TVs Other electronics

Personal computers Wireless LAN equipment
Areas with a lot of background noise
In a centrally-located open area.
Direct sunlight Extreme temperatures

Dust Excessive moisture

Shock Vibration
Note: For maximum range: Keep both the base and handset antennas free of obstruction. When the handset is not in use, place the handset in an upright position. Metal and reinforced concrete may affect cordless telephone performance.

Installing the Battery

Use only the Uniden BT-446 rechargeable battery pack supplied with your cordless telephone. Locate the battery pack, battery cover and the handset. Line up the red and black wires on the battery pack connector with the sticker in the handsets battery compartment. Push the battery pack connector in firmly. (You should hear it click into place.) Gently tug on the battery wires to make sure the connection is secure. Installing the Phone

Battery pack

Battery cover
Place the cover over the battery compartment and slide it up into place. Handset
Connecting the AC adapter

To the base

To avoid risk of fire and shock, only use the Uniden PS-0009 AC adapter with the base. Connect the AC adapter to the DC IN 9V jack on the bottom of the base. Route the cord through the molded wiring channel. Connect the AC adapter to a standard 120V AC wall outlet.
Dont put any power cord where it people might trip over it or step on it. If a power cord becomes chafed or worn out, it can create a fire or electrical hazard.
To the charging cradle (for multi-handset packs only)
Use only the Uniden PS-0007 AC adapter with the charging cradle. Place the cord through the molded wiring channel. Connect the AC adapter to a standard 120V AC wall outlet.

Charging the Handset

Place the handset in the base cradle with the display facing forward.
If you have an accessory handset, place it in the charging cradle with the display facing forward.
Make sure that the charge LED illuminates when the handset is seated. What if the charge LED doesnt light up? Reseat the handset; make sure the contacts on the bottom of the handset are lined up with the contacts in the charging cradle. Check the AC adapter connection. Make sure you are not using an outlet thats controlled by a wall switch.

Make sure that the charge LED illuminates when the handset is seated.
Charge your handset at least 15 to 20 hours before plugging into the phone line.
Connecting to the Phone Line
Make sure that the battery pack is fully charged. Connect the telephone cord to a telephone wall jack. What if CHECK TEL LINE appears on the base or handset display? The telephone cord may not be connected correctly. Check the telephone cord connection.
Connect the telephone cord to the TEL LINE jack.
Do you have DSL or any high-speed Internet service delivered through your phone line? Try putting a DSL filter between the base and the wall jack. Without a filter, telephone-line-based Internet services can interfere with standard phones. Telephone cord Telephone wall jack

DSL filter

Testing the Connection
Pick up the handset from the base and press [ /flash]. You should hear a dial tone, and the display should show TALK. What if I cant hear a dial tone? Check the telephone cord connection on the base. What if the display doesnt show TALK? Check the battery pack connection in the handset. Make sure the battery pack is fully charged. Make sure the AC adapter cord is securely connected to the. DC IN 9V jack and a standard power outlet. Try resetting the handset (see page 54). Make a quick test call, and then press [ ] to hang up. What if there is a lot of static? Check the sources of interference described in Choosing the Best Location (see page 5): is the base near any of those? What if the call doesnt go through? Try changing the dialing mode (see the next section). Note: Make sure you can get a dial tone on any accessory handsets that were packaged with your phone. Installing the Phone

Changing the dial mode

Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most base networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you will need to change your phones dial mode. If you dont get a dial tone or cant connect to the telephone network, please follow the steps below to modify your phones settings: ) Press [menu/select]. 2) Select the GLOBAL SETUP menu, and then the DIAL MODE submenu. 3) Scroll [ ] to highlight PULSE. 4) Press [menu/select]. You will hear a confirmation tone. If you ever need to change the dial mode back to tone dialing, follow the same procedure, but select TONE in step 2.

(Bottom of the base)

Place the mounting slots over the pins on the wall plate.

