USB 2.0 Bus powered Cable With poly-fuse limited current output USB cable to device head: USB B/M or USB Mini B/M USB Signal Black USB Cable
Standard USB to 2 or 4 RS-232 Adapter PDA RS-232 Port support USB 1.1 & USB 2.0 compatible
USB to RS-232 Serial Converter

Feature :

Full compliance with the USB Specification 1.1 Supports all common RS232 Serial port Over 230Kbps transfer rate per port Supports remote wake-up and power management Compatible Mac Windows98 / SE / ME / 2000 / XP / OS 8.6 / OS-9 / OS-X
USB to RS-422 & RS-485 Converter ( For DB-9 Male & RJ-11 Jack )
The USB converter is housed in a strong molded enclosure designed for use in rugged application areas. USB adds a Windows serial Com port via its USB connection and can be configured to work with RS-422 and RS-485 peripherals such as POS and Industrial Control devices. USB Plug and Play allows easy serial port expansion and requires no IRQ, DMA, or I/O port resources. It Supports data transfer rates of up to 1 million bps. No external power supply is required as USB converter takes its power form the USB Bus.
Full compliance with the USB Specification 1.1 Over 1Mbps transfer rate per port Compatible Windows98/SE/ME/2000/XP.Mac OS8.6/OS-9/OS-X

UTS-485

USB to RS-485 & DB-9 Male

UTS-422

USB to RS-422 & DB-9 Male

UMC-201

USB A type Male to DB9 Pin Male (Chip:FTDI)

UTS-200J

USB to RS-422/RS-485 & RJ44 Female

UMC-211

USB A type Male to DB9 Pin Male (Chip:PROLIFIC)

UTS-200J2

USB to RS-422 & RJ-11 Female

UTS-200J5

USB to RJ-485 & RJ-11 Female
USB to Multi - RS-232 / RS - 422 / RS - 485 Converter
The USB 2 or 4 port RS-232 Converter, is a low-cost, highperformance device. It operates as a bridge and provides single and easy connection between on USB port and two or four-serial ports. Each serial port can be independently configured into various synchronous and asynchronous interfaces. Uses can have the option to operate multiple devices at the same time. This products is designed to accommodate those peripherals with serial-port, like cellular phone, digital camera, modem, mouse, PDA, GPS, ISDN terminal adapter, etc.

USB to PS/2 Converter

USB Combo Converter
Supports external IrDA V.1.2 compliant PHY Supports SIR and FIR from 115Kps to 4Mbps data transfer rate Memory mapped IrDA buffer for dynamic buffer management DMA data transfer scheme between IrDA Tx/Rx buffer and Usb Rx/Tx buffer to achieve the best data transfer throughput Supports Palm M100 IR com Supports peripherals with IrDA device, lick cellular phone/PDA/Printer/Digital camera, etc. Transmission distanceG1CM-100CM (3 feet) Compliant with the asynchronous serial interfaces

UPS-102

USB to PS2 K/B & Mouse Convert

GMUPS-23

Support tow PS/2 Devices (Keyboard and Mouse) and converts to the USB Interface. Convert the PC PS2 of KVM switch to USB Port (PC. MAC.Linux or SUN Platforms). Support standard PS/2 Mouse, Microsoft IntelliMouse. Easy to Install, no software driver needed No power adapter is needed Comply to USB 1.0 and 1.1 Specification Support UHCI an OHCI USB Interface

UPR-202

USB to PS2 Keyboard/Mice & RS-232

USA-201

USB to IrDA & RS-232

USB Audio Converter

The USB 5.1 Channel Audio Adapter that provides an amazing audio accessory for any computer with a USB port. It is quipped with standard input and output connectors to add a great stereo input and output performance. The USB 5.1 Channel Audio Adapter not only combines high quality audio recording and playback capabilities but also allows the connection of most popular audio gear such as microphones,home stereos,musical instruments, and powered speakers to your USB capable computer.
USB 2.0 to Ethernet Converter
The USB 2.0 to Fast Ethernet Adapter is a high performance and highly integrated USB2.0 bus Ethernet Controller with embedded 7K*16 bit SRAM. The Adapter supports both 10 Mbps and 100 Mbps Ethernet function based on IEEE802.3/IEEE802.3u LAN standard
Compatible with IEEE 802.3u 100BASE-T, TX Data Transfer rate USB to Ethernet 10/100Mpbs, USB to USB-480/12/ 1.5Mpbps Supports automatic loading of Ethernet ID, USB Descriptor and Converter configuration Supports suspended mode and remote wakeup

UH-125

Aluminum 4 Port HUB Size: 100 x 25 x 18 mm / 38gw Case Material: Aluminum

UH-165

Double Tube Model Size: 95 x 55 x 25 mm / 70gw Case Material: Aluminum with internal metal chassis for optimized heat dissipation

UH-225

Cola Type 3 Ports HUB Size: 60 (In Dia) x 32 mm / 40gw Case Material: Aluminum

UH-335

Mini 4 Ports HUB Size: 60 x 48 x 15 mm / 28gw Case Material: ABS + PC Plastic

UH-175

Mirror Finished Style Size: 105 x 25 x 15 mm / 40gw Case Material: Mirror Finished + Rubber Coating

HU-295

Slim 4 Port HUB Size: 38 x 82 x 10 mm / 30gw Case Material: Metal meshed

UH-515

4 Ports HUB Size: 55 x 100 x 22 mm / 60gw Case Material: ABS Plastic

UH-105

Aluminum 4 Ports HUB Size: 53 x 92 x 20 mm / 60gw Case Material: Aluminum

UH-305

Slim Round Shape Size: 63 (In Dia) x 12 mm / 32gw Case Material: Metal meshed

GU2H-08

Bulit-in Cable 4 Ports HUB Size: 90 x 20 x 15 mm Case Material: ABS Plastic Without power
USB 2.0 / 1.1 Docking Station Series
USB 2.0 /1.1 Docking Station Series

MD-200 MD-100

USB 1.port HUB & RS232 + IEEE1284 + 1.8M Cable + Disk MD-100 USB 2.PORTS HUB+SERIAL + PARALLEL + 1.8M CABLE

MD-1000

USB 2.PORT HUB+PARALLEL+SERIAL+PS2+1M CABLE+CD+SWITCHING POWER ADAPTOR

MD-3000

USB 2.PORT HUB+ETHERNET+PARALLEL+SERIAL+ PS2+1M CABLE+CD+SWITCHING POWER ADAPTOR

MD-6000

USB 2.PORT HUB+ETHERNET+PARALLEL+SERI AL+PS2+IRDA+1M CABLE+CD+SWITCHING POWER ADAPTOR

MD-M20

USB 2.PORT HUB+PARALLEL+SERIAL+PS2+ET HERNET+1.8M CABLE+CD+SWITCHING POWER ADAPTOR

MD-M20A

USB 2.PORT HUB+ETHERNET+PARALLEL+SERI AL+PS2+AUDIO CONVERTER+1.8M CABLE+CD+SWITCHING POWER ADAPTOR

MD-M20CR

SB 2.PORT HUB+ETHERNET+PARALLEL+SERI AL+PS2+7 IN 1 CARD READER+1.8 M CABLE+CD+SWITCHING POWER ADAPTOR

Bluetooth Products

Bluetooth Stereo solutions

MiA02 MZH02

Bluetooth Mobile Multifunction Headphone
Blutetooth Classic Multifunction Headphone
Bluetooth Mini Audio Transmitter for iPod
Bluetooth Portable Audio Transmitter

Features: Provide wireless printing solution to PCs, PDAs and mobile phones Compliant with Bluetooth v.1.1 Support HCRP, BIP, OPP and SPP profiles Class 1 output power Additional USB port for printer sharing with 2nd PC. Powered by AC/DC power adapter
Features: Support both wireless stereo headphone and hands-free headset applications Compliant with Bluetooth v1.1 Support A2DP, Hands-free and Headset profiles Class 2-output power 6 hours of operation time and 20 hours of standby time Powered by two AAA Batteries
Features: A miniature audio transmitter to iPod for wireless steaming audio applications Support remote control features to iPod (volume, play, pause, net, back) Compliant with Bluetooth v1.2 Support A2DP, AVRCP profile Class 2-output power 6 hours of operation time and 20 hours of standby time Powered by Li-Polymer rechargeable battery
Features: A portable audio transmitter to any audio source with standard audio jack Compliant with Bluetooth v1.2 Support AFH for better immunity of interference from WiFi Support A2DP profile Class 2-output power 6 hours of operation time and 25 hours of standby time Powered by Li-Polymer rechargeable battery

BT460 BT470 BT460 BT470

Bluetooth Hi-Fi Audio Station Kit

Transceiver

Receiver Mini Amplifier
1. BT460 Transceiver 2. BT460 Receiver 3. BT470 Mini Amplifier 4. Power adapter (for Transceiver/Receiver) 5. Power adapter (for Mini Amplifier) 6. Aluminum cradle (for Transceiver /Receiver) 7. RCA cable (RCA male to RCA male) 8. RCA Hi-Fi Jack cable (3.5mm stereo jack male to RCA male) 9. RCA Hi-Fi Plug cable (RCA male to 3.5mm stereo jack female) 10. RCA speaker cable(RCA male to speaker bare wire) 11. Speaker wire (bare wire)
Home Theater Application (For Rear Speakers)
The input signal of Hi-PHONO BT460 Transceiver MUST be connected to surround singal output Of 5ch play system. Highly recommend to use in DVD movie. Dont adjust the sound field/effect to 5.1 surround simulation when playing CD, VCD or watching TV to avoid the singal lag in the rear speakers.
Features: Supports Advanced Audio Distribution Profile(A2DP) of Bluetoth specification Up to 50 meters (150 feet) wireless working distance(Bluetooth Class 1 device) Bluetooth one-button pairing operation Wireless stereo transmission for diverse Hi-Fi entertainment systems Ideal audio cable replacement for the 2 rear speakers of the Hi-Fi surround system (2 Audio channels) Plug-n-play with various audio connectors External high gained antenna Stylish aluminum-finished faceplates Aluminum cradle for the vertical placement of BT460 audio station -Extra mini amplifier for emphasizing the wireless audio signals

