324246RV600ETY_En.indd 3

The inside of this TV will overheat if the ventilation holes are covered, blocked or sealed, which may result in a re. 8) Install the TV in a horizontal, stable location. Connect between two clips on the back of the TV and a wall, pillar, etc., with a sturdy tie and clip of supplied accessories (- back cover). Use as short a tie as possible to ensure the TV is stable. If the TV is not installed securely, it may lean or fall over and cause an injury. To prevent injury, use the exclusive optional stand or wall-hanging bracket to install this TV on the oor or wall securely in accordance with a qualied technician.
Sturdy tie (as short as possible)
5) Never place the TV near a heater or in direct sunlight. The surface of the cabinet or power cord may melt and result in a re or an electric shock.

Clip Clip

6) Never place the TV in an area exposed to high humidity levels, such as in a bathroom or close to a humidier. This may cause a re or an electric shock.

Side view

Top view
9) Precautions for moving the TV When moving the TV, be sure to remove the plug from the wall outlet and disconnect the aerial cable and audio/video cables, any steady ties. A re or an electric shock may result if the power cord is damaged. When carrying the TV, at least two people are needed. Be sure to carry it upright. Never carry the TV with the screen facing up or down.
7) Never place the TV next to a stove where it will be exposed to oil, smoke, or steam, or in a location where there is a large quantity of dust. This may cause a re or an electric shock.
10) Precautions for installing on outdoor aerial An outside aerial system should not be located in the vicinity of overhead power lines, or other electric light or power circuits. If the aerial falls down or drops, it may cause an injury or an electric shock.

324246RV600ETY_En.indd 4

7/28/2009 10:08:04 AM
1) Never place hot objects or open ame sources, such as lighted candles or nightlights, on or close to the TV. High temperatures can melt plastic and lead to res.
4) Never stand or climb on the TV. Educate children about the dangers of climbing on furniture to reach the TV or its controls. Be especially careful in households with children to prevent them through climbing on top of the TV. It may move, fall over, break, become damaged or cause an injury.

2) The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on the apparatus. When liquids are spilled or small items are dropped inside the TV, this may cause a re or an electric shock. If small objects drop inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician.
5) When the TV will not be used for a long period of time, such as during vacation or travel, remove the power plug from the wall outlet for safety. The TV is not completely disconnected from the power supply line, as minute current is consumed even when the ! Power switch is turned off. The Mains plug or an appliance coupler is used as the disconnect device, therefore the disconnect device shall remain readily operable.
3) Never insert objects (metal or paper) or pour water inside the TV through ventilation holes and other openings. These items may cause a re or an electric shock. If these objects are inserted inside the TV, turn off the TV and remove the power plug from the outlet immediately and contact a service technician. Be especially careful that children do not insert objects in the TV.
6) Never pull on the power cord when removing the plug from the wall outlet. Always hold the plug rmly when removing it. If the power cord is yanked, the cord may become damaged and a re or an electric shock may occur.

324246RV600ETY_En.indd 5

7/28/2009 10:08:05 AM
7) Never cut, break, modify, twist, bunch up or bent the cord or apply excessive force or tension to it. Never place heavy objects on the cord or allow it to overheat as this may cause damage, a re or an electric shock. Contact a service technician if the power cord is damaged. 3) If the TV is dropped or the cabinet is broken, turn off the TV and remove the power plug from the outlet immediately. If the TV has power in this condition, it may cause a re or an electric shock. If the cabinet is broken, be careful when handling the TV to prevent an injury. Contact a service technician for inspection and repair.
8) If there is thunder or lightning, never touch the aerial cable or other connected cables. You may suffer an electric shock.

Press press

to select the new position 4, then.
Pos. Label EFGH IJK L MNOP ABCD

Setting the Location

You can select either Home or Store mode. Home is recommended for normal home use. Select Store when using a TV for displaying in a shop, etc.
From the SET UP menu, press select Location. Press or

to select Home or Store.

