20 Ringer Options (10 Tones/10 Melodies) Personalized Ring by Party 10 Speed Dial Numbers Last 3 Number Redial Copy Phonebook Entries to Another Handset English, Spanish and French Menu Displays Call Transfer Conferencing Intercom
Answering System Features Digital Tapeless Recording Up to 12 Minutes of Recording Time Personal or Pre-recorded Outgoing Messages English, Spanish, or French Voice Prompts for
Menu Setup Day and Time Announcement
Remote Message Retrieval Toll Saver Conversation Recording Voice Memo Message Alert Records Up to 59 messages

Parts of the Handset

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Handset Antenna Headset Jack Cover Beltclip Hole Speakerphone Speaker and Ringer Handset Battery Compartment New Message LED Handset Earpiece LCD Display [menu/clear] key [redial/pause] key ] key (phonebook)
11. [ / flash] key (talk/flash) 12. [ 13. [*/tone/<] key 14. [xfer/intercom] key 15. [select/ 16. [ 18. [

] key (select/messages)

] key (up) ] key (caller ID)

17. [ ] key (end call)

] key (down) 19. [ 20. [#/>] key (pound)
21. [ ] key (speaker) 22. Handset Microphone 23. Handset Charging Contacts
Parts of the Answering System Base (DCT758)
1. Base charging contacts 2. charge LED 3. Base speaker 4. [greet] key (record greeting) 5. [set] key 6. [menu/clock] key 7. [ ] key (delete)
8. [ /select] key (repeat/select) 9. Message counter LED 10. [on/off] key (answering system on/off) 11. [ /select] key (skip/select) 12. [ ] key (play/stop) 13. Base antenna
/ ] key (volume 14 [ up/down for speaker/ringer) 15. in use LED 16. [find hs] key (find handset) 17. [ dnd] key (do not disturb) 18. [int'com] key (intercom) 8
19. 20. 21. 22. 23. 24. 25. 26.
[hold] key [mute] key [memo/call rec] key [speaker] key [ flash] key Base microphone TEL LINE phone jack DC IN 9V power jack
Parts of the Answering System/Dual-keypad Base (DCT7585/DCT7085)
1. Base charging contacts 2. charge LED 3. Base speaker 4. [greet] key (record greeting) 5. [set] key 6. [menu/clock] key 7. [ ] key (delete) 8. [ /select] key (repeat/select)
9. Message counter LED 10. [on/off] key (answering system on/off) 11. [ /select] key (skip/select) 12. [ ] key (play/stop) 13. Base antenna / ] key (volume 14 [ up/down for speaker/ringer)
15. in use LED 16. [memo/call rec] key 17. [hold/int'com/xfer] key (hold/intercom/ transfer) 18. [mute/find hs] key (mute/ find handset) 19. [ dnd] key (do not disturb)
20. 21. 22. 23. 26. 27. 28.
[*/tone] key [#] key (pound) [speaker] key [ flash] key [ redial/pause] key [memory] key Base microphone TEL LINE phone jack DC IN 9V power jack

Using the Interface

Reading the Display
The handset display uses icons to tell you the status of your phone. The table below lists the icons and what they mean.

Status

Standby/Talk Standby Talk Talk Talk Talk Talk

Description

The battery icon indicates the handset battery status: full, medium, low, and empty. The ringer off icon indicates that the ringer is turned off. The mute icon appears while the handset microphone is muted. The call record icon appears while recording a conversation. The boost icon appears when the Clarity Boost feature is activated. The speaker icon appears when the handset speaker phone is in use. The privacy icon appears when the Privacy Mode is turned on.

The Standby Screen

When the phone is in standby, the handset display shows the following items: Ringer status / Day and time / Battery status Handset banner Number of new Caller ID messages received
Using the Four-way Function Key
Your handset has a four-way function key that allows you to move the cursor or pointer on the display and access the most commonly used features at the touch of a button. By moving this key to the left, you open the phonebook. Move the key to the right to access Caller ID information. To use this four-way key, place your thumb over the key on the handset and move to the four positions to get the feel of how it moves and operates.

