USER GUIDE

Soundcraft Notepad User Guide
IMPORTANT Please read this manual carefully before using your mixer for the first time.
This equipment complies with the EMC Directive 2004/108/EC and LVD 2006/95/EC

soundcraft@harman.com

Harman International Industries Ltd. 2009 All rights reserved Parts of the design of this product may be protected by worldwide patents. Part No. BD10.534000 Issue 1109 Soundcraft is a trading division of Harman International Industries Ltd. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Soundcraft shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Soundcraft.
Harman International Industries Limited Cranborne House Cranborne Road POTTERS BAR Hertfordshire EN6 3JN UK Tel: +44 (0)Fax: +44 (0)http://www.soundcraft.com

Contents

IMPORTANT SAFETY INSTRUCTIONS SAFETY SYMBOL GUIDE INTRODUCTION THE 60-SECOND GUIDE WIRING UP BLOCK DIAGRAMS MONO INPUT CHANNELS STEREO INPUT CHANNELS MASTER SECTION FX PROCESSOR OVERVIEW FX OPERATION REVERBS DELAYS MODULATED EFFECTS EFFECTS DATA CHART USING YOUR NOTEPAD 124/124FX CONSOLE MARK-UP SHEETS DIMENSIONS APPLICATIONS TYPICAL CONNECTING LEADS TYPICAL SPECIFICATIONS WARRANTY GLOSSARY 38
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of a polarised or grounding type plug. A polarised plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This Class A digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la Classe A respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. 4 Soundcraft Notepad User Guide

For your own safety and to avoid invalidation of the warranty please read this section carefully.

SAFETY SYMBOL GUIDE

For your own safety and to avoid invalidation of the warranty all text marked with these symbols should be read carefully.

WARNINGS

The lightning flash with arrowhead symbol, is intended to alert the user to the presence of un-insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTIONS

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Contain important information and useful tips on the operation of your equipment.
HEADPHONES SAFETY WARNING
Contain important information and useful tips on headphone outputs and monitoring levels.
Recommended Headphone Impedance >= 32 Ohms.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Note: It is recommended that all maintenance and service on the product should be carried out by Soundcraft or its authorised agents. Soundcraft cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorised personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not expose the apparatus to dripping or splashing and do not place objects filled with liquids, such as vases, on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. Batteries (battery pack or batteries installed) should not be exposed to excessive heat such as sunshine, fire or the like. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths, curtains etc. The Soundcraft Notepad mixer must only be connected through the AC power adapter supplied, which must have one of the following part numbers: Notepad AC Adaptor UK Notepad AC Adaptor EU Notepad AC Adaptor US Notepad AC Adaptor JP Notepad AC Adaptor AZ C089.202100 C089.202101 C089.202102 C089.202103 C089.202104
The mains supply disconnect device is the mains plug. It must remain accessible so as to be readily operable when the apparatus is in use.
If any part of the mains cord set is damaged, the complete cord set should be replaced. The following information is for reference only. The wires in the mains lead are coloured in accordance with the following code: Earth (Ground): Green and Yellow (US - Green/Yellow) Neutral: Blue (US - White) Live (Hot): Brown (US - Black) As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol. The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L Ensure that these colour codes are followed carefully in the event of the plug being changed. This unit is capable of operating over a range of mains voltages as marked on power supply unit.