Wired Internet Camera 350K Pixel SoHo 11Mbps Wireless Internet Camera 350K Pixel

RP-WV200

11Mbps Wireless Internet Camera 350K Pixel

RP-VP230

SoHo Wired Internet Camera 350K Pixel

RP-WV500

MPEG4 Wireless Internet Day / Night Camera

RP-VP500

MPEG4 Internet Day / Night Camera
Simple to use just plug and view the image from the Internet Camera with a valid IP address Supports web configuration with password protection Allows remote access from web browser for live image viewing Supports TCP/IP networking, SMTP e-mail, HTTP and other Internet related protocols Utilized in a mixed operating system environment such as Windows and MAC Powerful IPView application software for image capture and video recording
High Quality MPEG4 Compression RS-485 port for PAN/TILT control (RP-WV500) Built-in web server, view from any web browser. Powerful IPView SP application software for image capture and video recording Supporting 10/100TX Ethernet / Fast Ethernet (RP-VP500) Supporting 10/100TX Ethernet / Fast Ethernet and 54Mbps IEEE802.11g (RP-VP500)
Support ActiveX mode for Internet Explorer and Java mode for Internet Explorer and Netscape Navigator. Supports web configuration with password protection Allows remote access from web browser for live image viewing Provide Static IP and Dynamic IP (DHCP client). Simple to use just plug and view the image from the Internet Camera with a valid IP address Connection to external devices for alarm based events when trigger is activated

Ethernet print server

RP-UB1808
USB 10/100Mbps Ethernet Print Server, 3-P

RP-UB1801A

1-P USB 10/100Mbps Ethernet Print Server, 1-P

RP-1808-A

10/100Mbps Fast Ethernet Print Server, 1P

RP-1807-A

10/100Mbps Fast Ethernet Print Server, 3P
Two SUB 1 1-compliant port. Each port supports 1.5/12Mbps data transmission rate and detects the model of the USB printer automatically. One DB25 parallel port, supports bi-directional communication. One 10/100Mbps N-Way UTP port, supports auto crossover.
One USB 1.1-compliant port. Supports 1.5/12Mbps data transmission rate and detects the model of the USB printer automatically. One 10/100Mbps N-Way UTP port, supports auto crossover. Management support, Web browser and Windows-based
One (RP-1808-A) or Three (RP-1807-A) parallel standard centronics port One RJ-45 10Base-T/100Base-TX port Support multi-port and multi-protocol Build-In CPU to offload intranet servers Build-In EEPROM for software up gradable

Ethernet Switch & Adapter
16/24 Port Gigabit + 2 SFP Optical Web Smart Switch
Supports port-Base QoS, configure through Web browser Port mirroring copies traffic from a specific port to a target port. 48Gbps forwarding bandwidth for switch, nonblocking switch fabric. Support VLAN for performance & security Port Trunk for Bandwidth Aggregation Trap Event : use SNMP Trap mechanism to inform supervisor to know the instant abnormal status of the switch.

RP-G1602W

16-P Gigabit + 2 SFP Optical Web Smart Switch

RP-G2402W

24-P Gigabit + 2 SFP Optical Web Smart Switch
16/24 Port Nway + Fiber Optional Management Switch

RP-1601I

16-P Nway + 1-P Fiber Optional Management Switch

RP-2402I

24-P Nway + 2-P Fiber Optional Management Switch
16* RJ45 ports, with 10/100Mbps, Full/Half duplex auto-negotiation and Auto-MDIX function One module slot for one more 100BaseFX connection (Port 17) Support out-band console and in-band SNMP/Http/Telnet management interface
24* RJ45 ports, with 10/100Mbps, Full/Half duplex auto-negotiation and Auto-MDIX function One module slot for one or two more 100BaseFX connection (Port 25/26) Support out-band console and in-band SNMP/Http/Telnet management interface

PCMCIA Ethernet

FT128MX
ISDN TA + Fast Ethernet 16bit PC Card (Attached Port)

Features : RP-1632DRC

Dangeless Fast Ethernet CardBus Adapter
Key Features: An IBM compatible notebook computer with 386SX or higher processor At least one Type II PC Card socket PCMCIA released 2.1 compliant Card Services and Socket Services
32-bit Data Transfers with Bus-Mastering Maximum 33MHZ Operation Hot Swapping Universal Compatibility and Easy Configuration Auto-Negotiation Function 3.3V power demand
32-bit bus-mastering data transfer. 68-pin connector to PC's CardBus Type II slot 10/100/1000Mbps auto-negotiation operation Built-in Transmit 8K/Receive 64K Bytes RAM Data Buffers Supports Full-duplex mode doubles network data rate to 20/200/2000Mbps Single shielded RJ-45 connector

TA128 ISDN TA PC Card

Key Features: Up to 128K bps data speed Compatible with universal IDSN protocols. D-channel: DSS1 (Euro-ISDN), NI-1, INS-Net 64. B-channel: X.75, V.120, V.110, PPP and Multilink PPP, etc. G3 faxing, soft-modem simulation and ISDN Telephony (available over ISDN CAPI software) supported

RP-3200P

10/100/1000 Mbps Gigabit Ethernet Dangle-less CardBus Adapter

Gigabit Ethernet Adapter

RP-3000M RP-3000AM
1000SX 64 bit Gigabit Ethernet PCI Bus Adapter GiGaBit 1000T PCI adapter 64bit

RP-3200R

RP-3200R/W
Gigabit Ethernet Adapter, w/Boot rom & ACPI socket
IIEEE 802.3 10BASE-T, 802.3u 100BASE-TX and 802.3ab 1000BASE-T compliant Support 64-bit PCI Local Bus Master high-speed operation of Rev.2.2 specification Plug-and-Play installation -- simply insert the card into a PC and it will automatically be configured by the PC BIOS One RJ-45 connector: Auto detection of 10Mbps Ethernet, 100Mbps Fast Ethernet and 1000Mbps Gigabit Ethernet & Auto MDI-X Supports Full-duplex mode doubles network data rate to 20/200/2000Mbps Supports PCI 2.2 Wake-on-LAN for remote wake up 128kb RAM on-chip buffer

Surface Mount Box: Comtemporary style, compact and easy to install. 3 level holes for cable size adjustment. UL listed.
TW-1S Available in 6 brilliant colors for cable TW-2S color coding identification. Designed for ANSI X3T9.5 100Mbps TPPMD, 4/16 Token Ring, Ethernet 10 BaseT applications. Convenient 1000 ft. / Per Spool.
WM-11 WM-04 WM-10 WM-01 (front)
Wallmount box (screw type) single module face plate (screw type) dual module face plate (screw type) 2 ports surface mount box
(Keystone & Insert jacks are not included)

Category 5 Keystone Jack

FOR RJ 45 8p8c UTP IDC Terminal with cap T 568A (CTR-KY) Two-pieces snap-on type metal enclosure provides 100% shielding. CATType 90 degree keystone jack. UL verified Category 5 - meets EIA/TIA TSB-40A specification.
WM-01 WM-02 WM-03 WM-04 WM-10 WM-11

1 port surface mount box

4 ports surface mount box

CTR-KY

Flush Mount Face Plate (For Keystone Jack Insert): Comtemporary style. UL listed.

Category 5 Patch Panel

PP-24 (24 Ports) PP-48 (48 Ports) PP-96 (96 Ports) Designed for up to 100 MHz applications, e.g. ANSI X3T9.Mbps TPPMD, 4/16 Mbps Token Ring and Ethernet 10 Base-T applications. Silkscreened port and pin numbers and paper label for easy & efficient installation. Equipped with locking wire saddle for simple cable arrangement.
UTP CAT 5 patch panel UTP CAT 5 patch panel UTP CAT 5 patch panel
WM-05 WM-06 WM-07 WM-08 WM-09
1 module single gang face plate 2 module single gang face plate 3 module single gang face plate 4 module single gang face plate 6 module single gang face plate
Terminal block connectors, metal front panel. Meets EIA/TIA 568A Cat 5 Standards. T568B or 10 BASE T pin/pair assignment. Super compact design saves space. PCB design for maximum reliability. UL listed & Category 5 Certified.
SNAP-IN MODULES: Easy to install as 1-2-3. Comply with NEC Article 800. Meet FCC Part68, & UL listed.
Modular T Adapter & Coupler
SIM-01 SIM-02 SIM-03 SIM-04 SIM-05

8P8C-T 8P8C-CP

Insert Module for Blank Insert Module w/BNC bulkhead Insert Module w/CATV bulkhead Insert Module w/Fiber ST bulkhead Insert Module w/Fiber SC bulkhead Insert Module w/Mini Din 4 bulkhead Insert Module w/RCA bulkhead

Network Tool Kits & Tester

Network Tool Kits

DL-110K
AS-3501:Utp/Stp Stripper AS-4682:Ratchet Crimping Tool For 6P/8P Plugs Dl-110:Punchdown Tool For 110 Type Terminal Blocks Dl-501:Cable Cutter Plugs: 8P8C*30PCS + 6P6C*30PCS

DL-110K1

AS-3501: UTP/STP Stripper AS-4682: Ratchet Crimping Tool for 6P/8P Plugs. DL-110: Punch Down Tool for 110 Type Terminal Blocks DL-501: Cable Cutter UTP1: Cable Tester: Tests RJ-45EIA, 568A/568B(AT&T 258A), 10 Base-T, Token Ring, RJ11 / 12 USOC and Coaxial BNC Cables

