A zone is part of the protected premises and may consist of one or more detection devices protecting rooms and points of entry/exit, (e.g. front door, kitchen, downstairs windows, upstairs bedrooms, etc.). When the alarm system is fully armed, all of the zones on the system are monitored. Some zones may belong to more than one area, such as points of entry/exit i.e. the front door and movement sensor in an entrance lobby. These are called global zones because they are assigned to multiple areas. A zone that is assigned to more than one area will only be monitored when all of the areas it is assigned to are armed.
An area is a group of one or more zones and would normally be used to split the premises into different sections. Each area can be either Full armed or Part armed. Example 1: Domestic Premises The entire house could be area A. Each area can be Part armed. For instance, detection devices upstairs, i.e. PIRs, could be programmed so that they will not be monitored during a Part arm, allowing access to the upstairs of the house at night.
Area A forms the entire alarm system.
Example 2: Domestic Premises The upstairs of a house could be area A, the downstairs could be area B and the garage could be area C. Each area can be Full armed independently from each other (all detection devices in the area monitored). For instance, downstairs and the garage in example 1 (areas B & C) could be armed at night allowing access to the upstairs of the house (area A).
All of the areas together form the entire alarm system.
Example 3: Commercial Premises Office 1 in an office block could be area A, office 2 could be area B and office 3 could be area C. Each area can be armed and disarmed independently from each other. For instance, any of the offices in example 2 above could be armed and disarmed to allow access without affecting the other offices.
Example 4: Office Block The foyer of the office block in example 4 would need to be armed when the last office is armed and disarmed when the first office is disarmed. Because the foyer is a global area (used by everyone) the zones in that area need to be assigned to areas A, B and C. This ensures that the zone is only recognised by the system when ALL areas (A, B & C) are armed, allowing access to the foyer even if one of the areas is still armed.

Monitoring

This alarm system is capable of reporting Intruder alarms, Panic alarms, Fire alarms and other types of information over telephone lines to an Alarm Receiving Centre. If you accidentally set the alarm off, call the Alarm Receiving Centre immediately to prevent an unnecessary response.

The monitoring function must be enabled before it will work. 5

Keypads

One or more keypads will be installed throughout the protected premises, usually one at each entry/exit door. The keypads are used to perform all of the system functions i.e. Arming, Disarming etc.
Premier LCDL/LCDLP Large Display Premier LCD/LCDP Standard Display
Proximity Reader (LCDP & LCDLP keypads only)

Screen Not Shown

Omit Service

Info. Ready

Programmable Info. LED

Normal Keys

2 abc 5

3 def 6 mno 9 wxyz

Omit Chime Part Area

4 ghi 7 pqrs

8 tuv 0 _

Function Keys

Display Window (Premier LCD/LCDP & LCDL/LCDLP) The 32-Character LCD display is used to show the status of the system and to view system data. Proximity Reader (Premier LCDP & LCDLP only) Built in Proximity Reader for use with Proximity TAGS (approximate range is between 1 and 5 cm). Proximity TAGS can be used as an alternative to a Code number. LED Indicators Five LED indicators have been provided to indicate the status of the system. LED

Power Service Ready

Status
On Flashing On Off On Off Flashing

Meaning

AC mains is present on the control panel AC Mains is not present, the control panel is running on the standby battery The system requires attention, contact your installer The system does NOT require attention All zones are secure and the system is ready to be armed One or more zones are active The system has zones (with the Force Omit attribute) that are active The system is armed (can also be programmed for other indications) The system is unarmed (can also be programmed for other indications) One or more zones are omitted No zones are omitted

Info. Omit

On Off On Off
Keys ! to " These keys are for entering User codes or programming data. Yes & No Keys # & $ The YES key is used to accept actions and the NO key is to cancel actions or edit data. Omit Key % This key is used to omit zones (see page 23 for details). Chime Key & This key is used for turning the chime facility on and off (see page 24 for details) and also for turning the Exit tones on and off during the exit mode. Part Key ' This key is used to part arm the system (see page 16 for details). It can also be used to do a Quick part arm if this feature is enabled. Area Key ( This key is used to arm or disarm particular areas (see page 17 for details). It can also be used to do a Quick arm if this feature is enabled. Reset Key ) This key is used to exit from a menu or to reset the system (see page 21 for details). Scroll Key * This key is used to scroll through the various menus and options and also to slow down the display if it is scrolling through alarm information too fast. Menu Key + This key is used to select the Arming or User menu.

Emergency Keys

In case of emergency, the alarm system can provide three immediate emergency alarms by pressing and holding two specific keys. Press Keys UK Response
Panic Alarm (PA) Fire Medical

Export Response

Fire Panic Alarm (PA) Medical
!&, -&. /&"
The emergency keys can be enabled/disabled for each keypad on the system. The Panic alarm can be programmed for either audible or silent operation. The Panic alarm can be programmed for either instant or delayed operation.

The Quick Arm Keys

The Quick Arm keys allow the system to be armed without having to enter a User code first.
The Quick Arm keys will only work if the keypad has been programmed to allow arming in this way. To FULL arm the system, press (. To PART arm the system, press !, 0 or , followed by '.

Keypad Lock

The keys on the keypad can be locked to prevent unwanted access to the system.
The Emergency keys will NOT operate with the keys locked. To Lock the keys, press # and $ together. To Unlock the keys, press # and $ together again.
Alert, Reset and Service Messages
System Alerts When an alarm or fault condition exists on the system the keypad will display a warning message.
"#$%&'! ()&*%$+ ,-.,-.- /!,0123
In order to display the alarm or fault condition(s) that generate this alert, enter your user code, a scrolling display will show all alarm/fault conditions on the system. When alarm information is being displayed, pressing the SCROLL key will slow down the display and also allow manual scrolling through the events. The messages that can be displayed are shown in Reset and Service messages below and in Fault Messages on page 10. Reset and Service messages When the system requires a reset/service the display will show one of three messages. These messages can also be accessed at any time from the normal display.
These messages may have been changed by the installer and may contain the telephone numbers of the installer or the Alarm Receiving Centre.
To display the reset/service messages, proceed as follows:
Press + followed by ! to view the Service message
45))!()5 *'!467 !!86*!"& *9:;&
Press + followed by 0 to view the Reset message
45))!<=>:=&&*!%6 !!?&$&%!"#$%&'
Press + followed by , to view the Anti-code message
45))!(?4!%6 ?&$&%!"#$%&'
Press ) to exit from the messages The display will return to normal.

Fault Messages

@5:=$!A6B&*!CDD !EF&!-G!@5*!H--,
There is a Mains failure (the keypad may chime every minute, enter a valid User code or press to stop the chime). The display will automatically clear when mains is reapplied.
(E"!A5%I !85F)% !EF&!-G! @5*!H--,

Some action may be required to clear the cause of the alarm or fault in order to successfully reset the panel. INS177

To RESET After an Alarm

If the display shows SYSTEM ALERTS, follow the steps described in To DISPLAY the causes of System Alerts above, before attempting to reset.

USER Reset

Once the alarm has been silenced (see above), the system will need to be reset.
If the system has been programmed to be reset by an Engineer, pressing ) will not return the display to normal, if this is the case see ENGINEER Reset (page 20) for details. The system may have been programmed to be reset by Anti-code, if this is the case, see ANTI-CODE Reset (page 20) for details.
To reset the alarm, proceed as follows:
Press ) The external strobe will stop, the system will chime and the display will return to normal.

ENGINEER Reset

If the system has been programmed to be reset by an Engineer following an alarm activation, you will still be able to silence the alarm by entering a valid User code (see page 20 for details).
The system cannot be armed again until the alarm has been reset.
Contact the telephone number on the display (if programmed) or the telephone number on the last page of this User Guide.
Operating the Alarm System ANTI-CODE Reset
If the system has been programmed to be reset using an Anti-Code following an alarm activation, you will still be able to silence the alarm by entering a valid User code (see page 20 for details).
A*&$$!?<"<E!D6* (=%:Z;6N&
Press ) The display will show a random code number i.e. 4281
aF6%&!S!0Hb, ?&L)#!S!ZZZZ
Contact the telephone number on the display (if programmed) or the telephone number on the last page of this User Guide and quote the random code number. You will be given a 4-digit Anti-Code i.e. 5624 Enter the Anti-code that has been given to you 1111
aF6%&!S!0Hb, ?&L)#!S!3GH0
Press # If the Anti-code is correct, the keypad will chime to indicate that the system has been reset and the display will return to normal.

