FLX TM Self-Regulating Heating Cable
for Winterization/Freeze Protection

Design Guide

Commercial Products

Contents

Introduction.... 2 Application Information... 2 Product Description Characteristics Freeze Protection Design Outline.. 3 Basis for a Good Design Step 1: Establish Design Parameters.. 3 Step 2: Select the Proper FLX Heating Cable. 4-5 Step 3: Determine FLX Circuit Lengths. 6 Step 4: Choose FLX Cable Options.. 7 Step 5: Choose FLX Installation Accessories.. 8.
Design Worksheet.. 9 Design Tips... 10 General Specification...11 Product Approvals and Tests.. 12
For additional information about freeze protection of piping with heat tracing, please review the FLX product specification sheet (Thermon Form CPD1007) and the systems accessories sheet (Thermon Form CPD1017). Contact Thermon for additional information.

Introduction.

While an insulated pipe can withstand cold temperatures longer than an uninsulated pipe, the contents of the pipe will cool to the temperature of the surrounding environment. When the ambient temperature is below freezing, the results can be both costly and inconvenient. FLX self-regulating heating cable is designed to provide freeze protection of metallic and nonmetallic pipes, tanks and equipment by replacing the heat lost through the thermal insulation into the air. Whether the application is a small project or a complex network of piping and equipment, designing an electric heat-traced freeze protection system is easy with FLX. The information contained in this design guide will take the reader through a step-by-step procedure to make proper heating cable selections based on: Minimum ambient temperature Heating cable start-up temperature Pipe size Thermal insulation type and thickness Available power supply After following the prescribed steps in this design guide, the reader will be able to design, specify or establish a bill of materials for a freeze protection heat tracing system. If higher maintain temperatures are required contact Thermon for additional information.

Product Description.

FLX self-regulating heating cable varies its heat output to compensate for the surrounding conditions along the entire length of a circuit. Whenever the heat loss of the insulated pipe, tank or equipment increases (as ambient temperature drops), the heat output of the cable increases. Conversely, when the heat loss decreases (as ambient temperature rises), the cable reacts by reducing its heat output. This self-regulating feature occurs along the entire length of a heat tracing circuit to ensure each point receives the required amount of heat while conserving energy. FLX heating cables are rated for nominal heat outputs of 3, 5, 8 and 10 watts per foot at 50F (10, 16, 26 and 33 watts per meter at 10C) when powered at 110 to 120 Vac or 208 to 277 Vac. FLX self-regulating cables are protected by a tinned copper braid and a polyolefin outer jacket to provide grounding and additional mechanical protection for the cable. An optional fluoropolymer outer jacket is available if additional environmental protection is required.

Characteristics.

Bus wire... 16 AWG nickel-plated copper Metallic braid... tinned copper Outer jacket.. -OJ, polyolefin; -FOJ, fluoropolymer Minimum bend radius @ 5F (-15C)...0.38" (10 mm) @ -76F (-60C)....1.25" (32 mm). Supply voltage...110-120 or 208-277 Vac Circuit protection.. 30 mA ground-fault protection required Max. operating temperature (power-on)... 150F (65C) Max. exposure temperature (power-off).. 185F (85C) Minimum installation temperature... -60F (-51C)
Bus Wire Radiation Cross-Linked Heating Core Radiation Cross-Linked Polyolefin Insulation

