EU Declaration of Conformity
TOSHIBA declares, that the product: Satellite P10 conforms to the following Standards: Supplementary Information: The product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC. This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBAs web site http://epps.toshiba-teg.com on the Internet.
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la class B respecte toutes les exgences du Rglement sur le matriel brouilleur du Canada.
DVD-ROM, CD-RW/DVD-ROM (Combo), DVD-R/-RW, DVD Multi, DVDR/RW, DVD Super Multi drive safety instructions
CAUTION: The DVD-ROM, CD-RW/DVD-ROM (Combo), DVD-R/-RW, DVD Multi, DVDR/RW, DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. To prevent direct exposure to the laser beam, do not try to open the enclosure.
Location of the required label
Sample shown below. Location of the label on the drive and manufacturing information may vary.
CAUTION: This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest AUTHORIZED service station. To prevent direct exposure to the laser beam, do not try to open the enclosure. VORSICHT: Dieses Gert enthlt ein Laser- System und ist als LASERSCHUTZKLASSE 1 PRODUKT klassifiziert. Fr den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfltig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nchste autorisierte Service-Vertretung. Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gert nicht geffnet werden. ADVARSEL: Denne mrking er anbragt udvendigt p apparatet og indikerer, at apparatet arbejder med laserstrler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke p apparatets yderside kan bilve udsat for utilladellg kraftig strling. APPARATET BOR KUN BNES AF FAGFOLK MED SRLIGT KENDSKAB TIL APPARATER MED LASERSTRLER! Indvendigt i apparatet er anbragt den her gengivne advarselsmkning, som advarer imod at foretage sdanne indgreb i apparatet, at man kan komme til at udstte sig for laserstrling. OBS! Apparaten innehller laserkomponent som avger laserstrining verstigande grnsen fr laserklass 1.

ABC Names of windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. CAUTION: Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.
NOTE: Please read. A note is a hint or advice that helps you make best use of your equipment.

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Stress injury

Carefully read the Safety Instruction Manual. It contains information on prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. Chapter 3, Getting Started, also includes information on work space design, posture and lighting that can help reduce physical stress.

Heat injury

Avoid prolonged physical contact with the bottom of the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example) your skin might suffer low-heat injury. If the computer has been used for a long time, avoid direct contact with the metal plate supporting the I/O ports. It can become hot. The surface of the AC adaptor can become hot when in use. This condition does not indicate a malfunction. If you need to transport the AC adaptor, disconnect it and let it cool before moving it. Do not lay the AC adaptor on a material that is sensitive to heat. The material could be damaged.
Pressure or impact damage
Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can damage computer components or otherwise cause malfunctions.

PC Card overheating

Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time.

Carefully unpack your computer. Save the box and packing materials for future use. Check to make sure you have all the following items:

Hardware

Satellite P10 Series Portable Personal Computer Universal AC adaptor and power cord Other equipment or cables may be bundled depending on the model you purchased.

Software

The following software preinstalled on your hard disk: Microsoft Windows XP or (depending on the model you purchased) Microsoft Windows Media Center Edition 2004 (depending on the model you purchased) TOSHIBA Utilities Display Driver TouchPad driver Sound driver Miscellaneous drivers (depending on the model you purchased: Modem, LAN, SD, Wireless LAN, and/or FIR) Online help

Features

Product Recovery CD-ROM or DVD-ROM Tools and Utilities CD-ROM Additional Software (depending on the model you purchased): DVD Tools MicrosoftOneNote Microsoft Works 7.0 Microsoft Works Suite 2004 CAUTION: The system may not function properly if you use drivers that are not preinstalled or distributed by TOSHIBA

Documentation

Your computers documentation: Satellite P10 Series Personal Computer Users Manual Satellite P10 Series Quickstart Microsoft Windows XP Getting started booklet Safety Instruction Manual Warranty Information If any of the items are missing or damaged, contact your dealer immediately. NOTE: The instructions and pictures in this users guide concerning the
operating system are based on Windows XP. Users of other Windows operating systems should remember that the names of some menu items and procedures may differ from those described in this guide. Please refer to your operating system documentation if you have any problems.
The Satellite P10 series computer uses TOSHIBAs advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits:

Processor

Intel Celeron Processor up to 2.8 GHz or higher Mobile Intel Pentium 4 Processor up to 3.06 GHz or higher Mobile Intel Pentium 4 Processor up to 3.2 GHz or higher (supporting Hyper-Threading Technology)

Chip Set

ATI Mobility RADEON 9000IGP (depending on model) ATI Mobility RADEON 9700 (depending on model) Northwood RC300M for external graphics ATI IXP150 PC87591L for Keyboard Controller ENE CB712 for Card Bus PCMCIA SDIO controller ALC250 for AC97 CODEC TI TSB43AB21A for 1394a controller Realtek RTL8101L on board LAN ICS 951402AGT for system clock SMSC LPT47N217 for Parallel Port and Infrared Port controller Slots On board with two 200-pin +2.5V DDR SO-DIMM connector, supporting, DDR memory modules. Maximum upgradable to 2GB with two 1GB SODIMM modules. Video RAM Up to 128MB integrated solution with main memory for ATI Mobility RADEON 9000IGP Adiustable 64/128MB VGA DDR RAM for ATI Mobility RADEON 9700

