NOT 1765/1770 017110

29/01/03

Page 1

017110 - 04/03

English

Please read these instructions carefully and keep for future reference.

1- STEAM IRONING

Filling the water tank
Unplug your iron before filling it. Set the steam control on DRY (A). Fill the beaker up to the lower line indicated (B). Open the water tank filler cover completely (C), set the iron on a table (not when the iron is hot) shown in the diagram (D) below, and fill the tank. - Do not exceed the MAX line indicated on the water tank (with the iron set on its heel). - Close the water tank filler cover.
Obtaining more steam for removing wrinkles

(depending on the model)

ULTRAGLISS DIFFUSION
Shot of Steam Button (depending on model)

for removing wrinkles

- Press the shot of steam button from time to time (I). - Wait a few seconds between each shot before pressing the button again.
Vertical steam ironing (depending on the model)
Auto-Stop safety warning light Spray Button to moisten linen Water tank filler cover Steam control

(depending on model)

- Hang up the garment on a hanger and hold the fabric slightly taut with one hand. - Set the thermostat control on MAX (J). - Press the shot of steam button ( ) repeatedly (K), moving the iron from top to bottom (L). - Hold the iron a few centimetres from the fabric to avoid burning delicate fabrics.

Electric power cord

A B C D

Setting the temperature

Anti-calc valve
To be cleaned once per month
- Set the temperature control shown in the diagram below (E) referring to the table below (or on the heel). - The thermostat light comes on.Wait for the light to go off and come on again before you start ironing (F).
Auto-Stop safety feature (depending on the model)
- The electronic system cuts off the electric power and the AutoStop warning light flashes if the iron is left vertically on its heel for more than 8 minutes, or in a horizontal position for more than 30 seconds (M). - To restart the iron, just move it gently until the warning light stops flashing. Note : When the Auto-Stop warning light is on, it is normal for the thermostat light to be off.
Thermostat indicator light.
Goes out when the temperature has been reached. E F

Sole plate

Water tank maximum fill line

Do not exceed this limit

Thermostat control
For choosing the ironing temperature
Setting the steam level (G)
- In order to avoid water dripping from the iron onto the linen: Turn off the steam when ironing silk or synthetic fabrics. Set it at the minimum position for wool.
Warning ! Remove the sole plate protector before heating up the iron (depending on the model).

2- DRY IRONING

- Set the steam control on DRY (see diagram A). - Set the temperature. - You may start ironing when the thermostat light goes out and comes on again.
Warning ! Before using your iron with the steam function for the first time, we recommend that you operate it in horizontal position for a few moments, away from your linen, ie press several times on the shot of steam button. During the first few uses, a harmless odour and smoke may be given off.This has no effect on the use of the iron and will disappear quickly.

What temperature and which steam setting to use ?
FABRIC LINEN COTTON WOOL SILK
Polyester, Acetate, Acrylic, Nylon
POSITION OF THERMOSTAT CURSOR MAX
STEAM SETTING POSITION MAX

SYNTHETIC

qqq qq q q

3- MAINTAINING YOUR IRON

BE CAREFUL ! Unplug your iron and let it cool off before cleaning it.

= STEAM ZONE

What water to use ?
Your appliance has been designed to function with tap water. However, it is necessary to operate the Self-Clean function regularly in order to eliminate hard water deposits. If your water is very hard (check with your water authority), it is possible to mix tap water with store-bought demineralized water in the following proportions : 50% tap water, 50% demineralized water.
CLEANING THE ANTI-CALC VALVE (Once per month) : - Unplug your iron and empty the water tank. - To remove the anti-calc valve, pull it up using the tabs located on each side (N). NEVER TOUCH THE END OF THE VALVE.
Moistening the linen (Spray)
- When steam or dry ironing, press several times on the Spray Button to moisten the linen (H) and to remove stubborn creases. - Make sure that there is water in the tank before using this button. H
Recommendations: Fabrics and ironing temperatures: Your iron heats up quickly: begin by ironing those fabrics that are ironed at low temperatures, then go on to those requiring a higher temperature; If you turn down the thermostat, wait until the thermostat light comes back on before beginning to iron again. When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate of the fibres.
Types of water not to use :
Heat concentrates the elements contained in water during evaporation. The types of water listed below contain organic waste or mineral elements that can cause spitting, brown staining, or premature wear of the appliance: water from clothes dryers, scented or softened water, water from refrigerators, batteries, or air conditioners, pure distilled water, or rain water.