Wall plate

Slide the base down to lock it into place. Installing the Phone
Removing the wall-mount bracket At the bottom of the base, lift up on the release latch between the two bottom tabs and push the bracket up.
(To AC outlet) Note: Mounting the phone directly on the wall Be sure the wall is capable of supporting the weight of the phone, and use the proper type of anchoring device for the wall material. Insert two #10 screws (minimum length of 1 3/8 inches, not supplied) into the wall, 3 15/16 inches apart. Leave the screw heads 1/8 inch away from the wall to allow room for mounting the phone. Align the mounting slots over the screws and slide the base down into place as shown above.

Release latch

Getting to Know Your New Phone

Features

5.8GHz FHSS expandable system Expands up to 10 handsets Integrated digital answering system Caller ID/Call Waiting Base keypad Advanced phonebook features: Store 70 phonebook entries on base & each handset Alphabetical search Personalized ring by party (on handset) Transfer single listing or entire phonebook Store 30 Caller ID numbers on base & each handset Speakerphone on base & handset 7 ringer options on handset (3 tones/4 melodies) Last 5 number redial Bilingual menu displays. (for US models: English and Spanish,. for Canadian models: English and French) Call transfer Conferencing Intercom
Answering system features
Getting to Know Your New Phone Digital tapeless recording Up to 14 minutes of recording time Call screening Personal or pre-recorded outgoing messages Bilingual voice prompts. (for US models: English and Spanish,. for Canadian models: English and French) Day and time announcement Remote message retrieval Toll saver Message alert Records up to 59 messages
Terminology Used in this Manual
Accessory Handsets Base Charging cradle CID CID/CW or CIDCW Global Settings Additional handsets that can register to the base, allowing you to add handsets without connecting another phone line. This base supports a total of ten cordless handsets; see page 12 for compatible handsets. The main part of the phone that connects to your phone line and lets you make and receive calls. A cradle that comes with an accessory handset and charges the handset battery pack. It connects to power but does not connect to a phone line. Caller ID is available from your telephone provider and is offered to users on a subscription basis. With this service, you will be able to see the incoming caller information such as name and phone number. Caller ID with Call Waiting is available by subscription from your telephone provider. With this service, you will be able to view incoming caller information while on a call with another user. Any settings that apply to all registered handsets and the base. These features are available by selecting GLOBAL SETUP in the handset or the base menu. Only one handset or the base can change global settings at a time, and you have to make sure the phone is not currently being used. The handset and the base are not in use. (It doesnt matter whether the handset is in the cradle: the [ /flash] or [ ] on the handset or [ ] on the base hasnt been pressed, and there is no dial tone.) Any registered handset or the base. A dial tone has been enabled, so you can dial and carry on a conversation with an outside party.

Standby Station Talk

Manual Conventions
This manual uses several different type styles to help you distinguish between different parts of the phone: Bold text with [ ] indicates a key or button on the phone ALL CAPITALS indicates text on the display, such as menu options, prompts, and confirmation messages lower case bold text indicates a status light on the phone ALL CAPITALS BOLD indicates a connection jack on the base or charging cradle

Parts of the Handset

new message LED

Earpiece

Headset jack cover Belt clip hole
Display (LCD) [clear/intcom] key (clear/intercom) [ ] key (phonebook/left) [ /flash] key (talk/flash) [ ] key (up) Speakerphone speaker and ringer
[menu/select] key [ ] key (caller ID/right)
[ ] key (end call) [ ] key (down) Battery compartment
Twelve-key dial pad [ Getting to Know Your New Phone /tone] key [#] key [ ] key (speaker)
[redial/pause] key [ /mute] key (messages/mute)
Microphone Charging contacts

Parts of the Base

Display (LCD) [clear/mute] key charge LED [menu/select] key [redial/pause] key [ / ] key (phonebook/repeat/left) [ ] key (up)

Charging contacts

[ / ] key (caller ID/skip/right) [ ] key (down) [ ] key and LED (play/stop)
[ answer on/off] key (answering system on/off) Microphone (on bottom) [ Speaker Getting to Know Your New Phone ] key (delete)
[int'com] key (intercom) [ /tone] key

[#] key [flash] key

] key and LED (speaker)

