1-216-001-00 1-216-001-00 1-216-001-00 1-216-001-00 1-216-001-00 1-216-001-00 1-216-825-11 1-216-825-11 1-216-033-00 1-216-821-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 1M 10K 10K 10K 10K 1M 10K 10K 10K 10K 0 100K 3.3K 3.9K 3.9K 4.7K 47K 0 10K 2.2K 2.2K 3.3K 22K 18K 220K 4.7K 3.3K 10K 10K 10K 330 1K 1K 1K 1K 1K 1K 1K 1K 2.2K 2.2K 220 1K 47K 68K 22K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W

5% 5% 5% 5% 5% 5% 5% 5%

1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
RES-CHIP 47 5% 1/10W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W ENCAPSULATED COMPONENT 0.22X2 5W METAL OXIDE 10 5% 2W F METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470K 1K 4.7K 4.7K 3.3K 1K 10K 10K 10K 10K 10K 10K 3.3K 3.3K 22K 22K 33K 100K 10K 47K 47K 47K 47K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP 1-216-841-11 METAL CHIP
1-216-089-11 RES-CHIP 1-216-843-11 METAL CHIP 1-216-837-11 METAL CHIP

Ref. No. R943 R944

Part No. Description 5% 5% Remark 1/10W 1/10W Ref. No. Part No. Description ACCESSORIES ************ 2-514-765-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH) 2-514-765-21 MANUAL, INSTRUCTION (GERMAN,ITALIAN) (AEP,UK,E) 2-514-765-31 MANUAL, INSTRUCTION (SPANISH, TRADITIONAL CHINESE) (AEP,UK,E) 2-514-765-41 MANUAL, INSTRUCTION (DUTCH,PORTUGUESE) (AEP,UK,E) 2-514-765-51 MANUAL, INSTRUCTION (SWEDISH,POLISH) (AEP,UK,E) 2-514-765-61 MANUAL, INSTRUCTION (GREEK,RUSSIAN) (AEP,UK,E) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 103 3-367-410-11 SCREW (DIA. 5X15), TAPPING (MOUNTING SCREW) 1-690-779-31 CORD (WITH CONNECTOR) (0.2m) 3-249-791-01 COVER (POWER) Remark
1-216-009-11 RES-CHIP 1-216-009-11 RES-CHIP
< VARIABLE RESISTOR > RV101 RV102 RV301 1-227-558-11 RES, VAR, CARBON 5KX2 (LEVEL) 1-227-558-11 RES, VAR, CARBON 5KX2 (LOW BOOST (40Hz)) 1-227-557-11 RES, VAR, CARBON 20KX2 (FILTER) < CERMET RESISTOR > RV103 RV203 1-241-764-11 RES, ADJ, CERMET 10K 1-241-764-11 RES, ADJ, CERMET 10K < SWITCH > S801 1-692-990-21 SWITCH, SLIDE (FILTER) < TRANSFORMER > T901 1-439-635-21 TRANSFORMER, DC-DC CONVERTER < THERMISTOR (NEGATIVE) > TH801 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) TH803 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) TH808 1-804-301-11 THERMISTOR, CHIP (NEGATIVE) ************************************************************* LED BOARD ********** < DIODE > D850 D851 D852 D853 D854 6-501-118-01 6-501-118-01 6-501-118-01 6-501-118-01 6-501-117-01 LED LED LED LED LED SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL6E10C-STP5 (POWER) SEL2110W-TP3 (PROTECTOR)

Bidder Information

Inspection of Property
Bidders are urged to view or inspect property prior to bidding. Failure to view or inspect shall not constitute cause for cancellation of sale. VSE Corporation may at its discretion provide photographs, slides or video presentation during the sale as a courtesy to its bidders. These presentations are reminders only. Bidders are warned against bidding on the basis of a photograph.

Export Only Property

Q. What is export only property? of It is property identified by U.S. Department to be sold as Export Only. A. Treasuryproperty cannot be entered intoThis means that this the
commerce of the United States. Without exception, Export Only goods must exit the country and cannot be registered, used, or sold again in the United States.
Q. Why Inspect? Is it possible Q. sample? to get a representative Corporation provides a A. VSEproperty offered for sale. brief description of to the This description is A. Representative samples of Export Only property inform bidders of items available for sale and to give are available after payment in full. Buyer bidders enough information to determine if he/she is
interested in inspecting the property. Bidders are cautioned that all weights, measurements and descriptions listed online or in a catalog must be considered an approximation and do not create a warranty that the property actually conforms to such description.
acknowledges that samples are required for resale in foreign markets only. Buyer must ensure that samples are promptly exported and not returned to the United States or entered into United States Commerce System.
the Q. What is of thecondition of the property? Condition items being offered for sale varies from New to Salvage. U.S. Department of the A. Treasury and VSE Corporation make no warranties
or guarantees, written, expressed or implied as to quality, quantity, condition, usability, weight, measure, year, model, mechanical condition, performance, or other specifications. Bidders must view or inspect all property they are interested in to obtain firsthand knowledge about these items. Bidders are responsible to obtain these details during the inspection times listed in published advertising or online.
go about exporting Q. How do I property is offered on theproperty? Export only condition that all licensing and federal permits will be met by A. the buyer before exportation. VSE Corporation
does not warrant the availability of such licensor permits, nor provide a list of all the requirements that must be met. It is recommended that you engage the services of a broker or bonded carrier, who may be located in the Yellow Pages, if you are not familiar will all the export requirements. Buyers are responsible to obtain and comply with all export requirements. For detailed export information visit:

BIDDING: Open and progressive, voice auction; it is the bidders responsibility to pay attention to items being offered for sale and to bid on items in which he is interested. Normally, items are sold in the sequence listed in the sales catalog. Lot numbers are for administrative purpose only and do not describe the property. CAUTION: lot numbers identify a particular item or portion of items being sold; however lot numbers posted on property during public inspection may not match catalog lot numbers. Bidders are responsible to ensure the catalog or announced description of any item they intend to purchase matches the property inspected. Sale of property will not be cancelled due to bidder misunderstanding, failure to pay attention to the bidding, or failure to inspect property. WRITTEN BID: Written bids may be submitted in person or by registered mail. Acceptable method of payment will be cashiers check. Make cashiers check payable to VSE Corporation/U.S. Treasury for the bid amount. Indicate sale number and lot number or description on outside of a sealed envelope. Mail all bids to 6681 River Run Road, Riverside, CA 92507-7128. Bids must be received no later than 4:00 p.m. PDT one day prior to sale date. Unsuccessful bids will be returned within five (5) business days via FedEx. As written bids are received prior to the auction start, they may be used as the opening bid for said lot during the live auction. If numerous written bids are received for one lot, the highest written bid will be used as the opening bid. DEPOSIT: Total purchases of $5000.00 or less will require payment in full on day of sale. A minimum deposit of $5000.00 is required on day of sale for purchases over $5000.00. Once purchases reach $5000.00, an immediate deposit of $5000.00 is required. PAYMENT FORM: Acceptable forms of payment are cash, cashiers check, or credit card (Visa, MasterCard, American Express or Discover Card). U.S. funds only. Bank wires may be used for final payment. Make cashiers check payable to VSE Corporation/U.S. Treasury. Personal or business checks, certified checks, travelers checks, bank letters, check cards or letters of credit are not accepted. ALL CREDIT CARD RECEIPTS MUST BE SIGNED BY ORIGINAL CARDHOLDER. Credit cards issued to a buyers spouse will not be accepted for use by the buyer. CHANGE: VSE Corporation does not make change for more than 10% of the purchase price. FINAL PAYMENT Final payments must be made by 4:00 p.m. PDT on Friday, August 22, 2008, at 6681 River Run Road, Riverside, CA 92507-7128. Bank wires may be used for final payment. NO EXTENSION FOR FINAL PAYMENT. Bank Wire Instructions: Citizens Bank 1 Citizens Drive Riverside, RI 02915 With Final Credit to: VSE Corporation Account #6218223853 Ref: Lot Number

Lot 39 CSPR EARRINGS: 18KW, HINGED HOOPS, 5.7 GRAMS, 28 DIAMONDS, ATW 0.56CT, COLOR AND CLARITY G/VS-SI Storage Vendor: VSE Warehouse-Riverside, CA EXPORT ONLY
Lot 40 CSEA RINGS: 18KW, GENTS, BAND, 13.0 GRAMS, 3 DIAMONDS, ATW 0.24CT, COLOR AND CLARITY G/VS-SI (1 EA), LADIES, 18KW, 7.5 GRAMS, 28 DIAMONDS, ATW 0.56CT, COLOR AND CLARITY G/VS-SI (1 EA), 18KW, LADIES, 4.9 GRAMS, 26 BAGUETTE CUT DIAMONDS, 24 FULL CUT ROUND DIAMONDS, ATW 0.50CT, COLOR AND CLARITY G/VS-SI, 1 OVAL RUBY, ATW 0.45CT (1 EA) Storage Vendor: VSE Warehouse-Riverside, CA EXPORT ONLY
Lot 41 CSEA CHAINS W/PENDANTS: 18KW DROP PENDANT W/CHAIN, 9.2 GRAMS, 22 BAGUETTE CUT DIAMONDS, 43 FULL CUT ROUND DIAMONDS, ATW 0.65 CT, COLOR AND CLARITY G/VS (1 EA), 18KW, DROP PENDANT W/CHAIN, 8.5 GRAMS, 19 BAGUETTE, 28 FULL CUT ROUND DIAMONDS, ATW 1.00CT, COLOR AND CLARITY G/VS (1 EA) Storage Vendor: VSE Warehouse-Riverside, CA EXPORT ONLY
Lot 42 ICEA TV MONITOR: SONY, MODEL: TRINITRON PVM-8042Q, S/N: 2010508 Storage Vendor: VSE Warehouse-Riverside, CA
Lot 43 CSBG LOOSE DIAMONDS: SINGLE CUT, 1MM ROUND, ATW 1.28CT, COLOR AND CLARITY G/VS-SI Storage Vendor: VSE Warehouse-Riverside, CA
Lot 44 IC2008260900000401014-QEA HANDBAGS: VARIOUS DESIGNS AND COLORS, LOUIS VUITTON Storage Vendor: VSE Warehouse-Riverside, CA
Lot 45 IC2008260900004901025-QEA WATCHES: GENT'S, STEEL, MARC ECKO, MODEL: E95004G1 (1 EA), GENT'S, STEEL, BULOVA, MODEL: C9671206 (1 EA), LADIES, 18K, ROLEX, OYSTER PERPETUAL DATEJUST, MODEL: 69178, S/N: 8999438, CIRCA 1985, AFTERMARKET DIAMOND BEZEL, ATW 0.64CT, COLOR AND CLARITY G/SI, PIN MISSING FROM BRACELET (1 EA) Storage Vendor: VSE Warehouse-Riverside, CA
Lot 46 CS2006530900008601004-QEA COMPUTERS: DELL, NOTEBOOK P3, 1.2GHZ, 20GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot 47 CS2008319500029401002-QEA LOOSE GEMSTONES: WATERMELON TOURMALINE SLICES, RANGING FROM 4MM TO 15MM DIAMETER (51 PRS), RANGING FROM 25MM TO 28MM DIAMETERS (2 PRS), WATERMELON TOURMALINE SLICES, SINGLE SLICES, 25MM DIAMETER (5 EA), SINGLE SLICES, 35MM DIAMETER (3 EA), QUARTZES: 14MM TRIANGLE BRIOLETTE CUT VARIETIES, AMETHYSTS: ATW 139.20CT (21 PCS), GREEN QUARTZ: ATW 138.30CT (20 PCS), COLORLESS QUARTZ: ATW 133.80CT (20 PCS), CITRINES: ATW 156.75 CT (23 PCS) Storage Vendor: VSE Warehouse-Riverside, CA
Lot 48 CS2008319500029401002-QEA STRANDS OF GEMSTONES: SMOKY QUARTZ: 18MM X 8MM, CUSHION SHAPE, ATW 171.85CT (2 STRANDS), AMETHYSTS: TWISTED DROP, ATW 165.25CT (1 STRAND), CITRINES: TWISTED DROP, ATW 311.45CT (2 STRANDS), QUARTZES: SMOKY, BI-COLOR, TWISTED DROP, ATW 422.45CT (2 STRANDS), AMETHYST: BARREL SHAPE PALE BEADS, ATW 405.5CT (2 STRANDS) Storage Vendor: VSE Warehouse-Riverside, CA