Using the Handset Menus

To open the menu, press [menu/clear]. Select the option you want by pressing the four-way function key. This will move the cursor; the option currently selected has a triangle beside it. Activate the selected option by pressing [select/ ]. To exit the menu and return to standby, press [ ]. If you do not press a key within 30 seconds, the phone will time out and exit the menu. When setting the day and time, the time-out period is extended to two minutes.
Entering Text from Your Handset
You can use the number keypad on your phone to enter text by referring to the letters printed on each number key. When you press the number key in a text entry field, the phone displays the first letter printed on the number key. Press the number key twice to display the second letter and three times to display the third. Capital letters are displayed first, then lower case letters, then the number on the key. If two letters in a row use the same number key, enter the first letter, then use [#/>] to move the cursor to the next position to enter the second letter. For example, to enter the word "Movies": 1. Press [6] once to enter M. 2. Use [#/>] to move the cursor to the right. 3. Press [6] six times to enter o. 4. Press [8] six times to enter v. 5. Press [4] six times to enter i. 6. Press [3] five times to enter e. 7. Press [7] eight times to enter s. 8. Press [select/ text entry.

] to end your

If you make a mistake while entering a name, use [*/tone/<] or [#/>] to move the cursor to the incorrect character. Press [menu/clear] to erase the wrong character, and then enter the correct character. To delete all characters, press and hold [menu/clear].

Installing the Phone

Choosing the Best Location
When choosing a location for your new phone, here are some important guidelines you should consider:
The location should be close to both a phone jack and a power outlet that is not controlled by a wall switch. The base and handset should be kept away from sources of electrical noise such as motors, microwave ovens, and fluorescent lighting. Don't place the base in direct sunlight or subject it to high temperatures. The battery may not charge properly. For better reception, place the base as high as possible. The base should be placed in an open area for optimum range and reception. If your home has specially wired alarm equipment connected to a phone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

Wall Mounting the Base

This phone can be mounted on any standard wall plate. 1. Snap the wall mount adapter into the notches on the base top. 2. Plug the AC adapter into the DC IN 9V jack. CAUTION: To avoid risk of fire and shock, only use the Uniden AD-800 AC adapter. 3. Wrap the AC adapter cord inside the molded wiring channel as shown. 4. Plug the AC adapter into a standard 120V AC wall outlet. DO NOT use an AC outlet controlled by a wall switch.
5. Plug the telephone line cord into the TEL LINE jack. 6. Plug the telephone cord into the telephone jack. 7. Align the mounting slots on the base with the mounting posts on the wall. Then push in and down until the phone is firmly seated.

Installing the Battery

Follow the steps below to install the handset battery. 1. Press in on the handset battery case cover (use the finger indention for a better grip) and slide the cover downward to remove. 2. Place the battery pack in the battery compartment with the connectors on the battery and on the compartment aligned. 3. Place the battery case cover back on the handset and slide it upwards until it clicks into place. Note: Use only the Uniden BT-909 rechargeable battery pack supplied with your cordless telephone.

Registering DCX640 or DCX700 Handsets
1. On the base, press and hold [flash] until the CHARGE LED starts to blink. 2. On the handset, press and hold [#/] until you hear a beep. 3. While the handset is registering, HANDSET REGISTERING appears in the display. When the display shows REGISTRATION COMPLETE, the handset has been registered to the base. If REGISTRATION FAILED appears, please try these steps again.

Resetting Handsets

If you want to register the handset to a different base or replace a handset with another one, you must first clear the registration information from the base and the handset. 1. Press and hold [ ] and [#/>] for at least 5 seconds, until the SYSTEM RESET menu appears. 2. Select the DEREGISTER HS submenu. WHICH HANDSET? appears in the display. 3. Use [ ] and [ ] to select the handset ID you want to de-register, and then press [select/ DEREGISTER HS appears. 4. When the phone asks you to confirm, move the cursor to select YES, and then press [select/ hear a confirmation tone. ]. ]. You will
Note: The handset first clears it registration information from the base and then deletes the link to the base from its own memory. The handset will now display MODELS VARY! CHARGE HANDSET ON THE BASE FOR REGISTRATION OR REFER TO OWNERS MANUAL. If the handset cannot contact the base, it will display UNAVAILABLE. If this happens, see Resetting the Handset Without the Base on page 60. For instructions on registering the handset, see page 20.