Using the Interface

Reading the Display

Handset In standby

Handset ID and banner Number of new Caller ID calls received

During a call

Call duration
Note: The handset does not display the day and time. Base Status of your In standby
Day of the week and time Number of new Caller ID calls received

Answer ON OFF

answering system
Status of your answering system

Message counter

The ringer off icon indicates that the ringer is turned off. The voice mail icon appears when you have messages waiting in your voice mailbox. The privacy icon appears when the Privacy Mode is turned on. The speaker icon appears when the speaker phone is in use. The mute icon appears while the microphone is muted. The battery icon indicates the handset battery status: full, medium, low, and empty.
Using the Four-way Function Key
Your handset and base have a four-way function key that allows you to move the cursor or pointer on the display and access the most commonly used features at the touch of a button. By moving this key to the left, you open the phonebook. Move the key to the right to access Caller ID information. To use this four-way key, place your thumb over the key and move to the four positions to get the feel of how it moves and operates.

View the phonebook Four-way Function Key

View the Caller ID

Using the Menus
The menus for the handset and the base work in Down the same way: To open the menu, press the [menu/select] key. The arrow pointer on the left side of the line shows which menu item is currently highlighted. Use [ ] on the fourway function key to move the pointer up and [ ] to move the pointer down. To select the highlighted option, press [menu/select]. To go back to the previous screen, press [left] on the four-way function key. To exit the menu on the handset, press [ ]. To exit the menu on the base, press [ ]. If you dont press any keys for thirty seconds, the phone will time out and exit the menu. (When setting the day and time, the time-out period is extended to two minutes.) For ANSW. SETUP, GLOBAL SETUP, DAY & TIME and REGISTER HANDSET (base only) menu options, make sure the line is not in use and the handsets are within range of the base.
Entering Text from Your Phone
You can use the number keypad on your handset or base to enter text by referring to the letters printed on each number key. When you press the number key in a text entry field, the phone displays the first letter printed on the number key. Press the number key twice to display the second letter and three times to display the third. Capital letters are displayed first, then lower case letters, and then the number on the key. If two letters in a row use the same number key, enter the first letter, then use [right] on the four-way function key to move the cursor to the next position to enter the second letter. For example, to enter the word Movies: ) Press [6] once to enter M. 2) Use [right] on the four-way function key to move the cursor to the right. 3) Press [6] six times to enter o. 4) Press [8] six times to enter v. 5) Press [4] six times to enter i. 6) Press [3] five times to enter e. 7) Press [7] eight times to enter s. 8) Press [menu/select] to end your text entry. If you make a mistake while entering a name, use [right] or [left] on the fourway function key to move the cursor to the incorrect character. Press [clear/intcom] on the handset or [clear/mute] on the base to erase the wrong character, and then enter the correct character. To delete all characters, press and hold [clear/intcom] on the handset or [clear/mute] on the base.

Deleting a Single Phonebook Entry
) 2) 3) 4) 5) With the phone in standby, press [ ]. Find the entry that you want to delete and press [menu/select]. Select DELETE. DELETE ENTRY? appears in the display. Move the cursor to select YES. Press [menu/select]. You will hear a confirmation tone, and DELETED! appears in the display. Setting Up the Phonebook
Deleting all Phonebook Entries
) With the phone in standby, press [ ]. 2) Press [menu/select], and then select DELETE ALL. DELETE ALL?. appears in the display. 3) Move the cursor to select YES. 4) Press [menu/select]. You will hear a confirmation tone, and DELETED!. appears in the display.
Copying Phonebook Entries to Another Station
You can transfer phonebook entries from one station to another without having to re-enter names and numbers. You can transfer one phonebook entry at a time or all phonebook entries at once. ) With the phone in standby, press [ ]. 2) To copy one entry, find the phonebook entry you want to copy. Press [menu/select], and then select COPY. To copy all entries, press [menu/select], and then select COPY ALL. 3) Move the cursor to select the station which you want to transfer the entries to and then press [menu/select]. If you select COPY ALL, ARE YOU SURE? appears on the display screen. Move the cursor to select YES, and then press [menu/select]. 4) The phonebook entries will be transferred to the designated station. During the copy process, the receiving station shows RECEIVING and the ID of the sending station. 5) When the transfer is completed, DONE! appears on the station.
Notes: If the station you want to transfer to already has seventy entries in its phonebook, you will hear a beep, and NOT ENOUGH MEMORY IN RECEIVING UNIT appears on the display. If the selected station is out of range or data transfer is cancelled, UNAVAILABLE appears in the display. Phonebook listings will not be transferred.
Customizing Your Handsets
All of the following options are set separately for each handset, so you can customize a handset for each room in your house.
Changing the Handset Banner
Each handset will display a banner name once it is registered to the base. The default banner is Handset #1, Handset #2, etc. You can change the name your phone displays by changing the banner display. If you have more than one handset, the banner name identifies your handset. ) Press [menu/select]. 2) Select the HANDSET SETUP menu, and then the BANNER submenu. 3) Use the keypad to enter or edit the banner name. (See Entering Text from Your Phone on page 21 for detailed instructions on entering text.) 4) Press [menu/select]. You will hear a confirmation tone.