Press press Press press
to select the channel MNOP, then. to select the new position 1, then.
Conrm new Manual tuning menu.
Pos. Label MNOP EFGH IJK L ABCD
324246RV600ETY_En.indd 17

7/28/2009 10:08:12 AM

Picture adjustment
Most of the picture controls and functions are available. However features not available will be greyed out.

Cinema

When watching all sides panel format lms/ video tapes, this setting will eliminate or reduce the black bars on all the sides of the screen by zooming in and selecting the image without distortion.
Selecting the picture size
Press until the picture size list appears on the screen, then press or to select the appropriate picture size (or press repeatedly to select the desired picture size directly). AV format

Picture Size

Native Wide 4:3 Super live Cinema Subtitle 14:9

Subtitle

When subtitles are included on a letterbox format broadcast, this setting will raise the picture so that the most of text is displayed.

Press Q.

Use this setting when watching a 14:9 broadcast.
Use this setting when watching a wide-screen DVD, widescreen video tape or a 16:9 broadcast (when available). Due to the range of widescreen formats (16:9, 14:9, 20:9 etc.), you may see bars on the top and bottom of the screen.

Native

This setting will display the image correctly without distortion or picture clipping.
Use this setting to view a true 4:3 broadcast.

PC Normal

Use this setting for PC connected via HDMI or RGB/PC terminal when receiving PC signal format. This setting will display the image correctly without distortion or picture clipping.

Super live

This setting will enlarge a 4:3 image to t the screen by stretching the image horizontally and vertically, holding better proportions at the centre of the image. Some distortion may occur.

PC Wide

Use this setting for PC connected via HDMI or RGB/PC terminal when receiving PC signal format. This setting will display the image without picture clipping.
324246RV600ETY_En.indd 18
Press MENU, then press the SET UP menu.

Dot by Dot

Dot by Dot is a non-scaling display. Depending on the input signal format, the picture is displayed with side panels and/or bars at the top and bottom (i.e. VGA input source).
Language Auto tuning Manual tuning Manual setting AV connection PC Setting Picture position Quick Setup Location

English

Notes: In the PC connected via HDMI or RGB/PC terminal (- page 32), the picture size selection is PC Wide, PC Normal or Dot by Dot only. Using the special functions to change the size of the displayed image (e.g. changing the height/width ratio) for the purpose of public display or commercial gain may infringe on copyright laws. If the aspect ratio of the selected format is different from the one of the TV transmission or video programme, it can cause a difference in vision. Change to the correct aspect ratio picture size. When using the PC connected via HDMI or RGB/PC terminal, the moving image quality may be deteriorated.
to select Picture position. to select the
Press Q, then press or item you want to adjust.

Picture position

Horizontal position Vertical position Reset

Press or desired.

to adjust the settings as

Horizontal position

Using the picture still
Press r to freeze the picture. Even if an image is frozen on the TV screen, the pictures are running on the input source. Audio continues to be output as well. To return to a moving picture, press r again.
Notes: When the picture size is in Wide or 4:3 mode, only the Horizontal position can be adjusted. When the picture size is in Native, PC Wide, PC Normal and Dot by Dot mode, none of this function will be available.
Resetting the picture position
This function resets your picture position settings to the factory settings.
From the Picture position menu, press to select Reset. Press Q.

(Moving)

( St ill)
Activating the Picture Mode
Note: If you use this function except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws. This TV offers the choice of personalising the picture style. AutoView, Dynamic, Standard, Mild, Movie, Game and PC (PC Fine) are preset options and affect many features/settings within the TV.
Adjusting the picture position
Adjustment to the position of the picture may be made to suit your viewing preferences.

