Operating Instructions For 3 Function Cable Remote Control

UR3-EXP

1 Introduction
The remote control is designed to operate the Scientific-Atlanta Explorer 2000 and 3000 Series and the Pioneer Voyager set top boxes and the majority of TV and VCR/DVD equipment on the market.

3 Button Functions

STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. *Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the VCR/VOD button is in the VCR position when using your VCR.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds. STEP3 Press the [DEVICE] button you wish to store in the System On/Off button and repeat this until you stored all the power commands into the System On/Off button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.
C. To Find the Three Digit Code Number That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV or VCR) you wish to verify and the [SELECT ]button simultaneously for 3 seconds. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. Note : Ten blinks is equal to the number 0.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.

F. Volume Punch Through:

By following the steps below, the user can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is TV volume control. If you wish to store the CABLE volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP 3.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.
D. Programming a second TV to VCR Mode.
STEP1 Press the [VCR] button to be programmed and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV] device button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP4 Store the three-digit code number by pressing the [VCR] button once again. The device LED will blink twice to confirm that the code has been stored.

4 Operations

Default State : Device Default : Scientific Atlanta Explorer 2000/3000 & Pioneer Voyager Volume Default : TV volume and mute through the TV, with the option of controlling volume and mute through the Cable Converter. Refer to Section F for programming the volume and mute through your Cable Converter.
5 Programming the Remote Control.
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD) STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed. *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
*Tip : The device LED will light on for 20 seconds. The next step must be entered while LED is on. STEP3 Point the remote control toward the equipment and alternately press the [CH+] (or [CH-]) button and the [MUTE] button. If the right code number is sent, the equipment will turn off. *Tip : You can verify that you selected the correct code by pressing the [MUTE] button again. The equipment should either turn on or turn off.

G. LOW BATTERY WARNING:

When the battery is low (2.0V-2.3V) and needs to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.
Universal Remote Control, Inc.

www.universalremote.com

OEE-0049A Rev 07(06/30/04)
System On/Off button : This button is designed to send out power commands for two or all three devices with one button press. Please refer to section E for details.
E. Programming the System On/Off Button.
This is designed to program the System on/off button so that it can send out up to three power on/off commands for the devices you programmed into the remote control.

H. Memory Lock System:

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
I. Write your device Set-up codes:
TV Set-up Code Number : VCR Set-up Code Number :
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST

Operating Instructions For 3 Function Cable Remote Control

UR3-EXP

1 Introduction
The remote control is designed to operate the Scientific-Atlanta Explorer 2000 and 3000 Series and the Pioneer Voyager set top boxes and the majority of TV and VCR/DVD equipment on the market.

3 Button Functions

SYSTEM ON/OFF send out power commands for two
or all three devices with one button press.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. *Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the VCR/VOD button is in the VCR position when using your VCR.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
FOUR-WAY CURSOR KEYS allow you to navigate through

the on-screen menus

DEVICE KEYS allow you to
turn on and off your TV, VCR, and CABLE box. They are also used to setup the remote control
C. To F i n d t h e T h re e D i g i t C o d e Number That was Store d i n the Device.
STEP1 Press the [DEVICE] button (TV or VCR) you wish to verify and the SELECT button simultaneously for 3 seconds. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. Note : Ten blinks is equal to the number 0.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. STEP3 Replace the battery compartment cover.
GUIDE displays the program guide
INFO displays channel and

program information

SETTINGS displays current

cable box settings

PAGE moves the menu
forward and backward one page

MUTE turns volume off

EXIT exits out of on-screen menus
VOLUME turns the volume up and down
CH changes the channel up and down
The Scientific-Atlanta Explorer Converter has an on-screen program guide that can be sorted several different ways: A sorts the guide by time B sorts the guide by theme C sorts the guide by title Consult your converter manual for more information on the on-screen guide
NUMBER KEYS allow direct access to
specific channels and menu options
LAST recalls the last channel that

was viewed

FAV steps through favorite channels
B. A u t o S e a rc h M e t h o d.
VCR/DVD KEYS perform standard
VCR and DVD functions when in VCR mode, and Video-on-Demand functions when in VOD mode.
BYPASS switches between the cable

box and TV

VCR/VOD switches the VCR controls into

Video-on-Demand controls

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on. *Tip : The device LED will light on for 20 seconds. The next step must be entered while LED is on. STEP3 Press the [CH+] or [CH-] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release The[CH+] or [CH-] button as soon as the equipment turns off. *Tip : You can verify that you selected the correct code by pressing the [MUTE] button. The equipment should either turn on or turn off.