To OMIT Zones

It is possible to exclude (omit) individual zones when arming i.e. if a zone is in fault. Users with access to this function can only omit zones that have been programmed as Omittable.
If the zone can be omitted, there will be a star to the right of the zone number. Only zones that have the Omit attribute assigned to them can be omitted. A star will appear to the left of the zone number to indicate that the zone has been selected for omitting. All omitted zones will be automatically reinstated the next time the system is disarmed, unless programmed otherwise. To re-instate zones manually, simply follow the instructions again. However, when the % key is pressed this time, the zones will be re-instated.

To omit 24 Hour zones, proceed as follows:

Press "

R6!#6F!B5=%!%6 C':%!H0Y*!V6=&$
V6=&!-,3!"&;F*& J5;U!R66*!!!!!!S
% to omit the selected zone
V6=&O-,3!"&;F*& :$!C':%%&N V6=&O-,3!"&;F*& J5;U!R66*!!!!!!S
Repeat for other zones Press + when finished Press ) to exit the menu The display will look like this:
O!V6=&$!C':%%&N!O !EF&!-G!@5*!H--,
The selected 24 Hour zones are now omitted. 26 INS177
To SELECT Areas for Chime
When a zone is enabled for Chime the Keypad will generate a chime tone every time the zone is activated. Users with access to this function will be able to turn Chime on and off for selected areas. Zones within an area can be individually programmed for Chime in Edit Chime Zones (see page 36 for details).
Only areas that have been programmed for Chime can be selected. A star means the area can be selected and a dot means the area cannot be selected. Pressing 3 will select/deselect all areas. Pressing ( will toggle between areas A to H and I to P (Premier 168 only).
To select an area for Chime, proceed as follows:

Press &

<=5\)&!4I:'&!6= !!S!OOO77777!_
Use keys ! - 5 to select/deselect areas (i.e. !, 0 and , = Areas A, B and C)
<=5\)&!4I:'&!6= !!S!(J477777!_
Press # when finished Press ) to exit the menu The display will return to normal.

To VIEW Activity Faults

If any zones with the Activity attribute have not been activated within a certain time period, an activity fault will be displayed at the time of arming. Users with access to this function will be able to view the activity faults.
To view activity faults on a Premier 24, the View Zone Status menu must be used (see page 25 for details). The system may have been programmed so that an activity fault will not allow arming. If this is the case the system can only be armed once the zone in fault has been activated (forced walk test). Only zones with the Activity attribute that have not been activated will be shown.

! 0 , 4. / 5 " * * * * * * * *

Viewing the Event Log

Users with access to this option can view the system Event Log. This log records all of the events that occur on the system, i.e. Users entering their codes to arm or disarm the system, alarms, failures to arm etc. along with the time and date on which they occurred.
The down key moves you to the previous event (backwards in time), and the up key moves you forwards again. The ( key toggles between the area information and the time/date. For a full list of Event Log descriptions, please refer to the Master User Guide.
To view the Event Log, proceed as follows:

Press +

46N&!-,!R59:N !,H1Hb7-0!-G.-2
Press * to scroll up and down through the Log
(*&5$!R:$5*'&N !,H1Hb7-0!-G.-2
Press ( to toggle between the area information and the time/date Press ' to display zone text (where applicable)
(*&5$!R:$5*'&N !!!!(7777777

Event Log Descriptions

Log Event
KSW ### Active RKP #,# MEDICAL RKP #,# FIRE RKP AUD PA #,# RKP SIL PA #,# DURESS ALARM Active BELL Active REARM LOCK ### CROSS ### USER ## AREAS EXIT ARMING FAILED AREAS ENTRY ARMING SUITE ARMED WITH L/F AREA Armed AREA Disarmed PART Armed TIME Armed TIME Disarmed DEFERRED ALARM ABORT REMOTE Armed REMOTE Disarmed QUICK Armed RECENT Armed #,# RESET AREAS Engineer Reset Anti-Code Reset Remote Reset Redcare Reset Key switch Reset User Reset EXP #,# Reset

Description

A Keyswitch zone type has been activated (zone number ###) A Medical alarm (7 & 9) has occurred from keypad number #,# A Fire alarm (4 & 6) has occurred from keypad number #,# An Audible PA alarm (1 & 3) has occurred from keypad number #,# A Silent PA alarm (1 & 3) has occurred from keypad number #,# User ## has entered a Duress Code at a keypad An Intruder alarm signal has been activated for area ? The Bell output has been activated for area ? Zone ### has re-armed after causing an alarm A Verified Cross Zone Alarm has occurred from zone ### User ## has entered their code The Exit mode has been started for area ? A Exit Error-Arm Fail has occurred on area ? The Entry mode has been started for area ? Area Arm Suite # was used to arm the system The system has been armed with a Line Fault condition present Area ? has been armed Area ? has been disarmed Area ? has been Part Armed Area ? was armed automatically using one of the timer controls Area ? was disarmed automatically using one of the timer controls The arming mode was deferred for area ? An Open After Alarm-Abort has occurred for area ? Area ? was armed using the Wintex UDL software Area ? was disarmed using the Wintex UDL software Quick Arm from keypad #,# Area ? has been armed recently Area have been reset using keypad #,# following an Intruder alarm A reset has been performed using an Engineers code A reset has been performed using the Anti-code reset procedure A reset has been performed using the Remote Reset input A reset has been performed by the Redcare A reset has been performed using a key switch A reset has been performed using a User code A reset has been performed using the input on expander #,#

Remote PC Reset FUSE #,# FAIL AC POWER LOW BAT POWERED UP BELL FUSE ATS FLT Alarm Panel Line Fault Redcare Line Fault Com??? Line Fault Exp #,# Line Fault COMS FAILED DOWNLOAD START DOWNLOAD END LOG ALERT DATE CHANGED TIME CHANGED
A reset has been performed by the remote download PC The Auxiliary 12V Fuse in device #,# has failed The control panel has registered a AC Mains failure The control panel has registered a low battery condition System Power Up (without doing a factory restart) The control panel Bell Fuse has failed There is a problem with the telephone line The control panel line fault input has been activated The Redcare has detected a line fault The Com300, 2400 or ISDN has detected a line fault The Input on expander #,# has been activated The Communicator has failed to report to the Alarm Receiving Centre An Upload/Download has been initiated The Upload/Download has finished 80% of the Event Log has filled (since the last Upload/Download) The control panel Time has been changed The control panel Date has been changed

Event Log Hotkeys

When viewing the system log there are 9 hotkeys available. These hotkeys allow certain events to be found easier without the need for searching. The following hotkeys are available:
! = Priority Alarms (PA, Fire etc.) 0 = Normal Alarms (Guard, 24hr, Entry/Exit etc.) , = Opens and Closings (Arm, Disarm etc.) - = Omits and Reinstates (Zone Omits etc.) 4 = Maintenance (System Tests, Engineer Program etc.). = Tampers (Zone, Bell, Aux etc.) / = Test Calls (Communicator Active, successful etc.) 5 = Entry/Exit (Entry and Exit Procedures) 3 = User Codes (User codes being used)

Changing Your User Code

Users with access to this option can change their own User codes. User codes are unique to each user and can be 4, 5 or 6 digits long.
Only the User code that is entered to access the change code menu will be changed.
Before changing your code, it is vital that you memorise or write down the new code you are about to program. Failure to remember your code will require an engineer visit to re-program a new code for you. This may incur a call-out charge.
To change your User code, proceed as follows:
Enter the User code that requires changing 1111

Press 0

R6!#6F!B5=%!%6 4I5=>&!46N&K
<=%&*!^&B!46N&S !!!!!ZZZZZZ
Enter a new 4, 5 or 6-digit User code 1111
<=%&*!^&B!46N&S !!!!!ZZbebe
Press # to accept the new code Press ) to exit the menu The display will return to normal.
Setting up Zones for Chime
Users with access to this option will be able to select which zones cause the internal sounders to chime every time they are activated. Chime would normally be used on a front door, back door, exit button etc.
Zones will only cause the internal sounders to chime if Chime is turned on (see page 24 for details on turning Chime on and off).