Lot 49 ICEA BRACELET: 10KY, LADIES, 8" LONG, 30.6 GRAMS, 231 DIAMONDS, ATW 2.00CT, COLOR AND CLARITY H/I-2 Storage Vendor: VSE Warehouse-Riverside, CA
Lot EA IC2007233000002901002 COIN ALBUM: VARIOUS U.S. AND FOREIGN, ATW SILVER 14.3 TROY OZ Storage Vendor: VSE Warehouse-Riverside, CA *******Lot 51 is offered for sale by order of the Internal Revenue Service- Criminal Investigations. The comprehensive crime control act of 1984 and U.S. Department of the Treasury policy prohibit the sale of forfeited property to a criminal defendant or person(s) acting as his/her agent. Property will be released to successful bidders within three (3) business days of auction after review of IRS records******* Lot 51 IREA WATCH: 18KW, GENTS, ROLEX PRESIDENT, MODEL: 118239, BLUE DIAL W/DIAMONDS AT HOUR STATIONS, AFTERMARKET DIAMOND BEZEL, S/N: K225381, CIRCA 2001 Storage Vendor: VSE Warehouse-Riverside, CA
Lot EA SSEA WASHING MACHINE: KENMORE ELITE, MODEL: HE 3T, S/N: EA SS2007310460000101067 DRYER: KENMORE, MODEL: HE4, S/N: 8577072 Storage Vendor: VSE Warehouse-Riverside, CA
Lot 53 CS2007270400077901001-QPCS RIFLE SCOPES: MILLETT PRECISION SPORTS OPTICS, 17 CTNS Storage Vendor: VSE Warehouse-Riverside, CA
Lot 54 CSEA SKIPJACK VESSEL: 20 FT., WHITE, S/N: BKP01842M79B Storage Vendor: Marine Group LLC- Chula Vista, CA NOT AVAILABLE FOR PREVIEW AT AUCTION LOCATION. SEE VENDOR PAGE FOR DETAILS. THIS BOAT DOES NOT AND WILL NOT COME WITH A TRAILER.
Lot 55 CSEA ELECTRONICS AND ASSORTED PROPERTY: CAR STEREO EQUIPMENT: SUBWOOFERS: KICKER, 12 (4 EA), KICKER, 15 (2 EA), ROCKFORD FOSGATE, MODEL: P1S415, 15, P1 SERIES (5 EA), MODEL: P1S412, 12, P1 SERIES (2 EA), SONY, X-PLOD, MODEL: XS-L124P5B, 12 (8 EA), PANASONIC, MODEL: CJ-SW3003U, 12 (2 EA), MODEL: CJ-SW2503U, 10 (2 EA), PYLE, BLUE WAVE, MODEL: PLWB12D, 12 (2 EA), SPEAKER BOXES: FOR 10 SUBWOOFER (4 EA), FOR 15 SUBWOOFER (1 EA), AMPLIFIERS: KOLE AUDIO, MODEL: XP2-1500, NITRIC SERIES, 2 CHANNEL, 1500 WATTS (1 EA), MODEL: XP2-2000, NITRIC SERIES, 2 CHANNEL, 2000 WATTS (1 EA), POWER ACOUSTIC, MODEL: SL2-1500, 2 CHANNEL (2 EA), MODEL: SL2-2400, 2 CHANNEL (1 EA), SONY, STEREO POWER, MODEL: XM165ZZ, REFURBISHED (1 EA), MODEL: XM2002GTW, REFURBISHED (1 EA), VIDEO MONITORS: DUPONT, MODEL: DP777X, FLIP DISPLAY (2 EA), TELEVISIONS: DUPONT, MODEL: DZ9001, 9, ROOF MOUNT (4 EA), PHOENIX DIGITAL (4 EA), PYLE VIEW, MODEL: PLDF7IN, 7, LCD (2 EA), HANNSPREE, MODEL: K206-100-002, S/N: 538AK206002C0031 (1 EA), MODEL: K206-1001-005, S/N: 521AK2060005A0118 (1 EA), DISNEY PRINCESS, MODEL: DT12-1001-000B, S/N: 540ADT12000C0027 (1 EA), PHONICS DIGITAL, MODEL: PD-VT, IN DASH MONITOR (2 EA), RECEIVERS: JVC CD PLAYER, MODEL: KD-S33, REFURBISHED (2 EA), JVC, MODEL: KD-AVX1, REFURBISHED (2 EA), POWER ACOUSTIC, MODEL: PAUS-850, CD PLAYERS (2 EA), POWER ACOUTSTIC, MODEL: PTID-5300, IPOD READY (2 EA), SUPER SONIC, CD PLAYER, MODEL: SUPER X SC-1899UM, (1 EA), METRIK, MULTIMEDIA, MODEL: MID-136 (2 EA), SONY, AM/FM/CD, MODEL: CDXGT300 (1 EA), PYLE VIEW, IN-DASH CD, MP3, DVD,MODEL: PLDTF5M, 2.5 TFT LCD DISPLAY (6 EA), PYLE VIEW, UNIVERSAL MOUNT MOBILE, CD/DVD/MP4/CD-R/CD-RW, MODEL: PLTD24 (5 EA), PYLE VIEW, CD, S/N: 07APLTFD12200371 (1 EA), PYLE VIEW, IN-DASH DVD/CD/MP3, 7 TOUCH-SCREEN DISPLAY, MODEL: PLTSN74 (4 EA), LEGACY, IN-DASH DVD/CD/MP3, 7 TOUCH-SCREEN DISPLAY, MODEL: LDTSN7 (1 EA), LEGACY, 3 LCD TFT DISPLAY, MODEL: LD34MUT (2 EA), KENWOOD, CD RECEIVER, MODEL: KDC-MP435U, W/USB INTERFACE (2 EA), HARMONTEC, DVD W/PROGRESSIVE SCAN, MODEL: DV-105 (4 EA), LVP DIGITAL, MODEL: LP7DVDT, W/7 LCD DISPLAY (7 EA), STIFFENING CAPACITORS: XPRESS, MODEL: CA156XS (1 EA), MODEL: CA156XB (1 EA), STEREOS: RCA, 5 DISC CD CHANGER, W/4 SPEAKERS, CD RECORD, MODEL: RS2664 (1 SET), DURABAND, 3 PIECE, CD/AM/FM/CASSETTE, MODEL: CD1493 (2 EA), WEATHER ALERT RADIOS: VECTOR, AM/FM NDAA WEATHER ALERT, 5 BLACK & WHITE TV DISPLAY, BATTERY AND HAND CRANK POWERED, 3 LED LIGHTS, MODEL: VEC130B (3 EA), DVD/VCR PLAYER: MAGNAVOX, MODEL: MWC20T6A (1 EA), PORTABLE DVD PLAYER: GPX, MODEL: PDL805, 8.5 DISPLAY (1 EA), JACKETS: HEAVY (3 EA) Storage Vendor: VSE Warehouse-Riverside, CA

