220/420LTO Tandberg 220/420LTO
Half Height LTO1 and LTO2 Tape Drive

Quick Installation Guide

Revision 4b April 2007

Mechanical Installation

For mechanical mounting specifications, please refer to Figure 1. Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the LEDs up. The drive occupies a half-size 5.25-inch slot with standard holes for mounting screws on both sides of the drive chassis and at the bottom of the drive.

Figure 1

Important! Mounting screw requirements

Mounting specifications

Only M3 (metric) screws must be used for mounting the drive Maximum permitted screw penetration: 2.5 mm Minimum required screw penetration: 2.0 mm Screw torque, mounting screws: 0.5 Nm Screws are supplied with all the Tandberg 220/420LTO drive variants Bags with 4 screws and 4 SCSI ID jumpers are available (Ordering no. 65)
Do not use longer screws or higher screw torque than specified!

Figure 2

Allowed mounting orientations

SCSI Identification

Make sure that the drive unit has the proper SCSI-ID before it is connected to a computer system. Refer to manuals for host computer and application software to obtain the correct ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to Figure 3 and Table 1. External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6).

Power Connector

Service Connector

SCSI Connector

Figure 3 The factory default drive number setting is SCSI ID = 2. If the drive has to be set up with a different unit number, the jumpers (on the Service Connector) have to be connected according to Table 1. Example: SCSI ID = 3

Drive connectors

SCSI ID=0 SCSI ID=1 SCSI ID=2 SCSI ID=3 SCSI ID=4 SCSI ID=5 SCSI ID=6 SCSI ID=7 SCSI ID=8 SCSI ID=9 SCSI ID=10 SCSI ID=11 SCSI ID=12 SCSI ID=13 SCSI ID=14 SCSI ID=15
Table 1 Service Connector jumper settings for SCSI ID (Dark = Jumper mounted) 3

SCSI Cable

Host Internal Terminator Connector Last SCSI Device SCSI-bus 10 cm

Figure 4

SCSI cable (Ordering no. 51) (Ordering no. 53) (Ordering no. 17) (Ordering no. 64)
Internal SCSI-LVD/SE-cable with 5 connectors Internal, removable SCSI-LVD/SE-terminator External, removable SCSI-LVD/SE-terminator External SCSI 68HD/VHDCI 320MBs-cable

Termination

The SCSI-bus cable must be terminated in both ends according to SCSI specifications. If the tape drive is the last device on the bus, the bus must be terminated within 10 cm of the tape drive connection. Tandberg 220/420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98 Specification specifies that the termination of the SCSI-bus system is a part of the SCSI-cable and not a part of the SCSI-device. As a result, termination cannot be turned on or off directly on the tape drive itself. For internal devices, a SCSI-cable with an integrated terminator or a separate terminator applied to the end connector of the cable, 10 cm from the last device, must be used. External devices must be terminated with an external terminator on the last device on the SCSI-bus.

Software Installation

For Software Application support and software drivers, please see www.tandberg.com. Then select SUPPORT and Select Product. For installation of Backup Application software, refer to the software vendors software application user guide supplied with the software or on the software vendors web.

Front LED Indicators

Figure 5
Light Emitting Diodes (LED)

Drive State

READY LED (Green left)

ACTIVITY LED (Green)

CLEAN LED (Amber)

FAULT LED (Amber right)

LED-test. The LEDs are turned ON one-by-one. Power-On Self-Test starts in parallel with the LED-test. Cartridge not loaded. Cartridge loaded, no activity Cartridge loaded, activity Cleaning Cartridge loading or unloading Unrecoverable drive failure Over temperature Media Error (wrong, write protected or harmed media)
OFF ON ON OFF OFF ON / OFF OFF OFF
OFF OFF Flashing Flashing Flashing OFF OFF Flashing
ON / OFF ON / OFF ON / OFF ON ON / OFF ON / OFF ON / OFF ON / OFF
OFF OFF OFF OFF OFF Flashing ON Flashing

Table 2

Front LED behavior during normal operation

Media and Capacities

To achieve and maintain the maximum quality of your Tandberg Data tape drive, we recommend using Tandberg Data media.