DL-4681K

AS-4681: Crimp Tool for 6P/8P Plugs. AS-3501: UTP/STP Stripper DL-501: Cable Cutter Plugs: 8P8C*50Pcs + 6P6C*50Pcs

DL-110K2

AS-4682: Crimping Tool For 6P/8P Plugs AS-3501: Stripper For UTP/STP Cables DL-501: Cable Cutter DL-110: Punch down Tool For 110 Types FZ373M+N: LAN Cable Tester

DL-702A

Fiber Optic Stripper Strip 125 micron glass fiber with 250 micron buffer coating without scratching on nicking glass fiber. Middle Carbon Steel with Hardened & Black Oxide Finished

STRIPPER

HT-318 DL-1068
Modular Crimps,Strips & Cuts Tool 8P8C/RJ45, 6P6C / RJ12, 6P4C / RJ11 & 6P2C PLUGS Low Carbon Steel with Hardened & Black Oxide Finished

DL-2068

Professinal Modular Crimps,Strips & Cuts Tool 8P8C, 6P6C, 6P4C & 6P2C PLUGS (DR-2068R W/Ratchet Mechanism) Straight Motion & Precise Crimping
Easy stripper for UTP / STP Telecom Wire For stripping wire diameter about 50-60mm, top end for 110 / 88 type insertion use

PUNCH DOWN TOOL

HT-3140 DL-501B DL-110
Impact punch down tool frame with 88/110-type blade Lan Cable Stripper Sharp SK-2 blade for cutter and stripper can be replaced Cable stripper for LAN (UTP/STP), COAX.,flat cables with cutter Impact and punch down tool (Incl. Blades) For seating wire into terminal block or cut off wire end after terminated. Impact tool w / pressure sdjusting control + Blades for 66 type and 110/88 type

Network Cable Tester

LCS-400
TERM4004 Set:4Remote Module (ID1-4) TERM4008 Set: 8 Remote Module(ID1-8) TERM40016 Set: 16 Remote Module(ID1-16) Features: Built in LCD display 2 x RJ45 connectors Preset test modes for 10(100)Base-T, Token Ring, TP-PMD, AT & T 258A, EIA/TIA-568A/B USOC, 10Base-2(BNC) 4 additional user test modes can be configured Tests assignment, pairs, connection and shielding Terminator lopback test, cable testing with up to 16 remote units. Automatic cable identification Delivery includes 2 RJ45/BNC adapters, 30 cm patch cable and storage bag.

SY-L7142

LAN/USB CABLE-TESTER Correctly and quickly to read the testing cable configuration. Test Cable: RJ45 (UTP/STP), USB, RJ11/RJ12, BNC, Coaxial, RCA and modular cables Following standards: EIA/TIA 568A/568B,AT & T258A, ISDN, 10BASE-T, 100 BASE-TX, Token Ring, etc. Operation with AUTO Scan or step by step (Test) mode. Accessories: RJ45 (M/M) Cable x 1, RJ45/RJ11/RJ12 adapter x 2 and leather pouch x 1. Select accessories: (1) RJ45-Coaxial (F) adapter cable x 2, Coaxial (M/M) adapter x 1 (2) RJ45-RCA (F) adapter cable x 2.

5 SET/CTN/2'/13/14 KGS (G.W.)
1 PCS 1/4" FLAT SCREWDRIVER. 1 PCS #2 PHILLIPS SCREWDRIVER. 1 PCS 3/16" FLAT SCREWDRIVER. 1 PCS #1 PHILLIPS SCREWDRIVER. 1 PCS 1/8" FLAT SCREWDRIVER. 1 PCS #0 PHILLIPS SCREWDRIVER 1 PCS REVERSIBLE T10 &T15 TORQUE SCREWDRIVER. 2 PCS REVERSIBLE NUT DRIVER BIT: 3/16",1/4". 1 PCS THREE PRONGS HOLDER. 1 PCS TWEEZERS. 1 PCS IC INSERTION-EXTRACTION CLIPPER (FOR 14-48 PIN ICS). 1 PCS SOLDERING IRON. 1 PCS SOLDER REEL. 1 PCS SOLDERING STAND. 1 PCS 8" CRIMPING TOOL. 1 PCS 5" LONG NOSE PLIERS. 1 PCS PLASTIC CASE. 32 PCS TERMINALS(4 TYPES). 16 PCS SCREWS(2 TYPES). 6 PCS JUMPERS. 6 PCS WASHERS. 10 PCS REUSABLE CABLE TIE. BLOWING CASE.
10 SETS/CTN/1.7'/13.5/14.5 KGS (G.W.)
REVERSIBLE RATCHET HANDLE. BIT GROUP: 3 PCS FLAT: 1/8",3/16"1/4". 3 PCS PHILLIPS: #0,#1,#2. 3 PCS TORQUE:T10,T15,T20. 1 PCS ADAPTOR. 5 PCS SOCKET: 3/16",1/4",5/16",11/32",3/8". 5 PCS SOCKET: 6,7,8,9,10mm. THREE PRONGS HOLDER. TWEEZERS. IC INSERTION-EXTRACTION CLIPPER (FOR 14-48 PIN ICS). 200mm ALIGNMENT TOOLS. 9 PCS HEX KEYS. 5" LONG NOSE PLIERS. 4-1/2" SIDE CUTTER. FLASHLIGHT. PEN KNIFE. PRECISION WIRE STRIPPER. 6 PCS PRECISION SCREWDRIVER SET. SOLDER REEL. DESOLDERING PUMP. SOLDERING IRON. RED ZIPPER CASE.
10 SETS/CTN/1.8'/14/15 KGS

SY-9503 (31PCS)

1/8" FLAT SCREWDRIVER. 3/16" FLAT SCREWDRIVER. 1/4" FLAT SCREWDRIVER. # 1 PHILLIPS SCREWDRIVER. # 0 PHILLIPS SCREWDRIVER. # 2 PHILLIPS SCREWDRIVER. 3/16" NUT DRIVER. 1/4" NUT DRIVER. 6 PCS PRECISION SCREWDRIVER SET. 7 PCS HEX KEY. 4-1/2" SIDE CUTTER. 6" LONG NOSE PLIERS. 6" MINIATURE COMBINATION PLIERS. SOLDERING IRON STAND WITH SPONGE. DESOLDERING PUMP. SOLDER CORE. DIGITAL MULTIMETER. 3 WAY SOLDERING IRON. ELECTRIC TAPE. CARRING ZIPPER BAG.
6 SETS/CTN/2.1' /13.5/14.5 KGS (G.W.)
SY-9578 (70PCS) SY-5002 (86PCS) SY-9507 (46PCS)
5" LONG NOSE PLIERS. 4-1/2" SIDE CUTTER. 5" BENT NOSE PLIERS. 5" FLAT NOSE PLIERS. 6 PCS PRECISION SCREWDRIVER SET. SCREWDRIVER SET: 3.0 x75m, _5.0 x75mm, _6.0 x100mm, _6.0 x38mm. # 0 x75mm, _#1 x75mm, _# 2 x100mm,_# 2 x38mm. 3/16" NUT DRIVE. 1/4" NUT DRIVE. KNIFE. TWEEZERS-SERRATED INSIDE POINT. 7 PCS FOLDING HEX KEY WRENCH. BRUSH. ELECTRIC TAPE. 6" STAINLESS SCISSORS. 2 PCS FILE (ROUND & FLAT). 6" ADJUSTABLE WRENCH. 3 PCS SOLDERING AID TOOLS. UTILITY COMPONENT STORAGE BOX. 3M/10FT MEASURING TAPE. SOLDERING IRON STAND. SOLDER REEL. ANTI-STATIC DESOLDERING PUMP. 3 WAY SOLDERING IRON. DIGITAL MULTIMETER. BLACK SUITCASE.
5 SETS/CTN/3.4' /25/26 KGS (G.W.)

SY-5004 (48PCS)

1 PCS REVERSIBLE __1/8" & _ #0 MINI SCREWDRIVER (WITH POCKET CHIP). 1 PCS REVERSIBLE RATCH HANDLE. BIT GROUP: 5 PCS TORQUE: T8,T10,T15,T20,T25. 2 PCS PHILLIPS: # 1,2. 2 PCS FLAT: 5,6mm. 1 PCS ADAPTER. 5 PCS SOCKET: 3/16", 1/4", 5/16", 11/32", 3/8". 1 PCS BIT HOLDER. 1 PCS THREE PRONGS HOLDER. 1 PCS TWEEZERS. 1 PCS IC INSERTION-EXTRACTION CLIPPER (FOR 14-48 PIN ICS). 1 PCS PEN FLASHLIGHT. 1 PCS PLASTIC CASE. 12 PCS SCREWS(2 TYPE). 6 PCS JUMPERS. 6 PCS WASHERS. 1 PCS BLOWING CASE.

CV-200MK TS-1618

CV-200MK Nylon cable tie, 200mm PART# MCV-100 MCV-200 DESCRIPTION Cable marker tie, 100mm Cable marker tie, 200mm Sticky cable clamps

MPT-100

MULTI-PURPOSE TIE (100PCS, 6 COLORS)

Velcro cable ties

TS-1618

MCV-100

FEATURES:
UL Approved NYLON 66, 94V-2
Ideal for Sorting and Color Coding. For Interior/Exterior use. Specificatons: Tensile Strength: 40lbs/18.2kgs. Bundle Diameter: 1.75/44.5 mm Temperature rating: 185 F/85C Featrue: Weather-resistant Nylon , 100pcs & 6 colors. 20pcs Natural/20pcs Black/15pcs Red/15pcs Yellow/15pcs Green/15pcs Blue. Caution: Risk of injury/suffocation. Keep ties and packaging away from children. Use with designated tools and saftety glasses.

