The disc menu language is not the correct one.
The disc menu language has not been set up. The language of your choice is not available on the disc.
Audio CDs Audio CDs (8 and 12 cm). CD-R, CD-RW Most CD-R (one recording only) and CD-RW discs (rewritable). This player can play most CD-R discs. CD-Rs written during a multisession recording can also be played, provided that the session has ended before the disc is played (depending on the write software). However, depending on the condition of the CD-writer, computer and the disc used, you may find that not all discs will play successfully.When playing a CD-R disc, it is completely normal for the unit to take up to 20 seconds to recognise the disc before starting to play. If the disc is not recognised after a period of 20 seconds, remove the disc, and then insert it again. Irrespective of the actual recording capacity of the CD-R, do not use its full capacity. CD-Rs should be preferably used instead of CD-RWs (rewritable CDs) as, in certain cases, CD-RW playback may be faulty. Use reliable, good-quality CD write software. Close all other applications on the computer to ensure reliable CD-R disc recording. DivX files DivX is the name of a revolutionary new video codec which is based on the new MPEG-4 compression standard for video.Whether DivX files play correctly on your player or not depends on the preparation and production of the audio and video files,the codecs and the type of recording equipment used,as well as on your computers parameters.It is therefore possible that you cannot play a DivX file or that part or all of it is defective.It also sometimes happens that you can play the images (video) but not the sound (audio). DivX disc compatibility with this player is limited as follows:The maximum resolution of the DivX file is below 720x576 (W x H) pixels. DivX filenames should not exceed 56 characters. If the video and audio structure of the recorded file is not interleaved,either video or audio is outputted. If the file is recorded with GMC,the unit supports only 1-point GMC.GMC is the acronym for Global Motion Compensation.It is an encoding tool specified in the MPEG4 standard.Some MPEG4 encoders,like DivX or XviD,have this option.There are different levels of GMC encoding,usually called 1-point,2-point,or 3-point GMC. DivX files with subtitles in.SRT,.SUB and.SMI formats can be played.Correct playback of all languages may not be possible as some characters may be missing. mp3 files CD-R and CD-RW discs containing audio files in mp3 format.With regard to CD-R mp3 discs, please follow all the recommendations for CD-R above, along with the comments below: Your mp3 files should be ISO 9660 or JOLIET format. ISO 9660 format and Joliet mp3 files are compatible with Microsoft DOS and Windows, as well as with Apple Mac.These two formats are the most widely used. mp3 filenames should not exceed 8 characters and should end with the.mp3 extension. General name format:Title.mp3.When composing your title ensure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including (. , / , \ , = ,+). The total number of files on a disc should be less than 999.The total number of folders should be less than 499. Use a decompression transfer rate of at least 128 kB/sec (kilobytes/second) when recording mp3 files. Sound quality with mp3 files basically depends on the rate of compression/ decompression you choose. Obtaining audio CD quality sound requires an analogue/digital sampling rate, that is conversion to mp3 format, of at least 128 kB/sec and up to 160 kB/sec. Choosing higher rates, such as 192 kB/sec or more, only rarely produces even better sound quality. Conversely, files with sampling rates below 128 kB/sec will not play properly. Do not try recording copyright-protected mp3 files.Securized files are encrypted and code-protected to prevent illegal copying.You must not copy such files. WMA (Windows Media Audio) files CD-R with WMA files. WMA filenames should not exceed 8 characters,and should end with the.wma extension.General name format:Title.wma.When composing your title ensure that you use 8 characters or less,have no spaces in the name,and avoid the use of special characters including (.,/,\,=,+). The total number of files on a disc should be less than 999.

Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Important:The above recommendations cannot be taken as a guarantee that the DVD player will play mp3 or WMA recordings, or as an assurance of sound quality.You should note that certain technologies and methods for mp3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (i.e. degraded sound quality and even, in some cases, inability of the player to read the file).
You have forgotten your password (Parental control).
Open the disc tray, press CLEAR and then enter 00001 with the numeric buttons.Turn off the player and then turn it on again.
In accordance with the rating plate of the unit, this unit complies with current standards concerning electrical safety and electromagnetic compatibility.