From the PICTURE menu, press select Active Backlight Control. Press or to select On or Off.
Note: This function is available for 480i and 576i signals.
Activating Auto Brightness Sensor
When auto contrast is activated it will automatically optimize the backlighting levels to suit ambient light conditions.
Adjusting the colour management
You can adjust the picture colour quality by selecting from 6 base colour adjustments : Red, Green, Blue, Yellow, Magenta or Cyan.
From the PICTURE menu, press select Auto Brightness Sensor. Press or to select On or Off.
From the PICTURE menu, press select 3D Colour management.
324246RV600ETY_En.indd 21

7/28/2009 10:08:14 AM

Sound adjustment
Setting the MTS (Multi-channel TV Sound)

Auto mode

The MTS Auto mode automatically recognize stereo/bilingual programmes depending on the broadcast signal.
Selecting the stereo programmes
When a stereo programme is received, d Stereo appears.

Stereo

Press MENU, and then press display the SOUND menu.
Press g to select the stereo/monaural mode. d Stereo and e Mono appear cyclically on the screen.
Selecting the bilingual programmes
When a bilingual programme is received, j Dual appears. Press g to select the sound to be heard. The sound differs according to the transmission system: NICAM or German stereo/bilingual broadcast.
Press or to select MTS, and then press or to select Auto or Mono.

Mono mode

If you experience noise or poor reception of any stereo/bilingual programme, set the MTS mode to Mono. Noise will be reduced and reception may improve. Note: If you experience noise with a particular programme on whose channel reception is usually good, try setting MTS mode to Auto, then switch g to e Mono (monaural).

Dual 1

Sound to be heard Display NICAM Sub I sound Sub II sound Main sound German stereo/ bilingual broadcast Main sound Sub sound

j Dual 1 J Dual 2 e Mono

Selecting the dual 1 or dual 2 mode
You can hear only dual 1 or dual 2 sound selected, whenever bilingual programmes are received.
Note: These settings are not stored in the TV memory.
Adjusting the sound quality

Press MENU, then press the FUNCTION menu.

Other features settings

Selecting the timer menu
The Timer is especially useful if you want the TV to turn itself on or off after a selected period of time.
Media Player Teletext Teletext language Auto format 4:3 stretch Blue screen Side panel

Auto 1 On Off On 1

Press MENU, and then press display the TIMER menu.
to select Auto format, then to select On or Off.
324246RV600ETY_En.indd 23

7/28/2009 10:08:15 AM

Activating blue screen
With the blue screen function On, the screen will automatically turn blue and the sound will be muted when no signal is being received.
From the FUNCTION menu, press select Blue screen.
Press or to select On or Off. Note: In the PC input mode, PIP mode (- page 25) or teletext mode (- page 27), this function is not available.
Activating the 4:3 stretch
When 4:3 stretch is activated, this function will switch 4:3 format programmes into a full screen picture.
From the FUNCTION menu, press select 4:3 stretch.
Press or to select On or Off. Note: In HDMI signal format, this function is available.
Press Q. o 1 (o (1), video 1 input), o 2 (o (2), video 2 input) or o 2S (S-video input), o 3 (o (3), component video input), o 4 (o (4), component video input), HDMI1, HDMI2, HDMI3, HDMI4 (HDMI input), PC (o RGB/PC, PC input) Notes: When the component video input, PC input mode or HDMI input mode is selected, the MONITOR OUT output terminals (- page 30) output audio signal only. If a REGZA-LINK device is connected to an HDMI input, the REGZA-LINK icon will appear. When the TV is switched on, it will take a few minutes for the REGZA-LINK icon to appear in the list; when an HDMI cable is removed, it will take a few minutes for the icon to disappear. If the HDMI cable from connected device is changed or HDMI device setting are changed, Enable REGZA-LINK in the REGZA-LINK menu may need to be reset to On.
Adjusting the brightness of side panel
You can adjust the brightness of side panel in 14:9 or 4:3, etc. mode.
Setting the manual setting menu
From the FUNCTION menu, press select Side panel. Press or required.

Side panel

Selecting the video input source to view
Press L on the remote control until the video input mode list appears on the screen, then press , or L to select appropriate input source (or press o on the TV right side panel to select required input source directly).

Inputs

TV HDMI1 HDMI2 HDMI3 HDMI4 PC
Press or press Q. Press press below. or or
to select Manual setting, then to select an item, and then to select the item as shown
Manual setting Colour system : Auto EXT1 A
A. Colour system Conrm that colour system is set to A (Auto). If not, select A with or.