Tinned Copper Braid

Outer Jacket
Freeze Protection Design Outline.
The following steps outline the design and selection process for an FLX self-regulating freeze protection system: Step 1: Establish Design Parameters Collect relevant project data: a. Piping/equipment Diameter Length Material b. Temperatures Minimum ambient Maintain temperature Start-up temperature c. Insulation Type Thickness d. Electrical Supply voltage Circuit breaker size Step 2: Select the Proper FLX Heating Cable Using information gathered in Step 1: a. For metallic piping, use Design Chart 2.1 b.For nonmetallic piping, use Design Chart 2.2 Step 3: Determine FLX Circuit Lengths Based on: a. Pipe lengths plus allowances for Valves, pumps, other equipment Pipe supports Circuit fabrication and splice kits b. Electrical supply Operating voltage Available branch circuit breaker sizes c. FLX selection parameters Start-up temperature Maximum FLX circuit lengths Step 4: Choose FLX Cable Options Metallic braid and a polyolefin outer jacket are standard; options include: a. Fluoropolymer outer jacket b. Monitor wire Step 5: Choose FLX Installation Accessories Minimum accessories include: a. Circuit fabrication kit b. Attachment tape The step-by-step procedures which follow will provide the reader with the detailed information required to design, select and/or specify a fully functional electric heat tracing system. 3

Basis for a Good Design.

The generally accepted maintenance temperature for freeze protection is 40F. This design guide is based on that 40F temperature and provides a safety zone to protect the piping and the contents from freezing. To become familiar with the requirements of a properly designed electric heat tracing freeze protection system, use the five design steps detailed here and on the following pages. Once comfortable with the steps and the information required, use the design worksheet included at the end of this design guide for applying these steps to a freeze protection heat tracing application. Step 1: Establish Design Parameters Collect information relative to the following design parameters: Application Information. Pipe sizes or tubing diameters Pipe lengths Pipe material (metallic or nonmetallic) Type and number of valves, pumps or other equipment Type and number of pipe supports Expected Minimum Ambient Temperature. Generally, this number is obtained from weather data compiled for an area and is based on recorded historical data. There are times, however, when the minimum ambient will be a number other than the minimum outside air temperature. Piping located inside of unheated buildings or in unconditioned attics may be subject to freezing but may have different minimum ambients. Minimum Start-Up Temperature. This temperature differs from the minimum expected ambient in that the heating cable will typically be energized at a higher ambient temperature. This temperature will have an effect on the maximum circuit length and circuit breaker sizing for a given application (see Table 3.2 or 3.3 on page 6). Insulation Material and Thickness. The selection charts in this design guide are based on fiberglass insulation with thicknesses shown in Design Selection Charts 2.1 and 2.2. If insulation materials other than fiberglass are used, contact a Thermon factory representative for a design selection chart supplement that corresponds with the insulation material. Supply Voltage. FLX self-regulating cables are designed in two voltage groups: 110-120 Vac and 208-277 Vac. Determine what voltage(s) are available at a facility for use with heat tracing.
Step 2: Select the Proper FLX Heating Cable Using the pipe diameter, insulation thickness and minimum expected ambient, find the recommended heating cable using Design Selection Chart 2.1 Metallic Piping, at right, or Design Selection Chart 2.2 Nonmetallic Piping on page 5. All cable selection is based on fiberglass insulation. Closed-cell flexible foam insulation of the same thickness may also be used. If the pipe size or insulation information does not appear, contact Thermon or a Thermon factory representative. 1. Select the vertical column headed by a low ambient temperature which is equal to or lower than that expected. 2. Use the table section which corresponds to the pipe insulation thickness shown in the left-hand column. 3. Based on the pipe diameter(s) for the application, read across the table to the low ambient temperature and note the FLX cable recommended for that set of conditions. 4. Note that larger pipe sizes and lower ambient temperatures may require multiple passes of heating cable. 5. On piping 1-1/4" in diameter and smaller, the insulation must be one pipe size larger to accommodate the heating cable; i.e., use insulation sized for a 1" diameter pipe if the pipe to be insulated is 3/4" diameter. 6. For pipe sizes larger than listed or for maintain temperatures other than 40F (4C), contact Thermon or a Thermon factory representative.

