3-257-674-21 (1)

Features

The XA-CC1 is a connection adapter for connecting a car cradle to a Sony master unit having the CD/ MD changer control function. Sony car audio units being compatible with PEGA-CC5 include: Units with CD/MD changer control from 2004 forward Following units MEX-5DI, CDX-M1000TF, CDX-MP80, CDX-M850MP, CDX-M800, CDX-MP40, CDX-CA680X, CDX-MP70, CDX-MP30, CDX-M730, CDX-M630, CDX-CA900, CDX-CA700X, CDX-CA700, CDX-CA600X, CDX-CA600, MDX-CA790X, MDX-M690, MDX-CA680X, MDX-CA580, XR-CA670X, XR-CA370X, XR-CA370, XR-CA630X, XR-CA430X, XR-CA440, XR-CA600V, XR-CA600

Specifications

Power requirement Dimensions Mass Input Output 12 V DC negative earth Approx. 97.2 55.7 23.7 mm (3 7/1/4 15/16 in.) (w/h/d) (not including connection cable) Approx. 260 g (10 oz) (including connection cable) Car cradle I/O input (8pin) SONY-BUS control output (8pins) SONY-BUS audio output (RCA-pin) ATT control output

Connection Adapter

Operating Instructions
Design and specifications are subject to change without notice.

Installation

Before installation
Choose the installation location carefully so that the unit does not interfere with normal driving operations. Avoid installing the unit where it would be subject to : high temperatures, such as from direct sunlight or hot air from the heater. draft, rain or moisture. dust or dirt. magnetic fields. Install the unit in a location that does not obstruct the operation of passenger-side airbag.

Installation location

You are recommended to install the unit inside the car panel or glove box. Please consult a qualified technician or service personnel if you cannot attach the connection adapter to the car securely. If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer. Contents of this manual are printed on using VOC (Volatile Organic Compound)-free vegetable-oilbased ink.

XA-CC1

2004 Sony Corporation Printed in Japan

Connections

Precautions
Before making any connection, disconnect the earth terminal of the car battery to avoid short circuits.

Connection diagram

Black/white striped
1.6m Car battery adapter (supplied with the Car cradle)
0.3m Cigarette socket power cord (supplied)*
continuous power supply earth

Connection example

Car cradle

BUS CONTROL OUT

Car cradle 1.6m 1m
Sony BUS compatible CD/MD changer (optional)
BUS CONTROL IN Connection Adapter XA-CC1 BUS AUDIO IN I/O

SONY BUS

BUS AUDIO OUT ATT or ATT OUT
Light blue Source selector XA-C30 (optional) 1m
Supplied with the CD/MD changer
* Tap the +12V after the fuse box, not directly from the battery. If the connected power supply cord is long, attach fuse (2.5A).
BUS CONTROL IN BUS CONTROL IN

Supplied with XA-C30

Connection Adapter XA-CC1
Source selector XA-C30 (optional)
BUS AUDIO IN BUS AUDIO OUT

Front speaker

BUS AUDIO IN BUS CONTROL OUT

Rear speaker

Sony BUS compatible car audio

3-256-434-21 (1)

Equipment used in illustrations (not supplied)

Front speaker

Rear speaker

CD/MD changer

Car Cradle

Installation/Connections

Connection example
Car cassette adapter connection
Car audio cassette player
Car connecting pack CPA-9C (optional)

LINE OUT

Sony BUS compatible car audio connection

PEGA-CC5

2004 Sony Corporation Printed in Japan
Connection adapter XA-CC1 (optional)

BUS AUDIO IN

BUS CONTROL IN

Parts Iist

2 holding arm (S) 3 holding arm (L)
Sony BUS compatible car audio

1 car cradle

Sony BUS compatible car audio and Sony BUS compatible CD/MD changer connection 4 holding arm (L2) 5 mounting attachment 6 support arm (S)

7 support arm (L)

8 rubber block

9 holding clip (S)

0 holding clip (L)

qz car battery adapter

qs GPS aerial

Connection adapter

XA-CC1

(optional)

1.6 m 3m
qd base sheet for GPS aerial

qf cord clamp

qg two-sided tape
Source selector XA-C30 (optional)

BUS CONTROL OUT

Customer Support
For the latest support information, check our official Sony CLI Web site Customers in Europe http://www.clie-link.com Contents of this manual are printed on using VOC (Volatile Organic Compound)-free vegetable-oil-based ink.

