Operating Instructions For 3 Function Cable Remote Control

UR3-J22TWM

1 Introduction
The remote control is designed to operate the Motorola CFT2200 set top box and the majority of TV and VCR/DVD equipment on the market.

3 Button Functions

*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off. *Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off. STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The LED will blink twice to confirm that the code has been stored. *Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.
STEP4 Press the same [DEVICE] button to store the code. The LED will blink twice to confirm that the code has been stored.
indicates remote control activity

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AAA alkaline batteries. STEP1 Remove the battery compartment cover on the back of your remote control. STEP2 Check battery polarity carefully, and install the batteries as shown below. STEP3 Replace the battery compartment cover.
Install two AAA alkaline batteries as shown here
allow direct access to specific channels and menu options
allow you to turn on and off your TV, VCR, and CABLE box. They are also used to setup the remote control changes the channel up and down
C. To Find the Three Digit Code Number That was Stored in the Device.
STEP1 Press the [DEVICE] button (TV POWER or VCR POWER) you wish to verify and the [SEL] button simultaneously for 3 seconds. *Tip : The LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [INFO] button. The LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off. Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138. Note : Ten blinks is equal to the number 0.
STEP4 Store the three-digit code number by pressing the [VCR POWER] button once again. The LED will blink twice to confirm that the code has been stored.

E. Volume Punch Through:

By following the steps below, the user can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is TV volume control. If you wish to store the CABLE volume control in CBL mode, use the following steps. STEP1 Press the [CABLE POWER] button and the [SEL] button simultaneously for 3 seconds. *Tip : The LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL +] button. STEP3 Press the [CABLE POWER] button. The LED will blink twice to confirm the programming. To return to original state: If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV POWER] in step 3.
turns the volume up and down displays help for on-screen display screens
INFO future use FAV cycles through your favorite channels MUTE turns volume off

future use

recalls the last channel that was viewed switches between cable TV and Music Choice TM displays the quick function screen
MOVIES future use INFO displays channel and program information
exits the on-screen display menus
GUIDE displays the program guide CURSOR KEYS navigate through on-screen guides
displays the main on-screen display menu
SEL selects options from the program guide and
be used to set up the remote.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps: STEP1 Turn on the equipment you wish to operate. STEP2 Press the [DEVICE] button (TV POWER or VCR POWER) to be programmed and the [SEL] button simultaneously for 3 seconds. The LED will turn on. *Tip: The LED will light on for 20 seconds. The next step must be entered while LED is on. STEP3 Point the remote control toward the equipment and alternately press the [CH+] (or [CH-]) button and the [MUTE] button. If the right code number is sent, the equipment will turn off. *Tip : You can verify that you selected the correct code by pressing the [MUTE] button again. The equipment should either turn on or turn off.
DAY +/- moves the program guide one day
pages through on-screen menu and program guide screens forward and backward
TV/VCR switches between control of
your TV and your VCR initiates VCR recording through the on-screen menu (if so equipped)
VCR/DVD KEYS perform standard VCR and DVD
functions when in VCR mode.
D. Programming a second TV to VCR Mode.
STEP1 Press the [VCR POWER] button to be programmed and the [SEL] button simultaneously for 3 seconds. *Tip : The LED will turn on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [TV POWER] button to pick up the TV code table. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables.
5 Programming the Remote Control.
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual. STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD) STEP2 Press the [DEVICE] button (TV POWER or VCR POWER) to be programmed and the [SEL] button simultaneously for 3 seconds. The LED will turn on indicating the unit is ready to be programmed. *Tip : The LED will stay lit for 20 seconds. The next step must be entered while the LED is on. STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.

F. LOW BATTERY WARNING:

When the battery is low (2.0V-2.3V) and needs to be replaced with fresh batteries, the LED will blink twice whenever a device [POWER] button is pressed to turn on equipment.

4 Operations

Default State : Device Default: Motorola CFT2200 Volume Default : TV volume and mute through the TV, with the option of controlling volume and mute through the Cable Converter. Refer to Section E for programming the volume and mute through your Cable Converter.

G. Memory Lock System:

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control
Universal Remote Control, Inc.

www.universalremote.com

OEE-0035N Rev 07 (07/09/04)
H. Write your device Set-up codes:
TV Set-up Code Number : VCR Set-up Code Number :
MAKER(BRAND) NAME ENVISION FISHER FUJITSU FUNAI FUTURETECH GE CODE NUMBER (3 DIGIT) LIST
MAKER(BRAND) NAME MTC MULTITECH NAD NEC NIKEI NIKKO NTC ONKING ONWA OPTIMUS OPTONICA ORION PANASONIC PENTAX PHILCO CODE NUMBER (3 DIGIT) LIST 238
MAKER(BRAND) NAME TATUNG TEAC TECHNICS TECHNOL ACE TECHWOOD TEKNIKA CODE NUMBER (3 DIGIT) LIST 164 TELERENT 072 TERA 172 THOMPSON 166 TNCI 073 TMK 004 TOSHIBA TOTEVISION 247 UNITECH 239 UNIVERSAL VIDEO CONCEPTS VIDEOSONIC 239 VIDIKRON 164 VIDTECH 004 WESTING HOUSE 076 WARDS 239 YAMAHA 238 YORK 004 YUPITERU 043 ZENITH 096 ZONDA 112
MAKER(BRAND) NAME DBX DYNATECH ELECTROHOME ELECTROPHONIC EMERSON CODE NUMBER (3 DIGIT) LIST 063 156
MAKER(BRAND) NAME PHILCO PHILIPS PILOT PIONEER PORTLAND PROFITRONIC PROTEC QUARTZ QUASAR RADIO SHACK RADIX RANDEX RCA CODE NUMBER (3 DIGIT) LIST 053 REALISTIC RICO 058 SALORA 014 SAMSUNG 159 SANKY 053 SANSUI 025 SANYO 040 SCOTT 159 SEARS 034 SHARP SHINTOM 024 SHOGUN 040 SIGNATURE 034 SINGER 024 SONY SOUNDESIGN 034 STS 013 SYLVANIA SYMPHONIC 034 TANDY TATUNG 023 TEAC TECHNICS TEKNIKA THOMAS 034 TMK TOSHIBA TOTEVISION UNITECH 040 VECTOR RESEARCH 012 VIDEO CONCEPTS VIDEOSONIC 040 WARDS WESTING HOUSE XR-YAMAHA ZENITH 058 025

DVD(VCR)

MAKER(BRAND) NAME CODE NUMBER (3 DIGIT) LIST

6 Set-up Code Tables

*Note : For TV/VCR combination unit, Please set up TV code number in the TV mode to operate the volume, Set up VCR code number in the VCR mode to operate the VCR functions.