XTL-750W/XVM-750WEX

SERVICE MANUAL

AEP Model UK Model

Monitor : XVM-753W
This set consists of the following units.
XTL-750W MONITOR HIDEAWAY UNIT REMOTE COMMANDER ANTENNA XVM-753W XT-993V RM-X86 VCA-114 XVM-750WEX XVM-753W XA-602
The XTL-750W has a monitor change to the XTL-6100MK2. The XVM-750WEX has a monitor change to the XVM-61EX. This service manual only describes the monitor and accessories and packing materials. Refer to the service manual for XTL-6100MK2 (9-926-587-11) for information on the hideaway unit XT-993V. Refer to the service manual for XVM-61EX/6100 (9-925-661-11) for information on the hideaway unit XA-602.

SPECIFICATIONS

Monitor (XVM-753W)
System Display Drive system Picture size Liquid crystal color display Transparent TN LCD panel TFT active matrix system 7 in.; 155.52 87.75 mm, 178.57 mm (w h, diagonally) Wireless remote (RM-X86: XTL-750W) Power requirements AA (R6) battery 2 Operable range Approx. 3 m Dimensions 115 mm (w h d) Mass Approx. 100 g (including batteries)

Picture segment

336,960 (w 1440 h 234) Speaker type mm dynamic speaker 2 Power requirements 12 V DC car battery (negative ground) Current drain Approx. 1.0 A Dimensions 215 126.mm (w h d) Operating temperature 5C ~ +45C Mass Approx. 650 g

Continued on next page

MOBILE COLOR TV

XTL-750W

EXTENSION MONITOR SYSTEM

XVM-750WEX

MICROFILM
TV aerial (VCA-114: XTL-750W) Cord 5 m, 75 ohm Supplied accessories Wireless remote RM-X86 (1) (XTL-750W) Power input cord (1) (XTL-750W) Monitor cable (1) TV aerial VCA-114 (1) (XTL-750W) Parts for installation and connections (1 set) (XTL-750W) Mounting kit (1 set) (XTL-750W)
TABLE OF CONTENTS 1. GENERAL
Location of Controls... 3 Getting Started.. 3 Watching a TV Programme.. 3 Viewing the Wide Screen.. 4 Watching a Video... 4 Listening to the TV/video Sound with the Picture Off... 4 Adjusting the Picture.. 5 Adjusting the Screen Brightness.. 5
Design and specifications are subject to change without notice.
2. DISASSEMBLY Notes on Chip Component Replacement
Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. 2-1. Rear Panel Assy... 6 2-2. Main Board.. 6
3. ELECTRICAL ADJUSTMENTS.. 7 4. DIAGRAMS
4-1. 4-2. 4-3. 4-4. Block Diagram Monitor Section. 9 Printed Wiring Boards Monitor Section.. 10 Schematic Diagram Monitor Section (1/2). 12 Schematic Diagram Monitor Section (2/2). 13

5. EXPLODED VIEW

5-1. Monitor Section (XVM-753W).. 15
6. ELECTRICAL PARTS LIST.. 16

SECTION 1 GENERAL

This section is extracted from XTL-750Ws instruction manual.

SECTION 2 DISASSEMBLY

Note : Follow the disassembly procedure in the numerical order given.

2-1. REAR PANEL ASSY

1 screws (2.6x5)

2 screws (2.6x5)

4 stand bracket (W) 3 screws (2.6x5)
5 screws (M2x6), tapping qs rear panel assy 6 screws (M2x6), tapping 7 CN601