Chain dialing from the phonebook
Using Your Phone If you often have to enter a series of digits or a code number during a call, you can save that code number to a phonebook entry. When your call connects, just use the phonebook to transmit the saved code number. (This is referred to as chain dialing.) ) Enter the code number (up to twenty digits) into the phonebook (see Creating Phonebook Entries on page 24). Be sure to enter the code number into the phonebook exactly as you would enter it during a call. 2) During a call, when you hear the prompt that tells you to enter the code number, press [ 3) Use [ ] or [ ] to select the phonebook entry that contains the digits you want to send. ].
4) Press [menu/select]. The phone sends the digits of the code number exactly as you saved them in the phonebook entry.
Switching to the Handset Speakerphone During a Call
To switch a normal call to the speakerphone, press [ normal call, press [ ]. ] on the handset. To switch from a speakerphone call to a
Using Caller ID, Call Waiting, and Redial Lists
If you subscribe to Caller ID service from your phone company, your phone will show you the callers phone number and name (if available) whenever a call comes in. If you subscribe to Caller ID on Call Waiting, the phone will also show you the name and the number of any call that comes in while youre on the line.

Using the Caller ID List

You can store up to thirty Caller ID numbers in each station. Caller ID records are stored from newest to oldest. Once your Caller ID list is full, the oldest record will be automatically deleted when a new call is received. To open the Caller ID list, press [ ] (on the right side of the four-way key). The phone will show the number of new Caller ID records (that is, records you have not reviewed yet) and the total number of stored records. Use [ ] and [ ] to scroll through the list. (New records have an asterisk next to the received time.)
Making a Call from a Caller ID Record
) 2) 3) 4) With the phone in standby, press [ ] to open the Caller ID list. Use [ ] and [ ] to find the Caller ID record you want to dial. If you need to add (or delete) a 1 to the beginning of the displayed phone number, press [ /tone]. * Press [ /flash] or [ ] on the handset or [ ] on the base to dial the number.
Note: You can also press [ /flash] or [ ] on the handset or [ ] on the base before you open the caller ID list. Find the phone number you want to dial, and then press [menu/select]. Whats this add or delete a 1 about? Any phone number in the Caller ID records might (or might not!) have a 1 at the front, depending on how different phone companies send the Caller ID information. The phone dials the number exactly as it appears in the Caller ID record. If the phone number is a long distance or toll call, but the Caller ID record does not have a 1 in front of the number, press [ /tone] to add it. If the phone number is a local or non-toll call, but the Caller ID record has a * 1 in front of the number, press [ /tone] to delete it. *

Redialing a Number

You can quickly redial the last five numbers dialed on each station. ) With the phone in standby, press the [redial/pause] to open the redial list. 2) Use [ ] and [ ] or [redial/pause] to scroll through the redial list. 3) When you find the number you want to dial, press [ /flash] or [ ] on the handset or [

] on the base.

Notes:If the number exceeds 32 digits, only the first 32 digits are retained in redial memory. If the redial memory is empty, EMPTY appears in the display and you will hear a beep. You can also press [ /flash] or [ ] on the handset or [ ] on the base before you open the redial list. Find the phone number you want to dial, and then press [menu/select].

