COMBOS AND MECHANICAL INSTRUMENTS

USERS GUIDE

Combo Consoles Console Compasses CB-71 and CB-71/DS Depth Gauge SM-16 Pressure Gauge SM-26 and SM-36

SUUNTO

General Instructions
Suunto diving instruments are constructed of high quality materials and are designed for normal recreational use. The product should provide many years of reliable service if the user observes the necessary precautions in the following directions.
SUUNTO Combo Consoles Introduction
The Suunto combo consoles allows you to create a personal combo according to your own specic needs. Analogue gauges, dive computers and compasses t together like building blocks, giving the possibility to add as many instruments as you like. The Suunto Combo modules and instruments can be combined in an almost innite amount of combinations, and allow you to change or upgrade your combo conguration. The new combos consist of four main modules: the pressure gauge module, the instrument module and two different compass modules. The pressure gauge module is designed for the Suunto pressure gauges and it can also be used with the new Suunto Quick Release (QR). The instrument module can be tted with Suunto dive computers or with the newly designed Suunto analog depth gauges. Depending on the users choice, an SK-7 compass module can either be tted on the back side of the pressure gauge module or on top of the pressure gauge or instrument module. The basic combinations are displayed below:
Assembling the Combo Modules
The Combo modules are to be assembled in the order described by the illustration below:
1. CB-One module front cover with SM-26/36 pressure gauge in place (see section CB-ONE Module assembly) 2. CB-In line module front cover 3. CB-end piece or CB-71 compass (optional) 4. CB-In line module back cover with instrument 5. CB-One module back cover or CB-71/DS compass (optional)

CB-ONE Module Assembly

The CB-ONE Module is designed to t the Suunto SM-26/36 analog pressure gauges. Before assembling the CB-ONE module the hose cover needs to be tted on the pressure hose. The hose cover ensures that the SM-26/36 pressure gauge ts properly on the CB-ONE module.
If the Suunto Quick Release is used, the hose cover is not to be used (See section CB-ONE module assembly using the SUUNTO Quick Release). After attaching the hose cover the pressure hose and gauge are assembled on the CB-ONE front cover according to the picture.
After the pressure gauge is in place the CB-ONE back cover (or alternatively the CB-71/SK-7/DS compass) is attached with four screws.
CB-ONE Module Assembly when using the SUUNTO Quick Release
If the SUUNTO Quick Release (QR) is used the hose cover should be attached on the high pressure hose below the female end of the QR. The male part is attached to the pressure gauge which is then tted onto the CB-ONE front cover according to the picture below.
CB-IN-LINE Module Assembly
The CB-IN-LINE module ts the Suunto Vyper, Gekko, Solution, Favor/Fusion, Octopus II and Companion dive computers or the SM-16 round depth gauge. The Vyper locks in place on the IN-LINE module back cover. For the other instruments there are lugs on the back cover aiding the orientation.
The Solution, Favor and Companion can be tted with display shield V5615. The display shield is attached after the console has been assembled by bending the console so that the shield ts between the computer and the console cover. The Vyper is delivered with a pre-attached display shield (V5875).
SUUNTO Console Compasses CB-71/SK-7/STD and CB-71/SK-7/DS
The high-quality, liquid-lled Suunto diving compasses are durable, reliable and easy to use. The CB-71/SK-7 is available in two versions: the CB-71/SK-7/STD for attachment on top of the combo modules or the Cobra dive computer, and the CB-71/SK-7/DS for attachment on the back side of the CB-ONE module.