324246RV600ETY_En.indd 24
B. Label The label allows you to label each input source for your TV. To change or create labels: 1) Press or repeatedly to select a character for the rst space, then press or.

Displaying a sub-picture

Select the TV programme or HDMI signal you want to watch. Press to open the Quick Menu, press or to select PIP. Press Q to display a sub picture will appear on the screen. Main picture source Sub-picture source

(Main picture)

(Sub- picture)
2) Repeat step 1) to enter the rest of the characters. If you would like a blank space in the label name, you must choose a blank space from the list of characters. 3) Press Q to store your settings.

Channel List

Press the LIST button. The Channel List will appear.
Notes: When the input signal is in 1080i and the picture size select the Native mode (- page 18), the picture size will be changed Wide mode when using this function. The sub-picture has no sound. The sub-picture cannot change channel position.
Changing the position of the sub-picture
While watching the image in PIP, press or repeatedly.
Press or to select a channel or input, and press Q to watch.
Switching the position of the main and the sub-picture
Watching PIP (Picture-in-Picture)
This TV is capable of displaying two pictures simultaneously. This is called the PIP (Picture-in-Picture) function. A TV picture or a picture from external source equipment can be displayed as a subpicture. When the main picture is a TV or Standard (Composite) video pictures, the sub-picture can only be HDMI, Component video or PC pictures. When the main picture is a picture from HDMI, Component video or PC pictures, the subpicture can only be from a TV or Standard video pictures.
While watching the image in PIP, press , then press or to select PIP SWAP. The main and sub-picture are switched. Select the mode again to switch again.

Closing the PIP Mode

While watching the image in PIP mode, press. Press or press Q. to select PIP Off, and then
324246RV600ETY_En.indd 25

7/28/2009 10:08:16 AM

Using REGZA-LINK
This feature uses CEC (Consumer Electronics Controls) technology and allows the control of Toshiba REGZA-LINK compatible devices from the TV remote control via HDMI connection (- page 34). Note: Not all Toshiba products currently support REGZA-LINK.

REGZA-LINK one touch play
When a connected device is turn on REGZALINK will automatically detect the TV through the input selection. If the TV is in standby it will be turn on automatically. This feature is selected in the REGZA-LINK setup menu. Note: Even if the device is showing a menu the TV may automatically show the video input source on-screen display.
Notes: When you turn on the AV amplier, change its input source, or adjust the sound volume, the sound will be output from the AV ampliers speakers even if TV Speakers has been selected for Speaker Preference in the REGZA-LINK menu. Turn the TV rst to standby and on again to output the sound from the TVs speaker. The proper function may not work by operating AV amplier. In this mode, the PIP function (- page 25) is not available. The above functions are dependent on the connected device and TV setting.

REGZA-LINK functions

When the Enable REGZA-LINK is set to On, it allows the following functions to be enabled by setting them to On. TV Auto Power If a REGZA-LINK device is turned on or off, the TV turns on or standby automatically. Auto Standby If the TV is set to standby, the TV will send a message to turn off the selected REGZA-LINK device connected to the TV. Speaker preference From this item, you can set your audio output preference to the TV speakers or the AV amplier speakers. When this item is set to Amplier, the TV remote control can be used to adjust or mute the volume of the audio. This item will be greyed out unless a REGZA-LINK compatible AV amplier is connected. This feature can be operated from the Speaker in the Quick Menu. Notes: When you turn on the AV amplier, change its input source, or adjust the sound volume, the sound will be output from the AV ampliers speakers even if TV Speakers has been selected for Speaker Preference in the REGZA-LINK menu. Turn the TV to standby and on again to output the sound from the TVs speakers. The above functions are dependent on the connected device and TV setting.
REGZA-LINK system standby
This feature automatically turns the connected device into standby when the TV goes into standby and conversely for the TV to switch into standby when connected device goes into standby.
REGZA-LINK system audio control
Using the Speaker preference feature allows the TV remote control to adjust the volume or mute the sound of the speakers connected to the TV via an AV amplier. Ensure that the connected AV amplier and REGZA-LINK device are selected in the input source selection and that the Speaker is set to Amplier in the Quick Menu.