One Pass 3-FLX One Pass 5-FLX One Pass 8-FLX One Pass 10-FLX Contact Thermon
Design Selection Chart 2.1 Metallic Piping
Insulation Thickness NPS Pipe Size 1/2" 3/4" 1" 1-1/4" 1/2" 1-1/2" 2" 2-1/2" 3" 4" 6" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 1" 3" 4" 6" 8" 10" 12" 14" 1" 1-1/4" 1-1/2" 2" 2-1/2" 1-1/2" 3" 4" 6" 8" 10" 12" 14" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 2" 4" 6" 8" 10" 12" 14" 16" - 20" +10F (-12C) Low Ambient Temperature 0F -10F -20F (-18C) (-23C) (-29C) -40F (-40C)
Design Selection Chart 2.2 Nonmetallic Piping
Insulation Thickness NPS Pipe Size 1/2" 3/4" 1" 1-1/4" 1/2" 1-1/2" 2" 2-1/2" 3" 4" 6" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 1" 3" 4" 6" 8" 10" 12" 14" 1" 1-1/4" 1-1/2" 2" 2-1/2" 1-1/2" 3" 4" 6" 8" 10" 12" 14" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 2" 4" 6" 8" 10" 12" 14" 16" - 20"
Note. Heat loss calculations are based on IEEE Std 515, Equation A.1, with the following provisions: Piping insulated with glass fiber in accordance with ASTM Std C547. Pipes located outdoors in a 0F ambient with a 25 mph wind. A 10% safety factor has been included.

+10F (-12C)

Low Ambient Temperature 0F -10F -20F (-18C) (-23C) (-29C)

-40F (-40C)

Additional Considerations for Nonmetallic Piping. For freeze protecting nonmetallic pipes, FLX is to be installed with a continuous covering of AL-20L foil tape. The data in Design Selection Chart 2.2 is based on this installation method. Heat loss characteristics are similar to metal pipes, but the FLX self-regulating cable output is lower because of the insulating properties of the pipewall material. Design Selection Chart 2.2 reflects these values.
Step 3: Determine FLX Circuit Lengths Heat tracing circuit lengths are based on several conditions which must be simultaneously taken into account and include: Length of piping (including extra allowances) Operating voltage Available branch circuit breaker sizes Expected start-up temperature Maximum allowable circuit lengths Every heat tracing circuit will require some additional heating cable to make the various splices and terminations. Additional cable will also be needed to provide extra heat at valves, pumps, miscellaneous equipment and pipe supports. Use the following guidelines to determine the amount of extra cable required: Power connections. Allow an additional 1' of FLX cable for each heating circuit. In-line splices. Allow an additional 2' of FLX cable for each splice kit. T-splices. Allow an additional 3' of FLX cable for each splice kit. Pipe supports. Insulated pipe supports require no additional heating cable. For uninsulated supports, allow two times the length of the pipe support plus an additional 15" of heating cable. Valves and pumps. Use allowances from Table 3.1. To determine circuit lengths, a voltage selection must be made from the available voltages gathered as part of Step 1. FLX intended for use on 110-120 Vac will have a catalog number followed by a 1; i.e., 5-FLX-1. FLX intended for use on 208-277 Vac will have a catalog number followed by a 2; i.e., 5-FLX-2. In Step 2 the proper FLX cable (3, 5, 8 or 10) was selected from Design Selection Chart 2.1 or 2.2. Using voltage and cable selections plus Table 3.2 or 3.3 the maximum heating cable lengths and branch circuit breaker requirements can be determined. If a branch circuit breaker of a known amperage will be used, match this rating with the cable selection and the temperature at which the cable will be energized. If no circuit breaker sizing has been established, find the maximum circuit length that meets or exceeds the length of the appropriate FLX cable at the start-up temperature of the cable and determine what amperage branch circuit breaker will be required. Remember the start-up temperature does not necessarily match the expected low ambient. Table 3.1 Valve and Pump Allowances

Pipe Size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 3" 4" 6" 8" 10" 12" 14" Screwed 6" 9" 1' 1' 6" 1' 6" 2' 2' 6" 4' 7' 9' 6" 12' 6" 15' 18' Valve Allowance Flanged Butterfly 1' 1' 6" 2' 2' 2' 6" 2' 6" 3' 6" 5' 8' 11' 14' 16' 6" 19' 6" 1' 1' 1' 6" 2' 2' 6" 3' 3' 6" 4' 4' 5' 5' 6" Pump Allowance Screwed Flanged 1' 1' 6" 2' 3' 3' 4' 5' 8' 14' 19' 25' 30' 36' 2' 3' 4' 4' 6" 5 5' 6 7' 10' 16' 22' 28' 33' 39'