- Soak the valve in a cup of white spirit vinegar or plain lemon juice for 4 hours (O). - Rinse the valve in tap water. - Place the steam control on dry. - Replace the anti-scale valve.
THE IRON WILL NOT FUNCTION WITHOUT THE ANTI-CALC VALVE
3- MAINTAINING YOUR IRON (continued)
USING THE SELF-CLEANING FUNCTION : In order to extend the life of your iron, use the Self-Cleaning function once per month. - Unplug your iron and set the steam control on DRY. - Fill the water tank up to the limit (see recommendations for the types of water to use). - Leave water tank filler cover open until the end of the operation. - Place your iron on its heel and set the thermostat control on MAX. - Plug in your iron and wait until the thermostat light goes out. - Unplug the iron and hold it over a sink in the horizontal position. - Place the steam control on MAX. - Raise the anti-calc valve without removing it completely. - Shake the iron gently, over the sink, until all of the water in the water tank (with the impurities) has flowed out via the sole plate. - At the end of the operation, push the anti-calc valve back into position. - Turn the iron back on for 2 minutes, setting it on its heel, to dry the sole plate. - Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth.
Recommendation : The self-cleaning function helps to delay the scaling of your iron.

4- STORING YOUR IRON

- Unplug it and wait until the sole plate has cooled off. - Empty the water tank and set the steam control to DRY. - Store the iron on its heel.

FOR YOUR SAFETY

Warning! The voltage of your electrical installation must correspond to that of the iron (220V-240V or 127 V depending on the model). Connecting to the wrong voltage may cause irreversible damage to the iron and will invalidate the guarantee. This iron must always be plugged into an earthed socket. If using a mains extension lead, ensure that it is correctly rated (10A or 13A for UK only), with an earth. If the electrical cord becomes damaged, it must be immediately replaced by an Approved Service Centre to avoid any danger. Never immerse your iron in water! The appliance must be unplugged before filling or emptying the water tank. If the appliance falls, have it checked by a professional before using it again; unseen damage may be dangerous. The sole plate may be very hot: - Never touch it. - Always let it cool off before putting it away. - Never leave your iron unattended when it is plugged in or while the soleplate is still hot. - Always keep your iron out of the reach of children. NEVER DISMANTLE YOUR IRON ; ALWAYS CONTACT AN APPROVED SERVICE CENTRE. This product has been designed for domestic use only. Any professional use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no resposibility and the guarantee will not apply.

GUARANTEE (U.K. ONLY)

Details of the guarantee are shown on the guarantee card enclosed with the appliance.This guarantee does not affect your statutory rights. Should service or further information be required please contact the Tefal Customer Relations Department (see Helpline or enclosed Service Information leaflet). Do not attempt to dismantle the appliance yourself this will negate the guarantee. In line with a policy of continuous product improvement,Tefal reserves the right to change product specifications without prior notice.
CLEANING THE SOLE PLATE: - While the soleplate is still just warm, clean it by rubbing it with a moist, non-metallic pad.

5- IS THERE A PROBLEM ?

Problems
The iron does not heat up. Water drips from the holes in the sole plate.

Possible causes

The auto-stop safety switch has operated Thermostat control not correctly positioned The chosen temperature is too low and does not allow for the formation of steam. You are using steam while the iron is not hot enough. You are using the shot of steam button too often. The steam flow is too high. You have stored the iron horizontally, without emptying it and without setting it to DRY.

Solutions

Restart the iron by lightly moving it. Set the thermostat control to the required fabric to be ironed. Set the thermostat in the coloured zone (from qq to MAX). Wait until the thermostat light goes out. Wait a few seconds between each use of the button. Reduce the steam flow. See the section "Storing your iron". Do not add any descaling agents to the water in the water tank. Do a self-cleaning and use tap water or 50 % tap water and 50 % demineralized water. Do a self-cleaning. Clean the sole plate with a non-metallic sponge. Vacuum the holes of the sole plate from time to time. Ensure linen is rinsed thoroughly to remove any soap deposits or chemicals on new garments which have been sucked up by the iron. Clean the sole plate as indicated above. See the temperature table to correctly set the thermostat. Clean the sole plate as indicated above. Always spray starch onto the reverse side of the fabric to be ironed. Fill it with tap water. Clean the anti-calc valve. Clean the anti-calc valve and do a self-cleaning. Do a self-cleaning. Always set your iron on its heel. Try to avoid ironing over zips which may have rough edges.