Lot 56 CS2008550100013101003-QEA DISPLAY CABINETS: WOODEN Storage Vendor: VSE Warehouse-Riverside, CA
Lot 57 CS2006530900008601001-QEA COMPUTERS: DELL, MODEL: LATITUDE C640 P4, 2GHZ, 40GB, 256MB Storage Vendor: VSE Warehouse-Riverside, CA
Lot 58 CSEA COMPUTER PARTS: 3 1/2" FLOPPY DISK DRIVES Storage Vendor: VSE Warehouse-Riverside, CA
Lot 59 CS2006530900008601003-QEA COMPUTERS: DELL, NOTEBOOK PM, 1.4GHZ, 40GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot 60 CS2006530900008601002-QEA COMPUTERS: DELL, NOTEBOOK PM, 1.6GHZ, 40GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot 61 CS2008319500029401002-QBG ROUND SAPPHIRES: LOOSE, 1.8MM, ATW 1.52CT (1 BAG) Storage Vendor: VSE Warehouse-Riverside, CA
Lot 62 IC2008260900004901025-QEA RINGS: GENTS, 10KY/W, 13.7 GRAMS, 26 DIAMONDS, ATW 0.74CT, COLOR AND CLARITY H/I-2 (1 EA), LADIES 18KY, 9.0 GRAMS, 26 DIAMONDS, ATW 0.12CT, COLOR AND CLARITY H/I-1 (1 EA), LADIES 14KW RING, 6.0 GRAMS, 93 DIAMONDS, ATW 0.50CT, COLOR AND CLARITY H/I-2 (1 EA) Storage Vendor: VSE Warehouse-Riverside, CA
Lot 63 CS2006530900008601004-QEA COMPUTERS: DELL, NOTEBOOK P3, 1.2GHZ, 20GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot EA CSEA MICROSCOPES: MEADE CSEA TELESCOPES: TELESTAR CSEA TELESCOPE: NORTHSTAR Storage Vendor: VSE Warehouse-Riverside, CA
Lot 65 CS2006530900008601001-QEA COMPUTERS: DELL, MODEL: LATITUDE C640 P4, 2GHZ, 40GB, 256MB Storage Vendor: VSE Warehouse-Riverside, CA Lot 66 CS2006530900008601004-QEA COMPUTERS: DELL, NOTEBOOK P3, 1.2GHZ, 20GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot 67 CS2006530900008601003-QEA COMPUTERS: DELL, NOTEBOOK PM, 1.4GHZ, 40GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot 68 CSEA PAINT SPRAYERS: W/PAINT Storage Vendor: VSE Warehouse-Riverside, CA
Lot 69 CSEA MISCELLANEOUS ITEMS: OPERATIONS BATTERIES: LATHEM, 500E, P/N: VIS6001 (22 EA), SURGE PROTECTORS: CURTIS POWER 7, M/N: SP700-7TN (4 EA), SURGE MASTERS: BELKIN, M/N: F5C572-TEL, P/N: R52043-A (2 EA), BATTERY CHARGER: GP, M/N: KB-88A-7 (1 EA), HUB: OFFICE CONNECT, S/N: 0100/LT4G170065638 (1 EA), COMPUTER TOOL KIT: FELLOWS DELUXE, M/N: 49098 (1 EA), ZIP DRIVES: IOMEGA, 250MB, M/N: 11097, 8 PCS IN ONE PACK (304 EA), MEMORY MASTER UPGRADE KITS: PNY TECH, 128MB NOTEBOOK, M/N: N128S100Y (48 EA), MEMORY CARDS: RK-BYTE, 128MB SDRAM PC 100, M/N: 429420 KBYTE# 3, P/N: 761133664018 (33 EA), TONER CARTRIDGES: HP, LASERJET, MODEL: 92295A (5 EA), PRINT CARTRIDGES: HP, MODEL: 06A (5 EA), PRINT CARTRIDGES: HP, MODEL: 92A (4 EA), PRINTERS: HP, LASERJET, 1200N (2 EA), DIGITAL DVD BURNER: PACIFIC, PLUS, P/N: U-30134, S/N: 08DS00388 (1 EA), CARD SCAN: EXECUTIVE, S/N: 792980600607 (1 EA), USB2 HI-SPEED CABLES: BELKIN, M/N: F3U133-06 (2 EA), HARD DRIVE: WESTERN DIGITAL, WD800, S/N: WMA8E2776595 (1 EA), CAT 5E SNAGLESS PATCH: BELKIN, CABLE PRO SERIES, M/N: P95226-B, 7.6 M (1 EA), CAT 5E CROSSOVER: BELKIN, RJFT, P/N: P94493 (1 EA), 16 PORT DUAL SPEED HUB: NETGEAR, M/N: DS116NA, S/N: DS16F26117526 (1 EA), PRINT CARTRIDGES: HP, INKJET MODEL: 49 TRICOLOR (12 EA), PRINT CARTRIDGES: HP, INKJET, MODEL: 45 BLACK (66 EA), CLIPPER AND TRIMMER ALL IN ONE: WAHL, M/N: 79900 (1 EA), ELECTRONIC POCKET BIBLES: FRANKLIN, M/N: KJV-450, ISBN: 1-59074-098X (10 EA), TIME CARD RACK: ACROPRINT (1 EA), TIME CARD STAMP: ACROPRINT, M/N: 175, S/N: 556265 (1 EA), BLANK TIME CARDS: 1 BOX (218 EA), TIME CLOCK & DOCUMENT STAMP: LATHEM TIME (1 EA), DUST GUARDIAN: KINGSTON (1 EA), COMPUTER MAGAZINES (12 EA) Storage Vendor: VSE Warehouse-Riverside, CA