MCV-200

ANTI-Static Mats

YUSM10A/10B/10C

YUSM10A-595x250mm (K/B) YUSM10B-600x510mm (PC/XT) YUSM10C-600x600mm (PC/AT) With ground cord

UT-10 (CM-03)

Organize computer and audio cables, wires or cords of any kind! Size: 6-1/2 x 5/8, 10 pcs./ Pack

YUAS10

ANTI STATIC WRIST STRAP

CCF-5 5PCS/PACK

Reduce static electricity.

KS-306

Cable bridge Cable organizer

CABLE MANAGER

Cordless Wrist Strap (Effectiveness Testing)
Self-adhesive with excellent retention characteristics For cable fastening 10 different clips (6 x single, 2 x three, 2 x Secherclips)
5pcs in one set. Packing: 100sets/ctn/3.5kgs/4.0kgs /1.2cuft
Organize up to 12 cables. Consists of 2 side tracks, 2 cable brackets, and 6 cord clips. Packing:100sets/ctn/ 9kgs/10kgs/3.0cuft

CABLE RECESS BOX

CPU, monitor cables are properly stored. Safe management to avoid accident. Elegant shape. Accommodates 7 cables.
IDE/FDD/SCSI Round Flat Cable
ULTRA ATA 100(IDC 40F) Round Cable
IDE-A100R/18 - ULTRA ATA 100 ROUND CABLE, 18 inch. Length. IDE-A100R/24 - ULTRA ATA 100 ROUND CABLE, 24 inch Length. IDE-A100R/36 - ULTRA ATA 100 ROUND CABLE, 36 inch. Length. (Color-Transparent, Green, Yellow, Red, White)

UDMA-66/100 HDD Mobile Rack (1 Fan)- Aluminium cover) ITEM NO. DESCRIPTION IM-A101K Keylock only IM-A101KF Keylock+1 Fan IM-A101KPF Keylock with Ho Swappable+ 1 Fan UDMA-66/Fans HDD Mobile Rack(Aluminium cover ITEM NO. DESCRIPTION IM-A101KF2 Keylock+2 Fans IM-A101KPF2 Keylock with Hot Swappable+2 Fans UDMA-66/Fans HDD Mobile Rack (Aluminium cover) ITEM NO. DESCRIPTION IM-A101KF3 Keylock+3 Fans IM-A101KPF3 Keylock with Ho Swappable+3 Fans UDMA-66/100 HDD Mobile Rack Inner Tray Aluminium cover) ITEM NO. DESCRIPTION IM-A101T UDMA-66/100 Mobile Rack Inner Tray UDMA-66/Fans Mobile Rack Inner Tray ITEM NO. DESCRIPTION IM-A101T2 UDMA-66/100 Mobile Rack Inner Tray(1 Fan) UDMA-66/Fans Mobile Rack Inner Tray (Aluminium cover) ITEM NO. DESCRIPTION IM-A101T3 UDMA-66/100 Mobile Rack Inner Tray(2 Fans)
Power Cord / Notebook Car Adapter & USB Charging Cable
Power Cords Notebook Car Adapter

PC-WALL/PS06

USA,SAUDI ARABIA

PC-WALL/ESA

GERMANY ,FRANCE, BELGIUM, NETHERLANDS, BRAZIL, DENMARK, FINLAND, SWEDEN, NORWAY, AUSTRIA, INDIA, PAKISTAN

GW-P006VA

Car/Air Power Adapter for Notebook
Suitable for IBM, COMPAQ, DELL, HP, TOSHIBA, NEC, SHARP, TI, PHILIPS, AT&T, ACER, TWINHEAD, LEO, MITAC, ASUS, COMPAL, UANTA, NVENTEC, SOYO, CLEIVO, ARIMA, GVCetc. Specification : Size: 100 (L) x 60 (W ) x 40 (H ) mm Input Voltage & Current : 11-16VDC, 12A Output Power : 90W Max.

USB Charging Cable

PC-WALL/AU
FOR AUSTRALIA,NEW ZEALAND

PC-WALL/GF

GERMANY, FRANCE, BELGIUM, NETHERLANDS, BRAZIL, DENMAKR, FINLAND,SWEDEN, NORWAY,AUSTRIA, INDIA,PAKISTAN
USB Charging Cable For Most of the Cellular Phone models. Use your desktop computer or notebook USB port to charge your mobile phone, you don't need to carry the travel charger when you are in travelling.

PC-WALL/SA

FOR SOUTH AFRICA

PC-WALL/UK

U.K, IRELAND, SINGAPORE, MALAYSIA, KUWAIT U.A.E., MONACO

PC-3310-U01B

Cable Length: 60CM/For Nokia 3210/3310/8210/8850/8250/8210

PC-WALL/IC

ITALY,CHILE

PC-EP3

MONITOR POWER ADAPTOR CORD

PC-7110-U01B

Cable Length: 60CM/For Nokia 51XX/61XX/5210/7110/8810

PC-WALL/AS

FOR ASIA

POWER EXTENSION CORD.

KVM Switch
Mini KVM Switch 2 Port, Non-Power
Specification: All-in-one mini PS/2 KVM Switch Built-in KVM Cable Kit (1.8M, No Extra KVM Cable needer
2 Port KVM Switch MPC2000 / MPC2010
2 Port KVM Switch With Audio MPC2300

MPC2000 (SILVER)

MPC2010 (BLACK)

MPC2300 (SILVER)

USB KVM Switch with Data Transfer & Audio Function

Specification:

This USB KVM Switch allows you to control up to two computers from one keyboard, video monitor, mouse, and speaker and microphone console. With built-in USB 2.0 Data Transfer function, the unit supports a user-friendly oriented host-to-host networking application via both USB 2.0 and USB 1.1 interfaces. Enabled to operate with the USB interface, it provides a simple, cost-effective and reliable solution to a user.

Auto VGA Selector ( Multimedia Presentation / Smart Mini KVM )
Manual or auto select two VGA sources to one monitor. Support high VGA resolution 2048 x 1536 Auto-Scan capabilityfor easy-monitoring Support VGA,XGA,SVGA,Multi-sync.TFT-LCD monitors. Use push-button,extended switch(opt.)for manual selection. Auto switch to new connected VGAchannel.

SV-102

Monitor Switch
Easy select 2PCs or 4PCs to one monitor. Support VGA,XGA,SVGA,Multi-sync.TFT-LCD monitors.
Pocket, Desktop, Rackmount, 19 Slim Rackmout KVM Switch
Pocket KVM Switch ( One keyboard/Video Monitor/Mouse control 2 PCs )

KVM-102P

Desktop KVM Switch ( One keyboard/Video Monitor/Mouse control 2/4 PCs )

KVM-102M KVM-104M

Rackmount KVM Switch ( One keyboard/Video Monitor/Mouse control 8/16 PCs )
Compatible with MS-DOS,Windows,Linux,Unix. VGA resolution up to 2048 x 1536 Auto Scan monitoring function.

KVM-1080

KVM-1160
19Slim Rackmount PS2 KVM Switch ( Built in one extra Daisy Chain Port links up to eight levels )
Support iMac, Power Mac and Sun Microsystems with USB port (needwork with USB-PS2 adapter) Very High Video Qualit-Up to1920 x 1440, Bandwidth: 200MHz. Buzzer sound for switchingport confirmation.
19 Slim Rackmount USB KVM Switch ( Built in one extra Daisy Chain Port links up to eight levels )
USB1.1 Specification compliant Management multiple PCs, G3/G4 MACs, iMacs, SUN Microsystems with USB port from one USB keyboard, USB Mouse and Monitor. Buzzer sound for switchingport confirmation.

CS-108OD

CS108UOD

CS-1160D

CS-116UOD
Speaker, Audio / Video Switch & Projector Sharing Device

Speaker Switch

AS-108

AS-14 AS-104 AS-108

Audio Video Switch

AVS-401

AVS-402
Video Switcher & Projector Sharing Device
Feature: Support High Resolution Monitor / Projector Wire Remote Control Panel Control Splitters & Extender

VSB-41

VSB-41P

VSB-81

VSB-81R

VSB-62

VSB-84
KVM & Multi Cable / Manual / Auto Switch

KVM & Multi Cable

<< MULTI CABLE MBS1.8C
Description: CABLE-FOR VIDEO SWITCHER & PROJECTOR SHARING DEVICE Size:1.8M
<< KVM CABLE 2PB1.8C-1

Size:1.8M

MBS2.4C
Description: CABLE-FOR VIDEO SWITCHER & PROJECTOR SHARING DEVICE Size:2.4M