CAUTION

- LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

Precautions

Use If your appliance has been stored in a cool place for any length of time, during a journey for example, wait for about 2 hours before using it. The openings located on the top and bottom are for ventilation and must not be obstructed. During thunderstorms, we recommend that you isolate the appliance from the electrical supply so that it is not damaged by electrical or electromagnetic surges. This appliance is designed for continuous use. Switching off the DVD player to stand-by mode does not disconnect it from the mains supply.To completely isolate the equipment, remove the plug from the mains socket as some components remain connected to the electrical supply. If you notice any burning or smoke, disconnect the appliance immediately to avoid any risk of electrocution. Do not attempt to look inside the appliance through the disk tray opening or any other opening.You may be electrocuted or exposed to laser radiation. This appliance is for domestic use only and must not be used for industrial purposes. Total or partial copying of recordings protected by copyright legislation, without the explicit permission of the holder of the rights, contravenes current legislation. Copying or downloading music files for sale or any other business purpose constitutes or could constitute a violation of copyright law. Cleaning Use a soft, dry, clean cloth. Regularly dust the vents at the back or sides. Using solvents, abrasive or alcohol-based products risks damaging the appliance. If an object or liquid enters inside the appliance, unplug it immediately and have it checked by an authorised engineer. Handling and caring for discs

CLASS 1 LASER PRODUCT

DVD DTH250E DTH252E DTH255E

User Manual

CAUTION RISK OF ELECTRIC SHOCK - DO NOT OPEN

THE LIGHTNING FLASH AND

ARROWHEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF A DANGEROUS VOLTAGE INSIDE THE PRODUCT.
CAUTION:TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THE EXCLAMATION POINT WITHIN
THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT This THOMSON product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment,at their end-of-life,should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic product. Please, help us to conserve the environment we live in!

HELPLINE

You can contact THOMSON by dialling: 1312 (for United Kingdom, 0.10/mn inc VAT) www.thomson-europe.com

Connections and Setup

Some points to check before you connect your TV set
Ensure that the mains supply in your house complies with that indicated on the identification sticker located on the back of your appliance. Install your appliance horizontally, away from any source of heat (fireplace) or appliances generating strong magnetic or electric fields.The components of this appliance are sensitive to heat.The maximum ambient temperature should not exceed 35 Celsius. Leave sufficient space around the appliance to allow adequate ventilation: 10 cm on either side and at the back, as well as 7 cm above it are ideal. The humidity of the room should not exceed 75%. If you have to use the appliance outdoors, do not expose it to rain or splashing water.The appliance should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on top of it. Moving it from a cold environment to a warm one is likely to cause condensation on some components inside the appliance. Let the condensation disappear of its own accord before turning the appliance on again. Before moving the player, make sure the disc tray is empty.

Front panel controls

SELECT / DISPLAY

SD / MMC / SM

MP 3 VCD MP 4
ON/STANDBY - To switch the appliance on and off. OPEN/CLOSE - To open and close the disc tray. STOP - To stop disc playback. PLAY - To start playing a disc. SELECT/DISPLAY - To choose the card inserted in the card reader. ( DTH250-DTH255)