INTRODUCTION

Thank you for purchasing a Soundcraft Notepad mixer. The Notepad range is a compact mixing solution, bringing you all the features and performance that you expect from a Soundcraft product, at an extraordinarily low price. The packaging in which your Notepad arrived forms part of the product and should be retained for future use. Owning a Soundcraft console brings you the expertise and support of one of the industrys leading manufacturers, and the results of over 3 decades of supporting some of the biggest names in the business. Our knowledge has been attained through working in close contact with leading professionals and institutes to bring you products designed to get the best possible results from your mixing. Built to the highest standards using quality components and surface mount technology, the Notepad is designed to be as easy to use as possible. We have spent years researching the most efficient methods of control for two key reasons: 1) Engineers, musicians, writers and programmers all need to have very few interruptions to the creative process; our products have been designed to be almost transparent, allowing this process to breathe. 2) Whether performing or recording, time is a very expensive and rare commodity. Our products have a user interface which is recognised by millions to be the industry standard because of its efficiency. The sonic qualities of our products are exemplary - some of the same circuits which are used on our most expensive consoles used on International tours are employed in the Notepad, bringing you the great Soundcraft quality in a small format console without compromise. You will also be glad to know you have a one year warranty with your product from the date of purchase. The Notepad has been designed using the latest high-end software based engineering packages. Every console from Soundcraft has been proven to stand up to all the stress and rigours of modern day mixing environments. The entire Notepad is manufactured using some of the most advanced techniques in the world, from high density surface mount PCB technology, to computer aided test equipment able to measure signals well outside the range of normal hearing.
ADVICE FOR THOSE WHO PUSH THE BOUNDARIES Although your new console will not output any sound until you feed it signals, it has the capability to produce sounds which when monitored through an amplifier or headphones can damage hearing over time. Please take care when working with your audio - if you are manipulating controls which you dont understand (which we all do when we are learning), make sure your monitors are turned down. Remember that your ears are the most important tool of your trade, look after them, and they will look after you. Most importantly - dont be afraid to experiment to find out how each parameter affects the sound - this will extend your creativity and help you to get the best from your mixer and the most respect from your artists and audience.

Notepad 124FX only 23 FX TO MAIN 24 FX TO MON 25 FX PROCESSOR Notepad 102 and 124 only 26 AUX SEND The rotary control regulates the signal level being fed from the FX processor to the MAIN MIX L and R outputs. The FX TO MON switch routes the post-FX signal to the monitor/headphones outputs. See the information starting on page 24.
The rotary control regulates the signal level being fed from the AUX bus to the AUX OUTPUT socket (and MON output when selected). The AUX TO MON switch routes the AUX signal to the Monitor/Headphone outputs.

27 AUX TO MON

WIRING UP
Mic Input The MIC input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or UNBALANCED low-level signals, whether from delicate vocals requiring the best low-noise performance, or drum kits needing maximum headroom. Professional dynamic, condenser or ribbon mics are best because these will be LOW IMPEDANCE. While you can use low-cost HIGH IMPEDANCE mics, you do not get the same degree of immunity to interference on the microphone cable and as a result the level of background noise may be higher. If you turn the PHANTOM POWER on, the socket provides a suitable powering voltage for professional condenser mics.
DO NOT use UNBALANCED sources with the phantom power switched on. The voltage on pins 2 & 3 of the XLR connector may cause serious damage. BALANCED dynamic mics may normally be used with phantom power switched on (contact your microphone manufacturer for guidance)
The input level is set using the input GAIN knob. The LINE input offers the same gain range as the MIC input, but at a higher input impedance, and is 15dB less sensitive. This is suitable for most line level sources.
WARNING ! Start with the input GAIN knob turned fully anticlockwise when plugging high level sources into the LINE input to avoid overloading the input channel or giving you a very loud surprise!
Line Input Accepts 3-pole 6.35mm (1/4) jacks, or 2-pole mono jacks which will automatically ground the cold input. Use this input for sources other than mics, such as keyboards, drum machines, synths, tape machines or DI boxes. The input is BALANCED for low noise and immunity from interference, but you can use UNBALANCED sources by wiring up the jacks as shown, although you should then keep cable lengths as short as possible to minimise interference pick-up on the cable. Note that the ring must be grounded if the source is unbalanced. Set the input level using the GAIN knob, starting with the knob turned fully anticlockwise. Unplug any MIC connection when using the LINE input. Stereo Inputs 5-6. 7-8, 9-10 and 11-12 (Notepad 124 Stereo inputs 3-4 and 5-6 (Notepad 102) These accept 3-pole 6.35mm (1/4) jacks, or 2-pole mono jacks which will automatically ground the cold input. Use these inputs for sources such as keyboards, drum machines, synths, tape machines or as returns from processing units. The input is BALANCED for low noise and immunity from interference, but you can use UNBALANCED sources by wiring up the jacks as shown, although you should keep cable lengths as short as possible to minimise interference pick-up on the cable, but the ring must be grounded if the source is unbalanced. Mono sources can be fed to both paths by plugging into the Left jack only. 12 Soundcraft Notepad User Guide