Lot 77 SSEA 2006 BENTLEY FLYING SPUR: BLACK, LEATHER INTERIOR, 6 LITER, 12 CYLINDER, 22" PIRELLI TIRES, ADDITIONAL EQUIPMENT: NAVIGATION SYSTEM, HEATED/COOLED SEATS, TELESCOPIC STEERING WHEEL, TINTED WINDOWS ON-BOARD COMPUTER, ODOMETER READS: 20,063, VIN: SCBBR53WX6C036543 Storage Vendor: VSE Warehouse-Riverside, CA
Lot EA SSEA DVD PLAYER: POLAROID, PORTABLE, W/CASE 1 EA SS2008310560000101016 DATA CARD PRINTER: MODEL: SP 35, S/N: D65796 Storage Vendor: VSE Warehouse-Riverside, CA
Lot 79 CS2007230400006101001-ACTNS SOCKS: ASSORTED STYLES, COLORS, AND SIZES, APPROXIMATELY 31 PALLETS TOTAL Storage Vendor: ARC LOGISTICS, INC - LAREDO, TX NOT AVAILABLE FOR PREVIEW AT AUCTION LOCATION. SEE VENDOR PAGE FOR DETAILS.
Lot EA 5 EA CS2006530900008601002-Q002 COMPUTERS: DELL, NOTEBOOK PM, 1.6GHZ, 40GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
5 EA 1 EA IC2006250100019201001 EVINRUDE BOAT: 16 FT., W/OUTBOARD MOTOR ICEA SURVEILLANCE CAMERA AND ACCESSORIES: RADIOSHACK, MODEL: 490-2515, S/N: 40293-16341 (1 EA), W/CAMERA ACCESSORIES AND 100FT CABLE EXTENSIONS (1 EA) ICEA VIDEO SURVEILLANCE SWITCHBOX: RADIOSHACK, 2-CHANNEL, MODEL: 49-2517, S/N: 40293-16379 ICEA 1970 SEARAY 200 VESSEL: HULL ID: CF5737 HY Storage Vendor: VSE Warehouse-Riverside, CA THESE BOATS DO NOT AND WILL NOT COME WITH TRAILERS. Lot EA IC2008260900000401014-Q002 HANDBAG: CHANEL Storage Vendor: VSE Warehouse-Riverside, CA Lot 83 IC2007550100001201001

Lot 81

LAPTOP: HEWLETT PACKARD, COMPAQ Storage Vendor: VSE Warehouse-Riverside, CA Lot 84 IC2008260900000401014-QEA HANDBAG: BURBERRY Storage Vendor: VSE Warehouse-Riverside, CA
Lot 85 ICEA LAPTOP: DELL, LATITUDE Storage Vendor: VSE Warehouse-Riverside, CA
Lot 86 CS2006530900008601004-QEA COMPUTERS: DELL, NOTEBOOK P3, 1.2GHZ, 20GB, 256MB, CDRW Storage Vendor: VSE Warehouse-Riverside, CA
Lot EA CSEA SPOTTING SCOPE: BUSHNELL, MODEL: SPACEMASTER 1 EA CS2008550100010301002 SPOTTING SCOPE: BUSHNELL, MODEL: SPACEMASTER, 20 - 45X60 MM 1 EA CS2008550100010301003 SPOTTING SCOPE: BUSHNELL, MODEL: SPACEMASTER, 20 - 60X60 MM 1 EA CS2008550100010301004 SPOTTING SCOPE: BUSHNELL, MODEL: SENTRY, 12 - 36X50 MM 1 EA CS2008550100010301006 SCOPE: BUSHNELL, MODEL: IMAGEVIEW CSEA SCOPE: BUSHNELL, MODEL: TROPHY CSEA SPOTTING SCOPES: BUSHNELL, MODEL: SENTRY Storage Vendor: VSE Warehouse-Riverside, CA 31 EA Lot EA CS2008550100010301005 RANGEFINDER: BUSHNELL, MODEL: SENTRY 2 EA CS2008550100010301009 RANGEFINDERS: BUSHNELL, MODEL: YARD PRO CSEA RANGEFINDERS: BUSHNELL, MODEL: YARD PRO SPORT 11 EA CS2008550100010301011 COMPASSES: BRUNTON, MIRRORED CSEA COMPASSES: BRUNTON, LENSATIC Storage Vendor: VSE Warehouse-Riverside, CA 2 EA Lot 89 IC2008260900000401014-QEA HANDBAG: DIOR IC2008260900004901025-QEA WATCH: GENT'S, 18K, ROLEX, OYSTER PERPETUAL DAY DATE, MODEL: 18238, S/N: E828683, AFTERMARKET DIAMOND BEZEL, ATW 1.00CT, COLOR AND CLARITY H/I-1, COUNTERFEIT DIAL Storage Vendor: VSE Warehouse-Riverside, CA Lot EA CSEA RADAR GUN: BUSHNELL 4 EA CS2008550100010301017 SOLAR PANELS: BRUNTON 3 EA CS2008550100010301018 SPOTLIGHTS: OPTRONICS, MODEL: NIGHTBLASTER Storage Vendor: VSE Warehouse-Riverside, CA Lot PCS CS2007270400077901001-Q003 RIFLE SCOPES: MILLETT REDDOT, BLACK, 6 CTNS Storage Vendor: VSE Warehouse-Riverside, CA Lot 92 CS2007270400077901001-QPCS CROSS BOW SCOPES: TEN POINT CROSSBOW TECH, 19 CTNS Storage Vendor: VSE Warehouse-Riverside, CA