8 CNCN301

0 connector

qa CN302

2-2. MAIN BOARD

5 screws (M2x6), tapping

switch
7 sheet 3 Unsolder. 6 screws (M2x6), tapping

1 screw (M2x6), tapping

8 MAIN board

4 MONITOR SUB board

2 CN101
SECTION 3 ELECTRICAL ADJUSTMENTS

MONITOR SECTION

Equipment Used The measuring equipment below are used for these electrical adjustments: Oscilloscope NTSC pattern generator Regulated DC power supply Digital voltmeter Connection of Equipment Unless otherwise specified, the measuring equipment should be connected as shown below: Inverter Voltage Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect a digital voltmeter to TP64 on the MONITOR MAIN board. 3. Adjust RV601 so that the reading on the digital voltmeter is 7.80 0.05 V. Adjustment Location: See page 8. Bright Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect a digital voltmeter to TP70 on the MONITOR MAIN board. 3. Adjust RV201 so that the reading on the digital voltmeter is 2.13 0.02 V. Adjustment Location: See page 8. VCOM Adjustment (1) Procedure: 1. Display the gray scale on the monitor screen. 2. Connect an oscilloscope to TP102 on the MONITOR MAIN board. 3. Adjust RV210 so that the amplitude of the output waveform is 7.5 0.1 Vp-p. 4. Adjust RV211 so that the level A of the output waveform is at 5.5 0.05V DC.
INPUT (1) (VIDEO) NTSC pattern generator

MONITOR OUT Hideaway unit XT-993V Monitor XVM-753W
VIDEO OUT (75 ) Parking ACC cord
Regulated DC power supply

7.5Vp-p

Setup for Adjustment The adjustment signal is a 5-step gray scale signal from a NTSC pattern generator. Input the gray scale signal into the tuner unit and connect an oscilloscope to TP14 on the MONITOR MAIN board. Check that the width between the black and white levels of the gray scale signal is 0.74 Vp-p.
Adjustment Location: See page 8. RGB Amplitude Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect a digital voltmeter to TP63 on the MONITOR MAIN board. 3. Adjust RV208 so that the reading on the digital voltmeter is 2.37 0.02 V. Adjustment Location: See page 8. 2 Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect a digital voltmeter to TP67 on the MONITOR MAIN board. 3. Adjust RV213 so that the reading on the digital voltmeter is 2.19 0.02 V. Adjustment Location: See page 8.

white 0.74Vp-p black

DC/DC Converter Voltage Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect a digital voltmeter to TP57 on the MONITOR MAIN board. 3. Adjust RV401 so that the reading on the digital voltmeter is 5.35 0.05 V. Adjustment Location: See page 8.
0 Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect an oscilloscope to TP106 on the MONITOR MAIN board. 3. Adjust RV212 so that the white level of the waveform is at 4.6 0.05V DC. Adjustment Location: Monitor Main Board R and B Level Adjustment Procedure: 1. Display the gray scale on the monitor screen. 2. Connect an oscilloscope to TP107 on the MONITOR MAIN board. 3. Adjust RV207 so that the white level of the waveform is at 4.6 0.05V DC. 4. Connect an oscilloscope to TP108 on the MONITOR MAIN board. 5. Adjust RV209 so that the white level of the waveform is at 4.4 0.05V DC. Adjustment Location: Monitor Main Board Adjustment Location:
VCOM Adjustment (2) Procedure: 1. Display the navigation map screen on the monitor screen. 2. Adjust RV211 so as to ensure that the screen has the highest contrast with no flicker. Adjustment Location: Monitor Main Board
MONITOR MAIN BOARD (SIDE A)

2 RV211 RV210 RV213

0 RV212
RV208 RV401 RV209 RV207 RV201 RGB DC/DC BRIGHT AMPLITUDE CONVERTER R AND B LEVEL VOLTAGE

RV601 INVERTER VOLTAGE

MONITOR MAIN BOARD (SIDE B)

TP108 TP70 TP107 TP106

TP67 TP102

TP14 TP63 TP57

XTL-750W/XVM-750WEX SECTION 4 DIAGRAMS
4-1. BLOCK DIAGRAM MONITOR SECTION

CN1 AUDIO (MAIN) 3 D301

AUDIO POWER AMP IC6 1
CN1 SP1 MAIN/L SPEAKER KEY IN MATRIX IC102 B+ (5V)
CNSIRCS 1 REMOTE CONTROL SENSOR IC101
B+ (AMP) AUDIO POWER AMP IC303 AUDIO (SUB) 2 DCNSP2 SUB/R SPEAKER
S101 NAVI S102 TV/VIDEO 2 D102 POWER