Handle your discs with care. Hold the disc with your fingers at the edges or through the hole. Insert the disc with the label facing up (for a single-sided disc). Place the disc properly into the tray in the allotted holder. Use a soft cloth to clean discs if necessary, always wiping from the centre to the edge. Always put discs back in their cases after use and store in a vertical position. Do not close the tray with two discs in it or with a disc not sitting correctly in the holder. Do not play cracked, chipped or warped discs nor try to repair them with adhesive tape or glue. Do not write on a disc. Do not move the player when a disc is being played. Do not scratch discs or store them in places exposed to direct sunlight, high humidity or high temperatures. Do not use aerosol cleaners, benzene, anti-static liquids or any other solvent for cleaning discs.When cleaning, wipe gently with a soft damp (water only) cloth from the centre to the edge, avoiding circular motions, which could cause scratches and interference during playback.
To display the Status menu. (DTH252)
SD/MMC/SM - MS - CF - Memory card readers. (DTH250-DTH255)
Basic connections (DVD player + TV + video recorder)
Please refer to the extra connection sheet for different connection options.
1. Connect the DVD player Scart socket (TV AUDIO VIDEO OUT) to the television sets
Scart socket (AV1, EXT1,AUX1) using a Scart lead (not provided). - OR 1. If your television set does not have two Scart sockets, connect the DVD player to the video recorders AV2 socket using a Scart lead (not provided). If you have a satellite or cable receiver you can also connect the DVD player to the receivers second Scart socket.
Note: If your video recorder only has one Scart socket, but has a modulator, use the aerial cable to connect the video recorder to the television set, adjust the video recorders modulator, then connect the DVD player to the video recorders Scart socket.

The remote control

ZOOM To access the Zoom function. ANGLE To access the Camera angle function. OPEN.CLOSE To open and close the disc tray. To switch the appliance on and off. PROGRAM To access the Program menu. RANDOM To access the Random playback function. REPEAT/A-B To access the Repeat playback function and A-B repeat playback. HDMI For adjusting the digital signals from the HDMI socket. REV To start reverse accelerated play and reverse slow motion. FWD To start forward accelerated play and forward slow motion. SKIP / To start a reverse or forward search for a chapter or track. PAUSE To activate freeze frame, frame advance, slow motion. PLAY To start playing a disc. STOP To stop play. CLEAR To clear entered items in a menu. DISC MENU To call the disc menu (if there is one). To access the PBC menu. To navigate through the menus. OK To confirm a selection. PREVIEW To access the Digest or the Introscan function. SET UP To access the players menu. 0-9 Number entry. DISPLAY To display the Status menu. AUDIO To change the dialogue language or audio format. SUBTITLE To select a subtitle language and turn the subtitle menu on and off. To mute and restore the sound. BOOKMARK To access the Bookmark function. TITLE MENU To access the title menu of the disc (if there is one). To turn the PBC function on and off.

Note: If your television set only has one audio socket connect it to the DVD players left socket (white).

Discs you can play

In spite of progress made to ensure playability of all discs types, it is not possible to guarantee playback of discs which are not in conformity with DVD, CD,VCD or SVCD standards.This unit may not play some recordings or files on CD-R, CD-RW, DVD-R, DVD-RW, DVD+R, DVD+RW due to differences in recording formats, software used and disc types.

Note on DivX files

Before playing DivX or mpeg4 files, please be sure of their origin and that you have legally purchased or rented the contents. Pirate copying is illegal and may result in sanctions. Private copies of your own material for your own use may be legal in some countries. Make sure you are aware of any applicable laws. DTS - is a digital sound compression technique developed by Digital Theater Sound Systems for digital audio multichannel signals.DTS and DTS Digital Out are registered trademarks of Digital Theater Systems inc.
DVD-Video Digital video discs - 12 cm and 8 cm, single or double sided, single or dual layer. DVDs are high-density optical discs on which high quality picture and audio are recorded by means of digital signals. DVD-R, DVD-RW, DVD+R, DVD+RW Most DVD-R and DVD+R (one recording only), DVD-RW and DVD+RW discs (rewritable). Depending on the DVD writer and discs used. Recordings using DVD-R and DVD-RW discs must be made in Video DVD mode. Recordings using DVD+RW discs must be made in accordance with the specifications for DVD+RW discs with a 4.7 GB capacity. VCD - Video Compact Disc CD on which you can record up to 74 min. of VHS-quality video associated with still images, audio tracks and interactive menus. SVCD - Super Video Compact Disc Most SVCDs comply with the IEC62107 standard. SVCDs can be used to record up to 70 minutes of digital sound and images in accordance with MPEG-2 standards for video and MPEG-1 standards for audio. 4
Component output (Y, Pr, Pb / Y, Cr, Cb) YPrPb sockets deliver an optimum image quality due to the separation of the video signal into three separate components (comparable with RGB separation in a Scart-Peritel cable).