324246RV600ETY_En.indd 26
To set the REGZA-LINK set up
Press MENU and or REGZA-LINK menu.

to select the

If the HDMI cable from connected device is changed or HDMI cable from connected device setting are changed, Enable REGZA-LINK in the REGZA-LINK menu may need to be reset On.
To control the REGZA-LINK device
First select the HDMI input source with the desired REGZA-LINK device connected, then switch the mode on the remote control to REGZA-LINK and press the available button on the remote control (- page 12). On the sub-picture mode (- page 25), this function is not available.
Press or to select Enable REGZALINK, then press or to select On. Note: If you set Enable REGZA-LINK to Off, the all other items will be greyed out. Press or to select the REGZA-LINK set up item you want to use, and press or to select On/Off or the desired speakers mode. TV Auto Power: On/Off Auto Standby: On/Off Amplier Control: On/Off Speaker Preference: TV Speakers/ Amplier (See details on the previous page.)
The TV features that can be controlled by the connected device remote control are:
Power standby, Volume, Programme channel, Sound mute, Input selection, Number buttons, Previous programme channel etc. Note: These functions are dependent on the connected device. Not all the remote control buttons may be available. Please refer to the owners manual for all the connected devices.

REGZA-LINK PC link

This feature automatically adjusts the suitable widescreen formats and picture preferences, when connected to a REGZA-LINK PC. Notes: This feature depends on the connected equipment state. To select the PC Fine in the Picture Mode (- page 19).
REGZA-LINK input source selection
When any devices using CEC technology has connected, REGZA-LINK icon shows on the input source list.

Teletext

This TV has a multi-page teletext memory, which takes a few moments to load and it offers two ways of viewing Teletext Auto and List which are explained below.
Setting up the teletext mode
To select a language for teletext:
The language 1-4 option enables the display of different language when using Teletext.
To select the REGZA-LINK input source, refer to Selecting the video input source to view on page 24. Notes: This function depend on the devices connected. When the TV is switched on, it will take a few minutes for the REGZA-LINK icon to appear in the list; when an HDMI cable is removed, it will take a few minutes for the icon to disappear.

Press or Analogue.

to select Auto, Digital or
324246RV600ETY_En.indd 32

7/28/2009 10:08:19 AM

Connecting your TV To connect a PC to the HDMI terminal on the TV:
When connecting a PC to the HDMI terminal on the TV, use an HDMI-to DVI adapter cable and analogue audio cables. If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). Separate analogue audio cables are not necessary. TV back view

Using the PC setting

Most of the picture controls and functions are available. However features not available will be greyed out. In the PC input mode, the Manual setting (- page 24) is not displayed. First press L until the video input mode list appears on the screen, then press or and Q in order to select the PC input mode (- page 24). This function may not be available for some signal or if no signal is received. The optimum points of the clock phase and sampling clock adjustments may be incomprehensible according to the input signals.
For acceptable PC signal format, see page 31. Notes: The edges of the images may be hidden. If connecting a certain PC model that signal is particular, the PC signal may not be detected correctly.

to select PC Setting.

Signal names for mini D-sub 15 pin connector
Pin assignment for RGB/PC terminal

Pin No. 7 8

Signal name R G B NC (not connected) NC Ground Ground Ground

Pin No. 15

Signal name NC Ground NC NC H-sync V-sync NC
Press Q to display the PC Setting menu.

PC Setting

Horizontal position Vertical position Clock phase Sampling clock Reset
Press or to select an option you want to adjust. Press or to adjust the settings as required.
324246RV600ETY_En.indd 33
Adjusting the clock phase of the picture
If the clock phase, which synchronize the PC signal and LCD display, is not optimized, the picture will blur. This function enables you to adjust clock phase and display a clear picture.