Setting Up the Phonebook

Your handset can store up to 100 names and numbers in your phonebook. Your phone shares memory between your phonebook and Caller ID entries. Once you store 100 phonebook entries, Caller ID information will not be stored and will only display at time of new incoming call. When all the phonebook entries are full, you will hear a beep and MEMORY FULL appears. You cannot store any additional names and numbers unless you delete some of the existing ones. You can also use the phonebook entries or speed dial memory to store a group of numbers (up to 20 digits) that you may need to enter once your call connects. This is referred to as chain dialing.
Creating Phonebook Entries
To store names and numbers in your phonebook, please follow these steps: 1. When the phone is in standby mode, press [ ].
2. To create a new phonebook entry, move the cursor to select STORE ]. STORE/EDIT NAME appears. NEW, and press [select/ 3. Enter the name for this entry (STORE/EDIT NAME). Use the keypad to enter a name for this entry; the name can contain up to 16 characters. (See Entering Text from Your Handset on page 12 for instructions on entering text.) If you do not want to enter a name for this entry, your phone will store this entry ] when you are finished. as <NO NAME>. Press [select/

Programming Base Speed Dial Numbers (Dual Keypad Model Only)
The dual keypad base can store 10 speed dial numbers, [0] to [9]. Follow the steps below to store new speed dial numbers in the base. (Handset speed dial numbers are stored as part of a phonebook entry. See Creating Phonebook Entries on page 22 for information on programming handset speed dial numbers.) 1. With the phone in standby, press [memory]. 2. Use the number keypad to enter the phone number; the phone number can contain up to 20 digits. If you need the phone to pause between digits when its dialing (for example, to enter an extension or an access code),
press [redial/pause] to insert a two-second pause. You can also use more than one pause together if two seconds is not long enough. Each pause counts as one digit. 3. Press [memory] again, and then press the number key ([0] to [9]) where you want to store this phone number. You will hear a confirmation tone.
Deleting Base Speed Dial Numbers
1. With the phone in standby, press [memory] twice. 2. Press the number key ([0] to [9]) that contains the phone number you want to delete. You will hear a confirmation tone.

Customizing Your Phone

Changing the Handset Banner
Each handset will display a banner name once it is registered to the base. The default banner is Handset #1, Handset #2, etc. You can change the name your phone displays by changing the banner display. If you have more than one handset, the banner name identifies your handset during handset-to-handset functions like intercom and DirectLink communication. The name will be displayed on the LCD screen during Standby, Intercom, Intercom Hold, Room/Baby Monitor, and Copy Phonebook operations. The banner name will be displayed on the receiving handset as well. 1. Press [menu/clear]. 2. Select the HANDSET SETUP menu, and then the BANNER submenu. 3. Use the keypad to enter or edit the banner name. (See Entering Text from Your Handset on page 12 for detailed instructions on entering text.) 4. Press [select/ ]. You will hear a confirmation tone.
Selecting a Ring Tone (Handset Only)
You may choose from 10 melodies or 10 tones for your phone's primary ring tone. Each station can use a different ringer tone or melody. The available ring tones are listed below:

Melodies

Beethoven's Symphony #9 (BEETHOVEN9) For Elise (ELISE) We Wish You A Merry Christmas (MERRY- XMAS) Home Sweet Home (HM SWT HM) Lorri Song #6 (LORRI SONG) When Irish Eyes Are Smiling (IRISH EYES) Aura Lee (AURA LEE) Let Me Call You Sweet Heart (SWEETHEART) Star Spangled Banner (STAR SPNGL) Old MacDonald (OLD MACDLD) Beep Boop Tone Board Chip Chop Party Clap Reminder

Ringers

Flicker Clatter Soft Alert Wake Up Light Bug
1. Press [menu/clear]. Select the HANDSET SETUP menu, and then the RINGER TONES submenu. 2. Move the cursor to select a ring tone. As each ring tone is selected, you will hear a sample of the ring tone. 3. When you hear the tone you want to use, press [select/ hear a confirmation tone. ]. You will

Using Call Waiting Deluxe
Your handset gives you new options for Call Waiting Deluxe. At the touch of a button, you can place the caller on hold, send them to your voice mail service, or conference them into your current call. You must subscribe to both Call Waiting and Call Waiting Deluxe to use these features. Check with your telephone provider for details. 1. When you receive a call waiting call, press [menu/clear]. 2. Move the cursor to select CW Deluxe, and then press [select/ ].
3. Move the cursor or use the number keypad ([1] through [7]) to select an option:
Ask to Hold A prerecorded message states that user will be available shortly, and the call is place on hold. Tell Busy - A prerecorded message tells the caller you are busy, and the waiting call is disconnected. Forward Call - The caller is sent to your voice mail box, if available. Answer/Drop 1 - Disconnects the first call, and connects to the new caller.
Conference - Starts a conference call with your first and second callers. Drop First/Drop Last - During a conference call, allows you to choose to drop the first or last caller. ]. A confirmation screen will appear, and the phone returns to the call.

