108M Wireless Access Point TL-WA601G
Adopts 2x to 3x eXtended Range and 108M Super G technology, Much faster and further than ordinary 11g products
Supports multiple operating modes (Access Point, Client, Universal/ WDS Repeater, Wireless Bridge)
Advanced wireless encryption ensures data security

Description

The TL-WA601G is a 108M wireless access point compliant with 802.11b and 802.11g standards. It provides the access from the wireless station to wired LAN and vice versa; It can also be used to extend the wireless range. If you find the signal of your wireless router is not strong enough to cover your entire house or office, you can use the TL-WA601G as a repeater to repeat the wireless signal from your wireless router to the APs location; To build a wireless connection between two buildings, you can use two of this access points to work as a bridge. With so many different functions such as AP, AP Client, AP + Bridge, Bridge, and Universal / WDS Repeater, the TL-WA601G is ideal for a diverse number of complex network environments.

www.tp-link.com

Specifications
Standards Interface Wireless Signal Rates With Automatic Fallback Frequency Range Wireless Transmit Power Antenna Modulation Technology IEEE 802.11g, IEEE 802.11b 1 10/100M auto-sensing LAN Port Super G : 108M 11g: 54/48/36/24/18/12/9/6M(dynamic) 11b: 11/5.5/2/1M(dynamic) 2.4-2.4835GHz 20dBm(Max) 3dBi detachable Omni directional antenna IEEE 802.11b: DQPSK, DBPSK, DSSS, and CCK IEEE 802.11g: BPSK, QPSK, 16QAM, 64QAM, OFDM 108M: -68dBm@10% PER 54M: -68dBm@10% PER Receiver Sensitivity 11M: -85dBm@8% PER 6M: -88dBm@10% PER 1M: -90dBm@8% PER 256K: -105dBm@8% PER Power Supply Unit Operating temperature Storage temperature Relative humidity Storage Humidity Dimensions Input: localized to country of sale Output: 9VAC / 0.8A linear PSU 0C~40C (32F~104F) -40C~70C (-40F~158F) 10% ~ 90%, non condensation 5%~95% non-condensing 6.24.31.3 in. 15811032 mm

Features

Supports 108/54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps wireless LAN data transfer rates Adopts 2x to 3x eXtended Range and 108M Super G wireless LAN transmission technology Provides 64/128/152-bit WEP encryption security, WPA/WPA2 and WPA-PSK/WPA2-PSK authentication and TKIP/AES encryption security, Supports MAC address filtering Built-in DHCP server supporting dynamic IP address distributing Supports multiple operating modes (Access Point, Client, Repeater, Point to Point, Point to Multi-point) Supports Traffic statistics Supports firmware web-site upgrade, Web-Site management Detachable Antenna (reverse SMA connector)

Diagram:

Wired Wireless

Package:

Internet
- 108M Wireless Access Point TL-WA601G - 3dBi detachable Omni directional antenna - Power supply unit (localized to country of sale) - Resource CD - Quick Setup Guide
108M Wireless USB Adapter

TL-WN620G

TL-WN610G
108M Wireless Cardbus Adapter

TD-8810

ADSL2+ Router

Related Products:

AP Mode

TL-WA601G

Repeater Mode
108M Wireless PCI Adapter

TL-WN651G

108M Wireless Router TL-WR641G 108M Wireless PCI Adapter TL-WN651G External ADSL2+ Router TD-8810 SOHO Cable/DSL Router TL-R460
Specifications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specificationsmay be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co., Ltd.
Copyright 2009 TP-LINK Technologies Co., Ltd. All rights reserved.