Table 3.2 110-120 Vac

120 Vac Service Voltage Catalog Number 3-FLX-1 5-FLX-1 8-FLX-1 10-FLX-1 Start-Up Temperature F (C) 0 (-18) 50 (10) 0 (-18) 50 (10) 0 (-18) 50 (10) 0 (-18) 50 (10) Max. Circuit Length 3 vs. Breaker Size ft (m) 20A 324 (98.0) 377 (114.0) 207 (63.1) 239 (72.8) 150 (45.7) 191 (58.2) 112 (34.1) 159 (48.5) 30A 348 (106.0) 377 (114.4) 299 (91.1) 299 (91.1) 226 (68.9) 239 (72.8) 169 (51.5) 199 (60.7) 40A 348 (106.0) 377 (114.0) 299 (91.1) 299 (91.1) 239 (72.8) 239 (72.8) 199 (60.7) 199 (60.7)

Table 3.3 208-277 Vac

208-277 Vac Service Voltage Catalog Number 3-FLX-2 5-FLX-2 8-FLX-2 10-FLX-2 Start-Up Temperature F (C) 0 (-18) 50 (10) 0 (-18) 50 (10) 0 (-18) 50 (10) 0 (-18) 50 (10) Max. Circuit Length 3 vs. Breaker Size ft (m) 20A 649 (197.0) 737 (224.0) 393 (119.8) 479 (146.0) 284 (86.6) 383 (116.7) 225 (68.6) 280 (85.3) 30A 712 (217.0) 737 (224.0) 590 (179.8) 599 (182.6) 427 (130.1) 479 (146.0) 338 (103.0) 399 (121.6) 40A 712 (217.0) 737 (224.0) 590 (179.8) 599 (182.6) 479 (146.0) 479 (146.0) 399 (121.6) 399 (121.6)
Step 4: Choose FLX Cable Options To ensure that the proper FLX heating cable is purchased, some additional cable choices must be made. All FLX self-regulating cables include a tinned copper braid and polyolefin outer jacket as standard equipment. This outer jacket, designated by an OJ suffix added to the cables catalog nomenclature (i.e., 5-FLX-1 OJ), provides additional mechanical protection for the cable. Additional environmental barriers are available to provide corrosion protection for the tinned copper braid in locations subject to hydrocarbon-based chemical solutions. Fluoropolymer outer jacket. for organic chemicals or corrosives (an FOJ suffix is added to the FLX catalog number; i.e., 5-FLX-1-FOJ). Nomenclature for Ordering. Following is an example of a typical catalog number for FLX:
X-FLX-X-XXXX Denotes nominal thermal output at 50F Indicates voltage rating: -1 indicates 110-120 Vac -2 indicates 208-277 Vac Indicates additional cable options: OJ =Polyolefin outer jacket (standard) FOJ= Fluoropolymer outer jacket (includes tinned copper braid) Example. From the information obtained in Steps 1, 2 and 3, suppose an 8-FLX-1 heating cable will be required for a project. Since the application will have exposure to sea air, a standard polyolefin outer jacket is desired. The proper FLX cable for this application is: 8-FLX-1-OJ.