Note: the video signal available from these 3 sockets depends on the choice made in the Video Out menu.

Technical data

Power requirements:AC 230V, 50 Hz Power consumption: 15W Operating temperature: 5C to 35C (41F to 95F) Operating humidity: 5 % to 90 % (no condensation)

RCT195DB1

In order to obtain the best possible image quality, always use very high quality cables for the connections.Your dealer can provide Y, Pr, Pb cables that are sold together and come in the standard colour codes (green, red and blue) used for these types of sockets and cables.
Note: do not forget to also connect the audio cables, because Component cables only transmit images, and not sound.

DVD+Rewritable

THOMSON Multimedia Sales Europe 46, quai A. Le Gallo 92648 Boulogne Cedex FRANCE 464 RCS NANTERRE http://www.thomson-europe.com 35905170 Copyright THOMSON 2005

August 2005 ed.

Inserting batteries in the remote control Insert two LR06 or AA batteries in the remote control.
Do not mix different types of batteries or new and old batteries. Do not use rechargeable batteries. In order to avoid any risk of explosion, observe the polarities indicated inside the battery compartment. Replace only with the type of batteries specified above. Do not dispose of them in a fire or recharge them. If you are not using the remote control for a long period of time, remove the batteries. Please respect the environment and prevailing regulations. Before you dispose of batteries or accumulators, ask your dealer whether they are subject to special recycling and if they will accept them for disposal.
Optical and coaxial Out sockets The digital sound from a Video DVD in playback is permanently available at the optical and coaxial sockets on your player. Use one of these sockets by connecting it to a decoder or a DTS or Dolby Digital amplifier. Some of these appliances are equipped with a coaxial In socket (COAXIAL) or an optical In socket (OPTICAL), while others are equipped with both sockets. Choose one of the two connections. 1
Note: In most cases these two types of connection give similar results; the only difference lies in the type of cable used and the cost of these cables, the coaxial cable being the least expensive one to buy. However it sometimes happens that some coaxial cables are parasitised by high frequency interference caused by household electrical appliances, high voltage electric cables or radio transmitters. Note : when connecting the optical audio digital cable: 1. Remove the protection cap from the connector and connect it firmly as shown on the drawing. 2. Keep the protection cap and always reattach the cap when the connector is not in use, to keep it dustfree.

Programme playback (DVD,VCD and audio CD)
With this option, you choose and programme the playback order. You can store up to 20 tracks.
Playback of mp3,WMA, JPEG and DivX files
mp3 is an audio file format which compresses recorded music. It was developed in collaboration with.The main advantage of the mp3 format is that it means CDquality music tracks can be stored on a personal computer in user-friendly compressed files. WMA (Windows Media Audio) is another audio file format developed by Microsoft. JPEG files are image files. Make sure that they have a resolution of less than 5 megapixels. Your player is an Official DivX Certified product that plays DivX5, DivX4, DivX3, and DivXVOD video content, in compliance with DivX Certified technical requirements.
1. Insert a disc. 2. In Stop mode, press the PROGRAM button.The Program menu appears. 3. Use the number buttons to enter the title number and then the chapter number (for
DVD) or the track number (for VCD and Audio CD). Repeat Step 3 as often as necessary.
TV Type In addition to PAL DVDs and VCDs, you can enjoy NTSC films as well (a 50Hz or 60Hz PAL compatible TV set is required). If the pictures from the DVD being played appear in black and white on your screen, try changing the colour standard. Set the function to PAL or NTSC and press OK to confirm. Video Out Choose the type of video signal that the TV or monitor connected to the back of your player will accept. RGB: this gives the best quality picture output from the TV AUDIO VIDEO OUT SCART socket. YUV Interlace: used when a YCrCb monitor is connected to the 3 component video sockets. YUV Progress.: used when a YPrPb monitor is connected to the 3 component video sockets.
Note : the composite (CVBS) video signal output from the TV AUDIO VIDEO OUT SCART socket remains available whatever selection has been made.