SAFETY POINTS FOR REWIREABLE OR MOULDED PLUG.
The mains lead is fitted with a BS A plug. If the plug supplied with the product is not suitable for your socket Brown or outlet, then it must be removed (cut off, if it is a moulded-on plug) red and a suitable 3 pin plug fitted in accordance with the instructions Green and yellow given below. or green Fit IF YOU ARE IN ANY DOUBT, PLEASE CONTACT A QUALIFIED correct ELECTRICIAN. fuse Blue or WARNING :This appliance must be earthed. black Use cable Dispose of a plug that has been cut from the power supply cord, as gripper such a plug is hazardous if inserted in a live 13 amp socket outlet elsewhere in the house. How to connect the cord to a U.K. plug : IMPORTANT :The wires in the mains lead are coloured in accordance with the following code : Green & Yellow Earth Blue Neutral Brown Live Please read the instructions given below before connecting the cord to a plug. If you are in any doubt please consult a qualified electrician. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows : The wire that is coloured GREEN & YELLOW must be connected to the terminal in the plug which is marked with the letter E, or the earth symbol , or coloured GREEN or GREEN & YELLOW. The wire that is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. The wire that is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. This appliance requires a 13 amp fuse. Should the fuse need to be replaced an ASTA marked fuse, approved to BS 1362, of the same rating must be used. Always replace the fuse cover after fitting a fuse.The plug must NOT be used if the cover is omitted or lost until a replacement is obtained make certain that only the correct fuse cover is used and fitted. For plugs with a detachable fuse cover, the replacement must be the same as the colour insert in the base of the plug, or as directed by the embossed working on the base of the plug. If the detachable fuse cover is lost, a replacement may be purchased from a Tefal Service Centre (see enclosed Service Information leaflet).

Brown streaks come through the holes in the sole plate and stain the linen.
You are using chemical descaling agents. You are using pure distilled water. Fabric fibres have accumulated in the holes of the sole plate and are burning. Your linen is not rinsed sufficiently or you have ironed a new garment before washing it.
The sole plate is dirty or brown and can stain the linen.
You are using too high a temperature. You are using starch.
There is little or no steam.
The water tank is empty. The anti-calc valve is dirty. Your iron has a build-up of scale. You iron has been used dry for too long.

HELPLINE

If you have any problems or queries, please call ou Customer Relations Team on : 1454 - UK (01) 4751947 - IRELAND Or consult our web site : www. tefal.co.uk
The sole plate is scratched or damaged.
You have placed your iron flat on a metallic rest-plate. You have ironed over a zip.

ULTRAGLIDE DIFFUSION

English

049494 - 24/01

Avantis
Read these instructions carefully and make sure you keep them.

1- STEAM IRONING

HELPLINE : FOR ANY PROBLEMS OR QUERIES, PLEASE TELEPHONE 1454 (UK - calls charged at local rate) or (01) (Ireland)

Safety warning light

(depending on the model turns the iron off if it has been forgotten)

FILL THE TANK

- Place the steam control on DRY (coton). katoen lai wol - Open the flap of the water tank filler,onee s place the iron on a table (not when i zijde sy nth synth iron is hot), as shown. in the. diagram below, and then fill it.

linnen

min. linen Be careful ! lin c o t ton c on You shouldoatinot fill the tank wool l ne s il k max. syn beyondhethesysotie. MAX level (iron AUTO t ti c nh li n linnen standing vertically on the heel). c oton katoen

Boost of steam button

(for extra steam and vertical steam)

(for fastening the cord)

ANTI-DRIP FUNCTION (depending on the model) The supply of water is cut off automatically to avoid any drips from the soleplate when the temperature of the iron is insufficient to max. produce li n e n steam. max. AUTO cot t When first using the iron, wait for 5 minutes for steam to be produced.on wool li n
linnen c oton s VERTICAL STEAM (depending katothe model) on en lain e wol s max. max. zijde AUTO oie li n e n s y n t h. le i n e n synth.
cotton baumw. wool wolle s il k seid e synth. kunstfasen
lin coton laine s il k soie synthetic synth.