Stereo Inputs 7-8, 9-10 (Notepad 102) These accept unbalanced RCA Phono plugs and are optimised for -10dBV operation from line sources such as a CD or MP3 player. They can accept signals from balanced sources by using an appropriate cable, see pages 34/35 for cable wiring details.
Mix Outputs The MIX outputs are on 1/4 TRS jacks, wired as shown, and incorporate balanced line drives, allowing long cable runs to balanced amplifiers and other equipment. Aux/FX SEND Outputs The Aux/FX Bus outputs are on 3-pole 6.35mm (1/4) jack sockets, wired as shown on the left, and are impedance balanced. MONITOR Outputs The MONITOR outputs are on 3-pole 6.35mm (1/4) jack sockets, wired as shown on the left, and are impedance balanced. Headphones The PHONES output is a 3-pole 6.35mm (1/4) jack, wired as a stereo output as shown, ideally for headphones of 32 or greater. 8 headphones are not recommended. We recommend you check out the range of headphones available from AKG, at www.akg.com
Polarity (Phase) You will probably be familiar with the concept of polarity in electrical signals and this is of particular importance to balanced audio signals. Just as a balanced signal is highly effective at cancelling out unwanted interference, so two microphones picking up the same signal can cancel out, or cause serious degradation of the signal if one of the cables has the +ve and -ve wires reversed. This phase reversal can be a real problem when microphones are close together and you should therefore always take care to connect pins correctly when wiring audio cables. Grounding and Shielding For optimum performance use balanced connections where possible and ensure that all signals are referenced to a solid, noise-free earthing point and that all signal cables have their screens connected to ground. In some unusual circumstances, to avoid earth or ground loops ensure that all cable screens and other signal earths are connected to ground only at their source and not at both ends. If the use of unbalanced connections is unavoidable, you can minimise noise by following these wiring guidelines: On INPUTS, unbalance at the source and use a twin screened cable as though it were balanced. On OUTPUTS, connect the signal to the +ve output pin, and the ground of the output device to -ve. If a twin screened cable is used, connect the screen only at the mixer end. Avoid running audio cables or placing audio equipment close to thyristor dimmer units or power cables. Noise immunity is improved significantly by the use of low impedance sources, such as good quality professional microphones or the outputs from most modern audio equipment. Avoid cheaper high impedance microphones, which may suffer from interference over long cable runs, even with well-made cables. Grounding and shielding is still seen as a black art, and the suggestions above are only guidelines. If your system still hums, an earth/ground loop is the most likely cause. Two examples of how an earth loop can occur are shown below.

TAKE CARE when using unbalanced sources, which may be damaged by the phantom power voltage on pins 2 & 3 of the XLR connector. Unplug any mics if you want to use the LINE Input. The input level is set using the GAIN knob. 2 Line Input Accepts 3-pole 6.35mm (1/4) jacks. Use this input for sources other than mics, such as keyboards, drum machines, synths, tape machines or DId guitars. The input is BALANCED for low noise and top quality from professional equipment, but you can use UNBALANCED sources by wiring up the jacks as shown in the wiring up section, although you should then keep cable lengths as short as possible. Unplug anything in the MIC input if you want to use this socket. Set the input level using the GAIN knob. 3 Gain This knob sets how much of the source signal is sent to the rest of the mixer. Too high, and the signal will distort as it overloads the channel. Too low, and the level of any background hiss will be more noticeable and you may not be able to get enough signal level to the output of the mixer. Note that some sound equipment, particularly that intended for domestic use, operates at a lower level (-10dBV) than professional equipment and will therefore need a higher gain setting to give the same output level. 4 Equaliser The Equaliser (EQ) allows fine manipulation of the sound, particularly to improve the sound in live PA applications where the original signal is often far from ideal and where slight boosting or cutting of particular voice frequencies can really make a difference to clarity. There are three sections giving the sort of control usually only found on much larger mixers. The EQ knobs can have a dramatic effect, so use them sparingly and listen carefully as you change any settings so that you get to know how they affect the sound.
HF EQ Turn to the right to boost high (treble) frequencies above 12kHz by up to 15dB, adding crispness to cymbals, vocals and electronic instruments. Turn to the left to cut by up to 15dB, reducing hiss or excessive sibilance which can occur with certain types of microphone. Set the knob in the centre-detented position when not required. MID EQ Turn to the right to boost mid frequencies around 1kHz by up to 15dB This allows some truly creative improvement of the signal in live situations, because this mid band covers the range of most vocals. Set the knob to the centre-detented position when not required. LF EQ Turn to the right to boost low (bass) frequencies below 80Hz by up to 15dB, adding warmth to vocals or extra punch to synths, guitars and drums. Turn to the left to cut low frequencies by up to 15dB for reducing hum, stage rumble or to improve a mushy sound. Set the knob to the centre-detented position when not required. 5 HIGH-PASS FILTER Pressing this switch activates the high-pass filter. This reduces the level of bass frequencies only. Use this in live PA situations to reduce stage rumble or popping from mics. 6 AUX SEND (Notepad 102 and 124) This is used to set up a separate mix for FOLDBACK or MONITORS and is mixed to the respective Aux Output. The send is pre-fade, so the output level will be independent of the CHANNEL LEVEL control setting.