When the control panel is first installed, only the Engineer code and the Master User code exist, additional users need to be added to the alarm system manually.
The factory default Master User code is 4./5. The Master User code is always User 01 and can never be deleted.

Programming New Users

Each User on the system is made up of the following elements. 1, 2 or 8, 3 and 4, these are essential for the code/TAG to function correctly, items 5, 6 and 7 are optional. 1. User Number When users are assigned to the system, they need to be identified by the control panel. Each user is identified as Users 01, 02, 03 etc. User 01 is always the Master User. 2. User Code This is a unique 4, 5 or 6 digit code number that is assigned to a user (the system will allow a mixture of different lengths). The User code must be entered at a keypad to operate the alarm system. 3. User Areas Any number of areas can be assigned to the selected user. Assigning areas to a user determines which areas can be armed, disarmed, reset etc. by that user. In addition, assigning areas to a user determines which of the area related functions i.e. omitting zones, silent arming etc. will be available to that user. 4. User Types The User type determines which functions are available to the user i.e. arming, disarming, resetting etc. and also, which options the user can access i.e. Setup Users, System Tests etc. 5. User Time Lock This option allows the selected user to be denied access to the system at different times of the day and days of the week. When a Control Timer is assigned to a user, the User code will not allow access to any functions during the timers On period. 6. User Name Text Each user can be assigned up to 8 characters of name text. The name text is displayed whenever a code is entered and also when reading the log, making identification of people using the alarm easier. 7. Door Control This option would normally be used for access control. Users are able to open/unlock doors that are assigned to their user code. 8. Proximity TAG As well as or instead of operating the alarm system with a 4, 5 or 6-digit code number, it is also possible to operate it by presenting a Proximity TAG to the keypad (this requires a Proximity keypad). INS177 45

User Types

The User type determines which functions are available to the user i.e. arming, disarming, resetting etc. and also, which options the user can access i.e. Setup Users, System Tests etc. The following User types are available: 1: Master Master users can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Master users can access all User menu options. Master users can also change their own User codes and assign new users to the system. The Master user will also activate any output programmed as Door Strike. 2: Manager Manager users can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Manager users can access all User menu options except Setup Users. Manager users can also change their own User codes. 3: Standard Standard users can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Standard users can access all User menu options except for Setup Users, System Tests, and Change Timers. Standard users can also change their own User codes. 4: Local (Premier 48,88,168,640) Shunt (Premier 24) Local users behave the same way as Standard users. However, Local users can only arm and disarm areas assigned to their codes from keypads assigned to the same areas. Shunt users can omit and reinstate any zone that has been programmed as Shuntable. 5: Duress Duress users behave the same way as Standard users. However, Duress users will activate any outputs programmed as Panic Alarm or Duress whenever their code is entered. 6: Arm Only (Premier 48,88,168,640) Reset Only (Premier 24) Arm Only users can only arm and reset their assigned areas. Reset Only users can only disarm following an alarm and then reset, rearm the alarm again. 7: Door Strike Door Strike users have no access to User functions or Menu options. However, Door Strike users will activate any outputs programmed as Door Strike whenever their code is entered. 8: Vacation Vacation users behave as Standard users. However, Vacation users are automatically deleted the first time that the Master User code (User 01) is used to disarm the system.

T - Lock TAG = PGM2 The Users TAG is disabled whenever PGM2 is active. C - Lock Code = PGM3 The Users code is disabled whenever PGM3 is active (default = during the Entry mode). U - Lock User = PGM4 The Users TAG and Code is disabled whenever PGM4 is active (default = Control Timer 4). O - Open/Close The selected user will report open (disarm) and close (arm) events to an Alarm Receiving Centre every time they arm or disarm.
Some of the following options may not always be selectable or de-selectable.
The following options are available: U - User Menu The selected user has access to the User menu. However, the selected user will only have access to options assigned in User Config. (see page 50 for details). E - Eng. Program (Engineers only) Only Available to Engineers. D - Dual Code The selected user can only access an area when a second User code (with the Dual Code attribute and also assigned to the same area) is entered. Dual Code users will also activate the 1st and 2nd Code output type. V - Vacation The selected user is enabled the first time it is used to disarm the system and can be used as many times as required. However, it will be automatically deleted the first time that the User 01 code is used to disarm. Vacation users will only be deleted by the Master user, once they have been used on the system. S - Door Strike The selected user will activate any outputs programmed as Door Strike, whenever their codes are entered. R - Call Rem. PC The selected user has access to the Call Remote PC option, allowing them to initiate a call to a remote Upload/Download PC (see page 56 for details). C - Duress Code The selected user will activate any outputs programmed as Duress, whenever their codes are entered. O - Open/Close The selected user will report open (disarm) and close (arm) events to an Alarm Receiving Centre every time they arm or disarm.

User Config.

This menu defines which menu options are available to the user when their code is entered. This menu will only be displayed if a Custom User type is selected AND User Menu (User Option: U) is enabled (see page 49 for details). Press

To Program Users, proceed as follows:
R6!#6F!B5=%!%6 "&%FL!W$&*$K
"&%FL!W$&*$! W$&*!-H1
Select a user 11 or use the * key to search
"&%FL!W$&*$! W$&*!,-1
To Program a Code Press #
<=%&*!W$&*!46N&S !!!!!ZZZZZZ

To Assign a TAG Press (

(NN!E(g! %6!W$&*K ,h^&Bi!H h`'L6*%

To Assign a FOB Press %

W$&*!,-!?&'6%&!S (;%:95%&!R&9:;&

Enter the new User code

Press !,0 or
(The code can be 4, 5 or 6-digits long) Press # See next page.

$ to exit.2

A*&$&=%!E(g!^CT!+
Press any of the buttons on the Radio FOB (A confirmation tone will be heard)
Present the TAG to The Prox symbol on the keypad (A confirmation tone will be heard)
Tag importing is not available on the Premier 24. INS177

From Previous page.

W$&*!,-!5*&5$!S !!S!(OOOOOOO!_
Use keys ! - 5 to select/deselect areas then press #
W$&*!,-!E#L&!:$S ^6%!:=!W$&
Use keys ! - 5 to select a User type or use the * key to search (Refer to page 45 for a list of available User types)
W$&*!,-!E#L&!:$S "%5=N5*N
Press #2 These options are only displayed if a Custom User type is selected Press * to scroll through options and press $ to select the option (Letter = option IS selected, Star = option is NOT selected).
(*':=> S(!R!C!O!O!O!O!8
W$&*!,-!CL%:6=!, !(!R!C!O!O!O!O!8
Press # to select Options 2 and press $ to edit
(;;&$$!W$&*!@&=F SW!O!O!O!O!O!O!C
W$&*!,-!CL%:6=!H !W!O!O!O!O!O!O!C
Press # to select Config and press $ to edit (The following option is only displayed if User Menu has been selected, see above)
4I5=>&!CB=!46N& S4!V!O!O!O!<!O!O
Press # when finished Press #
W$&*!,-!Q6;U&NS \#!%:'&*77777777
W$&*!,-!46=D:>7 !4!V!O!O!O!<!O!O
Use keys ! - 5 to select a timer if required then press #

W$&*!,-!^5'&!:$1

Press $ to edit the User name text, press # when finished (For details on programming text please refer to page 51). Press #2

INS177 53

This option is only displayed if a User with the Door Strike attribute is selected
W$&*!,-!R66*!4%) !!S!OOOOOOOO!_
Use keys ! - 5 to select/deselect doors then press #
Press ! to assign TAG 0 to import or $ to ignore TAG programming
Present the TAG to the Prox symbol on the keypad (A confirmation tone will be heard) Press + when finished Press ) to exit the menu The display will return to normal.
Tag importing is not available on the Premier 24.