2.1 The Front Panel

Figure 2-1 The LED indicators displayed on the front panel, the status of these LED indicators represent the devices working circs. For details, please refer to 2.1.1 LED Explanation

2.1.1 LED Explanation

Name Power Status Off On Off System On Flashing Off LAN On Flashing WLAN Off Flashing No Power Power on The AP has a hardware error The AP is initialising The AP is working properly There is no device linked to the corresponding port There is a device linked to the corresponding port but no activity There is an active device linked to the corresponding port The Wireless Radio function is disabled The Wireless Radio function is enabled Description

The Back Panel

Figure 2-2 3
TL-WA601G Wireless antenna Factory Default Reset button
There are two ways to reset the AP's factory defaults: Use the Factory Defaults function on System Tools -> Factory Defaults page in the AP's Web-based Utility. Use the Factory Default Reset button: First, turn off the AP's power. Second, press and hold the default reset button then turn on the AP's power, until the system LED lights up (about 3 seconds). Last, release the reset button and wait for the AP to reboot.
Note: Ensure the AP is powered on before it restarts completely. One LAN 10/100Mbps RJ45 port for connecting the AP to hub or switch AC power socket: only use the power adapter supplied with the TL-WA601G 108Mbps Wireless Access Point, use of a different adapter may result in product damage.

System Requirements

Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector A Ethernet broadband router TCP/IP protocol must be installed on each PC Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later 802.11g or 802.11b-compliant devices, such as the TL-WN510G Wireless Adapter
Installation Environment Requirements
Not in direct sunlight or near a heater or heating vent Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides of the AP Well ventilated (especially if it is in a closet) Operating temperature: 0~40 (32~104) Operating Humidity: 10%~90%RH, Non-condensing

Connecting the Device

Figure 2-3 is an example of an infrastructure network incorporating the TL-WA601G. An Infrastructure network contains an access point or a wireless router. For a typical connection of the AP, please do the following: 1. 2. 3. You will need broadband Internet access (a Cable or DSL-subscriber line into your home or office). Consult with your Cable or DSL provider for proper installation of the modem. Connect the Cable or DSL modem to a Router. Quickly install the router. Locate an optimum location for the AP. The best place is usually near the center of the area in which your PC(s) will wirelessly connect. The place must accord with the Installation Environment Requirements. 4

TL-WA601G 4. 5. 6.

Adjust the direction of the antenna. Normally, upright is a good direction. Connect the Ethernet Broadband Router to the TL-WA601G AP. Power on the AP. If you are connecting a desktop PC or laptop to your network, install the TP-LINK Wireless Adapter on the PC.
Figure 2-3 The Example of Infrastructure Network Incorporating the TL-WA601G

Configure PC

After connecting the TL-WA601G AP into your network, you should configure it. The default IP address of the TL-WA601G 108Mbps Wireless Access Point is 192.168.1.1, and the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN. They can be changed as you desire, as an example we use the default values for description in this guide. Connect the local PCs to the LAN ports on the AP. There are then two means to configure the IP address for your PCs. 1. From the Start menu on your desktop, go to Settings, and then click on Network Connections.
Figure 2-4 2. In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties.
Figure 2-5 3. In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet Protocol (TCP/IP) under This connection uses the following items: by clicking on it once. Click on the Properties button. 6
Figure 2-6 4. Select Obtain an IP address automatically by clicking the radio-button. Click OK
Figure 2-7 Configure the IP address manually 1. Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP). Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows XP 7
TL-WA601G Operating System. 3.
Open a command prompt, From the Start menu on your desktop, select run tab, type cmd in the field, and type ping 192.168.1.1 on the screen that appears, and then press Enter.
If the result displayed is similar to that shown in Figure below, the connection between your PC and the Router has been established.
Figure 2-8 If the result displayed is similar to that shown in Figure below, it means that your PC has not connected to the Router.
Figure 2-9 Please check it following these steps: Note: If the connection between your PC and the Router is correct? The LEDs of LAN port which you link to on the devicer and LEDs on your PC's adapter should be lit. If the TCP/IP configuration for your PC is correct? If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1.

Chapter 3 Software Configuration
This User Guide recommends using the Quick Installation Guide for first-time installation, For advanced users, if you want to know more about this device and make use of its functions adequately, you need to read this chapter and configure advanced settings though the Web-based Utility.
With a Web-based (Internet Explorer or Netscape Navigator) utility, the TL-WA601G 108Mbps Wireless Access Point is easy to configure and manage. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a web browser. Connect to the AP by typing http://192.168.1.1 in the address field of web browser.
Figure 3-1 Login to the AP After a moment, a login window will appear similar to that shown in Figure 3-2. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 3-2 Login Windows Note: If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. After your successful login, you can configure and manage the AP. There are six main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. The six main menus are: Status, Network, Wireless, DHCP, Wireless Advanced Settings and System Tools. On the right of the web-based utility, there are the detailed explanations and instructions for the corresponding page. To apply any settings you have altered on the page, please click the Save button. 9
There are the detailed explanations for each web page's key functions below.