REGZA-LINK connection

You can control the basic functions of connected audio/video devices using the TVs remote control if you connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and operations, see pages 26, 27.
From the PC Setting menu, press select Clock phase. Press or
to obtain a clear picture.
Before controlling the device(s):
After completing the above connections, set the REGZA-LINK setup menu as you desire (- page 27). The connected devices must also be set. For details, see the owners manual for each device.

Clock phase

Adjusting the sampling clock
If the sampling clock does not match with the dot clock frequency of the PC, blurred picture detail will occur, or screen width will change, or drift patterns in vertical lines may be apparent. This function enables you to adjust it and optimize the picture.

Insert a USB device into the USB terminal on the right side of the TV. Press or and highlight Media Player, and then press Q. Press or to select Photo, and press Q. The list of les will appear. Press or to select the USB device if the selection window is displayed.

during Slide Show mode.

Press or to highlight the item (Interval Time or Repeat). Press Press or or to adjust the setting. to return to Slide Show mode.

Viewing JPEG les

To view in Single View mode:
When the list window appears after starting the Media Player, press or to select a le or folder.

Photo / /

Description To set a time interval to view Interval Time photos (3sec, 5sec, 10sec, 15sec, 30sec, 60sec, or 90sec). To display photos in the same Repeat directory repeatedly. On/Off

To rotate the image:

While viewing the image in Single View mode, press to rotate the image 90 degrees clockwise, press to rotate the image 90 degrees counterclockwise.
.JPG.JPG.JPG.JPG.JPG.JPG.JPG 5/8 2008/08/01 19:40 2560x1920.JPG
To return to the list window:
Press during Single View mode or Slide Show mode.
To display le status information:
Press Q to begin viewing the selected le or to move to the next layer. : To return to the previous layer.
Press to view the next le, or press to view the previous le. Note: If the previous or next le is not compatible, it will be skipped automatically.
Press. The following information will be displayed at the bottom of the screen. File number/Total number of les (only for les stored in the same directory) Photo title Date and time taken File size Slide Show icon (if applicable) Repeat play icon (if applicable) Operation guide
To view in Slide Show mode:
To switch to Slide Show mode, press Q during Single View mode. Note: To return to Single View mode, press Q again. Press to view the next le, or press to view the previous le. Note: If the previous or next le is not compatible, it will be skipped automatically. Press Q to return to Single View mode.
Press again to remove the information from the screen. Note: The le status information will disappear after about 6 seconds.

File Compatibility:

Data compatibility: JPEG Exif ver 2.2 File format: DCF ver 1.1 Maximum viewable resolution: pixels (Total number of pixels: 16,000,000) Total number of les: Less than 2000 per folder

No REGZA-LINK operation

The REGZA-LINK feature is available for Toshiba REGZA-LINK compatible devices. Make sure the HDMI cables with HDMI logo are used. When the connected REGZA-LINK device does not work correctly after you have changed setting of the device, turn off your TV and unplug the power cord, then plug and turn on again. If several devices are connected, REGZALINK feature may not operate properly. Read the owners manual furnished with the connected REGZA-LINK device.

Teletext problems

Check the aerial connections. Good performance of text depends on a good strong broadcast signal.
The brightness of the screen comes down, or ickers of the screen are caused, or some parts of the screen do not light up.
When you just buy and start to use this TV, a ickering may be caused in the screen. In this case, switch off the TV, then switch on it again to cure the condition. The cold cathode uorescent lamp used for the back light on this TV has longevity. When the brightness of the screen comes down, or the ickers of the screen are caused, or some parts of the screen do not light up, it may reach the end of its life. Contact a service technician.
324246RV600ETY_En.indd 37