Deleting a Redial Record

If you want to delete a phone number from the redial list, follow the steps below: ) With the phone in standby, press [redial/pause]. 2) Use [ ] and [ ] to scroll through the redial list. 3) When you find the redial number you want to delete, press [menu/select] and select DELETE ENTRY. 4) When the phone asks you to confirm, select YES. The redial number is deleted.
Adjusting the Ringer, Earpiece and Speaker Volume
Adjusting the Ringer Volume
You can choose from four ringer volume settings (off, low, medium, and high) separately on each handset or the base. ) With the phone in standby, press [ ] or [ ]. The display shows the current volume level and the station sounds the ringer at that level. 2) Use [ ] to make the ringer volume louder or [ ] to make it softer or turn it completely off. 3) When you hear the ringer volume level you want to use, stop pressing keys. The station will use the new ringer volume starting with the next incoming call. Note: If you set the ringer volume to OFF, the station wont ring. The other stations will ring according to their individual settings.
Muting the Ringer (One call only)
While the phone is ringing, press [ /mute] or [ ] on the handset, or [clear/mute] or [ ] on the base to mute the ringer for this call. The phone will ring again on the next call. (The handset must be off the cradle to mute the ringer.)
Adjusting the Earpiece Volume
You can choose from six volume levels for the handset earpiece. To adjust the earpiece volume while on a call, press [ ] (to make it louder) or [ ] (to make it softer). The handset display shows the current volume level for the earpiece.
Adjusting the Speaker Volume
Handset Speaker: You can choose from six volume levels for the handset speaker while on a speakerphone call or when the handset is accessing the answering system. To adjust the handset speaker volume, press [ ] (to make it louder) or [ ] (to make it softer). The handset display shows the current volume level for the handset speaker. Note: The handset earpiece and the handset speaker have separate volume settings. Base Speaker: You can choose from ten volume levels for the base speaker while on a speakerphone call or when the answering system announces or plays a message. To adjust the base speaker volume, press [ ] (to make it louder) or [ ] (to make it softer). The base display shows the current volume level for the base speaker.

Selecting a Greeting

Once you have recorded a personal greeting, the phone automatically switches to your personal greeting. You can also switch back and forth between the pre-recorded greeting and your own greeting at any time. ) On the base, press [menu/select]. 2) Select the ANSW. SETUP menu, and then the GREETING OPTIONS submenu. The system plays the current greeting. 3) To keep this greeting, do nothing. 4) To switch to the other greeting, press [ ] or [ ] on the four-way function key while the system is playing the current greeting. 5) Each time you press [ ] or [ ], the system switches between the pre-recorded and the personal greeting. The last greeting you hear is used as the current greeting.
Deleting Your Personal Greeting
You can delete your personal greeting from the base. You cannot delete the pre-recorded greeting. ) On the base, press [menu/select]. 2) Select the ANSW. SETUP menu, and then the GREETING OPTIONS submenu. The system plays the current greeting. 3) While the personal greeting is playing, press [ ]. 4) The system announces Greeting has been deleted, and switches back to the pre-recorded greeting.
Selecting the Language for Announcements
You can select the language of your answering system announcements. The default system language is English. ) Press [menu/select]. 2) Select ANSW. SETUP, and then the ANSW. LANGUAGE submenu. 3) Move the cursor to choose a language. for US models: Choose ENGLISH or ESPAOL (Spanish). for Canadian models: Choose ENGLISH or FRANAIS (French). 4) Press [menu/select]. You will hear a confirmation tone.
Setting the Number of Rings
The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after two, four, or six rings. If you enable the Toll Saver (TS) setting, the answering system picks up after two rings if you have new messages, and after four rings if there are none. This way, if you make a long distance call to check your messages, you can hang up after the third ring to avoid long distance billing charges. ) Press [menu/select]. 2) Select the ANSW. SETUP menu, and then the RING TIME submenu. 3) Move the cursor to select a ring time (TOLL SAVER, 2 TIMES, 4 TIMES, or 6 TIMES). 4) Press [menu/select]. You will hear a confirmation tone.