S14 OSC 2 SOSC 1 SOUT K0 K1 K9 7
S103 SEARCH (+) S104 SEARCH ()
X101 480kHz MIX/ BUFFER Q102, 103 AMP Q101

B+ (AMP)

S107 VOL (+) S108 VOL ()

RV213 GAMMA27

RV212 GAMMA0

RV201 BRIGHT

RV207 R SUB BRIGHT

RV209 B SUB BRIGHT

RV208 RGB AMP

BRIGHT

Signal path : TV and External Video (AUDIO) : NAVI (AUDIO) : VIDEO

CNVR VG VB

B+ (5V) DGAMMA AMP INV AMP V COM AMP IC7

R IN G IN B IN

INT/ EXT SW

C. SYNC

S1 POWER

SYNC SEP

38 BGP GEN BGP 37
V COM BIAS Q207-210 RV211 V COM DC PAL/NTSC CONTROL Q104

HIDEAWAY UNIT POWER SW 8

VIDEO INTERFACE, LED DRIVER IC201

RV210 V COM AMP

4 INV IC1
FRPT FRPV VCS SYN HSY LIQUID CRYSTAL DISPLAY LCD1

WIDE MODE1 (PAL/NTSC)

16 +B Q1CK S105 SELECT 6 FWIDE MODE SELECT 1Q IC103 2Q 1CLR 2CLR DC-DC CONVERTER TRANSFORMER T501 D502 D503 L501 B+ (13V) L502 B+ (7.5V) D504 F501 F601 B+ SWITCH Q608 B+ ON/OFF Q606,607 L602 ERROR AMP 3 COMP ERROR AMP 7 COMP T601 BL B+ ON/OFF Q602 REG Q604 BL DRIVE Q601 SWITCH Q611 INVERTER Q609, RV401 5V PWM L505 DC-DC CONVERTER IC401 D505 DC-DC CONVERTER Q502-504 L503 B+ (5V) L504 B- (-5V) D506 L513 B- (-16V) L511 L510 L11 MODW MODN VGH VSH NTP HRV VRV CLKC MODS VGL

REG IC302

BUFFER Q603, 605
CN2 HV GND BACK LIGHT UNIT1

BL OFF/ON

BL CONTROL Q801, 802
COMPARATOR IC601 DIMMER DISCRIMINATOR IC7 S701 DIMMER AUTO HIGH 5 T602
CN2 HV GND BACK LIGHT UNIT2

D701 DIMMER SENSOR

4-2. PRINTED WIRING BOARDS MONITOR SECTION
Semiconductor Location (side A) Ref. No. D101 D104 D105 D106 D107 D108 D109 D110 D111 D112 D113 D201 D202 D203 D204 D502 D503 D504 D505 D506 D601 D602 D603 D701 D702 D801 D802 IC102 IC201 IC301 IC303 IC601 IC701 Q101 Q102 Q103 Q104 Q207 Q208 Q209 Q210 Q502 Q503 Q504 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q609 Q610 Q801 Q802 Location E-7 E-8 E-8 E-7 E-7 F-7 E-7 E-7 E-8 E-7 E-7 D-4 C-5 C-4 C-5 E-4 E-4 E-4 D-4 D-4 E-9 D-9 D-8 F-7 E-6 E-6 D-6 E-7 A-7 E-2 E-1 D-9 E-6 E-8 E-8 E-9 B-5 C-5 C-5 B-5 B-5 E-3 D-3 F-3 D-8 E-8 E-9 E-8 D-9 E-9 E-9 A-8 C-8 D-6 E-7
Note: Y : parts extracted from the conductor side. z : Through hole. b : Pattern from the side which enables seeing. (The other layers patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.