BUS AUDIO OUT

Sony BUS compatible CD/ MD changer

Connection diagram

car audio cassette player

cigarette lighter socket

LINE OUT I/O

DC 5.2V

GPS ANT
Connection Adapter XA-CC1 (optional) Light blue ATT Front speaker ATT Source selector XA-C30 (optional)
Supplied with the CD/MD changer Sony BUS compatible CD/MD changer
Sony BUS compatible car audio Supplied with XA-C30 Supplied with the CD/MD changer
Sony BUS compatible CD/MD changer
Notes on using car battery adapter

Cautions

This unit is designed for 12 V DC negative earth operation only. To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not disassemble the unit. Refer servicing to qualified personnel only. Position the unit at a location that does not obstruct the operation of passenger-side airbag. While the unit is not in use, always disconnect it from the cigarette lighter socket. Do not place your CLITM handheld on an uneven surface while the car is moving. Otherwise, your CLI handheld may drop, resulting in possible damage. Be sure to take your CLI handheld out of the car when turning off the engine and leaving your car as the battery may drain. On installation Before installing the unit, please check your local traffic laws and regulations. Make sure to install the unit properly according to the installation manual. Improper installation may result in a fire or an electric shock. Before installation, be sure to turn the ignition switch to the OFF position or take out the key out. Installing the unit with the ignition on may cause battery drain or a short circuit. For information about the polarity, battery voltage and location of the airbag of your car, please consult your car dealer. Do not damage any pipes, tubes, the fuel tank or electric wiring when installing the unit, as a fire or accident may result. If you drill a hole in car panels, make sure that any hidden car parts will not be damaged. Do not use any nuts or bolts for critical devices such as steering linkage, fuel supply or braking systems. This can cause a fire or an accident. Take care to prevent the cords and wires from getting tangled or crimped in the moving portion of a seat rail. Do not use any car battery adapter other than the one supplied. Installing location Do not install the car cradle where: It will obstruct the drivers view when the car cradle is mounted in the car, or your CLIE handheld is in the car cradle. It will obstruct the operation of the airbag system. It will obstruct the operation of the vehicle, especially the steering wheel, shift lever, or brake pedal. It will be subjected to heat/high temperature (on a dashboard etc). Please consult a qualified technician or service personnel if you cannot attach the car cradle to the car securely.

Do not subject the unit to: Extreme heat or cold Dust, dirt, or sand High humidity Vibration Strong magnetic fields Mechanical shock Direct sunlight (for extended periods of time) Do not drop the unit. Disconnect the car battery adapter from the cigarette lighter socket when the engine is turned off. Be sure that nothing metallic comes into contact with the metal parts of this unit. If this happens, a short circuit may occur and the unit may be damaged. Do not operate the unit if it has a damaged cord or if it has been dropped or damaged. Always keep the metal contacts clean. Do not disassemble or convert the unit. While the unit is in use, it gets warm. This is normal. On cleaning Clean the unit with a soft, dry cloth or a soft cloth lightly moistened with a mild detergent solution. Do not use any type of solvent, such as alcohol or benzine, which may damage the finish.

Parts Iist (see fig.1)

The numbers in the list refer to those in the instructions. Choose the holding arm (2, 3 or 4), depending on the type of the CLI handheld. Short screen type (PEG-TG50)
Connection example (see fig.2)
Sony car audio units being compatible with PEGA-CC5 include:
Units with CD/MD changer control from 2004 forward Following units MEX-5DI, CDX-M1000TF, CDX-MP80, CDX-M850MP, CDX-M800, CDX-MP40, CDX-CA680X, CDX-MP70, CDX-MP30, CDX-M730, CDX-M630, CDX-CA900, CDX-CA700X, CDX-CA700, CDX-CA600X, CDX-CA600, MDX-CA790X, MDX-M690, MDX-CA680X, MDX-CA580, XR-CA670X, XR-CA370X, XR-CA370, XR-CA630X, XR-CA430X, XR-CA440, XR-CA600V, XR-CA600
Car cassette adapter connection (A) The car audio cassette player is necessary. Sony BUS compatible car audio connection (BFor connecting, the XA-CC1 connection adapter (optional) is necessary. )

2 holding arm (S)

Long screen type (PEG-NX73V)
Sony BUS compatible car audio and Sony BUS compatible CD/MD changer connection (B- ) For connecting, the XA-CC1 connection adapter (optional) and the XA-C30 source selector (optional) are necessary.
Connection diagram (see fig.3)
Note on car battery adapter qz connection 3 holding arm (L)
Insert the car battery adapter qz in the cigarette lighter socket only after all installation/connections have been done.