HDMI (DTH252-DTH255)

Use the HDMI button on the remote control to start, adjust or stop this function. Press repeatedly on the button to adjust the digital signals, according to the device connected to the HDMI socket.

4. Use the

, , and buttons to select Start and press OK to start playback. Tracks are played in the order of the playback list. Playback stops once all tracks have been played.
Displaying JPEG files or playing mp3 or WMA or DivX files
Before inserting a disc, check that it is compatible with the player. 1. Open the tray by pressing the OPEN/CLOSE button. 2. Place the disc with the printed side facing up and close the tray.The discs contents are displayed. 3. Select a folder using the and buttons on the remote control, then press OK to see the folders contents. 4. Select a file using the and buttons on the remote control, then press OK to start playback. 5. Press the STOP button to stop playback. 6. To go back to the folder list, press the button in stop mode.

Note: During playback you can use the SKIP or SKIP button to go back to the previous file or go on to the next one. ZOOM : press ZOOM for the ZOOM function, then press REV or FWD until you reach the zoom size you want.
Basic Playback Operations

Regional coding

Your DVD player has been designed to process regional management information that is stored on DVD discs. DVD discs that have different regional codes to that of your player cannot be played.The regional code for your player is 2 (Europe, the Middle East, South Africa, Japan).ALL means all regions.When you buy a disc check that it bears the correct logo.
5. Press the STOP button to stop the programme playback. Press the STOP button twice
or the OPEN/CLOSE button to cancel the programme playback.
Random playback (all discs except DVD)
You can play all the tracks on the disc in a random order (chosen by the player).
Operating the DVD player 1. Switch on your TV set. 2. Press the button on the remote control or the ON/STANDBY button located on
the DVD players front panel.
1. Insert a disc. 2. Press the RANDOM button during playback.Random appears. Playing stops when all

tracks have been played.

Menu Language To change the language of the player menus, choose the language using the buttons and press OK to confirm.
The Dolby Digital Setup menu ( see Appendix)
Dolby and the double-D symbol license from Dolby Laboratories. are trademarks of Dolby Laboratories. Manufactured under
3. Press the RANDOM button again to stop random playback. Off appears on the TV

screen.

Playback 1. Press the OPEN/CLOSE button on the front of the appliance or on the remote control

to open the disc tray.

Advanced functions
Audio (DVD,VCD and audio CD)
Some discs have several audio tracks used for different languages or different audio formats. To change the language or audio format during play, press the AUDIO button one or more times to select one of the available audio formats or languages.
Note:This option is only available if the disc offers a number of dialogue languages or audio formats.

DivX subtitles

In order to display properly subtitles in some Eastern European languages, you need to select the correct character set. During DivX playback,press several times the TITLE/MENU button on the remote control to choose a character set: Czech, Slovak, Hungarian, Polish or Default (for Western European languages).
2. Put the disc in with the printed side upwards (in the case of a single-sided disc). 3. Press OPEN/CLOSE again to close the disc tray. Play starts automatically. If a menu
appears, one of its options can be selected to start playing the disc. Select it and press OK.
Dynamic You can use this function to control the different sound levels via dynamic compression. It improves the quality of the sound track at a low volume and quietens the loudest sounds. Select an option using the and buttons, and press OK to confirm.