Semiconductor Location (side B) Ref. No. D1 D2 D301 D302 D604 D605 IC103 IC203 IC204 IC302 IC401 Q105 Q608 Q611 Location F-11 D-1 C-1 C-1 D-9 E-10 E-7 C-6 B-6 D-2 E-3 F-7 E-9 D-10
4-3. SCHEMATIC DIAGRAM MONITOR SECTION (1/2) Refer to page 14 for IC Block Diagrams.
Note: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. C : panel designation. U : B+ Line. V : B Line. H : adjustment for repair. CN1 of XVM-753W is connected to CN3 (MONITOR OUT) of Hideaway Unit (XT-993V) with a monitor cable. Power voltage is dc 14.4 V from ACC cord of the Hideaway Unit and fed with regulated dc power supply. (XVM-753W) CN1 of XVM-753W is connected to CN3 (MONITOR OUT) of Hideaway Unit (XT-993V) with a monitor cable. Voltage and waveforms are measured at input the color bar signal from INPUT 1 VIDEO (J5-3) jack of the Hideaway Unit. (XVM-753W) Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : TV and External Video (AUDIO) J : NAVI (AUDIO) c : VIDEO

(Page 11)

4-4. SCHEMATIC DIAGRAM MONITOR SECTION (2/2) Refer to page 14 for IC Block Diagrams. Waveforms

5.0Vp-p H

1.0Vp-p H

(Page 12)

7.0Vp-p 23.5sec

B Q610 B

44Vp-p 23.5sec

C Q610 C

IC Block Diagrams IC102 BU2486-46

OSC1 OSC2 VDD OUT

IC201 IR3Y29B4
VCO OUT APC FILTER B OUT VCC2 G DC DET R DC DET VCO IN 14 VCO G OUT R OUT GND2 GND1
OSC OSC1 INSTRUCTION DECODER ROM 64WORD x 16PAGE x 8BIT 64 DECODER 6 PC 6 STACK 2LEVEL PA 4 STACK 2LEVEL 16 DECODER 8

S-LATCH 7

B DC DET 25 GAMMA GAMMA RGB AMPLITUDE 28 ADJUST INV INV INV

CARRIER GEN

S7 S6 S3 S2

DECODER

RAM 16WORD x 2PAGE x 4BIT

SYNC IN

PAL SW

PHASE SHIFT

12 CHROMA OUT
P P N 10 B-Y 9 R-Y 8 KILLER FILTER P N P N 11 ACC FILTER

Y-REG 4 ACC

BRIGHT 29 SUB BRIGHT B 30 SUB BRIGHT R 31

RESET 1

INT/EXT SW

K0 K1 K2 K3

WATCH DOG TIMER

KILLER

Y MATRIX R-Y COMMON 32 FRP FRP 33 G-Y B-Y

R-Y G-Y B-Y

PAL ON HPF

7 BURST OUT 6 COLOR

AGC DET N COMP

WINDOW PULSE GEN

IC401 TL1451ACNS
DEAD TIME CONTROL2 NON-INVINPUT2 INVINPUT2 FEED BACK2

IC103 TC74HC107AF

F/F SYNC IN 34

BGP BGP GEN P

2K 2CLR

REF OUT

1CLK 1CK

2CR 2J

PICTURE
16 VREF +2.5V VCC REFERENCE VOLTAGE +2.5V SHORT CIRCUIT PROTECTION COMPARATOR + + VREF/2
5 C IN 4 IDENT FILTER 3 VIDEO IN
ERROR AMP2 VREF VREF VREF

PWM COMPARATOR2

J CK K CLK Q Q

K CK J CLK Q Q

SYNC OUT 35

SYNC SEP 36

2 CONTRAST 1 TRAP AGC AMP AGC DET CLAMP COMP

OUTPUT2

OUTPUT1 S R LATCH R U.V.L.O PWM COMPARATOR1
43 B IN G IN R IN VCC1 SW

44 F ADJ

45 CLAMP

AGC FILTER AGC OUT

48 PICTURE
TRIANGLE OSCILLATOR 1 CT 2 RT 3 NON-INVINPUTINVINPUT1
+ ERROR AMP1 GND 5 FEED BACKDEAD TIME CONTROLOUTGND
COMMON AMPLITUDE ADJUST COMMON OUT