Long screen type 2 (PEG-TH55)

4 holding arm (L2)

Attaching condition A
less than 80 mm Dashboard section

more than 8 mm

Mounting support arm and rubber blocks
parallel fin air vent section side fin more than 6 mm less than 5 mm thick

Combination example 7 8

Mounting example
A Installing the mounting attachment
B Removing the mounting attachment

holding clip

9 or 0
Attaching the holding arms

Size S

>ABS<

1 2, 3 or 1

Detaching the holding arms

Size L

Size L2

RELEASE

2 holding arm (S) (PEG-TG50)
3 holding arm (L) (PEG-NX73V)
4 holding arm (L2) (PEG-TH55)
Mounting the car cradle to the mounting attachment
Attaching your CLITM handheld

Adjusting the angle

Attaching a GPS aerial A Attaching to the inside of a car

passenger-side airbag

Attaching to the outside of a car Roof B qs qf qs qf

Roof A

GPS aerial cord

qf qf qf qf

Connecting the car battery adapter
You can also fix the cord of the GPS aerial or the car battery adapter to the hooks on both sides of the mounting attachment.
13 Detaching your CLI handheld

cord hook

Precautions
Choose the installation location carefully, such that the unit will not interfere with normal driving operations. Avoid installing the unit in areas subject to dust, dirt, excessive vibration or high temperatures, such as in direct sunlight or near heater ducts under the floor carpet. Use only the supplied mounting hardware for a safe and secure installation.
B Removing the mounting attachment Press the lever on the bottom of the
mounting attachment. 2 Loosen the holding clip by pulling the mounting attachment forward. 1 Press the mounting attachment to the air vent. 2 Twist the mounting attachment slightly. 3 Pull the mounting attachment off towards you.
A Attaching to the inside of a car
Install the GPS aerial qs on the dashboard. Install the GPS aerial qs on a flat surface to keep it horizontal. Choose the attachment position where the best reception is achieved. Also, choose the position where no obstacle blocks the reception from the GPS satellite.

Note Some types of front windscreen do not let the radio wave from a GPS satellite pass. If the reception of the radio wave is poor when the GPS aerial qs is attached to the inside, attach it to the outside of the car roof.

2 Place cord.

Roof A Pass the GPS aerial cord over the roof, passing the windscreen pillar, fender and molding, and then pull it inside of the car.
Note Secure the cord with the cord clamps in the form of a U-shape to prevent rain water from entering the car along the cord.
Attaching condition (see fig.4)
This unit is attached to the dashboard of a car, and side fin of the air vent. The mounting attachment can be attached to an air vent whose dimensions and shape meet both conditions A and B. This unit cannot be attached to a circular air vent as in condition C.
Attaching the holding arms (see fig.7)
Depending on the type of the CLI handheld (short screen or long screen), choose the holding arm 2, the holding arm 3 or the holding arm 4. Short screen type (PEG-TG50) Size S is marked on the back of the holding arm 2. Long screen type (PEG-NX73V) Size L is marked on the back of the holding arm 3. Long screen type 2 (PEG-TH55) Size L2 is marked on the back of the holding arm 4. Size S
Roof B Pass the GPS aerial cord over the roof, passing the centre pillar, windscreen pillar inner side and dashboard, and then pull it into the car.
Notes Do not place the cord on the inside of the car if the car uses a curtain-type side airbag that spreads from the windscreen pillar over the centre pillar, or a shock-absorbing structure for its interior. Secure the cord using the cord clamps to make the cord form U-shape so that rain water does not enter into the car along the cord. Notes on GPS aerial Do not allow the cord to slack outside of the car. Depending on the car, the antenna cord may not be long enough to reach the roof. In this case, attach the GPS aerial to the inside of the car. Secure the cord of the GPS aerial with the cord clamps qf if necessary, to prevent the cord from disturbing driving. When detaching the GPS aerial, do not pull the cord. since the magnetic power is strong, the cord may detach. When washing your car by an automatic car-washing machine, detach the GPS aerial. Otherwise, the aerial may be detached during washing, and damage your car. GPS signals and DC power are flowing through the GPS aerial cord. When attaching the GPS aerial, be careful that the cord is not caught in any moving parts of the car. A damaged cord results in malfunction of the GPS aerial and the car cradle. Do not place the cord on the inside of the car if the car uses a curtain-type side airbag that spreads from the windscreen pillar over the centre pillar, or a shock-absorbing structure for its interior. For details, please consult qualified technician or service personnel.