Spray button

(for dampening laundry)

Steam control

li n c oton lain e so ie s y n t h.
linnen katoen wol zijde synth.

lain e so ie s y n t h.

wol zijde synth.
li n e n lino comion algodn tt n. wool lan a s il k se d a synth. sintticos

Water tank filler

SETTING THE TEMPERATURE AND STEAM LEVEL - Place the thermostat controlminto match the type of fabric to be ironed.

min. min.

li n e n lin c o t ton coton wool laine s il k soie sy nt AUTO hetic synth.
lin coton laine soie synth.

Thermostat light

(goes out when the required temperature has been reached) (for choosing the temperature) li n c oton (do not fill beyond this limit) lain e so ie s y n t h. with an integrated system that
linnen katoen wol zijde min. synth.
Linen Cotton AUTO Wool Silk, Viscose

Anti-calc valve

Soleplate
Maximum tank filling point

Thermostat control ma

Synthetics
Polyester, Acetate, Acrylic, Polyamide
li n e n Hang the garment up and hold the fabric taut. cot t max. AUTO of l Place the thermostat control on MAX 1 , press repeatedly on the Burst wooon li n li from s il k Steam button ( ) 2 and move the ironnnen top to bottom. 3 sy nt c oton ato n kthe egarment to avoid burning delicatehetic Hold the iron a few centimetres from lain e wol fabrics. so ie zijde sy nth s REMOVING STUBBORN.CREASESAUTO synth. min. max.
li n e n lin c o t ton coton wool laine s il k soie synthetic synth.
Your iron is equipped protects against the effects of lime-scale (depending on the model).
Press repeatedly on the Spray ( ) button to dampen the fabric. Or, use the Burst of Steam button ( ), pressing repeatedly to obtain a more powerful burst of steam.
The light comes on. Wait for the light to go off and come on again before you start ironing We recommend that you: - Start with the fabrics to be ironed on a low temperature () and finish max. with AUTO which respond best to higher temperaturesne( orleMAX) AUTO those li n in e n linnen cott n baumw. katoen If you lower the thermostat, wait until the light comesoon again before wool l wolle woironing. s il k seid e zijde If temperature synth. you iron a fabric made of a blend of fibres: set the synth. kunstfasen for the most fragile fibre. Be careful! Your iron will only produce steam min. when the thermostat control is in the coloured zone.
Your new Avantis iron represents the latest in ironing technology : AUTOSTEAM : All Avantis irons now feature autosteam.This ensures that ma you get the correct level of steam whatever the temperature you x.have set, li n li n linne preventing nwatermarks and drips. c oton c oto katoen ULTRAGLIDE DIFFUSION SOLEPLATE : The new Avantis uses Tefals n lain e lain e wol so ie so i patentedzijtechnology with its unique Ultraglide Diffusion soleplate.This givese de sythe iron yunrivalled glideability and steam diffusion, reducing your ironing synth. n t h. s nth. time and making your ironing easier. ANTI-CALC VALVE : Tefal have introduced the Anti-calc Valve to ensure min. easy cleaning and improve resistance to scale. Be careful ! (depending on the model). Take off the soleplate protection before heating the iron. When the appliance is used for the first time, a harmless odour and smoke may be given off. This has no effect on the use of the appliance and will disappear quickly. AUTO

AUTO-STOP SAFETY FEATURE (depending on the model) max. The electronic system cuts the power off and li n e n lin max. AUTO c o t ton coton the auto-stop warning light flashes if the iron is li n e n lino AUTO wool AUTOe lain AUTO c ot ton min. lgod the heel forn more than 8 s il k soie left vertically aonn li linnen wool synthetic synth. lan a c n katoen minutesilk for more than 30ointoseconds if or la e wol s se d a so ie zijde synth. sint left horizontal. ticos s y n t h. synth. To restart the iron, shake it gently until the min. warning light stops flashing. max.

max. max.