Step 5: Choose FLX Installation Accessories An FLX self-regulating freeze protection heat tracing system will typically include the following components: 1. FLX self-regulating heating cable (refer to Design Selection Charts 2.1 and 2.2 for proper cable). 2. PCA-COM circuit fabrication kit (shown with optional JB-6 junction box). 3. PCS-COM in-line/T-splice kit (permits two or three cables to be spliced together). 4. ET-6 (for OJ cable) cable end termination. Each PCA-COM and PCS-COM includes one ET-6 end cap. 5. FT-1L attachment tape (3/4" x 180' attachment tape secures cable to pipe; use on 12" intervals or as required by code or specification). Use Table 5.1 FT-1L Attachment Tape Allowance to determine tape requirements. 6. CL Electric Heat Tracing label (peel-and-stick label attaches to insulation vapor barrier on 10' intervals or as required by code or specification). 7. Fiberglass thermal insulation and vapor barrier (by others). As a minimum, each FLX heat tracing circuit requires a PCA-COM circuit fabrication kit and FT-1L cable attachment tape. Use Table 5.1 to calculate the number of rolls of FT-1L attachment tape required based on the pipe diameter(s) and total length of heating cable required. Table 5.1 FT-1L Attachment Tape Allowance Fixing Tape Allowance (Feet of Pipe Per Roll of Tape)
Tape Length 108' Roll 180' Roll Pipe Diameter in Inches "-1" 130' 215' 1" 115' 195' 1" 110' 180' 2" 95' 160' 3" 75' 125' 4" 65' 105' 6" 50' 80' 8" 40' 65' 10" 35' 55' 12" 30' 50' 14" 26' 43' 16" 23' 38' 18" 21' 35' 20" 19' 31' 24" 16' 27' 30" 13' 22'
For nonmetallic piping applications requiring AL-20L aluminum tape, plan for one foot of tape for each foot of heating cable. AL-20L is available in 2" x 150' rolls.
Notes. All heat-traced lines must be thermally insulated. Circuit fabrication kits do not include electrical junction boxes. Thermostatic control (not shown) is recommended for all freeze protection and temperature maintenance heat tracing applications (see page 10). 30 mA ground-fault equipment protection is to be used for all heat tracing circuits.

Design WORKSHEET

Once the information relating to the design parameters has been obtained and the design steps have been followed, an FLX heat tracing bill of materials may be generated using this worksheet. Step 1: Establish Design Parameters Collect information for each pipe/heat tracing circuit relative to the following design parameters: Application Information. Piping: Metallic vs. Nonmetallic Length Diameter Step 2: Select the Proper FLX Heating Cable Using the information gathered in Step 1, refer to Design Selection Chart 2.1 (for metallic piping) or Design Selection Chart 2.2 (for nonmetallic piping). Remember to select the proper FLX self-regulating cable based on the minimum ambient temperature expected. Step 3: Determine FLX Circuit Lengths Use Table 3.2 (110-120 Vac) or Table 3.3 (208-277 Vac) to determine the maximum circuit length based on the circuit breaker size and start-up temperature. Record the information below: FLX Cable Voltage Vac Start-Up Temperature Ckt. Brkr. Size Max. Ckt. Length

EquipmentType and Number of: Valves Pumps

Misc. Equip.

Pipe Supports: Type/Length

Number

Step 4: Choose FLX Cable Options Determine the proper FLX cable options required to meet the installation. All FLX is equipped with a standard tinned copper braid and polyolefin outer jacket. Check the other options required: OJ Polyolefin outer jacket (standard)
Expected Temperatures. Minimum ambient Minimum start-up temp. Maintain temperature Insulation Thickness. Assumed Fiberglass: Pipe Diameter Insul. Thick. Nom. Insul. Size
FOJ Fluoropolymer outer jacket
Step 5: Choose FLX Installation Accessories PCA-COM circuit fabrication kit PCS-COM in-line/T-splice kit FT-1L attachment tape AL-20L aluminum tape (for nonmetallic piping) CL Electric Heat Tracing label B4X-15140 adjustable ambient sensing thermostat E4X-1-SR adjustable pipewall sensing thermostat JB-6 junction box
Electrical Information. Supply voltage Circuit breaker size

Design Tips.