Memory

1024KB Flash ROM for system BIOS Suspend to RAM/Disk Password protection Windows-ready with PnP Hot keys for system control Refreshable Complete ACPI 1.0b Function
Battery Pack 12-cell Li-Ion 18650 size smart battery pack with 95Wh capacity or 8-cell Li-Ion 18650 size smart battery pack with 63 Wh capacity Approximately 4 hour charge time to 100% when the system is off. Discharge time with main battery in standby mode is approximately 3 days for 12-cell battery and 2 days for 8-cell battery. Discharge time with main battery in shutdown mode is approximately 1 month. 12 hours or longer charging time to 100% (system on). RTC Battery The computer has an internal battery to back up the internal Real Time Clock (RTC) and calender. It is good with no external power source for 1 month on average. AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
Fixed hard disk Either one 30GB/40GB/60GB/80GB hard drive Bus Master IDE 9.5mm/ 2.5 HDD Support Ultra DMA 100 DVD-ROM drive Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12 cm (4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. The drive supports the following formats: DVD-ROM DVD-Video CD-DA CD-Text Photo CD (single/multi-session) CD-ROM Mode 1, Mode 2 CD-ROM XA Mode 2 (Form1, Form2) Enhanced CD (CD-EXTRA) CD-G (Audio CD only) Addressing Method 2
CD-RW/DVD-ROM Some models are equipped with a full-size, CD-RW/ drive DVD-ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed. For reading, this drive supports the same formats as the DVD-ROM drive. DVD-ROM DVD-Video CD-DA CD-Text Photo CD (single/multi-session) CD-ROM Mode 1, Mode 2 CD-ROM XA Mode 2 (Form1, Form2) Enhanced CD (CD-EXTRA) CD-G (Audio CD only) Addressing Method 2 DVD-R/-RW drive Some models are equipped with a full- size DVD-R/RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CDs/12 cm (4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 10 speed, DVD-R at maximum 2 speed, DVD-RW at single speed. This drive supports the same formats as the DVD-ROM drive. DVD-ROM DVD-Video CD-DA CD-Text Photo CD (single/multi-session) CD-ROM Mode 1, Mode 2 CD-ROM XA Mode 2 (Form1, Form2) Enhanced CD (CD-EXTRA) CD-G (Audio CD only) Addressing Method 2

PC Card One type II card socket only SRAM, OTPROM, FLASH ROM Mask ROM memory card MODEM/LAN card Card bus card PC Card 8.0 Compliant, supports 3V and 5V cards SD Card SD-BT card (PN:PA3271U-1BTM) supported SD memory capacity support from 8MB to 512MB
Ports (depending on model you purchased)
External monitor 15-pin analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus The computer has three Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enables data transfer speeds more than 40 times faster than USB 1.1 (which this computer also supports.) The USB drives may be used to transfer data at Low, Full, and High speeds. i.LINK (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras. Infrared The serial infrared port is compatible with the Infrared Data Association (IrDA 1.1) standards. Parallel port One 25-pin parallel port, EPP/ECP capability. S-Video port One TV-out connector.

Multimedia

Sound system Incorporates a Wave Table Synthesizer for advanced sound applications including 3D games, DVD movie playback and Internet communications. TV-out button Sets your display device to TV (video-out). Press it to switch back and forth between it and the LCD. Mode control button This button launches various CD, DVD and Digital audio functions. Refer to Chapter 4, Operating Basics, for more details. Internet Button Configurable button for opening an email program or a web browser on the fly. Direct CD Play Lets you use the computers fixed optical media drive as a stand-alone audio CD-player. You can also use the buttons to control the computers DVD video player or MP3 files when the system is on. Headphone jack A standard 3.5mm headphone jack. Microphone jack A 3.5 mm mini microphone jack enables connection of monoaural microphone input. Line-in jack A standard 3.5 mm line-in jack enables connection of a stereo device for audio input.

Communications

Modem An internal modem provides capability for data and fax communication. It supports V.90 or V.92 depending on the region. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 Mbps 100BASE-TX). Wireless LAN Some computers in this series are equipped with a wireless LAN mini-PCI card that is compatible with other LAN systems that support the following: 802.11a+g wireless LAN module/802.11g wireless LAN module. It has a Frequency Channel Selection (2.4 or 5 GHz) and allows roaming over multiple channels.

System Status Indicators

Figures 2-7 and the following show the system indicator lights, which light when various computer operations are in progress.

Hard Drive

Optical Disc Drive

SD Card

Wireless Communication
Figure 2-7 The Hard Drive LED indicates that the HDD is being accessed. Every time your computer runs a program, opens a file, or performs some other function in which it must access the HDD, this light goes on. The Optical Disc Drive LED indicates that an optical disc device is being accessed. The SD Card LED indicates the computer is accessing data from an SD Card. The Wireless Communication LED indicates the wireless LAN is active and that you may connect to a Local Area Network.

Battery

The DC-IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source. The Power LED flashes amber while the system is in Standby mode. The LED turns off when the computer is turned off or in hibernation mode. In normal operating mode, the LED is blue. The Battery LED indicates the battery's current charge/discharge status. It lights green when the battery is fully charged. It lights amber while the battery is being charged from the AC adapter. It flashes amber when the battery capacity is low.

Arrow Mode

Numeric Mode

Caps Lock

Figure 2-8 The keyboard indicators Arrow Mode When the Arrow mode icon lights green, you can use the keypad overlay (light gray labelled keys) as cursor keys. Refer to the Keypad Overlay section in Chapter 5, The Keyboard. Numeric Mode You can use the keypad overlay (light gray labelled keys) for numeric input when the Numeric mode icon lights green. Refer to the Keypad Overlay section in Chapter 5, The Keyboard. Caps Lock The Caps Lock LED lights when you press the Caps Lock key. When this light is on, pressing a letter key on the keyboard produces an uppercase (capital) letter.

Optical Media drive

One of the following optical media drives is installed in the computer: CD-RW/ DVD-ROM drive, DVD Multi drive, DVD-ROM drive, DVD-R/-RW drive, DVDR/RW drive, DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.

Restoring the preinstalled software from the Product Recovery disc
If pre-installed files are damaged, use the Product Recovery CD-ROM or DVDROM to restore them. To restore the operating system and all pre-installed software, follow the steps below. CAUTION: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. Make sure you have a backup copy of your data, before you perform a complete system recovery. 1. Load the Product Recovery CD-ROM or DVD-ROM in the drive and turn on the computer power. 2. When In Touch with Tomorrow TOSHIBA appears, press the F12 key. The Boot Menu appears. 3. Use your cursor keys to select the CD-ROM/DVD drive in the display menu. 4. Follow the on-screen directions. 5. If your computer came with additional software installed, this software can not be recovered from the Product Recovery disk. Re-install these
applications (e.g. Works Suite, DVD Player, Games, etc) separately from other media.
Restoring TOSHIBA utilities and drivers
If Windows is working properly, individual drivers or applications can be separately restored. Use the Tools & Utilities CD-ROM according to the instructions in the booklet contained in the CD box to reinstall TOSHIBA utilities and drivers.
TOSHIBAs Online Resources
TOSHIBA maintains a number of online sites to which you can connect. These sites can provide information about TOSHIBA products, give help with technical questions, and keep you up to date with future upgrades.