4. Press [select/

Redialing a Number
You can quickly redial the last 3 numbers dialed on each handset or the last number dialed on the dual-keypad base.
From the dual-keypad base
1. Press [speaker]. 2. Then press [redial/pause].

From the handset

1. With the phone in standby, press [redial/pause] to open the redial list. 2 Use [redial/pause] or [ ] and [ ] to scroll through the redial list.
3. When you find the number you want to dial, press [ / flash] or [
Note: You can also redial the last number dialed on the handset by pressing [ / flash] or [ ], and then [redial/pause].

Deleting a Redial Record

If you want to delete a phone number from the handset's redial list, follow the steps below: 1. With the phone in standby, press [redial/pause]. 2. Use [ ] and [ ] to scroll through the redial list.
3. When you find the redial number you want to delete, press [menu/clear]. 4. Select YES, and press [select/ ] or [menu/clear]. The redial number is deleted.
Adjusting the Ringer, Earpiece and Speaker Volume
Adjusting the Ringer Volume
You can choose from three ringer volume settings on the handset (off, low, and high) and four options (off, low, ] or [ ] to adjust the ringer volume. medium, and high) on the base. With the phone in standby, use [
Adjusting the Earpiece Volume

You can use the intercom to talk to another station without using the phone line.
Making an Intercom Page From the base
1. With the phone in standby, press [int'com] ([hold/ int'com/xfer] on the dual-keypad base). All other stations will be paged. (On the dual-keypad base, press [1] through [4] to select the handset you want to talk with or press [*/tone] to page all other stations.) 2. To cancel the intercom page, press [int'com] ([hold/int'com/xfer] on the dual-keypad base).
1. With the phone in standby, press [xfer/intercom]. ] or [ ] to select the station you 2. Use [ want to talk with, then press [select/ ]. Select ALL to page all other stations. 3. To cancel the intercom page, press [ ].
Note: Intercom paging will be canceled if any of the following things occur: --You receive an outside call or an intercom page while selecting the other handset. --You do not select a handset within 30 seconds. --The party does not answer the page within one minute. --The party is busy. --The party is out of range (UNAVAILABLE appears in the display).
Answering an Intercom Page
When the intercom page tone sounds, the display will show the ID of the station that is paging. 1. From the handset, press [ / flash] or [xfer/intercom]. If AutoTalk is on, the handset will automatically answer the page when you remove the handset from the cradle. 2. From the base, press [int'com] ([hold/int'com/xfer] on the dual-keypad base) or [speaker]. 3. To hang up an intercom page from the handset, press [ ]. To hang up an intercom page from the base, press [int'com] ([hold/int'com/xfer] on the dual-keypad base).

Room/Baby Monitor

This feature allows you to monitor sounds in another room. Place a station in the room you wish to monitor; it will function as a microphone. Any handset can be set to function as a remote speaker, allowing you to monitor sounds in the room. 1. Press [menu/clear] and enter the ROOM MONITOR menu. TO ROOM MONITOR appears in the display. ] or [ 2. Use [ monitor. ] to select the station you want to

Handset operation

You can use your handset to operate your answering system from anywhere in your home. When the phone is in ] on the handset to access the answering system. REMOTE ANSWERING MACHINE standby, press [select/ OPERATION appears on the handset display, and the system announces the number of new and old messages. Keep the following things in mind when you use your handset to access your answering system:
You can enter a command at any time during announcements. After the first announcement, you have 30 seconds to enter your first command before the system returns to standby. If you receive a call, the remote operation is cancelled. If another station makes a call, the remote operation is cancelled. During the remote operation - - appears on the base.

Selecting the Language

You can select the language (English, French, and Spanish) of your answering system announcements. The default system language is English.
1. Press [menu/clock] six times. 2. The current setting ("E" English, "F" French, or "S" Spanish) appears on the base, and it is announced ("English" English, "Franais" French, or "Espaol" Spanish). 3. Press [ /select] or [ /select] to select the language.
1. Press [menu/clear]. Select ANSW. SETUP, and then the LANGUAGE submenu. 2. Move the cursor to choose ENGLISH, FRANAIS (French), or ESPAOL (Spanish). 3. Press [select/ ]. You will hear a confirmation tone.
4. Press [set]. A confirmation tone sounds, and the system announces the new setting in the selected language.
Setting the Number of Rings
The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS) setting, the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the second ring to avoid long distance billing charges.
1. Press [menu/clock] three times. The base displays the current number of rings (2, 4, 6, or TS for toll saver) and announces the setting. 2. Press [ /select] or [ ring time appears. /select] until the desired
1. Press [menu/clear]. Select the ANSW. SETUP menu, and then the RING TIME submenu. 2. Move the cursor to select a ring time (TOLL SAVER, 2 TIMES, 4 TIMES, or 6 TIMES). 3. Press [select/ ]. You will hear a confirmation tone.
3. Press [set]. A confirmation tone sounds, and the system announces the new ring time.
Setting the Day & Time
If you do not set the clock on your answering system, your messages may not have the correct time and day stamp. You can set the day and time from the handset or the base.