To ensure a properly operating heat tracing system and avoid the common mistakes made by first-time users, the following tips have been compiled: 1. When a heat-traced pipe enters a facility, the heating cable should extend into the building approximately 12" (305 mm) to ensure the pipe temperature is maintained. This prevents temperature drops due to air gaps or compression of the thermal insulation. 2. A similar situation exists when an aboveground pipe goes underground. While the pipe may eventually travel below the frost line and therefore be protected from freezing, the distance between the surface (grade) and the frost line must be protected. This can be accomplished by creating a loop with the heating cable end terminated above the normal water line. If the application is temperature maintenance, the above grade and below grade portions should be controlled as separate circuits due to the differing surrounding environments. 3. Where a freeze protection application has a main line with a short branch line connected to it, the heating cable installed on the main line can be looped (double passed) on the branch line. This eliminates the need to install a T-splice kit. 4. All of the heating cable power connection points should be secured to the piping. Heating cable should not pass through the air to travel to an adjoining pipe. Instead, use multiple circuit fabrication kits interconnected with conduit and field wiring as shown.

Thermostatic Control.

While the five steps in the design and selection process provide the detailed information required to design, select and/or specify an FLX self-regulating heat tracing system, some type of control will typically be needed. The type of control and level of sophistication needed will depend entirely on the application of the piping being heat-traced. Self-regulating heating cables can, under many design conditions, be operated without the use of any temperature control; however, some method of control is generally used and the two most common methods are ambient sensing and pipewall sensing. Each method has its own benefits, and various options are available within each method. Ambient Sensing. An adjustable thermostat, designed for mounting in an exposed environment, senses the outside air temperature. When this temperature falls below the set point, a set of contacts close and energize the heating cable(s). Should the electrical load of the heating circuit exceed the rating of the thermostat switch, a mechanical contactor can be used. An entire power distribution panel, feeding dozens of heat tracing circuits, can be energized through an ambient sensing thermostat. The primary application for ambient sensing control of electric heat tracing is freeze protection (winterization) of water and water-based solutions. A benefit of ambient sensing control for freeze protection is that pipes of varying diameters and insulation thicknesses can be controlled as a single circuit. By controlling heat tracing with ambient sensing control, the status (flowing or nonflowing) of the heated pipe needs no consideration. Pipewall Sensing. While a self-regulating cable adjusts its heat output to accommodate the surrounding conditions, the most energy-efficient method for controlling heat tracing is a pipewall sensing thermostat. This is because a flowing pipe will typically not need any additional heat to keep it at the proper temperature. Where a piping system has tees and therefore multiple flow paths, more than one thermostat may be required. Situations where more than one thermostat could be necessary include: Pipes of varying diameters or insulation thicknesses. Varying ambient conditions such as above/below ground transitions and indoor/outdoor transitions. Flowing versus nonflowing conditions within the interconnected piping. Applications involving temperature-sensitive products.