Setting the Day & Time
If you do not set the clock on your answering system, your messages may not have the correct time and day stamp. ) Press [menu/select]. 2) Move the cursor to DAY & TIME and press [menu/select]. 3) Use [ ] and [ ] to select the day of the week, and press [menu/select]. 4) Use the number keypad ([0] through [9]) to enter the hour and minutes. 5) Use [ ] and [ ] to select AM or PM, and press [menu/select]. You hear a confirmation tone. Notes:You can set the day and time from the handset, but the day and time do not appear on the handset display. If the power goes out on the base, you might have set the day and time again.
Setting the Record Time (or Announce only)
You can choose how long callers have to record a message. Set the record time to 1 MINUTE or 4 MINUTES to limit the time for incoming messages. If you set the record time to ANNOUNCE ONLY, the answering system answers the call but prevents callers from leaving a message. ) Press [menu/select]. 2) Select the ANSW. SETUP menu, and then the RECORD TIME submenu. 3) Move the cursor to select a record time (1 MINUTE, 4 MINUTES, or ANNOUNCE ONLY). 4) Press [menu/select]. You will hear a confirmation tone. While your answering system is set to ANNOUNCE ONLY, the message counter on the base LCD displays A. If you are using the prerecorded greeting, the system automatically switches to the following message: Hello, no one is available to take your call. Please call again. If you are using a personal greeting, the system continues to use that greeting.
Activating the Message Alert
The message alert feature sounds a short alert tone every fifteen seconds whenever you have a new message. To turn on the message alert: ) Press [menu/select]. 2) Select the ANSW. SETUP menu, and then the MESSAGE ALERT submenu. 3) Move the cursor to select ON or OFF. 4) Press [menu/select]. You will hear a confirmation tone.
Activating the Base Call Screen
With the call screen feature, you can listen to callers as they leave a message without answering the call. ) Press [menu/select]. 2) Select the ANSW. SETUP menu and then the CALL SCREEN submenu. 3) Move the cursor to select ON or OFF. 4) Press [menu/select]. You will hear a confirmation tone.
Using the Answering System
Turning Your Answering System On and Off
From the base ) With the phone in standby, press. [ answer on/off]. 2) The system announces Answering System is on and plays the current greeting. 3) ANSWER ON appears on the base display. ) With the phone in standby, press. [ answer on/off]. 2) The phone announces Answering System is off. 3) ANSWER OFF appears on the base display. From the handset ) Press [menu/select]. 2) Select the ANSW. SETUP menu, and then the ANSWER SETUP submenu. 3) Move the cursor to select ON. 4) Press [menu/select]. You will hear a confirmation tone. ) Press [menu/select]. 2) Select the ANSW. SETUP menu, and then the ANSWER SETUP submenu. 3) Move the cursor to select OFF. 4) Press [menu/select]. You will hear a confirmation tone.

Turning On

Turning Off
Note: If the answering system announces No remaining time when you turn it on, the memory is full (the message counter also shows FL). The answering system cant record any new messages until you delete some of the saved ones.

Reviewing Messages

The message counter on the base LCD displays the number of messages stored in memory. When you have new messages (that you have not listened to yet), [ ] on the base and the new message LED on the handset flash. The answering system plays your new messages first. If you have no new messages, the system plays your old messages. You can review your messages from the base or from the handset: From the base ]. The system announces the Press [ Playing new number of new and old messages, then plays the first new message followed by the day and messages time it was received. Then the system plays the new messages in the order they were received. Repeating a message Skipping a message Deleting a message Deleting all messages Playing old messages Ending the message review Press [ ] once to go to the beginning of the current message. Press [ ] repeatedly to go back to a previous message. Press [ ] to go to the beginning of the next message. While a message is playing, press [ ]. The message is permanently deleted. While the phone is in standby, press [ ]. When the system asks you to confirm, press [ ] again. All messages are permanently deleted. After you listen to your new messages, press. [ ] again to play your old messages. ] to stop the message playback and Press [ return to standby. From the handset Press [ /mute]. The system announces the number of new and old messages, then plays the first new message followed by the day and time it was received. Then the system plays the new messages in the order they were received. Press [1] once to go to the beginning of the current message. Press [1] repeatedly to go back to a previous message. Press [3] to go to the beginning of the next message. While a message is playing, press [4]. The message is permanently deleted. Not available. After you listen to your new messages, press. [ /mute] again to play your old messages. Press [5] to stop the message playback. Press [ ] to exit the system and return to standby, or press [2] to restart the message playback.