Deleting Users

To delete User codes proceed as follows:

Ensure that Setup Users is selected, the display should look like this:
Select a user 11 then press #2

Press )

R6!#6F!B5=%!%6 R<Q<E<!W$&*!,3
Press # to confirm deletion of the selected User code Press + when finished Press ) to exit the menu The display will return to normal. 54 INS177

Setting up the Part Arms

When a Part Arm 1, 2 or 3 is selected, pre-programmed zones are omitted to allow access to certain parts of the building. This option allows these zones to be programmed or altered by any User that has access to the Omit menu.
To set up the Part Arms, proceed as follows:
Enter a valid User code 1111, the display should look like this:
R6!#6F!B5=%!%6 ()%&*!A5*%!(*'$K
86*!A5*%!(*'!, V6=&!--,!:$!S!C^
Press % to select Part Arm 1 Press & to select Part Arm 2 Press ' to select Part Arm 3
86*!A5*%!(*'!H V6=&!--,!:$!S!C^
86*!A5*%!(*'!H V6=&!-,-!:$!S!C^
Press $ to turn zone ON or OFF for the selected Part Arm
86*!A5*%!(*'!H V6=&!-,-!:$!SC88
Repeat for other zones Press + when finished Press ) to exit the menu The display will return to normal. INS177 55

Calling a Remote PC

This option is used to initiate a call to a remote uploading and downloading computer.
To send a call to a Remote PC, proceed as follows:
R6!#6F!B5=%!%6 45))!?&'6%&!A4K
45))!J5;U!^67,1 -,H203G/be-
Use keys ! - , to select a Call Back number (i.e. 0 = Call Back number 2)
45))!J5;U!^67H1 -,H203G/be-
Press # to start the call back Press ) to exit the menu The display will return to normal.
Altering the Holiday Dates (Premier 48/88/168 only)
This option is used to alter the programmable Holiday Dates. These dates can be used to prevent the control timers from operating on certain dates of the year (bank holidays etc.) or to only operate on certain dates (reminders).
To alter Holiday Dates, proceed as follows:
R6!#6F!B5=%!%6 ()%&*!Y6)7!R5%&$
Y6):N5#!R5%&!,S !!!!--.--.--
Use * to Select a Holiday Date from 1 to 8
Y6):N5#!R5%&!2S !!!!--.--.--
Press $ then enter the new date 8877992
Y6):N5#!R5%&!2S !!!!H0.,H.-H
Press # to accept the new Holiday Date Repeat for other holiday dates Press + when finished Press ) to exit the menu The display will return to normal.
Adjusting Speaker Volumes (Premier 48/88/168 only)
This option is used to adjust the volume level of speakers that are connected to the control panel, keypads and expanders.
To adjust speaker volumes, proceed as follows:
R6!#6F!B5=%!%6 (N]F$%!X6)F'&$K
A5=&)!X6)F'& !!!)&9&)!h!G
Press * to select a Panel, Keypad or Expander speaker
P&#L5N!-2!X6)F'& !!!Q&9&)!h!0

Press $ then ! - 5 to enter a volume level (1 = Minimum, 8 = Maximum) Press & to hear the new volume level
P&#L5N!-2!X6)F'& !!!Q&9&)!hS/
Press # to accept the new speaker volume Repeat for other speakers Press + when finished Press ) to exit the menu The display will return to normal. 58 INS177

Printing the Event Log

If a printer or terminal is connected to the control panel, this option can be used to print out events from the systems Event Log.
To print the Event Log, proceed as follows:
R6!#6F!B5=%!%6 A*:=%!<9&=%!Q6>K
^F'\&*!6D!&9&=%$ !!!!!S!--3-
Enter the number of required events 1111
^F'\&*!6D!&9&=%$ !!!!!S!-3--
Press # to print the Event Log Press ) to exit the menu The display will return to normal.
Editing a Mobile Telephone Number
If the control panel has been programmed to send SMS text messages to a mobile phone in the event of an alarm occurring etc. this option allows the mobile telephone numbers to be programmed.
To edit a Phone Number, proceed as follows:
R6!#6F!B5=%!%6 <N:%!AI6=&!^67K
E&)&LI6=&!^67!,S !4(^!^CE!4Y(^g<
Press * to select the required number
E&)&LI6=&!^67!2S
Press $ to edit the number
-/be-,H203G !!!!!!!!!!!cS,H2
Enter the required mobile phone number then press #
Premier 8 Series Master User Guide

Specifications

5. Specifications

European Standards

Conforms to European Union (EU) Low Voltage Directive (LVD) 73/23/EEC and ElectroMagnetic Compatibility (EMC) Directive 89/336/EEC The CE mark indicates that this product complies with the European requirements for safety, health, environmental and customer protection. This equipment is designed to enable an intruder alarm system in which it is installed to comply with the requirements of security grades 1 or 2 of EN 50131-1 and EN 50131-6 and is suitable for installation in any indoor environment.

Warranty

All Texecom products are designed for reliable, trouble free operation. Quality is carefully monitored by extensive computerised testing. As a result the control panel is covered by a two-year warranty against defects in materials or workmanship. As the control panel is not a complete alarm system but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the control panel failed to function correctly. Due to our policy of continuous improvements Texecom reserve the right to change specification without prior notice. Premier Keypads and Expanders are protected by UK & International Registered Design. Registered Design Number: 2089016 and 3004996. Premier is a trademark of Texecom.

Installation Records

6. Installation Records
No. Description Exit Time
Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec. Sec.

Entry Time 1

Entry Time 2

Bell Delay

Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min. Min.

Bell Duration

Abort Time
RKP No. Keypad Location Keypad Area Quick Arm Emergency Keys PA Fire Med
Zone No. Zone Description Zone Type Zone Areas Zone Omit Part Arms 3
Tick Zones Included in Part Arms
Zone No. Zone Description Zone Type
Zone Areas Zone Omit Part Arms 3

User Codes

User 01 Name Type Master Default 5678 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A New Code Area Time Lock
Installation Company Details
Installation Engineer: Installation Company: Address:
Telephone Number: Installation Date:

Service Record

Date Serviced Comments Engineer
Emergency Telephone Numbers
For 24 Hour Call Out For Anti-Code Reset

Control Panel

Details Model Location Premier 24 ! Premier 48 ! Premier 88 ! Premier 168 !
TEXECOM LTD. 2008 INS177-6

3: Install the Keypads and Zone Expanders
Mount and connect the keypads, zone expanders and output modules to the control panel (see page 12 for wiring details).
4: Install the Alarm Detection Devices
Install the detection devices, PIRs, Contacts, PA Buttons etc. and connect them to the control panel (see page 19 for wiring details).
5: Install the External Sounder
Install the external sounder and connect to the control panel (see page 20 for wiring details).

6: Other Wiring

Complete all other wiring including speakers, telephone line and output connections etc. (see pages 20 - 21 for details).
7: Applying Power to the Control Panel
Once steps 1 to 6 are completed, power can be applied to the control panel. When applying power for the first time, the factory default settings must be loaded (see page 25 for details). Power should always be connected in the following order:
Connect the red battery lead to the positive terminal of the battery and then connect the black battery lead to the negative terminal The panel will only become live when the AC Mains is connected or the Battery Kick-start button is pressed.

Connect the AC mains

For a complete list of factory default settings, see page 28.
8: Programming the Control Panel
Please refer to section 5 for instruction on programming the control panel.

9: Testing the System

Test the system thoroughly to ensure that all features and functions operate as required (see page 84 for details).