6 FX SEND (Notepad 124FX) This control sets the level of the post-fade signal being sent to the FX bus; from there it is routed to the FX processor. The FX Send is post-fade. 7 PAN This control sets the amount of the channel signal feeding the Left and Right MIX buses, allowing you to move the source smoothly across the stereo image. When the control is turned fully left or right you are able to route the signal at unity gain to either left or right outputs individually. 8 INPUT CHANNEL LEVEL This control allows precise balancing of the various source signals being mixed to the Master Section. You get most control when the input GAIN is set up correctly, giving full travel on the control. 9 PEAK LED This LED will light when the signal level approaches clipping at either of two monitored points: PRE-EQ and POST-EQ.
STEREO INPUT CHANNELS (Notepad 124FX shown)
There are four stereo inputs available.
1 STEREO INPUTS These inputs accept 3-pole 6.35mm (1/4) jacks.* Use these inputs for sources such as keyboards, drum machines, synths, tape machines or processing units. The inputs are BALANCED for low noise and top quality from professional equipment, but you can use UNBALANCED sources by wiring up the jacks as shown in the Wiring Up section earlier in this manual, although you should then keep cable lengths as short as possible. Mono sources may be used by plugging into the left jack only.
2 AUX/FX SEND (FX send shown, Notepad 124FX) This is used to set up a separate mix for FOLDBACK, EFFECTS or RECORDING, and is mixed to the Aux or FX Send Output at the rear of the mixer. For the Notepad 124FX, it is desired that for the signal fades up and down with the fader (this is called POST-FADE), but for Foldback or Monitor feeds using the Notepad 102 and Notepad 124, it is important for the send to be independent of the fader (this is called PRE-FADE). 3 +4/-10 SWITCH (Notepad 124/124FX only) This switch allows you to change the input sensitivity of the stereo input. Most consumer-type equipment such as CD players has an output of -10dBv so this switch setting should be used. For professional equipment which has higher level outputs, the +4 setting should be used. If in doubt, always start with the +4 setting so that you do not overload the input. 4 BAL (BALANCE) This control sets the amount of the channel signal feeding the Left and Right MIX buses, allowing you to balance the source in the stereo image. When the control is turned fully right or left you feed only that side of the signal to the mix. Unity gain is provided by the control in the centre-detented position. 5 INPUT CHANNEL LEVEL This control allows precise balancing of the various source signals being mixed to the Master Section. * The Notepad 102 features a combination of 3-pole jacks and RCA Phono connectors. The jack inputs are optimised for professional +4dBu levels, while the RCA Phono inputs are optimised for -10dBV level equipment such as CD or MP3 players and computer sound cards.

Notepad 102 Stereo Inputs
MASTER SECTION (Notepad 124FX shown)
1 POWER INDICATOR This LED lights to show when power is connected to the console, and the power switch is ON. 2 PHANTOM POWER Many professional condenser mics need PHANTOM POWER, which is a method of sending a powering voltage down the same wires as the mic signal. Press the switch to enable the +48V power to all of the MIC inputs. The adjacent LED illuminates when the power is active. WARNING: TAKE CARE when using unbalanced mics which may be damaged by the phantom power voltage. Balanced dynamic mics can normally be used with phantom power switched on (contact your microphone manufacturer for guidance). Mics should always be plugged in, and all output faders set to minimum before switching the Phantom Power ON to avoid damage to external equipment.

2-TRACK

3 INPUT FROM 2-TRACK These two RCA phono sockets are unbalanced Left and Right line-level inputs, used for connecting a playback device such as a CD player or MP3 player. 4 ROUTE 2-TRACK TO MAIN Press this switch to route the 2 Track input signals to the MIX Left/ Right signals. 5 ROUTE 2-TRACK TO MON Press this switch to route the 2 Track input signals to the MONITORING outputs.