Reference Code 012D Description/Action Perform all actions before exchanging Failing Items Install Disk Unit K30 Concurrent maintenance informational reference code. 012E Install Disk Unit K31 Concurrent maintenance informational reference code. 012F Install Disk Unit K32 Concurrent maintenance informational reference code. 01AC Detected AC loss If system powers on normally or stays powered on after AC power failure, no replacement of parts may be needed. 0200 Remove Disk Unit 1 Concurrent maintenance informational reference code. 0201 Remove Disk Unit 2 Concurrent maintenance informational reference code. 0202 Remove Disk Unit 3 Concurrent maintenance informational reference code. 0203 Remove Disk Unit 4 Concurrent maintenance informational reference code. 0204 Remove Disk Unit 5 Concurrent maintenance informational reference code. 0205 Remove Disk Unit 6 Concurrent maintenance informational reference code. 0206 Remove Disk Unit 7 Concurrent maintenance informational reference code. 0207 Remove Disk Unit 8 Concurrent maintenance informational reference code. 0208 Remove Disk Unit K1 Concurrent maintenance informational reference code. 0209 Remove Disk Unit K2 Concurrent maintenance informational reference code. 020A Remove Disk Unit K3 Concurrent maintenance informational reference code. 020B Remove Disk Unit K4 Concurrent maintenance informational reference code. 020C Remove Disk Unit K5 Concurrent maintenance informational reference code. ACMODUL Failing Item
Reference Code 020D Description/Action Perform all actions before exchanging Failing Items Remove Disk Unit K6 Concurrent maintenance informational reference code. 020E Remove Disk Unit K7 Concurrent maintenance informational reference code. 020F Remove Disk Unit K8 Concurrent maintenance informational reference code. 0210 Remove Disk Unit K9 Concurrent maintenance informational reference code. 0211 Remove Disk Unit K10 Concurrent maintenance informational reference code. 0212 Remove Disk Unit K11 Concurrent maintenance informational reference code. 0213 Remove Disk unit K12 Concurrent maintenance informational reference code. 0214 Remove Disk Unit K13 Concurrent maintenance informational reference code. 0215 Remove Disk Unit K14 Concurrent maintenance informational reference code. 0216 Remove device 1 Concurrent maintenance informational reference code. 0217 Remove device 2 Concurrent maintenance informational reference code. 0218 Remove Disk Unit 9 Concurrent maintenance informational reference code. 0219 Remove Disk Unit 10 Concurrent maintenance informational reference code. 021A Remove Disk Unit 11 Concurrent maintenance informational reference code. 021B Remove Disk Unit 12 Concurrent maintenance informational reference code. 021C Remove device 3 Concurrent maintenance informational reference code. 021D Remove Disk Unit K15 Concurrent maintenance informational reference code. 021E Remove Disk Unit K16 Concurrent maintenance informational reference code. Failing Item

Reference Code 050D Description/Action Perform all actions before exchanging Failing Items Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K6, and the bus was released. You must reinitialize the operation to continue. 050E Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K7, and the bus was released. You must reinitialize the operation to continue. 050F Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K8, and the bus was released. You must reinitialize the operation to continue. 0510 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K9, and the bus was released. You must reinitialize the operation to continue. 0511 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K10, and the bus was released. You must reinitialize the operation to continue. 0512 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K11, and the bus was released. You must reinitialize the operation to continue. 0513 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K12, and the bus was released. You must reinitialize the operation to continue. 0514 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K13, and the bus was released. You must reinitialize the operation to continue. 0515 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K14, and the bus was released. You must reinitialize the operation to continue. Failing Item
Reference Code 0516 Description/Action Perform all actions before exchanging Failing Items Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of device 1, and the bus was released. You must reinitialize the operation to continue. 0517 Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of device 2, and the bus was released. You must reinitialize the operation to continue. 0518 Timeout, no action detected. Reinitialize the operation. No action was detected for the installation or removal of disk unit 9, and the bus was released. You must reinitialize the operation to continue. 0519 Timeout, no action detected. Reinitialize the operation. No action was detected for the installation or removal of disk unit 10, and the bus was released. You must reinitialize the operation to continue. 051A Timeout, no action detected. Reinitialize the operation. No action was detected for the installation or removal of disk unit 11, and the bus was released. You must reinitialize the operation to continue. 051B Timeout, no action detected. Reinitialize the operation. No action was detected for the installation or removal of disk unit 12, and the bus was released. You must reinitialize the operation to continue. 051C Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of device 3, and the bus was released. You must reinitialize the operation to continue. 051D Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K15, and the bus was released. You must reinitialize the operation to continue. 051E Timeout, no action detected. Reinitialize the operation No action was detected for the installation or removal of disk unit K16, and the bus was released. You must reinitialize the operation to continue. Failing Item

Reference Code 902C Description/Action Perform all actions before exchanging Failing Items Battery Power Unit test was aborted. The battery power unit test was aborted. No action required. This reference code is logged for information only. 902D Addressed frame is not in SPCN configuration table. The addressed frame is not in the SPCN configuration table. No action required. This reference code is logged for information only. 9031 Frame-to-Frame Communications Failure The SPCN detected a BCC error on a transmission from another frame. The transmission is attempted again. No action required. This reference code is logged for error analysis only. 9032 SPCN Communications Failure, unit to rack. The frame detected a BCC error on a transmission from a secondary node to the frame. The transmission is attempted again. No action required. This reference code is logged for error analysis only. 9033 SPCN Communications Failure, rack to unit. A secondary node detected a BCC error on a transmission from the frame. The transmission is attempted again. No action required. This reference code is logged for error analysis only. 9034 Unsupported Packet Size The receiving node detected a packet exceeding 70 bytes. The frame can also return this code if a secondary node returns more than 10 bytes to a PAS command. No action required. This reference code is logged for error analysis only. 9035 Secondary SPCN node timeout. A secondary SPCN node did not respond to a command. The command was attempted again and failed. No action required. This reference code is logged for error analysis only. 9036 Frame Timeout One or more frames did not respond to a command. The command is attempted again. No action required. This reference code is logged for error analysis only. 903B Invalid Packet Length for data sent. The number of bytes sent or received does not match the number of bytes specified in the command. No action required. This reference code is logged for error analysis only. 9041 Invalid Load Type The down load was successful, but the wrong type of Licensed Internal Code was loaded. The operation was attempted again but was not successful. Exchange the failing items for the node reporting the fault. AJDG301 TWRCARD Failing Item
Reference Code 9042 Description/Action Perform all actions before exchanging Failing Items EEPROM Failure The EEPROM in an SPCN node cannot be written successfully. Exchange the SPCN node reported in the failure. 9043 Download Failure The Licensed Internal Code download to an SPCN node was completed but was not successful. Exchange the failing SPCN node. 9046 QDS Packet Sequence Error The Packet Sequence number is wrong. The download was stopped. 9047 QDS Block Sequence Error The Block Sequence number is wrong. The download was stopped. 9048 The SPCN ROS and EEPROM LIC is not compatable. The LIC levels in the nodes ROS and EEPROM are not compatible. Exchange the failing items for the failing node. 9080 Undefined Status Code An SPCN node returned an unknown status code. Exchange the failing SPCN node. 90F0 A frame was dropped from the SPCN configuration. A frame was dropped from the SPCN configuration. This is usually caused by a loss of ac power or a problem with the frame-to-frame cable. 90F1 A frame was added to the SPCN configuration. No action required. This reference code is logged for information only. 9100 Battery capacity test completed. No action required. This reference code is logged for information only. 9101 TWRCARD CTLPNL A Licensed Internal Code timeout occurred. The SPCN failed to respond to SVCPROC a Licensed Internal Code command. VLIC-SPCN Timeout Assign Permanent Address command failure A node failed to perform an Assign Permanent Address command. 9103 Download Initialize Timeout An SPCN node failed to enter the download state after an Initialize for Download command. Exchange the failing SPCN node. 9104 Download Completion Timeout An SPCN node failed to leave the download state. Exchange the failing SPCN node. TWRCARD TWRCARD TWRCARD TWRCARD CBLALL TWRCARD BACKPLN TWRCARD AJDG301 TWRCARD TWRCARD TWRCARD Failing Item TWRCARD

Reference Code 9033 Description/Action Perform all actions before exchanging Failing Items SPCN Communications Failure, rack to unit. A secondary node detected a BCC error on a transmission from the frame. The transmission is attempted again. No action required. This reference code is logged for error analysis only. 9034 Unsupported Packet Size The receiving node detected a packet exceeding 70 bytes. The frame can also return this code if a secondary node returns more than 10 bytes to a PAS command. No action required. This reference code is logged for error analysis only. 9035 Secondary SPCN node timeout. A secondary SPCN node did not respond to a command. The command was attempted again and failed. No action required. This reference code is logged for error analysis only. 9036 Frame Timeout One or more frames did not respond to a command. The command is attempted again. No action required. This reference code is logged for error analysis only. 903B Invalid Packet Length for data sent. The number of bytes sent or received does not match the number of bytes specified in the command. No action required. This reference code is logged for error analysis only. 9041 Invalid Load Type The down load was successful, but the wrong type of Licensed Internal Code was loaded. The operation was attempted again but was not successful. Exchange the failing items for the node reporting the fault. 9042 EEPROM Failure The EEPROM in an SPCN node cannot be written successfully. Exchange the SPCN node reported in the failure. 9043 Download Failure The Licensed Internal Code download to an SPCN node was completed but was not successful. Exchange the failing SPCN node. 9046 QDS Packet Sequence Error The Packet Sequence number is wrong. The download was stopped. 9047 QDS Block Sequence Error The Block Sequence number is wrong. The download was stopped. 9048 The SPCN ROS and EEPROM LIC is not compatable. The LIC levels in the nodes ROS and EEPROM are not compatible. Exchange the failing items for the failing node. TWRCARD AJDG301 TWRCARD TWRCARD TWRCARD AJDG301 TWRCARD Failing Item
Reference Code 9080 Description/Action Perform all actions before exchanging Failing Items Undefined Status Code An SPCN node returned an unknown status code. Exchange the failing SPCN node. 90F0 A frame was dropped from the SPCN configuration. A frame was dropped from the SPCN configuration. This is usually caused by a loss of ac power or a problem with the frame-to-frame cable. 90F1 A frame was added to the SPCN configuration. No action required. This reference code is logged for information only. 9100 Battery capacity test completed. No action required. This reference code is logged for information only. 9101 TWRCARD CTLPNL A Licensed Internal Code timeout occurred. The SPCN failed to respond to SVCPROC a Licensed Internal Code command. Assign Permanent Address command failure A node failed to perform an Assign Permanent Address command. 9103 Download Initialize Timeout An SPCN node failed to enter the download state after an Initialize for Download command. Exchange the failing SPCN node. 9104 Download Completion Timeout An SPCN node failed to leave the download state. Exchange the failing SPCN node. 9105 Load Damaged Timeout An SPCN node failed to enter the operational state. Exchange the failing SPCN node. 9106 An SPCN LID was not found. No action required. This reference code is logged for information only. 9107 An SPCN microcode download is required. No action required. This reference code is logged for error analysis only. 9108 A status change occured in one of the SPCN nodes. No action required. This reference code is logged for information only. 9109 Licensed Internal Code part number is not correct. The AROS part number field was not updated to the correct level after the system attempted to load new Licensed Internal Code. 9110 Battery Power Unit capacity test failed. The battery power unit was not able to pass the capacity test. BATRY TWRCARD TWRCARD TWRCARD TWRCARD TWRCARD VLIC-SPCN Timeout TWRCARD CBLALL Failing Item TWRCARD BACKPLN