Control Panel Layout

Box Tamp

Kick Start

JP2 Network 2 1Amp

Network 1 1Amp

Aux 12v 1Amp

Load Defaults

Jp9 Engineer Remote

Expansion

V 1 00mA =

Bell/Strb - 1Amp

Tx1 Rx1

Tx2 Rx2

Heartbeat

Control Panel PCB Layout

Com 2 Com 1

Networ k 2 1Amp

Networ k 1 1Amp
Aux 12v 1A mp Load Defaults

Premier 48, 88 and 168

V 100mA = 1 Amp

Expansion Heartbeat

F4 Fault Tx Rx F6

Engineer Remote

Rx F10

Rx F11

Rx F12

V 100mA =

Installation 1: AC Input Connected to the 16.5V transformer. DO NOT CONNECT THE MAINS SUPPLY TO THE AC INPUT TERMINALS ON THE PCB. 2: Battery Connections A 12V rechargeable battery must be connected to these terminals in order to provide continuous system operation in the event of an AC Mains failure (see page 11 for details). 3: Digicom Power & Inputs These terminals provide unfused power; remote reset and line fault inputs and are normally used for connecting a stand-alone communicator to the control panel (see page 21 for details). 4: Digicom Outputs Outputs 1 to 8 are low current (100mA -ve applied) and would normally be used when connecting a stand-alone communicator to the control panel (see page 21 for details). Each output is fully programmable (see page 58 for details). 5: Engineers Keypad A portable Engineers keypad can be plugged on here to allow easier access for programming and testing. When using a keypad as an Engineers keypad, the address must be set to 10 (see page 14 for details). The keypad zones and lid tamper are not monitored. 6: Network Data Connections Networks 1 & 2 provide connection for the keypads and zone expanders (Network 2, Premier 168 only). The + and terminals provide power whilst the T transmits data and R receives data (see page 12 for details). 7: Auxiliary 12V Power These terminals are for connecting devices that require 12V power (protected by a 1A fuse). 8: Programmable Zones 1 - 8 These terminals provide the connections for the zones (see page 19 for wiring details). Each zone is fully programmable (see page 33 for details). 9: External Sounder Connections These terminals are used for connecting to an external sounder unit (see page 20 for details). 10: Auxiliary Tamper Connections These terminals can be used for monitoring the tamper loop of an auxiliary device (see page 20 for details). 11: Loudspeaker Connections These terminals can be used for connecting up to one 16 or two 8 loudspeakers (see page 20 for details). 12: Panel Outputs Outputs 1 & 2 are 500mA -ve applied, outputs 3 & 4 are 500mA +ve applied and output 5 is a clean contact relay (see page 21 for wiring details). These outputs are all fully programmable (see page 57 for details). Panel outputs 3, 4 and 5 are only available on the Premier 88, 168 and 640. 13: Plug-on Communicator Connections This socket provides connection for Premier plug-on communicator (see page 22 for details). 14: Box Tamper Connection The box tamper micro switch is connected here. The micro switch provides tamper protection for the main control panel in case of unauthorised access. To disable the box tamper, remove the micro switch lead and fit a jumper link across the two pins.

Premier 48, 88, 168 & 640 Installation Manual 15: Plug-on RedCARE/Dualcom Connections These pins provide connections for a plug-on RedCARE, Dualcom, Digicom or RM8 Relay module. Each output is fully programmable (see page 58 for details). When a device is plugged on to these pins, not all outputs may be available, please refer to the relevant documentation for details. 16: Battery Kick-start Button When powering up the panel without AC Mains present, this button must be pressed in order to connect the battery. If AC Mains is present this button does not need to be pressed. 17: Communication Port s Com Port 1 is a serial communications port and can be used for connecting a PC running Wintex or any supported serial device to the control panel (see page 73 for details). Com Port 2 is a serial communications port and can be used for connecting a PC running Wintex or any supported serial device to the control panel (see page 73 for details). Com Port 3 is a serial communications port and can be used for connecting a PC running Wintex or any supported serial device to the control panel (see page 73 for details). 18: Network Data Indicators The red LED indicates that data is flowing out of the control panel and normally flashes very quickly. The green LED indicates that data is flowing into the control panel and normally flashes slowly, the green LED flashes faster as more devices are connected (see page 12 for details). 19: Load Defaults Button Press and hold this button whilst applying power to the control panel to load the factory default settings. Press and hold this button for 7 seconds with power already on the panel to restore just the Engineer code to the factory setting of. Loading the factory defaults can take up to 60 seconds to complete. Loading defaults will only be possible if the NVM has not been locked (see page 46 for details). For a complete list of factory defaults, see page 28. 20: Expansion The Expansion Port can be used for connecting a 60XPiD Zone Expander (see page 16 for details) or an AV Module (see page 23 for details). 21: Heartbeat LED/Power Light Flashes steadily to indicate that the control panel is functioning correctly. If the light is ON or OFF all the time, then there could be a problem (see page 25 for details). 22: Current Reading Pads To calculate the current draw of the control panel, measure the voltage across the two pads and multiply by 10 i.e. Reading = 34mV (x10) = 340mV = 340mA. 23: NVM 1 & 2 All system programming data and the event log is stored in one or two removable non-volatile memory devices.

wiring details)

Check that the User code has been assigned to the correct area(s) (see page 80 for details) If a Local User code is being used (see page 82 for details) ensure that the keypad being used is assigned to the correct area (see page 53 for details)

Communicator

The Communicator will not dial By default the communicator is disabled, check that the
communicator is enabled (see page 68 for details)
Check that the telephone line has been correctly wired to the communicator (see page 22 for wiring details) Check that the telephone numbers are programmed correctly (see page 67 for details) Check that the account numbers are programmed correctly (see page 67 for details) Check that the dial attempts are not programmed as zero (see page 67 for details) Check that the reporting areas have been programmed correctly (see page 67 for details) Check that the reporting options have been programmed correctly (see page 67 for details)
Communicator dials but does not communicate Check that the telephone numbers are programmed
correctly (see page 67 for details)
Check that the correct protocol is programmed (see page 67 for details)

Factory Defaults

Reset and Service Messages
When the system requires attention because of a potential problem, the display will show one of three service messages. These messages can also be accessed at any time, allowing the user to view installer information. These messages would normally be programmed with the telephone numbers of the installer or the Alarm Receiving Centre (see page 49 for details). To display the service messages, proceed as follows: The display will normally show the time and date:

Fault Messages

The number of devices connected to the networks has changed from the last time a Confirm Devices was done. There is a Mains failure (the keypad may chime every minute, enter a valid code to stop the chime). The display will automatically clear when mains is reapplied. There is a Phone Line fault (the keypad may chime every minute, enter a valid code to stop the chime). The display will automatically clear when line fault clears. The service timer has expired indicating that the system requires a service or a fault has occurred that requires attention (the system can normally still be used). Contact your alarm company to advise. The Standby Battery has not been connected, the display will automatically clear after 1 minute. There is a fault with the control panel standby battery.

followed by

for the Service message:

for the Reset message:

for the Anti-code message:

Copying and Pasting

When programming any items i.e. Zones, Timers, Options etc. pressing CHIME at any point will Copy the information that has just been programmed into memory. To program another item using the information in memory, select the item and press PART to Paste the information. Copying and Pasting can only be performed whilst in the same option i.e. if a zone has just been programmed as Guard 1/Omit/Access/Areas-ABC, ALL of that information can be copied into memory so that when another zone is selected, the same information can then be quickly pasted to the other zone. The information held in memory after programming an item can only be pasted into an item of the same type and cannot be used once another option is selected i.e. Zone programming information cannot be pasted into Timers etc.