3. REGISTRATION OF BIDDERS: All persons wishing to participate in the bidding process of the sale are required to obtain, completely fill out, and turn in a bidder registration card at the sale site prior to sale. An individuals signature/initials on the bidder registration card is an acknowledgment of his/her full and complete understanding of all terms and conditions of the sales contract and his/her agreement to be bound thereby. The sales catalog and sales brochure may also contain terms and conditions constituting part of the sales contract. Each bidder must present a Government-issued photo ID as a prerequisite of registration (i.e. drivers license, military ID or passport). Each bidder will be issued a bidder number along with a sales catalog upon completion of registration. Each registered bidder is solely responsible for the use of his/her bidder number and any use by another person is presumed to be with the consent of and contractually binding on the registered bidder.
2. ELIGIBILITY OF BIDDERS: The Bidder warrants that he/she is not: (a) under 18 years of age; (b) an employee of any department or agency of the Federal Government prohibited by the regulations of that agency from purchasing property sold hereunder; (c) an agent or immediate member of the household of the employee in (b), above; (d) the contractor, subcontractor or vendor, their agent or employee who has access to information concerning the property to be sold at U.S. Department of the Treasury auctions that is not generally available to the public; (e) presently debarred or declared ineligible for the award of contracts by any Federal agency in accordance with 41 CFR 101-45.6;
The registrant agrees that, should the registrant be the successful bidder on a lot, the following information regarding the transaction shall be published on the U.S. Department of Treasury auction website: 1). The registered bidders name; 2). The lot number; 3). The lot description; and, 4). Purchase price of lot. Electronic Freedom of Information Act Amendments of 1996 (5 U.S.C. 552 (2000)).

property, but do not alter in any way the basic terms and conditions of sale. An errata sheet will be distributed to provide bidders with an up-todate posting of lot additions, deletions, or modifications. The errata sheet information replaces the applicable corresponding information in the sales catalog. Further, no interpretation of any provision of the sale contract, including applicable performance requirements, shall be binding on the Government unless furnished or agreed to, in writing, by the Contracting Officer.
4. VIDEO RECORDING: The Contractor may videotape the conduct of sale which may be utilized in dispute resolution processing and for other purposes as needed. 7. ADDITION/WITHDRAWAL OF PROPERTY: The Government reserves the right to withdraw from sale any of the items listed in the sales catalog/brochure or to sell at auction items not listed.
5. INSPECTION OF PROPERTY: The bidder is invited, urged, and cautioned to inspect the property prior to submitting a bid. The failure to inspect property shall not constitute cause for cancellation of sale. The property or a representative sample of property will be available for inspection at the places and times specified by the contractor. Absolutely no access to property is allowed without prior contractor authorization.
8. PROPERTY DESCRIPTIONS: The Government warrants to the original Purchaser that the property listed in the sales catalog for bids will conform to its description. This warranty is in place of all other guaranties and warranties, express or implied. The Government does not warrant the condition, quality, or merchantability of the property or its fitness for any use or purpose. The condition of items offered varies from NEW to SALVAGE. The Purchaser understands and agrees that all property is purchased and accepted AS IS, WHERE IS and WITH ALL FAULTS. The amount of recovery under this provision is limited to the purchase price of the inaccurately described property. The Purchaser is not entitled

6. ORAL MODIFICATIONS:

STATEMENTS
Announcements may be made on the day of the sale to clarify property status, catalog descriptions, or other information specific to a lot or item. These announcements take precedence over sales catalog information pertinent to that
to any payment for loss of profit or any other money damages, including special, direct, indirect, incidental, or consequential. For Purchasers claiming recovery under the warranty of description, no refund will be made unless the Purchaser: a) submits a written notice to the Contractor within 30 calendar days of the date of removal that explains in what manner the property was inaccurately described. b) If the government agrees, then a full refund of the money received will be returned. If a misdescription is determined before removal of the property, the Government will keep the property and refund any money paid. If a misdescription is determined after removal, the Government will refund any money paid if the Purchaser takes the property at his/her expense to a location specified by the Contractor. The Purchaser must maintain the property in the same condition as when removed.