Note:This function is available only on DVD discs recorded in Dolby Digital.
Playing JPEG and mp3 music files at the same time
You can display JPEG files while listening to mp3 music files recorded on the same disc. 1. Insert the disc containing the two types of file in the player. 2. Select an mp3 music file using the and buttons, then press OK to confirm your selection. 3. Then select a JPEG image file using the and buttons, then press OK to confirm your selection.
Note:To delete your selection, press the CLEAR button.
4. Press STOP to stop playback.
Notes:The player stores the point where playback was interrupted. If you press PLAY again, playback resumes from this point.To stop playback completely or to start again from the beginning, press STOP twice. If the player is left in STOP mode for a few minutes without any user interaction, a screen saver is activated.
The Preferences Setup menu
Note:The Preferences Setup menu is not available when there is a disc in the player.

Bookmarks

The player can store up to 12 disc locations as long as the disc remains in the player and the unit remains switched on.

Accelerated play

While the disc is playing, press the REV or FWD button one or more times to vary the speed and direction of the accelerated play.
1. Press the BOOKMARK button during play.A menu is displayed. 2. To create a bookmark, select a free bookmark using the and

PLAY button.

Audio To change the dialogue language, choose the language using the press OK to confirm. Subtitle To change the subtitle language, choose the language using the OK to confirm.

buttons and

buttons and press the

Still image

While the disc is playing, press PAUSE once for freeze frame.
Note: after a few minutes in PAUSE with no user interaction, the player goes to screen saver mode.
3. Repeat Step 2 as often as necessary. 4. To start playback from a bookmark, press the BOOKMARK button, select the bookmark
using the and and buttons and then press the PLAY button.

4. Press OK to start playing the two files at the same time. 5. Press the STOP button to stop playback. To rent (purchase) DivXVOD files
DivX VOD files are downloaded after paying a rental from certain commercial websites. Prior to downloading a VOD you need to input the registration number of your DVD player on the purchase form on the site. Follow the instructions below to find the registration number of your player: insert a disc and press the SET UP button and then the ZOOM button. Write down this VOD 8-character registration number so that you can fill in the form on the website you purchase your DivX VOD files from.
Note: If you cannot play a DivX VOD file recorded on a CD-R disc after downloading it, the rental period allocated during purchasing from the website may have expired. It is also possible that the recorded file is not compatible with your player because of different versions or incorrect download parameters.The parameters used when copying to CD-R may be another reason for this. Since it is not possible here to supply all the information, parameters and advice relating to the use of DivX VOD files, we recommend that you visit specialist websites such as www.divx.com/vod.

buttons and press

Frame advance (all discs except audio CD, mp3,WMA and DivX) 1. While the disc is playing, press PAUSE once. 2. Press the PAUSE button a number of times to advance forward image by image. 3. Press PLAY to resume normal playback. Variable slow motion (DVD and VCD only) 1. While the disc is playing, press PAUSE once. 2. Press the REV or FWD button a number of times to vary the speed and direction of the

slow motion.

5. To delete a bookmark, press the BOOKMARK button, select the bookmark using the
buttons and then press the CLEAR button. To exit the bookmark function, press the BOOKMARK button again.
Disc menu To change the language of the disc menus, choose the language using the and press OK to confirm.

buttons

Ratings You can control access to the player and the type of discs your family can watch with the rating function.There are eight levels of parental control.
Note:The disc publisher is responsible for coding scenes according to the rating limits. In Europe, very few discs have coded scenes.

Status menu

Press the DISPLAY button a number of times during playback to show in turn: DVD:Title elapsed time,Title remaining time, Chapter elapsed time, Chapter remaining time, Display Off. VCD and audio CD: Single elapsed time, Single remaining time,Total elapsed time,Total remaining time, Display Off. mp3 and DivX: Single elapsed time, Single remaining time.
1. Select the rating level using the and buttons. 2. Press OK to enter the Password Setup menu.
Note:To access the Ratings submenu, you must input a four-digit password. If you have not chosen one yet, you are prompted to do so when you try to access it (see option Password).
3. Press PLAY to resume normal playback.
Note: Reverse slow motion is not possible with a Video CD.
3. Enter your four-digit password and press OK. If you have not chosen one yet, the factory
preset password is 1369. Password This option allows you to set or change the password. 1. Press OK to enter the Change Password menu. 2. To change the password, enter the current four-digit password in the Old Password box. Then enter the new password in the New Password box.You are then prompted to enter it again in the Confirm Password box to confirm and press OK.