Chapter 4

Operating Basics
This chapter gives information on basic operations including using the TouchPad, optical media drives, the internal modem, LAN and wireless LAN. It also provides tips on caring for your computer and on heat dispersal.

Using the TouchPad

To use the TouchPad, simply move your finger tip across it in the direction you want the on-screen pointer to go.

Touch pad

Touch pad control buttons
Figure 4-1 TouchPad and control buttons The two buttons below the keyboard are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
CAUTION: Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against the TouchPad. The TouchPad could be damaged. The TouchPad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap the TouchPad instead of pressing a control button. NOTE: You can customize pointing device actions in Mouse Properties. Open the Control Panel, select the Mouse icon and press Enter to open the Mouse Properties window. Click Click the left control button or tap the TouchPad once. Double-click Click the left control button twice or tap the TouchPad twice. Drag and drop 1. Select the material you want to move. 2. Leave your finger on the TouchPad and move the material. 3. Lift your finger to drop the material where you want it. Scroll Vertical: Move your finger up or down the right edge of the TouchPad. Horizontal: Move your finger left or right along the bottom edge of the TouchPad.

Battery types

The computer has two types of batteries: Battery pack Real Time Clock (RTC) battery

Battery pack

When the AC adaptor is not connected, the computers main power source is a removable lithium ion battery pack, also referred to in this manual as the battery. You can purchase additional battery packs for extended use of the computer away from an AC power source. The battery is a disposable item. When its operation becomes short even when fully charged, replace it with a new one. CAUTIONS: 1. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the Battery Pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power, it will be lost. Battery type PA3307U-1BAS, PA3307U-1BRS, PA3367U-1BAS, or PA3367U-1BRS are for use with TOSHIBA notebook PC's, depending on the model purchased.

Real Time Clock battery

The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: ERROR 0271:Check date and time settings. WARNING 0251:System CMOS checksum bad - Default configuration used. Press <F1> to resume, <F2> to Setup CAUTION: The computers RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. When this error appears, the following action is recommended. 1. Connect the notebook to a mains power supply for around 24-hours to recharge the battery 2. Press F2 to enter BIOS setup menu 3. Set correct time and date CAUTION: There is a risk of explosion if the battery is replaced with an incorrect type. Please dispose of all used batteries as required by local ordinances or regulations.
Care and use of the battery pack
The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.

Safety precautions

Mishandling of batteries can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, which could result in death or serious injury, if you do not follow instructions. Warning: Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. Caution: Indicates a potentially hazardous situation, which if not avoided, may result in moderate or minor injury or property damage. Note: Provides important information. CAUTION: Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instruction.

Caution

1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery packs power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture. 3. Use only battery packs recommended by TOSHIBA as replacements. 4. Always make sure the battery pack is installed correctly and securely. Otherwise, a battery pack could fall out and possibly cause injury. 5. Charge the battery pack only in an ambient temperature between 5 and 30 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Standby Mode will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor. Never remove the battery pack while the computer is in Standby mode. Data will be lost.
1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power for an extended period, more than a week, the battery might fail to retain a charge. It might not function efficiently over the expected life of the battery pack and the Battery indicator might not indicate a low-battery condition. 3. After the battery pack is charged, avoid leaving the AC adaptor connected and the computer turned off for more than a few hours at a time. Continuing to charge a fully charged battery pack can damage the battery.

2. 3. 4. 5.

Figure 7-5 Removing the memory module socket cover 6. Fit the modules connectors into the computers connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
7. Push the module down so it lies flat. Latches on either side will click into place to secure the module.

Slot B

Slot A
Figure 7-6 Installing a module 8. Seat the cover and secure it with two screws. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes. 10. Turn the power on and make sure the added memory is recognized.

Removing memory modules

CAUTION: If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. To remove the memory module, make sure the computer is in boot mode then: 1. Be sure the power is off and all cables are disconnected from the computer. CAUTION: Do not try to remove a memory module with the computer turned on. You can damage the computer and the module. 2. Turn the computer upside down and remove the battery and two screws securing the memory module socket cover. 3. Slide your fingernail or a thin object under the cover and lift it off. 4. Push the latches to the outside to release the module. A spring will force one end of the module up.

Additional battery pack

5. Grasp the module and pull it out. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
Figure 7-7 Removing the memory module 6. Seat the cover and secure its screws. 7. Replace the battery.
You can increase the portability of the computer with additional battery packs. If youre away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.

Additional AC adaptor

If you frequently carry the computer to different sites such as your home and office, having an AC adaptor at each location reduces the weight and bulk of your load.

Parallel printer

You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cables connectors are designed so that it is impossible for you to connect them incorrectly. To connect a printer, follow these steps: 1. Turn off the computer. 2. Insert one end of the cable into the computers parallel port. 3. Tighten the screws that fasten the cable connector to the computers parallel port. 4. Insert the other end of the cable into the printers parallel connector. 5. Fasten the connector to the printer with the clips on the parallel port. 6. Turn on the printer. 7. Turn on the computer. 8. Windows XP may automatically recognize the printer and you can begin printing immediately. If it doesnt, install the printer with the Add Printer Wizard. To access the Add Printer Wizard, click Start, point to Printers and Other Hardware , click Printers and Faxes and double click the Add Printer icon.

1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: You may need to install drivers for your i.LINK devices. Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed. Use S100, S200 or S400 cables no longer than three meters. Some devices might not support standby or automatic off functions. Do not connect or disconnect an i.LINK device while it is using an application or when the computer is automatically shutting it down to save power. Data might be destroyed.

Security lock

1. Click the Eject or Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. NOTE: Refer also to the documentation that came with your i.LINK device.
A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.