Other Things to Know

After entering a zone number (step 3), pressing AREA will jump straight to the Zone Areas When programming text, pressing OMIT will jump straight to the predictive Text

5.1 Zone Setup

Yes Enter zone number e.g. 004 = Zone 004 ??? Press NO to edit the zone type No Use hotkeys 1 - 8 to select a zone type or use the SCROLL key to search e.g. 3 = Guard 3 def Yes Reset Yes Press NO to edit the zone attributes 1 No Use keys 1 - 8 to select an attribute or use the SCROLL key to search Press NO to select/deselect the attribute No Yes Reset Yes Press NO to edit the zone attributes 2 No Use keys 1 - 8 to select an attribute or use the SCROLL key to search Press NO to select/deselect the attribute No Yes Reset Yes Press NO to edit the zone areas Use keys 1 - 8 to select an area e.g. 2 = B. Use the AREA key to toggle between areas A to H and I to P
Yes Reset Yes Press NO to edit the zone text No Use keys 0 - 9 to program text the same way that a mobile phone works e.g. 7, 444, 777 = PIR
Yes Reset Yes Press NO to Change the Chime type No Press NO to Change the Chime type No Yes Yes
Premier 48, 88, 168 & 640 Installation Manual 24-Hour Alarm to the Alarm Receiving Centre when using Contact ID reporting. 7 - PA Audible Normally used for monitoring Panic or hold-up alarms. This zone type will cause a Panic alarm if it is activated when the system/area is armed or disarmed. 8 - PA Silent Normally used for monitoring Panic or hold-up alarms. This zone type will cause a silent Panic alarm if it is activated when the system/area is armed or disarmed. 9 - Fire Normally used for monitoring smoke detectors. This zone type will cause a Fire alarm with distinctive fire tone if it is activated when the system/area is armed or disarmed. In addition, the bell output will pulse. 10 - Medical This zone type will cause a Silent alarm if it is activated when the system/area is armed or disarmed. The panel will also report a Medical alarm to the Alarm Receiving Centre when using Contact ID reporting. 11 - 24Hr Gas This zone type will cause an Audible alarm if it is activated when the system/area is armed or disarmed. The panel will also report a 24-Hour Gas alarm to the Alarm Receiving Centre when using Contact ID reporting. 12 - Auxiliary This zone type will cause a Silent alarm if it is activated when the system/area is armed or disarmed. The panel will also report an Auxiliary alarm to the Alarm Receiving Centre when using Contact ID reporting. 13 - Tamper This zone type will cause an Internal alarm if it is activated when the system/area is disarmed and will cause an Intruder alarm when the system/area is armed. 14 - Exit Terminator This zone type is used to finalise the arming procedure when arming the system/area (see page 38 for details). 15 - Moment Key This zone type can be used to arm and disarm one or more areas. When the zone is activated and then secured the areas assigned to the zone will arm. When the zone is subsequently activated and then secured the system will disarm the areas assigned to the zone. Tamper faults will not arm or disarm anything, but will cause a Tamper alarm. 16 - Latch Key This zone type can be used to arm and disarm one or more areas. When the zone is activated, the areas assigned to the zone will arm. When the zone is secured, areas assigned to the zone will disarm. Tamper faults will not arm or disarm anything, but will cause a Tamper alarm. 17 - Security This zone type can be used to Lockout keypads. When the zone is activated, keypads assigned to the same area will not accept any key presses. When the zone is secured, all keypads respond as normal. 18 - Omit Key This zone type will isolate any zone assigned to the same area as long as it has the Omit attribute. 19 - Custom This zone type can be programmed to operate as required using its own set of attributes (see page 36 for details).

Zone Types

Each zone must be programmed before it is recognised by the system. Zone numbers are entered as a three digit number i.e. Zone 1 would be entered as 001. Each zone consists of a zone type, attributes, areas and zone text. When programming zones, first select a zone type then select any required attributes, assign the zone to an area and then program any required zone text. Zone Type + Zone Attributes + Zone Areas + Zone Text = Zone Programmed. The following zone types are available: 0 - Not used A zone that is not monitored by the system, unused zones should be programmed as Not Used or linked out. 1 - Entry/Exit 1 Normally used for the main entry/exit door i.e. Front Door. The zone can be activated during the exit mode without causing a Fault. Once the system/area is armed, activation of the zone will start the Entry 1 Delay timer for the selected area. If an Entry/Exit zone type is omitted, Guard Access zones in the same area as the omitted Entry/Exit zone will automatically become Entry/Exit 1 zones to allow access into the premises without causing an alarm. If an Entry/Exit 1 or 2 zone type is assigned the Entry/Exit 2 attribute (see page 35), when a zone with the Guard attribute activates and causes an alarm (when the area is fully armed), the zone will become a Guard zone for the duration of the Abort timer. 2 - Entry/Exit 2 Normally used for another entry/exit door that requires a different entry delay i.e. Back Door, Garage Door etc. The zone can be activated during the exit mode without causing a Fault. Once the system/area is armed, activation of the zone will start the Entry 2 Delay timer for the selected area. 3 - Guard Normally used for detection devices such as PIRs, Door Contacts etc. This zone type will cause an Intruder alarm if it is activated when the system/area is armed. This zone type will also activate any output programmed as Guard Alarm. 4 - Guard Access Normally used for detection devices along the entry/exit route. This zone type will allow the user to walk past the detector without causing a Fault during the exit mode or an Intruder alarm during the entry mode, however, the zone will cause an immediate Intruder alarm if activated at any other time. This zone type will also start the entry mode when the system/area is part armed and activate any output programmed as Guard Access Alarm. 5 - 24Hr Audible This zone type will cause an internal alarm if it is activated when the system/area is disarmed and will cause an Intruder alarm when the system/area is armed. The panel will also report a 24-Hour alarm to the Alarm Receiving Centre when using Contact ID reporting. 6 - 24Hr Silent This zone type will cause a silent alarm if it is activated when the system/area is disarmed and will cause an Intruder alarm when the system/area is armed. The panel will also report a

These timers control various timing and delay functions. Each timer can be programmed for any value between 000 and 999. 1 - Exit Settle Time When using the Entry/Exit or Exit Terminator arming mode, some detectors along the exit route can remain active for a number of seconds following activation. This timer ensures that the detectors are given time to deactivate before the system/area arms. 2 - Global Bell Dly. This timer controls the delay between an Intruder alarm occurring and the Bell/Strobe output activating. 3 - Global Bell Dur. This timer controls the duration of the Bell output after an alarm has occurred and any programmed Global Bell Delay time has expired. 4 - Double Knock Dly If a zone has the Double Knock attribute an alarm will only occur if the zone activates twice within this time window or once for the duration of this time window. If multi knocks has been set up (see page 48 for details) the zone may have to be activated more than twice. 5 - Beam Pair Time If a zone has the Beam Pair attribute, an alarm will only occur if another zone with the Beam Pair attribute (assigned to the same area) is activated within this time window. 6 - Activity Delay If a zone has the Activity attribute and it is not activated during this timer and Config. option 14 has been set to View Act. Fault (see page 46 for details), it will be indicated to the user when they try to arm the system/area. 7 - Abort Delay When an Intruder alarm occurs this timer is started, if the area is disarmed within this time window an Abort event will be reported to the Alarm Receiving Centre. If the system is disarmed after this period the Abort event is not reported. 8 - Courtesy Time This timer controls the duration of the Courtesy output type. The courtesy output activates whenever a keypad is being used and during the entry mode. 44
15 - Line Fault Delay This timer controls the delay between a line fault occurring and an audible indication being generated by the system. 16 - AC Off Delay This timer controls the delay between an AC Mains failure occurring and an audible indication being generated by the 17 - Batt Test Period This timer controls the frequency of the dynamic battery test. 18 - Batt Test Time This timer controls how long the dynamic battery test is carried out for. 19 - Soak Test Time This timer controls the number of days a zone with the Test attribute will remain on test for. 20 - Service Interval This timer controls the frequency of the Service Required condition occurring. 21 - Test Call Every This timer controls how often a test call is made to the monitoring station. 024 = daily etc. 22 - Min. Random Time This timer controls the minimum length that the Random output attribute will activate for. of time

Programming Outputs

When programming outputs, select an output group and an output type from that groups list (each output group has its own output types) then select attributes (if required). Output Group + Output Type + Output Attributes = Output Programmed.

