TD-8610/TD-8610B External ADSL2+ MODEM

Rev: 1.0.2 1910010011

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2008 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) 2) This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Package Contents

The following contents should be found in your package: One TD-8610/TD-8610B External ADSL2+ MODEM One AC power Adapter for TD-8610/TD-8610B External ADSL2+ MODEM One RJ45 cable Two RJ11 cable One ADSL splitter (only available for TD-8610) One Resource CD for TD-8610/TD-8610B External ADSL2+ MODEM, including: This User Guide Other Helpful Information
Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.

CONTENTS

Chapter 1.
1.1 1.2 1.3 1.4 1.5 1.6 1.7

Product Overview...1

Product main specification....1 Supporting protocol...1 Transmit data-rate...1 ATM property...2 System support....2 Working environment...2 Electric parameter...2

Chapter 2.

2.1 2.2 2.3 2.4
Hardware Installation Guide..3
System requirement....3 LED explanation...3 Rear-panel....4 Hardware installation procedures..4

Chapter 3.

3.1 3.2 3.3 3.4

How to use...6

Computer Configuration...6 Login....7 Setup....8 Software Dial...9
Appendix A: Default Configuration..10

TD-8610/8610B

External ADSL MODEM
Chapter 1. Product Overview
With the excellent design of circuit and high quality production, we guarantee ADSL2+ MODEM a high performance, very good stability and easy to use. TD-8610/TD-8610B is a complete plug-and-play solution. With standard Ethernet interface, it can be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX. TD-8610/TD-8610B not only use html (web mode through Ethernet port) to configure the MODEM but also use external utility software too. You can download it from our website (http://www.tp-link.com).

1.1 Product main specification
High speed and asymmetry data transmit mode, adapt to wide-band internet access Point to point connection, provide safe and exclusive bandwidth Support All ADSL industrial standards Advanced DMT modulation and demodulation Firmware upgradeable Compatible with all mainstream DSLAM (CO) Real-time Configuration and device monitoring Quick response semi-conductive surge protect circuit, provides reliable ESD and surge-protect function

1.2 Supporting protocol

- G.992.1 (G.dmt) - Annex A/B - G.992.2 (G.lite) - Annex A/B - ANSI T1.413 - G.992.3 (ADSL2) - Annex A/B compliant - G.992.5 (ADSL2+) Annex A/B compliant - ADSL dual latency (fast path and interleaved path) - I.432 ATM physical layer compliant -Supports RFC2516 (PPPoE) * - Supports RFC1483 (EoA) ( Bridged) Note: *Need third-party software.

1.3 Transmit data-rate

Max download data-rate: 24Mbps 1
TD-8610/8610B Max upload data-rate: 1Mbps Max line length: 6Km

1.4 ATM property

AAL0, AAL5, OAM, RM, and raw cell types supported Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in software Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)

1.5 System support

Support PVC Support IEEE 802.3IEEE 802.3u Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet Support Auto-MDIX

1.6 Working environment

Operating temperature: 0~40 Storage temperature: -40~70 Humidity: 10%90%

1.7 Electric parameter

Adaptor power Output: 9VAC/0.8A50Hz or 60 Hz Power consumption: 4W Maximum
Chapter 2. Hardware Installation Guide

2.1 System requirement

Confirm your computer has been installed with networking interface card (NIC) before connecting ADSL MODEM to your computer, with operating system supporting the TCP/IP protocol.

2.2 LED explanation

The panel of ADSL MODEM includes one power button, one power indicator (RED) and four function indicators (GREEN), and these five indicators are explained as chart 1-1: Name Power On Off On Act Off On Alarm Off Slow flash ADSL Quick flash On Off On LAN Off Flash Status Power OK Power fail There is data transmitting or receiving on WAN port No data transmitting or receiving on WAN port There is a mistake when ADSL is transmitting data or receiving data ADSL normal Self-detecting when power up The LINE port is sending or receiving ADSL data The LINE port has connected to ISPs network The LINE port is disconnected LAN port is normal Connection on LAN port is abnormal Data is transmitting or receiving on LAN port Chart 1-1 Indication

2.3 Rear-panel

ON/OFF: Turn on/off the ADSL modems power. Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise that may cause damage to your ADSL MODEM. RESET (reset default): When the device is working, please press the reset button of the Modem, keep the reset button pressed down for more than five seconds and then wait for the router to reboot. LAN: Connect with your computers NIC. LINE (WAN): Connect to the MODEM of Splitter or connect to the telephone line.
2.4 Hardware installation procedures
First Step: Connect the MODEM of Splitter with the LINE port of the TD-8610/TD-8610B ADSL2+ MODEM by telephone line. While you need to use a telephone, please attach telephone line into the phone of Splitter. Second Step: Connect category 5 cable with RJ45 jacks to ADSL MODEMs LAN port and your computers NIC. Third Step: Link power adapter into the power jack of ADSL MODEM. Please note the range of voltage of power adapter should be within AC 220230V, 50Hz, which will make the MODEM under normal operation. Last Step: Check the line connection to see if everything is ready. Then power up.

Figure 2-1

Chapter 3. How to use
3.1 Computer Configuration
1. 2. Connect the cable according to Chapter 2, and then turn on the power. Change the IP address of your PCFigure 3-1: Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
Figure 3-1 Note: 1) The users of Windows 98 can open TCP/IP Properties according to the following: Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP. PCI Fast Ethernet Adapter. 2) The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor -> 6
Choose Properties -> Right-click Local Connection -> Choose Properties -> Double-press Internet Protocol (TCP/IP). 3) The words in fact maybe are different with this guide.
You can check whether your configuration is successful through PING command. Enter Ping 192.168.1.1 If the screen likes the following, your configuration is successful.
Figure 3-2 If the screen likes the following, your configuration is unsuccessful. Please repeat the previous steps again.

Figure 3-3

3.2 Login

Startup Internet Explorer, and enter 192.168.1.1; then enter user name (admin), password (admin), you will see the page (Figure 3-4). When ADSL connection is OK, you will see some information such as link rate.
Figure 3-4 The default user name and its password is admin; if you want to change it, please go to "ManagementPassword". (Figure 3-5)

Figure 3-5

3.3 Setup
1) 2) Choose ATM PVCs Configuration (See Figure 3-6) Enter the VPI/VCI value which is provided by your ISP, click Save to finish the configuration. You can press Next to add VPI/VCI value. 8

Figure 3-6

3.4 Software Dial
TD-8610/TD-8610B works in bridged (RFC 1483 Bridged) mode to connect to the Internet. You need to install dial software on your PC. There is some software working on WINDOWS in market, example for EnterNet3000, RASPPPoE and WinPeET.
Appendix A: Default Configuration
USER NAME PASSWORD IP ADDRESS VPI/VCI admin admin 192.168.1.1 0/32,1/33,0/35,0/100,0/200,8/35,8/81