2003 SONY MOBILE PRODUCT GUIDE
1600W max power 500W x 1 RMS into 4W, 20Hz - 300Hz @ 0.2% THD 900W x 1 RMS into 2W, 20Hz - 300Hz @ 0.6% THD Class D Variable 50 - 300Hz 12dB/oct Low Pass Filter 40Hz EQ Boost RCA & Speaker Level Inputs
XM-D1000P5 Monaural Power Amplifier
Audio Power Specifications POWER OUTPUT AND TOTAL HARMONIC DISTORTION 500 watts minimum continuous average power into 4 ohms, 20 Hz to 300 Hz with no more than 0.2% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications Circuit system Inputs Outputs Suitable speaker impedance Maximum outputs Rated outputs (supply voltage at 14.4 V) 500 W (Hz, 0.2% THD, at 4W) 900 W (Hz, 0.6% THD, at 2W) Hz ( +0.5 dB, -3 dB) 0.06% or less (at 100 Hz, 4W) 0.3 6.0 V (RCA pin jacks) 1.2 12.0 V (High level input) Hz, 12 dB/oct dB (40 Hz) 12 V DC car battery (negative ground) 10.5 - 16 V at rated output : 90 A (2W) Remote input : 2 mA Approx. 339 mm (w/h/d) (13 3/1/3/8 in.) (w/h/d) not incl. projecting parts and controls Approx. 3.8 kg (8 lb. 6 oz.) not incl. accessories Mounting screws (5) High level input cord (1) Protection cap (1) Class D Technology Pulse power supply RCA pin jacks High level input connector Speaker terminals Through out pin jacks 2 8W 1,000 W (at 4W) 1,600 W (at 2W)
Frequency response Harmonic distortion Input level adjustment range Low-pass filter Low boost Power requirements Power supply voltage Current drain Dimensions
Mass Supplied accessories
Design and Specifications subject to change without notice.

Connections

Remote Output 12V Car Battery Ground

3 - 40A fuses

Subwoofer OUT
High Level Input Connection
Through Output Line Input

Dimensions

57 (/ 4 ) 327 (/ 8 ) 6 ( 1/ 4)

Unit: mm (in.)

339 (/ 8 )

311 (/ 4 )

119 (/ 4 )

202 (8)

347 (13 3/4 )

Emplacement et fonction des commandes

POWER/PROTECTOR

70 100

LOW BOOST (40Hz)

1 Indicateur POWER/PROTECTOR Sallume en vert en cours de fonctionnement. Lorsque PROTECTOR est activ, le voyant passe du vert au rouge. Lorsque PROTECTOR est activ, reportez-vous au guide de dpannage. 2 Commandes de rglage de la frquence de coupure Rgle la frquence de coupure (Hz) pour les filtres passe-bas. 3 Commande de niveau LOW BOOST Tournez cette commande pour amplifier les frquences autour de 40 Hz un maximum de 10 dB. 4 Commande de rglage LEVEL Le niveau dentre peut se rgler avec cette commande. Tournez cette commande dans le sens des aiguilles dune montre lorsque le niveau de sortie de lautoradio semble faible.

Troubleshooting Guide

The following checklist will assist in the correction of most problems which you may encounter with your unit. Before going through the checklist below, refer to the connection and operating procedures. Problem
The POWER/PROTECTOR indicator does not light up.

Cause/Solution

The fuse is blown. t Replace all fuses with a new one. The ground wire is not securely connected with a new one. t Fasten the ground wire securely to a metal point of the car. The voltage going into the remote terminal is too low. The connected car audio unit is not turned on. t Turn on the car audio unit. The system employs too many amplifiers. t Use a relay. Check the battery voltage (10.V).

Owners Record

The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. XM-D1000P5 Serial No.
The POWER/PROTECTOR indicator will change from green to red.
Turn off the power switch. The speaker outputs are short-circuited. t Rectify the cause of the short-circuit. Turn off the power switch. Make sure the speaker cord and ground wire are securely connected. The unit heats up abnormally. Use speakers with suitable impedance. t2 8. Make sure to place the unit in a well ventilated location. The power connecting cords are installed too close to the RCA pin cords. t Keep the power connecting cords away from the RCA pin cords. The ground wire is not securely connected. t Fasten the ground wire securely to a metal point of the car.

Specifications

AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 500 watts minimum continuous average power into 4 ohms, 20 Hz to 300 Hz with no more than 0.2% total harmonic distortion per Car Audio Ad Hoc Committee standards.

Other Specifications

Class D Technology Pulse power supply RCA pin jacks High level input connector Outputs Speaker terminals Through out pin jacks Suitable speaker impedance 28 Maximum outputs 1,000 W (at 4 ) 1,600 W (at 2 ) Rated outputs (supply voltage at 14.4 V) 500 W (Hz, 0.2 % THD, at 4 ) 900 W (Hz, 0.6 % THD, at 2 ) Frequency response Hz ( dB) Harmonic distortion 0.06 % or less (at 100 Hz, 4 ) Input level adjustment range 0.3 6.0 V (RCA pin jacks) 1.2 12.0 V (High level input) Inputs Circuit system Low-pass filter Hz, 12 dB/oct Low boost dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.V Current drain at rated output: 90 A (at 2 ) Remote input: 2 mA Dimensions Approx. 339 mm (13 3/1/3/8 in.) (w/h/d) not incl. projecting parts and controls Mass Approx. 3.8 kg (8 lb. 6 oz.) not incl. accessories Supplied accessories Mounting screws (5) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice.