Output Group - Not Used

Only the following output type is available: Not Used (off) This output type never activates.
Premier 48, 88, 168 & 640 Installation Manual 16 - Digi Successful This output type activates when the plug-on communicator successfully reports to the Alarm Receiving Centre and deactivates the next time the communicator is triggered. 17 - Digi Active This output type activates when the plug-on communicator is triggered and deactivates when the communicator shuts down. 18 - UDL Lockout This output type activates when an attempt is made to upload/download with incorrect site details more than three times and deactivates after 4 hours or after a valid User code is entered. 19 - UDL Call Active This output type activates when an upload/download is started and deactivates when the upload/download finishes. 20 - UDL Enabled This output type activates when Enable UDL/Engineer is enabled and deactivates when Enable UDL/Engineer is disabled (see page 83 for details). 21 - Confirmed Alarm If the system is already in alarm, this output type activates when a different zone (in the selected area) is activated and deactivates when the alarm is reset. 22 - Custom1 Stage A This output type operates when Custom Output 1 Stage A activates and deactivates when Custom Output 1 Stage A deactivates. 23 - Custom1 Stage B This output type operates when Custom Output 1 Stage B activates and deactivates when Custom Output 1 Stage B deactivates. 24 - Custom1 Stage AB This output type operates when Custom Output 1 Stage A or B activates and deactivates when Custom Output 1 Stage A deactivates. 25 - Custom2 Stage A This output type operates when Custom Output 2 Stage A activates and deactivates when Custom Output 2 Stage A deactivates. 26 - Custom2 Stage B This output type operates when Custom Output 2 Stage B activates and deactivates when Custom Output 2 Stage B deactivates. 27 - Custom2 Stage AB This output type operates when Custom Output 2 Stage A or B activates and deactivates when Custom Output 2 Stage A deactivates. 28 - Radio-Pad Failed This output type activates when the radio pad fails to communicate with the Alarm Receiving Centre and deactivates when the radio pad successfully communicates. 29 - Radio Successful This output type activates when the radio pad successfully communicates with the Alarm Receiving Centre and deactivates when the radio pad fails to successfully communicate. 30 - No Radio Signal This output type activates when the Radio-Pads forward signal is lost and deactivates when the signal is regained. 31 - Radio-Pad Lost This output type activates when the Radio-Pad stops communicating with its base station or the control panel and deactivates when communication starts again. INS176

ComIP Address This is the IP Address of the IP Module. ComIP Port This is the Port number of the IP Module. ComIP Gateway This is the Gateway IP Address that the IP Module communicates through. ComIP Mask This is the Subnet Mask number for the IP Module. Polling/SMG Address This is the IP address of a dedicated Polling or SMG Server that the IP Module might need to connect to. Name/SMG Port This is a descriptive name for the IP Module or SMG Port and might be used for authentication purposes. SMS Centre Pri. This is the first SMS centre telephone number that is used by for sending SMS to mobile phones. (Default = 07860 980480). SMS Centre Sec. This is the second SMS centre telephone number that is used by for sending SMS to mobile phones. Modem Setup Stg. If a standard PC modem is connected to Com1 or Com2, it may require a configuration string to make it work properly (please refer to instruction manual of modem being used for details of required AT commands). The Setup string is programmed the same way that TEXT would be programmed and has a maximum length of 16 characters. The setup string does NOT require AT to be entered at the beginning as this is done automatically. Modem Speed This option allows the speed of a standard PC modem connected to Com1 or Com2 to be adjusted. Pad Serial No. This screen displays the Serial number of the Radio-Pad that is connected. Pad NUA This screen displays the NUA number of the Radio-Pad that is connected. Last Call From This screen displays the NUA number of the last Radio-Pad that communicated with the Radio-Pad that is connected to the control panel. FSS:??? (>=004), Forward Signal Strength RSS:??? (>=050), Reverse Signal Strength This screen displays the Radio-Pad Forward (FSS) and Reverse (RSS) Signal Strength of the Radio-Pad that is connected to the control panel. The FSS value should be greater than or equal to 4 and the RSS value should be greater than or equal to 50.

Setup Radio-Pad

Pad ARC 1 Pri No This is the first number that is used by the Radio-Pad for reporting events to ARC 1. Pad ARC 1 Sec No This is the second number that is used by the Radio-Pad for reporting events to ARC 1. Pad ARC 1 Prefix This number will prefix the account number for ARC 1. Pad ARC 2 Pri No This is the first number that is used by the Radio-Pad for reporting events to ARC 2. Pad ARC 2 Sec No This is the second number that is used by the Radio-Pad for reporting events to ARC 2. Pad ARC 2 Prefix This number will prefix the account number for ARC 2. Pad ARC 3 Pri No This is the first number that is used by the Radio-Pad for reporting events to ARC 3. Pad ARC 3 Sec No This is the second number that is used by the Radio-Pad for reporting events to ARC 3. Pad ARC 3 Prefix This number will prefix the account number for ARC 3. Radio-Pad Attempts This is the number of times the Radio-Pad will try to dial the Alarm Receiving Centre telephone number before giving up. The number of dialling attempts is limited to 9. If this value is set to 0, the Radio-Pad will never dial out.

Premier 48, 88, 168 & 640 Installation Manual 6. User Name Text Each user can be assigned up to 8 characters of name text. The name text is displayed whenever a code is entered and also when reading the log, making identification of people using the alarm easier. 7. Door Control This option would normally be used for access control. Users are able to open/unlock doors that are assigned to their user code. 8. Proximity TAG As well as or instead of operating the alarm system with a code number, it is also possible to operate it by presenting a Proximity TAG to the keypad (this requires a Proximity keypad). 9. Radio FOB As well as or instead of operating the alarm system with a code number or Proximity TAG, it is also possible to operate it Using a Wireless Radio Transmitter (this requires a Wireless Radio Receiver keypad).

Default User Codes

When the control panel is first powered up and the factory default settings are loaded (see page 25 for details), only the Engineer code and the Master User code exist. The Factory default Engineer User code is. The Engineer is always User 00. If the Engineer code has been lost or forgotten, it can normally be reset back to the factory default without having to reprogram the entire system (see page 32 for details). Resetting the Engineer code is only possible if the NVM has not been locked (see page 46 for details). The Factory default Master User code is. The Master User is always User 01. If the Master User code has been lost or forgotten, it can be reprogrammed by the Engineer in this menu.

User Types

The User type determines which functions are available to the user i.e. arming, disarming etc. In addition, the User type also determines which options the user can access i.e. Setup Users etc. The following User types are available: 0: Engineer Engineers can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Engineers can access the Programming Menu and all User menu options. Engineers can also change their own User codes and assign new users to the system. The default Engineer User type (User 00) can assign any User types to the system. Engineers can only disarm areas that were armed using an Engineer code. They cannot disarm any areas that were armed with another User code. 1: Master Master users can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Master users can access all User menu options. Master users can also change their own User codes and assign new users to the system. The Master user will also activate any output programmed as Door Strike. 2: Manager Manager users can arm, disarm, omit zones, silence alarms and reset their assigned areas. In addition, Manager users can access all User menu options except Setup Users. Manager users can also change their own User codes. 3: Standard Standard users can arm all the areas assigned to the code and disarm all the areas assigned to the code (even if only one area is in entry or alarm) from any keypad, omit zones, silence alarms and reset their assigned areas. In addition, Standard users can access all User menu options except for Setup Users, System Tests, and Change Timers. Standard users can also change their own User codes. 4: Local Local users behave the same way as Standard users. However, Local users will only arm the area that the keypad is assigned to and disarm the area that is in entry or alarm (provided that the code has that area assigned to it

User Functions and Options
The table below shows the options that are available to each user. All users that have access to the Arming Menu have the ability to View Zone Status, Set Chime Areas, View Act. Faults and View Act. Counts. All users have access to the User Menu have the ability to View Event Log, Adjust Volumes and Print Event Log.