Figure 7-8 Security lock

Chapter 8

Troubleshooting

TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

Problem solving process

Resolving problems will be much easier if you observe the following guidelines: Stop immediately when you recognize a problem exists. Further action may result in data loss or damage. You may destroy valuable problem-related information that can help solve the problem. Observe what is happening. Write down what the system is doing and what actions you performed immediately before the problem occurred. If you have a printer attached, print a copy of the screen using the PrtSc key. Isolate the problem. Using the tools available to you, such as the troubleshooting tips in this chapter, try to discover the specific actions that caused the problem. The questions and procedures offered in this chapter are meant as a guide, they are not definitive problem solving techniques. Many problems can be solved simply, but a few may require help from your dealer. If you find you need to consult your dealer or others, be prepared to describe the problem in as much detail as possible.

Preliminary checklist

Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device. Make sure all options are set properly in the setup program.

This section discusses problems caused by your computers hardware or attached peripherals. Basic problems may occur in the following areas: System start-up Self test Power Overheating power down AC Power Battery Password Keyboard LCD panel Hard disk drive SD card Wireless LAN DVD-ROM drive DVD-R/-RW DVDR/RW drive DVD Multi drive PC Card Printer Monitor Sound system Pointing device USB TV output signal Standby/Hibernation Memory expansion Modem i.LINK (IEEE1394) DVD Super Multi drive Drive LAN Infrared port Diskette drive

System start-up

When the computer does not start properly, check the following items: Self Test Power Sources Power-on Password

Self test

When the computer starts up, the self test will be run automatically, and the following will be displayed:
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the computers BIOS. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo. Random characters appear on the screen, and the system does not function normally. The screen displays an error message. Turn off the computer and check all cable connections as well as PC Card and memory module connections. If the test fails again, contact your dealer.
Hyper-Threading Technology Incompatibility
Some applications may not be compatible with Hyper Threading Technology (HTT). If an application does not work with HTT, try disabling it as described below. 1. Turn the computer on. 2. Press F2 to enter the BIOS setup menu when the TOSHIBA logo appears on the screen. 3. Under the Advanced menu, in Hyper Threading Technology, select Disable. 4. Save and Exit. 5. Reboot the computer. NOTE: Not all models come with HTT.
When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply, Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource. In such a case, contact your dealer.

Overheating power down

If the computers internal temperature becomes too high, the computer will automatically shut down.

Appendix C

Power Cable Connectors
The Satellite computer features a universal power supply you can use worldwide. This appendix shows the configuration of typical AC power cord plugs and sockets in various parts of the world.

USA and Canada

UL approved CSA approved

United Kingdom

BS approved

Australia

AS approved

Europe

VDE approved NEMKO approved

Appendix D

If Your Computer Is Stolen
Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer's machine type, model number, and serial number, and put this in a safe place. You will find this information on the underside of your notebook. Please also keep the receipt of the computer you purchased. Should your computer be stolen, however, we'll help you try to find it. Before contacting TOSHIBA, please prepare the following information which is necessary to uniquely identify your computer: In which country was your computer stolen? What type of machine do you have? What is the model number? What is the serial number? When was it stolen, i.e. date? What is the warranty seal number (if available)? What is your address, phone, and fax number? To register the theft, please follow these procedures: Fill in the TOSHIBA Theft Registration form (or a copy of it) below. Attach a copy of your receipt showing where your computer was purchased. Either fax or send the receipt and registration form to the address below. Your registration will be entered in a database, which is used to track TOSHIBA computers at our service points.
TOSHIBA Theft Registration
Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. Regensburg Germany +49 (0) 925
Fax number: Country stolen:
Machine type: (e.g. Satellite P20) Model number: (e.g. PSP20 YXT) Serial number: (e.g. 70123456E) Date stolen:
Warranty seal: (e.g. 049)
Owner's details Name: Company: Street: Postal Code/City: Country: Phone: Fax:

TOSHIBA Satellite P10/P20 Introduction to Windows Media Center Edition 2004

Contents

Media Center Setup.. 2
Connecting the Computer with an External TV Tuner to a Television.. 2 Connecting the Computer with an Internal TV Tuner to a Television... 3 Connecting the External Remote Sensor.. 4 Connecting the TV Signal Source.. 5 Connecting the TV Signal Source When You Have an Existing Setup.. 6
Starting the Media Center.. 8
Navigating Media Center... 11 Remote Control For Media Center.. 11 Remote Control Overview.. 12 Remote Control Overview.. 13 Remote Control Button Groups.. 15 Direct Access Buttons... 15 Media Playback Buttons.. 16 Using the Media Center Remote Control. 17

Watching Television.. 18

Selecting a Program from the TV Guide. 20 Watching a Recorded TV Program. 21 Searching for a TV Program. 22
Recording TV Shows.. 23 Recording TV tips.. 24
Recording from the Guide.. 25 Recording from Search.. 25 Recording Manually.. 26 Changing Your Settings.. 27 Changing recording priorities.. 28

Listening to Music.. 29

Creating Your Music Library Using Windows Media Player... 30 Deleting Music Files.. 31 Adding Music from Your Hard Drive to Windows Media Player Library.. 31 Playing Digital Music Files.. 32 Finding Music Files in My Music. 33 Playing a Song.. 33 Setting Up an Automatic Disc Jockey.. 34 Finding and Playing an Album.. 34 Creating a Play list... 35
Displaying Your Pictures. 36
Viewing a Slide Show... 37 Sorting your Pictures.. 37
Watching Your Digital Movies.. 38
Organizing Your Videos.. 39
Playing Digital Videos... 40 Playing a Video in Full Screen Mode.. 41 Sorting Videos.. 41

Watching a DVD.. 42

Stopping a DVD Movie.. 43 Playing a DVD movie already in your drive. 43
Changing the Media Center Settings.. 44
Administrator Controlled Settings.. 44 User Controlled Settings.. 45 Changing General Settings.. 45 Changing TV Recorder Settings.. 46 About Recorded TV Storage Settings.. 47 Change TV Guide Settings.. 48 Changing Parental Controls for TV Viewing. 49 Changing DVD Movie Language.. 50 Selecting Closed Captioning.. 50 Changing Picture Settings.. 51

Index... 52

Safety precautions

Danger

TV tuner
Do not attempt to disassemble, modify or repair the TV tnuer. Ii could result in fire. Contact your dealer or service center for repairs. Never leave the plastic bags that were used for packaging the TV tuner or any of its components in places where children or infants can reach them. Plastic bags are a suffocation hazard for children and infants. Never leave small parts such as covers, caps or screws within the reach of infants or small children. Swallowing a small part may cause choking and suffocation resulting in death or serious injury. Consult a doctor immediately if a small part is swallowed or take whatever emergency action is appropriate. Do not place the TV tuner next to cups or other containers of liquid. Do not place staples, paper clips or similar metal objects on it. If foreign materials, such as liquids or metal, get into the TV tuner, it could cause fire or electric shock. If foreign matter gets inside the tuner, immediately disconnect the AC adaptor from the system. Take the TV tuner to your dealer or service center. Do not use or place your TV tuner in a bathroom or area exposed to water from a shower or area with high humidity. Do not expose it to rain or mist outdoors. It could cause fire or electric shock.