Status

The Status page displays the AP's current status and configuration. All information is read-only. Network This field displays the current settings or information for the Network, including the MAC address, IP address and Subnet Mask. Wireless This field displays basic information or status for wireless function, including Operating Mode, SSID, Channel, Mode, MAC Address and IP Address. Traffic Statistics This field displays the AP's traffic statistics. System Up Time The time of the AP running from it's powered on or reset.

Enable WDS - The AP client can connect to AP with WDS enabled or disabled. If WDS is enabled, all traffic from wired networks will be forwarded in the format of WDS frames consist of four address fields. If WDS is disabled, three address frames are used. If your AP supports WDS well, please select the option. SSID - Enter the SSID of AP that you want to access. If you select the radio before SSID, the AP client will connect to AP according SSID. MAC of AP - Enter the MAC address of AP that you want to access. If you select the radio before MAC of AP, the AP client will connect to AP according MAC address.
Repeater - A wireless repeater is an AP with its own BSSID that relays data to a root AP, to which it is associated. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Please input the MAC address of root AP in the field of MAC of AP.
Universal Repeater - Without WDS, more APs can be communicated with in this mode.
Note: If the available AP cant support with WDS, you may select Client mode without WDS or Universal Repeater mode to associate with the AP. Here is an example of how to configure wireless repeater. Please do the following: 1. Configure the Operating Mode of the TL-WA601G Access Points. 13
Configure AP1 on LAN Segment 1 in Access Point mode. Configure AP2 in Repeater mode with the MAC address of its root AP (AP1). Configure AP3 in Repeater mode with the MAC address of its root AP (AP2).
Figure 3-7 Wireless repeating
Verify the wireless security parameters for all access points, if any. Verify connectivity across the LANs. A computer on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three WLAN segments. Note:
You can extend this repeating by adding up to 2 additional TL-WA601Gs configured in repeater mode. However, since Repeater configurations communicate in half-duplex mode, the bandwidth decreases as you add Repeaters to the network. Also, you can extend the range of the wireless network with wireless antenna accessories. Bridge (Point to Point) - This mode bridges the AP and another AP also in bridge mode to connect two wired LANs. Please input the MAC address of the other AP in the field of MAC of AP. Here is an example of how to configure Point-to-Point Bridge. Please do the following:

Figure 3-8 Point to Point Bridge 1. 2. Configure the TL-WA601G (AP1) on LAN Segment 1 in Point-to-Point Bridge mode. Configure the TL-WA601G (AP2) on LAN Segment 2 in Point-to-Point Bridge mode. AP1 must have AP2s MAC address in its MAC Address field and AP2 must have AP1s MAC address in its MAC Address field. Configure and verify the following parameters for both access points: 14
Both use the same Channel, and security settings if security is in use. Verify connectivity across the LAN 1 and LAN 2. A computer on either LAN segment should be able to connect to the Internet or share files and printers of any other PCs or servers connected to LAN Segment 1 or LAN Segment 2.
Bridge (Point to Multi-Point) - This mode bridges the AP and up to 4 APs also in bridge mode to connect two or more wired LANs. Please input the MAC address of other APs in the field of MAC of AP1 to MAC of AP4. Here is an example of how to configure multi-point bridging. Please do the following:
Figure 3-9 Point to Multi-point Bridge 1. Configure the Operating Mode of the TL-WA601G Access Points.
Because it is in the central location, configure TL-WA601G (AP1) on LAN Segment 1 in Point-to-Multi-Point Bridge mode. The MAC addresses of AP2 and AP3 are required in AP1. Configure TL-WA601G (AP2) on LAN Segment 2 in Point-to-Point Bridge mode with the MAC Address of AP1. Configure the TL-WA601G (AP3) on LAN 3 in Point-to-Point Bridge mode with the MAC Address of AP1.
Verify the following parameters for all access points.
All TL-WA601G Access Points use the same Channel, and security settings if any. All Point-to-Point APs must have AP1s MAC address in its AP MAC address field, and AP1 must have all All Point-to-Point APs MAC addresses.
Verify connectivity across the LANs. A computer on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three LAN segments.
Wireless stations will not be able to connect to the TL-WA601G Access Points in the illustration above. If you require wireless stations to access any lan segment, you can add TL-WA601G Access Points configured in Wireless Access Point mode to any LAN 15

TL-WA601G segment. Note:

You can extend this multi-point bridging by adding additional TL-WA601Gs configured in Point-to-Point mode for each additional LAN segment. Furthermore, you can extend the range of the wireless network with wireless antenna accessories.