SECTION 5 EXPLODED VIEW

NOTE: The mechanical parts with no reference number in the exploded views are not supplied. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. -XX and -X mean standardized parts, so they may have some difference from the original one. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE). (RED) R R Parts Color Cabinets Color Accessories and packing materials are given in the last of this parts list.
5-1. MONITOR SECTION (XVM-753W)

LCD1 SP1

Ref. No. 1 * * * 8 * Part No. X-3378-483-1 3-018-155-01 3-018-974-01 3-014-835-01 3-713-790-21 3-016-188-01 1-782-596-11 A-3317-721-A 1-666-548-11 X-3377-550-1 Description PANEL ASSY, FRONT SHEET (MAIN PC BOARD) SCREW (2X5) BRACKET (W), LCD SCREW (M2X6), TAPPING, P3 SCREW (2.6X5) CABLE, FLAT 24P MONITOR MAIN BOARD, COMPLETE MONITOR SUB BOARD PANEL ASSY, REAR
Remark Ref. No. * * * * 15 Part No. 3-014-834-01 3-019-224-01 3-020-033-01 3-020-466-01 3-018-154-01 3-019-040-01 1-801-725-11 1-505-588-11 1-505-588-11 Description BRACKET (W), STAND SHEET (EMBLEM) CUSHION (VOL) SHEET (FP2) SHEET (BRACKET) SHEET DISPLAY PANEL, LIQUID CRYSTAL SPEAKER (3.5X2cm) (L-CH) SPEAKER (3.5X2cm) (R-CH) Remark

* 16 LCD1 SP1 SP2

MONITOR MAIN
NOTE: Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable

SECTION 6 ELECTRICAL PARTS LIST
Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : , for example: uA. : A. uPA. : PA. uPB. : PB. uPC. : PC. uPD. : PD. CAPACITORS uF : F COILS uH : H When indicating parts by reference number, please include the board.

Ref. No. *

Part No.

Description

Remark
Ref. No. C312 C313 C315 C316 C317
Part No. 1-162-970-11 1-162-970-11 1-104-652-11 1-165-128-11 1-216-833-11 1-162-966-11 1-164-346-11 1-164-739-11 1-164-392-11 1-162-967-11 1-164-156-11 1-162-967-11 1-164-392-11 1-164-156-11 1-216-295-00 1-165-128-11 1-163-127-00 1-124-943-11 1-117-154-11 1-109-894-11 1-109-894-11 1-124-943-11 1-124-569-11 1-124-577-11 1-124-577-11 1-126-968-11 1-124-943-11 1-126-177-11 1-128-078-11 1-128-078-11 1-124-943-11 1-164-227-11 1-164-227-11 1-162-970-11 1-162-970-11 1-126-157-11 1-164-227-11 1-162-970-11 1-164-346-11 1-128-528-11 1-162-970-11 1-117-930-11 1-107-526-11 1-128-528-11 1-107-526-11
Description CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP RES-CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP SHORT CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP FILM CHIP CERAMIC CHIP ELECT CERAMIC CHIP 0.01uF 0.01uF 470uF 0.22uF 10K 0.0022uF 1uF 560PF 390PF 0.0033uF 10% 10% 20% 5% 10% 5% 5% 10%
Remark 25V 25V 10V 16V 1/16W 50V 16V 50V 50V 50V 25V 50V 50V 25V
A-3317-721-A MONITOR MAIN BOARD, COMPLETE ****************************** < CAPACITOR > C1 C103 C104 C201 C202 C203 C204 C205 C206 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C225 C226 C227 C228 C231 C232 C233 C234 C235 C236 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 1-164-506-11 1-164-156-11 1-117-720-11 1-164-156-11 1-164-156-11 1-164-156-11 1-126-157-11 1-164-346-11 1-164-217-11 1-164-346-11 1-164-346-11 1-124-589-11 1-164-346-11 1-164-346-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-164-156-11 1-162-969-11 1-126-320-11 1-162-970-11 1-126-320-11 1-162-913-11 1-124-589-11 1-126-155-11 1-163-021-11 1-216-105-11 1-165-176-11 1-165-176-11 1-164-346-11 1-164-346-11 1-165-128-11 1-165-176-11 1-165-176-11 1-164-346-11 1-126-968-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 4.7uF 0.1uF 4.7uF 0.1uF 0.1uF 0.1uF 10uF 1uF 150PF 1uF 1uF 47uF 1uF 1uF 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF 16V 25V 10V 25V 25V 25V 16V 16V 50V 16V 16V 16V 16V 16V 25V 25V 25V 25V 25V 25V 25V 25V 25V 16V 25V 16V 50V 16V 6.3V 50V 1/10W 16V 16V 16V 16V 16V 16V 16V 16V 16V