Caution

Follow the instructions in this guide when connecting or disconnecting. Do not disassemble the TV tuner in any manner not described in the manual. It could result in fire, burns or electric shock. If there is expectation of lightning, disconnect the antenna. If you hear thunder, do not touch the TV tuner or cables connected to it. There is a possibility of electric shock.

Notes on usage

Do not place the TV tuner in direct sunlight, in a hot closed car, near a heater or in any other way exposed it to high temperatures. It could result in damage, malfunction. Do not expose the TV tuner to cold temperatures. It could result in damage or malfunction. Do not place the TV tuner in areas with high dust levels. It could result in damage or malfunction. If dust gets inside the TV tuner, take it to your dealer or service center. Do not expose the TV tuner to sudden changes in temperature. It could cause condensation resulting in damage or malfunction. Do not place the TV tuner close to magnets, speakers, TVs, magnetized bracelets or other devices that create magnetic fields, It could result in damage or malfunction. Do not place or drop objects on the TV tuner. It could damage the tuner. Do not user benzene or thinner to clear the TV tuner. It could cause warpage or discoloration.

The Media Center main window is the central point for controlling all Media Center features. With a quick click of the mouse or using your remote control, you can: Watch or record TV programs Listen to music Display your digital photos Watch your own digital movies Watch a DVD movie Change your Media Center Settings Check out the Online Spotlight Look at More Programs When enjoying the Media Center, use the icons on the Manual Bar to return to the Media Center main screen, go back to the previous screen, or to display the Media Centers online help.
Use the Media Center Controls Transport tool bar at the bottom of the screen to control your movies, music, and photo displays.

Media Playback controls

Navigating Media Center
In the Media Center windows, a selected item, such as a folder, file, or menu item is outlined with a green border. To select items, use the arrow buttons on the remote control, and then the OK button to enter your selection. If you have media playing, such as music or a television program, it displays in an inset window in the lower left corner. To switch from watching your media in the inset window to watching it in full screen mode, use the arrows on the remote control to select it and then press OK.
Remote Control For Media Center
You can use your remote control with Media Center to play CDs, DVDs and videos; to view pictures; and to watch and record television programs. The remote control helps you navigate the Media Center windows on your computer just as a cable TV remote control navigates cable TV options or controls the playback of a movie in a VCR or DVD player. Using the remote control, you can: Navigate and control all Media Center windows. Control the video or live TV display. Place the computer in and out of Stand By mode. The remote control can send a strong signal to the remote sensor from within a range of about 26 feet and from an angle of about 45 degrees.

Remote Control Overview

The Remote Control
Sleep - Puts the computer into either Stand By or Hibernation mode, depending upon your computers settings. Record - Records the selected television program and stores it on your hard disk. Stop - Stops the media currently playing. REW (Rewind) - Moves the media backwards. Play - Plays the selected media. FWD (Fast forward) - Moves media forward.

The Remote Control (P20)

Replay - Moves media backward (seven seconds for videos and live TV, one music track or one DVD chapter at a time). Pause - Pauses an audio or video track, and live or recorded TV programs. Skip - Moves media forward (30 seconds for videos and live TV, one music track or one DVD chapter). Start - Opens Media Center to the main window.
Back - Displays the previous window. Guide - Opens the Television Program Guide to display available TV channels and programs to watch and record. Arrow buttons - Moves the cursor to navigate within Media Center windows. OK - Selects the desired action or window option. It acts like the Enter key. If watching TV in full screen mode, pressing OK switches back to the previous viewed channel. Press again to toggle back. It acts the same way as a Jump button on some TV remote controls. Live TV - A shortcut to the full screen view. It also takes you to the current point in a live TV program after pausing live TV. More Info - The button provides more details on a TV program that is listed in the Guide. My Videos - Opens the My Videos window. My Music - Opens the My Music window. My TV - Opens the My TV window. My Pictures - Opens the My Pictures window. Volume - Increases (+) or decreases (-) sound. Mute - Turns your computer sound off. Channel/Page up (+) and down (-) - Changes the TV channel or moves a page up and down, depending on the available options. DVD Menu - Opens the main menu on a DVD movie, if available. 0 to 9 - Changes channels or enters text into a Media Center search or text box. Clear - Deletes the current selection and acts like a backspace key on a keyboard. Enter - Selects the desired action or window option.
Remote Control Button Groups
Use your remote control to navigate all the Media Center windows. Your remote control includes four major groups of controls. Stand By and Direct Access - The Sleep button places the computer in and out of Stand By or Hibernation (reduced power) mode, depending upon your computers configuration. The direct access buttons open specific windows within Media Center. Media playback - The media playback buttons control the playback of music, DVD movies, videos, recorded and live TV programs, and picture slide shows. Navigation and other direct access - The navigation buttons move the cursor around Media Center windows and select desired actions, much like a mouse does. The other direct access buttons open specific windows within the Media Center, such as the Television Program Guide, a DVD main menu, and live TV in full screen mode. Audio and Video - The audio and video buttons control sound and channel selection, display details, and allows you to enter text.