No Free Entries No free entries were found during System Frame processing.
ARA Failure An Assign Frame Address Failure occurred during ARA Preprocessing.
Undefined status Undefined Status occurred during Frame or STF processing.
BCC Fault A BCC Error was detected during Network post processing.
Reference Code 9286 Description/Action Perform all actions before exchanging Failing Items Length Check Error. Length Check occurred during SPCN post processing. 9287 Undefined status Undefined Status occurred during Command processing. 9288 Configuration Error A configuration error was detected during System Frame processing. 9289 Invalid Packet Length for data sent. Invalid Packet Length occurred for data exchanged. C62E SPCN Network Fault An SPCN frame-to-frame communication failure was detected. SRNPU or POSORMU. CB15 EEPROM Failure TWRCARD Failing Item TWRCARD AJDG301 TWRCARD AJDG301 TWRCARD AJDG301 AJDG301 TWRCARD TWRCARD CBLALL
Table 4. For system Model 890 formatted: 1xxA-xxxx or 1xxB-xxxx with table identifier A0, SPCN Reference Codes: For SRCs in this table, where x is a variable number or character, xnnn or xxnn will appear in the table representing the variable.
Reference Code 0876 0D06 1C06 CE16 Description/Action Perform all actions before exchanging Failing Items BPR-1 communication fault BPR-2 communication fault BPR-3 communication fault BPA 350V power failure Cage air flow cooling problem BPC-A to BPC-B communication fault Check cable and connector pins between the two BPCs before replacing BPCs. D216 D616 D716 D816 D916 DA16 DB16 DC16 DD16 DF16 E106 E206 F4X6 BPA-A to BPA-B communication fault UPS utility failure UPS battery low condition was detected UPS reported a bypass active UPS utility power restored UPS installed UPS not available UPS battery low condition was reset UPS reported bypass no longer active UPS failure Critical logic overtemperature Ambient room temperature limit exceeded Hardware configuration cannot support N-mode power MAPPWR UPSUNIT UPSUNIT UPSUNIT UPSUNIT UPSUNIT UPSUNIT UPSUNIT UPSUNIT UPSUNIT MAPPWR MAPPWR MAPPWR Failing Item MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR BPCPWR
Reference Code F806, F906, FA06 FDB6 FE06, FE16 FE56 FE66 FE76 X115 X215 X315 X415 X515 X615 X715 X925 XA25 XX0X XX11 XX13 XX17 XX21 XX22 Description/Action Perform all actions before exchanging Failing Items BPC AC power loss or phase missing BPC Room EPO switch has been detected open BPC UEPO switch is in the bypass position BPR-1 communication fault BPR-2 communication fault BPR-3 communication fault Processor MDA-1 cable fault Processor MDA-2 cable fault Processor MDA-3 cable fault Processor MDA-4 cable fault Processor DCA-1 cable fault Processor DCA-2 cable fault Processor DCA-3 cable fault Processor DCA-4 cable fault Processor DCA-5 cable fault BPA FRU failure not isolated BPC fault BPC Seeprom VPD fault BPF Fan fault BPD-1 fault BPC to BPD-1 communication fault Failing Item MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR MAPPWR BPCPWR BPCPWR BPFPWR BPDPWR BPDPWR BPCPWR MAPPWR BPDPWR BPDPWR BPDPWR BPCPWR MAPPWR BPDPWR BPRPWR BPRPWR BPCPWR MAPPWR BPRPWR BPRPWR BPRPWR BPCPWR MAPPWR BPRPWR BPRPWR BPRPWR BPCPWR MAPPWR BPRPWR

Failing Item BACKPLN Description Card enclosure or backplane Document Description Problem Analysis; Symbolic FRU Isolation
Failing Item CMPRES1 DEVTERM DISKDRV STORIOA SVCDOCS Description Compressed device and compression IOA are not compatible Device terminator Disk drive and logic card Storage I/O adapter Customer engineer directed to system problem analysis Document Description Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation
(632x, 6330, 6336) Optical Storage Unit Reference Codes
An optical storage unit failure occurred. Notes: 1. If the system is available, use online diagnostic tests when possible. 2. Search the problem log (WRKPRB) for a recent optical storage entry that may assist in analyzing the problem. The WRKPRB entry will provide a unit reference code that can be found in the following table. 3. Use the Hardware Service Manager (HSM) verify function (via DST or SST) and verify that the unit is operating correctly. Perform the following: 1. If the system is available, attempt the failing operation again with an optical media that is known to be good. Does the operation complete successfully? v Yes: The original optical media may be defective, or the problem may be intermittent. Attempt the failing operation again with the original optical media to verify. This ends the procedure. v No: Look at the 4 rightmost characters of the Data display for word 1. These 4 characters are the unit reference code. Find the unit reference code in the following table. For more on the Failing Item column entries, see Table 2. Optical Storage Unit Failing Items Details, which follows the reference code table below. Table 1. (632x, 6330, 6336) Optical Storage Unit Reference Codes
Reference Code C002 Description/Action Perform all actions before exchanging Failing Items SCSI selection or reselection timeout occurred Failing Item FI00870 FI01106 FI01112 MEDIA FI01140 FI01141 DEVTERM CDTRAY FI00870 FI00870

C010 C020

Undefined sense key returned by device Device internal configuration error

632x, 6330, 6336

Reference Code C100 Description/Action Perform all actions before exchanging Failing Items SCSI bus command error occurred Failing Item FI00870 FI01106 FI01112 MEDIA FI01140 FI01141 DEVTERM CDTRAY FI00870 FI01106 FI01112 MEDIA FI01140 FI01141 DEVTERM CDTRAY

Reference Code FFFE Description/Action Perform all actions before exchanging Failing Items Tape unit detected a read error on the tape medium Perform the Action for reference code 030B. FFFF Tape unit detected a write error on tape medium Perform the Action for reference code 030B. Failing Item ML2TMED 46G2227 46G3934 42F7300 ML2TMED 46G2227
Table 4. Model 012 Tape Drive Failing Items
Failing Item 17G1500 42F7300 46G2227 46G2599 46G3934 AJEDA00 ANYBUS ML2TMED UL2CLN UL2CNFG UL2USR1 UL2WAIT Description Internal signal cable Fan Tape drive Terminating plug Power supply I/O processor Licensed Internal Code IOP card bus error Defective tape Tape unit needs cleaning Tape configuration detected by I/O processor; not valid Operator action required Wait to next IPL or perform TU-PIP4 Document Description 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide Service Functions; APAR or LICTR Problem Analysis; Symbolic FRU Isolation 7208 Model 012 5.0GB External 8mm Tape Drive Service Guide Magnetic tape subsystem operators information Magnetic tape subsystem operators information Magnetic tape subsystem operators information Problem Analysis
(9348) Tape Unit Reference Codes
A tape or a 9348 Tape Unit failure occurred. Note: If the system is available, use the online diagnostic tests when possible. Use the Work with Problem ( WRKPRB) command to determine if a recent problem has been entered in the problem log, or use the Verify Tape (VFYTAP) command. Other helpful commands are Work with Hardware Resources (WRKHDWRSC *STG) and Work with Configuration Status (WRKCFGSTS *DEV *TAP). For tape device and IOP reset procedures, see TU-PIP4. 1. Verify that the 9348 Tape Unit is powered on and that the interface cable connections are correct for each 9348 Tape Unit. 2. Clean the tape path as described in the 9348 Tape Unit Service Information. 3. Load the first tape and start a type D IPL from the system unit control panel. Does the IPL complete successfully? v Yes: The problem has been corrected.
This ends the procedure. v No: Obtain another copy of the tape. Repeat this step using the new tape. If this does not correct the problem, continue with the next step. 4. Look at the 4 rightmost characters of the Data display for word 1. These 4 characters are the unit reference code. 5. If the tape unit indicator panel shows an error condition, see the 9348 Tape Unit Service Information and find the unit reference code.
(9427) Tape Unit Reference Codes
The tape library detected a failure. 1. Look at the 4 rightmost characters of the Data display for word 1. These 4 characters are the unit reference code. 2. Find the unit reference code in the following table. For more on the Failing Item column entries, see Table 2. Tape Unit Failing Items Details, which follows the reference code table below. Table 1. (9427) Tape Unit Reference Codes

Failing Item SVCPROC SVCPROC

SVCPROC

SYSUNIT BUS1 AJDGP01 SVCPROC IPLINTF
LSMEDIA CTLPNL LSMEDIA AJDGP01 SVCPROC AJDGP01
Reference Code Description/Action Perform all actions before exchanging Failing Items CSP to VPD Collector interface error. CSP to VPD Collector interface error. Failing Item SVCPROC CTLPNL VPDCONC SVCPROC SYSUNIT PROC PROC0 PROC1 PROC2 PROC3 JTPORT MSTORE MSTORE HSLCTLR CLKCARD CTLPNL AJDG301

4661 to 4690

System processor card failure System processor card failure System processor card failure System processor card failure System processor card failure Main storage failure Main storage failure System processor card failure System processor card failure Problem detected with control panel Service processor LIC problem If this SRC is displayed at the control panel, then record all of the SRC data words. Perform a main storage dump using control panel function 22, and report the problem to the next level of support. If this SRC is displayed at the system console dump manager screen then save the main storage dump and report the problem to service.