C318 C319 C401 C402 C403 C404 C405 C406 C407 C408 C410 C501 C502 C503 C504 C505 C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C601 C602 C603 C604 C605 C606 C607 C609 C610 C611 C612 C613 C614 C615

20% 5%

0.1uF 0.0033uF 10% 390PF 5% 0.1uF 0 0.22uF 270PF 39uF 33uF 33uF 33uF 39uF 56uF 82uF 82uF 100uF 39uF 100uF 33uF 33uF 39uF 0.022uF 0.022uF 0.01uF 0.01uF 10uF 0.022uF 0.01uF 1uF 470uF 0.01uF 0.22uF 22PF 470uF 22PF
10% 10% 10% 10% 10% 10% 10% 10% 20% 10% 20% 0.5PF 20% 20% 10% 5% 10% 10%
5% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 10% 10% 10% 10% 20% 10% 10% 20% 10% 10% 10% 20% 10%
16V 50V 25V 16V 10V 10V 25V 16V 10V 10V 16V 25V 10V 25V 25V 25V 25V 25V 25V 25V 16V 25V 25V 16V 16V 25V 100V 3KV 16V 3KV
CERAMIC CHIP 0.01uF CERAMIC CHIP 0.1uF CERAMIC CHIP 0.0068uF ELECT,NONPOLAR10uF CERAMIC CHIP 0.01uF ELECT,NONPOLAR10uF CERAMIC CHIP 8PF ELECT 47uF ELECT 100uF CERAMIC CHIP 0.01uF RES-CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 220K 0.047uF 0.047uF 1uF 1uF 0.22uF 0.047uF 0.047uF 1uF 100uF

10% 10% 20%

Ref. No. C701 C702 C703 C801 C901 Part No. 1-165-112-11 1-162-970-11 1-164-346-11 1-128-078-11 1-128-528-11 Description CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT < CONNECTOR > CN1 CN8 * CN101 * CN301 * CN302 * CN601 * CN602 1-695-022-21 1-569-629-11 1-580-057-11 1-580-055-21 1-580-055-21 PLUG, CONNECTOR 16P HOUSING, CONNECTOR 24P PIN, CONNECTOR (SMD) 4P PIN, CONNECTOR (SMD) 2P PIN, CONNECTOR (SMD) 2P 0.33uF 0.01uF 1uF 33uF 470uF 10% 20% 20% Remark 16V 25V 16V 16V 16V Ref. No. F901 Part No. Description Remark 1-533-950-21 FUSE, CHIP (2A) < IC > IC102 IC103 IC201 IC203 IC204 IC301 IC302 IC303 IC401 IC601 IC701 < DIODE > < COIL > D1 D2 D101 D104 D105 D106 D107 D108 D109 D110 D111 D112 D113 D201 D202 D203 D204 D301 D302 D502 D503 D504 D505 D506 D601 D602 D603 D604 D605 D701 D702 D801 D802 8-719-422-64 8-719-073-01 8-719-422-64 8-719-941-86 8-719-941-86 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-941-23 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-422-64 8-719-941-09 8-719-941-09 8-719-938-75 8-719-941-09 8-719-941-09 8-719-941-09 8-719-422-64 8-719-422-76 8-719-048-98 8-719-048-98 1-528-925-21 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE MA8062-M-TX MA111-TX MA8062-M-TX DAN202UT106 DAN202UT106 MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX DA204UT106 MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX MA8062-M-TX DAP202UT106 DAP202UT106 SB05-05CP-TB DAP202UT106 DAP202UT106 DAP202UT106 L501 L502 L503 L504 L505 L506 L507 L508 L509 L510 L511 L512 L513 L601 L602 L603 1-412-032-11 1-412-032-11 1-414-862-11 1-412-032-11 1-411-294-21 1-412-031-11 1-412-031-11 1-412-031-11 1-412-031-11 1-412-031-11 1-412-031-11 1-412-031-11 1-412-032-11 1-415-929-21 1-415-929-21 INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR CHIP INDUCTOR INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR 100uH 100uH 82uH 100uH 150uH 47uH 47uH 47uH 47uH 47uH 47uH 47uH 100uH 100uH 100uH 100uH 8-759-462-41 8-759-293-00 8-759-450-52 8-759-100-96 8-759-031-84 8-759-701-02 8-759-170-92 8-759-701-02 8-759-937-36 8-759-337-40 IC IC IC IC IC IC IC IC IC IC BU2486-46-E2 TC74HC107AF(TP1) IR3Y29B4 NJM4558M-T1 TC7S04F-TE85L NJM2073M-T1 PQ09SZ1T NJM2073M-T1 TL1451ACNSR NJM2904V(TE2)