7/28/2009 10:08:21 AM

Broadcast system
Broadcast transmission systems of each country or region
Asia M.E. Country or region Bahrain, Kuwait, Israel, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, etc. China, Vietnam China Hong Kong Iraq, Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. Russian Federation, etc. Myanmar, etc. Oceania Country or region Australia, New Zealand, etc. Africa Country or region Republic of South Africa, etc. South America Country or region Brazil Chile, Colombia, etc. Colour PAL NTSC Sound M M Colour PAL Sound I Colour PAL Sound B/G Colour PAL PAL PAL SECAM SECAM NTSC Sound B/G D/K I B/G D/K M
Note: PAL, SECAM and NTSC 3.58 (MHz) are different colour signal broadcast transmission systems applicable to different countries or region. NTSC 4.43 (MHz) is used in special VCRs to playback NTSC recorded video tapes through PAL television equipment.
324246RV600ETY_En.indd 38

Specications

LCD colour television
Model 32RV600E, 32RV600T, 32RV600Y 42RV600E, 42RV600T, 42RV600Y 46RV600E, 46RV600T, 46RV600Y Power source 32RV600E, 42RV600E, 46RV600E: 220V-240V AC, 50/60Hz 32RV600T, 42RV600T, 46RV600T: 110V-240V AC, 50/60Hz 32RV600Y, 42RV600Y, 46RV600Y: 220V-240V AC, 50Hz Power consumption 32RV600E/T/Y: 88 W, 0.6 W (standby) 42RV600E/T/Y: 144 W, 0.6 W (standby) 46RV600E/T/Y: 231 W, 0.8 W (standby) Dimensions 32RV600E/T/Y: 786 mm (W) 567 mm (H) 247 mm (D) 42RV600E/T/Y: 1,009 mm (W) 689 mm (H) 264 mm (D) 46RV600E/T/Y: 1,108 mm (W) 740 mm (H) 299 mm (D) Mass (Weight) 32RV600E/T/Y: 13.5 kg 42RV600E/T/Y: 21.5 kg 46RV600E/T/Y: 23.0 kg Television system (Aerial input) Channel coverage:

PAL B/G (CCIR) VHF UHF CATV VHF UHF CATV VHF UHF CATV VHF UHF CATV VHF UHF CATV VHF UHF CATV NTSC M (JAPAN) VHF UHF CATV 2 - - 69 X - Z+2, S1 - S- - - 57 Z1 - Z- - 69 X - Z+2, S1 - S- - 69 X1 - X- - 69 A6 - A1, A - W, AA - ZZ, AAA, BBB 1 - - 62 M1 - M10, S1 - S41
PAL 60 Hz colour system 5.5/6.0/6.5 MHz sound system COMPONENT VIDEO INPUT terminals (the signal format) 480i, 480p, 576i, 576p, 720p (50/60 Hz), 1080i (50/60 Hz) (These signal formats are converted to match the number of pixels of the LCD panel.) Colour system PAL, SECAM, NTSC 3.58/4.43 Aspect ratio 16 : 9 Visible size (diagonal) 32RV600E/T/Y: 80.1 cm 42RV600E/T/Y: 106.7 cm 46RV600E/T/Y: 116.8 cm Number of pixels 1920 (H) dots x 1080 (V) dots Audio power 10 W + 10 W Speakers Main 160 mm 2pcs. Input/Output terminals
o (1) o (2) Input Phono jacks Input 4 pin Phono jacks Input Component video Phono jacks o (4) Input Component video Phono jacks O MONITOR A/V S-video A/V Y, PB/CB, PR/CR Audio L/Mono +R Y, PB/CB, PR/CR Audio L/Mono +R

D/K (CHINA)

B/G (CCIR)

D/K (OIRT)