4691 to 4697

Service processor Licensed Internal Code Perform INT-PIP24.

4698 4699

Operator/User Error Service processor Licensed Internal Code Perform INT-PIP24.

OPUSR AJDGP01

AJDGP01 AJDG301 AJDG301
Service processor LIC problem Record all the SRC data words, attempt a main storage dump, and replace the FRUs listed if necessary.
Service processor Licensed Internal Code Perform INT-PIP24, then replace the FRUs listed if necessary.
Service processor Licensed Internal Code If this SRC is displayed at the system console dump manager screen then save the main storage dump and report the LIC failure to service. If this SRC is displayed at the control panel then perform INT-PIP24.
AJDGP01 SYSUNIT SVCPROC AJDGP01 SVCPROC SYSUNIT
Reference Code 8FF0 Description/Action Perform all actions before exchanging Failing Items Operator/User Error Any device attached to Bus 1 Information only, no service action required Service processor error log entry. If the secondary refcode is 806A, a successful download of control panel code has occured. If the secondary refcode is 8EEE, one of the following conditions may have occured. Operation was successful but current keylock position was not in Auto or normal. The Time-of-Day (TOD) chip had to be reset due to an invalid power-up state. TOD requests will not work successfully until a write TOD is done (CHGSYSVAL QDATE). Timed-Power-On request has been acknowledged. Power on sequences must be set for valid months, days, hours, minutes, and seconds, for future times, and for times when the system will be powered off. 8FF1 System down, condition reported Failing Item UCSUSER JTPORT

Reference Code 0022 Description/Action Perform all actions before exchanging Failing Items Device detected storage or data overrun Perform TWSC-PIP1. 0023 Device detected null or attribute exception error Perform TWSC-PIP1. 0024 Device detected wrong start command from WS IOP Perform TWSC-PIP1. 0025 WS IOP detected wrong exception response from device Perform TWSC-PIP1. 0026 WS IOP detected not valid pass-through command Perform TWSC-PIP1. 0049 WS IOP detected wrong request or response from device Perform TWSC-PIP1. 0082 WS IOP detected wrong device type from device Perform TWSC-PIP1. 0090 WS IOP detected no status change from device Perform TWSC-PIP1. 0091 WS IOP detected busy time-out from device Perform TWSC-PIP1. 0100 Device no response time-out; temporary error FI00601 FI00610 FI00601 FI00610 FI00601 FI00602 FI00610 FI00602 FI00601 GAU7777 GAU8888 FI00610 FI00615 Failing Item FI00601 AJLYD01 FI00610 FI00601 FI00610 FI00601 AJLYD01 FI00610 FI00601 FI00610 GAU9999 FI00610 FI00601 FI00610 FI00601
WS IOP detected parity error from device Is the problem intermittent? No Yes Perform the following procedures: 1. INT-PIP5 2. INT-PIP14 Perform TWSC-PIP1.
Reference Code 0104 Description/Action Perform all actions before exchanging Failing Items Device detected parity error from WS IOP Is the problem intermittent? No Yes Perform the following procedures: 1. INT-PIP5 2. INT-PIP14 Perform TWSC-PIP1. 0105 WS IOP detected error when transmitting data Is the problem intermittent? No Yes Perform the following procedures: 1. INT-PIP5 2. INT-PIP14 Perform TWSC-PIP1. 0106 WS IOP detected wrong data from device Is the problem intermittent? No Yes Perform the following procedures: 1. INT-PIP5 2. INT-PIP14 Perform TWSC-PIP1. 0107 WS IOP detected wrong address from device Is the problem intermittent? No Yes Perform the following procedures: 1. INT-PIP5 2. INT-PIP14 Perform TWSC-PIP1. 0108 WS IOP detected device power turned off, and then on Perform TWSC-PIP1. 0109 WS IOP detected wrong device response to start command Perform TWSC-PIP1. 0111 WS IOP detected wrong keyboard scan code from display Perform TWSC-PIP1. 0120 Device detected wrong command or device ID from WS IOP Perform TWSC-PIP1. GAUEEEE FI00601 FI00601 FI00610 FI00601 AJLYD01 FI00610 FI00601 AJLYD01 FI00610 FI00601 GAU8888 GAU7777 FI00610 FI00601 FI00602 GAU8888 FI00610 FI00602 FI00601 GAU8888 FI00610 FI00615 Failing Item FI00602 FI00601 GAU7777 FI00610
Reference Code 0121 Description/Action Perform all actions before exchanging Failing Items Device detected not valid value from WS IOP Perform TWSC-PIP1. 0122 Device detected storage or data overrun Perform TWSC-PIP1. 0123 Device detected null or attribute exception error Perform TWSC-PIP1. 0124 Device detected wrong start command from WS IOP Perform TWSC-PIP1. 0125 WS IOP detected wrong exception response from device Perform TWSC-PIP1. 0126 WS IOP detected not valid pass-through command Perform TWSC-PIP1. 0149 WS IOP detected wrong request or response from device Perform TWSC-PIP1. 0172 WS IOP detected error downloading printer definition table WS IOP detected error downloading printer definition table WS IOP detected error downloading printer definition table Failing Item FI00601 AJLYD01 FI00610 FI00601 AJLYD01 FI00610 FI00601 FI00610 FI00601 AJLYD01 FI00610 FI00601 FI00610 GAU9999 FI00610 FI00601 FI00610 AJDG301 FI00601 FI00601 AJLYD01 CAUPDT AJDG301 FI00601 CAUPDT FI00601 FI00601 AJLYD01 FI00601 AJLYD01 GAUDMCC FI00601 FI00605 MAUFFFF FI00601 FI00610 FI00601

Reference Code 500D 56EA Description/Action Perform all actions before exchanging Failing Items Incorrect command value sent by Licensed Internal Code Procedure error in Licensed Internal Code Communications controller storage not available Clear-to-send signal dropped on modem interface Failing Item AJDG301 CXCMAXI AJDG301 CXCBUSY GXCLINK FI00704 CXCCTSV FI00719 FI00701 FI00701 FI00704 FI00719 AJLAG01 FI00704 FI00701 GXCLINK FI00719 CXCNPRT FI00700 FI00705 FI00704 GXCLINK FI00701 FI00719 AJLAG01 CXCENCD CXCINAT GXCLINK FI00704 FI00705 FI00700 CXCSTAD FI00701 CXCDTAR FI00719 CXCMRTY GXCLINK CXCRPTO FI00701 FI00704 CXCMRTY FI00705 CXCENCD FI00700 CXCDTAR FI00719 GXCLINK FI00705 FI00704 FI00700 CXCMRTY FI00719 FI00701 FI00700
Data-set-ready turn-on time-out on modem interface
Data-set-ready dropped on modem interface
Nonproductive receive time-out while receiving from remote
No data received from remote equipment; time-out
Remote equipment did not respond causing an idle-time-out
Retry limit reached for sending frames to remote equipment
Reference Code Description/Action Perform all actions before exchanging Failing Items Retry limit reached for sending poll frame to remote Could not send frame to remote equipment; local problem Failing Item FI00700 CXCMODU FI00704 CXCDTAR FI00701 FI00719 FI00730 AJLAG01 CXCSTAD GXCBBBB FI00615

5722 A000 B000

Wrong command value sent by OS/400 licensed program Too many devices active on the workstation IOP WS IOP fails to report part, model and serial number Perform WSAC-PIP1.
C000, D000 D001 F003 FFFF
WS IOP error not known Wrong or no external communications cable installed WS IOA buffer utilization threshold exceeded temporarily User believes there is a problem Reference code FFFF is assigned by the ANZPRB (Analyze Problems) for user-detected errors. Run ANZPRB again if the problem still exists or look in the problem log (WRKPRB) for possible failing FRUs.
AJLAG01 FI00631 AJLAG01 AJLAG01 UXCFF00
Failing Item AJDG301 AJLAG01 CXCBUSY CXCCONF CXCCPTO CXCCTSV CXCDTAR CXCENCD CXCINAT CXCMAXI CXCMODU CXCMRTY CXCMSTA CXCNPRT CXCRPTO CXCSNDT CXCSTAD CXCTEMP Description Vertical Licensed Internal Code Licensed Internal Code Too many communications lines in use Configuration or OS/400 licensed program CNNPOLLTMR value in CRTLINSDLC command CTSTMR value in CRTLINSDLC command LINESPEED value in CRTLINSDLC command NRZI value in CRTLINSDLC command INACTTMR value in CRTLINSDLC command MAXFRAME value in CRTLINSDLC command MODULUS value in CRTLINSDLC command FRAMERTY value in CRTLINSDLC command MAXCTL value in CRTLINSDLC command NPRDRCVTMR value in CRTLINSDLC command IDLTMR value in CRTLINSDLC command SHMNODE value in CRTLINSDLC command STNADR value in CRTCTL_____command No failure found Document Description Service Functions; APAR or LICTR Service Functions; APAR or LICTR Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration

v No: Continue with the next step. 4. Choose one of the following: v If you are working on a system Model 270 or 820, then continue with the next step. v If you are working on a system Model 830, 840, SB2, or SB3, then go to step 6 of this procedure. 5. Is the reference code B4FF 00B0 or B4FF 00B1? v No: Contact your next level of support. This ends the procedure. v Yes: If the reference code is B4FF00B1, then the System Unit Backplane may be the failing item. If the reference code is B4FF00B0, then the System Unit Backplane may be the failing item, or the failure may be caused by the Licensed Internal code. For either reference code, perform the following: Note: If the reference code B4FF 00B1 occurred after a power outage, try removing incoming power, reapplying it, and then retrying the IPL. a. Before exchanging any parts, verify that all connections to the System Unit Backplane are secure. b. Exchange the System Unit Backplane in position MB1. For Model 270: To determine the location, CCIN, part number, and removal and installation procedure for the System Unit Backplane, locate card position MB1 in the FRU Locations and Failing Components table for the processor feature code of the Model 270 you are working on. Use Locations -- Model 270 and the processor feature code to determine which Model 270 locations diagram and FRU Locations and Failing Components table to use. For Model 820: To determine the location of the System Unit Backplane, see Model 820 locations. To determine the CCIN, part number, and removal and installation procedure for the System Unit Backplane, locate card position MB1 and FRU name System Unit Backplane in Model 820. If this does not fix the problem, contact your next level of support. This ends the procedure. 6. Is the reference code B4FF 00B0 or B4FF 00B1? v Yes: Continue with the next step. v No: Go to step 8 on page 247 of this procedure. 7. If the SRC B4FF 00B1 occurred after a power outage, remove the incoming power, wait 30 seconds, reapply the power and retry the IPL. If the system IPLs without the error, the procedure is complete. If the reference code is B4FF00B1, then the HSL I/O bridge card may be the failing item. If the reference code is B4FF00B0, then the HSL I/O bridge Card may be the failing item, or the failure may be caused by the Licensed Internal code. For either reference code, exchange HSL I/O bridge card in location C08. To determine the CCIN, part number, and removal and installation procedure, locate card position C08 and FRU name HSL I/O bridge card from the following: v For Models 830 and SB2, see Locations -- Models 830, SB2 System Unit with FC 9074 Base I/O Tower. v For Models 840 and SB3, see Locations -- Models 840, SB3 System Unit with Processor Tower and FC 9079 Base I/O Tower. Did this fix the problem?
v Yes: This ends the procedure. v No: Exchange the Tower Card in position CB1. To determine CCIN, part number, and removal and installation procedure, locate card position CB1 and FRU name Tower Card from the following: For Model 830, SB2 see Locations -- Models 830, SB2 System Unit with FC 9074 Base I/O Tower. For Model 840, SB3 see Locations -- Models 840, SB3 System Unit with Processor Tower and FC 9079 Base I/O Tower. If the problem still has not been fixed, contact your next level of support. This ends the procedure. 8. Is the reference code B4FF00B3? v No: Contact your next level of support. This ends the procedure. v Yes: Continue with the next step. 9. Choose one of the following: v The system cannot find any processors. If you are working on a Model 830 or a Model 840, the PCI drawer may be the failing item. See Symbolic FRU TWRPLNR. If that fails to correct the problem, exchange the J-Tag cable. See the Power and Signal cables table for the system on which you are working. If that fails to correct the problem, any processor may be the failing item. Refer to Symbolic FRU ANYPROC for the procedure to determine processor location and part information. v For system Models 830 and SB2: The Clock card in location M06A may be the failing item. To determine the CCIN, part number, and removal and installation procedure, locate card position M06A and FRU name Clock Card in Locations -- Models 830, SB2 System Unit with FC 9074 Base I/O Tower. Exchange the failing item. Did this fix the problem? Yes: This ends the procedure. No: Exchange the network interface controller (NIC) card. To determine the CCIN, part number, and removal and installation procedure, locate card position M06 and FRU name network interface controller (NIC) card in Locations -- Models 830, SB2 System Unit with FC 9074 Base I/O Tower. If the problem still is not fixed, contact your next level of support. This ends the procedure. v For system Models 840 and SB3: The network interface controller (NIC) card in location M17 may be the failing item. To determine the CCIN, part number, and removal and installation procedure, locate card position M17 and FRU name network interface controller (NIC) card in Locations -Models 840, SB3 System Unit with Processor Tower and FC 9079 Base I/O Tower. Exchange the failing item. If this did not fix the problem, contact your next level of support. This ends the procedure. Instructions for Model 890 An SRC starting with B4FF indicates the system failed to complete an IPL because of a processor related problem. Find the full SRC from the list below and take the indicated action to correct the problem.

B4FF00B0 or B4FF00B1: Indicates a problem with either the Service Processor code or the load source RIO Bridge. 1. If the SRC B4FF 00B1 occurred after a power outage, remove the incoming power, wait 30 seconds, reapply the power and retry IPL. If the system IPLs without the error, the procedure is complete. 2. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected, continue with the next step. 3. Replace the load source RIO Bridge. For Model 890, replace the Tower card in the base I/O Unit. See Locations Model 980 4. B4FF00B3: This indicates a problem with a processor or Service Processor code. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected for the Model 890, replace the MCM module in location M21. See Locations Model 890 5. B4FF00B4: This indicates a problem with a processor or Service Processor code. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected for the Model 890, replace the MCM module in location M11. See Locations Model 890 6. B4FF00B5: This indicates a problem with a processor or Service Processor code. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected for the Model 890, replace the MCM module in location M16. See Locations Model 890 7. B4FF00B6: This indicates a problem with a processor or Service Processor code. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected for Model 890, replace the MCM module in location M14. See Locations Model 890 8. B4FF00B7: The system did not pass a check for a minimum hardware configuration present in order for the IPL to continue. The group of chips failed to meet the requirement are given in word 13 of the SRC. Check to see if the PCI cards are properly seated in the card slots, and that any cables are cleaned and properly connected to the cards. Then re-IPL the system. If that does not correct the problem, replace the Service Processor. See the Locations and addresses page for the model you are working on. If that does not correct the problem, call your next level of support. 9. B4FF0EAF: Indicates a problem with Service Processor code. Load AJDGP01 from RETAIN. IPL the system. If the problem is not corrected, contact your next level of support.
(B6xx) Licensed Internal Code (LIC) Reference Codes

Reference Code 5344 Description/Action Perform all actions before exchanging Failing Items Secondary partition not running at optimum. The interactive performance specified in the configuration data for this partition could not be met. Contact your next level of support. 5350 Secondary partition software release not supported. The logical partition software version is outside the supported release delta. Check the Release Delta from the Primary partition Display Partition Release Level screen. Check the LPAR documentation for the release level of the Primary partition and determine what the supported Release Delta is. 5380 System LIC program exception occurred Record the Procduct Activity Log (PAL) hex data for this SRC or print the PAL entry. Contact your next level of support. 5390 System LIC program exception occurred Record the Product Actvity Log (PAL) hex data for this SRC or print the PAL entry. Contact your next level of support. SLIC I/O DASD subsystem error recovery in progress. System bus error The copper bus, bus 4 in the SPD migrated tower, is inoperative due to a stuck line or a parity error. Any SPD system bus-related hardware on bus 4 may have failed including the HSL I/O bridge or HSL cable connecting SPD bus 4 to the HSL loop. Perform BUS-PIP1. 6901 Bus Expansion Adapter card failed The copper bus, the first SPD bus in the system unit or migrated tower, has failed due to an internal chip error on the local bus adapter. Perform BUS-PIP1. For this reference code the failing item list presented in the Service Action Log can be different from the failing item list documented here. That is due to the differences in system models and features installed. If the Service Action Log is available then use the failing item list presented there for servicing this reference code. If the Service Action Log is not available then use the failing item list documented here. By following the procedures in the symbolic FRUs listed here you will isolate to the correct FRU list based on system model and features installed. 6902 Bus Expansion Adapter card failed An optical bus has failed due to an internal chip error on one of the remote bus adapters. Perform BUS-PIP1.

Failing Item LPARSUP

FI00065 AJDG301

LBUSADP AJDG301

FI00203 AJDG301
Reference Code 6905 Description/Action Perform all actions before exchanging Failing Items Optical bus failed An optical bus is inoperative due to a stuck line or an invalid bus command. Any bus-related hardware may have failed. Perform BUS-PIP1. For this reference code the failing item list presented in the Service Action Log can be different from the failing item list documented here. That is due to the differences in system models and features installed. If the Service Action Log is available then use the failing item list presented there for servicing this reference code. If the Service Action Log is not available then use the failing item list documented here. By following the procedures in the symbolic FRUs listed here you will isolate to the correct FRU list based on system model and features installed. 6906 High Speed Link (HSL) I/O bridge failure LIC could not access part of the HSL I/O bridge VPD. The bridge and HSL loop may be prevented from becoming operational. For this reference code the failing item list presented in the Service Action Log can be different from the failing item list documented here. That is due to the differences in system models and features installed. If the Service Action Log is available then use the failing item list presented there for servicing this reference code. If the Service Action Log is not available then use the failing item list documented here. By following the procedures in the symbolic FRUs listed here you will isolate to the correct FRU list based on system model and features installed. NOTE: A fiber optic cleaning kit may be required for optical HSL connections. 6907 High Speed Link (HSL) I/O bridge failure LIC detected invalid data in the HSL I/O bridge VPD. The bridge and HSL loop may not have become operational. For this reference code the failing item list presented in the Service Action Log can be different from the failing item list documented here. That is due to the differences in system models and features installed. If the Service Action Log is available then use the failing item list presented there for servicing this reference code. If the Service Action Log is not available then use the failing item list documented here. By following the procedures in the symbolic FRUs listed here you will isolate to the correct FRU list based on system model and features installed. NOTE: A fiber optic cleaning kit may be required for optical HSL connections. SIIOADP OPT_CLN SIIOADP OPT_CLN Failing Item FI00065 LBUSADP AJDG301