3.4.2 Site Survey

After selecting a mode and pressing button Survey, you can view all of APs around you.
Figure 3-10 Site Survey SSID - The SSID of the AP. BSSID - The BSSID of the AP, usually also the MAC address of the AP. Signal - The signal received from the AP. Channel - The channel the AP works in. Security - The AP communicates in privacy. Choose - Choose one AP from list to connect to. Press one of Connect in list to select an AP to connect to. Then the basic settings will show again. You can save settings and reboot to take effective. Note: If wireless is disabled, surveying cant work. And if Access Point mode is selected, there is no reason and no choice to connect to another AP.

3.4.3 Security Settings

You can select one of the following security options:
Figure 3-11 Wireless Securities Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the AP without encryption. It is recommended strongly that you choose one of following options to enable security. WEP - Select 802.11 WEP security.
Type - You can select one of following types: 1) Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station's capability and request. 2) Shared Key - Select 802.11 Shared Key authentication. 3) Open System - Select 802.11 Open System authentication.
WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. WEP Key settings - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for 17
encryption. "Disabled" means this WEP key entry is invalid. 1) 2) 3) For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters. For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters.
Note: If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. WPA/WPA2 - Select WPA/WPA2 based on Radius Server.

2. 3. 4.

To add additional entries, repeat steps 1-6. Note: When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled. To modify or delete an existing entry: 1. 2. Click the Edit or Delete button in the Modify column in the MAC Address Filtering Table. Enter the value as desired in the Add or Modify Wireless MAC Address Filtering entry page, and click the Save button.
You can click the Enable All button to make all the entries effective, click the Disable All button to make all the entries ineffective, click the Delete All button to delete all the entries. Click the Next button to go to the next page and click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be able to access the AP, the wireless station B with MAC address 00-0A-EB- 00-07-5F not be able to access the AP, 20
and the wireless station C with MAC address 00-0A-EB-00-07-8A be able to access the AP when its WEP key is 2F34D20BE2E54B326C5476586A, while all other wireless stations cannot access the AP, you should configure the Wireless MAC Address Filtering list following these steps: 1. Click the Enable button to enable this function. 2. Select the radio button: Deny the stations not specified by any enabled entries in the list to access for Filtering Rules. 3. Delete all or disable all entries if there exist any entries already. 4. Click the Add New. button and enter the MAC address 00-0A-EB-00-07-BE in the MAC Address field, enter wireless station A in the Description field, select Allow in the Privilege pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return button. 5. Click the Add New. button and enter the MAC address 00-0A-EB-00-07-5F in the MAC Address field, enter wireless station B in the Description field, select Deny in the Privilege pull-down list and select Enabled in the Status pull-down list. Click the Save and the Return button. 6. Click the Add New. button and enter the MAC address 00-0A-EB-00-07-8A in the MAC Address field, enter wireless station C in the Description field, select 128-bit in the Privilege pull-down list, enter 2F34D20BE2E54B326C5476586A in the WEP Key field and select Enabled in the Status pull-down list. Click the Save and the Return button. The filtering rules that configured should be similar to the following list: Note: If you select the radio button Allow the stations not specified by any enabled entries in the list to access for Filtering Rules, the wireless station B will still not be able to access the AP, however, other wireless stations that are not in the list will be able to access the AP. If you enable the function and select the Deny the stations not specified by any enabled entries in the list to access for Filtering Rules, and there are not any enable entries in the list, thus, no wireless stations can access the AP.