Drive Model Tandberg 220LTO Tandberg 420LTO LTO1, 2, 3 Media Name Tape Length 609 m 609 m 609 m Capacity (Native) 100 GByte 200 GByte 100 GByte Ordering no. 26 31
LTO Ultrium Generation 1 (Native format) LTO Ultrium Generation 2 (Native format) LTO Ultrium Generation 1 (Read/Write compatible) Cleaning Cartridge for LTO1, LTO2 and LTO3

Table 3

Media alternatives
External Tabletop Enclosure
ON/OFF Switch Cooling Fan SCSI_ID Switch
SCSI Interface Connectors

Figure 6

External tabletop enclosure, rear side

Power Requirements

Tandberg 220/420LTO in external tabletop enclosure: AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz Tandberg 220/420LTO as standalone: DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A

Heat Dissipation

Tandberg 220/420LTO as standalone: Operating: 18 W Sleep mode with cartridge inserted: 9 W 6
Total customer satisfaction is of the utmost importance to Tandberg Data.
We guarantee that this product left our premises defect free. If you are not satisfied with the quality of this product, please contact your distributor or the nearest Tandberg Data office to have the problem solved! For more documentation and information, please see our website www.tandberg.com.

Tandberg Data

International headquarter
Tandberg Data ASA, Kjelssveien 161, Oslo, P.O. Box 134 Kjelss, N-0411 Oslo, Norway. Tel: +90. Fax: +50. www.tandberg.com

Worldwide subsidiaries

Tandberg Data Corp., 2108 55th Street, Boulder, CO 80301, USA Tel. Toll Free: +1 800-392-2983. Tel. Local: (303) 442-4333 Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany. Tel: +5436 0. Fax: +5436 111. Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vlizy Cedex, France. Tel: +01 01/00800-82632374. Fax: +(for technical support: 00800-07867243). Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914, Tel: +0786. Fax: +0787. Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome, Chuo-ku Tokyo 104-033, Japan Tel: +5566 2871. Fax: +5566 2875. Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury, Oxfordshire, OX15 4FF, United Kingdom Tel: +44 (0) 8450706916.
Specifications subject to change without notice. All trademarks are the property of their respective owners. 2006 Tandberg Data ASA. All Rights reserved. Part No. 433261-04. February 2006.

Tandberg 220/420LTO

Half Height LTO1 and LTO2 Tape Drive

Quick Installation Guide

Revision 4 February 2006

Mechanical Installation

For mechanical mounting specifications, please refer to Figure 1. Allowed mounting position is either horizontal with the indicator LEDs to the right, or vertical with the LEDs up. The drive occupies a half-size 5.25-inch slot with standard holes for mounting screws on both sides of the drive chassis and at the bottom of the drive.

Figure 1

Important! Mounting screw requirements

Mounting specifications

Only M3 (metric) screws must be used for mounting the drive Maximum permitted screw penetration: 2.5 mm Minimum required screw penetration: 2.0 mm Screw torque, mounting screws: 0.5 Nm Screws are supplied with all the Tandberg 220/420LTO drive variants Bags with 4 screws and 4 SCSI ID jumpers are available (Ordering no. 65)
Do not use longer screws or higher screw torque than specified!

Figure 2

Allowed mounting orientations

SCSI Identification

Make sure that the drive unit has the proper SCSI-ID before it is connected to a computer system. Refer to manuals for host computer and application software to obtain the correct ID. For correct mounting of ID-jumpers at the rear of the drive, please refer to Figure 3 and Table 1. External drives have a thumb-wheel switch to set the SCSI-ID (see Figure 6).

Power Connector

Service Connector

SCSI Connector

Figure 3 The factory default drive number setting is SCSI ID = 2. If the drive has to be set up with a different unit number, the jumpers (on the Service Connector) have to be connected according to Table 1. Example: SCSI ID = 3

Drive connectors

SCSI ID=0 SCSI ID=1 SCSI ID=2 SCSI ID=3 SCSI ID=4 SCSI ID=5 SCSI ID=6 SCSI ID=7 SCSI ID=8 SCSI ID=9 SCSI ID=10 SCSI ID=11 SCSI ID=12 SCSI ID=13 SCSI ID=14 SCSI ID=15
Table 1 Service Connector jumper settings for SCSI ID (Dark = Jumper mounted) 3

SCSI Cable

Host SCSI-bus Internal Terminator Connector Last SCSI Device 10 cm

Figure 4

SCSI cable (Ordering no. 51) (Ordering no. 53) (Ordering no. 17) (Ordering no. 64)
Internal SCSI-LVD/SE-cable with 5 connectors Internal, removable SCSI-LVD/SE-terminator External, removable SCSI-LVD/SE-terminator External SCSI 68HD/VHDCI 320MBs-cable

Termination

The SCSI-bus cable must be terminated in both ends according to SCSI specifications. If the tape drive is the last device on the bus, the bus must be terminated within 10 cm of the tape drive connection. Tandberg 220/420LTO has a combined SCSI-LVD/SE interface embedded. The PC-98 Specification specifies that the termination of the SCSI-bus system is a part of the SCSI-cable and not a part of the SCSI-device. As a result, termination cannot be turned on or off directly on the tape drive itself. For internal devices, a SCSI-cable with an integrated terminator or a separate terminator applied to the end connector of the cable, 10 cm from the last device, must be used. External devices must be terminated with an external terminator on the last device on the SCSI-bus.