MONITOR OUT

6 MONITOR OUTPUT LEVEL This control sets the signal level fed to the MONITOR LEFT & RIGHT outputs and the Headphone outputs.
7 MONITOR OUTPUTS The Monitor Outputs are on 3-pole 6.35mm (1/4) jacks and are impedance balanced. 8 HEADPHONES SOCKET The PHONES output is a 3-pole 6.35mm (1/4) jack, wired as a stereo output, ideally for headphones of 32 or greater. 8 headphones are not recommended. 9 METERS The three-colour peak reading BARGRAPH METERS normally show the level of the signal(s) selected by the monitor source-select switches, giving you a constant warning of excessive peaks in the signal(s) which might cause overloading. Aim to keep the signal within the amber segments at peak levels for best performance. Similarly, if the output level is too low and hardly registering at all on the meters, the level of background noise may become significant. Take care to set up the input levels for best performance. 10 RECORD OUTPUTS These two RCA outputs carry a copy of the MIX L and MIX R signals. They allow the use of a recording device, e.g. PC, cassette tape recorder, hard-disk recorder etc. 11 AUX (Notepad 124)/FX BUS (Notepad 124FX) OUTPUT This output is on a 3-pole 6.35mm (1/4) jack and is impedance balanced.

MIX OUTPUTS

12 MIX FADER The MIX FADER sets the final level of the Mix outputs. This should normally be set close to the 0 mark if the input GAIN settings have been correctly set, to give maximum travel on the fader for smoothest control. 13 MIX OUTPUTS The Mix LEFT and RIGHT outputs are sent from the 1/4 jack sockets as balanced signals.
FX PROCESSOR - NOTEPAD 124FX Only
For detailed instructions on using the FX Processor see the section which starts on the next page. 14 FX TO MAIN This control regulates the signal level being fed from the FX processor to the MAIN mix L and R outputs.
FX PROCESSOR OVERVIEW (NOTEPAD 124FX ONLY)
The effects within the console have been designed with both live sound reinforcement and home recording in mind. The effects processor offers increased versatility and high quality effects, all instantly accessible via the extremely intuitive front panel controls. The effects processor has more than 100 programs. 1. Digital Effect Display This 2-digital numeric display shows the program number that is currently applied. Rotating the Program control will scroll through different program numbers, pressing the PROGRAM control (3) will select the effect. The display will revert back to the original program if a new program is not selected within fifteen seconds. For a list of available effects, please refer to the Effects Data Chart Table.
2. Sig and Clip Indicators The Sig LED will light up when signal is sent to the effects processor, and the Clip LED will light up shortly before excessive signals are dynamically clipped. If the Clip LED lights up too often, to turn down one or all FX sends on input channels. 3. Program Control This control is used to scroll through the various effects. Pushing this control will apply the new effect. Tap Delay (selections A0 to A8) When a tap-delay effect is selected, pressing this control will allow users to select the tap-delay time. By pushing the button several times, the effects processor interprets the time between last two pushes and remembers this as the delay time, until the button is pushed again (this is kept, even after the power is turned off). When the tap delay effect is selected, a small LED will flash within the display window to mark the tempo. 4. EFX to Main Control This will adjust the level of the FX signal that will be sent to the Main Mix left and right outputs. 5. EFX to MON Button This button is pushed to allow the signal from the Digital Effect processor to be sent to the Monitoring outputs for monitoring purposes.

music, mellowing and thickening the initial sound. Plate reverbs are often used to enhance popular music, particularly percussion. Reverse Reverb Reverse reverb works in the opposite fashion from normal reverb. Whereas a normal reverb has the loudest series of reflections heard first that then become quieter over time, the Reverse reverb has the softest reflections (essentially the tail of the reverb) heard first, and then grows louder over time until they abruptly cut off. Gated Reverb Gated reverb is created by feeding a reverb, such as a metal plate, through a gate device. The Gated reverb provides a fairly constant sound with no decay until the reverb is cut off abruptly. This program works well on percussion particularly on snare and toms; be sure to experiment with other sound sources as well.

DELAYS

Delays repeat a sound a short time after it first occurs. Delay becomes echo when the output is fed back into the input (feedback). This turns a single repeat into a series of repeats, each a little softer than the last. Ping-Pong Delay This delay effect pans the delay repeats from left to right, while the input signal remains at its original (center) position.