Direct Access Buttons

The direct access buttons open the main Media Center windows. TV opens the My TV window where you can watch and record TV and access other My TV features. Recorded TV opens the Recorded TV window where all your recorded TV programs are stored. From this window, you can search for and play back a recorded show. Music opens the My Music window where you can play music CDs and your music files. Pictures opens the My Pictures window where you can search for, sort, and view pictures and slide shows that are stored in the My Pictures or the Shared Pictures folder in Windows Explorer. Video opens the My Videos window where you can search for, sort, and play back your recorded video files that are stored in the My Videos or the Shared Videos folder in Windows Explorer.

Media Playback Buttons

These buttons allow you to play back picture slide shows, music files, playlists, music CDs, DVD movies, home videos, and live TV, from within the Media Center program. Use Pause to pause selected media. Press Pause and then FWD repeatedly to play media frame by frame in slow motion. To continue slow motion, you must press the FWD button more than once. Use Play to play selected media. Use FWD to move selected video or picture media forward. Press FWD up to three times to increase the fast forwarding speed. Pressing the FWD button: Move pictures forward to the next picture. Move a video forward. Move a TV program (that has been paused or stopped) forward to the current moment in live TV, and then begins playing. Use REW to rewind selected video or picture media. Press REW again to increase the rewinding speed. Pressing the REW button: Moves the picture slide show backward to the previous picture. Moves the video backward. Moves live TV program to the beginning of the 30- minute pause buffer. Use Record to record TV programs. The Record button works only when My TV is used to play a TV show. It is inactive when other media is playing. While watching live TV or in the Guide, you can press the Record button once to record a TV show. In the Guide, you can press Record twice to record a TV series. In the Guide, press Record three times to cancel recording.
Use Stop to stop selected media from playing. When this is pressed while you are watching TV, the Media Center pause buffer continues to record in the background. Use Skip to move forward in the selected audio or video file. For music, Skip moves to the next track. For DVDs, Skip moves to the next chapter. For videos and live TV and videos, Skip moves ahead 30 seconds. Use Replay to move backward second seconds in the selected audio or video file. For music, Replay moves to the previous track. For DVDs, Replay moves to the previous chapter. For videos and live TV and videos, Replay moves back 7 seconds.

My TV Guide screen

Use the arrows at the top of the screen to display programs for later or earlier in the day. Use the arrows at the bottom of the screen to display additional channels available for viewing. Use the remote control CH/PG keys to scroll the listing To view a program, double-click it, or select it with the remote control and click OK. If the desired program is currently playing, the inset window will maximize and the program will play.
Watching a Recorded TV Program
Recorded TV is the storage place for all your recorded programs. In the Recorded TV window, you can sort your shows by name, date, or status. You can also delete a recorded program or series of programs and check for any recording errors. To watch a previously recorded TV program, on the My TV screen, click Recorded TV. On the remote control, click Start, and then My TV, and then select Recorded TV.
All of your recorded TV programs display on the Recorded TV screen. You can sort your programs by Date, Category, or Name by clicking the desired sort option. Select Scheduled to view a list of all programs scheduled to be recorded. You can also resolve any recording conflicts in this window. Use the arrow buttons to move through the list, select a program, and then press OK on the remote control. Select the option to change, and then press OK again. Using the arrow buttons, select the recorded program you want to watch, and then press the OK button on the remote control to begin watching the program.
Searching for a TV Program
You can search the TV Guide to find a TV program by entering a title, keyword, or by selecting a category using your remote control. To search for a TV show: 1 Press the Start button on the remote control, select My TV, and then select Search. 2 Do one of the following: Select Title. Use the numeric buttons on your remote control to enter a program title word, and then press OK on the remote control. Select Keyword. Use the numeric buttons on your remote control to enter a descriptive word that would appear in a program title or program description, and then press OK on the remote control. 3 Use the arrow buttons to scroll through the search results, select a show, and then press OK. If multiple times for the show are displayed, select a time and press OK. 4 Select Play in the window, and then press OK on the remote control to begin watching the program in full screen mode. If the show is not currently playing, select Record Show or Record Series, and then press OK.

Recording TV Shows

The Media Center allows you to record TV programs for later viewing. You can record the show you are watching, or you can record another or future show or series from the Guide, the Search, or the Settings window in My TV. To record a TV show you are currently watching, just press the Record button on the remote control once. The Record icon appears in the Guide next to the program being recorded or the program to be recorded. If a show is currently being recorded, the Record icon also appears in the taskbar on the desktop. If you move your mouse over the icon, the Media Center displays which show is currently being recorded. You can right-click the icon to open Media Center and stop recording. Media Center automatically records until the show is scheduled to be over as listed in the TV Guide. To make sure your show is being recorded, you can select TV Guide. The Record icon should appear next to the show in the TV Guide while you are recording. The Record icon disappears when the recording is complete. If there is a recording conflict or error, the Record Conflict icon appears next to the show in the TV Guide. This means the show will not be recorded unless the conflict is resolved.

Recording TV tips

If you are watching live TV during a scheduled recording time, you can watch only the show being recorded. If you change channels, the recording stops. If you go to another area in the Media Center, the TV channel you last selected will be displayed in the inset window at the bottom of the window. When scheduling a recording in the TV Guide, you can press the Record button once to record a show, twice to record a series, or three times to cancel a scheduled recording you just selected. When you press the Record button to record a show you are watching, the recording automatically stops at the end of the show's regularly scheduled end time. Some channels can be shared by two or more networks, It depends on the time of day. The Guide may display only one network's programming. This may cause recording options to be unavailable. You may need to manually update the Guide before scheduling a recording. NOTE : If you turn off (shut down) your computer, the Media Center will not record a scheduled program. Your computer must be turned on or in Stand By mode to record a TV program. The computer will not automatically go into Stand By mode if the Media Center is open.

Recording from the Guide

To record a current or future show or series from the Guide: 1 Press the Start button on the remote control, select My TV, and then select Guide. 2 Use the arrow buttons on the remote control to find the show you want to record, select the show, and then press OK. You can also press the numeric buttons on the remote control to go directly to a channel. Press the right arrow button in the Guide to select a show that will be broadcast in the future. 3 Select Record in the window and press OK on the remote control to record the show. The Record icon appears next to the show in Guide. You can also select Record Series and press OK on the remote control to record the entire series. The Record Series icon is displayed to indicate a series. 4 Press Back on the remote control to return to the previous window. If there is a recording conflict, Media Center displays a message and allows you to select which show you want to record.