li n e n

AUTOMATIC STEAM

AUT UTO
s VARIABLE STEAM (depending on the model)
cotton AUTO to co Warning:The linauto-stop features will only operate 2 minutesnen li n li n lai nen nen linwool c oton oton oe o ln katsiek soie after the lcaironkatisnl switched on. lain e in e wo wn syol thetic synth. so ie so ie zijde zijde N.B.Whenh. thenthauto-stop safety feature cuts in, itntis normal sy nt s y h. sy. synth. for the thermostat light to be off.
Water to use in your iron ?
Your iron has been designed to be used with tap water. However, the cleaning feature has to be used regularly to eliminate any mineral build-up in the steam chamber. If your water is very hard (check with your Local Environmental Services or water company), you can use a mix ofmin. tap half water and half distilled water. Do not use any other types of water
li n e n lin c o t ton coton wool laine s il k soie s self-ynthetic synth.
- Place the Steam AUTO Control on AUTO ( ) (depending on the model) The production of steam automatically adjusts to lithe temli n e n n c o t ton ton peraturecoselected.
wool s il k s y n t h e ti c
- You can set the steam manually. It is not advisable to use steam on silk or synthetics. This could cause stains.

2- IRONING WITHOUT STEAM

Place the Steam control on DRY ( ). You can start ironing when the indicator

AUT UTO AUTO

light comes on for the second time.

laine soie synth.

3- CARING FOR YOUR IRON
s CLEANING THE SOLEPLATE When the soleplate is cool, clean with a damp, non-metal washing up pad.
4- PUTTING YOUR IRON AWAY

5- TROUBLESHOOTING

Problems and possible causes

Solutions

n lis When you first use, wait 2 minutes max. coton until steam is produced. li n e n lin laine s c o t ton soiePlace the cursor of the thermostat oton c on synth., or MAX and the steam setting e wool
We recommend that: min. when using starch, it should be sprayed onto the reverse side of the fabric and the soleplate cleaned more frequently.
IRON PRODUCES LITTLE OR NO STEAM
Your iron is new.. li n e n The temperature selected is tooilklow. s

s y n t h e ti c

c o t ton wool
Be careful! - Unplug your iron and let it cool down before cleaning. - Do not use detergent or descaling products. - Never put the iron under the tap.
The steam control is on DRY. min
s il k cursor on the coloured zone ( ) soie synthetic synth. Put the Steam control on AUTO
CLEAN THE ANTI-CALC VALVE (at least once every 2 months) Empty the iron and put the ironing control onto DRY ( ) To remove the anti-calc valve, pull upwards by means of the grips located on either side. Leave to soak in white vinegar or pure lemon AUTO max. juice fornearoundlin2 hours. li n t ton c ton Rinsecwounderoathe tap ool l in e s il k soie Replaceheandsyslot down into the housing. s y n t ti c nth.
Place the cursor on DRY. ( ) Unplug the iron and wait until the soleplate has cooled. Empty the tank. 1 Wind the cord loosely around the heel and fix the clip onto the cord. 2 AUTO max. Store the iron upright onnits heel. li n e lin
c o t ton coton wool laine s il k soie synthetic synth.
Your iron is clogged with scale or has s Clean the anti-calc valve and set the min. max. been used dry for too long.. self-clean feature in motion. li n
IS DRIPPING FROM THE HOLES IN THE SOLEPLATE
s Wait a few seconds before each use. You have been using the Burst of Steam control too often.. s Take the iron to an approved The thermostat is not functioning min. correctly... service centre.
en lin c o t ton coton wool laine s il k soie synthetic synth.

SAFETY PRECAUTIONS

Be careful! the iron only works if the anti-calc valve is in place
SELF-CLEANING (twice a month)
x. Fill the tank to the MAX mark (seeenour recommendations on the type of li n lin c o t ton water to use). coton wool laine Put the thermostat control on MAX and the steam control on DRY ( ) s il k soie synthetic synth. and switch on. 1 Place the iron on its heel and wait around 5 minutes. Unplug the iron and placemin. over the sink horizontally. max. Completly remove the anti-calc valve. li n e n lin c o t ton AUTO c on Shake max. iron lgently until all the water (and any impurities) has drainedoatine max. the wool l in linnen s il k soie from the soleplate.on2 katoen c ot synthetic synth. lain e wol Replace the anti-calc valve. so ie zijde s y n t h. When the soleplate is justh.warm, wipe the iron with a soft cloth. sy nt