3. Press [set]. A confirmation tone sounds, and the system announces the new setting.
Setting a Security Code or Personal Identification Number (PIN)
To play your messages from a remote location, you will need to enter a two-digit security code or Personal Identification Number (PIN). The default security code is 80.
1. Press [menu/cock] twice. The current security code appears on the base and it is announced. 2. Press [ /select] or [ /select] until the desired number appears. Press and hold [ /select] or [ /select] to quickly scroll through the numbers on the display. 3. Press [set] to select the security code. A confirmation tone sounds; the system announces the new security code.
1. Press [menu/clear]. Select the ANSW. SETUP menu, and then the SECURITY CODE submenu. 2. Use the number keypad ([0] through [9]) to enter a two-digit security code (01-99). ]. You will hear a 3. Press [select/ confirmation tone.
Using the Answering System
Turning Your Answering System On and Off
1. With the phone in standby, press [on/off]. 2. The system announces "Answering System is on" and plays the current greeting. 3. The message counter displays the number of messages stored in memory. If the counter flashes, then you have new messages waiting. 1. With the phone in standby, press [on/off].
]. 1. With the phone in standby, press [select/ REMOTE ANSWERING MACHINE OPERATION appears on the display, and the answering system announces the number of new and old messages. 2. Press [6] at any time during the announcement. 3. The system announces "Answering System is on" and plays the current greeting message.

Turning On

Turning Off
2. The phone announces "Answering System is off." 3. The message counter LED is no longer illuminated.
1. With the phone in standby, press [select/ ]. REMOTE ANSWERING MACHINE OPERATION appears on the display, and the answering system announces the number of new and old messages. 2. Press [9] at any time during the announcement. The system announces "Answering System is off."

Reviewing Messages

The base message counter displays the number of messages stored in memory. When you have new messages, the message counter and the new message LED on the handset flash. The answering system plays your new messages first. After you listen to all of your new messages, you can then play your old messages. You can review your messages from the base or from the handset:

Stopping a memo

2. You hear a confirmation tone, and the system returns to standby.
Turning Off the Message Alert Tone
When all new messages are played back, the message alert tone will automatically deactivate. The tone will not deactivate until all new messages are played back. To quickly turn off the tone, press any key on the base.
Operating the Answering System While You Are Away from Home
You can access your answering system while you are away from home to check, play, and delete messages, or even record a new greeting message or turn your answering system on and off.
To operate from a remote location, use any touch-tone telephone, and follow these steps: 1. Call your telephone number and wait for the system to answer. If the answering system is off, it will answer after about 10 rings and sounds a series of beeps. 2. During the greeting or the beeps (if answering system is off), press 0 and enter your security code/PIN within two seconds (see Setting a Security Code or Personal Identification Number (PIN) on page 51). 3. The answering system announces the current time and the number of messages stored in memory. You hear "To play incoming messages, press zero-two. For help, press one-zero" followed by a beep. 4. Enter a remote command from the chart below. You have 15 seconds to enter the first command; after the first command, you have two seconds to enter each command.

Command

[0] then [1] [0] then [2] [0] then [3] [0] then [4] [0] then [5] *

Function

Repeat a message* Play incoming messages Skip a message Delete a message Stop operation
[0] then [6] [0] then [7] [0] then [8] [0] then [9] [1] then [0]
Answering system on Memo record start/stop Greeting message record start/stop Answering system off Help
If you press [0] then [1] in the first four seconds of a message, the system skips to the previous message. If you press [0] then [1] after the first four seconds of a message, the system repeats the current message.
5. When you finish, you will hear intermittent beeps indicating that the system is in the command waiting mode. Enter another command from the chart within two seconds. 6. Hang up to exit the system. The answering system automatically returns to its normal standby setting.