Recording from Search

To record a current or future show or series using Search: 1 Press the Start button on the remote control, select My TV, and then select Search. 2 Select Title, Keyword, or Categories. For Title and Keyword searches, enter your descriptive search words. The Media Center starts searching from the first letter you type into the text box. For a Categories search, select the category you want and press OK. 3 Use the arrow buttons to scroll through the search results to select the show you want to record, select the show, and then press OK. 4 Select Record or Record Series in the window, and then press OK. The recording icon for a single program or the recording icon for a series appears next to the show in the Guide.
5 Press Back on the remote control to return to the previous window. If there is a recording conflict, the Media Center displays a message and allows you to select which show you want to record.

Recording Manually

Recording a program manually allows you to select a specific date, channel, and recording time period. For some programs, you may want to begin recording before the scheduled beginning and after the scheduled ending of the program. To manually record a show or series: 1 Press the Start button on the remote control, and then select My TV. 2 Select Recorded TV. 3 Select Add Recording. 4 Enter the channel number using the numeric buttons on the remote control. 5 Under the Create a custom recording with area, select Channel and time. Use the arrow buttons on the remote and +/- buttons on the screen to bring the selections into focus. 6 Select Add title if you would like to name the manual recording. Enter letters by using the numeric keypad on the remote to name the recording, and then select Save. 7 Select Record to schedule the manual TV recording and return to the Recorded TV menu.

Changing Your Settings

The Media Center Settings option allows you to: Change settings for your television service provider. Change settings for your Internet Service Provider. Manually update the My TV Television Program Guide. Check your remote control. Change your ZIP Code to receive the correct Television Program Guide for your area. To change settings, on the My TV screen, click Settings.

TV Settings screen

This window allows you to change several settings that control how Media Center plays and records TV programs, as well as how it plays DVDs. In particular, you can change settings for: Recording a TV program, including manually recording The TV Guide The TV Signal Adjust display settings Audio settings To make a change, click on the desired setting.

Finding Music Files in My Music
After you have added and organized files in Windows Media Player Library, you can browse through your music files in the My Music window. You can search for music files by album title, artist, song title, or music genre. You can also use the search feature to quickly find a specific song, album, or artist. To find a music file: 1 In the My Music window, select Albums, Artists, Playlists, View Songs, or Genres to display a list of all items in that category. In these windows, you will have other options, depending on the category you select. Or Select Search. Use the numeric buttons on the remote control to enter a descriptive word, song title, or artist name and display a list of all the titles that match your entry. 2 Use the arrow keys to select a music file, and then press the Play button on the remote control to begin playing that music file. If you back up music files from a CD using Windows Media Player 9, you must log the files into the media player's play list before you can play them using the Media Center. To log the files into the play list, open indows Media Player 9, press F3 and log the files in the dialog box.

Playing a Song

You can play a song from anywhere in My Music. You can select it from the View Song list, or from the Album, Artist, and Genre lists. You can also play a single song from a playlist as follows: 1 In the My Music window, select Album. The list displays all the songs in your media library. 2 Use the arrow buttons to select a song, and then press OK or Play on the remote control to play it. 3 Use the controls at the bottom of the screen to stop or pause the song, advance to another song, or increase or decrease the volume.
Setting Up an Automatic Disc Jockey
You can select to have Media Center randomly play all the available songs in one genre: 1 In the My Music window, select Genres. The list displays all the genres available in your Media Library. 2 Use the arrow buttons to select a genre, and then press OK on the remote control. 3 Use the arrow buttons to select Shuffle, and then press OK on the remote control. All songs in that genre are randomly played.
Finding and Playing an Album
1 In the Media Center Start menu, select My Music, and then select Albums. 2 In the Albums window, select View by list or View by cover to organize all of the albums available. 3 Use the arrow buttons to select an album, and then press OK on the remote control. You can also select: Shuffle to rearrange the music tracks on the album. Play to play the album selected. The Now Playing window opens, and the album starts playing. 4 In the Play window, select a song and press OK on the remote control. You can also select: View Song to view cover art and play one track. View Tracks to view a list of all tracks on the album. Shuffle to rearrange the play order. Repeat to play the album again. Buy Music to connect to the Internet, find CD information, and buy music CDs. To go back to Media Center, press Start on the remote control. 5 Press Back on the remote control to return to the previous window.

Sorting your Pictures

To organize your pictures by date or by name: 1 Select My Pictures on the Media Center Start menu. 2 Select Sort by date or select Sort by name.
Watching Your Digital Movies
The My Videos window in the Media Center makes it easy to play home video files you created or video files you downloaded from the Internet. In My Videos you can: Browse through and play back all of your digital video files using the remote control or the keyboard and mouse. Sort videos by name or date. View your videos in full screen mode or from an inset window in Media Center.

My Videos screen

Organizing Your Videos
When you attach a digital video camera to your PC, Windows asks you how you want to capture your video. You can choose from various software programs to capture and then edit your video file. Most programs automatically save your file to the My Videos folder in Windows Explorer. If not, move your videos into the My Videos or Shared Videos folder in Windows Explorer for Media Center to be able to find and play them. Once you have placed all your videos into the My Videos or Shared Videos folder, you can rename, add, delete, and organize them into folders. To organize and store your videos, click Start on the taskbar, click My Documents, and then double-click the My Videos folder. If you want to share your videos with others, place them in the Shared Video folder. To do this, click Start on the taskbar, click My Documents, click the Shared Documents folder under Other Places, and then double-click the Shared Video folder. You can add, delete, edit, rename, and organize your video files into folders you create in the Shared Video folder. Your videos can now be played in Media Center.

Playing Digital Videos

After you organize your videos in the My Videos or Shared Videos folder in Windows Explorer, open Media Center to watch your videos. 1 Press the Start button on the remote control to open the Media Center Start menu. 2 Select My Videos. The right side of the window shows small images of your video files and folder icons, if you've organized your videos into folders. 3 Use the arrow buttons on the remote control to move through and select your video or video folder. 4 Press the OK button on the remote control. The selected video plays in full screen mode, or the folder opens displaying a list of video files. Use the mouse to resize the window if you want to watch your video while doing something else on your desktop. 5 When the video is finished, select Restart and then press OK to replay the video. You can also select Done and press OK to close the file and return to the My Videos window.