MODULATED EFFECTS

Chorus Chorus creates a lush, full sound by combining two or more signals together where one is unaffected and the other signals vary in pitch very slightly over time. Chorus is commonly used to fatten up tracks and to add body to guitars without coloring the original tone. Chorus can also be used with discretion to thicken a vocal track. Flanger This effect was originally created by simultaneously recording and playing back two identical programs on two tape recorders, then using hand pressure against the flange of the tape reels to slow down first one machine, then the other. The result was a series of changing phase cancellations and reinforcements, with characteristic swishing, tunneling, and fading sounds. Phaser The Phaser automatically moves frequency notches up and down the spectrum of the signal by means of a low frequency oscillator (LFO), creating an oscillating comb-filter type effect. This effect is very userful on keyboards (especially pad presets) and guitars. Tremelo Tremolo creates rhythmic changes in signal amplitude. Tremolo affects both channels amplitude simultaneously.

EFFECTS DATA CHART

NO PROGRAM NAME ROOM COMPACT ROOM 1 COMPACT ROOM 2 SMALL ROOM 1 SMALL ROOM 2 MID ROOM 1 MID ROOM 2 BIG ROOM 1 TUNNEL HALL JAZZ CLUB SMALL HALL 1 SMALL HALL 2 SPRING HALL MID HALL 1 MID HALL 2 RECITAL HALL BIG HALL 2 PLATE SMALL PLATE TAIL PLATE MID PLATE 1 MID PLATE 2 REVERSE PLATE LONG PLATE 1 LONG PLATE 2 LONG PLATE 3 DELAY-1(stereo) SHORT DELAY 1 SHORT DELAY 2 PING PONG DELAY MID DELAY 1 MID DELAY 1 SHORT DELAY 1 (MONO) MID DELAY 1 (MONO) LONG DELAY 1 (MONO) CHORUS SOFT CHORUS SOFT CHORUS 2 SOFT CHORUS 3 WARM CHORUS WARMER CHORUS 1 WARMER CHORUS 2 WARMER CHORUS 3 HEAVY CHORUS FLANGER CLASSIC FLANGER 1 CLASSIC FLANGER 2 GENTLE FLANGER WARM FLANGER MODERN FLANGER 1 MODERN FLANGER 2 DEEP FLANGER 1 DEEP FLANGER 2 PHASER CLASSIC PHASER 1 CLASSIC PHASER 2 COOL PHASER WARM PHASER HEAVY PHASER 1 HEAVY PHASER 2 WILD PHASER 1 WILD PHASER 2 REV-TIME 0.05 0.4 0.45 0.6 0.1.2 3.85 REV-TIME 0.9 1.5 1.75 1.9 2.3 2.45 2.7 3.3 REV-TIME 0.9 1.2 1.3 2.2 2.25 2.4.2 DELAY AVERG. 0.07 0.14 0.11 0.15 0.3 0.06 0.13 0.18 LFO 0.2 0.5 0.8 1.8 3.2 5.2 7.8 9.6 LFO 0.1 0.3 0.6 1.2.8 4.LFO 0.1 0.4 1.4 3.6 7.4 9.6 PARAMETER SETTING EARLY LEVEL EARLY LEVEL HPF R-LEVEL DEPTH DEPTH DELAY 3.6 2.6 0.7 0.3 1.2 2.8 0.8 4.8 NO A0 A1 A2 A3 A4 A5 A6 A7 A8 T0 T1 T2 PN PROGRAM NAME SLOW PAN SLOW PAN 1 SLOW PAN 2 MID SHIFT MID SHIFT 1 MID SHIFT 2 MID SHIFT 3 FAST MOVE TREMOLO LAZY TREMOLO VINTAGE TREMOLO WARM TREMOLO WARM TREMOLO 1 HOT TREMOLO HOT TREMOLO 1 CRAZY TREMOLO 1 CRAZY TREMOLO 2 DELAY+REV DELAY+REV 1 DELAY+REV 2 DELAY+REV 3 DELAY+REV 4 DELAY+REV 5 DELAY+REV 6 DELAY+REV 7 DELAY+REV 8 CHORUS+REV CHORUS+REV 1 CHORUS+REV 2 CHORUS+REV 3 CHORUS+REV 4 CHORUS+REV 5 CHORUS+REV 6 CHORUS+REV 7 CHORUS+REV 8 FLANGER+REV FLANGER+REV 1 FLANGER+REV 2 FLANGER+REV 3 FLANGER+REV 4 FLANGER+REV 5 FLANGER+REV 6 FLANGER+REV 7 FLANGER+REV 8 GATED-REV GATED-REV-GATED-REV-GATED-REV-GATED-REV-TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TAP DELAY TEST TONE LOW FREQUENCY MID FREQUENCY HIGH FREQUENCY PINK NOISE SPEED 0.1 0.1 0.4 0.8 1.2 1.8 1.8 3.4 SPEED 0.8 1.5 2.8 4.6 6.8 9.20 REV REV REV RELEASE 0.02 0.2 0.02 0.5 FB LEVEL 80 FREQUENCY 100Hz 1kHz 10kHz 20Hz~20kHz PARAMETER SETTING PAN TYPE R-->L R<-->L R-->L R<-->L L-->R L-->R R-->L R<-->L MODE-TYPE TRG TRG TRG TRG TRG TRG TRG TRG DELAY-8 CHORUS FLANGER REV TAIL PLATE TAIL PLATE REVERSE PLATE REVERSE PLATE RANGE 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S 100mS - 2.7S SHAPE SINEWAVE SINEWAVE SINEWAVE