Maintenance

Specifications
Operating Temperature 0 C to +50 C (+32 F to +122 F) Part Number AC Adapter Input Voltage Output Voltage Part Number Capacity Base: AD-800 Charging cradle: AD-0005 Base: 120V AC, 60 Hz Charging cradle: 120V AC, 60 Hz Base: 9V D @ 350 mA Charging cradle: 9V D @ 210 mA BT-909 3.6V DC @ 600 mA

Battery

Power Failures
During a power failure, you will not be able to make or receive calls with the phone. To avoid damage from an electrical spike when the power comes back on, we recommend you unplug your phone during power outages.

Uniden America Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
Rechargeable Nickel-Metal-Hydride Battery Warning
This equipment contains a rechargeable Nickel-MetalHydride battery. The rechargeable batteries contained in this equipment may explode if disposed of in a fire. Nickel is a chemical known to state of California to cause cancer. Do not short-circuit the battery. Do not charge the rechargeable battery used in this equipment in any charger other than the one designed to charge this battery as specified in the owner's manual. Using another charger may damage the battery or cause the battery to explode.
1. Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local authorities for possible battery disposal instructions. 5. Do not disassemble any component of this product.
Rechargeable Batteries Must Be Recycled or Disposed of Properly
SAVE THESE INSTRUCTIONS CAUTION!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Do not open or mutilate the battery, and disconnect the battery before shipping this product.
The FCC Wants You To Know
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. An applicable Universal Service Order Codes (USOC) certification for the jacks used in this equipment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the telephone provider. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isnt practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is

ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This warranty is void outside the United States of America and Canada. PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions in the owners manual you are certain that the Product is defective, pack the Product carefully (preferably in its original packaging). Disconnect the battery from the Product and separately secure the battery in its own separate packaging within the shipping carton. The Product should include all parts and accessories originally packaged with the Product. Include evidence of original purchase and a note describing the defect that has caused you to return it. The Product should be shipped freight prepaid, by traceable means, to warrantor at: Uniden America Service 4700 Amon Carter Blvd. Fort Worth, TX 76155
Accessibility.. 4 Answering calls.. 30 Answering system. 44 Using the handset.. 45 When away from home. 55 Any key answer.. 29 AutoTalk.. 29 Baby monitor. 42 Banner. 27 Base Installing.. 13 Parts of the base. 8 Parts of the dual keypad base.. 9 Wall mounting. 13 Battery Installing.. 14 Low battery alert. 58 Replacement and handling. 58 Talk and standby time. 57 Belt clip.. 16 Call recording.. 54 Call screening. 50, 53 Call waiting. 33 Call waiting deluxe. 18, 33 Caller ID.. 32 Caller ID on call waiting.18 Deleting Caller ID records..33 Making calls from.32 Clarity booster.10, 36 Conferencing..37 Day and time.17, 47 Dial mode.16, 43 DirectLink..40 Making a call.40 Do not disturb.38 FCC statements..66 Finding a handset.36 Greetings Deleting..49 Recording..48 Selecting..48 Handset Accessing the answering system..45 Accessory handsets.19 Banner..27 Choosing a ringer.28 Copying phonebook entries..25 Displays and icons..10 Entering text..Finding..36 Parts of the handset.7 Registering.20 Resetting.21, 59 Standby screen..11 Hanging up.30 Headset..43 Hold.36 Installation.13 Intercom..41 Key touch tone.18 Maintenance..57 Making calls..30 Using Caller ID..32 Using redial.34 Using speed dial.31 Using the phonebook.31 Message alert.50, 55 Mute Microphone.39 Ringer..38 Out of range..61 Personal identification number (PIN)..51 Personal ring..18 Phonebook..22 Copying entries..25

Need a part?

If you need special assistance due to a disability or have questions Help for our customers with on the accessibility features of this product, please call 1-800-874-9314 (voice or TTY). special needs
May be covered under one or more of the following U.S. patents: 4,797,916 5,381,460 5,426,690 5,434,905 5,581,598 5,650,790 5,660,269 5,661,780 5,732,355 5,754,407 5,758,289 5,768,345 5,864,619 5,893,034 5,912,968 5,915,227 6,044,281 6,070,082 6,125,277 6,253,088 6,714,630 6,782,098 6,788,920 6,788,953 6,914,940 Other patents pending.
5,491,745 5,663,981 5,787,356 5,929,598 6,314,278 6,839,550
5,493,605 5,671,248 5,794,152 5,930,720 6,418,209 6,889,184
5,533,010 5,696,471 5,801,466 5,960,358 6,618,015 6,901,271
5,574,727 5,717,312 5,825,161 5,987,330 6,671,315 6,907,094