Compass use for divers

General instructions Usually a compass must be held precisely in a horizontal position, otherwise the needle will sting. The SK-7 compass may however be inclined about 30 degrees. Sighting a compass bearing Hold the compass so that the compass is in a horizontal position and the direction line points away from you. Turn with the compass until the direction line points at your destination, then turn the direction ring until the magnetic North needle is aligned between the slit marks. The front end of the direction line on the SK-7 shows your compass bearing, and as long as the North needle is aligned between the slit marks, the direction points toward your destination. The SK-7 compasses also have a side reading window, which also enables you to take a bearing by directing the compass towards the destination and by reading the compass bearing from the side window. This bearing can be memorized by turning the direction ring to that bearing. Setting a given bearing or direction The scale division on the SK-7 is 360 degrees clockwise from 0 degrees at North. Turn the direction ring until the front end of the direction line is at the desired direction. Turn the compass until the needle falls between the slit marks. The direction line now points in the desired direction. Magnetic declination Maps and marine charts are drawn in correlation to the geographic poles, while the magnetic compass needle is subject to magnetic declination which varies according to the location. General orientation on the diving site Before diving, check the main compass bearings at the dive site, paying special attention to memorizing the direction of the shoreline and bearings of landmarks that may be of importance. Natural aids to underwater navigation The underwater extension of the shores inclination tells the diver if he is following the shoreline. Be careful however as underwater ridges may lead you astray. Surface occasionally to check your position. The dip and stratication of rocks on the shore can often be followed over large areas under water Sand ripples usually form long lines parallel to the shore The direction of currents should be noted by their effect on algae or drifting particles. Use the compass to check the bearing of the current

In shallow water, the suns direction can be seen from shadows on the bottom, or by looking towards the surface Swimming in a straight line along the bottom is greatly facilitated if you can line up three distinctive objects in your line of vision. As you reach the rst one, line up a new one farther away, so that you again have three points determining your course. This way you can counteract the effects of side current.

Compass Balancing

The horizontal and vertical components of earths magnetic eld vary considerably in different locations. For this reason Suunto compasses are balanced for 5 different zones. If the compass is used in an adjacent balancing zone the compass needle will tilt only slightly. However, the farther the compass is used from its intended zone, the more the needle will tilt. In extreme situations the needle might stick. For this reason it is very important to know in which country the compass will be used.

Compass zone map

SUUNTO Mechanical Gauges
Suunto depth gauge SM-16 Models available: 45 m, 70 m, 150 ft, 230 ft Suunto pressure gauge SM-26 Models available: 200bar Suunto pressure gauge SM-36 Models available: 300bar and 4000psi

Before usage

Depth gauge: Before diving, check the position of the depth indicating pointer. Atmospheric conditions (altitude, temperature) may cause the point to not indicate zero. If this is the case, turn the adjusting screw located at the right side of the gauge to align the pointer to zero. The adjustment is to be made at the temperature of usage. Repeated unnecessary adjustments may cause excessive wear to the seals and eventual leakage. CAUTION! Do not attempt to adjust the water entry port located at the left side of gauge. Tampering with the port can cause damage to internal components. Do not pressure test gauge in air. Always immerse the gauge in water while pressure testing it. Pressure gauge: The hose has an end tting with 7/UNF-thread. If your regulator has a different thread size in the high pressure (HP-output) port, ask your dealer for the correct adapter. Always inspect the o-ring at the male thread to be sure it is clean and undamaged before connecting it to the regulator. Always turn your air supply on slowly. Always turn the pressure gauge dial face away from your face when turning on the air supply. Do not overtighten the hose at the gauge, the tting is pressure proof even when tightened with ngers.

Service

Avoid subjecting the gauges to excessive shock loads such as those that might occur from being dropped or hit against an immovable object. Do not subject the gauges to pressures beyond their maximum range. Temperature extremes can be damaging. In general, the gauges should not be exposed to temperatures to which you would not expose yourself. After use: Rinse the gauges or the console with fresh water and store them out of direct sunlight, in a dry place at room temperature. CAUTION! Do not attempt to clean the gauges with anything other than water. Use of cleaning agents or compressed air can cause permanent damage. The introduction of any probe into the water entry port of the depth gauge or the pressure relief valve opening of the pressure gauge can also damage internal components.