MONITOR SUB

1-666-548-11 MONITOR SUB BOARD ******************* < CAPACITOR > C101 1-162-970-11 CERAMIC CHIP < DIODE > D102 8-719-987-02 LED CL-140PG-CD-T (POWER) < IC > IC101 8-749-925-07 IC RS-30E-T < RESISTOR > 0.01uF 10% 25V
R102 1-216-818-11 METAL CHIP 560 5% 1/16W ************************************************************* MISCELLANEOUS *************** 7 1-782-596-11 CABLE, FLAT 24P LCD1 1-801-725-11 DISPLAY PANEL, LIQUID CRYSTAL SP1 1-505-588-11 SPEAKER (3.5X2cm) (L-CH) SP2 1-505-588-11 SPEAKER (3.5X2cm) (R-CH) ************************************************************* ACCESSORIES & PACKING MATERIALS ******************************** 1-473-715-51 REMOTE COMMANDER (RM-X86) (750W) 3-042-789-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN) (750W) 3-042-790-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,GERMAN) (750W) 3-042-793-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN) (750WEX) 9-939-691-01 LID, BATTERY CASE (for RM-X86) (750W) *************************************************************
< CERMET RESISTOR > RV201 RV207 RV208 RV209 RV210 RV211 RV212 RV213 RV401 RV601 1-238-088-11 1-238-092-11 1-238-092-11 1-238-092-11 1-238-092-11 1-238-090-11 1-238-092-11 1-238-092-11 1-238-088-11 1-238-087-11 RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET RES, ADJ, CERMET < SWITCH > S1 S101 S102 S103 S104 S105 S107 S108 S701 1-692-088-51 1-692-088-51 1-692-088-51 1-692-088-51 1-692-088-51 1-692-088-51 1-572-499-11 1-572-499-11 1-572-834-21 SWITCH, TACTILE (POWER) SWITCH, TACTILE (NAVI) SWITCH, TACTILE (TV/VIDEO) SWITCH, TACTILE (SEARCH +) SWITCH, TACTILE (SEARCH ) SWITCH, TACTILE (SELECT) SWITCH, TACTILE (VOL +) SWITCH, TACTILE (VOL ) SWITCH, SLIDE (DIMMER) < TRANSFORMER > T501 T601 T602 1-431-250-11 TRANSFORMER, DC-DC CONVERTER 1-431-306-11 TRANSFORMER, INVERTER 1-431-306-11 TRANSFORMER, INVERTER < VIBRATOR > X101 1-767-037-21 VIBRATOR, CERAMIC (480kHz) ************************************************************* 2.2K 47K 47K 47K 47K 10K 47K 47K 2.2K 1K

Ref. No.