Changing chapter/track

While the disc is playing, press the SKIP or SKIP button to go immediately to the next or previous chapter, or to the next or previous track. For audio CD and VCD only: enter the track number with the number buttons and then press OK.

PBC (VCD)

The PlayBack Control function offers scenes and information which can be selected interactively via a menu. It can also be used to display high-resolution pictures, if the disc contains any. Press the DISC MENU button to access the PBC menu and the TITLE MENU button to turn the PBC function on and off.

Repeat playback

While the disc is playing, press the REPEAT button repeatedly to select a play mode: mp3 and WMA: Repeat One, Repeat Folder, Folder (=Off), JPEG and DivX: Repeat One, Repeat All, Repeat Off.
Zoom (DVD,VCD and DivX only) 1. While a disc is playing, press the ZOOM button until you reach the zoom size you

require.

Preview (DVD and VCD) 1. Press the PREVIEW button during playback to display the Digest menu. It includes
various options depending on the type of disc: DVD:Title Digest, Chapter Digest,Title Interval, Chapter Interval and Bookmark Digest; VCD:Track Digest, Disc Interval and Track Interval.
Programme playback (mp3 and WMA) 1. Insert a disc. 2. Use the , , and buttons to select the file you want to add to the playback list

and press the BOOKMARK button. Repeat this step as often as necessary. 3. Press the PROGRAM button to display the playback list and press PLAY to start playback. Files are played in the order of the playback list. Playback stops once all files have been played.To delete a file from the list, press the PROGRAM button, use the and buttons to select the file from the playback list and press BOOKMARK to delete it. 4. Press the OPEN/CLOSE button to delete the playback list.

Additional Information

Troubleshooting
The appliance does not switch on.
Make sure it is plugged into a mains socket. Press the button on the remote control or the ON/STANDBY button on the front of the appliance.
2. Move from one area to another using the Memory card readers

buttons.

Your DVD player comes with 3 built-in memory card readers. The bottom reader takes Compact Flash 1, Compact Flash 2, and Microdrive cards.The top reader takes SD, MMC, Memory Stick, Memory Stick Pro, and Smartmedia cards.You can read MP3,WMA, JPEG, or MPEG-4 files stored on these cards.
2. Select one of the digest types:
- Title Digest/Chapter Digest/Track digest: shows a digest of all titles/chapters/ tracks available on the disc. - Title/Chapter/Disc/Track Interval: shows a digest of the current title/chapter/disc/ track in 10 minutes interval. - Bookmark Digest: shows a digest of all bookmarks created on the disc.
It is impossible to read the disc.
Insert the disc with the printed side facing up. Check that the disc can actually be played by this device (see below). Check that the discs regional code matches the players regional code.This players regional code is 2. Clean the disc (see below).
1. Insert a memory card into the reader. 2. Press the SELECT button on the front of the DVD player to display the memory card's

contents.

Note: a memory card can be inserted at the same time in each of the readers, as well as a disc (CD or DVD) in your DVD player.To switch between playback sources (Card 1, Card 2,Card 3 or Disc), press the SELECT button.

Player menus

Using the players menus
Press the SET UP button to display the players main menu. Select a menu icon using the and buttons.Then select one of the available options using the and buttons. Press the button to access the submenu and use the and buttons to select an option.Then press OK to confirm your selection. Return to a previous menu using the button. To exit from the player menus, press the SET UP button again.

There is no picture.

Check you have switched on the TV set. Check the connections. Select the AV input assigned to the player on the TV.