General Specification

Part 1. General Furnish and install a complete UL Listed system of heaters and components approved specifically for pipe heat tracing. The heat tracing system shall conform to ANSI/IEEE Standard 515.1. Part 2. Products 1. The self-regulating heater shall consist of two nickel-plated copper bus wires embedded in a radiation cross-linked semiconductive polymer core. The heater shall be capable of varying its heat output along its entire length, allowing the heater to cross over itself without overheating. The heater shall be covered by a polyolefin dielectric jacket rated 300 Vac at 105C and a tinned copper braid (12 AWG equivalent wire size). 2. In addition to a tinned copper braid, the heating cable shall be covered by (select): a. A polyolefin outer jacket for protection from aqueous inorganic chemicals (standard construction). b. A fluoropolymer outer jacket for protection from organic chemicals or corrosives (optional). 3. The heater shall operate on a line voltage of (select 110-120 or 208-277) Vac without the use of transformers. 4. The heating cable shall be suitable for use on metallic and nonmetallic piping. On nonmetallic piping, the cable shall be attached to the pipe with a parallel covering of aluminum tape. 5. For additional energy conservation, the heating cable shall be controlled by (select): a. An adjustable ambient sensing thermostat with a switch rating of 22 amps. b. A bimetallic pipewall sensing thermostat preset at 40F with a switch rating of 22 amps at 120/240/277 Vac based on current loads for each circuit. c. An adjustable pipewall sensing thermostat with a switch rating of 30/25 amps at 240/277 Vac. d. Where the load of the heating cable exceeds the rating of the thermostat, the heating cable shall be controlled through an appropriately sized contactor by the control thermostat. 6. All heating cable core will be permanently marked with the manufacturers identification number for traceability. 7. Acceptable products and manufacturers: FLXTM cable and accessories as manufactured by Thermon. 8. Refer to the manufacturers freeze protection design guide for design details, insulation requirements, maximum circuit lengths and accessory information. Part 3. Manufacturer 1. Manufacturer shall demonstrate experience manufacturing and designing freeze protection systems with self-regulating heating cables. This experience may be documented with a list of___ projects utilizing at least 2,000 feet (600 meters) of self-regulating heating cable. 2. Manufacturers Quality Assurance Program shall be certified to the ISO 9001 Standard. Part 4. Installation 1. Refer to the manufacturers installation instructions and design guide for proper installation and layout methods. Deviations from these instructions could result in performance characteristics different than intended. 2. All installations and terminations must conform to the National Electrical Code and any other applicable national or local code requirements. 3. Circuit breakers supplying power to the heat tracing shall be equipped with 30 mA ground-fault equipment protection; 5 mA GFCI should not be used as nuisance tripping may result. 4. Piping shall be pressure tested prior to installation of heating cable. Thermal insulation shall not be installed until heating cable installation is complete and a megohmeter (megger) test has been passed (see Testing, Part 5). Heattraced lines shall be insulated promptly after the heat tracing installation. 5. The insulation shall not be installed with staples. Insulation jackets should be closed with adhesive to avoid damage to the heating cable. 6. System shall be connected to power by the electrician (see Division 16-Electrical). Part 5. Testing 1. Heating cable shall be tested with a megohmeter (megger) between the heating cable bus wires and the metallic ground braid. While a 2,500 Vdc megger test is recommended, the minimum acceptable level for testing is 500 Vdc. This test should be performed a minimum of three times: a. Prior to installation while the cable is still on reel(s). b. After installation of heating cable and completion of circuit fabrication kits (including any splice kits) but prior to installation of thermal insulation. c. After installation of thermal insulation but prior to connection to power. 2. The minimum acceptable level for the megger readings is 20 megohms, regardless of the circuit length. 3. Results of the megger readings shall be recorded and submitted to the construction manager. 11

Product Approvals and Tests.
Thermons FLX carries the following major agency approvals: Underwriters Laboratories Inc.: FLX cables and accessories are UL Listed for heating pipes and related equipment (Pipe Heating Cable 134N). Canadian Standards Association: FLX cables and accessories are CSA certified for the intended application. Other approvals for FLX heating cables and accessories are also in place. Contact Thermon for additional information. FLX Cables Meet or Exceed the Following Tests. Test

Standard Followed

Abrasion Resistance..UL 1588 (8.3); IEEE 515.1 (4.3.4) Elevated Temperature. IEEE 515.1 (4.2.5) Deformation.. IEEE 515.1 (4.2.8) Dielectric Withstand.. IEEE 515.1 (4.2.1) Resistance to Impact.. UL 1588 (8.2). Resistance to Cutting.. IEEE 515.1 (4.3.3) Resistance to Crushing. UL 1588 (8.1) Temperature.. UL 1588 (9.1-9.3) Vertical Flame.. UL 1588 (8.5) Thermal Stability.. Thermon OP 7.24 Self-Regulating Index.. Thermon OP 7.94
THERMON. The Heat Tracing Specialists 100 Thermon Dr. PO Box 609 San Marcos, TX 78667-0609 Phone: (512) 396-5801 Facsimile: (512) 754-2431 1-800-730-HEAT www.thermon.com In Canada call 1-800-563-8461

Form CPD1008-0710

Thermon Manufacturing Co.

Printed in U.S.A.