Note: The initial settings should only be regarded as a starting point for your mix. It is important to remember that many factors affect the sound during a live performance, for instance the size of the audience! You are now ready to start building the mix and this should be done progressively, listening carefully for each component in the mix and watching the meters for any hint of overload. If this occurs, back off the appropriate Channel Fader slightly until the level is out of the red segments, or adjust the Master Faders. Remember that the mixer is a mixer, not an amplifier. Increasing the overall level is the job of the amplifier, and if it is impossible to provide adequate level, it is probable that the amplifier is too small for the application. Choose your amplifier carefully, and do not try to compensate for lack of power by using the mixer to increase output level. Note: The level of any source signal in the final output is affected by many factors, principally the Input Gain control, Channel Fader and Mix Faders. You should try to use only as much microphone gain as required to achieve a good balance between signals, with the faders set as described above. If the input gain is set too high, the channel fader will need to be pulled down too far in compensation to leave enough travel for successful mixing and there is a greater risk of feedback because small fader movements will have a very significant effect on output level. Also there will be a chance of distortion as the signal overloads the channel and causes clipping. If the gain is set too low, you will not find enough gain on the faders to bring the signal up to an adequate level, and backgound hiss will be more noticeable. This is illustrated below:
MARK-UP SHEETS Notepad 124FX
You may freely copy these pages, and use them to record the settings used for particular applications/gigs.
MARK-UP SHEETS Notepad 124
MARK-UP SHEETS Notepad 102
DIMENSIONS (Notepad 124 and 124FX)

242mm/9.53

220mm 8.66

45mm 1.77

37mm 1.46

220mm/8.66

DIMENSIONS (Notepad 102)

215mm/8.5

APPLICATIONS
APPLICATION EXAMPLE - LIVE SOUND REINFORCEMENT Using Notepad 124 model

TYPICAL CONNECTING LEADS

NOTEPAD SERIES TYPICAL SPECIFICATIONS
Frequency Response Mic / Line Input to any Output..+1/-1.5dB, 20Hz 20kHz T.H.D. Mic Sensitivity -30dBu, +10dBu @ Mix output, 22Hz-22kHz..< 0.005% @ 1kHz Noise Mic Input E.I.N. (maximum gain)..-128.5dBm (150 source) Aux, Mix and Masters (@ 0dB, at unity)..< -85dBu Crosstalk (@ 1kHz) Channel Faders cut...> 87dB Master Faders cut...>100dB CMRR @1kHz....>90dB EQ High Pass Filter..100Hz @ 12db/Octave HF...12kHz, +/-15dB MF....1kHz, +/-15dB LF....80Hz, +/-15dB Q....0.7 Power Consumption...Less than 40W Operating Conditions Temperature Range...5C to 40C Input & Output Levels Mic Input...+10dBu max Line Input...+22dBu max Stereo Input...+20dBu max Mix Output...+25dBu max Headphones (@32)...300mW Input & Output Impedances Mic Input....2k Line Input....18k Stereo Input...20k Outputs....150 E & OE. Soundcraft reserves the right to change specifications without notice. July2009