Be careful! Your electrical installation must correspond to that of your iron (220-240V). Connecting to the wrong voltage may cause irreparable damage to the iron and this will invalidate the guarantee. This iron must be plugged into an earthed socket. If you are using an extension lead, ensure that it max. bipolar (10A-or 13A for UK only) with an earth. is li n e n i If the cord is damaged, it cmust betlonn o t ton co replaced immediately by an Approved Service w laine Centre as this is dangerous.ilool s k soie syntwater!nth. h e ti c sy Never immerse the iron in The appliance must be unplugged before filling or emptying the tank If the iron is dropped, have it checked by a professional before reuse: invisible min. damage may be dangerous. Your appliance gives off steam which can cause burns. The soleplate of the iron may be very hot: - never touch it - always leave it to cool before you put it away - never leave your iron unattended when plugged in or when the soleplate is still hot. - keep your iron away from children. NEVER TAKE YOUR IRON APART: CONSULT YOUR APPROVED SERVICE CENTRE (SEE AUTO SEPARATE LEAFLET).
s Wait until the thermostat indicator light goes out before using the steam the Iron put away with water in the tank s Empty the tank and putmax. iron away and the cursor on the steam position. vertically, standing on its heel. Position lin li n e n c o t ton the cursor on DRY. coton
Steam used before the iron is hot.
s il k BROWNISH WATER IS DRIPPING FROM THE SOLEPLATE AND IS STAINING

THE LAUNDRY

You are using chemical descaler products or pure demineralised water.. Fabric fibres have accumulated in the soleplate holes or between the iron body and the soleplate and are singeing...
Operate the self-clean feature and follow our recommendations (see the min. paragraph: "The water to use") s Clean the soleplate with a non-metal, washing up pad. Vacuum the soleplate holes from time to time. Operate the self-clean feature.
SOLEPLATE IS DIRTY OR BROWN AND IS SOILING THE LAUNDRY
You are using a temperature that is too high..
Your laundry has not been sufficiently rinsed or you are using starch.
Clean the soleplate. See the paragraph "Setting the temperature". Clean the soleplate. Spray starch on the other side of the fabric to the side being ironed.
li n coton laine so ie s y n t h.
WIRING wol INSTRUCTIONS (FOR U.K. ONLY). lain e s You have placed your iron horizontally so ie s Always place your iron on its e z this Warningsy:injdh. appliance must be ears y n t h. t on a metal support.. heel. thed. Brown Important : the wires in this lead are or red L Green and coloured in accordance with yellow the following codes : E or green Fit correct This appliance is designed for domestic use only. In the case of professional - Green and yellow : earth fuse use, inappropriate use or failure to comply with the instructions, the manu- Brown : live black N Blue or Use cable facturer accepts no responsibility and x.the guarantee does not apply. AUTO - Blue : neutral. AUTO max. ma max. max. gripper AUTO AUTO AUTO AUTO li n e n lliinen li n e n line liConnectnnen green/yellow wire to the nn linolino le i n e n no l leineni the leinen cotton algodncotone baumw. co cotterminal watothe plug marked E cotton algocotn on baumw. in t o n t o n bau m k. e n d t wool wna l wool woollainby theeearth symbol or coloured green and yellow. l an a oo wolle lan a la wolle or e woll wol sida s il k s il k so ie s il k seid e jd e sedaseta seide zithe seid e se l k synth. sintticossint. kunstfasen y nt synhs.Connectynth. brown wire to the terminal in the plug markedyL orttiscos h. kunstfasen s nth. sin colout h. t ynkunstfasen s red red. Connect the blue wire to the terminal in the plug marked N or coloured black. A 13 amp fuse should be fitted when the appliance is connecmin. min. min. min. ted to a BS 1363A plug. Seek professional advice if unsure of the correct procedure for the above. Important : If the electrical cord of this appliance is damaged or shows signs of wear, it must only be replaced by an authorised Tefal Service Centre (see section After Sales Service - see separate leaflet).

li n c oton

linnen katoen
SOLEPLATE IS SCRATCHED OR DAMAGED