Special RF signal: NTSC 4.43 colour system 5.5/6.0/6.5 MHz sound system
Output Phono jacks A/V Input o RGB/PC Mini D-sub 15 pin Analogue RGB Input o PC/HDMI1 (AUDIO) 3.5 mm (Diameter) stereo Input (type A) o HDMIpin A/V Digital Input (type A) o HDMIpin A/V Digital Input (type A) o HDMIpin A/V Digital Input (type A) o HDMIpin A/V Digital V.1.3a with Lip Sync Headphone jack 3.5 mm (Diameter) stereo
324246RV600ETY_En.indd 39
Operating condition Temperature 0C - 35C Humidity 20% - 80% (No moisture condensation) Supplied accessories Owners manual (1), Remote control (1), Batteries (2), Clip (1), Cleaning cloth (1)
This is used to x the TV to a wall, pillar, etc. (- page 4). Design and specications are subject to change without notice. Never service or remodel the TV by yourself. It may expose you to a re hazard or dangerous voltages.
324246RV600ETY_En.indd 40

7/28/2009 10:08:22 AM

42RV600 SERIES SPECIFICATION
MODEL MAIN Product Type Screen Type Aspect Ratio Dynamic Contrast Ratio *
2 Brightness (cd/m ) Resolution (H x V) Viewing Angle (Degrees) Power Meta Brain Video Processing Panel Response Speed (ms) SIGNALS Receiving System Colour System Video Signal RGB Signal** VGA: 640 x 480 (60/ 72/ 75Hz) SVGA: 800 x 600 (60/ 72/ 75Hz) XGA: 1024 x 768 (60/ 70/ 75Hz) W-XGA: 1280 x 768 (60Hz (@68.25MHz,79.5MHz)/ 75Hz) W-XGA: 1360 x 768 (60Hz) S-XGA: 1280 x 1024 (60/ 75Hz) VISUAL 3D Colour Management Autoview Exact Scan Mode Intelligent Backlight Control AUDIO Stereo System Speakers Audio Output Audyssey EQ *** CONNECTION Antenna Input EXT 1 EXT 2 EXT 3 EXT 4 EXT 5 EXT 6 EXT 7 EXT 8 PC Input Monitor Output Digital Input Headphone FEATURES REGZA Link Picture in Picture Teletext Multilingual OSD Hotel Mode**** Swivel Stand GENERAL
42RV600E/Y/T FULL HD LCD TV 42 16:9 50000:1920 x O 10 BIT 6.5 PAL I/ BG/ DK, SECAM BG/ DK, NTSC M/ BG 4.43 PAL, SECAM, NTSC 3.58 / 4.43 480i/480p (60Hz), 576i/576p (50Hz), 720p (50/60Hz), 1080i (50/60Hz), 1080p (24/25/30/50/60Hz) through HDMI O O O O O O O O ***** O O NICAM B/G, I, D/K, & German Stereo B/G, D/K Main L&R (3.5 x 16cm) x 2 10W x 2 O 1 Input: Composite Video + RCA Audio Input: S-Video + Composite Video + RCA Audio Input: Component Video + RCA Audio Input: Component Video + RCA Audio Input: HDMI 1 + 3.5mm Mini Jack Audio (Common with PC Audio) Input: HDMI 2 Input: HDMI 3 Input: HDMI 4 (side) D-Sub 15 Pin + 3.5mm Mini Jack (Common with HDMI 1 Audio) Composite Video + RCA Audio USB (JPEG Playback) 3.5mm Mini Jack O (HDMI CEC) HDMI / D-Sub PC + RF O English / French / Persian / Russian / Simplified Chinese / Malay / Vietnamese / Thai / Arabic O Fixed Stand E: 220-240V 50/60Hz Y: 220-240V 50Hz T: 110-240V 50/60Hz x 649 x x 689 x 264 20.0 21.5 WAL12S / WAL13C
Automatic Voltage Regulator Power Consumption (W) Dimension (W x H x D) mm without Stand Dimension (W x H x D) mm with Stand Weight (Net) kg without Stand Weight (Net) kg with Stand OPTIONAL ACCESSORIES Wall Mount Bracket
* dynamic contrast ratio measured according to Toshiba standards ** These signal formats are converted to match the number of pixels of the panel. Small text may not be displayed properly.
*** Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey EQ is a registered trademark of Audyssey Laboratories. **** Hotel Mode is designed for use in hotels only. ***** The Histogram chart on the screen cannot be displayed Design and specifications are subject to change without prior notice