Installation

Before Installation
Mount the unit either inside the trunk or under a seat. Choose the mounting location carefully so the unit will not interfere with the normal movements of the driver and it will not be exposed to direct sunlight or hot air from the heater. Do not install the unit under the floor carpet, where the heat dissipation from the unit will be considerably impaired. First, place the unit where you plan to install it, and mark the positions of the four screw holes on the surface of the mounting board (not supplied). Then drill the holes approximately 3 mm (1/8 in.) in diameter and mount the unit onto the board with the supplied mounting screws. The supplied mounting screws are 15 mm (19/32 in.) long. Therefore, make sure that the mounting board is thicker than 15 mm (19/32 in.).

Avant linstallation

Installez lappareil dans le coffre ou sous un sige. Choisissez un endroit de montage judicieux pour que lappareil ne gne pas les mouvements naturels du conducteur et pour quil ne soit pas expos aux rayons directs du soleil ou proximit dune bouche dair chaud. Ninstallez pas lappareil sous le tapis, car 327 (12 7/8) cela empcherait la dissipation de chaleur de 57 (2 1/4) lappareil. 1

Input Connections

Fuse Replacement
If the fuse blows, check the power connection and replace all fuses. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.

Connexions dentre

Pour plus de dtails sur les rglages des commutateurs et commandes, reportez-vous Emplacement et fonction des commandes.
For details on the settings of switches and controls, refer to Location and Function of Controls.

2 to 8.

Make the terminal connections as illustrated below. Effectuez les connexions des bornes comme illustr ci-dessous.
Do not connect any active speakers (with built-in amplifiers) to the speaker terminals of the unit. Doing so may damage the active speakers. Avoid installing the unit in areas subject to: high temperatures such as from direct sunlight or hot air from the heater rain or moisture dust or dirt If your car is parked in direct sunlight and there is a considerable rise in temperature inside the car, allow the unit to cool down before use. When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc. If this unit is placed too close to the car audio unit or antenna, interference may occur. In this case, relocate the amplifier away from the car audio unit or antenna. If no power is being supplied to the car audio unit, check the connections. This power amplifier employs a protection circuit* to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connecting improper loads. Do not use the unit on a weak battery as its optimum performance depends on a good power supply. For safety reasons, keep your car audio volume moderate so that you can still hear sounds outside your car.
Line Input Connection (with Speaker Connection

1 or 2)

Warning
When replacing the fuse, be sure to use one matching the amperage stated above the fuse holder. Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit.
Line Input Connection (with Speaker Connection 3) Connexion dentre de ligne (avec connexion de hautparleur 3)

Car audio unit Autoradio

Connexion dentre de ligne (avec connexion de hautparleur 1 ou 2)
Car audio unit Autoradio LINE OUT*
LINE OUT* Left channel Canal gauche Right channel Canal droit

Fuse (150 A) Fusible (150 A) +12 V car battery Batterie de voiture +12 V * If you have the factory original or some other car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. * Si vous disposez du modle dorigine ou dun autre autoradio dont lamplificateur ne comporte pas de sortie de tlcommande, raccordez la borne dentre de tlcommande (REMOTE) la prise dalimentation accessoires.
Si vous avez des questions ou des problmes concernant votre appareil qui ne sont pas abords dans ce mode demploi, adressez-vous votre distributeur Sony le plus proche.
Subwoofer* (min. TOTAL 4 ) Caisson de grave* (min. TOTAL 4 )
Subwoofer (min. TOTAL 2 ) Caisson de grave (min. TOTAL 2 )
* When you use two terminals with speakers, each of terminal resistance is 4 at a minimum. (Two terminals are connected with each other in the unit.)
* Lorsque vous utilisez deux bornes avec des hautparleurs, la rsistance de chaque borne doit au moins tre gale 4. (Les deux bornes sont raccordes lune lautre dans lappareil.)
Notes on the power supply Connect the +12 V power supply wire only after all the other wires have been connected. Be sure to connect the ground wire of the unit securely to a metal point of the car. A loose connection may cause a malfunction of the amplifier. Be sure to connect the remote control wire of the car audio unit to the remote terminal. When using a car audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. Use the power supply wire with a fuse attached (150 A). Place the fuse in the power supply wire as close as possible to the car battery. Make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 4-Gauge (AWG-4) or have a sectional area of more than 22.0 mm2.
Remarques sur lalimentation lectrique Raccordez le cble dalimentation +12 V uniquement aprs avoir ralis toutes les autres connexions. Raccordez correctement le cble de masse une partie mtallique de la voiture. Une connexion lche peut provoquer un dysfonctionnement de lamplificateur. Veillez raccorder le fil de tlcommande de lautoradio la borne de tlcommande. Si vous utilisez un lautoradio dont lamplificateur ne comporte pas de sortie de tlcommande, raccordez la borne dentre de la tlcommande (REMOTE) la prise dalimentation accessoires. Utilisez un cble dalimentation muni dun fusible (150 A). Fixez le cble dalimentation le plus prs possible de la batterie de voiture. Assurez-vous que les cbles raccorder aux bornes +12V et GND de cet appareil sont dun calibre dau moins 4 (AWG-4) ou dune section suprieure 22, 0 mm2.

1-Speaker System (with Input Connection B) Systme 1 haut-parleur (avec connexion dentre B)
2-Way System (with Input Connection C) Systme 2 voies (avec connexion dentre C)
Subwoofer (min. TOTAL 2 ) Caisson de grave (min. TOTAL 2 ) Left subwoofer (min. TOTAL 2 ) Caisson de grave gauche (min. TOTAL 2 ) Right subwoofer (min. TOTAL 2 ) Caisson de grave droit (min. TOTAL 2 ) Full range speakers Haut-parleurs large bande