Playing a Video in Full Screen Mode
1 On the Media Center Start menu, select My Videos. 2 On the My Videos menu, select My Videos or Shared Video. 3 Use the arrow buttons to select the folder you want, and then press OK. Select the video file and press OK again. Your video plays in full screen mode. 4 Press Back on the remote control to exit full screen mode and return to the previous window.

Sorting Videos

To organize your videos by date or by name: 1 On the Media Center Start menu, select My Videos or Shared Video. 2 If your videos are organized within other folders, use the arrow buttons to select the folder you want to sort, and then press OK. If you don't select a folder, the Media Center sorts all the files and folders. 3 Select Sort by date or Sort by name.

Watching a DVD

Watching DVDs in the Media Center allows you to control the playback with your remote control. If you select to play your DVD in another program, the use of some of the remote control buttons is not supported. To play a DVD movie in Media Center 1 Insert the DVD into the drive. If you have other media playing, Media Center asks if you want to play the DVD. Select Yes or No. If you select Yes, the DVD automatically plays in full screen mode after a few seconds. 2 If a DVD menu appears, use the remote control or the mouse to select the DVD menu items and control the DVD movie playback. 3 Press Stop on the remote control to stop playing the DVD. 4 To change the window size, move the mouse and click the Resize button on the taskbar of the DVD window.

Play DVD screen

Stopping a DVD Movie
1 Press the Stop button on the remote control to stop the movie. 2 Use the arrow buttons on the remote control to select an item on the Stopped menu, and then press OK. Select Resume to begin playing the DVD where you left off. Select Restart to begin playing the DVD at the beginning. Select Title Menu to go to the DVD main menu, if available. Select DVD Languages to change the language for the DVD soundtrack, subtitles, and menu. Select Eject to open the disc tray.

Playing a DVD movie already in your drive
If you already have a DVD movie in your drive, but you have been doing other things in Media Center or in other programs from your desktop, you can play the DVD by: 1 Press the Start button on the remote control. 2 Select Play DVD. The DVD movie begins playing in full screen mode.
Changing the Media Center Settings
In the Media Center Settings window, you can change settings for watching television, for viewing your pictures and slide shows, and for controlling sound and the display of all the Media Center windows.
Media Center Settings screen
Administrator Controlled Settings
Some settings apply to all Media Center windows for all users and must be set up by the administrator. These settings are: Parental Control sets up rating permissions for TV viewing. This setting requires the administrator to use a separate password. This option may not be available with your model. Set up Internet connection sets up Internet connection. Guide sets up channel mapping for the Television Program Guide, which enables your computer to download the correct guide from the Internet. Setup TV signal sets up your TV or cable connection.

User Controlled Settings

Some settings can be selected by each person using the PC. These settings are: Sounds, Appearance, and Audio sets sound and display settings. DVD sets language and audio settings for playing DVD movies. Pictures determines slide transition time and selects which pictures to display in a slide show.
Changing General Settings
General settings affect each user's experience in Media Center and can be changed only by the administrator of the computer. 1 In the Media Center Start menu, select Settings. You may need to select the scroll arrows in the Start menu to view Settings. 2 In the Settings window, select General. 3 In the General window, do one of the following: Select Appearance to turn transition animations or notifications on or off, as well as text and colors for the computer monitor or television screen. Use the arrow buttons to select the item to change, and then press Save. Select OK in the window, and then press OK again. Select Media Center Sounds to turn the sound on or off. Use the arrow buttons to select an option, and then press OK on the remote control. Select Save in the window, and then press OK again. Select Notifications to turn on or off taskbar notifications. When on you receive a notification when you are low on disk space, when there is no TV signal, or when there is no Guide data. Select Autoplay to set autoplay options. Select Parental Control to set passwords, movie ratings, and other controls.
Select Set up Internet connection to open the Internet Connection wizard. This allows you to set up your connection. Follow the on-screen instructions. Select Set up Remote Control to make sure your remote control is working with the remote sensor. Follow the on-screen instructions. Select Privacy to change settings for how the computer retrieves and stores media information. Select Data Credits to find information about your version of Media Center. 4 Press the Back button on the remote control to return to the main Settings window.

Changing TV Recorder Settings
The TV Recorder settings allow you to control your recording priorities and options in Media Center. 1 In the Media Center Start menu, select Settings. 2 Select TV. 3 Select Recorder. Select History to check a list of scheduled recordings, delete scheduled recordings, resolve recording conflicts, and to change recording priorities for the programs you scheduled to record. Select Recording storage to check the amount of recording space on your hard disk. Also, you can change the settings that affect the recording storage space. Select Recording defaults to change the general recording default settings that affect how and when your programs are recorded. 4 To change the TV/DVD settings, use the arrow buttons to select an option, and then press OK on the remote control. Select OK in the window and then press OK on the remote control again to enter the changes. 5 Press the Back button on the remote control to return to the main Settings menu.
About Recorded TV Storage Settings
The space available for recording TV programs depends on your hard disk allocation, drive size, and default recording quality selections. Your PC requires a certain amount of space to run your Windows XP operating system, run software programs, and store data files. If your hard disk becomes full, it may affect the PC speed and performance. You may need to free up storage space to record more programs or to optimize the PC's performance. To increase disk space, you can: Delete recorded shows from the Recorded TV window. For more information, refer to the My TV chapter. Increase the percentage of hard disk space available for recorded TV shows in Default Settings. Select between 5 percent and 90 percent. The default is set at 45 percent. Record TV programs to the largest drive. Media Center does not support removable drives, network drives, or drives with less than 5 MB of disk space. Archive TV programs to a DVD+RW or DVD+R if your PC has a DVD writer drive. You can play archived programs recorded on DVDs only from the PC that you recorded the TV program from. In the Recorder Defaults window, select Fair as the default recording quality. The better the quality of the recording, the more space the file takes. In the Recorder Defaults window, select Until I watch as the Keep setting for each recorded show.