WARRANTY

1 2 Soundcraft is a trading division of Harman International Industries Ltd. End User means the person who first puts the equipment into regular operation. Dealer means the person other than Soundcraft (if any) from whom the End User purchased the Equipment, provided such a person is authorised for this purpose by Soundcraft or its accredited Distributor. Equipment means the equipment supplied with this manual. If within the period of twelve months from the date of delivery of the Equipment to the End User it shall prove defective by reason only of faulty materials and/or workmanship to such an extent that the effectiveness and/or usability thereof is materially affected the Equipment or the defective component should be returned to the Dealer or to Soundcraft and subject to the following conditions the Dealer or Soundcraft will repair or replace the defective components. Any components replaced will become the property of Soundcraft. Any Equipment or component returned will be at the risk of the End User whilst in transit (both to and from the Dealer or Soundcraft) and postage must be prepaid. This warranty shall only be valid if: a) the Equipment has been properly installed in accordance with instructions contained in Soundcrafts manual; and b) the End User has notified Soundcraft or the Dealer within 14 days of the defect appearing; and c) no persons other than authorised representatives of Soundcraft or the Dealer have effected any replacement of parts maintenance adjustments or repairs to the Equipment; and d) the End User has used the Equipment only for such purposes as Soundcraft recommends, with only such operating supplies as meet Soundcrafts specifications and otherwise in all respects in accordance with Soundcrafts recommendations. Defects arising as a result of the following are not covered by this Warranty: faulty or negligent handling, chemical or electro-chemical or electrical influences, accidental damage, Acts of God, neglect, deficiency in electrical power, air-conditioning or humidity control. The benefit of this Warranty may not be assigned by the End User. End Users who are consumers should note their rights under this Warranty are in addition to and do not affect any other rights to which they may be entitled against the seller of the Equipment.

GLOSSARY

AFL After-fade listen: a function that allows the operator to monitor the post-fade signal in a channel independently of the main mix. Auxiliary send An output from the console comprising a mix of signals from channels derived independently of the main stereo mix. Balance The relative levels of the left and right channels of a stereo signal. Balanced A method of audio connection which balances the signal between two wires, these wires also have a screen which carries no signal. Any interference is picked up equally by the two wires, which results in cancellation of the unwanted signal. In this guide, the term can refer to various circuit architectures. Connection details are given in relevant sections. Clipping The onset of severe distortion in the signal path, usually caused by the peak signal voltage being limited by the circuits power supply voltage. DAT Digital Audio Tape, a cassette-based digital recording format. dB (decibel) A ratio of two voltages or signal levels, expressed by the equation dB=20Log10 (V1/ V2). Adding the suffix u denotes the ratio is relative to 0.775V RMS. DI(direct injection) The practice of connecting an electric musical instrument directly to the input of the DI Box mixing console, rather than to an amplifier and loudspeaker which is covered by a microphone feeding the console. Equaliser A device that allows the boosting or cutting of selected bands of frequencies in the signal path. Fader A linear control providing level adjustment. Feedback The `howling sound caused by bringing a microphone too close to a loudspeaker driven from its amplified signal. Foldback A feed sent back to the artistes via loudspeakers or headphones to enable them to monitor the sounds they are producing. Frequency response The variation in gain of a device with frequency. Gain The amount of amplification in level of the signal. Headroom The available signal range above the nominal level before clipping occurs. Impedance balancing A technique used on unbalanced outputs to minimise the effect of hum and interference when connecting to external balanced inputs. Insert A break point in the signal path to allow the connection of external devices, for instance signal processors or other mixers at line level signals. Nominal levels can be anywhere between 0dBu to +6dBu, usually coming from a low impedance source. Pan (pot) Abbreviation of panorama: controls the levels sent to left and right outputs. Peaking The point at which a signal rises to its maximum instantaneous level, before falling back down again. It can also describe an equaliser response curve affecting only a band of frequencies, (like on a graphic equaliser), peaking at the centre of that band. Peak LED A visual indication of the signal peaking just before the onset of clipping, which will distort the signal. PFL Pre-fade listen: a function that allows the operator to monitor the pre-fade signal in a channel independently of the main mix. Phase A term used to describe the relationship of two audio signals. In-phase signals reinforce each other, out-of-phase signals result in cancellation. Phase is a measurement of relative displacement between two waves of identical frequency. Polarity A term used to describe the orientation of the positive and negative poles of an audio connection. Normally connections are made with positive to positive, negative to negative. If this is reversed, the result will be out-of-phase signals (see phase above). Post-fade The point in the signal path after a fader and therefore affected by the fader position. 42 Soundcraft Notepad User Guide