PARTS FOR INSTALLATION AND CONNECTIONS *************************************** vA vB 3-310-656-01 TAPE, MAGIC (750W) 3-310-658-01 TAPE (B), MAGIC (750W) 1-777-901-11 CORD (WITH CONNECTOR) (POWER) (2m) (including vA) (750W) 1-777-317-11 CORD, CONNECTION (16P-16P) (3m) (MONITOR EXTENSION) 1-690-814-11 CORD (WITH TERMINAL) (EARTH) (750W) 1-695-529-11 CONNECTOR (RELAY) (750W) X-3374-113-1 STAND ASSY (750W) 7-685-661-79 SCREW +P 4X12 TYPE4 (750W) 3-938-291-01 COVER (STAND) (750W) NOT SUPPLIED CLEANING CLOTH (750W) 3-389-594-01 CLAMP, CORD (for MONITOR) (750W) 1-754-015-11 ANTENNA, TV (VCA-114) (5m) (including vB) (750W) 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) 3A (750W) 1-532-414-11 FUSE (1A/125V) (750W)

9-870-027-11

Sony Corporation
Mobile Electronics Division Company
99L047540-1 Printed in Hungary 1999. 12 Published by General Engineering Dept.

Specifications

Monitor (XVM-611EX)
System Display Drive system Picture size Liquid crystal color display Transparent TN LCD panel TFT active matrix system 6 in.; 121.9 89.2 mm, 151 mm (w h, diagonally) Picture segment 224,640 (w 960 h 234 ) Speaker type 5 cm dynamic speaker Power requirements 12 V DC car battery (negative ground) Current drain Approx. 0.7 A Dimensions 31 mm (w h d) Operating temperature +5 C ~ +45 C Mass Approx. 430 g

Especificaciones

Sistema Pantalla de color de cristal lquido Pantalla Panel LCD TN transparente Sistema de activacin Matriz activa TFT Tamao de imagen 6 pulgadas; 121,9 89,2 mm, 151 mm (an al, en diagonal) Segmento de imagen 224.640 (an 960 al 234 ) Tipo de altavoz Dinmico, 5 cm Requisitos de alimentacin batera de automvil de 12 V CC (masa negativa) Drenaje de corriente Aprox. 0,7 A Dimensiones 31 mm (an al prf) Temperatura de funcionamiento +5 C ~ +45 C Masa Aprox. 430 g

Technische Daten

System Display Anzeigesteuerung Bildgre Bildelemente Lautsprechertyp Stromversorgung Flssigkristallfarbbildschirm Transparente TN-LCDAnzeige TFT-Aktivmatrix 121,9 89,2 mm, 151 mm (B H, Diagonale) 224.640 (B: 960 H: 234 ) Dynamischer Lautsprecher, 5 cm Autobatterie mit 12 V Gleichstrom (negative Erdung) ca. 0,7 A 31 mm (B H T) +5 C ~ +45 C ca. 430 g
Warning Advertencia Achtung
To prevent fire or shock hazard, do not expose the unit to rain or moisture. Para evitar incendios o descargas, no exponga la unidad a la lluvia ni a la humedad. Um Feuergefahr und die Gefahr eines elektrischen Schlags zu vermeiden, setzen Sie das Gert weder Regen noch sonstiger Feuchtigkeit aus.
Stromentnahme Abmessungen Betriebstemperatur Gewicht

Supplied accessories

Monitor cable (1) Hideaway unit (1)

Mitgeliefertes Zubehr

Monitorkabel (1) Abdeckung (1)
Design and specifications are subject to change without notice.

Accesorios suministrados

Cable de monitor (1) Unidad ocultable (1)
nderungen, die dem technischen Fortschritt dienen, bleiben vorbehalten. El diseo y las especificaciones estn sujetos a cambio sin previo aviso. (1)

Location of Controls

Ubicacin de los controles
Lage und Funktion der Teile und Bedienelemente
Adjusting the Screen Brightness
Depending on the surrounding light, you can adjust the screen brightness by controlling the brightness of the fluorescent pipe installed in the liquid crystal panel. Change the DIMMER selector located on the side of the monitor to HIGH or LOW. To adjust, use the BRIGHT dial.