For open and progressive voice auction sales, it is the bidder's responsibility to pay attention to items being offered for sale and to bid on those items in which he/she is interested. (c) In the event of a dispute as to the amount bid, item or item number, and/or paddle number of the Bidder, the Government reserves the right to reoffer the item in question. Once the Government accepts a bid, a contract is established and the Purchaser may not withdraw the bid. The auctioneer will not accept unilateral conditions asserted by the high bidder. (d) The invoice, as to the name and number of the Purchaser, and the amount of the bid shall be prima facie evidence of these facts of the sale, and all disagreements will be resolved in accordance with such records;
10. COLLUSION: Practices that eliminate competition, such as collusive bidding, may warrant criminal, civil, or administrative action against the participant(s) and may be referred to the Department of Justice in accordance with 41 CFR 101-45.317.1.
9. OFFERING OF PROPERTY FOR AUCTION AND SUBMISSION OF BIDS AND AWARD: (a) The auctioneer will offer each item/lot in accordance with catalog sequence or by special announcement. All bidders will communicate their bid amounts orally or by such other means as may be recognized by and acceptable to the auctioneer. (b) A lot will be sold to the highest bidder upon acceptance of the final bid amount by the Government. In the event the bidding does not exceed the Government's minimum reserve price, the auctioneer will close the bidding subject to acceptance by the Government.
11. CONSIDERATION OF BIDS: The Government reserves the right to reject any or all bids, and to waive any technical defects in bids. All property is sold with a minimum reserve price unless the goods are, in explicit terms, offered without a minimum reserve price. If the minimum reserve price is not achieved, the Government may withdraw the goods at any time until the completion of sale.
13. DEPOSITS: 12. FORMS OF PAYMENT: Forms of payment are cash, cashier's check, or credit card (Visa, MasterCard, American Express, and Discover), where acceptable by the Government. Photo identification of the registered bidder must be presented to initiate the payment process. Payment for each lot must be made by the successful registered bidder for that specific lot. Cashier's Checks must be made payable to the VSE Corporation/U.S. Treasury. Personal or business checks, bank letters, or letters of credit are not acceptable. All cash payments of $10,000 or more will be reported to the IRS in accordance with 26 USC 6050 Section I (d). In order to comply with this requirement, bidder must provide their Social Security Number or Federal ID number if a business, along with date of birth at the time of payment in order for completion of IRS Form 8300. Acceptance of credit cards is subject to verification and approval by the issuing institution. Credit cards issued in the name of the registered bidder or the company he/she represents are the only cards that will be accepted for payments. Each credit card receipt must be signed by the original cardholder. Credit cards issued to a Purchasers spouse or in another individuals name will not be accepted for use by the Purchaser. The Purchaser agrees to the publication of his/her/company registered name, lot number, lot description and purchase price on the U.S. Department of Treasury auction website. Electronic Freedom of Information Act Amendments of 1996 (5 U.S.C. 552 (2000)). The Purchaser agrees to make deposits in accordance with the instructions in the sales catalog/brochure. The Purchaser agrees to pay for property awarded to him/her in accordance with their successful bid.

14. FINAL PAYMENT: Full payment of the purchase price must be received by the Contractor within the time specified in the sales catalog/brochure and prior to the release of any property. In addition to the forms of payment listed in paragraph 12, bank wires may be used for final payments. Any electronic bank transfer must originate from an account of the registered bidder or the business the bidder represents. The transfer must include the bidder number and all applicable auction sale lots. Any electronic bank transfers received from an account other than that of the registered Purchaser will not be accepted and will be returned to the originating bank. All final payments must be made and received by the date and time specified in the sales catalog/brochure or the bidder will be placed in default of the contract. The Purchaser agrees to the publication of his/her/company registered name, lot number, lot description and purchase price on the U.S. Department of Treasury auction website. Electronic Freedom of Information Act Amendments of 1996 (5 U.S.C. 552 (2000)).

15. APPLICABLE TAXES:

All purchasers are responsible for the payment of any and all applicable taxes imposed by any state, country, county, or political subdivision. The Purchasers may be required to pay such taxes to the cashiers at time of sale or to tax officials after purchase is made. If sales taxes are required, presentation of proof of payment will be required prior to property release.
initiation of any shipment preparations. If a Purchaser designates a representative agent, broker or transporter to pick up their sale property, the Purchaser must prepare and sign an authorization letter identifying the agent to act on their behalf. The Agent must present photo identification to validate the Purchasers option prior to initiation of any action.
16. ISSUANCE OF PAYMENT/RELEASE DOCUMENTATION : Upon receipt of full and final payment for each purchase, the Contractor shall provide the Purchaser with a receipt of each deposit or payment. Sale receipt(s) and release documents will only be issued in the name/company name of the registered bidder.
18. REMOVAL FROM SALES CENTERS OR COMMERCIAL STORAGE LOCATIONS: Any items purchased at auction will be released to the Purchaser or his designated representative upon presentation of the sale receipt(s) and release document(s). If Purchaser elects to have a designated representative (transporter, broker, other) pick up his/her property, that person must have all sale receipt(s) and release document(s) and an authorization letter signed by the Purchaser for removal. All property stored at the Contractors facilities must be removed by the dates specified in the sales catalog/brochure; no extensions of storage time will be granted. The failure to pick up property by the specified time will be declared a default against the Purchaser as specified in paragraph 23. All property stored at commercial warehouse facilities must also be picked up by the time specified in the sales catalog/brochure and an appointment should be scheduled in advance. The failure to pick up property by the specified time will be declared a default against the Purchaser as specified in paragraph 23.

17. PREPARATION FOR SHIPMENT, LOADING AND REMOVAL: (a) The Purchaser is responsible for making all arrangements for the packaging and removal of their purchases. When property is described in the sales catalog as being boxed, packed, crated, skidded, or in containers, the Government does not warrant that the property, as packaged, is suitable for shipment. Segregation, culling, or selection of property for the purpose of effecting partial or incremental release will not be permitted. No partial release will be permitted. The Purchaser shall remove the property at his/her expense. (b) All Purchasers or their authorized representatives will be required to present sale receipt(s) and release document(s) prior to the
19. REMOVAL OF EXPORT ONLY:
Any property listed in the sales catalog "For Export Only" may not be entered into the commerce of the United States and must be exported under conditions described in the sales catalog/brochure. A representative sample from large, commercial quantity Export Only lots (greater than ten cartons) may be released to the Purchaser upon full payment if the sample is available at the sales center. All Purchasers are responsible for complying with all applicable federal licensing and permit regulations prior to exportation. The failure of the purchaser to obtain necessary licensing will not result in the return of any monies tendered for the goods. The Contractor shall provide a copy of the required procedures for export, when available from the Government, to the Purchaser at the time of final payment. Unless a different period for removal is applicable with respect to goods or conveyances that are sold "For Export Only," the purchaser will have 60 days from auction day to remove the property from the United States or purchaser will be deemed in default and the property will be resold by the Government as provided in paragraph 23 of these Terms and Conditions of Sale. All forms required for exportation may be obtained at a nominal cost from the U.S. Government. Because of the complexity of some export requirements, the purchaser may wish to secure the services of a Customhouse Broker, bonded carrier, or other professional in securing the necessary documents required for exportation. The Contractor will offer no assistance whatsoever.
20. LIMITATION OF GOVERNMENT LIABILITY: Except for reasonable packing, loading, and transportation costs (such packing, loading, and transportation costs being recoverable only when a return of property at the Governments cost is specifically authorized in writing by the Contracting Officer or other costs authorized in writing by the Contracting Officer) the measure of the liability of the Government under any provisions of the terms and conditions in any case where liability of the Government to the Purchaser has been established shall not exceed the refund of such portion of the purchase price as the Government may have received.