User Options 1

Engineer Arming Disarming Omitting Eng. Reset Disarm First Master Arming Disarming Omitting Disarm First Manager Arming Disarming Omitting Disarm First Standard Arming Disarming Omitting Disarm First Local Arming Disarming Omitting Local Arming Local Disarm Disarm First Duress Arming Disarming Omitting Disarm First Arm Only Arming Door Strike Vacation Arming Disarming Omitting Disarm First Custom -
User Menu Eng. Program Door Strike Call Rem. PC Open/Close User Menu Door Strike
User Menu Call Rem. PC Open/Close

User Menu Open/Close

Duress Code Open/Close

Door Strike -

User Menu Vacation Open/Close

Call Rem. PC Open/Close

User Config.
Engineer Change Code Chime Zones Change Timer System Tests Setup Users Eng. Access Add Eng. code NVM Locking Master Change Code Chime Zones Change Timer System Tests Setup Users Eng. Access Manager Change Code Chime Zones Change Timer System Tests Eng. Access Standard Change Code Chime Zones Eng. Access Local Change Code Chime Zones Eng. Access Duress Arm Only Eng. Access Door Strike Vacation Eng. Access Not Used -
This menu defines which options are available to the user when their code is entered. Press to scroll through the options and press to (Letter = option IS select them or use keys selected, Star = option is NOT selected). The following options are available: A - Arming Areas assigned to the selected user can be armed. D - Disarming Areas assigned to the selected user can be disarmed. O - Omitting Zones assigned to the same areas as the selected user can be omitted, providing that they have the omit attribute assigned to them. R - Eng. Reset (Engineers only) Areas programmed as Engineer reset can be reset after an Alarm has occurred. a - Local Arming The User can only arm areas that the keypad is assigned to. d - Local Disarm The User can only disarm areas that the keypad is assigned to, or areas that are in entry or alarm (provided that the code has that area assigned to it). Y - Auto YES After a User code has been entered, pressing the confirm the next action is not required. key to

User Name Text

Each user can be assigned up to 8 characters of name text. This can be beneficial when reading the log, as identification of people is made easier. See page 32 for details on programming text. Text is programmed in a similar way to mobile phones. Select characters by pressing the corresponding key the appropriate number of times (to select a character on the key to move the cursor along). same key, press the

Door Control

This option would normally be used for access control as it only allows the user to open/unlock doors that are assigned to that user code. Door control is only available to users with the Door Strike attribute assigned to it.

Deleting Users

If a User code needs to be deleted from the system, this must be done, by a user that has access to the Setup Users menu. To delete User codes proceed as follows: Ensure that Setup Users is selected, the display should look like this:

User Time Lock

This option allows the selected user to be denied access to the system at different times of the day and days of the week. When a Control Timer is assigned to a user, the User code will not allow access to any functions during the timer On period (see page 49 for timer programming). The first 4 options (Premier 48) or 6 options (Premier 88/168/640) will lockout the selected user (Code and TAG) when the corresponding control timer is active. The last two options will lock out the selected users TAG (T) when Custom Output 2 Stage A is active or lock out the selected users Code (C) when Custom Output 2 Stage B is active.
Select a user from 1 to 24 (Premier 48), 1 to 49 then (Premier 88) or 1 to 99 (Premier 168) press , the display should look like this:
, the display will look something like this:
Where 15 is the selected User number. Press Press to confirm deletion of the selected User code to exit from Setup Users

5.9 Engineer Utilities

View Event Log
The control panel has two Event Logs, which are time and date stamped. The first log which is a system log, records all events that occur on the system, i.e. Users entering their codes to arm or disarm areas, alarm events, failures to arm etc. and the second log which is an alarm log, only records alarm events that occur on the system.

Do Bell Test

Do Walk Test
Press OMIT to invoke the Engineers Hold Off mode of a Texecom Bellbox
Press YES to walk test all areas or use keys 1 - 8 to select/deselect areas
Use the SCROLL key to select the required test
Press CHIME to select: Chime Once then lockout zone Chime on every activation or No Chime at all Press AREA. to toggle the display between the zones that have been tested and the zones that still need testing To view zones that have not activated recently, enter the number of days required i.e. 007 will show zones that have not activated in the last 7 days
Press YES to test ALL channels or use keys 0 - 8 to select individual channels e.g. 3 = Channel 3 Press YES again to clear ALL channels or use keys 0 - 8 to clear individual channels e.g. 3 = Channel 3
This option allows Allows the Bell, Speaker and various control panel outputs to be tested. The following outputs can be individually tested: Test Bell Test Strobe Test Speaker Test Digi Test Panel Test RedCARE Test Com???? LCD Display User Outputs The Bell output The Strobe output The Speaker output The Hardwired digicom outputs The panel outputs The plug on RedCARE outputs The plug on digi outputs The LCD keypad display Any outputs that have the User Test attribute (see page 62 for details).
Any of the zones on the system can be walk tested to ensure that they operate correctly. A walk test can only be performed when the system or area is disarmed. Once a zone has been activated it will not generate a chime tone again. If however the key is pressed, a zone will chime every time it is activated. The Walk test menu also includes a last activation log that can be recalled when doing a walk test. This log shows zones that have NOT been activated over a period of days. key will firstly show the zones that still need Pressing the key a second time will display the testing, pressing the zones that have not been activated that day, to view zones that have not been activated for 3 days, type in 003 the maximum number of days that can be recalled is 255, pressing the key a third time will revert back to the standard walk test display.
Pressing OMIT at the Bell or Strobe Test will cause the Strobe output to pulse 3 times, invoking Engineers Hold Off mode if a Texecom bell box is connected.

View Zone Status

Do System Tests
Use keys 0 - 9 to enter the required zone number or use the SCROLL key to search e.g. 064 = Zone 64
Use keys 1 - 4 to select an option or use the SCROLL key to search e.g. YES = View Sys. Status
To disable the zone, Press OMIT. To make the zone Chime, Press CHIME To view the zone text, Press AREA
This option allows various control panel features to be tested or reviewed. 1 - View Sys. Status Allows the system voltage and current to be viewed. 2 - View Batt Status Allows the battery voltage and charging status to be viewed. 3 - Test Outputs Allows the Bell, Speaker and system outputs to be tested. 4 - View Version No. This option allows the control panel software version and serial number to be viewed.

(only applicable for custom zone types)

Zone Areas Zone Text

Press I P),
Null Entry/Exit 1 Entry/Exit 2 Guard Guard Access 24Hr Audible 24Hr Silent PA Audible PA Silent Fire to edit, O = Omittable F = Force Omit 1 = Part 1 Omit 2 = Part 2 Omit to edit, D = Double Knock B = Beam Pair S = Soak Test F = Activity to edit, I = Instant Arming P = Part Arming F = Full Disable D = Disarm Only to edit, B = Bell/Strobe I =Internals M = Monitor 24Hr to edit, to accept.
Medical 24Hr Gas Auxiliary Tamper Exit Terminator Moment Key Latching Key Security Key Omit Key Custom to select an attribute, to accept 3 = Part 3 Omit A = Access E = Entry/Exit 2 G = Guard to select an attribute, to accept R = Reset A = Auto Re-arm Q = Quick Resp. E = Eng. Alarm to select an attribute, to accept S = Silent Arming T = Time Arm Disable K = Key Tube to select an attribute, to accept C = Enable Coms W = Warning = all areas, = areas A H and

to select an area, (

to edit, Press number of times),
to select characters (press the required key the appropriate to accept Move Cursor Copy Text to Memory Paste Text from Memory Upper, Lower Case, Predictive Text and Numerical Chime 2 Chime 3

Zone Chime

.,?!1@MNO6 ABC2 PQRS7 DEF3 TUV8 GHI4 WXYZ9 JKL5 0_ Press to alter chime tone, to accept Silent Chime 1
Quick Reference Guide Area Programming Timers
Area Arm Suites Area Suite Text
to select a timer, to enter a value, to accept Premier 48 Premier 88 Premier 168/640 Exit Dly for Areas: A D (1 4) A H (1 8) A to P (9 16) 1: Entry Dly 1 for Areas: A D (1 4) A H (1 8) A to P (9 16) 2: Entry Dly 2 for Areas: A D (1 4) A H (1 8) A to P (9 16) 3: 2nd Entry Dly for Areas: A D (1 4) A H (1 8) A to P (9 16) 4: Bell Dly for Areas: A D (1 4) A H (1 8) A to P (9 16) 5: Bell Duration for Areas: A D (1 4) A H (1 8) A to P (9 16) 6: Coms Dly for Areas: A D (1 4) A H (1 8) A to P (9 16) 7: Part Bell Dly for Areas: A D (1 4) A H (1 8) A to P (9 16) 8: Use to select an area, to select arming an mode, to accept Entry/Exit Instant Exit Term. Deferred Timed Exit to select a suite, no to edit, to select an area, ( = all areas, Use = areas A H and I P), to accept to select a suite, to edit, Use required key the appropriate number of times), to select characters (press the to accept