D. P rogramming a second TV to VCR Mode.
STEP1 Press the [VCR] button to be programmed and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV] device button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. STEP4 Store the three-digit code number by pressing the [VCR] button once again. The device LED will blink twice to confirm that the code has been stored.
TV/VCR switches the VCR between TV and

VCR mode

4 Operations
Default State : Device Default: Scientific Atlanta Explorer 2000/3000 & Pioneer Voyager Volume Default : TV volume and mute through the TV, with the option of controlling volume and mute through the Cable Converter. Refer to Section F for programming the volume and mute through your Cable Converter.
5 Programming the Remote Control.
A. T h re e - D i g i t C o d e P ro g r a m m i n g M e t h o d.
The remote control can be programmed by pressing in a three digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD) STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed. *Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
E. P ro g r a m m i n g t h e S y s t e m O n / O ff B u t t o n.
This is designed to program the System on/off button so that it can send out up to three power on/off commands for the devices you programmed into the remote control.
Universal Remote Control, Inc.

www.universalremote.com

OEE-0049A Rev 03(12/10/01)
System On/Off button : This button is designed to send out power commands for two or all three devices with one button press. Please refer to section E for details.
STEP1 Press the [CBL] button. STEP2 Press the [SYSTEM] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds. STEP3 Press the [DEVICE] button you wish to store in the System On/Off button and repeat this until you stored all the power commands into the System On/Off button. STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.
I. Wr i t e y o u r d e v i c e S e t - u p c o d e s :
TV Set-up Code Number : VCR Set-up Code Number :
MAKER(BRAND) NAME JCPENNY JENSEN JVC KENWOOD KLOSS KMC KTV LODGENET LOGIK LUXMAN LXI MAGNAVOX CODE NUMBER (3 DIGIT) LIST MARANTZ MATSUI 164 MEMOREX 072 METZ 088 MGA MINERVA 088 MITSUBISHI 226 MTC NAD NEC NIKEI 043 ONKING 043 ONWA 043 OPTONICA ORION PANASONIC 206 PENNEY PHILCO PHILIPS 059 PIONEER 070 PORTLAND PROSCAN PROTON 131 QUASAR RADIO SHACK 043 RCA 221 REALISTIC RUNCO 181 SAMPO 220 SAMSUNG 070 SANYO SCOTT SEARS SELECO 189 SHARP SIGNATURE 072 SONY SOUNDESIGN SPECTRICON 112 SSS SUPRE MACY 002

MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST SYLVANIA SYMPHONICS 052 TANDY 081 TATUNG 209 TECHNICS TECHWOOD TEKNIKA TELERENT 072 TERA 172 TMK 004 TOSHIBA TOTEVISION 143 UNIVERSAL VIDEO CONCEPTS 146 VIDIKRON VIDTECH 004 WESTING HOUSE 076 WARDS YAMAHA YORK 004 YUPITERU 043 ZENITH ZONDA 112

VCR & TV/VCR

MAKER(BRAND) NAME JCL JCPENNY JENSEN JVC KENWOOD LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX CODE NUMBER (3 DIGIT) LIST MGA 059 MINOLTA MITSUBISHI MTC MULTITECH NEC 039 NORDMENDE 043 OPTONICA PANASONIC PENTAX PHILCO 067 PHILIPS PILOT 101 PIONEER 048 PORTLAND 108 QUARTZ QUASAR RADIO SHACK 123 RCA REALISTIC RICO SALORA 014 SAMSUNG 159 SANSUI SANYO SCOTT 159 SEARS 101 SHARP SHINTOM 024 SIGNATURE 034 SONY SOUNDESIGN 034 STS 013 SYLVANIA SYMPHONIC 034 TANDY TATUNG 023 TEAC 043 023
MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST TECHNICS TEKNIKA TMK 006 TOSHIBA TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VIDEO CONCEPTS VIDEOSONIC 040 WARDS YAMAHA ZENITH 058

6 Set-up Code Tables

CABLE TV
Converter Converter Model Code No Remote UR3-EXP S/A and Pioneer Explorer/Voyager 001
MAKER(BRAND) NAME A MARK ADMIRAL AKAI AMPRO ANAM AOC AUDIOVOX CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO CODE NUMBER (3 DIGIT) LIST 229 DAYTRON DWIN 161 DYNASTY 043 DYNATECH ELECTROHOME 143 EMERSON ENVISION 070 FISHER FUNAI FUTURETECH 043 GE GOLDSTAR/LG HALL MARK 004 HARMAN KARDON 211 HITACHI 208 INFINITY 164 INKEL 129 JBL JCP 070

F. Volume Punch Through:

By following the steps below, the user can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is TV volume control. If you wish to store the CABLE volume control in CBL mode, use the following steps. STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. *Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CBL] button. The device LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in step 3.
*Note : For TV/VCR combination unit, Please use following steps to operate the Volume control. STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will light on for 20 seconds. STEP2 Press the [VOL+] button. STEP3 Press the [VCR] button. The LED will blink twice to confirm the programming. DVD(VCR)

MAKER(BRAND) NAME ALPINE APEX DIGITAL DENON GE GOLDSTAR/LG HARMAN KARDON HITACHI JVC MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO PANASONIC PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG SHARP SONY TOSHIBA YAMAHA ZENITH CODE NUMBER (3 DIGIT) LIST 194
MAKER(BRAND) NAME AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROOKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DIMENSIA DBX DYNATECH ELECTROHOME EMERSON CODE NUMBER (3 DIGIT) LIST FISHER FUNAI 034 GE GO VIDEO 136 GOLDSTAR/LG 114 HARMAN KARDON HITACHI 156 HUGHES 013 INSTANTREPLAY 031
G. L O W B AT T E RY WA R N I N G :
When the battery is low (2.0V-2.3V) and needs to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [DEVICE] button is pressed to turn on equipment.
H. M e m o ry L o c k S y s t e m :
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.