21. TITLE: The Contractor shall furnish the Purchaser with all documents in its possession that have been provided to the Contractor by the government relating to the title, registration, or licensing of the property sold to the purchaser. However, the Government does not warrant or guarantee that the documents it possesses and furnishes to the purchaser, if any, are sufficient to obtain any necessary licenses, registrations or titles, or that licenses, registrations or titles can be obtained.
22. MARITIME EXPORTATION: The Purchaser, whether a U.S. citizen or an alien, may not export any vessel from the United States or its territories or possessions without first obtaining the approval of the DEPARTMENT OF TRANSPORTATION, MARITIME ADMINISTRATION, WASHINGTON, D.C. 20590,
pursuant to the provision of the Shipping Act of 1916, as amended (46 U.S.C. 801 et. seq.). To export a commercial vessel, a license from the DEPARTMENT OF COMMERCE, BUREAU OF INDUSTRY AND SECURITY, BUREAU OF EXPORT ADMINISTRATION, WASHINGTON, D.C. 20230, is required. For further information, contact (202) 482-2721.
party to this sale or has had any interest in the property at any time.
25. FALSE ADVERTISING AND UNFAIR OR DECEPTIVE ACTIONS: The use of false or misleading advertisements in commerce or other unfair or deceptive practices are unlawful (15 U.S.C. 45, et seq.). In disposing of any property purchased from the Government, purchasers should exercise extreme caution in preparing advertisements to ensure that they do not violate applicable Federal, state or foreign government laws.
23. DEFAULTS: The failure to make required deposit or final payments and/or comply with the time frames specified in the sales catalog/brochure for removal of property shall be deemed forfeiture of any rights, title, and interest the Purchaser may have acquired. The title of such property shall revert back to the Government without further notice to the Purchaser and will result in any monies paid being forfeited. The transaction shall be null and void as to the Purchaser. The property will be processed for resale at the next available auction.
26. DISPUTES: Any contract resulting from this offering is subject to the Contract Disputes Act of 1978, Public Law 95-563. The current "Dispute" clause found in 48 CFR 52.233-1 is hereby incorporated by reference. All requests for refunds or adjustments should be submitted to the contractor.
24. REQUIREMENTS TO COMPLY WITH APPLICABLE LAWS AND REGULATIONS: It is the Purchasers responsibility to ascertain and comply with all applicable Federal, State, local, and multi-jurisdictional laws, ordinances and regulations pertaining to the registration, licensing, handling, possession, transportation, transfer, export, processing, manufacture, sale, use, or disposal of the property listed in the sales catalog. The Purchaser or user of this property is not excused from any violation of such laws or regulations either because the United States is a Any disputes which cannot be resolved by the contractor may be directed to: Contracting Officer Department of the Treasury Departmental Offices Procurement Services Division 1500 Pennsylvania Avenue, NW Room 1425 New York Avenue Suite 2100 Washington, D.C. 20220

U. S. Department of the Treasury

AUCTION CALENDAR

August 2008

20 20th

November 2008
5 Miami, FL 11th Tucson, AZ
Riverside, CA Shakopee, MN

(1) (3)

SUN MON TUE WED THU
SUN MON TUE WED THU FRI SAT

September 2008

9th Tucson, AZ 17th Dayton, NJ (3) (1)

December 2008

3rd Riverside, CA (1)

October 2008

January 2009 January 2009

Dayton, NJ

KEY TO TYPES OF AUCTIONS 1- CYCLIC
Public auction held on a regular basis, every 2 to 3 months depending on location. A wide variety of merchandise is sold. Examples include vessels, aircraft, jewelry, wearing apparel, industrial goods, and other general merchandise.

2 - SPECIALTY

Public or online auction of a unique item or items, such as aircraft, jewelry, vessels or art.

3 - CONSIGNMENT

Public auction consigned to a local auctioneer in which vehicles and boats are the commodity.
SALES ARE CONTINUOUSLY ADDED. DATES ARE SUBJECT TO CHANGE.
Call the Auction Line at (888) 534-2828 or fax (703) 960-5789 for updated information.
www.treas.gov/auctions/treasury/gp Sales conducted by www.ricklevin.com www.manheim.com VSE Corporation in conjunction with Rick Levin & Associates and Manheim Auctions
REPORT U.S. GOVERNMENT FRAUD
If you, or someone you know suspects fraud against the federal government you may report this activity to one of the agencies listed below. You may be entitled to a reward.
U.S. Customs and Border Protection (CBP) - Border violations, fraud involving U.S. imports and exports, call: 1-800-ITS-FAKE Immigration and Customs Enforcement (ICE) Report suspicious activity relating to immigration enforcement by calling: 1-866-DHS-2-ICE Internal Revenue Service (IRS) Tax law violations and fraud, go online: www.irs.gov/compliance/enforcement Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) Report suspicious activity relating to arson, explosive materials, firearms and cigarettes, go online: www.atf.gov/contact U.S. Secret Service (SS) Report fraud/violations relating to counterfeit currency, financial fraud, identity theft/fraud, computer fraud, forgery, money laundering and credit card fraud, go online: www.secretservice.gov/contact.shtml Office of Foreign Assets Control (OFAC) Report suspicious activity relating to economic funding of terrorism and narcotics trafficking by calling: 1-800-540-6322