3.4.5 Wireless Statistics
This page shows MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station.
Figure 3-14 The AP attached wireless stations MAC Address - The connected wireless station's MAC address Current Status - The connected wireless station's running status, one of STA-AUTH / 21
STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected Received Packets - packets received by the station Sent Packets - packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. Note: This page will be refreshed automatically every 5 seconds.
Figure 3-15 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 3-15): DHCP Settings, DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.

3.5.1 DHCP Settings

The System can be set up as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN. The DHCP Server can be configured on the page (shown in Figure 3-16):
Figure 3-16 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must manually configure the computer. Start IP Address - This field specifies the first of the addresses in the IP address pool. 192.168.1.100 is the default start address. End IP Address - This field specifies the last of the addresses in the IP address pool. 192.168.1.199 is the default end address. Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the system with their current dynamic IP Address. Enter the amount of time, in minutes, the user will be "leased" this dynamic IP Address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. Default Gateway - (Optional.) Suggest to input the IP address of the LAN port of the AP, default value is 192.168.1.1 Default Domain - (Optional.) Input the domain name of your network. Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your ISP. Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides two DNS servers. Note: To use the DHCP server function of the AP, you must configure all computers on the LAN as "Obtain an IP Address automatically" mode. This function will take effect until the AP reboots.

3.5.2 DHCP Clients List

This page shows Client Name, MAC Address, Assigned IP and Lease Time for each DHCP Client attached to the AP (Figure 3-17):
Figure 3-17 DHCP Clients List Index - The index of the DHCP Client Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the AP has allocated to the DHCP client. Lease Time - The time of the DHCP client leased. Before the time is up, DHCP client will request to renew the lease automatically. You cannot change any of the values on this page. To update this page and to show the current attached devices, click on the Refresh button.
3.5.3 Address Reservation
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to servers that require permanent IP settings. This page is used for address reservation (shown in Figure 3-18).
Figure 3-18 Address Reservation MAC Address - The MAC address of the PC of which you want to reserve IP address. Assigned IP Address - The IP address of the AP reserved. To Reserve IP addresses: 1. 2. Enter the MAC address (The format for the MAC Address is XX-XX-XX-XX-XX-XX.) and IP address in dotted-decimal notation of the computer you wish to add. Click the Save button when finished.
To modify A Reserved IP address: 1. 2. Select the reserved address entry as you desire, and modify it. If you wish to delete the entry, make all of the entry fields blank. Click the Save button.
To delete all Reserved IP addresses: Click the Clear All button. Click the Save button. Click the Next button to go to the next page and Click the Previous button to return the previous page. Note: The function won't take effect until the AP reboots.
Wireless Advanced Settings
You can configure wireless advanced settings on this page.
Figure 3-19 AP Wireless Advanced Settings Disable short preamble - Disable short preamble and use long preamble only. 802.11b mode supports only long preamble and this parameter will be ignored. RTS threshold - RTS/CTS Threshold, the packet size that is used to determine if RTS/CTS should be sent. Fragmentation threshold - The maximum packet size used for fragmentation. Beacon Interval - The interval time between two successive beacons.

System Tools

Figure 3-20 The System Tools menu There are five submenus under the System Tools menu (shown in Figure 3-20): Firmware, Factory Defaults, Reboot, Password, and Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.

3.7.5 Log

This page (shown in Figure 3-25) allows you to query the Logs of the AP.
Figure 3-25 System Log The AP can keep logs of all traffic. You can query the logs to find what happened to the AP. 29
TL-WA601G Click the Refresh button to refresh the logs. Click the Clear ALL button to clear all the logs.

Appendix A:

Glossary
108M Super G WLAN Transmission Technology - 108M Super G WLAN Transmission Technology employs multiple performance-enhancing techniques including packet bursting, fast frames, data compression, and dynamic turbo mode that combine to improve the throughput and range of wireless networking products. Users can experience link rates of up to 108Mbps, twice the industry-standard maximum data link rate of 54Mbps, while preserving full compatibility with traditional 802.11g or 802.11b networks. 108M Super G products offer the highest throughput performance available on the market today. In dynamic 108M mode, the device can attach 802.11b, 802.11g and 108Mbps Super G devices at the same time in an integrated environment. 2x to 3x eXtended RangeTM WLAN Transmission Technology - The WLAN device with 2x to 3x eXtended RangeTM WLAN transmission technology make its sensitivity up to 105 dBm, which gives users the ability to have robust, longer-range wireless connections. With this range-enhancing technology, a 2x to 3x eXtended RangeTM based client and access point can maintain a connection at as much as three times the transmission distance of traditional 802.11b and 802.11g products, for a coverage area that is up to nine times greater. A traditional 802.11b and 802.11g product transmission distance is about 300m, A 2x to 3x eXtended RangeTM based client and access point can maintain a connection transmission distance may be up to 830m. 802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. 802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. Access Point (AP) - A wireless LAN transceiver or "base station" that can connect a wired LAN to one or many wireless devices. Access points can also bridge to each other. DNS (Domain Name System) An Internet Service that translates the names of websites into IP addresses. Domain Name - A descriptive name for an address or group of addresses on the Internet. DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from operating or communicating. DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing traditional phone lines. ISP (Internet Service Provider) - A company that provides access to the Internet. MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted. SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key 31

identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices. WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area. WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that improves on the authentication and encryption features of WEP (Wired Equivalent Privacy). In fact, WPA was developed by the networking industry in response to the shortcomings of WEP. One of the key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP addresses the encryption weaknesses of WEP. Another key component of WPA is built-in authentication that WEP does not offer. With this feature, WPA provides roughly comparable security to VPN tunneling with WEP, with the benefit of easier administration and use. This is similar to 802.1x support and requires a RADIUS server in order to implement. The Wi-Fi Alliance will call this, WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key or WPA-PSK for short - this provides an authentication alternative to an expensive RADIUS server. WPA-PSK is a simplified but still powerful form of WPA most suitable for home Wi-Fi networking. To use WPA-PSK, a person sets a static key or "passphrase" as with WEP. But, using TKIP, WPA-PSK automatically changes the keys at a preset time interval, making it much more difficult for hackers to find and exploit them. The Wi-Fi Alliance will call this, WPA-Personal.
Appendix B: Specifications
General Standards and Protocols Safety & Emission Ports IEEE 802.3, 802.3u, 802.11b and 802.11g, TCP/IP, DHCP FCCCE One 10/100M Auto-Negotiation LAN RJ45 port supporting Auto MDI/MDIX 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) Cabling Type EIA/TIA-STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-STP (maximum 100m) Power Supply LEDs 9V~ 0.8A POWER, SYSTEM, LAN, WLAN Wireless Wireless Data Rates WEP Wireless Certification 108/54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps 64/128/152 bits Wi-Fi WPA Physical and Environment Working Temperature Working Humidity Storage Temperature Storage Humidity Dimensions (L x W x H) 0~40 (32~104) 10% - 90% RH, Non-condensing -40~70(-40~158) 5% - 90% RH, Non-condensing 6.24.31.3 in. (15811032 mm) (without antenna)

Appendix C: FAQ

1. No lights are lit on the access point. It takes a few seconds for the power indicator to light up. Wait a minute and check the power light status on the access point if the access point has no power. 1) 2) Make sure the power cord is connected to the access point. Make sure the power adapter is connected to a functioning power outlet. If it is in a power strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify that it is not a switched outlet. Make sure you are using the correct TP-LINK power adapter supplied with your access point.
The LAN light is not lit.
There is a hardware connection problem. Check these items: 1) Make sure the cable connectors are securely plugged in at the access point and the network device (hub, switch, or router). Make sure the connected device is turned on. Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the network device has Auto Uplink (MDI/MDIX) ports, you can use either a crossover cable or a normal patch cable.
I cannot access the AP with a wireless capable computer.
There is a configuration problem. Check these items:
1) You may not have restarted the computer with the wireless adapter to have TCP/IP changes take effect. Restart the computer. The computer with the wireless adapter may not have the correct TCP/IP settings to communicate with the network. Restart the computer and check that TCP/IP is set up properly for that network. The usual setting for Windows the Network Properties is set to Obtain an IP address automatically. The access points default values may not work with your network. Check the access point default configuration against the configuration of other devices in your network.

Appendix D:

http://www.tp-link.com

Contact Information

For help with the installation or operation of TP-LINK Product, please visit our website.