Before attachment Make sure that the GPS aerial qs has good reception and not hidden behind car ornaments, the windscreen wiper, etc. Make sure that the GPS aerial qs does not disturb operation of car equipment. Clean the mounting surface.
1 Remove the release-coated paper from the
Mounting support arm and rubber blocks (see fig.5)
Combining the support arm 6and the support arm 7 with rubber blocks 8, attach them to the mounting attachment 5. Depending on the dimensions and shape of the dashboard and the air vent, choose the support arms so that the rubber blocks 8 are placed on the top and bottom outer edges of the air vent.
Notes Choose a combination of rubber blocks 8, the support arm 6 and the support arm 7 so that the rubber blocks 8 do not block the air vent. Depending on the dimensions and shape of the dash board and the air vent, the mounting attachment 5 can sometimes be attached without the support arm 6 or the support arm 7.
surface of the base sheet qd, and then place the GPS aerial qs on the centre of the base sheet qd.
Place the GPS aerial qs on the centre of the base sheet qd.
1 Remove the sheet attached to the car cradle.
When removing the sheet, be careful not to let any objects get into the slots of the car cradle.
2 Attach the holding arms chosen according to
the type of CLI handheld. 1 Insert the holding arms tab into the car cradle. 2 Pull both sides of the holding arms outwards and insert the tab. Detaching the holding arms When replacing the holding arms to use the different type of CLI handheld, etc., insert the tip of a slotted screwdriver into the slot for the tab and release the lock of the tab. There are two tabs: one on the left and one on the right.
2 Remove the release-coated paper from the
back surface of the base sheet qd, and stick the base sheet qd to the mounting surface.
Installing the mounting attachment (see fig.6)
A Mounting the mounting attachment.
Choose either the holding clip (S) 9 or the holding clip (L) 0, depending on the width of the side fin of the air vent.
Mounting the car cradle to the mounting attachment (see fig.8)
1 Slide the tip of the mounting attachment along the rail on the back of the car cradle to mount it. 2 Rotate the dial to fix the car cradle.
To mounting surface Notes Fix the cord to the position that does not obstruct the operation of passenger-side airbag. Fix the cord of the GPS aerial qs using the cord clamps qf if necessary, to prevent the cord from disturbing driving. If the cord tangles up the gearshift, etc., it is extremely dangerous. Attach the cord clamps qf after cleaning the mounting surface.

On painting of the GPS aerial The GPS aerial qs can be painted to match the cars body colour. However, do not use metallic paint, as it may cause poor reception or reception error. Also, when painting, do not dismantle the aerial.
Insert the holding clip into the air
vent and hook the holding clip on the side fin. 2 Adjust the attachment position so that the holding clip does not touch the back fin. If you insert the holding clip forcibly, the back fin may be damaged.
Note Setting the holding clip and the side fin parallel, attach the mounting attachment.
Connecting the car battery adapter (see fig.qs)
Connect the car battery adapter qa to the DC 5.2V connector of car cradle (1), and connect the car battery adapter qa into the cigarette lighter socket (2).
Notes Do not plug the car battery adapter qa into the cigarette lighter socket immediately after using the cigarette lighter. First allow the socket to cool down. To fix the cord of the car battery adapter qa, use the cord clamps qf if necessary. Clean the mounting surface before attaching the cord clamps.
Attaching your CLI handheld (see fig.9)
Mounting 1 Mount your CLI handheld on the connector of the car cradle. 2 Tilt back your CLI handheld rest in the car cradle.
Note Do not mount your CLI handheld while driving.
B Attaching to the outside of a car
Attach the GPS aerial qs horizontally in a place where GPS satellite reception is not blocked by the car roof. The GPS aerial qs is attached by a magnet. When attaching it on the car, place it carefully, so as not to harm the cars body surface. When attaching to a car of aluminum or FRP body Since the magnet will not stick to aluminum or FRP, attach the GPS aerial qs to the inside of the car. Before attachment Clean the mounting surface.
2 With the holding clip hooked on the side fin
of the air vent, feed the holding clip into the hole on the back of the mounting attachment, and pull the holding clip until the mounting attachment becomes stable.
Tip (6-*) If the rubber blocks 8 of the car cradle slip and the car cradle cannot be attached to the dashboard securely, attach it using the two-sided tape qg between the rubber blocks 8 and the dashboard. The two-sided tape qg can be cut. Cut it to a size larger than the rubber block 8 itself. The two-sided tape qg is ineffective if it is cut too small. Please consult a qualified technician or service personnel if you cannot attach the car cradle to the car securely. Notes If you pull the holding clip too firmly, the fin of the air vent may be damaged. If the air vent fin is set to swing automatically, stop it before mounting the mounting attachment. By doing the following, make sure that the mounting attachment and the holding clip are attached securely and do not vibrate. Pull the mounting attachment lightly and push it up and down. Push and pull the mounting attachment against the air vent.

Adjusting the angle (see fig.0)
Adjust the angle of the car cradle by dial mounting attachment. of the
Detaching your CLI handheld (see fig.qd)
Detaching 1 Squeeze both RELEASE buttons simultaneously with one hand. 2 Pull out the CLI handheld towards you from the top with your other hand.
Notes Do not detach your CLI handheld from the car cradle with one hand, it may cause a malfunction. Do not detach your CLI handheld while driving.
1 Attach the GPS aerial qs to the roof.
Attaching a GPS aerial (see fig.qa)
Clean the mounting surface before attaching.

Dashboard Roof B Roof A