Screening Calls

From the base While the system is taking the message, simply listen to the caller over the base speaker. To answer the call and speak to the caller, press [ ]. To mute the call screen and allow the caller to continue leaving the message, press [ ]. From the handset While the systems is recording the message, press. [ /mute]. If another handset is screening a call, you will hear a beep and you will not be able to screen the call. To answer the call and speak to the caller, press [ /flash]. To mute the call screen and allow the caller to continue leaving the message, press [ ] or return the handset to the cradle.

Accessibility. 4 Accessory handsets. 12 Answering calls.. 30 Answering system Reviewing messages. 47 Setting up.. 42 Turning on/off.. 46 When away from home. 48 Any key answer.. 29 Area code.. 33 Audio tone. 36 AutoTalk.. 29.

Belt clip..11

Handset Accessory handsets. 12 Banner.. 28. Choosing a ringer.. 28 Copying phonebook entries. 27 Entering text.. 21 Finding.. 37 Parts of the handset. 17 Reading the display. 19 Registering.. 12 Resetting.. 54, 55 Handset to base code. 56 Hanging up.. 30 Headset.. 41 Hold... 37 Index
Caller ID.. 32 Deleting Caller ID records. 33 Making calls from.. 32 Call screening.. 45, 48. Call waiting.. 34. Chain dialing. 31 Conferencing.. 37
Day and time.. 44 Dial mode..11, 40
FCC statements.. 59 Finding a handset.. 37 Four-way function key. 20
Banner.. 28 Base Installing.. 7 Parts of the base.. 18 Reading the display. 19 Wall mounting.. 13 Battery Battery life.. 50 Installing.. 6 Low battery alert.. 51 Replacement and handling. 51
Installation.. 5 Intercom.. 39
Greetings Deleting.. 43 Recording.. 42. Selecting.. 42

Key touch tone.. 23

Language Answering system announcements. 43. Display.. 22 Line mode for base. 56. Liquid damage.. 57 Low battery alert.. 51 Index
Personal identification number. (PIN).. 48 Personal ring. 23, 25 Phonebook.. 24 Copying entries.. 27 Creating new entries.. 24 Deleting entries.. 26 Editing entries.. 25 Finding entries. 25 Making a call from. 31 Storing Caller ID or redial numbers.. 26. Privacy mode.. 39 Pulse dialing..11, 40
Safety notices. 58 Screening calls.. 45, 48 Security code.. 48. Seven-digit dialing. 33
Text, entering.. 21 Tone dialing..11, 40 Transferring a call.. 38 Troubleshooting.. 52
Maintenance.. 50. Making calls.. 30 Using Caller ID. 32 Using redial. 34 Using the phonebook. 31 Message alert.. 45, 48 Mute Microphone. 40 Ringer.. 35
Voice mail service.. 41. Volume, adjusting.. 35
Redial Deleting a record. 34. Making a calls with.. 34 Ringer Choosing a handset ringer. 28 Muting.. 35 Personal ring.. 23, 25 Volume.. 35
Wall mounting the base. 13 Warranty.. 61

Out of range.. 56

Remote Operation Card

CUT CUT

REMOTE OPERATION CARD
Remote access away from home
1. Call your phone number from a touch-tone phone. 2. During the outgoing message, press 0 and enter your PIN code. The answering system announces the number of messages stored in memory and the voice prompts. 3. To quit, hang up the phone. CUT
Turn on the answering system remotely
1. Call your phone and let it ring 10 times until you hear a beep. 2. Press 0 and then enter your PIN code. 3. Press 0 then 5 to stop the announcement. 4. Press 0 then 6 to turn the answering system on.