Software Installation

For Software Application support and software drivers, please see www.tandberg.com. Then select SUPPORT and Select Product. For installation of Backup Application software, refer to the software vendors software application user guide supplied with the software or on the software vendors web.

Front LED Indicators

Figure 5
Light Emitting Diodes (LED)

Drive State

READY LED (Green left)

ACTIVITY LED (Green)

CLEAN LED (Amber)

FAULT LED (Amber right)

LED-test. The LEDs are turned ON one-by-one. Power-On Self-Test starts in parallel with the LED-test. Cartridge not loaded. Cartridge loaded, no activity Cartridge loaded, activity Cleaning Cartridge loading or unloading Unrecoverable drive failure Over temperature Media Error (wrong, write protected or harmed media)
OFF ON ON OFF OFF ON / OFF OFF OFF

OFF OFF Flashing Flashing Flashing OFF OFF Flashing
ON / OFF ON / OFF ON / OFF ON ON / OFF ON / OFF ON / OFF ON / OFF
OFF OFF OFF OFF OFF Flashing ON Flashing

Table 2

Front LED behavior during normal operation

Media and Capacities

To achieve and maintain the maximum quality of your Tandberg Data tape drive, we recommend using Tandberg Data media.
Drive Model Tandberg 220LTO Tandberg 420LTO LTO1, 2, 3 LTO Ultrium Generation 2 (Native format) LTO Ultrium Generation 1 (Read/Write compatible) Cleaning Cartridge for LTO1, LTO2 and LTOm 609 m 200 GByte 100 GByte 31 Media Name Tape Length 609 m Capacity (Native) 100 GByte Ordering no. 30
LTO Ultrium Generation 1 (Native format)

Table 3

Media alternatives
External Tabletop Enclosure
ON/OFF Switch Cooling Fan SCSI_ID Switch
SCSI Interface Connectors

Figure 6

External tabletop enclosure, rear side

Power Requirements

Tandberg 220/420LTO in external tabletop enclosure: AC Input: 100 VAC / 0.6 A or 240 VAC / 0.3 A, 50-60 Hz Tandberg 220/420LTO as standalone: DC Input (typical operation): 5 VDC / 2.1 A, 12 VDC / 0.6 A

Heat Dissipation

Tandberg 220/420LTO as standalone: Operating: 18 W Sleep mode with cartridge inserted: 9 W 6
Total customer satisfaction is of the utmost importance to Tandberg Data.
We guarantee that this product left our premises defect free. If you are not satisfied with the quality of this product, please contact your distributor or the nearest Tandberg Data office to have the problem solved! For more documentation and information, please see our website www.tandberg.com.

Tandberg Data

International headquarter
Tandberg Data ASA, Kjelssveien 161, Oslo, P.O. Box 134 Kjelss, N-0411 Oslo, Norway. Tel: +90. Fax: +50. www.tandberg.com

Worldwide subsidiaries

Tandberg Data Corp., 13000 Gregg Street, Poway, CA 92064, U.S.A. Tel: 858-726-1800. Fax: 858-726-1801 Tandberg Data GmbH, Feldstrasse 81, D-44141 Dortmund, Germany. Tel: +5436 0. Fax: +5436 111. Tandberg Data S.A.S., 16/18 Ave. Morane-Saulnier, F-78941 Vlizy Cedex, France. Tel: +01 01/00800-82632374. Fax: +(for technical support: 00800-07867243). Tandberg Data (Asia) Pte. Ltd, 20 Bendemeer Road, #04-05 Cyberhub, Singapore 339914, Tel: +0786. Fax: +0787. Tandberg Data (Japan) Inc., Eitaibashi Eco-Piazza Bldg. 8th floor 29-13, Shinkawa 1-chome, Chuo-ku Tokyo 104-033, Japan Tel: +5566 2871. Fax: +5566 2875. Tandberg Data Ltd., Bloxham Mill Business Centre, Barford Road, Bloxham, Banbury, Oxfordshire, OX15 4FF, United Kingdom Tel: +44 (0) 8450706916.

Specifications subject to change without notice. All trademarks are the property of their respective owners. 2006 Tandberg Data ASA. All Rights reserved. Part No. 433261-04. February 2006.