Before prolonged storage the instruments should be removed from the console, rinsed with fresh water and stored separately.
CAUTION! Do not attempt to disassemble the gauges. Special tools and training are required to perform the adequate service.
The instruments must be serviced by an authorized dealer every second year or after 200 dives (whichever comes rst).
Operating and Storage Temperatures
SM-16 Operating temperature 0 C to 40 C [32 F to 104 F] Storage temperature -20 C to 50 C [-4 F to 122 F] Operating and storage temperature 0 C to 40 C [32 F to 104 F]

SM-26 and SM-36

Technical Specications
The Suunto depth gauge SM-16 complies with the prEN 13319 standard. The tolerances for depth gauges are: At 3m At 6m At 9m At 15m At 30m At 45m At 60m +0.8 / -0.4 m +0.8 / -0.4 m 0.8 m +1/ -1.2 m +1/ -1.2 m +1/ -1.5 m +1 / -1.5 m
The SM-26 and SM-36 pressure gauges comply with the EN 250 standard. The tolerances for pressure gauges, measured at decreasing pressure are: At 40 bar 5 bar At 100 bar 10 bar At 200 bar 10 bar At 300 bar 10 bar
COPYRIGHT This publication and its contents are proprietary to Suunto Oy. Suunto, Wristop Computer, Suunto Combo, Replacing Luck and their logos are registered or unregistered trademarks of Suunto Oy. All rights reserved. While we have taken great care to ensure that information contained in this documentation is both comprehensive and accurate, no warranty of accuracy is expressed or implied. Its content is subject to change at any time without notice.
Printed in Finland 03.2006 / Esa Print Oy / 160329

www.suunto.com

Made in Finland Suunto Oy 11 / 2005, 03 / 2006

Spring Special Offers!

Canary Divers, 184 Burnley Road, Blackburn, BB1 3HW If you dont see it listed then ask! Tel: Website: www.canarydivers.com eMail: info@canarydivers.com
Lots of Special Offers this Spring, with deals to suit all budgets!
Intova IC12 Camera Package - 375
Includes, Camera, Housing, Strobe & arm, Charger, Memory Card, Camera Bag, Care Kit etc
Intova IC12 Camera & Housing - 189
Rugged polycarbonate full function housing Megapixels: 12.0 megapixel sensor HD video mode (720P & VGA) Zoom: 3x Optical/6x Digital LCD: 2.4 inches Memory card: SD (secure digital) up to 16GB Audio: Yes Power: Li-ion rechargeable battery Waterproof housing: Moulded handgrip and action-ease shutter button Depth rating: 54 metres/180 feet Macro focus: Yes
SUUNTO SK7 Compass & Retractor - 65:00
Unclip or extend your SK7 compass while attached to your BCD Nylon coated stainless steel cable Extends up to 25 inches - 60lbs breaking strength Keeps your SK7 quickly to hand, easy to find and secure.
SUUNTO ZOOP Dive Computer - 180:00
Air and Nitrox modes Altitude adjustment Ascent rate monitor / alarm Ascent time display Audible alarm Consumed bottom time graph Battery power indicator Low battery warning
More Great Offers Overleaf..
SPECIAL SUUNTO DIVE COMPUTER DEAL!
We have secured a special offer with Suunto, on a small range of computers when these have gone, then they are gone so if you want one, get in early: Offer 1 Suunto ZOOP SRP 199:00 Canary Divers Offer Price 180:00
Technical Specification: http://www.suunto.com/en/Products/Diving/Suunto-Zoop/
Offer 2 Suunto Vyper SRP 249:00 Canary Divers Offer Price 199:00

Technical Specification:

http://www.suunto.com/en/Products/Diving/Suunto-Vyper/
D1 DrySuit from Waterproof The BEST of the BEST! - 915:00 (100 off RRP for Members)- 815
Seal Armour System the zippered cuff system allows the flexibility to use any mfg's dryglove ring system. Warm Neck Valve Now we have improved our frequently imitated Warm Neck design with the addition of a valve to drain the seal area when you surface. Form Moulded Velcro Tabs For adjusting the Warm Neck Waterproof uses moulded poly-urethane Velcro tabs with Japanese Velcro Plush for maximum hold and good looks. Vented Hood, HAVS. A separated Vented hood fits underneath the warm neck collar. Our exclusive Hood Air Venting System uses one-way valves to vent annoying gas build-up in the hood. The HAVS hood features a 7mm double layered protection in critical heat loss areas and glide skin seals for the neck and face. Because of the shaping of the DRACO, no seams are to be found in the under arm area or in the crotch area, where wrinkling can otherwise cause wearing. The boots are extended in the rear calf area, which facilitates an easy step in. Kevlar reinforced soft boots ensure ultimate strength and flexibility. The Boots are cut on an angle to minimize ankle and calf stress while finning. High Visibility Logo reflective logos on the sleeves and in the neck part. Armoured Dry Zipper. A heavy-duty zippered neoprene cover protects the Dynat dry zipper that is located horizontally over the shoulders. Chill Guard. Under the Dry Zip, it not only keeps body heat in, it also keeps your undergarments out of the zipper for trouble free operation. Two expandable POWER POCKETS on the thighs. Laminated TOUGHTEX nylon coating on the 3,5mm HEIWA Hi-Dense Neoprene. A Seat that Grips Poly-urethane embossing in the back provides a no-slip grip and integrated abrasion protection. Knee Guards Anatomically shaped, 3-Dimensional, injection moulded knee/shin guards provide hard-core protection without compromising comfort and flexibility. Anatomical Sculpting with pre bent arms and legs Draco provides an anatomically sculpted suit designed to fit human movement.
PADI eRDP Multi Level Dive Planner 20:00
Multi-level dive planning Sound can be turned off More robust design Plan up to 5 consecutive dives Plan up to 3 consecutive multi-level dives
Northern Diver 3W Fusion-X Luxeon Torch - 40:00
19 hours burn time Tested to 95 metres depth Aluminium LED housing provides

heat dissipation ensuring maximum LED performance Silicone cover for impact protection Magnetic on/off switch Requires 4 x alkaline AA-cell Duracell batteries (supplied) Supplied complete with lanyard

XS Scuba Drygloves 39.95

XS Scuba Dry Five High Quality Gloves with: - True dry glove construction - 5mm thickness - Reinforced and sealed seams - Twin cuff design for watertight seal with wetsuit Sizes - Small, Medium, Large, XLarge & XX-Large

Glow Sticks 50p each

Ideal for being seen during your night dives Be Seen, Be Safe
GEAR GULPER KIT BOXES LIMITED NUMBER DUE SOON !
Some members had requested that we get hold of some more Gear Gulper Boxes only 30. We have a further supply due soon, so if you want one please reserve yours now!
Tusa Liberator BCD - 272 (Members 259)
Ultimate Stabilizing Harness and Independent
Harness System provide ultimate tank stability and unsurpassed buoyancy control. Stainless steel D-ring on right shoulder strap for accessory attachment. Heavy duty 840 denier nylon shell for superior strength and durability. Advanced weight loading system (A.W.L.S.) with two additional rear trim pockets. 2 large zippered pockets. O.P.E.V. Quick Inflate/Deflate System. Rear quick dump valve. Sizes: XS, S, M, L, XL
W3 Wetsuit from Waterproof
The BEST Wetsuit on the market! 187:00 (159 for Members)
a part of our 25th anniversary collection we wanted something special - and we packed it all into our W3 3,5mm full suit. Even though most brands offer a 3mm suit this does not mean that Waterproof followed the pack. Our fastidious Waterproof customers expect more than just a normal standard suit from us. 3,5mm Semi-Dry Full Suit. Gender Specific Styling. Colours: Mens Blue Ladies - Pink. Microcell CR Neoprene. Front neck zipper. Polyurethane embossing in the back provides a non-slip grip and integrated abrasion protection. Knee Guards PU-embossed. Embossed elbow protection. Wave flex panels in the hollow of arms and legs. Double thread stitch and all ends knotted together. Pre-bent arms and legs for maximum anatomical fit. No four seam crossings. Back zipper with YKK slider. Back zipper with stretch panels. Wave Flex Back Panel. No restraining seam guidance at arms and legs. Open Cell neoprene for an ultimate dry seal under zipper. HexTex inner lining